Pull timer fixes from Ingo Molnar:
"Main changes:
- Fix the deadlock reported by Dave Jones et al
- Clean up and fix nohz_full interaction with arch abilities
- nohz init code consolidation/cleanup"
* 'timers-nohz-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
nohz: nohz full depends on irq work self IPI support
nohz: Consolidate nohz full init code
arm64: Tell irq work about self IPI support
arm: Tell irq work about self IPI support
x86: Tell irq work about self IPI support
irq_work: Force raised irq work to run on irq work interrupt
irq_work: Introduce arch_irq_work_has_interrupt()
nohz: Move nohz full init call to tick init
Pull m68k updates from Geert Uytterhoeven:
"Summary:
- a fix for an intermittent crash in macsonic and hilkbd, marked for
stable,
- build fixes for uncommon configs.
Note: "m68k: AMIGA_BUILTIN_SERIAL should depend on TTY" was also
picked up by GregKH for his TTY/Serial patches tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Reformat arch/m68k/mm/hwtest.c
m68k: Disable/restore interrupts in hwreg_present()/hwreg_write()
m68k: AMIGA_BUILTIN_SERIAL should depend on TTY
m68k: Add missing ioport_unmap()
m68k/atari - stram: Add missing #include <linux/ioport.h>
hwreg_present() and hwreg_write() temporarily change the VBR register to
another vector table. This table contains a valid bus error handler
only, all other entries point to arbitrary addresses.
If an interrupt comes in while the temporary table is active, the
processor will start executing at such an arbitrary address, and the
kernel will crash.
While most callers run early, before interrupts are enabled, or
explicitly disable interrupts, Finn Thain pointed out that macsonic has
one callsite that doesn't, causing intermittent boot crashes.
There's another unsafe callsite in hilkbd.
Fix this for good by disabling and restoring interrupts inside
hwreg_present() and hwreg_write().
Explicitly disabling interrupts can be removed from the callsites later.
Reported-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: stable@vger.kernel.org
If CONFIG_TTY=n:
drivers/built-in.o: In function `rs_flush_buffer':
amiserial.c:(.text+0x1f626): undefined reference to `tty_wakeup'
drivers/built-in.o: In function `transmit_chars':
amiserial.c:(.text+0x1f6c8): undefined reference to `tty_wakeup'
drivers/built-in.o: In function `change_speed':
amiserial.c:(.text+0x1f80a): undefined reference to `tty_termios_baud_rate'
amiserial.c:(.text+0x1f88c): undefined reference to `tty_termios_baud_rate'
drivers/built-in.o: In function `check_modem_status':
amiserial.c:(.text+0x1faa6): undefined reference to `tty_hangup'
amiserial.c:(.text+0x1faec): undefined reference to `tty_wakeup'
drivers/built-in.o: In function `get_serial_info':
amiserial.c:(.text+0x1fb88): undefined reference to `tty_lock'
amiserial.c:(.text+0x1fbc0): undefined reference to `tty_unlock'
drivers/built-in.o: In function `rs_open':
amiserial.c:(.text+0x1fdc6): undefined reference to `tty_port_block_til_ready'
drivers/built-in.o: In function `set_serial_info':
amiserial.c:(.text+0x1fe0c): undefined reference to `tty_lock'
amiserial.c:(.text+0x1fea0): undefined reference to `tty_unlock'
amiserial.c:(.text+0x1fed0): undefined reference to `tty_unlock'
amiserial.c:(.text+0x1ffaa): undefined reference to `tty_unlock'
drivers/built-in.o: In function `receive_chars':
amiserial.c:(.text+0x2005c): undefined reference to `do_SAK'
amiserial.c:(.text+0x200e0): undefined reference to `tty_insert_flip_string_flags'
amiserial.c:(.text+0x2013c): undefined reference to `tty_insert_flip_string_flags'
amiserial.c:(.text+0x20148): undefined reference to `tty_flip_buffer_push'
drivers/built-in.o: In function `rs_close':
amiserial.c:(.text+0x20744): undefined reference to `tty_port_close_start'
amiserial.c:(.text+0x2078a): undefined reference to `tty_ldisc_flush'
amiserial.c:(.text+0x20798): undefined reference to `tty_port_close_end'
drivers/built-in.o: In function `amiga_serial_probe':
amiserial.c:(.init.text+0x96a): undefined reference to `__tty_alloc_driver'
amiserial.c:(.init.text+0x9c0): undefined reference to `tty_std_termios'
amiserial.c:(.init.text+0x9e6): undefined reference to `tty_set_operations'
amiserial.c:(.init.text+0xa3e): undefined reference to `tty_port_init'
amiserial.c:(.init.text+0xa5c): undefined reference to `tty_port_link_device'
amiserial.c:(.init.text+0xa6c): undefined reference to `tty_register_driver'
amiserial.c:(.init.text+0xb4a): undefined reference to `tty_unregister_driver'
amiserial.c:(.init.text+0xb58): undefined reference to `tty_port_destroy'
amiserial.c:(.init.text+0xb64): undefined reference to `put_tty_driver'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
drivers/net/ethernet/cirrus/cs89x0.c: In function ‘cs89x0_ioport_probe’:
drivers/net/ethernet/cirrus/cs89x0.c:1629: error: implicit declaration of function ‘ioport_unmap’
Add the missing ioport_unmap() implementation, and convert ioport_map()
from a macro to a static inline function while we're at it (both copied
from asm-generic).
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
If CONFIG_BLOCK=n:
arch/m68k/atari/stram.c:44: error: variable ‘stram_pool’ has initializer but incomplete type
arch/m68k/atari/stram.c:45: error: unknown field ‘name’ specified in initializer
arch/m68k/atari/stram.c:46: warning: excess elements in struct initializer
arch/m68k/atari/stram.c:46: warning: (near initialization for ‘stram_pool’)
arch/m68k/atari/stram.c: In function ‘atari_stram_reserve_pages’:
arch/m68k/atari/stram.c:97: error: invalid use of undefined type ‘struct resource’
...
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The nohz full code needs irq work to trigger its own interrupt so that
the subsystem can work even when the tick is stopped.
Lets introduce arch_irq_work_has_interrupt() that archs can override to
tell about their support for this ability.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
New system call depends on crypto. As it did not have a separate config
option, CONFIG_KEXEC was modified to select CRYPTO and CRYPTO_SHA256.
But now previous patch introduced a new config option for new syscall.
So CONFIG_KEXEC does not require crypto. Remove that dependency.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull arch signal handling cleanup from Richard Weinberger:
"This patch series moves all remaining archs to the get_signal(),
signal_setup_done() and sigsp() functions.
Currently these archs use open coded variants of the said functions.
Further, unused parameters get removed from get_signal_to_deliver(),
tracehook_signal_handler() and signal_delivered().
At the end of the day we save around 500 lines of code."
* 'signal-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/misc: (43 commits)
powerpc: Use sigsp()
openrisc: Use sigsp()
mn10300: Use sigsp()
mips: Use sigsp()
microblaze: Use sigsp()
metag: Use sigsp()
m68k: Use sigsp()
m32r: Use sigsp()
hexagon: Use sigsp()
frv: Use sigsp()
cris: Use sigsp()
c6x: Use sigsp()
blackfin: Use sigsp()
avr32: Use sigsp()
arm64: Use sigsp()
arc: Use sigsp()
sas_ss_flags: Remove nested ternary if
Rip out get_signal_to_deliver()
Clean up signal_delivered()
tracehook_signal_handler: Remove sig, info, ka and regs
...
Load purgatory code in RAM and relocate it based on the location.
Relocation code has been inspired by module relocation code and purgatory
relocation code in kexec-tools.
Also compute the checksums of loaded kexec segments and store them in
purgatory.
Arch independent code provides this functionality so that arch dependent
bootloaders can make use of it.
Helper functions are provided to get/set symbol values in purgatory which
are used by bootloaders later to set things like stack and entry point of
second kernel etc.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: WANG Chao <chaowang@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch set consists of the usual driver updates (ufs, storvsc, pm8001
hpsa). It also has removal of the user space target driver code (everyone is
using LIO now), a partial PCI MSI-X update, more multi-queue updates,
conversion to 64 bit LUNs (so we could theoretically cope with any LUN
returned by a device) and placeholder support for the ZBC device type (Shingle
drives), plus an assortment of minor updates and bug fixes.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJT4mS9AAoJEDeqqVYsXL0Mq34H/2AeXiM8GEVO3PIsBtF3TFZ9
poJvAyb8t//+VwAIVLHU9wrssIrIcyvNQmNHH/InGt5rOaXwGQRsnEc73bBtot4b
aC1t+hAnp2Ddvu6phmyUg7iY2GmQhAoZmeaj7krGIu2XgtLGiPg26eSsgk4Yv/U9
cuULEuOc/UnTj3w5VK8SvpyXMybVF6oQhSrS1slOglfFwPTlTI/NHU9xo7Wc3qHT
VifHXNphIvye5EH8zwtKX5p8qCrFW0pevJwyfPz7Hp2CTA9XYKx3SoeOh+n9F9ez
udBBggg7Vb1tb4mPKUoZ78UrtCVdFSCmesBU/RJe7cIh8daKaO5MVr3WPSx2JhM=
=yGai
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This patch set consists of the usual driver updates (ufs, storvsc,
pm8001 hpsa). It also has removal of the user space target driver
code (everyone is using LIO now), a partial PCI MSI-X update, more
multi-queue updates, conversion to 64 bit LUNs (so we could
theoretically cope with any LUN returned by a device) and placeholder
support for the ZBC device type (Shingle drives), plus an assortment
of minor updates and bug fixes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (143 commits)
scsi: do not issue SCSI RSOC command to Promise Vtrak E610f
vmw_pvscsi: Use pci_enable_msix_exact() instead of pci_enable_msix()
pm8001: Fix invalid return when request_irq() failed
lpfc: Remove superfluous call to pci_disable_msix()
isci: Use pci_enable_msix_exact() instead of pci_enable_msix()
bfa: Use pci_enable_msix_exact() instead of pci_enable_msix()
bfa: Cleanup bfad_setup_intr() function
bfa: Do not call pci_enable_msix() after it failed once
fnic: Use pci_enable_msix_exact() instead of pci_enable_msix()
scsi: use short driver name for per-driver cmd slab caches
scsi_debug: support scsi-mq, queues and locks
Drivers: add blist flags
scsi: ufs: fix endianness sparse warnings
scsi: ufs: make undeclared functions static
bnx2i: Update driver version to 2.7.10.1
pm8001: fix a memory leak in nvmd_resp
pm8001: fix update_flash
pm8001: fix a memory leak in flash_update
pm8001: Cleaning up uninitialized variables
pm8001: Fix to remove null pointer checks that could never happen
...
Pull m68knommu fixes from Greg Ungerer:
"Just a couple of small fixes. Fix definition of page_to_phys() and
remove unecesary prototype of kobjsize()"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: Remove unnecessary prototype for kobjsize()
m68knommu: Correct page_to_phys when PAGE_OFFSET is non-zero.
Pull locking updates from Ingo Molnar:
"The main changes in this cycle are:
- big rtmutex and futex cleanup and robustification from Thomas
Gleixner
- mutex optimizations and refinements from Jason Low
- arch_mutex_cpu_relax() removal and related cleanups
- smaller lockdep tweaks"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
arch, locking: Ciao arch_mutex_cpu_relax()
locking/lockdep: Only ask for /proc/lock_stat output when available
locking/mutexes: Optimize mutex trylock slowpath
locking/mutexes: Try to acquire mutex only if it is unlocked
locking/mutexes: Delete the MUTEX_SHOW_NO_WAITER macro
locking/mutexes: Correct documentation on mutex optimistic spinning
rtmutex: Make the rtmutex tester depend on BROKEN
futex: Simplify futex_lock_pi_atomic() and make it more robust
futex: Split out the first waiter attachment from lookup_pi_state()
futex: Split out the waiter check from lookup_pi_state()
futex: Use futex_top_waiter() in lookup_pi_state()
futex: Make unlock_pi more robust
rtmutex: Avoid pointless requeueing in the deadlock detection chain walk
rtmutex: Cleanup deadlock detector debug logic
rtmutex: Confine deadlock logic to futex
rtmutex: Simplify remove_waiter()
rtmutex: Document pi chain walk
rtmutex: Clarify the boost/deboost part
rtmutex: No need to keep task ref for lock owner check
rtmutex: Simplify and document try_to_take_rtmutex()
...
In the file sun3_pgalloc.h we should remove #define_KERNPG_TABLE equals 0
as this define statement hasn't been used since kernel verison 2.5.18 and
is now no longer needed.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Because of the removal of the scsi_tgt kernel module, the kbuild variables
CONFIG_SCSI_TGT, CONFIG_SCSI_SRP_TGT_ATTRS and CONFIG_SCSI_FC_TGT_ATTRS
are obsolete. This patch removes these variables. This patch is the result
of the following command:
find -name '*defconfig' | while read f; do grep -vwE 'CONFIG_SCSI_TGT|CONFIG_SCSI_SRP_TGT_ATTRS|CONFIG_SCSI_FC_TGT_ATTRS|CONFIG_SRP' $f >/tmp/t && mv /tmp/t $f; done
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
The arch_mutex_cpu_relax() function, introduced by 34b133f, is
hacky and ugly. It was added a few years ago to address the fact
that common cpu_relax() calls include yielding on s390, and thus
impact the optimistic spinning functionality of mutexes. Nowadays
we use this function well beyond mutexes: rwsem, qrwlock, mcs and
lockref. Since the macro that defines the call is in the mutex header,
any users must include mutex.h and the naming is misleading as well.
This patch (i) renames the call to cpu_relax_lowlatency ("relax, but
only if you can do it with very low latency") and (ii) defines it in
each arch's asm/processor.h local header, just like for regular cpu_relax
functions. On all archs, except s390, cpu_relax_lowlatency is simply cpu_relax,
and thus we can take it out of mutex.h. While this can seem redundant,
I believe it is a good choice as it allows us to move out arch specific
logic from generic locking primitives and enables future(?) archs to
transparently define it, similarly to System Z.
Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Bharat Bhushan <r65777@freescale.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chen Liqin <liqin.linux@gmail.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: David Howells <dhowells@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Cc: Dominik Dingel <dingel@linux.vnet.ibm.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Joe Perches <joe@perches.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Joseph Myers <joseph@codesourcery.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Nicolas Pitre <nico@linaro.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Qiaowei Ren <qiaowei.ren@intel.com>
Cc: Rafael Wysocki <rafael.j.wysocki@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Steven Rostedt <srostedt@redhat.com>
Cc: Stratos Karafotis <stratosk@semaphore.gr>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vasily Kulikov <segoon@openwall.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Vineet Gupta <Vineet.Gupta1@synopsys.com>
Cc: Waiman Long <Waiman.Long@hp.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: adi-buildroot-devel@lists.sourceforge.net
Cc: linux390@de.ibm.com
Cc: linux-alpha@vger.kernel.org
Cc: linux-am33-list@redhat.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-c6x-dev@linux-c6x.org
Cc: linux-cris-kernel@axis.com
Cc: linux-hexagon@vger.kernel.org
Cc: linux-ia64@vger.kernel.org
Cc: linux@lists.openrisc.net
Cc: linux-m32r-ja@ml.linux-m32r.org
Cc: linux-m32r@ml.linux-m32r.org
Cc: linux-m68k@lists.linux-m68k.org
Cc: linux-metag@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-parisc@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-s390@vger.kernel.org
Cc: linux-sh@vger.kernel.org
Cc: linux-xtensa@linux-xtensa.org
Cc: sparclinux@vger.kernel.org
Link: http://lkml.kernel.org/r/1404079773.2619.4.camel@buesod1.americas.hpqcorp.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
My enhancement to store the initial mapping size for later reuse in commit
486df8bc46 ("m68k: Increase initial mapping
to 8 or 16 MiB if possible") broke booting on machines where RAM doesn't
start at address zero.
Use pc-relative addressing to fix this.
Reported-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Andreas Schwab <schwab@linux-m68k.org>
The prototype for kobjsize() is already defined in linux/mm.h which is
included where kobjsize() is used.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
The definition of page_to_phys for nommu produces an incorrect value when
PAGE_OFFSET is non-zero. The nommu version of page_to_pfn works correctly
for non-zero PAGE_OFFSET, so use that instead.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
It has no users and it doesn't look useful. I do not know why/when it was
introduced, I can't even find any user in the git history.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull m68knommu updates from Greg Ungerer:
"Nothing too big, just a handfull of small changes.
A couple of dragonball fixes, coldfire qspi cleanup and fixes, and
some coldfire gpio cleanup, fixes and extensions"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: Implement gpio support for m54xx.
m68knommu: Make everything thats not exported, static.
m68knommu: setting the gpio data direction register to output doesn't dependent upon the value to output!
m68knommu: add to_irq function so we can map gpios to external interrupts.
m68knommu: qspi declutter.
m68knommu: Fix the 5249/525x qspi base address.
m68knommu: Add qspi clk for Coldfire SoCs without real clks.
m68k: fix a compiler warning when building for DragonBall
m68knommu: Fix mach_sched_init for EZ and VZ DragonBall chips
This patch also fixes some checkpatch warnings
This is untested
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
no level printk converted to pr_info
This is untested
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
-no level printk converted to pr_warn/pr_info
-fixed a small identation problem
This is untested
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
If the size of the first memory chunk is at least 8 or 16 MiB increase the
initial mapping to 8 resp. 16 MiB instead of 4 MiB.
This makes it possible to
1. Map more memory in the first node without running out of space for the
page tables,
2. Boot kernels that don't fit in 4 MiB (e.g. multi_defconfig).
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
- Add support for 8 MiB,
- Store initial mapping size in head.S for later reuse,
- Add comment about large kernels.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fix SCC initialization for Atari as was previously fixed for Mac. It's
probably not practical to share more code but some attempt is made to
align the Mac and Atari variants.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
In a multi-platform kernel binary we only need one early console instance.
The difficulty here is that the common early console is started by
early_param(), whereas the MVME16x instance is started later by
config_mvme16x(). That means some interrupt setup must be done earlier.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Stephen N Chivers <schivers@csc.com.au>
[Geert] Tag debug_cons_write() with __ref to kill section mismatch warning
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Make the boot console available to more m68k platforms by leveraging
the head.S debug console.
The boot console is enabled by the "earlyprintk" command line argument
which is how most other architectures do this.
This is a change of behaviour for the Mac but does not negatively impact
the common use-case which is not debugging.
This is also a change of behaviour for other platforms because it means
the serial port stays quiet when CONFIG_EARLY_PRINTK is not enabled. This
is also an improvement for the common use-case.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Stephen N Chivers <schivers@csc.com.au>
[Geert: CONSOLE_DEBUG should depend on CONFIG_FONT_SUPPORT]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Code subject to #ifdef CONSOLE is made more generic, as was apparently
intended by the original author.
Remove console_put_stats() routine. If it should be somehow useful, it
should also be useful on platforms without framebuffer debug logging. The
present implementation is only built #if defined CONFIG_MAC && defined
CONSOLE even though puts() works everywhere.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Stephen N Chivers <schivers@csc.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
With the kernel loaded to FastRAM (TT-RAM), none of the ST-RAM
address range is mapped by init_mem, and ST-RAM is not accessible
through the normal allocation pathways as a result.
Implement ST-RAM pool allocation to be based on physical addresses
always (it already was when the kernel was loaded in ST-RAM).
Return kernel virtual addresses as per normal.
The current test for the kernel residing in ST-RAM always returns
true. Use the bootinfo memory chunk order instead - with the kernel
in FastRAM, ST-RAM (phys. 0x0) is not the first chunk.
In case the kernel is running from FastRAM, delay mapping of ST-RAM
pool until after mem_init.
Provide helper functions for those users of ST-RAM that need
to be aware of the backing physical addresses.
Kudos to Geert for his hints on getting this started.
Signed-off-by: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Move the check for the QSPI config option inside the function body. If the
option is not enabled, the compiler will optimize away the empty function
body so we can remove the other check for the config option.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Use the correct base address for the QSPI module on the 5249/525x.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Since we now have fake clks on devices without real clocks, we need clks
defined for qspi for the qspi driver to work on those devices.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
In file included from arch/m68k/kernel/setup.c:4:0:
arch/m68k/kernel/setup_no.c:70:0: warning: "CPU_NAME" redefined [enabled by default]
#define CPU_NAME "MC68VZ328"
^
arch/m68k/kernel/setup_no.c:61:0: note: this is the location of the previous definition
#define CPU_NAME "MC68000"
^
Signed-off-by: Daniel Palmer <danieruru@gmail.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
