Pull x86 apic updates from Thomas Gleixner:
"After stopping the full x86/apic branch, I took some time to go
through the first block of patches again, which are mostly cleanups
and preparatory work for the irqdomain conversion and ioapic hotplug
support.
Unfortunaly one of the real problematic commits was right at the
beginning, so I rebased this portion of the pending patches without
the offenders.
It would be great to get this into 3.19. That makes reworking the
problematic parts simpler. The usual tip testing did not unearth any
issues and it is fully bisectible now.
I'm pretty confident that this wont affect the calmness of the xmas
season.
Changes:
- Split the convoluted io_apic.c code into domain specific parts
(vector, ioapic, msi, htirq)
- Introduce proper helper functions to retrieve irq specific data
instead of open coded dereferencing of pointers
- Preparatory work for ioapic hotplug and irqdomain conversion
- Removal of the non functional pci-ioapic driver
- Removal of unused irq entry stubs
- Make native_smp_prepare_cpus() preemtible to avoid GFP_ATOMIC
allocations for everything which is called from there.
- Small cleanups and fixes"
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
iommu/amd: Use helpers to access irq_cfg data structure associated with IRQ
iommu/vt-d: Use helpers to access irq_cfg data structure associated with IRQ
x86: irq_remapping: Use helpers to access irq_cfg data structure associated with IRQ
x86, irq: Use helpers to access irq_cfg data structure associated with IRQ
x86, irq: Make MSI and HT_IRQ indepenent of X86_IO_APIC
x86, irq: Move IRQ initialization routines from io_apic.c into vector.c
x86, irq: Move IOAPIC related declarations from hw_irq.h into io_apic.h
x86, irq: Move HT IRQ related code from io_apic.c into htirq.c
x86, irq: Move PCI MSI related code from io_apic.c into msi.c
x86, irq: Replace printk(KERN_LVL) with pr_lvl() utilities
x86, irq: Make UP version of irq_complete_move() an inline stub
x86, irq: Move local APIC related code from io_apic.c into vector.c
x86, irq: Introduce helpers to access struct irq_cfg
x86, irq: Protect __clear_irq_vector() with vector_lock
x86, irq: Rename local APIC related functions in io_apic.c as apic_xxx()
x86, irq: Refine hw_irq.h to prepare for irqdomain support
x86, irq: Convert irq_2_pin list to generic list
x86, irq: Kill useless parameter 'irq_attr' of IO_APIC_get_PCI_irq_vector()
x86, irq, acpi: Get rid of special handling of GSI for ACPI SCI
x86, irq: Introduce helper to check whether an IOAPIC has been registered
...
Now we have splitted functions to support MSI and HT_IRQ into vector.c,
and they have no dependency on IOAPIC any more. So change Kconfig files
to make MSI and HT_IRQ independent of X86_IO_APIC.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/1414397531-28254-16-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Clean up code by moving IOAPIC related declarations from hw_irq.h into
io_apic.h.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Aubrey <aubrey.li@linux.intel.com>
Cc: Ryan Desfosses <ryan@desfo.org>
Cc: Quentin Lambert <lambert.quentin@gmail.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: http://lkml.kernel.org/r/1414397531-28254-14-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
None of the callers requires irq_attr to be filled
in. IO_APIC_get_PCI_irq_vector() does not do anything useful with it
either.
Remove the parameter and fixup the call sites.
[ tglx: Massaged changelog ]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Ryan Desfosses <ryan@desfo.org>
Cc: Quentin Lambert <lambert.quentin@gmail.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: http://lkml.kernel.org/r/1414397531-28254-4-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
To support IOAPIC hotplug on x86 and IA64 platforms, OS needs to figure
out global interrupt source number(GSI) and IOAPIC enumeration ID
through ACPI interfaces. So BIOS must implement an ACPI IOAPIC device
with _GSB/_UID or _MAT method to support IOAPIC hotplug. OS also needs
to figure out base physical address to access IOAPIC registers. OS may
get the base physical address through PCI BARs if IOAPIC device is
visible in PCI domain, otherwise OS may get the address by ACPI _CRS
method if IOAPIC device is hidden from PCI domain by BIOS.
When adding a PCI subtree, we need to add IOAPIC devices before enabling
all other PCI devices because other PCI devices may use the IOAPIC to
allocate PCI interrupts.
So we plan to reimplement IOAPIC driver as an ACPI instead of PCI driver
due to:
1) hot-pluggable IOAPIC devices are always visible in ACPI domain,
but may or may not be visible in PCI domain.
2) we could explicitly control the order between IOAPIC and other PCI
devices.
We also have another choice to use a PCI driver to manage IOAPIC device
if it's visible in PCI domain and use an ACPI driver if it's only
visible in ACPI domain. But this solution is a little complex.
It shouldn't cause serious backward compatibility issues because:
1) IOAPIC hotplug is never supported on x86 yet because it hasn't
implemented the required acpi_register_ioapic() and
acpi_unregister_ioapic().
2) Currently only ACPI based IOAPIC hotplug is possible on x86 and
IA64, we don't know other specifications and interfaces to support
IOAPIC hotplug yet.
3) We will reimplement an ACPI IOAPIC driver to support IOAPIC hotplug.
This change also helps to get rid of the false alarm on all current
Linux distributions:
[ 6.952497] ioapic: probe of 0000:00:05.4 failed with error -22
[ 6.959542] ioapic: probe of 0000:80:05.4 failed with error -22
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/1414387308-27148-9-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Here's the big set of USB and PHY patches for 3.19-rc1.
The normal churn in the USB gadget area is in here, as well as xhci and
other individual USB driver updates. The PHY tree is also in here, as
there were dependancies on the USB tree.
All of these have been in linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOEHcACgkQMUfUDdst+ykziQCgsm1D/af2nac6CTF2pov8VMIY
ywgAnRi8LtZ2WassrwTNxY86Avaqryis
=UVp8
-----END PGP SIGNATURE-----
Merge tag 'usb-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big set of USB and PHY patches for 3.19-rc1.
The normal churn in the USB gadget area is in here, as well as xhci
and other individual USB driver updates. The PHY tree is also in
here, as there were dependancies on the USB tree.
All of these have been in linux-next"
* tag 'usb-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (351 commits)
arm: omap3: twl: remove usb phy init data
usbip: fix error handling in stub_probe()
usb: gadget: udc: missing curly braces
USB: mos7720: delete some unneeded code
wusb: replace memset by memzero_explicit
usbip: remove unneeded structure
usb: xhci: fix comment for PORT_DEV_REMOVE
xhci: don't use the same variable for stopped and halted rings current TD
xhci: clear extra bits from slot context when setting max exit latency
xhci: cleanup finish_td function
USB: adutux: NULL dereferences on disconnect
usb: chipidea: fix platform_no_drv_owner.cocci warnings
usb: chipidea: Fixed a few typos in comments
Documentation: bindings: add doc for the USB2 ChipIdea USB driver
usb: chipidea: add a usb2 driver for ci13xxx
usb: chipidea: fix phy handling
usb: chipidea: remove duplicate dev_set_drvdata for host_start
usb: chipidea: parameter 'mode' isn't needed for hw_device_reset
usb: chipidea: add controller reset API
usb: chipidea: remove flag CI_HDRC_REQUIRE_TRANSCEIVER
...
- Fully support non-coherent devices on ARM by introducing the
mechanisms to request the hypervisor to perform the required cache
maintainance operations.
- A number of pciback bug fixes and cleanups. Notably a deadlock fix
if a PCI device was manually uunbound and a fix for incorrectly
restoring state after a function reset.
- In x86 PVHVM guests, use the APIC for interrupts if this has been
virtualized by the hardware. This reduces the number of interrupt-
related VM exits on such hardware.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJUiYb+AAoJEFxbo/MsZsTRwmEH+gNaJz5r8gIJlq8Q51+nOIs4
Gw6HdjUB5MOT47vDV4treEOx0Bk8hYTfgWUWvAC81JMJ1sMWOVrUGuG/0lmzaomW
zXvSk+o0n4LafwEhHb8LIccZMbaH7f9o3PNdNchrTkPrIl8Gf2nmBXCkDsT4mRye
5ZFpc4ntgBrznh3baPYDS8PCAmlyZ0uVEnz1ofYI6S80dC13siEiPG0c9TrNEKzO
glhvgCRmR0C4ZNLblM36HWBEqrdLuGCoNJSH+7okygyP2TLD3aO4R+9aD5JWYNdf
fO2WmivX/zK+UGVAElrLx+rb8R2dv3ddeaE5piZhIBUieopIWJd32L3LhQORdtc=
=N6DP
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.19-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen features and fixes from David Vrabel:
- Fully support non-coherent devices on ARM by introducing the
mechanisms to request the hypervisor to perform the required cache
maintainance operations.
- A number of pciback bug fixes and cleanups. Notably a deadlock fix
if a PCI device was manually uunbound and a fix for incorrectly
restoring state after a function reset.
- In x86 PVHVM guests, use the APIC for interrupts if this has been
virtualized by the hardware. This reduces the number of interrupt-
related VM exits on such hardware.
* tag 'stable/for-linus-3.19-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (26 commits)
Revert "swiotlb-xen: pass dev_addr to swiotlb_tbl_unmap_single"
xen/pci: Use APIC directly when APIC virtualization hardware is available
xen/pci: Defer initialization of MSI ops on HVM guests
xen-pciback: drop SR-IOV VFs when PF driver unloads
xen/pciback: Restore configuration space when detaching from a guest.
PCI: Expose pci_load_saved_state for public consumption.
xen/pciback: Remove tons of dereferences
xen/pciback: Print out the domain owning the device.
xen/pciback: Include the domain id if removing the device whilst still in use
driver core: Provide an wrapper around the mutex to do lockdep warnings
xen/pciback: Don't deadlock when unbinding.
swiotlb-xen: pass dev_addr to swiotlb_tbl_unmap_single
swiotlb-xen: call xen_dma_sync_single_for_device when appropriate
swiotlb-xen: remove BUG_ON in xen_bus_to_phys
swiotlb-xen: pass dev_addr to xen_dma_unmap_page and xen_dma_sync_single_for_cpu
xen/arm: introduce GNTTABOP_cache_flush
xen/arm/arm64: introduce xen_arch_need_swiotlb
xen/arm/arm64: merge xen/mm32.c into xen/mm.c
xen/arm: use hypercall to flush caches in map_page
xen: add a dma_addr_t dev_addr argument to xen_dma_map_page
...
This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come
from as long as the platform firmware (either DT or ACPI) makes
them available. It covers both devices and "bare" device node
objects without struct device representation as that turns out to
be necessary in some cases. This has been in the works for quite
a few months (and development cycles) and has been approved by
all of the relevant maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO information
in their ACPI tables, but don't assign names to GPIO lines (in which
case the driver needs to do that on the basis of what it knows about
the device in question). That also has been approved by the GPIO
core maintainers and the rfkill driver is now going to use it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by
the processor in which case it will be enabled by default. However,
it can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller).
The support added this time is sufficient to make the ACPI battery
driver work on Asus T100A, but it is general enough to be able to
cover some other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver
for Intel platforms should be able to handle power management of
the DMA engine correctly, the cpufreq-dt driver should interact
with the thermal subsystem in a better way and the ACPI backlight
driver should handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions
in the ACPICA's interrupt handling code which might lead to some
random and strange looking failures on some systems.
In the cleanups department the most visible part is the series
of commits targeted at getting rid of the CONFIG_PM_RUNTIME
configuration option. That was triggered by a discussion
regarding the generic power domains code during which we realized
that trying to support certain combinations of PM config options
was painful and not really worth it, because nobody would use them
in production anyway. For this reason, we decided to make
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and that lead to the
conclusion that the latter became redundant and CONFIG_PM could
be used instead of it. The material here makes that replacement
in a major part of the tree, but there will be at least one more
batch of that in the second part of the merge window.
Specifics:
- Support for retrieving device properties information from ACPI
_DSD device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that.
As stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers
are now going to use this new interface and the GPIO subsystem
is additionally modified to allow device drivers to assign names
to GPIO resources returned by ACPI _CRS objects (in case _DSD is
not present or does not provide the expected data). The changes
in this set are mostly from Mika Westerberg, Rafael J Wysocki,
Aaron Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions
used by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management
(Aaron Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects
and deferred probing support for the ACPI battery driver based
on the _DEP information to make that driver work on Asus T100A
(Lan Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling
code and in the ACPI code related to system suspend and resume
(Lv Zheng and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had
been allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in
that code with synchronize_rcu_expedited() which makes the issue
go away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly.
The problem is that the DMA engine doesn't have ACPI PM support
of its own and it simply is turned off when the last LPSS device
having ACPI PM support goes into D3cold. To work around that,
the PM domain used by the ACPI LPSS driver is redesigned so at
least one device with ACPI PM support will be on as long as the
DMA engine is in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and
Ashwin Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver
fixes and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at
probe time (Ulf Hansson).
- Preliminary support for controlling device clocks from the
generic power domains core code and modifications of the
ARM/shmobile platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power
domains core code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control
code in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and
a new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu,
James Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to
allow OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and
Markus Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5dox
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come from
as long as the platform firmware (either DT or ACPI) makes them
available. It covers both devices and "bare" device node objects
without struct device representation as that turns out to be necessary
in some cases. This has been in the works for quite a few months (and
development cycles) and has been approved by all of the relevant
maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO
information in their ACPI tables, but don't assign names to GPIO lines
(in which case the driver needs to do that on the basis of what it
knows about the device in question). That also has been approved by
the GPIO core maintainers and the rfkill driver is now going to use
it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by the
processor in which case it will be enabled by default. However, it
can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller). The
support added this time is sufficient to make the ACPI battery driver
work on Asus T100A, but it is general enough to be able to cover some
other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
Intel platforms should be able to handle power management of the DMA
engine correctly, the cpufreq-dt driver should interact with the
thermal subsystem in a better way and the ACPI backlight driver should
handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions in the
ACPICA's interrupt handling code which might lead to some random and
strange looking failures on some systems.
In the cleanups department the most visible part is the series of
commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
option. That was triggered by a discussion regarding the generic
power domains code during which we realized that trying to support
certain combinations of PM config options was painful and not really
worth it, because nobody would use them in production anyway. For
this reason, we decided to make CONFIG_PM_SLEEP select
CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
became redundant and CONFIG_PM could be used instead of it. The
material here makes that replacement in a major part of the tree, but
there will be at least one more batch of that in the second part of
the merge window.
Specifics:
- Support for retrieving device properties information from ACPI _DSD
device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that. As
stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are
now going to use this new interface and the GPIO subsystem is
additionally modified to allow device drivers to assign names to
GPIO resources returned by ACPI _CRS objects (in case _DSD is not
present or does not provide the expected data). The changes in
this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions used
by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management (Aaron
Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects and
deferred probing support for the ACPI battery driver based on the
_DEP information to make that driver work on Asus T100A (Lan
Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling code
and in the ACPI code related to system suspend and resume (Lv Zheng
and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had been
allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in that
code with synchronize_rcu_expedited() which makes the issue go
away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly. The
problem is that the DMA engine doesn't have ACPI PM support of its
own and it simply is turned off when the last LPSS device having
ACPI PM support goes into D3cold. To work around that, the PM
domain used by the ACPI LPSS driver is redesigned so at least one
device with ACPI PM support will be on as long as the DMA engine is
in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver fixes
and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at probe
time (Ulf Hansson).
- Preliminary support for controlling device clocks from the generic
power domains core code and modifications of the ARM/shmobile
platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power domains core
code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control code
in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to allow
OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and Markus
Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava)"
* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
leds: leds-gpio: Fix multiple instances registration without 'label' property
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
...
Pull irq domain updates from Thomas Gleixner:
"The real interesting irq updates:
- Support for hierarchical irq domains:
For complex interrupt routing scenarios where more than one
interrupt related chip is involved we had no proper representation
in the generic interrupt infrastructure so far. That made people
implement rather ugly constructs in their nested irq chip
implementations. The main offenders are x86 and arm/gic.
To distangle that mess we have now hierarchical irqdomains which
seperate the various interrupt chips and connect them via the
hierarchical domains. That keeps the domain specific details
internal to the particular hierarchy level and removes the
criss/cross referencing of chip internals. The resulting hierarchy
for a complex x86 system will look like this:
vector mapped: 74
msi-0 mapped: 2
dmar-ir-1 mapped: 69
ioapic-1 mapped: 4
ioapic-0 mapped: 20
pci-msi-2 mapped: 45
dmar-ir-0 mapped: 3
ioapic-2 mapped: 1
pci-msi-1 mapped: 2
htirq mapped: 0
Neither ioapic nor pci-msi know about the dmar interrupt remapping
between themself and the vector domain. If interrupt remapping is
disabled ioapic and pci-msi become direct childs of the vector
domain.
In hindsight we should have done that years ago, but in hindsight
we always know better :)
- Support for generic MSI interrupt domain handling
We have more and more non PCI related MSI interrupts, so providing
a generic infrastructure for this is better than having all
affected architectures implementing their own private hacks.
- Support for PCI-MSI interrupt domain handling, based on the generic
MSI support.
This part carries the pci/msi branch from Bjorn Helgaas pci tree to
avoid a massive conflict. The PCI/MSI parts are acked by Bjorn.
I have two more branches on top of this. The full conversion of x86
to hierarchical domains and a partial conversion of arm/gic"
* 'irq-irqdomain-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (41 commits)
genirq: Move irq_chip_write_msi_msg() helper to core
PCI/MSI: Allow an msi_controller to be associated to an irq domain
PCI/MSI: Provide mechanism to alloc/free MSI/MSIX interrupt from irqdomain
PCI/MSI: Enhance core to support hierarchy irqdomain
PCI/MSI: Move cached entry functions to irq core
genirq: Provide default callbacks for msi_domain_ops
genirq: Introduce msi_domain_alloc/free_irqs()
asm-generic: Add msi.h
genirq: Add generic msi irq domain support
genirq: Introduce callback irq_chip.irq_write_msi_msg
genirq: Work around __irq_set_handler vs stacked domains ordering issues
irqdomain: Introduce helper function irq_domain_add_hierarchy()
irqdomain: Implement a method to automatically call parent domains alloc/free
genirq: Introduce helper irq_domain_set_info() to reduce duplicated code
genirq: Split out flow handler typedefs into seperate header file
genirq: Add IRQ_SET_MASK_OK_DONE to support stacked irqchip
genirq: Introduce irq_chip.irq_compose_msi_msg() to support stacked irqchip
genirq: Add more helper functions to support stacked irq_chip
genirq: Introduce helper functions to support stacked irq_chip
irqdomain: Do irq_find_mapping and set_type for hierarchy irqdomain in case OF
...
We have the pci_load_and_free_saved_state, and pci_store_saved_state
but are missing the functionality to just load the state
multiple times in the PCI device without having to free/save
the state.
This patch makes it possible to use this function.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so quite a few
depend on CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM in the PCI core code.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
NVIDIA Tegra
- Use physical range for I/O mapping (Thierry Reding)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJUf1W0AAoJEFmIoMA60/r8wIUP/iFJKucfHJUDo3i/R96vXYhv
/PEosMwQu2FnfLC13vOnUnx9m2uv2gpthhI255guxm3DUIsurOcdBGR7ZoaQcMkD
0NMf/UeGlKPFkXk5ltJiO4SHsAv8ITMV7pYcUl4DX0E288kBjM4LV69+aprKw7GY
ULZDDqIE5x6SkmBv5PopTr7M+Z6omQ+nxZ6txMAM3ks2+rku6SzqPaWZFhpTinqn
AJlx9gqjN8OLuPNXqHia+hBzPk9xvisCOZ0kOXpS3ipeXvyLVPThqhO1fG9RFY0a
BXK+l8E7z3zcwIZIQMsVl3zuxYVpjQhgNlPqFyYE+TCW/kG6V3STWzmYW/kCT0ax
ipVeSKXZnmcf7iKZ78UdW8bXZGHi6WNouaN0/NAtXh9Gln8P2qOuSBwv1H3374in
NnIFPr8bFNXgSr8OPZWIqhwQEdPZgydxq28DxIEZCdYo4idP3Q+yElQPpmZzBeeC
8rnFyHsBFdazr7W44jsPnn45Fdy2LEEo07v80buj/RwdwMV2zj2OFLUMT9Nlyu6k
p7HLM40FZlyeu+OHjzc0zu/GjQ5CAt4SV0DSQ/Gi80Bq1X+qHPVc7u6MoKmS0wYr
wZ2/DCXHloMRsITZ6fyPVNsUHB9S9M01V4VCnzCSeJ65ArvNeP5+7yzQKUIEKLQ9
FclPrRsT+jaJUWVpNLjE
=KWwE
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.18-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fix from Bjorn Helgaas:
"This fixes a Tegra20 regression that we introduced during the v3.18
merge window"
* tag 'pci-v3.18-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: tegra: Use physical range for I/O mapping
Commit 0b0b0893d4 ("of/pci: Fix the conversion of IO ranges into IO
resources") changed how I/O resources are parsed from DT. Rather than
containing the physical address of the I/O region, the addresses will now
be in I/O address space.
On Tegra the union of all ranges is used to expose a top-level memory-
mapped resource for the PCI host bridge. This helps to make /proc/iomem
more readable.
Combining both of the above, the union would now include the I/O space
region. This causes a regression on Tegra20, where the physical base
address of the PCIe controller (and therefore of the union) is located at
physical address 0x80000000. Since I/O space starts at 0, the union will
now include all of system RAM which starts at 0x00000000.
This commit fixes this by keeping two copies of the I/O range: one that
represents the range in the CPU's physical address space, the other for the
range in the I/O address space. This allows the translation setup within
the driver to reuse the physical addresses. The code registering the I/O
region with the PCI core uses both ranges to establish the mapping.
Fixes: 0b0b0893d4 ("of/pci: Fix the conversion of IO ranges into IO resources")
Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
This can be set by quirks/drivers to be used by the architecture code
that assigns the MSI addresses.
We additionally add verification in the core MSI code that the values
assigned by the architecture do satisfy the limitation in order to fail
gracefully if they don't (ie. the arch hasn't been updated to deal with
that quirk yet).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
With the new stacked irq domains, it becomes pretty tempting to
allocate an MSI domain per PCI bus, which would remove the requirement
of either relying on arch-specific code, or a default PCI MSI domain.
By allowing the msi_controller structure to carry a pointer to an
irq_domain, we can easily use this in pci_msi_setup_msi_irqs. The
existing code can still be used as a fallback if the MSI driver does
not populate the domain field.
Tested on arm64 with the GICv3 ITS driver.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Link: http://lkml.kernel.org/r/1416048553-29289-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Provide mechanism to directly alloc/free MSI/MSIX interrupt from
irqdomain, which will be used to replace arch_setup_msi_irq()/
arch_setup_msi_irqs()/arch_teardown_msi_irq()/arch_teardown_msi_irqs().
To kill weak functions, this patch introduce a new weak function
arch_get_pci_msi_domain(), which is to retrieve the MSI irqdomain
for a PCI device. This weak function could be killed once we get
a common way to associate MSI domain with PCI device.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Alexander Gordeev <agordeev@redhat.com>
Link: http://lkml.kernel.org/r/1416061447-9472-10-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Enhance PCI MSI core to support hierarchy irqdomain, so the common
code can be shared across architectures.
[ tglx: Extracted and combined from several patches ]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Required to support non PCI based MSI.
[ tglx: Extracted from Jiangs patch series ]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The PCI/MSI irq chip callbacks mask/unmask_msi_irq have been renamed
to pci_msi_mask/unmask_irq to mark them PCI specific. Rename all usage
sites. The conversion helper functions are kept around to avoid
conflicts in next and will be removed after merging into mainline.
Coccinelle assisted conversion. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: x86@kernel.org
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Mohit Kumar <mohit.kumar@st.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Yijing Wang <wangyijing@huawei.com>
mask/unmask_msi_irq and __mask_msi/msix_irq are PCI/MSI specific
functions and should be named accordingly. This is a preparatory patch
to support MSI on non PCI devices.
Rename mask/unmask_msi_irq to pci_msi_mask/unmask_irq and document the
functions. Provide conversion helpers.
Rename __mask_msi/msix_irq to __pci_msi/msix_desc_mask so its clear
that they operated on msi_desc. Fixup the only user outside of
pci/msi.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Rename write_msi_msg() to pci_write_msi_msg() to mark it as PCI
specific.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Rename __read_msi_msg() to __pci_read_msi_msg() and kill unused
read_msi_msg(). It's a preparation to separate generic MSI code from
PCI core.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
It is the repsonsibility of arch_setup_msi_irq()/arch_setup_msi_irqs()
to call irq_set_msi_desc() to associate IRQ descriptors and MSI
descriptors. Kill the redundant call of irq_set_msi_desc() for MSI-X
interrupts in the PCI MSI core.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Per Documentation/CodingStyle, don't use braces around single statements.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Resource management
- Support 64-bit bridge windows if we have 64-bit dma_addr_t (Yinghai Lu)
PCI device hotplug
- Apply _HPX Link Control settings to all devices with a link (Yinghai Lu)
Generic host bridge driver
- Add DT binding for "linux,pci-domain" property (Lucas Stach)
APM X-Gene
- Assign resources to bus before adding new devices (Duc Dang)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJUbkCkAAoJEFmIoMA60/r8HHcQAMBeaF4pbUYotzpd8kwjFQ2x
d9DPU3bAfeMY3U4qKRkp/GXV1F1ueVP2KgwaKlV9ytrILFwVYlsy2DZ/JIS3ggw2
BfjPTVB6rADzhfZB0HNSQQGOcGbKezd4sM45E6hsZqxzlgnVJQ5oL0u/PL5fuvC1
+1goznoJwOhLMn9bsSS+b/2bgmPG1HYonFu1ehiSTt/g9e0Q2YsMkCZDo8R3i6nl
W25g93m1yP7KO3AnPsnE9dm9oDEcbqVbfSu+Z8X2NllN8/+e6+z7CtDZx5OfMpRI
GBQrLuPXi0NxFeFcj+gbAfhV8ZsFDdqNXPHuqC7pOKlveCmyk8tBhXcIr9gTnGQF
/UjxgWDekH6Cb8DjFVQCj84D5f1U7RNRbpkeEr6gXtoM7vPDfQaCROC5qhBKGV+P
XAQ4ujGkCe3A9ve2XNsgHzLQgRoRopfI6aN2VZxQYaxvobm+QzuMW7BtKJ72dUKJ
LIPnlc+X1ccwg+ZyWFvgLByMKCriklTjeFA2UMP6WI7xD3r5N+Y0QP0no4zVPIMN
no5RAx7sv71yE97Y/SSosirfjQ3YlJ55KJRJY2+j2obD9wLCCEwJuiNnrYU+EB6c
Z/cPmZhGKZnBcDJMazjULe2gldVDRokIRk069ySob4iUdZ4n/vIdCbNR5Z0f6dAr
w7SfdPXK2ARn0ulqzdT1
=smv9
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.18-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These are fixes for an issue with 64-bit PCI bus addresses on 32-bit
PAE kernels, an APM X-Gene problem (it depended on a generic change we
removed before merging), a fix for my hotplug device configuration
changes, and a devicetree documentation update.
Resource management:
- Support 64-bit bridge windows if we have 64-bit dma_addr_t (Yinghai Lu)
PCI device hotplug:
- Apply _HPX Link Control settings to all devices with a link (Yinghai Lu)
Generic host bridge driver:
- Add DT binding for "linux,pci-domain" property (Lucas Stach)
APM X-Gene:
- Assign resources to bus before adding new devices (Duc Dang)"
* tag 'pci-v3.18-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Support 64-bit bridge windows if we have 64-bit dma_addr_t
PCI: Apply _HPX Link Control settings to all devices with a link
PCI: Add missing DT binding for "linux,pci-domain" property
PCI: xgene: Assign resources to bus before adding new devices
* pci/msi:
s390/MSI: Use __msi_mask_irq() instead of default_msi_mask_irq()
Revert "PCI: Add x86_msi.msi_mask_irq() and msix_mask_irq()"
PCI/MSI: Add pci_msi_ignore_mask to prevent writes to MSI/MSI-X Mask Bits
Save MSI controller in pci_sys_data instead of assigning MSI controller
pointer to every PCI bus in .add_bus().
[bhelgaas: use xilinx_pcie_msi_chip, not xilinx_pcie_msi_controller]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Save MSI controller in pci_sys_data instead of assigning MSI controller
pointer to every PCI bus in .add_bus().
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Save MSI controller in pci_sys_data instead of assigning MSI controller
pointer to every PCI bus in .add_bus().
[bhelgaas: use struct rcar_msi.chip, not ctrl]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Save MSI controller in pci_sys_data instead of assigning MSI controller
pointer to every PCI bus in .add_bus().
[bhelgaas: use dw_pcie_msi_chip, not dw_pcie_msi_controller]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Save MSI controller in pci_sys_data instead of assigning MSI controller
pointer to every PCI bus in .add_bus().
[bhelgaas: use struct tegra_msi.chip, not ctrl]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_iov_resource_bar() always sets its 'pci_bar_type' parameter to
'pci_bar_unknown'. Drop the parameter and just use 'pci_bar_unknown'
directly in the callers.
No functional change intended.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Chris Wright <chrisw@sous-sol.org>
CC: Yu Zhao <yuzhao@google.com>
As a consequence of restoring the detection of invalid BARs, add a new
informational printk like the following when such occurrences are
encountered.
pci ssss:bb:dd.f: [Firmware Bug]: reg 0xXX: invalid BAR (can't size)
Reported-by: William Unruh <unruh@physics.ubc.ca>
Reported-by: Martin Lucina <martin@lucina.net>
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Matthew Wilcox <willy@linux.intel.com>
Aaron reported that a 32-bit x86 kernel with Physical Address Extension
(PAE) support complains about bridge prefetchable memory windows above 4GB:
pci_bus 0000:00: root bus resource [mem 0x380000000000-0x383fffffffff]
...
pci 0000:03:00.0: reg 0x10: [mem 0x383fffc00000-0x383fffdfffff 64bit pref]
pci 0000:03:00.0: reg 0x20: [mem 0x383fffe04000-0x383fffe07fff 64bit pref]
pci 0000:03:00.1: reg 0x10: [mem 0x383fffa00000-0x383fffbfffff 64bit pref]
pci 0000:03:00.1: reg 0x20: [mem 0x383fffe00000-0x383fffe03fff 64bit pref]
pci 0000:00:02.2: PCI bridge to [bus 03-04]
pci 0000:00:02.2: bridge window [io 0x1000-0x1fff]
pci 0000:00:02.2: bridge window [mem 0x91900000-0x91cfffff]
pci 0000:00:02.2: can't handle 64-bit address space for bridge
In this kernel, unsigned long is 32 bits and dma_addr_t is 64 bits.
Previously we used "unsigned long" to hold the bridge window address. But
this is a bus address, so we should use dma_addr_t instead.
Use dma_addr_t to hold the bridge window base and limit.
The question of whether the CPU can actually *address* the window is
separate and depends on what the physical address space of the CPU is and
whether the host bridge does any address translation.
[bhelgaas: fix "shift count > width of type", changelog, stable tag]
Fixes: d56dbf5bab ("PCI: Allocate 64-bit BARs above 4G when possible")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=88131
Reported-by: Aaron Ma <mapengyu@gmail.com>
Tested-by: Aaron Ma <mapengyu@gmail.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.14+
* pci/host-designware:
PCI: designware: Add a blank line after declarations
* pci/host-dra7xx:
PCI: dra7xx: Add __init annotation to dra7xx_add_pcie_port()
PCI: dra7xx: Rename add_pcie_port() to dra7xx_add_pcie_port()
* pci/host-exynos:
PCI: exynos: Remove unnecessary return statement
PCI: exynos: Add exynos prefix to add_pcie_port()/pcie_init()
* pci/host-generic:
PCI: generic: Convert to DT resource parsing API
PCI: generic: Allocate config space windows after limiting bus number range
* pci/host-imx6:
PCI: imx6: Use tabs for indentation
* pci/host-keystone:
PCI: keystone: Remove unnecessary OOM message
PCI: keystone: Make ks_dw_pcie_msi_domain_ops static
* pci/host-layerscape:
PCI: layerscape: Add Freescale Layerscape PCIe driver
* pci/host-mvebu:
PCI: mvebu: Add a blank line after declarations
* pci/host-rcar:
PCI: rcar: Make rcar_pci static
* pci/host-spear:
PCI: spear: Remove unnecessary OOM message
PCI: spear: Add __init annotation to spear13xx_add_pcie_port()
PCI: spear: Rename add_pcie_port(), pcie_init() to spear13xx_add_pcie_port(), etc.
* pci/host-tegra:
PCI: tegra: Add Kconfig help text
PCI: tegra: Do not build on 64-bit ARM
Previously we applied _HPX type 2 record Link Control register settings
only to bridges with a subordinate bus. But it's better to apply them to
all devices with a link because if the subordinate bus has not been
allocated yet, we won't apply settings to the device.
Use pcie_cap_has_lnkctl() to determine whether the device has a Link
Control register instead of looking at dev->subordinate.
[bhelgaas: changelog]
Fixes: 6cd33649fa ("PCI: Add pci_configure_device() during enumeration")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a standard help text to the Kconfig entry for the Tegra PCIe host
controller driver.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
32-bit and 64-bit ARM use very different infrastructure to register a PCI
host bridge. The Tegra PCIe host controller driver currently only supports
the 32-bit ARM infrastructure, so prevent it from being built on 64-bit ARM
where it will break.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The site-specific OOM messages are unnecessary, because they duplicate the
MM subsystem generic OOM message. This patch fixes the following
checkpatch warning:
WARNING: Possible unnecessary 'out of memory' message
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
This patch fixes the following checkpatch warning:
WARNING: Missing a blank line after declarations
[bhelgaas: drop mvebu_pcie_add_bus() change because it's going away anyway]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
This patch fixes the following checkpatch warning:
WARNING: Missing a blank line after declarations
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This patch fixes the following checkpatch warning:
WARNING: void function return statements are not generally useful
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This patch fixes the following checkpatch error:
ERROR: code indent should use tabs where possible
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The site-specific OOM messages are unnecessary because they duplicate the
MM subsystem generic OOM message. This patch fixes the following
checkpatch warning:
WARNING: Possible unnecessary 'out of memory' message
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
