Now that sdhci_set_bus_width() supports 8-bit bus widths based on the
MMC_CAP_8_BIT_DATA capability flag, replace the tegra version with the
generic sdhci version.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Hosts supporting 8-bit bus are marked accordingly. If MMC_CAP_8_BIT_DATA
is not among host capabilities, 8BITBUS bit will never be set and it
is not cleared in case some non-SDHCI3 host uses it for something else.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CQE needs to be off for the host controller to accept non-CQ commands. Turn
off the CQE before sending commands, and ensure it is off in any reset or
power management paths, or re-tuning.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Xenon sdh controller requests proper SD bus voltage select
bits programmed even with vmmc power supply. Any reserved
value(100b-000b) programmed in this field will lead to controller
ignore SD bus power bit and keep its value at zero.
Add set_power callback to handle this.
Signed-off-by: Zhoujie Wu <zjwu@marvell.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Fixes: 3a3748dba8 ("mmc: sdhci-xenon: Add Marvell Xenon SDHC core functionality")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_return_hold() / mmc_retune_release() are used around a group of
commands to prevent re-tuning between the commands. Re-tuning can still
happen before the first command. In some cases, re-tuning must be
prevented entirely. Add mmc_retune_hold_now() for that purpose. It is
added in preparation for CQE support where it will be used by CQE recovery.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Packed commands support was removed but some bits got left behind. Remove
them.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sunxi_mmc_clk_set_phase expects the actual card clock rate to be passed
to it. When the internal divider code was reworked in change ("mmc: sunxi:
Support MMC DDR52 transfer mode with new timing mode"), this requirement
was missed, and the module clock rate was passed in instead. This broke 8
bit DDR MMC on old controllers, as the module clock rate is double the
card clock rate, for which we have no valid delay settings.
Fix this by applying the internal divider to the clock rate right after
we configure it in hardware.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make use of the 64 bit sdbuf width on Renesas R-Car Gen3. If the
registers are 8 byte apart, the width is also 64 bit. For all others,
the width is 32 bit, even if the registers are only 16 bit apart.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We don't use this new define yet, but it is helpful to document which
versions we know of.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Chris Brandt <Chris.Brandt@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is documented, so enable it to follow the recommendation in the docs
and also save a few cycles.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Chris Brandt <Chris.Brandt@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is one SDHI instance on Gen2 which does not have the CBSY bit.
So, turn CBSY usage into an extra flag and set it accordingly. This has
the additional advantage that we can also set it for other incarnations
later.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Chris Brandt <Chris.Brandt@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add Xenon specific system-level suspend and resume support.
Especially during resume, re-configure Xenon specific registers
since registers setting will be lost in suspend if Xenon is power off.
Signed-off-by: Hu Ziji <huziji@marvell.com>
Signed-off-by: Zhoujie Wu <zjwu@marvell.com>
Tested-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Per the databook of designware mmc controller 2.70a, table 3-2, cmd
done interrupt should be fired as soon as the the cmd is sent via
cmd line. And the response timeout interrupt should be generated
unconditioinally as well if the controller doesn't receive the resp.
However that doesn't seem to meet the fact of rockchip specified Soc
platforms using dwmmc. We have continuously found the the cmd done or
response timeout interrupt missed somehow which took us a long time to
understand what was happening. Finally we narrow down the root to
the reconstruction of sample circuit for dwmmc IP introduced by
rockchip and the buggy design sweeps over all the existing rockchip
Socs using dwmmc disastrously.
It seems no way to work around this bug without the proper break-out
mechanism so that we seek for a parallel pair the same as the handling
for missing data response timeout, namely dto timer. Adding this cto
timer seems easily to handle this bug but it's hard to restrict the code
under the rockchip specified context. So after merging this patch, it
sets up the cto timer for all the platforms using dwmmc IP which isn't
ideal but at least we don't advertise new quirk here. Fortunately, no
obvious performance regression was found by test and the pre-existing
similar catch-all timer for sdhci has proved it's an acceptant way to
make the code as robust as possible.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=196321
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
[shawn.lin: rewrite the code and the commit msg throughout]
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This commit modifies dw_mci_probe(), it moves reset assertion before
drv_data->init(host)
Some driver needs to access controller registers in its .init() ops. So,
in order to make such access safe, we should do controller reset before
.init() being called.
Signed-off-by: Wei Li <liwei213@huawei.com>
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Chen Jun <chenjun14@huawei.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Programming legacy HOST SDMA Buffer Boundary bits in Block Size Register
(0x04) is not supported in Qualcomm sdhci controllers. Writing to this
would cause the controller not to transfer last block in case block size
is 4 bytes or less.
This issue was noticed while testing sdio wlan card on Qcom DB410c board.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds sdma_boundary member to struct sdhci_host to give more
flexibility to drivers to control the sdma boundary buffer value and
also to fix issue on some sdhci controllers which are broken when
HOST SDMA Buffer Boundary is programmed in Block Size Register (0x04)
when using ADMA. Qualcomm sdhci controller is one of such type, writing
to this bits is un-supported.
Default value of sdma_boundary is set to SDHCI_DEFAULT_BOUNDARY_ARG.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The structure renesas_sdhi_internal_dmac_dma_ops is only passed as
the second argument to renesas_sdhi_probe, which is const, so
renesas_sdhi_internal_dmac_dma_ops can be const too.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci_pltfm_data structure is only passed as the second argument
of sdhci_pltfm_init, which is const, so the sdhci_pltfm_data structure
can be const as well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci_pltfm_data structure is only passed as the second argument
of sdhci_pltfm_init, which is const, while the sdhci_ops structure
is only stored in the ops field of a sdhci_pltfm_data structure,
which is also const. Thus both kinds of structures can be const as
well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci_pltfm_data structure is only passed as the second argument
of sdhci_pltfm_init, which is const, while the sdhci_ops structure
is only stored in the ops field of a sdhci_pltfm_data structure,
which is also const. Thus both kinds of structures can be const as
well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci_pltfm_data structure is only passed as the second argument
of sdhci_pltfm_init, which is const, while the sdhci_ops structure
is only stored in the ops field of a sdhci_pltfm_data structure,
which is also const. Thus both kinds of structures can be const as
well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci_pltfm_data structure is only passed as the second argument
of sdhci_pltfm_init, which is const, so the sdhci_pltfm_data structure can
be const as well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Per the SD physical layer simplified specification V4.10,
section 4.6.2, CSD version 1.0 SD card should use taac, nsac
and r2w_factor for calculating the data access time. But the
taac and nsac for SDHC(CSD version 2.0) are always fixed and
the software should use the recommended value for timeout. When
parsing the CSD, we sanely set them to zero for SDHC(CSD version
2.0), all the calculation for timeout_ns and timeout_clk is zero
as well. So what we actually want to limit here is either SDHC
case or unreasonable timeout reported by the cards. In principle
we should at least be able to remove the bogus check for the
mmc_card_blockaddr.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
One issue was found on a removable high speed sd card with
runtime pm enabled.
When SD card is unplugged, it keep printing "Switching to 3.3V
signalling voltage failed".
And found below sequence triggers the error.
mmc_rescan
-> mmc_sd_detect
-> mmc_power_off -- mmc->ios.vdd is updated to 0.
-> mmc_claim_host
-> sdhci_runtime_resume_host
-> sdhci_start_signal_voltage_switch
-> mmc_regulator_set_vqmmc
-> mmc_ocrbitnum_to_vdd
When mmc_ocrbitnum_to_vdd is called, the mmc->ios.vdd is 0, so it
always return -EINVAL. The signal switch will always fail and
print out warning.
Ignore restoring the I/O state when runtime resume if MMC_POWER_OFF.
Signed-off-by: Zhoujie Wu <zjwu@marvell.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The A83T MMC support code introduces the timings mode switch, however
such a switch doesn't exist on new SoCs with only new timings mode.
Only execute the switch if the SoC really have the timings mode switch,
to fix the regression shown on new timings mode only SoCs (A64, H5,
etc).
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some SoCs do not support clk delays for MMC in the clock control unit.
These include the old controllers in A10/A10s/A13/R8, and the new eMMC
controller in A64. The config structure for these controllers do not
specify clk_delays, but the check for this was replaced in change
"mmc: sunxi: Support controllers that can use both old and new timings".
This patch adds back the check for clk_delays, and also adds comments
for both checks in sunxi_mmc_clk_set_phase().
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The third MMC controller (MMC2) on the Allwinner A83T SoC is slightly
different. It supports a wider 8-bit bus, has a dedicated controllable
reset pin for eMMC, and a "new timing mode" which is supposed to deliver
better signals and thus better performance.
Add a compatible for this one to use the new timing mode not found in the
other controllers.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC controller can support DDR52 transfers under the new timing
mode. According to the BSP kernel, the module clock has to be double
the card clock, regardless of the bus width. The default timings in
the hardware can be used.
This also reworks the code setting the internal divider, getting rid
of a extra conditional.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On the SoCs that introduced the new timing mode for MMC controllers,
both the old (where the clock delays are set in the CCU) and new
(where the clock delays are set in the MMC controller) timing modes
are available, and we have to support them both. However there are
two bits that control which mode is active. One is in the CCU, the
other is in the MMC controller. The settings on both sides must be
the same, or nothing will work.
The sunxi-ng clock driver provides an API to query and set the
active timing mode. At probe time, we try to set the active mode
to the "new timing mode". If it succeeds, we can then use the MMC
controller in the new mode. If not, we fall back to the old mode.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Provide a whitelist for Gen3 SoC ES versions for both the SYS DMAC and
internal DMAC variants of the SDHI driver. This is to allow drivers to
only initialise for Gen3 SoC ES versions for which they are the appropriate
DMAC implementation. Currently internal DMAC is the appropriate
implementation for all supported Gen3 SoC ES versions.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Per the spec of JESD84-B51, section 7.3, replace tacc with taac to
fix the obvious typo.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_host_ops structure is only stored in the ops field of an
mmc_host structure, which is declared as const. Thus the mmc_host_ops
structure itself can be const.
Done with the help of Coccinelle.
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct mmc_host_ops i@p = { ... };
@ok1@
struct mmc_host *mmc;
identifier r.i;
position p;
@@
mmc->ops = &i@p
@bad@
position p != {r.p,ok1.p};
identifier r.i;
struct mmc_host_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct mmc_host_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_host_ops structure is only stored in the ops field of an
mmc_host structure, which is declared as const. Thus the mmc_host_ops
structure itself can be const.
Done with the help of Coccinelle.
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct mmc_host_ops i@p = { ... };
@ok1@
struct mmc_host *mmc;
identifier r.i;
position p;
@@
mmc->ops = &i@p
@bad@
position p != {r.p,ok1.p};
identifier r.i;
struct mmc_host_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct mmc_host_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_host_ops structure is only stored in the ops field of an
mmc_host structure, which is declared as const. Thus the mmc_host_ops
structure itself can be const.
Done with the help of Coccinelle.
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct mmc_host_ops i@p = { ... };
@ok1@
struct mmc_host *mmc;
identifier r.i;
position p;
@@
mmc->ops = &i@p
@bad@
position p != {r.p,ok1.p};
identifier r.i;
struct mmc_host_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct mmc_host_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_host_ops structure is only stored in the ops field of an
mmc_host structure, which is declared as const. Thus the mmc_host_ops
structure itself can be const.
Done with the help of Coccinelle.
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct mmc_host_ops i@p = { ... };
@ok1@
struct mmc_host *mmc;
identifier r.i;
position p;
@@
mmc->ops = &i@p
@bad@
position p != {r.p,ok1.p};
identifier r.i;
struct mmc_host_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct mmc_host_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_host_ops structure is only stored in the ops field of an
mmc_host structure, which is declared as const. Thus the mmc_host_ops
structure itself can be const.
Done with the help of Coccinelle.
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct mmc_host_ops i@p = { ... };
@ok1@
struct mmc_host *mmc;
identifier r.i;
position p;
@@
mmc->ops = &i@p
@bad@
position p != {r.p,ok1.p};
identifier r.i;
struct mmc_host_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct mmc_host_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_host_ops structure is only stored in the ops field of an
mmc_host structure, which is declared as const. Thus the mmc_host_ops
structure itself can be const.
Done with the help of Coccinelle.
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct mmc_host_ops i@p = { ... };
@ok1@
struct mmc_host *mmc;
identifier r.i;
position p;
@@
mmc->ops = &i@p
@bad@
position p != {r.p,ok1.p};
identifier r.i;
struct mmc_host_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct mmc_host_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_host_ops structure is only stored in the ops field of an
mmc_host structure, which is declared as const. Thus the mmc_host_ops
structure itself can be const.
Done with the help of Coccinelle.
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct mmc_host_ops i@p = { ... };
@ok1@
struct mmc_host *mmc;
identifier r.i;
position p;
@@
mmc->ops = &i@p
@bad@
position p != {r.p,ok1.p};
identifier r.i;
struct mmc_host_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct mmc_host_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_host_ops structure is only stored in the ops field of an
mmc_host structure, which is declared as const. Thus the mmc_host_ops
structure itself can be const.
Done with the help of Coccinelle.
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct mmc_host_ops i@p = { ... };
@ok1@
struct mmc_host *mmc;
identifier r.i;
position p;
@@
mmc->ops = &i@p
@bad@
position p != {r.p,ok1.p};
identifier r.i;
struct mmc_host_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct mmc_host_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_host_ops structure is only stored in the ops field of an
mmc_host structure, which is declared as const. Thus the mmc_host_ops
structure itself can be const.
Done with the help of Coccinelle.
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct mmc_host_ops i@p = { ... };
@ok1@
struct mmc_host *mmc;
identifier r.i;
position p;
@@
mmc->ops = &i@p
@bad@
position p != {r.p,ok1.p};
identifier r.i;
struct mmc_host_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct mmc_host_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_host_ops structure is only stored in the ops field of an
mmc_host structure, which is declared as const. Thus the mmc_host_ops
structure itself can be const.
Done with the help of Coccinelle.
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct mmc_host_ops i@p = { ... };
@ok1@
struct mmc_host *mmc;
identifier r.i;
position p;
@@
mmc->ops = &i@p
@bad@
position p != {r.p,ok1.p};
identifier r.i;
struct mmc_host_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct mmc_host_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_host_ops structure is only stored in the ops field of an
mmc_host structure, which is declared as const. Thus the mmc_host_ops
structure itself can be const.
Done with the help of Coccinelle.
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct mmc_host_ops i@p = { ... };
@ok1@
struct mmc_host *mmc;
identifier r.i;
position p;
@@
mmc->ops = &i@p
@bad@
position p != {r.p,ok1.p};
identifier r.i;
struct mmc_host_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct mmc_host_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_host_ops structure is only stored in the ops field of an
mmc_host structure, which is declared as const. Thus the mmc_host_ops
structure itself can be const.
Done with the help of Coccinelle.
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct mmc_host_ops i@p = { ... };
@ok1@
struct mmc_host *mmc;
identifier r.i;
position p;
@@
mmc->ops = &i@p
@bad@
position p != {r.p,ok1.p};
identifier r.i;
struct mmc_host_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct mmc_host_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix up a power state in case PCI device has an ACPI companion.
Do it only for Intel Merrifield for now.
This is almost copy'n'paste of part of sdhci_acpi_probe() and might be
split out to a helper function in the future.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
ACPI_COMPANION() macro reduces a code to get a companion device out of
struct device.
Use it instead of an old method.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-mmc@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Jan Glauber <jglauber@cavium.com>
Cc: David Daney <david.daney@cavium.com>
Cc: "Steven J. Hill" <Steven.Hill@cavium.com>
Cc: linux-mmc@vger.kernel.org
Acked-by: David Daney <david.daney@cavium.com>
Tested-by: Steven J. Hill <Steven.Hill@cavium.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I cannot see why this is needed. kmap() should be safe in this case.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
6952 880 0 7832 1e98 drivers/mmc/host/via-sdmmc.o
File size After adding 'const':
text data bss dec hex filename
7032 800 0 7832 1e98 drivers/mmc/host/via-sdmmc.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci uses CONFIG_MMC_DEBUG for showing ADMA descriptor
when occurring ADMA error. And it's also used to dump the
registers whenever calling sdhci_add_host.
On one hand, I don't see any burden to always print the state
ADMA descriptor as it's rare and will help folks better understand
what was happening when seeing ADMA error.
On the other, folks may be interested in checking some registers
at probe time. So we remove the sdhci_dumpregs from __sdhci_add_host
and print some really useful registers in sdhci_setup_host.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
wbsd only use this to print some unsupported command.
However the pr_warn should be enough for dynamic log
control and CONFIG_MMC_DEBUG seems bogus here. Remove it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We have removed all code depending on CONFIG_MMC_DEBUG
from mmc core now. So it's safe to make CONFIG_MMC_DEBUG
just for host drivers only and we expect to kill this option
in the future.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are lots of debug message in core.c which use pr_debug
for better dynamic log level control. So it doesn't make sense
for those print to still keep working only under CONFIG_MMC_DEBUG.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All the check within mmc_mrq_prep seems to be all-or-none
proposition, so it doesn't make sense to only check the
length of sglist only under the CONFIG_MMC_DEBUG context.
I'd prefer to always keep the check there unconditionally.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The intention of this check was to prevent the conflict between
hotplug and removing driver for whatever reason. Currently it
doesn't improve anything and the following rescan process could
still saftly perform the scan flow. So these code seems pointless
now and let's remove them.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It was never used and introduce a warning
drivers/mmc/host/sdhci-acpi.c: In function 'sdhci_acpi_sdio_probe_slot':
drivers/mmc/host/sdhci-acpi.c:297:21: warning: variable 'host' set but
not used [-Wunused-but-set-variable]
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This increases consistency of the code across the sdhci family.
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
for_each_child_of_node performs an of_node_get on each iteration, so a
break out the loop requires an of_node_put.
The semantic patch that fixes this problem is as follows
(http://coccinelle.lip6.fr):
// <smpl>
@@
local idexpression n;
expression e,e1;
iterator name for_each_child_of_node;
@@
for_each_child_of_node(e1,n) {
...
(
of_node_put(n);
|
e = n
|
+ of_node_put(n);
? break;
)
...
}
... when != n
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This adds deepest (Backup+Self-Refresh) PM support to the ATMEL SAMA5D2
SoC's SDHCI controller.
When resuming from deepest state, it is required to restore preset
registers as the registers are lost since VDD core has been shut down
when entering deepest state on the SAMA5D2. The clocks need to be
reconfigured as well.
The other registers and init process are taken care of by the SDHCI
core.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The setting of clocks and presets is currently done in probe only but
once deep PM support is added, it'll be needed in the resume function.
Let's create a function for this setting.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We got a warning:
drivers/mmc/host/atmel-mci.c:1086:15: warning: variable 'sg_len' set but
not used [-Wunused-but-set-variable]
Ideally we should check to see if sg_len is zero but looking
into the code closely, I didn't find any possible to do that as
atmci_start_request didn't even deploy any error handling for
its host->prepare_data hook. So even we return error value for iflags
like what other host drivers did, for instance, sdhci and dwmmc, it still
need some extra work to improve the code.
Just remove it to silent the warning, although it isn't perfect.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It was never used and leave a long standing compile warning:
drivers/mmc/host/sdhci-xenon.c: In function 'xenon_probe':
drivers/mmc/host/sdhci-xenon.c:447:21: warning: variable 'priv' set but
not used [-Wunused-but-set-variable]
Remove it to fix the warning.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It was never used and introduced a long standing compile
warning:
drivers/mmc/core/block.c: In function 'power_ro_lock_store':
drivers/mmc/core/block.c:191:19: warning: variable 'card' set but not
used [-Wunused-but-set-variable]
Remove it to fix the warning.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We got a compile warning for mxcmmc,
drivers/mmc/host/mxcmmc.c: In function 'mxcmci_data_done':
drivers/mmc/host/mxcmmc.c:661:6: warning: variable 'data_error' set but
not used [-Wunused-but-set-variable]
The easiest method is to remove the data_error. But looking into
the code closely, I think we should check the return value of
mxcmci_finish_data as if it got data->error(the same as data_error),
we shouldn't try to read the response.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Just a trivial fix for that found by reading the code.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
if user plug out sd card slowly, finally card is plugged out but
cat /proc/partitions can find that card is still exist in kernel.
that's because alougth get card detect interrupt but CMD13 still
can get correct response(all other pins are connected expect card
detect pin).
add ops->get_cd() can avoid this issue.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
array width is on-stack and not modified and should be
made static const.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Most registers need to wait until the command is completed, not
necessarily until the bus is free. At least, R-Car 2+ SoCs can signal
that via the CBSY bit, so let's use it there instead of SCLKDIVEN to
save a little bit of delay.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Our hardware engineers confirmed that it is unnecessary to wait when
turning the clock on/off. The documentation was a tad vague, so we
used to play safe.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When defining bits, make sure we always have a reference to the register
they belong to. For now, renaming all bits properly seems too intrusive,
so at least make sure we have proper documentation.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I always anticipated this code to be not correct, but now I had a test
case to prove it. According to all documentation I have, setting the
TMIO_STOP_STP bit ever only worked during block transfers. This bit is
like manually enforcing an autocmd12 during a so far seamless transfer.
It does NOT work when the block transfer had errors. It also does NOT
work with any other cmd except block commands. For all those, CMD12 has
to be treated like any other command. So, basically, we could use this
bit only for mrq->data->stop cmds. But for these, we happily use the
autocmd12 feature using the TMIO_STOP_SEC bit. As a result, the above
bit is not useful for us and we need to treat CMD12 as a regular cmd
always. Just remove the special handling code. Note that the BSP
recognized this issue as well yet had a more cautious solution to the
problem [1]. Which is understandable but makes CMD12 handling even more
complicated.
Checked with a Renesas Salvator-X/M3-W which needed to send CMD12 when
retuning one of my SD cards.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas-bsp.git/commit/?id=2838a2ff8ca776f6d18b7fbbe75f3df8dd64183a
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Jan Klötzke <jan.kloetzke@preh.de>
Tested-by: Nguyen Viet Dung <dung.nguyen.aj@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
platform_get_irq() returns an error code, but the mxcmmc driver
ignores it and always returns -EINVAL. This is not correct,
and prevents -EPROBE_DEFER from being propagated properly.
Print error message and propagate the return value of
platform_get_irq on failure.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Local variable transfer_error is assigned to a constant value and
it is never updated again.
Remove this variable and the dead code it guards.
Addresses-Coverity-ID: 1222110
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reduce max_segs to 64, a value that allows allocation of an entire
EDMA descriptor list within a single page - EDMA descriptors
are 40 bytes and the header is much larger. This avoids doing a
higher order GFP_ATOMIC allocation in edma_prep_slave_sg
when setting up a transfer which can potentially fail due to
fragmentation under heavy I/O load.
The current value of 1024 is unusually high in comparison to
other mmc host drivers which mostly use values of between 1
and 256. The EDMA driver at present splits lists above 20
segments in any case so reducing the size of lists we pass to
it shouldn't add much overhead.
Signed-off-by: Will Newton <willn@resin.io>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a new variant of the SDHI driver to support R-Car Gen3 with DMA via
on-chip bus mastering. Since the DMAC is in a part of the SDHI module it
is not suitable to be used via DMA Engine.
Clearing of DM_CM_INFO1 after DMA thanks to Dirk Behme
Cc: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Ai Kyuse <ai.kyuse.uw@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add dataend to DMA ops to allow DMAC implementation dependent
handling of DMA data end.
Also implement the operation for SDHI.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Allow TMIO and SDHI driver implementations to provide values for
max_segs and max_blk_count.
A follow-up patch will set these values for Renesas Gen3 SoCs
the using an SDHI driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Ai Kyuse <ai.kyuse.uw@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dev_pm_ops are not supposed to change at runtime. All functions
working with dev_pm_ops provided by <linux/device.h> work with const
dev_pm_ops. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
11586 624 0 12210 2fb2 drivers/mmc/host/omap_hsmmc.o
File size After adding 'const':
text data bss dec hex filename
11778 432 0 12210 2fb2 drivers/mmc/host/omap_hsmmc.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 2a842acab1 ("block: introduce new block status code type") changed
the error type but not in patches merged through the mmc tree, like
commit 0493f6fe5b ("mmc: block: Move boot partition locking into a driver
op"). Fix one error code that is incorrect and also use BLK_STS_OK in
preference to 0.
Fixes: 17ece345a0 ("Merge tag 'mmc-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We to some extent should tolerate R1_OUT_OF_RANGE for open-ending
mode as it is expected behaviour and most of the backup partition
tables should be located near some of the last blocks which will
always make open-ending read exceed the capacity of cards.
Fixes: 9820a5b111 ("mmc: core: for data errors, take response of stop cmd into account")
Fixes: a04e6bae9e ("mmc: core: check also R1 response for stop commands")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Change the default err value to -EINVAL, make sure the card only
has type EXT_CSD_CARD_TYPE_HS400_1_8V also do the signal voltage
setting when select hs400es mode.
Fixes: commit 1720d3545b ("mmc: core: switch to 1V8 or 1V2 for hs400es mode")
Cc: <stable@vger.kernel.org>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
omap_hsmmc driver always relied on CMD12 to stop transmission.
However if CMD12 is not issued at the correct timing, the card will
indicate a out of range error. With certain cards in some of the
DRA7 based boards, -EIO error is observed. By Adding CMD23 capability,
the MMC core will send MMC_SET_BLOCK_COUNT command before
MMC_READ_MULTIPLE_BLOCK/MMC_WRITE_MULTIPLE_BLOCK commands.
commit a04e6bae9e ("mmc: core: check also R1 response for
stop commands") exposed this bug in omap_hsmmc driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit 304419d8a7 ("mmc: core: Allocate per-request data using the
block layer core") refactored mechanism of queue handling caused
mmc_init_request() can be called just after mmc_cleanup_queue() caused null
pointer dereference.
Another commit bbdc74dc19 ("mmc: block: Prevent new req entering queue
after its cleanup") tried to fix the problem. However it actually miss one
corner case.
We could still reproduce the issue mentioned with these steps:
(1) insert a SD card and mount it
(2) hotplug it, so it will leave md->usage still be counted
(3) reboot the system which will sync data and umount the card
[Unable to handle kernel NULL pointer dereference at virtual address
00000000
[user pgtable: 4k pages, 48-bit VAs, pgd = ffff80007bab3000
[[0000000000000000] *pgd=000000007a828003, *pud=0000000078dce003,
*pmd=000000007aab6003, *pte=0000000000000000
[Internal error: Oops: 96000007 [#1] PREEMPT SMP
[Modules linked in:
[CPU: 3 PID: 3507 Comm: umount Tainted: G W
4.13.0-rc1-next-20170720-00012-g9d9bf45 #33
[Hardware name: Firefly-RK3399 Board (DT)
[task: ffff80007a1de200 task.stack: ffff80007a01c000
[PC is at mmc_init_request+0x14/0xc4
[LR is at alloc_request_size+0x4c/0x74
[pc : [<ffff0000087d7150>] lr : [<ffff000008378fe0>] pstate: 600001c5
[sp : ffff80007a01f8f0
....
[[<ffff0000087d7150>] mmc_init_request+0x14/0xc4
[[<ffff000008378fe0>] alloc_request_size+0x4c/0x74
[[<ffff00000817ac28>] mempool_create_node+0xb8/0x17c
[[<ffff00000837aadc>] blk_init_rl+0x9c/0x120
[[<ffff000008396580>] blkg_alloc+0x110/0x234
[[<ffff000008396ac8>] blkg_create+0x424/0x468
[[<ffff00000839877c>] blkg_lookup_create+0xd8/0x14c
[[<ffff0000083796bc>] generic_make_request_checks+0x368/0x3b0
[[<ffff00000837b050>] generic_make_request+0x1c/0x240
So mmc_blk_put wouldn't calling blk_cleanup_queue which actually the
QUEUE_FLAG_DYING and QUEUE_FLAG_BYPASS should stay. Block core expect
blk_queue_bypass_{start, end} internally to bypass/drain the queue before
actually dying the queue, so it didn't expose API to set the queue bypass.
I think we should set QUEUE_FLAG_BYPASS whenever queue is removed, although
the md->usage is still counted, as no dispatch queue could be found then.
Fixes: 304419d8a7 ("mmc: core: Allocate per-request data using the block layer core")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When the device is non removable, the card detect signal is often used
for another purpose i.e. muxed to another SoC peripheral or used as a
GPIO. It could lead to wrong behaviors depending the default value of
this signal if not muxed to the SDHCI controller.
Fixes: bb5f8ea4d5 ("mmc: sdhci-of-at91: introduce driver for the Atmel SDMMC")
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Change to print the information about when the deprecated "num-slots" DT
binding is being used, as to avoid confusion when browsing the log:
dwmmc_rockchip fe320000.dwmmc: 'num-slots' was deprecated.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Fixes: d30a8f7bdf ("mmc: dw_mmc: deprecated the "num-slots" property")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
