When we jump to free_pcpu on failure in alloc_netdev_mqs()
rx and tx queues are not yet allocated, so no need to free them.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_alb.c
drivers/net/ethernet/altera/altera_msgdma.c
drivers/net/ethernet/altera/altera_sgdma.c
net/ipv6/xfrm6_output.c
Several cases of overlapping changes.
The xfrm6_output.c has a bug fix which overlaps the renaming
of skb->local_df to skb->ignore_df.
In the Altera TSE driver cases, the register access cleanups
in net-next overlapped with bug fixes done in net.
Similarly a bug fix to send ALB packets in the bonding driver using
the right source address overlaps with cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to commit fbd929f2dc
bonding: support QinQ for bond arp interval
the arp monitoring code allowed for proper detection of devices
stacked on top of vlans. Since the above commit, the
code can still detect a device stacked on top of single
vlan, but not a device stacked on top of Q-in-Q configuration.
The search will only set the inner vlan tag if the route
device is the vlan device. However, this is not always the
case, as it is possible to extend the stacked configuration.
With this patch it is possible to provision devices on
top Q-in-Q vlan configuration that should be used as
a source of ARP monitoring information.
For example:
ip link add link bond0 vlan10 type vlan proto 802.1q id 10
ip link add link vlan10 vlan100 type vlan proto 802.1q id 100
ip link add link vlan100 type macvlan
Note: This patch limites the number of stacked VLANs to 2,
just like before. The original, however had another issue
in that if we had more then 2 levels of VLANs, we would end
up generating incorrectly tagged traffic. This is no longer
possible.
Fixes: fbd929f2dc (bonding: support QinQ for bond arp interval)
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@redhat.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Ding Tianhong <dingtianhong@huawei.com>
CC: Patric McHardy <kaber@trash.net>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit dc8eaaa006.
vlan: Fix lockdep warning when vlan dev handle notification
Instead we use the new new API to find the lock subclass of
our vlan device. This way we can support configurations where
vlans are interspersed with other devices:
bond -> vlan -> macvlan -> vlan
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multiple devices in the kernel can be stacked/nested and they
need to know their nesting level for the purposes of lockdep.
This patch provides a generic function that determines a nesting
level of a particular device by its type (ex: vlan, macvlan, etc).
We only care about nesting of the same type of devices.
For example:
eth0 <- vlan0.10 <- macvlan0 <- vlan1.20
The nesting level of vlan1.20 would be 1, since there is another vlan
in the stack under it.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting from linux-3.13, GRO attempts to build full size skbs.
Problem is the commit assumed one particular field in skb->cb[]
was clean, but it is not the case on some stacked devices.
Timo reported a crash in case traffic is decrypted before
reaching a GRE device.
Fix this by initializing NAPI_GRO_CB(skb)->last at the right place,
this also removes one conditional.
Thanks a lot to Timo for providing full reports and bisecting this.
Fixes: 8a29111c7c ("net: gro: allow to build full sized skb")
Bisected-by: Timo Teras <timo.teras@iki.fi>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Cong Wang <cwang@twopensource.com>
commit 50624c934d (net: Delay default_device_exit_batch until no
devices are unregistering) introduced rtnl_lock_unregistering() for
default_device_exit_batch(). Same race could happen we when rmmod a driver
which calls rtnl_link_unregister() as we call dev->destructor without rtnl
lock.
For long term, I think we should clean up the mess of netdev_run_todo()
and net namespce exit code.
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/altera/altera_sgdma.c
net/netlink/af_netlink.c
net/sched/cls_api.c
net/sched/sch_api.c
The netlink conflict dealt with moving to netlink_capable() and
netlink_ns_capable() in the 'net' tree vs. supporting 'tc' operations
in non-init namespaces. These were simple transformations from
netlink_capable to netlink_ns_capable.
The Altera driver conflict was simply code removal overlapping some
void pointer cast cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit d206940319,
there are no more callers.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes ordering of rtnl notifications during unregister_netdevice
by moving RTM_DELLINK notification to until after ndo_uninit.
The problem was seen with unregistering bond netdevices.
bond ndo_uninit callback generates a few RTM_NEWLINK notifications for
NETDEV_CHANGEADDR and NETDEV_FEAT_CHANGE. This is seen mostly when the
bond is deleted with slaves still enslaved to the bond.
During unregister netdevice (rollback_registered_many to be specific)
bond ndo_uninit is called after RTM_DELLINK notification goes out.
This results in userspace seeing RTM_DELLINK followed by a couple of
RTM_NEWLINK's.
In userspace problem was seen with libnl. libnl cache deletes the bond
when it sees RTM_DELLINK and re-adds the bond with the following
RTM_NEWLINK. Resulting in a stale bond entry in libnl cache when the kernel
has already deleted the bond.
This patch has been tested for bond, bridges and vlan devices.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the helper __dev_forward_skb which is identical to
dev_forward_skb except that it doesn't actually inject the skb into
the stack. This is useful where we wish to have finer control over
how the packet is injected, e.g., via netif_rx_ni or netif_receive_skb.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I open the LOCKDEP config and run these steps:
modprobe 8021q
vconfig add eth2 20
vconfig add eth2.20 30
ifconfig eth2 xx.xx.xx.xx
then the Call Trace happened:
[32524.386288] =============================================
[32524.386293] [ INFO: possible recursive locking detected ]
[32524.386298] 3.14.0-rc2-0.7-default+ #35 Tainted: G O
[32524.386302] ---------------------------------------------
[32524.386306] ifconfig/3103 is trying to acquire lock:
[32524.386310] (&vlan_netdev_addr_lock_key/1){+.....}, at: [<ffffffff814275f4>] dev_mc_sync+0x64/0xb0
[32524.386326]
[32524.386326] but task is already holding lock:
[32524.386330] (&vlan_netdev_addr_lock_key/1){+.....}, at: [<ffffffff8141af83>] dev_set_rx_mode+0x23/0x40
[32524.386341]
[32524.386341] other info that might help us debug this:
[32524.386345] Possible unsafe locking scenario:
[32524.386345]
[32524.386350] CPU0
[32524.386352] ----
[32524.386354] lock(&vlan_netdev_addr_lock_key/1);
[32524.386359] lock(&vlan_netdev_addr_lock_key/1);
[32524.386364]
[32524.386364] *** DEADLOCK ***
[32524.386364]
[32524.386368] May be due to missing lock nesting notation
[32524.386368]
[32524.386373] 2 locks held by ifconfig/3103:
[32524.386376] #0: (rtnl_mutex){+.+.+.}, at: [<ffffffff81431d42>] rtnl_lock+0x12/0x20
[32524.386387] #1: (&vlan_netdev_addr_lock_key/1){+.....}, at: [<ffffffff8141af83>] dev_set_rx_mode+0x23/0x40
[32524.386398]
[32524.386398] stack backtrace:
[32524.386403] CPU: 1 PID: 3103 Comm: ifconfig Tainted: G O 3.14.0-rc2-0.7-default+ #35
[32524.386409] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007
[32524.386414] ffffffff81ffae40 ffff8800d9625ae8 ffffffff814f68a2 ffff8800d9625bc8
[32524.386421] ffffffff810a35fb ffff8800d8a8d9d0 00000000d9625b28 ffff8800d8a8e5d0
[32524.386428] 000003cc00000000 0000000000000002 ffff8800d8a8e5f8 0000000000000000
[32524.386435] Call Trace:
[32524.386441] [<ffffffff814f68a2>] dump_stack+0x6a/0x78
[32524.386448] [<ffffffff810a35fb>] __lock_acquire+0x7ab/0x1940
[32524.386454] [<ffffffff810a323a>] ? __lock_acquire+0x3ea/0x1940
[32524.386459] [<ffffffff810a4874>] lock_acquire+0xe4/0x110
[32524.386464] [<ffffffff814275f4>] ? dev_mc_sync+0x64/0xb0
[32524.386471] [<ffffffff814fc07a>] _raw_spin_lock_nested+0x2a/0x40
[32524.386476] [<ffffffff814275f4>] ? dev_mc_sync+0x64/0xb0
[32524.386481] [<ffffffff814275f4>] dev_mc_sync+0x64/0xb0
[32524.386489] [<ffffffffa0500cab>] vlan_dev_set_rx_mode+0x2b/0x50 [8021q]
[32524.386495] [<ffffffff8141addf>] __dev_set_rx_mode+0x5f/0xb0
[32524.386500] [<ffffffff8141af8b>] dev_set_rx_mode+0x2b/0x40
[32524.386506] [<ffffffff8141b3cf>] __dev_open+0xef/0x150
[32524.386511] [<ffffffff8141b177>] __dev_change_flags+0xa7/0x190
[32524.386516] [<ffffffff8141b292>] dev_change_flags+0x32/0x80
[32524.386524] [<ffffffff8149ca56>] devinet_ioctl+0x7d6/0x830
[32524.386532] [<ffffffff81437b0b>] ? dev_ioctl+0x34b/0x660
[32524.386540] [<ffffffff814a05b0>] inet_ioctl+0x80/0xa0
[32524.386550] [<ffffffff8140199d>] sock_do_ioctl+0x2d/0x60
[32524.386558] [<ffffffff81401a52>] sock_ioctl+0x82/0x2a0
[32524.386568] [<ffffffff811a7123>] do_vfs_ioctl+0x93/0x590
[32524.386578] [<ffffffff811b2705>] ? rcu_read_lock_held+0x45/0x50
[32524.386586] [<ffffffff811b39e5>] ? __fget_light+0x105/0x110
[32524.386594] [<ffffffff811a76b1>] SyS_ioctl+0x91/0xb0
[32524.386604] [<ffffffff815057e2>] system_call_fastpath+0x16/0x1b
========================================================================
The reason is that all of the addr_lock_key for vlan dev have the same class,
so if we change the status for vlan dev, the vlan dev and its real dev will
hold the same class of addr_lock_key together, so the warning happened.
we should distinguish the lock depth for vlan dev and its real dev.
v1->v2: Convert the vlan_netdev_addr_lock_key to an array of eight elements, which
could support to add 8 vlan id on a same vlan dev, I think it is enough for current
scene, because a netdev's name is limited to IFNAMSIZ which could not hold 8 vlan id,
and the vlan dev would not meet the same class key with its real dev.
The new function vlan_dev_get_lockdep_subkey() will return the subkey and make the vlan
dev could get a suitable class key.
v2->v3: According David's suggestion, I use the subclass to distinguish the lock key for vlan dev
and its real dev, but it make no sense, because the difference for subclass in the
lock_class_key doesn't mean that the difference class for lock_key, so I use lock_depth
to distinguish the different depth for every vlan dev, the same depth of the vlan dev
could have the same lock_class_key, I import the MAX_LOCK_DEPTH from the include/linux/sched.h,
I think it is enough here, the lockdep should never exceed that value.
v3->v4: Add a huge array of locking keys will waste static kernel memory and is not a appropriate method,
we could use _nested() variants to fix the problem, calculate the depth for every vlan dev,
and use the depth as the subclass for addr_lock_key.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes, when the packet arrives at skb_mac_gso_segment()
its skb->mac_len already accounts for some of the mac lenght
headers in the packet. This seems to happen when forwarding
through and OpenSSL tunnel.
When we start looking for any vlan headers in skb_network_protocol()
we seem to ignore any of the already known mac headers and start
with an ETH_HLEN. This results in an incorrect offset, dropped
TSO frames and general slowness of the connection.
We can start counting from the known skb->mac_len
and return at least that much if all mac level headers
are known and accounted for.
Fixes: 53d6471cef (net: Account for all vlan headers in skb_mac_gso_segment)
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Daniel Borkman <dborkman@redhat.com>
Tested-by: Martin Filip <nexus+kernel@smoula.net>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we're checking a variable for != NULL after actually
dereferencing it, in netdev_lower_get_next_private*().
It's counter-intuitive at best, and can lead to faulty usage (as it implies
that the variable can be NULL), so fix it by removing the useless checks.
Reported-by: Daniel Borkmann <dborkman@redhat.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Eric Dumazet <edumazet@google.com>
CC: Nicolas Dichtel <nicolas.dichtel@6wind.com>
CC: Jiri Pirko <jiri@resnulli.us>
CC: stephen hemminger <stephen@networkplumber.org>
CC: Jerry Chu <hkchu@google.com>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recycling skb always had been very tough...
This time it appears GRO layer can accumulate skb->truesize
adjustments made by drivers when they attach a fragment to skb.
skb_gro_receive() can only subtract from skb->truesize the used part
of a fragment.
I spotted this problem seeing TcpExtPruneCalled and
TcpExtTCPRcvCollapsed that were unexpected with a recent kernel, where
TCP receive window should be sized properly to accept traffic coming
from a driver not overshooting skb->truesize.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there is no way how to find out if a device supports busy
polling. So add a feature and make it dependent on ndo_busy_poll
existence.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Here is my initial pull request for the networking subsystem during
this merge window:
1) Support for ESN in AH (RFC 4302) from Fan Du.
2) Add full kernel doc for ethtool command structures, from Ben
Hutchings.
3) Add BCM7xxx PHY driver, from Florian Fainelli.
4) Export computed TCP rate information in netlink socket dumps, from
Eric Dumazet.
5) Allow IPSEC SA to be dumped partially using a filter, from Nicolas
Dichtel.
6) Convert many drivers to pci_enable_msix_range(), from Alexander
Gordeev.
7) Record SKB timestamps more efficiently, from Eric Dumazet.
8) Switch to microsecond resolution for TCP round trip times, also
from Eric Dumazet.
9) Clean up and fix 6lowpan fragmentation handling by making use of
the existing inet_frag api for it's implementation.
10) Add TX grant mapping to xen-netback driver, from Zoltan Kiss.
11) Auto size SKB lengths when composing netlink messages based upon
past message sizes used, from Eric Dumazet.
12) qdisc dumps can take a long time, add a cond_resched(), From Eric
Dumazet.
13) Sanitize netpoll core and drivers wrt. SKB handling semantics.
Get rid of never-used-in-tree netpoll RX handling. From Eric W
Biederman.
14) Support inter-address-family and namespace changing in VTI tunnel
driver(s). From Steffen Klassert.
15) Add Altera TSE driver, from Vince Bridgers.
16) Optimizing csum_replace2() so that it doesn't adjust the checksum
by checksumming the entire header, from Eric Dumazet.
17) Expand BPF internal implementation for faster interpreting, more
direct translations into JIT'd code, and much cleaner uses of BPF
filtering in non-socket ocntexts. From Daniel Borkmann and Alexei
Starovoitov"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1976 commits)
netpoll: Use skb_irq_freeable to make zap_completion_queue safe.
net: Add a test to see if a skb is freeable in irq context
qlcnic: Fix build failure due to undefined reference to `vxlan_get_rx_port'
net: ptp: move PTP classifier in its own file
net: sxgbe: make "core_ops" static
net: sxgbe: fix logical vs bitwise operation
net: sxgbe: sxgbe_mdio_register() frees the bus
Call efx_set_channels() before efx->type->dimension_resources()
xen-netback: disable rogue vif in kthread context
net/mlx4: Set proper build dependancy with vxlan
be2net: fix build dependency on VxLAN
mac802154: make csma/cca parameters per-wpan
mac802154: allow only one WPAN to be up at any given time
net: filter: minor: fix kdoc in __sk_run_filter
netlink: don't compare the nul-termination in nla_strcmp
can: c_can: Avoid led toggling for every packet.
can: c_can: Simplify TX interrupt cleanup
can: c_can: Store dlc private
can: c_can: Reduce register access
can: c_can: Make the code readable
...
Pull core block layer updates from Jens Axboe:
"This is the pull request for the core block IO bits for the 3.15
kernel. It's a smaller round this time, it contains:
- Various little blk-mq fixes and additions from Christoph and
myself.
- Cleanup of the IPI usage from the block layer, and associated
helper code. From Frederic Weisbecker and Jan Kara.
- Duplicate code cleanup in bio-integrity from Gu Zheng. This will
give you a merge conflict, but that should be easy to resolve.
- blk-mq notify spinlock fix for RT from Mike Galbraith.
- A blktrace partial accounting bug fix from Roman Pen.
- Missing REQ_SYNC detection fix for blk-mq from Shaohua Li"
* 'for-3.15/core' of git://git.kernel.dk/linux-block: (25 commits)
blk-mq: add REQ_SYNC early
rt,blk,mq: Make blk_mq_cpu_notify_lock a raw spinlock
blk-mq: support partial I/O completions
blk-mq: merge blk_mq_insert_request and blk_mq_run_request
blk-mq: remove blk_mq_alloc_rq
blk-mq: don't dump CPU -> hw queue map on driver load
blk-mq: fix wrong usage of hctx->state vs hctx->flags
blk-mq: allow blk_mq_init_commands() to return failure
block: remove old blk_iopoll_enabled variable
blktrace: fix accounting of partially completed requests
smp: Rename __smp_call_function_single() to smp_call_function_single_async()
smp: Remove wait argument from __smp_call_function_single()
watchdog: Simplify a little the IPI call
smp: Move __smp_call_function_single() below its safe version
smp: Consolidate the various smp_call_function_single() declensions
smp: Teach __smp_call_function_single() to check for offline cpus
smp: Remove unused list_head from csd
smp: Iterate functions through llist_for_each_entry_safe()
block: Stop abusing rq->csd.list in blk-softirq
block: Remove useless IPI struct initialization
...
Main difference between napi_frags_skb() and napi_gro_receive() is that
the later is called while ethernet header was already pulled by the NIC
driver (eth_type_trans() was called before napi_gro_receive())
Jerry Chu in commit 299603e837 ("net-gro: Prepare GRO stack for the
upcoming tunneling support") tried to remove this difference by calling
eth_type_trans() from napi_frags_skb() instead of doing this later from
napi_frags_finish()
Goal was that napi_gro_complete() could call
ptype->callbacks.gro_complete(skb, 0) (offset of first network header =
0)
Also, xxx_gro_receive() handlers all use off = skb_gro_offset(skb) to
point to their own header, for the current skb and ones held in gro_list
Problem is this cleanup work defeated the frag0 optimization:
It turns out the consecutive pskb_may_pull() calls are too expensive.
This patch brings back the frag0 stuff in napi_frags_skb().
As all skb have their mac header in skb head, we no longer need
skb_gro_mac_header()
Reported-by: Michal Schmidt <mschmidt@redhat.com>
Fixes: 299603e837 ("net-gro: Prepare GRO stack for the upcoming tunneling support")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jerry Chu <hkchu@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/marvell/mvneta.c
The mvneta.c conflict is a case of overlapping changes,
a conversion to devm_ioremap_resource() vs. a conversion
to netdev_alloc_pcpu_stats.
Signed-off-by: David S. Miller <davem@davemloft.net>
The netpoll_rx_enable and netpoll_rx_disable functions have always
controlled polling the network drivers transmit and receive queues.
Rename them to netpoll_poll_enable and netpoll_poll_disable to make
their functionality clear.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Today netpoll_rx_enable and netpoll_rx_disable are called from
dev_close and and __dev_close, and not from dev_close_many.
Move the calls into __dev_close_many so that we have a single call
site to maintain, and so that dev_close_many gains this protection as
well. Which importantly makes batched network device deletes safe.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_network_protocol() already accounts for multiple vlan
headers that may be present in the skb. However, skb_mac_gso_segment()
doesn't know anything about it and assumes that skb->mac_len
is set correctly to skip all mac headers. That may not
always be the case. If we are simply forwarding the packet (via
bridge or macvtap), all vlan headers may not be accounted for.
A simple solution is to allow skb_network_protocol to return
the vlan depth it has calculated. This way skb_mac_gso_segment
will correctly skip all mac headers.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dropping packets in __dev_queue_xmit() when transmit queue
is stopped (NIC TX ring buffer full or BQL limit reached) currently
outputs a syslog message.
It would be better to get a precise count of such events available in
netdevice stats so that monitoring tools can have a clue.
This extends the work done in caf586e5f2
("net: add a core netdev->rx_dropped counter")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The packet hash can be considered a property of the packet, not just
on RX path.
This patch changes name of rxhash and l4_rxhash skbuff fields to be
hash and l4_hash respectively. This includes changing uses of the
field in the code which don't call the access functions.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netpoll packet receive code only becomes active if the netpoll
rx_skb_hook is implemented, and there is not a single implementation
of the netpoll rx_skb_hook in the kernel.
All of the out of tree implementations I have found all call
netpoll_poll which was removed from the kernel in 2011, so this
change should not add any additional breakage.
There are problems with the netpoll packet receive code. __netpoll_rx
does not call dev_kfree_skb_irq or dev_kfree_skb_any in hard irq
context. netpoll_neigh_reply leaks every skb it receives. Reception
of packets does not work successfully on stacked devices (aka bonding,
team, bridge, and vlans).
Given that the netpoll packet receive code is buggy, there are no
out of tree users that will be merged soon, and the code has
not been used for in tree for a decade let's just remove it.
Reverting this commit can server as a starting point for anyone
who wants to resurrect netpoll packet reception support.
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of __constant_<foo> has been unnecessary for quite awhile now.
Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The name __smp_call_function_single() doesn't tell much about the
properties of this function, especially when compared to
smp_call_function_single().
The comments above the implementation are also misleading. The main
point of this function is actually not to be able to embed the csd
in an object. This is actually a requirement that result from the
purpose of this function which is to raise an IPI asynchronously.
As such it can be called with interrupts disabled. And this feature
comes at the cost of the caller who then needs to serialize the
IPIs on this csd.
Lets rename the function and enhance the comments so that they reflect
these properties.
Suggested-by: Christoph Hellwig <hch@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Jens Axboe <axboe@fb.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The main point of calling __smp_call_function_single() is to send
an IPI in a pure asynchronous way. By embedding a csd in an object,
a caller can send the IPI without waiting for a previous one to complete
as is required by smp_call_function_single() for example. As such,
sending this kind of IPI can be safe even when irqs are disabled.
This flexibility comes at the expense of the caller who then needs to
synchronize the csd lifecycle by himself and make sure that IPIs on a
single csd are serialized.
This is how __smp_call_function_single() works when wait = 0 and this
usecase is relevant.
Now there don't seem to be any usecase with wait = 1 that can't be
covered by smp_call_function_single() instead, which is safer. Lets look
at the two possible scenario:
1) The user calls __smp_call_function_single(wait = 1) on a csd embedded
in an object. It looks like a nice and convenient pattern at the first
sight because we can then retrieve the object from the IPI handler easily.
But actually it is a waste of memory space in the object since the csd
can be allocated from the stack by smp_call_function_single(wait = 1)
and the object can be passed an the IPI argument.
Besides that, embedding the csd in an object is more error prone
because the caller must take care of the serialization of the IPIs
for this csd.
2) The user calls __smp_call_function_single(wait = 1) on a csd that
is allocated on the stack. It's ok but smp_call_function_single()
can do it as well and it already takes care of the allocation on the
stack. Again it's more simple and less error prone.
Therefore, using the underscore prepend API version with wait = 1
is a bad pattern and a sign that the caller can do safer and more
simple.
There was a single user of that which has just been converted.
So lets remove this option to discourage further users.
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jan Kara <jack@suse.cz>
Cc: Jens Axboe <axboe@fb.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch fix spelling typo in Documentation/DocBook.
It is because .html and .xml files are generated by make htmldocs,
I have to fix a typo within the source files.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Will be used by upcoming ipv4 forward path change that needs to
determine feature mask using skb->dst->dev instead of skb->dev.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark functions as static in core/dev.c because they are not used outside
this file.
This eliminates the following warning in core/dev.c:
net/core/dev.c:2806:5: warning: no previous prototype for ‘__dev_queue_xmit’ [-Wmissing-prototypes]
net/core/dev.c:4640:5: warning: no previous prototype for ‘netdev_adjacent_sysfs_add’ [-Wmissing-prototypes]
net/core/dev.c:4650:6: warning: no previous prototype for ‘netdev_adjacent_sysfs_del’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Reviewed-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) BPF debugger and asm tool by Daniel Borkmann.
2) Speed up create/bind in AF_PACKET, also from Daniel Borkmann.
3) Correct reciprocal_divide and update users, from Hannes Frederic
Sowa and Daniel Borkmann.
4) Currently we only have a "set" operation for the hw timestamp socket
ioctl, add a "get" operation to match. From Ben Hutchings.
5) Add better trace events for debugging driver datapath problems, also
from Ben Hutchings.
6) Implement auto corking in TCP, from Eric Dumazet. Basically, if we
have a small send and a previous packet is already in the qdisc or
device queue, defer until TX completion or we get more data.
7) Allow userspace to manage ipv6 temporary addresses, from Jiri Pirko.
8) Add a qdisc bypass option for AF_PACKET sockets, from Daniel
Borkmann.
9) Share IP header compression code between Bluetooth and IEEE802154
layers, from Jukka Rissanen.
10) Fix ipv6 router reachability probing, from Jiri Benc.
11) Allow packets to be captured on macvtap devices, from Vlad Yasevich.
12) Support tunneling in GRO layer, from Jerry Chu.
13) Allow bonding to be configured fully using netlink, from Scott
Feldman.
14) Allow AF_PACKET users to obtain the VLAN TPID, just like they can
already get the TCI. From Atzm Watanabe.
15) New "Heavy Hitter" qdisc, from Terry Lam.
16) Significantly improve the IPSEC support in pktgen, from Fan Du.
17) Allow ipv4 tunnels to cache routes, just like sockets. From Tom
Herbert.
18) Add Proportional Integral Enhanced packet scheduler, from Vijay
Subramanian.
19) Allow openvswitch to mmap'd netlink, from Thomas Graf.
20) Key TCP metrics blobs also by source address, not just destination
address. From Christoph Paasch.
21) Support 10G in generic phylib. From Andy Fleming.
22) Try to short-circuit GRO flow compares using device provided RX
hash, if provided. From Tom Herbert.
The wireless and netfilter folks have been busy little bees too.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2064 commits)
net/cxgb4: Fix referencing freed adapter
ipv6: reallocate addrconf router for ipv6 address when lo device up
fib_frontend: fix possible NULL pointer dereference
rtnetlink: remove IFLA_BOND_SLAVE definition
rtnetlink: remove check for fill_slave_info in rtnl_have_link_slave_info
qlcnic: update version to 5.3.55
qlcnic: Enhance logic to calculate msix vectors.
qlcnic: Refactor interrupt coalescing code for all adapters.
qlcnic: Update poll controller code path
qlcnic: Interrupt code cleanup
qlcnic: Enhance Tx timeout debugging.
qlcnic: Use bool for rx_mac_learn.
bonding: fix u64 division
rtnetlink: add missing IFLA_BOND_AD_INFO_UNSPEC
sfc: Use the correct maximum TX DMA ring size for SFC9100
Add Shradha Shah as the sfc driver maintainer.
net/vxlan: Share RX skb de-marking and checksum checks with ovs
tulip: cleanup by using ARRAY_SIZE()
ip_tunnel: clear IPCB in ip_tunnel_xmit() in case dst_link_failure() is called
net/cxgb4: Don't retrieve stats during recovery
...
Pull trivial tree updates from Jiri Kosina:
"Usual rocket science stuff from trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
neighbour.h: fix comment
sched: Fix warning on make htmldocs caused by wait.h
slab: struct kmem_cache is protected by slab_mutex
doc: Fix typo in USB Gadget Documentation
of/Kconfig: Spelling s/one/once/
mkregtable: Fix sscanf handling
lp5523, lp8501: comment improvements
thermal: rcar: comment spelling
treewide: fix comments and printk msgs
IXP4xx: remove '1 &&' from a condition check in ixp4xx_restart()
Documentation: update /proc/uptime field description
Documentation: Fix size parameter for snprintf
arm: fix comment header and macro name
asm-generic: uaccess: Spelling s/a ny/any/
mtd: onenand: fix comment header
doc: driver-model/platform.txt: fix a typo
drivers: fix typo in DEVTMPFS_MOUNT Kconfig help text
doc: Fix typo (acces_process_vm -> access_process_vm)
treewide: Fix typos in printk
drivers/gpu/drm/qxl/Kconfig: reformat the help text
...
Export the gro_find_receive/complete_by_type helpers to they can be invoked
by the gro callbacks of encapsulation protocols such as vxlan.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add GRO handlers for protocols that do UDP encapsulation, with the intent of
being able to coalesce packets which encapsulate packets belonging to
the same TCP session.
For GRO purposes, the destination UDP port takes the role of the ether type
field in the ethernet header or the next protocol in the IP header.
The UDP GRO handler will only attempt to coalesce packets whose destination
port is registered to have gro handler.
Use a mark on the skb GRO CB data to disallow (flush) running the udp gro receive
code twice on a packet. This solves the problem of udp encapsulated packets whose
inner VM packet is udp and happen to carry a port which has registered offloads.
Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
softnet_data is already set to 0, no need to use memset or initialize
specific fields to 0 or NULL afterwards.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
To silent "make htmldocs" warning.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend existing support for netdevice receive queue sysfs attributes to
permit a device-specific attribute group. Initial use case for this
support will be to allow the virtio-net device to export per-receive
queue mergeable receive buffer size.
Signed-off-by: Michael Dalton <mwdalton@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if a device changes its mtu, first the change happens (invloving
all the side effects), and after that the NETDEV_CHANGEMTU is sent so that
other devices can catch up with the new mtu. However, if they return
NOTIFY_BAD, then the change is reverted and error returned.
This is a really long and costy operation (sometimes). To fix this, add
NETDEV_PRECHANGEMTU notification which is called prior to any change
actually happening, and if any callee returns NOTIFY_BAD - the change is
aborted. This way we're skipping all the playing with apply/revert the mtu.
CC: "David S. Miller" <davem@davemloft.net>
CC: Jiri Pirko <jiri@resnulli.us>
CC: Eric Dumazet <edumazet@google.com>
CC: Nicolas Dichtel <nicolas.dichtel@6wind.com>
CC: Cong Wang <amwang@redhat.com>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
When initializing a gro_list for a packet, first check the rxhash of
the incoming skb against that of the skb's in the list. This should be
a very strong inidicator of whether the flow is going to be matched,
and potentially allows a lot of other checks to be short circuited.
Use skb_hash_raw so that we don't force the hash to be calculated.
Tested by running netperf 200 TCP_STREAMs between two machines with
GRO, HW rxhash, and 1G. Saw no performance degration, slight reduction
of time in dev_gro_receive.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we don't rename the upper/lower_ifc symlinks in
/sys/class/net/*/ , which might result stale/duplicate links/names.
Fix this by adding netdev_adjacent_rename_links(dev, oldname) which renames
all the upper/lower interface's links to dev from the upper/lower_oldname
to the new name.
We don't need a rollback because only we control these symlinks and if we
fail to rename them - sysfs will anyway complain.
Reported-by: Ding Tianhong <dingtianhong@huawei.com>
CC: Ding Tianhong <dingtianhong@huawei.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Eric Dumazet <edumazet@google.com>
CC: Nicolas Dichtel <nicolas.dichtel@6wind.com>
CC: Cong Wang <amwang@redhat.com>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
They clean up the code a bit and can be used further.
CC: Ding Tianhong <dingtianhong@huawei.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Eric Dumazet <edumazet@google.com>
CC: Nicolas Dichtel <nicolas.dichtel@6wind.com>
CC: Cong Wang <amwang@redhat.com>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing net/netif_rx and net/netif_receive_skb trace events
provide little information about the skb, nor do they indicate how it
entered the stack.
Add trace events at entry of each of the exported functions, including
most fields that are likely to be interesting for debugging driver
datapath behaviour. Split netif_rx() and netif_receive_skb() so that
internal calls are not traced.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing net/net_dev_xmit trace event provides little information
about the skb that has been passed to the driver, and it is not
simple to add more since the skb may already have been freed at
the point the event is emitted.
Add a separate trace event before the skb is passed to the driver,
including most fields that are likely to be interesting for debugging
driver datapath behaviour.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
