Moved the pic initialization into its own common file and out of the board
code. Also fixed the OF reference counting on the mpic node.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Initialize I2C pins on boards with CPM1/CPM2 controllers and document the
i2c bus in booting-without-of.
The boards don't have any I2C chips connected to the I2C bus, so unless
some external chips are connected to the boards, this code is just an
example of setting everything else up.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for the MPC8536 process and MPC8536DS reference board. The
MPC8536 is an e500v2 based SoC which eTSEC, USB, SATA, PCI, and PCIe.
The USB and SATA IP blocks are similiar to those on the PQ2 Pro SoCs and
thus use the same drivers.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
These issues were reported by Stephen Rothwell for another 85xx board
port and pointed out by Chen Gong as issues in the DS port.
* mpic OF node reference counting was off
* of_device_id struct should be marked as __initdata
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix interrupt threading issue on pq2fads when running with CONFIG_PREEMPT_RT
Signed-off-by: Rune Torgersen <runet@innovsys.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The following patch restores the PERR and SERR bits in the PCI
command register during an EEH device recovery. We have found
at least one case (an Agilent test card) where the PERR/SERR
bits are set to 1 by firmware at boot time, but are not restored
to 1 during EEH recovery. The patch fixes the Agilent card
problem. It has been tested on several other EEH-enabled cards
with no regressions.
Signed-off-by: Mike Mason <mmlnx@us.ibm.com>
Acked-by: Linas Vepstas <linasvepstas@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The current low level hash code on LPAR configurations clears
_PAGE_COHERENT (M) when either _PAGE_GUARDED (G) or _PAGE_NO_CACHE (I)
is set. This conflicts with _PAGE_SAO which has M, I and W bits sets at
once (normally invalid combo) to indicate the new SAO attribute.
This changes the code to allow that case.
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Make cell_dma_dev_setup_iommu() return a pointer to the struct iommu_table
(or NULL if no table can be found) rather than putting this pointer into
dev->archdata.dma_data (let the caller do that), and rename this function
to cell_get_iommu_table() to reflect this change.
This will allow us to get the iommu table for a device that doesn't have
the table in the archdata.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Update powerpc to use the new dma_*map*_attrs() interfaces. In doing so
update struct dma_mapping_ops to accept a struct dma_attrs and propagate
these changes through to all users of the code (generic IOMMU and the
64bit DMA code, and the iseries and ps3 platform code).
The old dma_*map_*() interfaces are reimplemented as calls to the
corresponding new interfaces.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As nr_active counter includes also spus waiting for syscalls to return
we need a seperate counter that only counts spus that are currently running
on spu side. This counter shall be used by a cpufreq governor that targets
a frequency dependent from the number of running spus.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reduce the output verbosity of ps3_system_bus_match().
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, the .ctx debug file in spu context directories is always
present.
We'd prefer to prevent users from relying on this file, so add a
"debug" mount option to spufs. The .ctx file will only be added to
the context directories when this option is present.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Populate the size member of a few context files. Leave out files that
have different semantics with read vs mmap, or contain a
variable-length hex string.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Currently, spufs never specifies the i_size for the files in context
directories, so stat() always reports 0-byte files.
This change adds allows the spufs_dir_(nosched_)contents arrays to
specify a file size. This allows stat() to report correct file sizes,
and makes SEEK_END work.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
An spu context shouldn't get an extra tick if the time slice code
couldn't find something else to run. This means contexts that are not
within spu_run (ie, SPU_SCHED_SPU_RUN is cleared) will not receive
extra ticks while we have no other contexts waiting.
Signed-off-by: Luke Browning <lukebrowning@us.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Add a ctxt file to spufs that shows spu context information that is used
in scheduling. This info can be used for debugging spufs scheduler
issues, and to isolate between application and spufs problems as it
shows a lot of state such as priorities and dispatch counts.
This file contains internal spufs state and is subject to change at any
time, and therefore no applications should depend on it. The file is
intended for the use of spufs kernel developers.
Signed-off-by: Luke Browning <lukebrowning@us.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
This updates the device tree manipulation routines so that memory
add/remove of lmbs represented under the
ibm,dynamic-reconfiguration-memory node of the device tree invokes the
hotplug notifier chain.
This change is needed because of the change in the way memory is
represented under the ibm,dynamic-reconfiguration-memory node. All lmbs
are described in the ibm,dynamic-memory property instead of having a
separate node for each lmb as in previous device tree layouts. This
requires the update_node() routine to check for updates to the
ibm,dynamic-memory property and invoke the hotplug notifier chain.
This also updates the pseries hotplug notifier to be able to gather information
for lmbs represented under the ibm,dynamic-reconfiguration-memory node and
have the lmbs added/removed.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use the base address of the lmb to derive the starting page frame number
instead of trying to extract it from the drc index of the lmb. The drc
index should not be used for this as it will, and did, break.
Until this point, systems that have had memory represented in the device
tree with a node for each lmb the drc index would (luckily) closely
track the base address of the lmb. For example a lmb with a drc index
of 8000000a would have a base address of a0000000. This correlation
allowed the current code to derive the starting page frame number from
the drc inddex
Device tree layouts where lmbs are represented under the
ibm,dynamic-reconfiguration-memory node in the ibm,dynamic-memory
property do not have this correlation between the drc index and base
address of the lmb.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Allow the phandle passed to the /proc/ppc64/ofdt file to be specified
in formats other than decimal. This allows us to easily specify phandle
values in hex that would otherwise appear as negative integers.
This is an issue on systems where the value of
/proc/device-tree/ibm,dynamic-reconfiguration-memory.ibm,phandle is
fffffff9. Having to pass this to the ofdt file as a string results in
a large negative number, and simple_strtoul() does not handle negative
numbers.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Suspend/resume ("echo mem > /sys/power/state") does not work with
vanilla kernels -- the system does not suspend correctly and just
hangs. This patch fixes this so suspend/resume works:
1) of_iomap does not map the whole 0xC000 of the MPC5200 immr so
saving registers does not work.
2) PCI registers need to be saved and restored.
Signed-off-by: Tim Yamin <plasm@roo.me.uk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add CONFIG_VSX config build option. Must compile with POWER4, FPU and ALTIVEC.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently create_branch() creates a branch instruction for you, and
patches it into the call site. In some circumstances it would be nice
to be able to create the instruction and patch it later, and also some
code might want to check for errors in the branch creation before
doing the patching. A future commit will change create_branch() to
check for errors.
For callers that don't care, replace create_branch() with
patch_branch(), which just creates the branch and patches it directly.
While we're touching all the callers, change to using unsigned int *,
as this seems to match usage better. That allows (and requires) us to
remove the volatile in the definition of vector in powermac/smp.c and
mpc86xx_smp.c, that's correct because now that we're passing vector as
an unsigned int * the compiler knows that it's value might change
across the patch_branch() call.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We currently have a few routines for patching code in asm/system.h, because
they didn't fit anywhere else. I'd like to clean them up a little and add
some more, so first move them into a dedicated C file - they don't need to
be inlined.
While we're moving the code, drop create_function_call(), it's intended
caller never got merged and will be replaced in future with something
different.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
At present, if we have a kernel with a 64kB page size, and some
process maps something that has to be mapped with 4kB pages (such as a
cache-inhibited mapping on POWER5+, or the eHCA infiniband queue-pair
pages), we change the process to use 4kB pages everywhere. This hurts
the performance of HPC programs that access eHCA from userspace.
With this patch, the kernel will only demote the slice(s) containing
the eHCA or cache-inhibited mappings, leaving the remaining slices
able to use 64kB hardware pages.
This also changes the slice_get_unmapped_area code so that it is
willing to place a 64k-page mapping into (or across) a 4k-page slice
if there is no better alternative, i.e. if the program specified
MAP_FIXED or if there is not sufficient space available in slices that
are either empty or already have 64k-page mappings in them.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We need to disable ptcal before starting a new kernel after a crash,
in order to avoid overwriting data in the kdump kernel.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The pseries_kexec_setup function overwrites some ppc_md
pointers, so make sure it only gets called when running on
the right architecture.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Ports B and C pins programming is changed to get SCC2 UART and FCC3
ethernet work.
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The new e500mc core from Freescale is based on the e500v2 but with the
following changes:
* Supports only the Enhanced Debug Architecture (DSRR0/1, etc)
* Floating Point
* No SPE
* Supports lwsync
* Doorbell Exceptions
* Hypervisor
* Cache line size is now 64-bytes (e500v1/v2 have a 32-byte cache line)
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix this:
/usr/src/devel/arch/powerpc/platforms/pseries/eeh_driver.c: In function 'print_device_node_tree':
/usr/src/devel/arch/powerpc/platforms/pseries/eeh_driver.c:55: warning: ISO C90 forbids mixed declarations and code
also make that function look like it's part of Linux.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
of_node_put is needed before discarding a value received from
of_find_node_by_type, eg in error handling code.
The semantic patch that makes the change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
struct device_node *n;
struct device_node *n1;
struct device_node *n2;
statement S;
identifier f1,f2;
expression E1,E2;
constant C;
@@
n = of_find_node_by_type(...)
...
if (!n) S
... when != of_node_put(n)
when != n1 = f1(n,...)
when != E1 = n
when any
when strict
(
+ of_node_put(n);
return -C;
|
of_node_put(n);
|
n2 = f2(n,...)
|
E2 = n
|
return ...;
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There is a delay in the transition to the stopped state for class 2
interrupts. In some cases, the controlling thread detects the state of
the spu as running, and goes back to sleep resulting in a hung
application as the event is missed.
This change detects the stop condition and re-generates the wakeup event
after a context save.
Signed-off-by: Luke Browning <lukebrowning@us.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Time slicing can occur at the same time as spu exception handling
resulting in the wakeup of the wrong thread.
This change uses the the spu's register_lock to enforce synchronization
between bind/unbind and spu exception handling so that they are
mutually exclusive.
Signed-off-by: Luke Browning <lukebrowning@us.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
According to the CBEA, the SPU dsisr is not updated for class 0
exceptions.
spu_stopped() is testing the dsisr that was passed to it from the class
0 exception handler, so we return a false positive here.
This patch cleans up the interrupt handler and erroneous tests in
spu_stopped. It also removes the fields from the csa since it is not
needed to process class 0 events.
Signed-off-by: Luke Browning <lukebrowning@us.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
If the spu is stopping (ie, the SPU_STATUS_RUNNING bit is still set),
re-read the register to get the final stopped value.
Signed-off-by: Luke Browning <lukebrowning@us.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
The Sam440ep is an high customizable general purpose mini-itx board,
based on the AMCC 440EP and with a LatticeXP FPGA onboard.
It's poduced by ACube Systems Srl (Bassano del Grappa, Italy),
http://www.acube-systems.biz.
Signed-off-by: Giuseppe Coviello <gicoviello@gmail.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The "ndfc-chip" device doesn't need any resources. All resources
are handled by the "ndfc-nand" device. Registering the same memory
resource twice causes "cat /proc/iomem" to go into an infinite loop
displaying NDFC memory addresses.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This is patch adds board file, device tree, and defconfig for the new
board, made by Freescale Semiconductor Inc. and Logic Product Development.
Currently supported:
1. UEC{1,2,7,4};
2. I2C;
3. SPI;
4. NS16550 serial;
5. PCI and miniPCI;
6. Intel NOR StrataFlash X16 64Mbit PC28F640P30T85;
7. Graphics controller, Fujitsu MB86277.
Not supported in this patch:
1. StMICRO NAND512W3A2BN6E, 512 Mbit (supported with FSL UPM NAND driver);
2. FHCI USB (supported with FHCI driver).
3. QE Serial UCCs (tested to not work with ucc_uart driver, reason
unknown, yet);
4. ADC AD7843 (tested to work, but support via device tree depends on
major SPI rework, GPIO API, etc);
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds support for the TQM8548 modules from TQ-Components
GmbH (http://www.tqc.de).
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Like for the TQM5200, the vendor prefix "tqc," is now used for all
TQM85xx modules from TQ-Components GmbH (http://www.tqc.de) in the
corresponding DTS files.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC85xx MDS board requires some board level tweaks of the PHYs that
either the eTSEC (gianfar) or UCC ethernet controllers are connected to.
Its possible to build the phylib as a module, however this breaks the
board level fix ups because phy_read and phy_write are not available
if we build as a module.
So we unconditionally select PHYLIB to ensure its built into the kernel
if we are building in MPC85xx MDS support. This was determined to be
the easiest soultion even though it prevents the user from removing
PHYLIB support if they decide they don't want it.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When I changed irq_alloc_host() to take an of_node
(52964f87c6: "Add an optional
device_node pointer to the irq_host"), I botched the reference
counting semantics.
Stephen pointed out that it's irq_alloc_host()'s business if
it needs to take an additional reference to the device_node,
the caller shouldn't need to care.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If we do the call to irq_of_parse_and_map() first, then we don't
need to worry about freeing the irq_host.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Support for the C2K cPCI Single Board Computer from GEFanuc
(PowerPC MPC7448 with a Marvell MV64460 chipset).
All features of the board are not supported yet, but the board
boots, flash works, all Ethernet ports are working and PCI
devices are all found (USB and SATA on PCI1 do not work yet).
Part 5 of 5: add the Kconfig entry for the C2K board.
Signed-off-by: Remi Machet <rmachet@slac.stanford.edu>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Support for the C2K cPCI Single Board Computer from GEFanuc
(PowerPC MPC7448 with a Marvell MV64460 chipset).
All features of the board are not supported yet, but the board
boots, flash works, all Ethernet ports are working and PCI
devices are all found (USB and SATA on PCI1 do not work yet).
Part 3 of 5: driver for the board. At this time it is very generic
and similar to its original, the driver for the prpmc2800.
Signed-off-by: Remi Machet <rmachet@slac.stanford.edu>
Signed-off-by: Paul Mackerras <paulus@samba.org>
