The OMAP powerdomain code and data is all OMAP2+-specific. This seems
unlikely to change any time soon. Move plat-omap/include/plat/powerdomain.h
to mach-omap2/powerdomain.h. The primary point of doing this is to remove
the temptation for unrelated upper-layer code to access powerdomain code
and data directly.
As part of this process, remove the references to powerdomain data
from the GPIO "driver" and the OMAP PM no-op layer, both in plat-omap.
Change the DSPBridge code to point to the new location for the
powerdomain headers. The DSPBridge code should not be including the
powerdomain headers; these should be removed.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Omar Ramirez Luna <omar.ramirez@ti.com>
Cc: Felipe Contreras <felipe.contreras@gmail.com>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Remove unused code:
- macros,
- variables,
- unused semaphore locking API. This API shall be added back
when needed,
- infinite loops for debug.
Tested on N900 and Beagleboard with full RET and OFF modes,
using cpuidle and suspend.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Tested-by: Nishanth Menon<nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Limitation i583: Self_Refresh Exit issue after OFF mode
Issue:
When device is waking up from OFF mode, then SDRC state machine sends
inappropriate sequence violating JEDEC standards.
Impact:
OMAP3630 < ES1.2 is impacted as follows depending on the platform:
CS0: for 38.4MHz as internal sysclk, DDR content seen to be stable, while
for all other sysclk frequencies, varied levels of instability
seen based on varied parameters.
CS1: impacted
This patch takes option #3 as recommended by the Silicon erratum:
Avoid core power domain transitioning to OFF mode. Power consumption
impact is expected in this case.
To do this, we route core OFF requests to RET request on the impacted
revisions of silicon.
Acked-by: Jean Pihet <j-pihet@ti.com>
[nm@ti.com: rebased the code to 2.6.37-rc2- short circuit code changed a bit]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Currently omap3_cpuidle_update_states makes whole sale decision
on which C states to update based on enable_off_mode variable
Instead, achieve the same functionality by independently providing
mpu and core deepest states the system is allowed to achieve and
update the idle states accordingly.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
[khilman: fixed additional user of this API in OMAP CPUidle driver]
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
While coming out of MPU OSWR/OFF states, L2 controller is reseted.
The reset behavior is implementation specific as per ARMv7 TRM and
hence $L2 needs to be invalidated before it's use. Since the
AUXCTRL register is also reconfigured, disable L2 cache before
invalidating it and re-enables it afterwards. This is as per
Cortex-A8 ARM documentation.
Currently this is identified as being needed on OMAP3630 as the
disable/enable is done from "public side" while, on OMAP3430, this
is done in the "secure side".
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[nm@ti.com: ported to 2.6.37-rc2, added hooks to enable the logic only on 3630]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Peter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Erratum id: i608
RTA (Retention Till Access) feature is not supported and leads to device
stability issues when enabled. This impacts modules with embedded memories
on OMAP3630
Workaround is to disable RTA on boot and coming out of core off.
For disabling RTA coming out of off mode, we do this by overriding the
restore pointer for 3630 as the first point of entry before caches are
touched and is common for GP and HS devices. To disable earlier than
this could be possible by modifying the PPA for HS devices, but not for
GP devices.
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[ambresh@ti.com: co-developer]
Signed-off-by: Ambresh K <ambresh@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Introduce errata handling for OMAP3. This patch introduces
errata variable and stub for initialization which will be
filled up by follow-on patches.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add OPP data for OMAP34xx and OMAP36xx and initialization functions
to populate OPP tables based on current SoC.
introduce an OMAP generic opp initialization routine which OMAP3
and OMAP4+ SoCs can use to register their OPP definitions.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Since 6cdee91257 the references to
enable_off_mode and sleep_while_idle can't be resolved when CONFIG_PM_DEBUG
isn't set:
arch/arm/mach-omap2/built-in.o: In function `omap_uart_restore_context':
arch/arm/mach-omap2/serial.c:253: undefined reference to `enable_off_mode'
arch/arm/mach-omap2/built-in.o: In function `omap3_can_sleep':
arch/arm/mach-omap2/pm34xx.c:479: undefined reference to `sleep_while_idle'
Simply #define these in pm.h just like omap2_pm_debug.
Signed-off-by: Loïc Minier <loic.minier@linaro.org>
[khilman: moved down into existing #ifdef section]
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The set_pwrdm_state() is needed on omap4 as well so move
this routine to common pm.c file so that it's available for omap3/4
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch moves omap2_pm_wakeup_on_timer() and pm debug entries
form pm34xx.c to pm-debug.c and export it, so that it is available
to other OMAPs
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Millisecond resolution is possible and there are use cases for it
(automatic testing).
Seconds-based interface is preserved for compatibility.
Signed-off-by: Ari Kauppi <Ext-Ari.Kauppi@nokia.com>
Reviewed-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Different boards benefit differently from the available
seven C-states for cpu idle. In most cases, only few,
properly spaced (in terms of consumption and latency)
C-states are required to make the power management
optimal. Hence we need a possibility to pass which
C-states are actually used for each board.
So added the valid field to cpuidle_params and added
support to 3430sdp, which uses the paramenter passing.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The CPUidle C state latencies and thresholds are dependent on various
board specific details. This patch makes it possible to configure
these values from the respective board files.
omap3_pm_init_cpuidle() can now be optionally called from board files
to pass board specific cpuidle parameters. If the board files do not
use this function to pass the params default values are used which
might cause higher consumption dur to wrong state selection by the
governor.
This patch only updates the 3430sdp board files to use
omap3_pm_init_cpuidle().
From Kalle, in addition to original patch from Rajendra:
Building without CONFIG_CPU_IDLE or CONFIG_PM causes build to fail if
cpu idle parameters are tried to pass using omap3_pm_init_cpuidle
function.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
When 'enable_off_mode' is 0, the target power state for MPU
and CORE was locally changed to PWRDM_POWER_RET but, the
statistics are updated for idle state originally selected
by the governor.
This patch 'invalidates' the idle states that lead either of
MPU or Core to PWRDM_POWER_OFF state when 'enable_off_mode'
is '0'. The states are valid once 'enable_off_mode' is set
to '1'.
Added function next_valid_state() to check if current state
is valid; else get the next valid state. It is called from
omap3_enter_idle_bm().
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The PM debug code fails to build on when CONFIG_DEBUG_FS is not
enabled.
Build error log:
arch/arm/mach-omap2/built-in.o: In function `omap_sram_idle':
arch/arm/mach-omap2/pm34xx.c:449: undefined reference to `pm_dbg_regset_save'
arch/arm/mach-omap2/pm34xx.c:460: undefined reference to `pm_dbg_regset_save'
arch/arm/mach-omap2/built-in.o: In function `configure_vc':
arch/arm/mach-omap2/pm34xx.c:1237: undefined reference to `pm_dbg_regset_init'
arch/arm/mach-omap2/pm34xx.c:1238: undefined reference to `pm_dbg_regset_init'
make: *** [.tmp_vmlinux1] Error 1
This patch fixes the above errors.
Kernel booting is tested on omap zoom2 and zoom3 boards.
Signed-off-by: Manjunatha GK <manjugk@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Previously omap3_idle_init() was called in device_init, while
omap_pm_init() is called at late_initcall. This causes the cpu idle
driver to call omap_sram_idle before it is properly initialized. This
patch fixes the issue by moving omap3_idle_init into omap3_pm_init.
Signed-off-by: Kalle Jokiniemi <ext-kalle.jokiniemi@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds support and enables state C4(MPU RET + CORE RET)
and MPU OFF states (C3 and C5.)
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Basic CPUidle driver for OMAP3 with deepest sleep state supported
being MPU CSWR.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Using debugfs, export a configurable wakeup timer to be used to
wakeup system from suspend.
If a non-zero value is written to
/debug/pm_debug/wakeup_timer_seconds, A timer wakeup event will wake
the system and resume after the configured number of seconds.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Allow enable/disable of low-power states during idle. To
enable low-power idle:
echo 1 > /debug/pm_debug/sleep_while_idle
to disable:
echo 0 > /debug/pm_debug/sleep_while_idle
Also allow enable/disable of OFF-mode. To enable:
echo 1 > /debug/pm_debug/enable_off_mode
to disable:
echo 0 > /debug/pm_debug/enable_off_mode
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
For HS/EMU devices, some additional resources need to be
saved/restored for off-mode support. Namely, saving the secure RAM
and a pointer to it in the scratchpad.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Move the remaining headers under plat-omap/include/mach
to plat-omap/include/plat. Also search and replace the
files using these headers to include using the right path.
This was done with:
#!/bin/bash
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
headers=$(cd $mach_dir_old && ls *.h)
omap_dirs="arch/arm/*omap*/ \
drivers/video/omap \
sound/soc/omap"
other_files="drivers/leds/leds-ams-delta.c \
drivers/mfd/menelaus.c \
drivers/mfd/twl4030-core.c \
drivers/mtd/nand/ams-delta.c"
for header in $headers; do
old="#include <mach\/$header"
new="#include <plat\/$header"
for dir in $omap_dirs; do
find $dir -type f -name \*.[chS] | \
xargs sed -i "s/$old/$new/"
done
find drivers/ -type f -name \*omap*.[chS] | \
xargs sed -i "s/$old/$new/"
for file in $other_files; do
sed -i "s/$old/$new/" $file
done
done
for header in $(ls $mach_dir_old/*.h); do
git mv $header $plat_dir_new/
done
Signed-off-by: Tony Lindgren <tony@atomide.com>
Target state can be read / programmed via files under:
[debugfs]/pm_debug/[pwrdm]/suspend
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Allows dumping out current register contents from the debug filesystem, and
also allows user to add arbitrary register save points into code. Current
register contents are available under debugfs at:
[debugfs]/pm_debug/registers/current
To add a save point, do following:
From module init (or somewhere before the save call, called only once):
pm_dbg_init_regset(n); // n=1..4, allocates memory for dump area #n
From arbitrary code location:
pm_dbg_regset_save(n); // n=1..4, saves registers to dump area #n
After this, the register dump can be seen under [debugfs]/pm_debug/registers/n
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch provides the debugfs entries and a function which will be
called by the PM code to register the time spent per domain per
state. Also some new fields are added to the powerdomain struct to
keep the time information.
NOTE: As of v2.6.29, using getnstimeofday() after drivers are
suspended is no longer safe since the timekeeping subsystem is also
suspended as part of the suspend process. Instead use sched_clock()
which on OMAP returns the 32k SYNC timer in nanoseconds.
Also, do not print out status for meta powerdomains (dpll*)
Signed-off-by: Peter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch is to sync the core linux-omap PM code with mainline. This
code has evolved and been used for a while the linux-omap tree, but
the attempt here is to finally get this into mainline.
Following this will be a series of patches from the 'PM branch' of the
linux-omap tree to add full PM hardware support from the linux-omap
tree.
Much of this PM core code was written by Jouni Hogander with
significant contributions from Paul Walmsley as well as many others
from Nokia, Texas Instruments and linux-omap community.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
