When drm_helper_disable_unused_functions calls disable
function of the CRTC, it also sets the crtc->fb pointer
to NULL. This can later (when the mode on that CRTC is setup
again from user space) cause ***_do_set_base functions to
"think" that there is no old buffer and skip the unpinning
code. Consequently, the buffer that has been NULL-ified in
drm_helper_disable_unused_functions will never be unpinned
causing a leak in VRAM.
This patch plugs the leak by unpinning the frame buffer
in crtc_disable function.
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Since we aren't using it when the crtc is disabled, turn it off
to save power. The GRPH block is the part of the display
controller that controls the primary graphics plane (size,
address, etc.).
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
v2: make PPLL0 is available for non-DP on CI
v3: rebase changes, update documentation
v4: fix kabini
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
bool in_mode_set from struct radeon_crtc is not used anymore.
Signed-off-by: Niels Ole Salscheider <niels_ole@salscheider-online.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Only enable it when we disable the display rather than
at DPMS time since enabling it requires a full modeset
to restore the display state. Fixes blank screens in
certain cases.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This fix black screen on resume issue that some people are
experiencing. There is a bug in the atombios code regarding
pll/crtc mapping. The atombios code reverse the logic for
the pll and crtc mapping.
agd5f: drop unnecessary crtc id check, cc stable in case
we miss 3.7.
This fixes the root cause that was worked around by commits:
drm/radeon: allocate PPLLs from low to high
drm/radeon/dce3: switch back to old pll allocation order for discrete
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The order shouldn't matter, but this seems to cause regressions for
certain specific cases. This should fix it for now. We probably
need to investigate a proper fix in the next development cycle.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Andy Furniss <andyqos@ukfsn.org>
The order shouldn't matter, but there have been problems
reported on certain older asics. This behaves more
like the original code before the PPLL allocation
rework.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Markus Trippelsdorf <markus@trippelsdorf.de>
This allows us to bail if we can't support the requested
setup from a PPLL perspective. Prevents broken setups
from being attempted.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Since the current KMS API sets the mode independantly on
each crtc, we may end up with resource conflicts. The PLL
allocation is one of those cases. In the following example
we have 3 crtcs in use driving 2 DVI connectors and 1 DP
connector. On the initial kernel modeset for fbdev, the
display topology ends up as follows:
crtc0 -> DP-0
crtc1 -> DVI-0
crtc2 -> DVI-1
Because this is the first modeset, all of the PLLs are
available as none have been assigned. So we end up with
the following:
crtc0 uses DCPLL
crtc1 uses PPLL2
crtc2 uses PPLL1
When X starts, it assigns a different topology:
crtc0 -> DVI-0
crtc1 -> DP-0
crtc2 -> DVI-1
However, since the KMS API is per crtc, we set the mode on each
crtc independantly. When it comes time to set the mode on crtc0,
the topology for crtc1 and crtc2 are still intact. crtc1 and
crtc2 are already assigned PPLL2 and PPLL1 so when it comes time
to set the mode on crtc0, crtc1 and crtc2 have not been torn down
yet, so there appears to be no PLLs available. In reality, we
are reconfiguring the entire display topology, however, since
each crtc is handled independantly, we don't know that in the
driver at each crtc mode set time.
This patch checks to see if the same connector is being driven by
another crtc, and if so, uses the PLL already associated with it.
v2: store connector in the radeon crtc struct, simplify checking.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Compare the adjusted clock as well as the crtc mode
clock. This handles cases where the driver adjusts
the clock for specific special cases.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need the calculate the pixel clock before allocating a PPLL
in order to insure the clocks really match.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If several non-DP displays use the same pixel clock
we can use the same PPLL for all of them. If all
relevant displays have the same pixel clock, this
allows the driver to:
- use fewer PPLLs which saves power
- support more than two non-DP displays on DCE4+
The current drm modesetting infrastructure doesn't
really provide a good framework for validating combinations
that work or won't work, so it's possible you could go from
a working configuration to a non-working one by changing the
mode a one of the displays. However, there this is better
than what was there before.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For DP we can use the same PPLL for all active DP
encoders. Take advantage of that to prevent cases
where we may end up sharing a PPLL between DP and
non-DP which won't work. Also clean up the code
a bit.
v2: - fix missing pll_id assignment in crtc init
v3: - fix DP PPLL check
- document functions
- break in main encoder search loop after matching.
no need to keep checking additional encoders.
v4: - same as v3, but re-apply to drm-next as the corner
cases are fixed properly in subsequent patches.
fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=54471
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
MiscInfo field should be programmed with the crtc id
rather than the pll id. However, at this point the
two are the same for chips with this version of the table.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 985f61f7ee.
This commit fixed certain cases, but ended up regressing others
due to limitations in the current KMS API. A proper fix is too
invasive for 3.6. Push it back to 3.7.
Reported-by: Andres Freund <andres@anarazel.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For DP we can use the same PPLL for all active DP
encoders. Take advantage of that to prevent cases
where we may end up sharing a PPLL between DP and
non-DP which won't work. Also clean up the code
a bit.
v2: - fix missing pll_id assignment in crtc init
v3: - fix DP PPLL check
- document functions
- break in main encoder search loop after matching.
no need to keep checking additional encoders.
fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=54471
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Power gating is per crtc pair, but the powergating registers
should be called individually. The hw handles power up/down
properly. The pair is powered up if either crtc in the pair
is powered up and the pair is not powered down until both
crtcs in the pair are powered down. This simplifies
programming and should save additional power as the previous
code never actually power gated the crtc pair.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Some plls are shared for DP.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
If spread spectrum is enabled and in use for a given pll we
should not turn it off as it will lead to turning off display
for crtc that use the pll (this behavior was observed on chelsea
edp).
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
No functional change, but re-order the cases so they
evaluate properly due to the way the DCE macros work.
Noticed by kallisti5 on IRC.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to make sure the crtc is gated on before modesetting.
Explicitly gate the crtc on in prepare() and set a flag
so that the dpms functions don't gate it off during
mode set.
Noticed by sylware on IRC.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The passed mode must not be modified by the operation, make it const.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Need to actually set the SS parameters rather than just 0.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Selecting ATOM_PPLL_INVALID should be equivalent as the
DCPLL or PPLL0 are already programmed for the DISPCLK, but
the preferred method is to always specify the PLL selected.
SetPixelClock will check the parameters and skip the
programming if the PLL is already set up.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
- Use the correct union for getting the tiling info
- Properly init the PIPE_CONFIG field for SI
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPpvY9AAoJEHm+PkMAQRiGpEoIAJgbu+Y8gITnBK/wh9O6zy3S
5jie5KK4YWdbJsvO58WbNr3CyVIwGIqQ2dUZLiU59aBVLarlGw8xor0MmW+cZwhp
6fBHaf0qDYAV0MZjD+mnnExOiCRyISa2lPmsfu9dAWywh5KGe6/oAP6/qcXIyok3
KZyl3qQf4ENpaZPHwZPXCEkUvtuyHgNiszN+QXEadA3s19Ot4VGe9A3VGw+GNrSm
JqFIq3acQAbKa5BYaqf7TQC02v2FI7//eqt6QHxTqbE6a7LGbTvLfX3HlJ2mnfqa
1R6QHhM4y4OZDHbaMT2raHZ8WuLXzhehJzhP8Co7AHFOKwVKOb5XbcUr2RrukMU=
=HkMd
-----END PGP SIGNATURE-----
Merge tag 'v3.4-rc6' into drm-intel-next
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Ok, this is a fun story of git totally messing things up. There
/shouldn't/ be any conflict in here, because the fixes in -rc6 do only
touch functions that have not been changed in -next.
The offending commits in drm-next are 14415745b2..1fa611065 which
simply move a few functions from intel_display.c to intel_pm.c. The
problem seems to be that git diff gets completely confused:
$ git diff 14415745b2..1fa611065
is a nice mess in intel_display.c, and the diff leaks into totally
unrelated functions, whereas
$git diff --minimal 14415745b2..1fa611065
is exactly what we want.
Unfortunately there seems to be no way to teach similar smarts to the
merge diff and conflict generation code, because with the minimal diff
there really shouldn't be any conflicts. For added hilarity, every
time something in that area changes the + and - lines in the diff move
around like crazy, again resulting in new conflicts. So I fear this
mess will stay with us for a little longer (and might result in
another backmerge down the road).
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Improve handling of bpc (bits per color) in radeon.
In most cases we want 8 except for HDMI, DP, LVDS, and eDP.
v2: handle DP better.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Using the bpc (bits per color) specified by the monitor
can cause problems in some cases. Until we get a better
handle on how to deal with those cases, just use a bpc of 8.
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
It's handled via external clock. It should already be protected
by the external ss flag, but add an explicit check just in case.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On TN, UNIPHYA always uses PPLL2, UNIPHYB/C/D/E/F
can use either PPLL1 or PPLL0.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Rename the function to better match the functionality.
DCPLL became PLL0 on DCE6.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Each pair of crtcs (0/1, 2/3, 4/5) can be power gated.
Make sure the power is applied when the crtc is in use and
only power down the pair when both are off.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The hw no longer has the bits and the table is removed.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
