dm_write_async and dm_write_reg_async are almost identical.
Move common functionality to dm_write_async_helper (saves ~256b).
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch #if 0's the following unused functions:
- espi.c:t1_espi_set_misc_ctrl()
- sge.c:t1_sched_set_max_avail_bytes()
- sge.c:t1_sched_set_drain_bits_per_us()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Support to add/delete/store/restore 64 and 128 Ethernet addresses for Xframe I and Xframe II respectively.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring secondary unicast addresses. Unicast
addresses take precendece over multicast addresses when filling
the exact address filters to avoid going to promiscous mode.
When more unicast addresses are present than filter slots,
unicast filtering is disabled and all slots can be used for
multicast addresses.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functions for reg_pattern_test and reg_set_and check
Changed macros to use these functions
Compiled x86, untested
Size decreased ~2K
old:
$ size drivers/net/e1000e/ethtool.o
text data bss dec hex filename
14461 0 0 14461 387d drivers/net/e1000e/ethtool.o
new:
$ size drivers/net/e1000e/ethtool.o
text data bss dec hex filename
12498 0 0 12498 30d2 drivers/net/e1000e/ethtool.o
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minimal macro to function conversion in e1000_ethtool.c
Adds functions reg_pattern_test and reg_set_and_check
Changes REG_PATTERN_TEST and REG_SET_AND_CHECK macros
to call these functions.
Saves ~2.5KB
Compiled x86, untested (no hardware)
old:
$ size drivers/net/e1000/e1000_ethtool.o
text data bss dec hex filename
16778 0 0 16778 418a drivers/net/e1000/e1000_ethtool.o
new:
$ size drivers/net/e1000/e1000_ethtool.o
text data bss dec hex filename
14128 0 0 14128 3730 drivers/net/e1000/e1000_ethtool.o
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
formerly e1000/e1000e only updated traffic counters once every
2 seconds with the register values of bytes/packets. With newer
code however in the interrupt and polling code we can real-time
fill in these values in the netstats struct for users to see.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
formerly e1000/e1000e only updated traffic counters once every
2 seconds with the register values of bytes/packets. With newer
code however in the interrupt and polling code we can real-time
fill in these values in the netstats struct for users to see.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the RDC R6040 MAC we can find in the RDC
R-321x System-on-chips.
Signed-off-by: Sten Wang <sten.wang@rdc.com.tw>
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
On the systems that have cache incoherent DMA, including ARM, there
is a race condition between software allocating a new receive buffer
and hardware writing into a buffer. The two race on touching the last
Receive Frame Descriptor (RFD). It has its el-bit set and its next
link equal to 0. When hardware encounters this buffer it attempts to
write data to it and then update Status Word bits and Actual Count in
the RFD. At the same time software may try to clear the el-bit and
set the link address to a new buffer.
Since the entire RFD is once cache-line, the two write operations can
collide. This can lead to the receive unit stalling or interpreting
random memory as its receive area.
The fix is to set the el-bit on and the size to 0 on the next to last
buffer in the chain. When the hardware encounters this buffer it stops
and does not write to it at all. The hardware issues an RNR interrupt
with the receive unit in the No Resources state. Software can write
to the tail of the list because it knows hardware will stop on the
previous descriptor that was marked as the end of list.
Once it has a new next to last buffer prepared, it can clear the el-bit
and set the size on the previous one. The race on this buffer is safe
since the link already points to a valid next buffer and the software
can handle the race setting the size (assuming aligned 16 bit writes
are atomic with respect to the DMA read). If the hardware sees the
el-bit cleared without the size set, it will move on to the next buffer
and skip this one. If it sees the size set but the el-bit still set,
it will complete that buffer and then RNR interrupt and wait.
Signed-off-by: David Acker <dacker@roinet.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
To quote one of my favorite contemporary author:
[include/linux/sockios.h]
* THESE IOCTLS ARE _DEPRECATED_ AND WILL DISAPPEAR IN 2.5.X -DaveM
*/
#define SIOCDEVPRIVATE 0x89F0 /* to 89FF */
[...]
Gentoo's snmpd trips up over this code when trying to figure if the driver
supports the non-SIOCDEVPRIVATE API or not. One can argue over its choice
of heuristic but there no reason to make ioctl more ugly than needed.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Jesse Huang <jesse@icplus.com.tw>
Tested-by: Volker Sauer <vsauer@dvs.tu-darmstadt.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch contains the following cleanups:
- static functions in .c files shouldn't be marked inline
- make needlessly global code static
- #if 0 unused code
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
While cleaning up the internal API focussing on Fiber and CX4 code
we found that I had broken the copper PHY initialization code. This
patch restores the PHY-specific code. This is mostly uninteresting
since no copper PHY boards are yet available. The changes have been
tested against Fiber only as I do not even have copper PHY versions
of 82598 macs.
This change actually cleans up the API code a bit more and we
lose some initialization code. A few PHY link detection helper
lines of code have been snuck into this patch, as well as a
read flush where it was suspected that this might cause issues.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
e1000e will from now on support the PCI-Express adapters that
previously were supported by e1000. This support means better
performance and easier debugging from now on for both the old
PCI-X/PCI hardware and PCI-Express adapters.
This patch also moves 3 recently merged device IDs over to e1000e
that are identical to quad-port versions of already existing
dual port versions. With this last bit every former e1000 pci-e
device should work now with e1000e.
Here is a brief list of which gigabit driver to use with which
adapter:
e1000:
82540 -> 82547
e1000e:
82571 -> 82573
ich8, ich9 (82562 or 82566)
es2lan (80003eslan)
igb: (not yet merged, only available from e1000.sf.net)
82575
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
L1 ASPM link (pci-e link power savings) has significant benefits
(~1W savings when link is active) but unfortunately does not work
correctly on any of the chipsets that have 82573 on mobile platforms
which causes various nuisances:
- eeprom reads return garbage information leading to bad eeprom
checksums
- long ping times (up to 2 seconds)
- complete system hangs (freeze/lockup)
A lot of T60 owners have been plagued by this, but other mobile
solutions also suffer from these symptoms.
Disabling L1 ASPM before we activate the PCI-E link fixes all of
these issues at the cost of some power consumption.
Remove a workaround RDTR adjustment that is no longer needed with
this new one.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Port alternate MAC address support from the sourceforge
e1000 driver to the upstream e1000e driver.
Signed-off-by: Bill Hayes <bill.hayes@hp.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* use irq_handler_t where appropriate
* no need to use 'irq' function arg, its already stored in a data struct
* rename irq handler 'irq' argument to 'dummy', where the function
has been analyzed and proven not to use its first argument.
* remove always-false "dev_id == NULL" test from irq handlers
* remove pointless casts from void*
* declance: irq argument is not const
* add KERN_xxx printk prefix
* fix minor whitespace weirdness
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This converts uses of ARRAY_SIZE(), and while at it also kills
unreachable code as far as I can say. I can't tell what was the author
trying to do with the following check. First we have:
PNMI_STATIC const SK_PNMI_STATADDR
StatAddr[SK_PNMI_MAX_IDX][SK_PNMI_MAC_TYPES];
and then a check goes like this:
if (SK_PNMI_MAX_IDX !=
(sizeof(StatAddr) / (sizeof(SK_PNMI_STATADDR) * SK_PNMI_MAC_TYPES)))
with the second line being just ARRAY_SIZE(StatAddr), which will always
return SK_PNMI_MAX_IDX, rendering the check useless.
Signed-off-by: Alejandro Martinez Ruiz <alex@flawedcode.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Using ARRAY_SIZE() on arrays of the form array[][K] makes it unnecessary
to know the value of K when checking its size.
Signed-off-by: Alejandro Martinez Ruiz <alex@flawedcode.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Move wlan_postpone_association_work() and wlan_cancel_association_work()
from a assoc.h file to the sole user, into wext.c.
Renamed those two functions to to libertas_XXX as well.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable interrupts in the iwl4965 before calling request_irq() for
the case that the previous OS or the BIOS left a pending interrupt in
the chip. This behavior has been observed on some laptops such as T61
Thinkpads and Toshiba Portege R500
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When there are 2 linked structures, using a temporary variable to hold a pointer
to the often used structure usually produces better code (smaller and faster)
since compiler does not have to constantly re-fetch data from the first structure.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bring scan result handling more in line with drivers like ipw. Scan
results are aggregated and a BSS dropped after 15 seconds if no beacon
is received. This allows the driver to interact better with userspace
where more than one process may request scans or results at any time.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a consistent naming scheme for the ops.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the limits provided by mac80211.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Put all access to wl->current_dev under protection of the mutex.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't need the set_key callback, as we don't do hw crypto.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement much easier and more lightweight locking for
the periodic work. This also removes the last big busywait
loop and replaces it by a sleeping loop.
This patch for b43legacy is patterned aftar the same patch
for b43 by Michael Buesch <mb@bu3sch.de>.
Signed-off-by: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the direct call to rfkill on an rfkill event
and replaces it with an input device. This way userspace is also
notified about the event.
This patch is the port to b43legacy of a patch for b43 by Michael Buesch
<mb@bu3sch.de>.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds full support for the RFKILL button and the RFKILL LED trigger.
This is a port to b43legacy of a patch by Michael Buesch <mb@bu3sch.de>
for b43.
Signed-off-by: Larry Finger<Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drive the LEDs through the generic LED triggers.
The patch to b43 by Michael Buesch <mb@bu3sch.de> has been ported to b43legacy.
Signed-off-by: Larry Finger <larry.finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
