Andrew Lunn pointed out that even if it's documented that
ethnl_parse_header() takes reference to network device if it fills it
into the target structure, its name doesn't make it apparent so that
corresponding dev_put() looks like mismatched.
Rename the function ethnl_parse_header_dev_get() to indicate that it
takes a reference.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add relevant getter for ct info dissector.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the zone's flow table instance on the flow action to the drivers.
Thus, allowing drivers to register FT add/del/stats callbacks.
Finally, enable hardware offload on the flow table instance.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If driver deleted an FT entry, a FT failed to offload, or registered to the
flow table after flows were already added, we still get packets in
software.
For those packets, while restoring the ct state from the flow table
entry, refresh it's hardware offload.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide an API to restore the ct state pointer.
This may be used by drivers to restore the ct state if they
miss in tc chain after they already did the hardware connection
tracking action (ct_metadata action).
For example, consider the following rule on chain 0 that is in_hw,
however chain 1 is not_in_hw:
$ tc filter add dev ... chain 0 ... \
flower ... action ct pipe action goto chain 1
Packets of a flow offloaded (via nf flow table offload) by the driver
hit this rule in hardware, will be marked with the ct metadata action
(mark, label, zone) that does the equivalent of the software ct action,
and when the packet jumps to hardware chain 1, there would be a miss.
CT was already processed in hardware. Therefore, the driver's miss
handling should restore the ct state on the skb, using the provided API,
and continue the packet processing in chain 1.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NF flow table API associate 5-tuple rule with an action list by calling
the flow table type action() CB to fill the rule's actions.
In action CB of act_ct, populate the ct offload entry actions with a new
ct_metadata action. Initialize the ct_metadata with the ct mark, label and
zone information. If ct nat was performed, then also append the relevant
packet mangle actions (e.g. ipv4/ipv6/tcp/udp header rewrites).
Drivers that offload the ft entries may match on the 5-tuple and perform
the action list.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let drivers to add their cb allowing them to receive flow offload events
of type TC_SETUP_CLSFLOWER (REPLACE/DEL/STATS) for flows managed by the
flow table.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there is no TCP_LISTEN socket on a ephemeral port, we can bind multiple
sockets having SO_REUSEADDR to the same port. Then if all sockets bound to
the port have also SO_REUSEPORT enabled and have the same EUID, all of them
can be listened. This is not safe.
Let's say, an application has root privilege and binds sockets to an
ephemeral port with both of SO_REUSEADDR and SO_REUSEPORT. When none of
sockets is not listened yet, a malicious user can use sudo, exhaust
ephemeral ports, and bind sockets to the same ephemeral port, so he or she
can call listen and steal the port.
To prevent this issue, we must not bind more than one sockets that have the
same EUID and both of SO_REUSEADDR and SO_REUSEPORT.
On the other hand, if the sockets have different EUIDs, the issue above does
not occur. After sockets with different EUIDs are bound to the same port and
one of them is listened, no more socket can be listened. This is because the
condition below is evaluated true and listen() for the second socket fails.
} else if (!reuseport_ok ||
!reuseport || !sk2->sk_reuseport ||
rcu_access_pointer(sk->sk_reuseport_cb) ||
(sk2->sk_state != TCP_TIME_WAIT &&
!uid_eq(uid, sock_i_uid(sk2)))) {
if (inet_rcv_saddr_equal(sk, sk2, true))
break;
}
Therefore, on the same port, we cannot do listen() for multiple sockets with
different EUIDs and any other listen syscalls fail, so the problem does not
happen. In this case, we can still call connect() for other sockets that
cannot be listened, so we have to succeed to call bind() in order to fully
utilize 4-tuples.
Summarizing the above, we should be able to bind only one socket having
SO_REUSEADDR and SO_REUSEPORT per EUID.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit aacd9289af ("tcp: bind() use stronger
condition for bind_conflict") introduced a restriction to forbid to bind
SO_REUSEADDR enabled sockets to the same (addr, port) tuple in order to
assign ports dispersedly so that we can connect to the same remote host.
The change results in accelerating port depletion so that we fail to bind
sockets to the same local port even if we want to connect to the different
remote hosts.
You can reproduce this issue by following instructions below.
1. # sysctl -w net.ipv4.ip_local_port_range="32768 32768"
2. set SO_REUSEADDR to two sockets.
3. bind two sockets to (localhost, 0) and the latter fails.
Therefore, when ephemeral ports are exhausted, bind(0) should fallback to
the legacy behaviour to enable the SO_REUSEADDR option and make it possible
to connect to different remote (addr, port) tuples.
This patch allows us to bind SO_REUSEADDR enabled sockets to the same
(addr, port) only when net.ipv4.ip_autobind_reuse is set 1 and all
ephemeral ports are exhausted. This also allows connect() and listen() to
share ports in the following way and may break some applications. So the
ip_autobind_reuse is 0 by default and disables the feature.
1. setsockopt(sk1, SO_REUSEADDR)
2. setsockopt(sk2, SO_REUSEADDR)
3. bind(sk1, saddr, 0)
4. bind(sk2, saddr, 0)
5. connect(sk1, daddr)
6. listen(sk2)
If it is set 1, we can fully utilize the 4-tuples, but we should use
IP_BIND_ADDRESS_NO_PORT for bind()+connect() as possible.
The notable thing is that if all sockets bound to the same port have
both SO_REUSEADDR and SO_REUSEPORT enabled, we can bind sockets to an
ephemeral port and also do listen().
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we get an ephemeral port, the relax is false, so the SO_REUSEADDR
conditions may be evaluated twice. We do not need to check the conditions
again.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparse reports a warning at netlink_seq_start()
warning: context imbalance in netlink_seq_start() - wrong count at exit
The root cause is the missing annotation at netlink_seq_start()
Add the missing __acquires(RCU) annotation
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparse reports warning at tcp_child_process()
warning: context imbalance in tcp_child_process() - unexpected unlock
The root cause is the missing annotation at tcp_child_process()
Add the missing __releases(&((child)->sk_lock.slock)) annotation
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparse reports warnings at raw_seq_start() and raw_seq_stop()
warning: context imbalance in raw_seq_start() - wrong count at exit
warning: context imbalance in raw_seq_stop() - unexpected unlock
The root cause is the missing annotations at raw_seq_start()
and raw_seq_stop()
Add the missing __acquires(&h->lock) annotation
Add the missing __releases(&h->lock) annotation
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In their .attach callback, mq[prio] only add the qdiscs of the currently
active TX queues to the device's qdisc hash list.
If a user later increases the number of active TX queues, their qdiscs
are not visible via eg. 'tc qdisc show'.
Add a hook to netif_set_real_num_tx_queues() that walks all active
TX queues and adds those which are missing to the hash list.
CC: Eric Dumazet <edumazet@google.com>
CC: Jamal Hadi Salim <jhs@mojatatu.com>
CC: Cong Wang <xiyou.wangcong@gmail.com>
CC: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When pktgen is used to measure the performance of dev_queue_xmit()
packet handling in the core, it is preferable to not hand down
packets to a low-level Ethernet driver as it would distort the
measurements.
Allow using pktgen on the loopback device, thus constraining
measurements to core code.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mptcp rcvbuf size is adjusted according to the subflow rcvbuf size.
This should not be done if userspace did set a fixed value.
Fixes: 600911ff5f ("mptcp: add rmem queue accounting")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
- bump version strings, by Simon Wunderlich
- Avoid RCU list-traversal in spinlock, by Sven Eckelmann
- Replace zero-length array with flexible-array member,
by Gustavo A. R. Silva
-----BEGIN PGP SIGNATURE-----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=f2xH
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-for-davem-20200306' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This cleanup patchset includes the following patches:
- bump version strings, by Simon Wunderlich
- Avoid RCU list-traversal in spinlock, by Sven Eckelmann
- Replace zero-length array with flexible-array member,
by Gustavo A. R. Silva
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 105e808c1d ("pie: remove pie_vars->accu_prob_overflows")
changes the scale of probability values in PIE from (2^64 - 1) to
(2^56 - 1). This affects the precision of tc_pie_xstats->prob in
user space.
This patch ensures user space is unaffected.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TCP_NLA_BYTES_NOTSENT to SCM_TIMESTAMPING_OPT_STATS that reports
bytes in the write queue but not sent. This is the same metric as
what is exported with tcp_info.tcpi_notsent_bytes.
Signed-off-by: Yousuk Seung <ysseung@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, user who is adding an action expects HW to report stats,
however it does not have exact expectations about the stats types.
That is aligned with TCA_ACT_HW_STATS_TYPE_ANY.
Allow user to specify the type of HW stats for an action and require it.
Pass the information down to flow_offload layer.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce flow_action_basic_hw_stats_types_check() helper and use it
in drivers. That sanitizes the drivers which do not have support
for action HW stats types.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Invoke ndo_setup_tc() as appropriate to signal init / replacement,
destroying and dumping of pFIFO / bFIFO Qdisc.
A lot of the FIFO logic is used for pFIFO_head_drop as well, but that's a
semantically very different Qdisc that isn't really in the same boat as
pFIFO / bFIFO. Split some of the functions to keep the Qdisc intact.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linux supports 22 different interrupt coalescing parameters.
No driver implements them all. Some drivers just ignore the
ones they don't support, while others have to carry a long
list of checks to reject unsupported settings.
To simplify the drivers add the ability to specify inside
ethtool_ops which parameters are supported and let the core
reject attempts to set any other one.
This commit makes the mechanism an opt-in, only drivers which
set ethtool_opts->coalesce_types to a non-zero value will have
the checks enforced.
The same mask is used for global and per queue settings.
v3: - move the (temporary) check if driver defines types
earlier (Michal)
- rename used_types -> nonzero_params, and
coalesce_types -> supported_coalesce_params (Alex)
- use EOPNOTSUPP instead of EINVAL (Andrew, Michal)
Leaving the long series of ifs for now, it seems nice to
be able to grep for the field and flag names. This will
probably have to be revisited once netlink support lands.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the commit e0a4b99773 ("hsr: use upper/lower device infrastructure"),
dev_get() was removed but dev_put() in the error path wasn't removed.
So, if creating hsr interface command is failed, the reference counter leak
of lower interface would occur.
Test commands:
ip link add dummy0 type dummy
ip link add ipvlan0 link dummy0 type ipvlan mode l2
ip link add ipvlan1 link dummy0 type ipvlan mode l2
ip link add hsr0 type hsr slave1 ipvlan0 slave2 ipvlan1
ip link del ipvlan0
Result:
[ 633.271992][ T1280] unregister_netdevice: waiting for ipvlan0 to become free. Usage count = -1
Fixes: e0a4b99773 ("hsr: use upper/lower device infrastructure")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ocelot has the concept of a CPU port. The CPU port is represented in the
forwarding and the queueing system, but it is not a physical device. The
CPU port can either be accessed via register-based injection/extraction
(which is the case of Ocelot), via Frame-DMA (similar to the first one),
or "connected" to a physical Ethernet port (called NPI in the datasheet)
which is the case of the Felix DSA switch.
In Ocelot the CPU port is at index 11.
In Felix the CPU port is at index 6.
The CPU bit is treated special in the forwarding, as it is never cleared
from the forwarding port mask (once added to it). Other than that, it is
treated the same as a normal front port.
Both Felix and Ocelot should use the CPU port in the same way. This
means that Felix should not use the NPI port directly when forwarding to
the CPU, but instead use the CPU port.
This patch is fixing this such that Felix will use port 6 as its CPU
port, and just use the NPI port to carry the traffic.
Therefore, eliminate the "ocelot->cpu" variable which was holding the
index of the NPI port for Felix, and the index of the CPU port module
for Ocelot, so the variable was actually configuring different things
for different drivers and causing at least part of the confusion.
Also remove the "ocelot->num_cpu_ports" variable, which is the result of
another confusion. The 2 CPU ports mentioned in the datasheet are
because there are two frame extraction channels (register based or DMA
based). This is of no relevance to the driver at the moment, and
invisible to the analyzer module.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Suggested-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable pie_vars->accu_prob is used as an accumulator for
probability values. Since probabilty values are scaled using the
MAX_PROB macro denoting (2^64 - 1), pie_vars->accu_prob is
likely to overflow as it is of type u64.
The variable pie_vars->accu_prob_overflows counts the number of
times the variable pie_vars->accu_prob overflows.
The MAX_PROB macro needs to be equal to at least (2^39 - 1) in
order to do precise calculations without any underflow. Thus
MAX_PROB can be reduced to (2^56 - 1) without affecting the
precision in calculations drastically. Doing so will eliminate
the need for the variable pie_vars->accu_prob_overflows as the
variable pie_vars->accu_prob will never overflow.
Removing the variable pie_vars->accu_prob_overflows also reduces
the size of the structure pie_vars to exactly 64 bytes.
Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: Gautam Ramakrishnan <gautamramk@gmail.com>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function pie_calculate_probability(), the variables alpha and
beta are of type u64. The variables qdelay, qdelay_old and
params->target are of type psched_time_t (which is also u64).
The explicit type casting done when calculating the value for
the variable delta is redundant and not required.
Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: Gautam Ramakrishnan <gautamramk@gmail.com>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove ambiguity by using the term backlog instead of qlen when
representing the queue length in bytes.
Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: Gautam Ramakrishnan <gautamramk@gmail.com>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make the filler functions more generic, use network
relative skb pulling.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When checking the protocol number tcf_ct_flow_table_lookup() handles
the flow as if it's always ipv4, while it can be ipv6.
Instead, refactor the code to fetch the tcp header, if available,
in the relevant family (ipv4/ipv6) filler function, and do the
check on the returned tcp header.
Fixes: 46475bb20f ("net/sched: act_ct: Software offload of established flows")
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the immense variety of classification keys and actions available
for tc-flower, as well as due to potentially very different DSA switch
capabilities, it doesn't make a lot of sense for the DSA mid layer to
even attempt to interpret these. So just pass them on to the underlying
switch driver.
DSA implements just the standard boilerplate for binding and unbinding
flow blocks to ports, since nobody wants to deal with that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 2 second delay before calling qrtr_ns_init() meant that the remote
processors would register as endpoints in qrtr and the say_hello() call
would therefor broadcast the outgoing HELLO to them. With the HELLO
handshake corrected this delay is no longer needed.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lost in the translation from the user space implementation was the
detail that HELLO mesages must be exchanged between each node pair. As
such the incoming HELLO must be replied to.
Similar to the previous implementation no effort is made to prevent two
Linux boxes from continuously sending HELLO messages back and forth,
this is left to a follow up patch.
say_hello() is moved, to facilitate the new call site.
Fixes: 0c2204a4ad ("net: qrtr: Migrate nameservice to kernel from userspace")
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a DATA_FIN is sent in a MPTCP DSS option that contains a data
mapping, the DATA_FIN consumes one byte of space in the mapping. In this
case, the DATA_FIN should only be included in the DSS option if its
sequence number aligns with the end of the mapped data. Otherwise the
subflow can send an incorrect implicit sequence number for the DATA_FIN,
and the DATA_ACK for that sequence number would not close the
MPTCP-level connection correctly.
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of reading the MPTCP-level sequence number when sending DATA_FIN,
store the data in the subflow so it can be safely accessed when the
subflow TCP headers are written to the packet without the MPTCP-level
lock held. This also allows the MPTCP-level socket to close individual
subflows without closing the MPTCP connection.
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MPTCP should wait for an active connection or skip sending depending on
the connection state, as TCP does. This happens before the possible
passthrough to a regular TCP sendmsg because the subflow's socket type
(MPTCP or TCP fallback) is not known until the connection is
complete. This is also relevent at disconnect time, where data should
not be sent in certain MPTCP-level connection states.
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently mlx5 PCI PF and VF devlink devices register their ports as
physical port in non-representors mode.
Introduce a new port flavour as virtual so that virtual devices can
register 'virtual' flavour to make it more clear to users.
An example of one PCI PF and 2 PCI virtual functions, each having
one devlink port.
$ devlink port show
pci/0000:06:00.0/1: type eth netdev ens2f0 flavour physical port 0
pci/0000:06:00.2/1: type eth netdev ens2f2 flavour virtual port 0
pci/0000:06:00.3/1: type eth netdev ens2f3 flavour virtual port 0
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Offload nf conntrack processing by looking up the 5-tuple in the
zone's flow table.
The nf conntrack module will process the packets until a connection is
in established state. Once in established state, the ct state pointer
(nf_conn) will be restored on the skb from a successful ft lookup.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a ft entry when connections enter an established state and delete
the connections when they leave the established state.
The flow table assumes ownership of the connection. In the following
patch act_ct will lookup the ct state from the FT. In future patches,
drivers will register for callbacks for ft add/del events and will be
able to use the information to offload the connections.
Note that connection aging is managed by the FT.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the NF flow tables infrastructure for CT offload.
Create a nf flow table per zone.
Next patches will add FT entries to this table, and do
the software offload.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The data pointers of ipv6 sysctl are set one by one which is hard to
maintain, especially with kconfig. This patch simplifies it by using
math to point the per net sysctls into the appropriate struct net,
just like what we did for ipv4.
Signed-off-by: Cambda Zhu <cambda@linux.alibaba.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three virtual devices (ibmveth, virtio_net, and netvsc) all have
similar code to set link settings and validate ethtool command. To
eliminate duplication of code, it is factored out into core/ethtool.c.
Signed-off-by: Cris Forno <cforno12@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev_upper_dev_link() is useful to manage lower/upper interfaces.
And this function internally validates looping, maximum depth.
All or most virtual interfaces that could have a real interface
(e.g. macsec, macvlan, ipvlan etc.) use lower/upper infrastructure.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to access the port list, the hsr_port_get_hsr() is used.
And this is protected by RTNL and RCU.
The hsr_fill_info(), hsr_check_carrier(), hsr_dev_open() and
hsr_get_max_mtu() are protected by RTNL.
So, rcu_read_lock() in these functions are not necessary.
The hsr_handle_frame() also uses rcu_read_lock() but this function
is called by packet path.
It's already protected by RCU.
So, the rcu_read_lock() in hsr_handle_frame() can be removed.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When HSR interface is sending a frame, it finds a node with
the destination ethernet address from the list.
If there is no node, it calls WARN_ONCE().
But, using WARN_ONCE() for this situation is a little bit overdoing.
So, in this patch, the netdev_err() is used instead.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If HSR uses the extack instead of netdev_info(), users can get
error messages immediately without any checking the kernel message.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
