Implement COALESCE_SET netlink request to set coalescing parameters of
a network device. These are traditionally set with ETHTOOL_SCOALESCE ioctl
request. This commit adds only support for device coalescing parameters,
not per queue coalescing parameters.
Like the ioctl implementation, the generic ethtool code checks if only
supported parameters are modified; if not, first offending attribute is
reported using extack.
v2: fix alignment (whitespace only)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement COALESCE_GET request to get coalescing parameters of a network
device. These are traditionally available via ETHTOOL_GCOALESCE ioctl
request. This commit adds only support for device coalescing parameters,
not per queue coalescing parameters.
Omit attributes with zero values unless they are declared as supported
(i.e. the corresponding bit in ethtool_ops::supported_coalesce_params is
set).
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew noticed that some handlers for *_SET commands leak a netdev
reference if required ethtool_ops callbacks do not exist. One of them is
ethnl_set_privflags(), a simple reproducer would be e.g.
ip link add veth1 type veth peer name veth2
ethtool --set-priv-flags veth1 foo on
ip link del veth1
Make sure dev_put() is called when ethtool_ops check fails.
Fixes: f265d79959 ("ethtool: set device private flags with PRIVFLAGS_SET request")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring says:
====================
net: ipv6: add rpl source routing
This patch series will add handling for RPL source routing handling
and insertion (implement as lwtunnel)! I did an example prototype
implementation in rpld for using this implementation in non-storing mode:
https://github.com/linux-wpan/rpld/tree/nonstoring_mode
I will also present a talk at netdev about it:
https://netdevconf.info/0x14/session.html?talk-extend-segment-routing-for-RPL
In receive handling I add handling for IPIP encapsulation as RFC6554
describes it as possible. For reasons I didn't implemented it yet for
generating such packets because I am not really sure how/when this
should happen. So far I understand there exists a draft yet which
describes the cases (inclusive a Hop-by-Hop option which we also not
support yet).
https://tools.ietf.org/html/draft-ietf-roll-useofrplinfo-35
This is just the beginning to start implementation everything for yet,
step by step. It works for my use cases yet to have it running on a
6LOWPAN _only_ network.
I have some patches for iproute2 as well.
A sidenote: I check on local addresses if they are part of segment
routes, this is just to avoid stupid settings. A use can add addresses
afterwards what I cannot control anymore but then it's users fault to
make such thing. The receive handling checks for this as well which is
required by RFC6554, so the next hops or when it comes back should drop
it anyway.
To make this possible I added functionality to pass the net structure to
the build_state of lwtunnel (I hope I caught all lwtunnels).
Another sidenote: I set the headroom value to 0 as I figured out it will
break on interfaces with IPv6 min mtu if set to non zero for tunnels on
L3.
- Alex
changes since v3:
- use parse_nested which isn't deprecated - Thanks David Ahern
- change to return -1 instead errno in exthdr handling to unify
error code
- change function name from ipv6_rpl_srh_decompress_size to
ipv6_rpl_srh_size
changes since v2:
- add additional segdata length in lwtunnel build_state
- fix build_state patch by not catching one inline noop function
if LWTUNNEL is disabled
Alexander Aring (5):
include: uapi: linux: add rpl sr header definition
addrconf: add functionality to check on rpl requirements
net: ipv6: add support for rpl sr exthdr
net: add net available in build_state
net: ipv6: add rpl sr tunnel
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds functionality to configure routes for RPL source routing
functionality. There is no IPIP functionality yet implemented which can
be added later when the cases when to use IPv6 encapuslation comes more
clear.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The build_state callback of lwtunnel doesn't contain the net namespace
structure yet. This patch will add it so we can check on specific
address configuration at creation time of rpl source routes.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds rpl source routing receive handling. Everything works
only if sysconf "rpl_seg_enabled" and source routing is enabled. Mostly
the same behaviour as IPv6 segmentation routing. To handle compression
and uncompression a rpl.c file is created which contains the necessary
functionality. The receive handling will also care about IPv6
encapsulated so far it's specified as possible nexthdr in RFC 6554.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a functionality to addrconf to check on a specific RPL
address configuration. According to RFC 6554:
To detect loops in the SRH, a router MUST determine if the SRH
includes multiple addresses assigned to any interface on that
router. If such addresses appear more than once and are separated by
at least one address not assigned to that router.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a uapi header for rpl struct definition. The segments
data can be accessed over rpl_segaddr or rpl_segdata macros. In case of
compri and compre is zero the segment data is not compressed and can be
accessed by rpl_segaddr. In the other case the compressed data can be
accessed by rpl_segdata and interpreted as byte array.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mat Martineau says:
====================
Multipath TCP part 3: Multiple subflows and path management
v2 -> v3: Remove 'inline' in .c files, fix uapi bit macros, and rebase.
v1 -> v2: Rebase on current net-next, fix for netlink limit setting,
and update .gitignore for selftest.
This patch set allows more than one TCP subflow to be established and
used for a multipath TCP connection. Subflows are added to an existing
connection using the MP_JOIN option during the 3-way handshake. With
multiple TCP subflows available, sent data is now stored in the MPTCP
socket so it may be retransmitted on any TCP subflow if there is no
DATA_ACK before a timeout. If an MPTCP-level timeout occurs, data is
retransmitted using an available subflow. Storing this sent data
requires the addition of memory accounting at the MPTCP level, which was
previously delegated to the single subflow. Incoming DATA_ACKs now free
data from the MPTCP-level retransmit buffer.
IP addresses available for new subflow connections can now be advertised
and received with the ADD_ADDR option, and the corresponding REMOVE_ADDR
option likewise advertises that an address is no longer available.
The MPTCP path manager netlink interface has commands to set in-kernel
limits for the number of concurrent subflows and control the
advertisement of IP addresses between peers.
To track and debug MPTCP connections there are new MPTCP MIB counters,
and subflow context can be requested using inet_diag. The MPTCP
self-tests now validate multiple-subflow operation and the netlink path
manager interface.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the pm netlink to configure the creation of several
subflows, and verify that via MIB counters.
Update the mptcp_connect program to allow reliable MP_JOIN
handshake even on small data file
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces basic self-tests for the PM netlink,
checking the basic APIs and possible exceptional
values.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose a new netlink family to userspace to control the PM, setting:
- list of local addresses to be signalled.
- list of local addresses used to created subflows.
- maximum number of add_addr option to react
When the msk is fully established, the PM netlink attempts to
announce the 'signal' list via the ADD_ADDR option. Since we
currently lack the ADD_ADDR echo (and related event) only the
first addr is sent.
After exhausting the 'announce' list, the PM tries to create
subflow for each addr in 'local' list, waiting for each
connection to be completed before attempting the next one.
Idea is to add an additional PM hook for ADD_ADDR echo, to allow
the PM netlink announcing multiple addresses, in sequence.
Co-developed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Exported via same /proc file as the Linux TCP MIB counters, so "netstat -s"
or "nstat" will show them automatically.
The MPTCP MIB counters are allocated in a distinct pcpu area in order to
avoid bloating/wasting TCP pcpu memory.
Counters are allocated once the first MPTCP socket is created in a
network namespace and free'd on exit.
If no sockets have been allocated, all-zero mptcp counters are shown.
The MIB counter list is taken from the multipath-tcp.org kernel, but
only a few counters have been picked up so far. The counter list can
be increased at any time later on.
v2 -> v3:
- remove 'inline' in foo.c files (David S. Miller)
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add ulp-specific diagnostic functions, so that subflow information can be
dumped to userspace programs like 'ss'.
v2 -> v3:
- uapi: use bit macros appropriate for userspace
Co-developed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On timeout event, schedule a work queue to do the retransmission.
Retransmission code closely resembles the sendmsg() implementation and
re-uses mptcp_sendmsg_frag, providing a dummy msghdr - for flags'
sake - and peeking the relevant dfrag from the rtx head.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will simplify mptcp-level retransmission implementation
in the next patch. If dfrag is provided by the caller, skip
kernel space memory allocation and use data and metadata
provided by the dfrag itself.
Because a peer could ack data at TCP level but refrain from
sending mptcp-level ACKs, we could grow the mptcp socket
backlog indefinitely.
We should thus block mptcp_sendmsg until the peer has acked some of the
sent data.
In order to be able to do so, increment the mptcp socket wmem_queued
counter on memory allocation and decrement it when releasing the memory
on mptcp-level ack reception.
Because TCP performns sndbuf auto-tuning up to tcp_wmem_max[2], make
this the mptcp sk_sndbuf limit.
In the future we could add experiment with autotuning as TCP does in
tcp_sndbuf_expand().
v2 -> v3:
- remove 'inline' in foo.c files (David S. Miller)
Co-developed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After adding wmem accounting for the mptcp socket we could get
into a situation where the mptcp socket can't transmit more data,
and mptcp_clean_una doesn't reduce wmem even if snd_una has advanced
because it currently will only remove entire dfrags.
Allow advancing the dfrag head sequence and reduce wmem,
even though this isn't correct (as we can't release the page).
Because we will soon block on mptcp sk in case wmem is too large,
call sk_stream_write_space() in case we reduced the backlog so
userspace task blocked in sendmsg or poll will be woken up.
This isn't an issue if the send buffer is large, but it is when
SO_SNDBUF is used to reduce it to a lower value.
Note we can still get a deadlock for low SO_SNDBUF values in
case both sides of the connection write to the socket: both could
be blocked due to wmem being too small -- and current mptcp stack
will only increment mptcp ack_seq on recv.
This doesn't happen with the selftest as it uses poll() and
will always call recv if there is data to read.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Charge the data on the rtx queue to the master MPTCP socket, too.
Such memory in uncharged when the data is acked/dequeued.
Also account mptcp sockets inuse via a protocol specific pcpu
counter.
Co-developed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The timer will be used to schedule retransmission. It's
frequency is based on the current subflow RTO estimation and
is reset on every una_seq update
The timer is clearer for good by __mptcp_clear_xmit()
Also clean MPTCP rtx queue before each transmission.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep the send page fragment on an MPTCP level retransmission queue.
The queue entries are allocated inside the page frag allocator,
acquiring an additional reference to the page for each list entry.
Also switch to a custom page frag refill function, to ensure that
the current page fragment can always host an MPTCP rtx queue entry.
The MPTCP rtx queue is flushed at disconnect() and close() time
Note that now we need to call __mptcp_init_sock() regardless of mptcp
enable status, as the destructor will try to walk the rtx_queue.
v2 -> v3:
- remove 'inline' in foo.c files (David S. Miller)
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So that we keep per unacked sequence number consistent; since
we update per msk data, use an atomic64 cmpxchg() to protect
against concurrent updates from multiple subflows.
Initialize the snd_una at connect()/accept() time.
Co-developed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fill in more path manager functionality by adding a worker function and
modifying the related stub functions to schedule the worker.
Co-developed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Peter Krystad <peter.krystad@linux.intel.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Subflow creation may be initiated by the path manager when
the primary connection is fully established and a remote
address has been received via ADD_ADDR.
Create an in-kernel sock and use kernel_connect() to
initiate connection.
Passive sockets can't acquire the mptcp socket lock at
subflow creation time, so an additional list protected by
a new spinlock is used to track the MPJ subflows.
Such list is spliced into conn_list tail every time the msk
socket lock is acquired, so that it will not interfere
with data flow on the original connection.
Data flow and connection failover not addressed by this commit.
Co-developed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Co-developed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Peter Krystad <peter.krystad@linux.intel.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Process the MP_JOIN option in a SYN packet with the same flow
as MP_CAPABLE but when the third ACK is received add the
subflow to the MPTCP socket subflow list instead of adding it to
the TCP socket accept queue.
The subflow is added at the end of the subflow list so it will not
interfere with the existing subflows operation and no data is
expected to be transmitted on it.
Co-developed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Peter Krystad <peter.krystad@linux.intel.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add enough of a path manager interface to allow sending of ADD_ADDR
when an incoming MPTCP connection is created. Capable of sending only
a single IPv4 ADD_ADDR option. The 'pm_data' element of the connection
sock will need to be expanded to handle multiple interfaces and IPv6.
Partial processing of the incoming ADD_ADDR is included so the path
manager notification of that event happens at the proper time, which
involves validating the incoming address information.
This is a skeleton interface definition for events generated by
MPTCP.
Co-developed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Co-developed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Co-developed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Peter Krystad <peter.krystad@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add handling for sending and receiving the ADD_ADDR, ADD_ADDR6,
and RM_ADDR suboptions.
Co-developed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Peter Krystad <peter.krystad@linux.intel.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent commit e893768179 ("devlink: prepare to support region
operations") used the region_cr_space_str and region_fw_health_str
variables as initializers for the devlink_region_ops structures.
This can result in compiler errors:
drivers/net/ethernet/mellanox//mlx4/crdump.c:45:10: error: initializer
element is not constant
.name = region_cr_space_str,
^
drivers/net/ethernet/mellanox//mlx4/crdump.c:45:10: note: (near
initialization for ‘region_cr_space_ops.name’)
drivers/net/ethernet/mellanox//mlx4/crdump.c:50:10: error: initializer
element is not constant
.name = region_fw_health_str,
The variables were made to be "const char * const", indicating that both
the pointer and data were constant. This was enough to resolve this on
recent GCC (gcc (GCC) 9.2.1 20190827 (Red Hat 9.2.1-1) for this author).
Unfortunately this is not enough for older compilers to realize that the
variable can be treated as a constant expression.
Fix this by introducing macros for the string and use those instead of
the variable name in the region ops structures.
Reported-by: tanhuazhong <tanhuazhong@huawei.com>
Fixes: e893768179 ("devlink: prepare to support region operations")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The devlink-region.rst and ice-region.rst documentation files wrapped
some lines within shell code blocks due to being longer than 80 lines.
It was pointed out during review that wrapping these lines shouldn't be
done. Fix these two rST files and remove the line wrapping on these
shell command examples.
Reported-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the mt7530 switch driver to use the finalised link
parameters in mac_link_up() rather than the parameters in mac_config().
Signed-off-by: René van Dorst <opensource@vdorst.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like the P/Q/R/S series supports some more counters,
generically named "Ethernet statistics counter", which we were not
printing. Add them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable the L3 driver's IPv4 address notifier to watch for events on qeth
devices that have been moved into a net namespace. We need to program
those IPs into the HW just as usual, otherwise inbound traffic won't
flow.
Fixes: 6133fb1aa1 ("[NETNS]: Disable inetaddr notifiers in namespaces other than initial.")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SKB_SGO_CB_OFFSET should be SKB_GSO_CB_OFFSET which means the
offset of the GSO in skb cb. This patch fixes the typo.
Fixes: 9207f9d45b ("net: preserve IP control block during GSO segmentation")
Signed-off-by: Cambda Zhu <cambda@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling queue_delayed_work concurrently with
destroy_workqueue might race to an unexpected outcome -
scheduled task after wq is destroyed or other resources
(like ptt_pool) are freed (yields NULL pointer dereference).
cancel_delayed_work prevents the race by cancelling
the timer triggered for scheduling a new task.
Fixes: 59ccf86fe ("qed: Add driver infrastucture for handling mfw requests")
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Yuval Basson <ybason@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
page pool API can be useful for non-DMA cases like
xen-netfront driver so let's allow to pass zero flags to
page pool flags.
v2: check DMA direction only if PP_FLAG_DMA_MAP is set
Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For historical reasons, there are several timestamping selftest targets
in selftests/networking/timestamping. Move them to the standard
directory for networking tests: selftests/net.
Signed-off-by: Jian Yang <jianyang@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now a PHY-fixup in mach-imx set our rgmii timing correctly. For
the PHY KSZ9131 there is no PHY-fixup in mach-imx. To support this PHY
too, use rgmii-id.
For the now used KSZ9031 nothing will change, as rgmii-id is only
implemented and supported by the KSZ9131.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ9131 provides DLL controlled delays on RXC and TXC lines. This
patch makes use of those delays. The information which delays should
be enabled or disabled comes from the interface names, documented in
ethernet-controller.yaml:
rgmii: Disable RXC and TXC delays
rgmii-id: Enable RXC and TXC delays
rgmii-txid: Enable only TXC delay, disable RXC delay
rgmii-rxid: Enable onlx RXC delay, disable TXC delay
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds new netlink attribute to allow a user to (optionally)
specify the desired offload mode immediately upon MACSec link creation.
Separate iproute patch will be required to support this from user space.
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge vm fixes from Andrew Morton:
"5 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm/sparse: fix kernel crash with pfn_section_valid check
mm: fork: fix kernel_stack memcg stats for various stack implementations
hugetlb_cgroup: fix illegal access to memory
drivers/base/memory.c: indicate all memory blocks as removable
mm/swapfile.c: move inode_lock out of claim_swapfile
actually return nanoseconds and not the virtual clock value which
increments at 10e7 HZ (100ns).
-----BEGIN PGP SIGNATURE-----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=qZa/
-----END PGP SIGNATURE-----
Merge tag 'timers-urgent-2020-03-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Thomas Gleixner:
"A single fix for the Hyper-V clocksource driver to make sched clock
actually return nanoseconds and not the virtual clock value which
increments at 10e7 HZ (100ns)"
* tag 'timers-urgent-2020-03-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/hyper-v: Make sched clock return nanoseconds correctly
-----BEGIN PGP SIGNATURE-----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=s1UQ
-----END PGP SIGNATURE-----
Merge tag 'irq-urgent-2020-03-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Thomas Gleixner:
"A single bugfix to prevent reference leaks in irq affinity notifiers"
* tag 'irq-urgent-2020-03-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Fix reference leaks on irq affinity notifiers
Fix the crash like this:
BUG: Kernel NULL pointer dereference on read at 0x00000000
Faulting instruction address: 0xc000000000c3447c
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
CPU: 11 PID: 7519 Comm: lt-ndctl Not tainted 5.6.0-rc7-autotest #1
...
NIP [c000000000c3447c] vmemmap_populated+0x98/0xc0
LR [c000000000088354] vmemmap_free+0x144/0x320
Call Trace:
section_deactivate+0x220/0x240
__remove_pages+0x118/0x170
arch_remove_memory+0x3c/0x150
memunmap_pages+0x1cc/0x2f0
devm_action_release+0x30/0x50
release_nodes+0x2f8/0x3e0
device_release_driver_internal+0x168/0x270
unbind_store+0x130/0x170
drv_attr_store+0x44/0x60
sysfs_kf_write+0x68/0x80
kernfs_fop_write+0x100/0x290
__vfs_write+0x3c/0x70
vfs_write+0xcc/0x240
ksys_write+0x7c/0x140
system_call+0x5c/0x68
The crash is due to NULL dereference at
test_bit(idx, ms->usage->subsection_map);
due to ms->usage = NULL in pfn_section_valid()
With commit d41e2f3bd5 ("mm/hotplug: fix hot remove failure in
SPARSEMEM|!VMEMMAP case") section_mem_map is set to NULL after
depopulate_section_mem(). This was done so that pfn_page() can work
correctly with kernel config that disables SPARSEMEM_VMEMMAP. With that
config pfn_to_page does
__section_mem_map_addr(__sec) + __pfn;
where
static inline struct page *__section_mem_map_addr(struct mem_section *section)
{
unsigned long map = section->section_mem_map;
map &= SECTION_MAP_MASK;
return (struct page *)map;
}
Now with SPASEMEM_VMEMAP enabled, mem_section->usage->subsection_map is
used to check the pfn validity (pfn_valid()). Since section_deactivate
release mem_section->usage if a section is fully deactivated,
pfn_valid() check after a subsection_deactivate cause a kernel crash.
static inline int pfn_valid(unsigned long pfn)
{
...
return early_section(ms) || pfn_section_valid(ms, pfn);
}
where
static inline int pfn_section_valid(struct mem_section *ms, unsigned long pfn)
{
int idx = subsection_map_index(pfn);
return test_bit(idx, ms->usage->subsection_map);
}
Avoid this by clearing SECTION_HAS_MEM_MAP when mem_section->usage is
freed. For architectures like ppc64 where large pages are used for
vmmemap mapping (16MB), a specific vmemmap mapping can cover multiple
sections. Hence before a vmemmap mapping page can be freed, the kernel
needs to make sure there are no valid sections within that mapping.
Clearing the section valid bit before depopulate_section_memap enables
this.
[aneesh.kumar@linux.ibm.com: add comment]
Link: http://lkml.kernel.org/r/20200326133235.343616-1-aneesh.kumar@linux.ibm.comLink: http://lkml.kernel.org/r/20200325031914.107660-1-aneesh.kumar@linux.ibm.com
Fixes: d41e2f3bd5 ("mm/hotplug: fix hot remove failure in SPARSEMEM|!VMEMMAP case")
Reported-by: Sachin Sant <sachinp@linux.vnet.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Tested-by: Sachin Sant <sachinp@linux.vnet.ibm.com>
Reviewed-by: Baoquan He <bhe@redhat.com>
Reviewed-by: Wei Yang <richard.weiyang@gmail.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Depending on CONFIG_VMAP_STACK and the THREAD_SIZE / PAGE_SIZE ratio the
space for task stacks can be allocated using __vmalloc_node_range(),
alloc_pages_node() and kmem_cache_alloc_node().
In the first and the second cases page->mem_cgroup pointer is set, but
in the third it's not: memcg membership of a slab page should be
determined using the memcg_from_slab_page() function, which looks at
page->slab_cache->memcg_params.memcg . In this case, using
mod_memcg_page_state() (as in account_kernel_stack()) is incorrect:
page->mem_cgroup pointer is NULL even for pages charged to a non-root
memory cgroup.
It can lead to kernel_stack per-memcg counters permanently showing 0 on
some architectures (depending on the configuration).
In order to fix it, let's introduce a mod_memcg_obj_state() helper,
which takes a pointer to a kernel object as a first argument, uses
mem_cgroup_from_obj() to get a RCU-protected memcg pointer and calls
mod_memcg_state(). It allows to handle all possible configurations
(CONFIG_VMAP_STACK and various THREAD_SIZE/PAGE_SIZE values) without
spilling any memcg/kmem specifics into fork.c .
Note: This is a special version of the patch created for stable
backports. It contains code from the following two patches:
- mm: memcg/slab: introduce mem_cgroup_from_obj()
- mm: fork: fix kernel_stack memcg stats for various stack implementations
[guro@fb.com: introduce mem_cgroup_from_obj()]
Link: http://lkml.kernel.org/r/20200324004221.GA36662@carbon.dhcp.thefacebook.com
Fixes: 4d96ba3530 ("mm: memcg/slab: stop setting page->mem_cgroup pointer for slab pages")
Signed-off-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Bharata B Rao <bharata@linux.ibm.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20200303233550.251375-1-guro@fb.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This appears to be a mistake in commit faced7e080 ("mm: hugetlb
controller for cgroups v2").
Essentially that commit does a hugetlb_cgroup_from_counter assuming that
page_counter_try_charge has initialized counter.
But if that has failed then it seems will not initialize counter, so
hugetlb_cgroup_from_counter(counter) ends up pointing to random memory,
causing kasan to complain.
The solution is to simply use 'h_cg', instead of
hugetlb_cgroup_from_counter(counter), since that is a reference to the
hugetlb_cgroup anyway. After this change kasan ceases to complain.
Fixes: faced7e080 ("mm: hugetlb controller for cgroups v2")
Reported-by: syzbot+cac0c4e204952cf449b1@syzkaller.appspotmail.com
Signed-off-by: Mina Almasry <almasrymina@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Giuseppe Scrivano <gscrivan@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: David Rientjes <rientjes@google.com>
Link: http://lkml.kernel.org/r/20200313223920.124230-1-almasrymina@google.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We see multiple issues with the implementation/interface to compute
whether a memory block can be offlined (exposed via
/sys/devices/system/memory/memoryX/removable) and would like to simplify
it (remove the implementation).
1. It runs basically lockless. While this might be good for performance,
we see possible races with memory offlining that will require at
least some sort of locking to fix.
2. Nowadays, more false positives are possible. No arch-specific checks
are performed that validate if memory offlining will not be denied
right away (and such check will require locking). For example, arm64
won't allow to offline any memory block that was added during boot -
which will imply a very high error rate. Other archs have other
constraints.
3. The interface is inherently racy. E.g., if a memory block is detected
to be removable (and was not a false positive at that time), there is
still no guarantee that offlining will actually succeed. So any
caller already has to deal with false positives.
4. It is unclear which performance benefit this interface actually
provides. The introducing commit 5c755e9fd8 ("memory-hotplug: add
sysfs removable attribute for hotplug memory remove") mentioned
"A user-level agent must be able to identify which sections
of memory are likely to be removable before attempting the
potentially expensive operation."
However, no actual performance comparison was included.
Known users:
- lsmem: Will group memory blocks based on the "removable" property. [1]
- chmem: Indirect user. It has a RANGE mode where one can specify
removable ranges identified via lsmem to be offlined. However,
it also has a "SIZE" mode, which allows a sysadmin to skip the
manual "identify removable blocks" step. [2]
- powerpc-utils: Uses the "removable" attribute to skip some memory
blocks right away when trying to find some to offline+remove.
However, with ballooning enabled, it already skips this
information completely (because it once resulted in many false
negatives). Therefore, the implementation can deal with false
positives properly already. [3]
According to Nathan Fontenot, DLPAR on powerpc is nowadays no longer
driven from userspace via the drmgr command (powerpc-utils). Nowadays
it's managed in the kernel - including onlining/offlining of memory
blocks - triggered by drmgr writing to /sys/kernel/dlpar. So the
affected legacy userspace handling is only active on old kernels. Only
very old versions of drmgr on a new kernel (unlikely) might execute
slower - totally acceptable.
With CONFIG_MEMORY_HOTREMOVE, always indicating "removable" should not
break any user space tool. We implement a very bad heuristic now.
Without CONFIG_MEMORY_HOTREMOVE we cannot offline anything, so report
"not removable" as before.
Original discussion can be found in [4] ("[PATCH RFC v1] mm:
is_mem_section_removable() overhaul").
Other users of is_mem_section_removable() will be removed next, so that
we can remove is_mem_section_removable() completely.
[1] http://man7.org/linux/man-pages/man1/lsmem.1.html
[2] http://man7.org/linux/man-pages/man8/chmem.8.html
[3] https://github.com/ibm-power-utilities/powerpc-utils
[4] https://lkml.kernel.org/r/20200117105759.27905-1-david@redhat.com
Also, this patch probably fixes a crash reported by Steve.
http://lkml.kernel.org/r/CAPcyv4jpdaNvJ67SkjyUJLBnBnXXQv686BiVW042g03FUmWLXw@mail.gmail.com
Reported-by: "Scargall, Steve" <steve.scargall@intel.com>
Suggested-by: Michal Hocko <mhocko@kernel.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Nathan Fontenot <ndfont@gmail.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Cc: Robert Jennings <rcj@linux.vnet.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Karel Zak <kzak@redhat.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20200128093542.6908-1-david@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
claim_swapfile() currently keeps the inode locked when it is successful,
or the file is already swapfile (with -EBUSY). And, on the other error
cases, it does not lock the inode.
This inconsistency of the lock state and return value is quite confusing
and actually causing a bad unlock balance as below in the "bad_swap"
section of __do_sys_swapon().
This commit fixes this issue by moving the inode_lock() and IS_SWAPFILE
check out of claim_swapfile(). The inode is unlocked in
"bad_swap_unlock_inode" section, so that the inode is ensured to be
unlocked at "bad_swap". Thus, error handling codes after the locking now
jumps to "bad_swap_unlock_inode" instead of "bad_swap".
=====================================
WARNING: bad unlock balance detected!
5.5.0-rc7+ #176 Not tainted
-------------------------------------
swapon/4294 is trying to release lock (&sb->s_type->i_mutex_key) at: __do_sys_swapon+0x94b/0x3550
but there are no more locks to release!
other info that might help us debug this:
no locks held by swapon/4294.
stack backtrace:
CPU: 5 PID: 4294 Comm: swapon Not tainted 5.5.0-rc7-BTRFS-ZNS+ #176
Hardware name: ASUS All Series/H87-PRO, BIOS 2102 07/29/2014
Call Trace:
dump_stack+0xa1/0xea
print_unlock_imbalance_bug.cold+0x114/0x123
lock_release+0x562/0xed0
up_write+0x2d/0x490
__do_sys_swapon+0x94b/0x3550
__x64_sys_swapon+0x54/0x80
do_syscall_64+0xa4/0x4b0
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x7f15da0a0dc7
Fixes: 1638045c36 ("mm: set S_SWAPFILE on blockdev swap devices")
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Tested-by: Qais Youef <qais.yousef@arm.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20200206090132.154869-1-naohiro.aota@wdc.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking fixes from David Miller:
1) Fix memory leak in vti6, from Torsten Hilbrich.
2) Fix double free in xfrm_policy_timer, from YueHaibing.
3) NL80211_ATTR_CHANNEL_WIDTH attribute is put with wrong type, from
Johannes Berg.
4) Wrong allocation failure check in qlcnic driver, from Xu Wang.
5) Get ks8851-ml IO operations right, for real this time, from Marek
Vasut.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (22 commits)
r8169: fix PHY driver check on platforms w/o module softdeps
net: ks8851-ml: Fix IO operations, again
mlxsw: spectrum_mr: Fix list iteration in error path
qlcnic: Fix bad kzalloc null test
mac80211: set IEEE80211_TX_CTRL_PORT_CTRL_PROTO for nl80211 TX
mac80211: mark station unauthorized before key removal
mac80211: Check port authorization in the ieee80211_tx_dequeue() case
cfg80211: Do not warn on same channel at the end of CSA
mac80211: drop data frames without key on encrypted links
ieee80211: fix HE SPR size calculation
nl80211: fix NL80211_ATTR_CHANNEL_WIDTH attribute type
xfrm: policy: Fix doulbe free in xfrm_policy_timer
bpf: Explicitly memset some bpf info structures declared on the stack
bpf: Explicitly memset the bpf_attr structure
bpf: Sanitize the bpf_struct_ops tcp-cc name
vti6: Fix memory leak of skb if input policy check fails
esp: remove the skb from the chain when it's enqueued in cryptd_wq
ipv6: xfrm6_tunnel.c: Use built-in RCU list checking
xfrm: add the missing verify_sec_ctx_len check in xfrm_add_acquire
xfrm: fix uctx len check in verify_sec_ctx_len
...
