Initialize the gpio chip's of_node to the device's node
to work with DT based system.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The chained handler was set for the platform device with id == 0.
When the gpio devices are instantiated by a device tree, all have id ==
-1 and so the handler was unset resulting in unusable gpio irqs on
i.MX21 and i.MX27 (when using oftree).
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Without this, modules can't use this API, leading to build failures.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Not paying attention to the value being set is a bad thing because it
means that we'll not set the hardware up to reflect what was requested.
Not setting the hardware up to reflect what was requested means that the
caller won't get the results they wanted.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The feature GPIO_MSM_V1 is only available on three SoCs. On all other MSM SoCs
the INT_GPIO_GROUP{1,2} is undeclared, but Kconfig does allow such
configurations. Therefore the produced configuration is valid, but does not
compile. The problem is fixed by adding the missing Kconfig constraints.
drivers/gpio/gpio-msm-v1.c: In function âmsm_init_gpioâ:
drivers/gpio/gpio-msm-v1.c:629:26: error: 'INT_GPIO_GROUP1' undeclared
drivers/gpio/gpio-msm-v1.c:630:26: error: 'INT_GPIO_GROUP2' undeclared
Signed-off-by: Christian Dietrich <christian.dietrich@informatik.uni-erlangen.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If there is no platform data available, the driver shouldn't use the
pointer or it will oops. Since things will mostly work nonetheless,
(the BIOS may have set up the pins properly), I'd better not fail the
probe even in this case.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since commit 1c6c69525b ("genirq: Reject bogus threaded irq requests")
threaded IRQs without a primary handler need to be requested with
IRQF_ONESHOT, otherwise the request will fail. This patch adds the
IRQF_ONESHOT to input drivers where it is missing. Not modified by
this patch are those drivers where the requested IRQ will always be a
nested IRQ (e.g. because it's part of an MFD), since for this special
case IRQF_ONESHOT is not required to be specified when requesting the
IRQ.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When inbound messages arrive, rpmsg core looks up their associated
endpoint (by destination address) and then invokes their callback.
We've made sure that endpoints will never be de-allocated after they
were found by rpmsg core, but we also need to protect against the
(rare) scenario where the rpmsg driver was just removed, and its
callback function isn't available anymore.
This is achieved by introducing a callback mutex, which must be taken
before the callback is invoked, and, obviously, before it is removed.
Cc: stable <stable@vger.kernel.org>
Reported-by: Fernando Guzman Lugo <fernando.lugo@ti.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
When an inbound message arrives, the rpmsg core looks up its
associated endpoint and invokes the registered callback.
If a message arrives while its endpoint is being removed (because
the rpmsg driver was removed, or a recovery of a remote processor
has kicked in) we must ensure atomicity, i.e.:
- Either the ept is removed before it is found
or
- The ept is found but will not be freed until the callback returns
This is achieved by maintaining a per-ept reference count, which,
when drops to zero, will trigger deallocation of the ept.
With this in hand, it is now forbidden to directly deallocate
epts once they have been added to the endpoints idr.
Cc: stable <stable@vger.kernel.org>
Reported-by: Fernando Guzman Lugo <fernando.lugo@ti.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Remoteproc requires user space firmware loading support, so
let's select FW_LOADER explicitly to avoid painful misconfigurations
(which only show up in runtime).
Cc: stable <stable@vger.kernel.org>
Reported-by: Mark Grosen <mgrosen@ti.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
OMAP_REMOTEPROC selects REMOTEPROC and RPMSG, both of which depend
on EXPERIMENTAL, so let's have OMAP_REMOTEPROC depend on EXPERIMENTAL
too, in order to avoid the below randconfig warnings.
warning: (OMAP_REMOTEPROC) selects REMOTEPROC which has unmet direct dependencies (EXPERIMENTAL)
warning: (OMAP_REMOTEPROC) selects RPMSG which has unmet direct dependencies (EXPERIMENTAL)
Cc: stable <stable@vger.kernel.org>
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
which could lead to bad array indexing when switching clock parents.
The issue is fixed with a trivial change to the code flow in
__clk_set_parent.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJP81RmAAoJEDqPOy9afJhJob4P/j3IAxlWm5Pe/TS37MB+SdZg
CGRwOXtEoLRTrWNvTWGar9Ph+jN7onQsbAdi+GOsffnY12rg9GCA0oq5irzHHGWq
r3pv1oFDj8tF6Y1iNFswbBWlZxmIQVWb18r8z8bUBsrdLLYLLa+dOBgcLUO1qin0
pJ70RZE0Gd0DjElNXuO2rPigueeO3GMVaasNacTmSgv5wAQteMfUQcmvOBEf2Yh2
Wi064oMBYUHEUCCVyBfqUNPn+e+kB8oN2cvVxigUh+Nbw0QtgR5015XZabMre+3S
fbhZmoHVGhuAnNLEe0VoQjA7lRG/JKJmYVB3xa9Pk4CgGXEs5dJe5LhSxM4gg+W3
Uo0op6QDmIEpxeb3/7DALbmHpceiVZWOB9UJyK6ZD0iG961CBO9eumjuWP6QywiE
sg5ijx0KZ6ssSyKP7yBWW52z2CxraXJsrwdMQCcXAKXOSOlNjQOR0lr4pbMfbIiz
zZ20opZur+BIugt7GKBt4tn4z/9+c49GS6akVGSlYVqszVLo8g4fdkSw3lYlN3jy
XhMKvey3nWmia5BYabpdsOWhvntVPeT86iCJdpONvkiYYm2Vkm/1CSQeom4vVRep
kUjxMLApkuJ5KB/YLuqjOfPsqglPiqzmn5UkvBZ2ZDakpFbIo/s6Z9zWR4hMw/J7
F4uArxEHITMJutHO6msD
=0z1d
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux
Pull fix to common clk framework from Michael Turquette:
"The previous set of common clk fixes for -rc5 left an uninitialized
int which could lead to bad array indexing when switching clock
parents. The issue is fixed with a trivial change to the code flow in
__clk_set_parent."
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux:
clk: fix parent validation in __clk_set_parent()
I really shouldn't do important things late in the day. It seems
that I get careless.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=pDob
-----END PGP SIGNATURE-----
Merge tag 'md-3.5-fixes' of git://neil.brown.name/md
Pull raid10 build failure fix from NeilBrown:
"I really shouldn't do important things late in the day. It seems that
I get careless."
* tag 'md-3.5-fixes' of git://neil.brown.name/md:
md/raid10: fix careless build error
Pull networking update from David Miller:
1) Fix RX sequence number handling in mwifiex, from Stone Piao.
2) Netfilter ipset mis-compares device names, fix from Florian
Westphal.
3) Fix route leak in ipv6 IPVS, from Eric Dumazet.
4) NFS fixes. Several buffer overflows in NCI layer from Dan
Rosenberg, and release sock OOPS'er fix from Eric Dumazet.
5) Fix WEP handling ath9k, we started using a bit the chip provides to
indicate undecrypted packets but that bit turns out to be unreliable
in certain configurations. Fix from Felix Fietkau.
6) Fix Kconfig dependency bug in wlcore, from Randy Dunlap.
7) New USB IDs for rtlwifi driver from Larry Finger.
8) Fix crashes in qmi_wwan usbnet driver when disconnecting, from Bjørn
Mork.
9) Gianfar driver programs coalescing settings properly in single queue
mode, but does not do so in multi-queue mode. Fix from Claudiu
Manoil.
10) Missing module.h include in davinci_cpdma.c, from Daniel Mack.
11) Need dummy handler for IPSET_CMD_NONE otherwise we crash in ipset if
we get this via nfnetlink, fix from Tomasz Bursztyka.
12) Missing RCU unlock in nfnetlink error path, also from Tomasz.
13) Fix divide by zero in igbvf when the user tries to set an RX
coalescing value of 0 usecs, from Mitch A Williams.
14) We can process SCTP sacks for the wrong transport, oops. Fix from
Neil Horman.
15) Remove hw IP payload checksumming from e1000e driver. This has zery
value in our stack, and turning it on creates a very unintuitive
restriction for users when using jumbo MTUs.
Specifically, when IP payload checksums are on you cannot use both
receive hashing offload and jumbo MTU. Fix from Bruce Allan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (27 commits)
e1000e: remove use of IP payload checksum
sctp: be more restrictive in transport selection on bundled sacks
igbvf: fix divide by zero
netfilter: nfnetlink: fix missing rcu_read_unlock in nfnetlink_rcv_msg
netfilter: ipset: fix crash if IPSET_CMD_NONE command is sent
davinci_cpdma: include linux/module.h
gianfar: Fix RXICr/TXICr programming for multi-queue mode
net: Downgrade CAP_SYS_MODULE deprecated message from error to warning.
net: qmi_wwan: fix Oops while disconnecting
mwifiex: fix memory leak associated with IE manamgement
ath9k: fix panic caused by returning a descriptor we have queued for reuse
mac80211: correct behaviour on unrecognised action frames
ath9k: enable serialize_regmode for non-PCIE AR9287
rtlwifi: rtl8192cu: New USB IDs
NFC: Return from rawsock_release when sk is NULL
iwlwifi: fix activating inactive stations
wlcore: drop INET dependency
ath9k: fix dynamic WEP related regression
NFC: Prevent multiple buffer overflows in NCI
netfilter: update location of my trees
...
build error introduced by commit b357f04a67
That function doesn't get extra args until a later patch. Bother.
Reported-by: Fengguang Wu <wfg@linux.intel.com>
Reported-by: Simon Kirby <sim@hostway.ca>
Reported-by: Tobias Klausmann <tobias.johannes.klausmann@mni.thm.de>
Signed-off-by: NeilBrown <neilb@suse.de>
In commit 070ad7e793 ("floppy: convert to delayed work and
single-thread wq") the 'fd_timeout' timer was converted to a delayed
work. However, the "del_timer(&fd_timeout)" was lost in the process,
and any previous pending timeouts would stay active when we then
re-queued the timeout.
This resulted in the floppy probe sequence having a (stale) 20s timeout
rather than the intended 3s timeout, and thus made booting with the
floppy driver (but no actual floppy controller) take much longer than it
should.
Of course, there's little reason for most people to compile the floppy
driver into the kernel at all, which is why most people never noticed.
Canceling the delayed work where we used to do the del_timer() fixes the
issue, and makes the floppy probing use the proper new timeout instead.
The three second timeout is still very wasteful, but better than the 20s
one.
Reported-and-tested-by: Andi Kleen <ak@linux.intel.com>
Reported-and-tested-by: Calvin Walton <calvin.walton@kepstin.ca>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull block bits from Jens Axboe:
"As vacation is coming up, thought I'd better get rid of my pending
changes in my for-linus branch for this iteration. It contains:
- Two patches for mtip32xx. Killing a non-compliant sysfs interface
and moving it to debugfs, where it belongs.
- A few patches from Asias. Two legit bug fixes, and one killing an
interface that is no longer in use.
- A patch from Jan, making the annoying partition ioctl warning a bit
less annoying, by restricting it to !CAP_SYS_RAWIO only.
- Three bug fixes for drbd from Lars Ellenberg.
- A fix for an old regression for umem, it hasn't really worked since
the plugging scheme was changed in 3.0.
- A few fixes from Tejun.
- A splice fix from Eric Dumazet, fixing an issue with pipe
resizing."
* 'for-linus' of git://git.kernel.dk/linux-block:
scsi: Silence unnecessary warnings about ioctl to partition
block: Drop dead function blk_abort_queue()
block: Mitigate lock unbalance caused by lock switching
block: Avoid missed wakeup in request waitqueue
umem: fix up unplugging
splice: fix racy pipe->buffers uses
drbd: fix null pointer dereference with on-congestion policy when diskless
drbd: fix list corruption by failing but already aborted reads
drbd: fix access of unallocated pages and kernel panic
xen/blkfront: Add WARN to deal with misbehaving backends.
blkcg: drop local variable @q from blkg_destroy()
mtip32xx: Create debugfs entries for troubleshooting
mtip32xx: Remove 'registers' and 'flags' from sysfs
blkcg: fix blkg_alloc() failure path
block: blkcg_policy_cfq shouldn't be used if !CONFIG_CFQ_GROUP_IOSCHED
block: fix return value on cfq_init() failure
mtip32xx: Remove version.h header file inclusion
xen/blkback: Copy id field when doing BLKIF_DISCARD.
A recursive lockdep warning occurs if you call
regulator_set_optimum_mode() on a regulator with a supply because
there is no nesting annotation for the rdev->mutex. To avoid this
warning, get the supply's load before locking the regulator's
mutex to avoid grabbing the same class of lock twice.
=============================================
[ INFO: possible recursive locking detected ]
3.4.0 #3257 Tainted: G W
---------------------------------------------
swapper/0/1 is trying to acquire lock:
(&rdev->mutex){+.+.+.}, at: [<c036e9e0>] regulator_get_voltage+0x18/0x38
but task is already holding lock:
(&rdev->mutex){+.+.+.}, at: [<c036ef38>] regulator_set_optimum_mode+0x24/0x224
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&rdev->mutex);
lock(&rdev->mutex);
*** DEADLOCK ***
May be due to missing lock nesting notation
3 locks held by swapper/0/1:
#0: (&__lockdep_no_validate__){......}, at: [<c03dbb48>] __driver_attach+0x40/0x8c
#1: (&__lockdep_no_validate__){......}, at: [<c03dbb58>] __driver_attach+0x50/0x8c
#2: (&rdev->mutex){+.+.+.}, at: [<c036ef38>] regulator_set_optimum_mode+0x24/0x224
stack backtrace:
[<c001521c>] (unwind_backtrace+0x0/0x12c) from [<c00cc4d4>] (validate_chain+0x760/0x1080)
[<c00cc4d4>] (validate_chain+0x760/0x1080) from [<c00cd744>] (__lock_acquire+0x950/0xa10)
[<c00cd744>] (__lock_acquire+0x950/0xa10) from [<c00cd990>] (lock_acquire+0x18c/0x1e8)
[<c00cd990>] (lock_acquire+0x18c/0x1e8) from [<c080c248>] (mutex_lock_nested+0x68/0x3c4)
[<c080c248>] (mutex_lock_nested+0x68/0x3c4) from [<c036e9e0>] (regulator_get_voltage+0x18/0x38)
[<c036e9e0>] (regulator_get_voltage+0x18/0x38) from [<c036efb8>] (regulator_set_optimum_mode+0xa4/0x224)
...
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The below commit introduced a bug in __clk_set_parent()
which could cause it to *skip* the parent validation
which makes sure the parent passed to the api is a valid
one.
commit 7975059db5
Author: Rajendra Nayak <rnayak@ti.com>
Date: Wed Jun 6 14:41:31 2012 +0530
clk: Allow late cache allocation for clk->parents
This was identified by the following compiler warning..
drivers/clk/clk.c: In function '__clk_set_parent':
drivers/clk/clk.c:1083:5: warning: 'i' may be used uninitialized in this function [-Wuninitialized]
.. as reported by Marc Kleine-Budde.
There were various options discussed on how to fix this, one
being initing 'i' to clk->num_parents, but the below approach
was found to be more appropriate as it also makes the 'parent
validation' code simpler to read.
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Cc: stable@kernel.org
Pull drm fixes from Dave Airlie:
"One regression fix, two radeon fixes (one for an oops), and an i915
fix to unload framebuffers earlier.
We originally were going to leave the i915 fix until -next, but grub2
in some situations causes vesafb/efifb to be loaded now, and this
causes big slowdowns, and I have reports in rawhide I'd like to have
fixed."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: kick any firmware framebuffers before claiming the gtt
drm: edid: Don't add inferred modes with higher resolution
drm/radeon: fix rare segfault
drm/radeon: fix VM page table setup on SI
You go away for 2 weeks vacation and what do you get when you come back?
Piles of bugs :-)
Some found by inspection, some by testing, some during use in the field,
and some while developing for the next window...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=vv4r
-----END PGP SIGNATURE-----
Merge tag 'md-3.5-fixes' of git://neil.brown.name/md
Pull md fixes from NeilBrown:
"md: collection of bug fixes for 3.5
You go away for 2 weeks vacation and what do you get when you come
back? Piles of bugs :-)
Some found by inspection, some by testing, some during use in the
field, and some while developing for the next window..."
* tag 'md-3.5-fixes' of git://neil.brown.name/md:
md: fix up plugging (again).
md: support re-add of recovering devices.
md/raid1: fix bug in read_balance introduced by hot-replace
raid5: delayed stripe fix
md/raid456: When read error cannot be recovered, record bad block
md: make 'name' arg to md_register_thread non-optional.
md/raid10: fix failure when trying to repair a read error.
md/raid5: fix refcount problem when blocked_rdev is set.
md:Add blk_plug in sync_thread.
md/raid5: In ops_run_io, inc nr_pending before calling md_wait_for_blocked_rdev
md/raid5: Do not add data_offset before call to is_badblock
md/raid5: prefer replacing failed devices over want-replacement devices.
md/raid10: Don't try to recovery unmatched (and unused) chunks.
Currently the gpio _runtime_resume/suspend functions are calling the
get_context_loss_count() platform function if the function is populated for
a gpio bank. This function is used to determine if the gpio bank logic state
needs to be restored due to a power transition. This function will be populated
for all banks, but it should only be called for banks that have the
"loses_context" variable set. It is pointless to call this if loses_context is
false as we know the context will never be lost and will not need restoring.
For all OMAP2+ devices gpio bank-0 is in an always-on power domain and so will
never lose context. We found that the get_context_loss_count() was being called
for bank-0 during the probe and returning 1 instead of 0 indicating that the
context had been lost. This was causing the context restore function to be
called at probe time for this bank and because the context had never been saved,
was restoring an invalid state. This ultimately resulted in a crash [1].
This issue is a regression that was exposed by commit 1b1287032 (gpio/omap: fix
missing check in *_runtime_suspend()).
There are multiple bugs here that need to be addressed ...
1. Why the always-on power domain returns a context loss count of 1? This needs
to be fixed in the power domain code [2]. However, the gpio driver should not
assume the loss count is 0 to begin with.
2. The omap gpio driver should never be calling get_context_loss_count for a
gpio bank in a always-on domain. This is pointless and adds unneccessary
overhead.
3. The OMAP gpio driver assumes that the initial power domain context loss count
will be 0 at the time the gpio driver is probed. However, it could be
possible that this is not the case and an invalid context restore could be
performed during the probe. To avoid this only populate the
get_context_loss_count() function pointer after the initial call to
pm_runtime_get() has occurred. This will ensure that the first
pm_runtime_put() initialised the loss count correctly.
This patch addresses issues 2 and 3 above.
[1] http://marc.info/?l=linux-omap&m=134065775323775&w=2
[2] http://marc.info/?l=linux-omap&m=134100413303810&w=2
Cc: Kevin Hilman <khilman@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Cc: Franky Lin <frankyl@broadcom.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: NeilBrown <neilb@suse.de>
Reported-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Franky Lin <frankyl@broadcom.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Tested-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
If CONFIG_DM_DEBUG_SPACE_MAPS is enabled and memory is fragmented and a
sufficiently-large metadata device is used in a thin pool then the space
map checker will fail to allocate the memory it requires.
Switch from kmalloc to vmalloc to allow larger virtually contiguous
allocations for the space map checker's internal count arrays.
Reported-by: Vivek Goyal <vgoyal@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If CONFIG_DM_DEBUG_SPACE_MAPS is enabled and dm_sm_checker_create()
fails, dm_tm_create_internal() would still return success even though it
cleaned up all resources it was supposed to have created. This will
lead to a kernel crash:
general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC
...
RIP: 0010:[<ffffffff81593659>] [<ffffffff81593659>] dm_bufio_get_block_size+0x9/0x20
Call Trace:
[<ffffffff81599bae>] dm_bm_block_size+0xe/0x10
[<ffffffff8159b8b8>] sm_ll_init+0x78/0xd0
[<ffffffff8159c1a6>] sm_ll_new_disk+0x16/0xa0
[<ffffffff8159c98e>] dm_sm_disk_create+0xfe/0x160
[<ffffffff815abf6e>] dm_pool_metadata_open+0x16e/0x6a0
[<ffffffff815aa010>] pool_ctr+0x3f0/0x900
[<ffffffff8158d565>] dm_table_add_target+0x195/0x450
[<ffffffff815904c4>] table_load+0xe4/0x330
[<ffffffff815917ea>] ctl_ioctl+0x15a/0x2c0
[<ffffffff81591963>] dm_ctl_ioctl+0x13/0x20
[<ffffffff8116a4f8>] do_vfs_ioctl+0x98/0x560
[<ffffffff8116aa51>] sys_ioctl+0x91/0xa0
[<ffffffff81869f52>] system_call_fastpath+0x16/0x1b
Fix the space map checker code to return an appropriate ERR_PTR and have
dm_sm_disk_create() and dm_tm_create_internal() check for it with
IS_ERR.
Reported-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cleanup the shadow table before destroying the transaction manager.
Reference: leak was identified with kmemleak when running
test_discard_random_sectors in the thinp-test-suite.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Userland sometimes sees a corrupt metadata block if metadata is changing
rapidly when a metadata snapshot is reserved for userland, To make the
problem go away, commit before we take the metadata snapshot (which is a
sensible thing to do anyway).
The checksums mean userland spots this corruption immediately so there's
no risk of acting on incorrect data. No corruption exists from the
kernel's point of view, and thin_check passes after pool shutdown.
I believe this is to do with shared blocks at the first level of the
{device, mapping} btree. Prior to the metadata-snap support no sharing
at this level was possible, so this patch is only required after commit
cc8394d86f ("dm thin: provide userspace
access to pool metadata").
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Especially vesafb likes to map everything as uc- (yikes), and if that
mapping hangs around still while we try to map the gtt as wc the
kernel will downgrade our request to uc-, resulting in abyssal
performance.
Unfortunately we can't do this as early as readon does (i.e. as the
first thing we do when initializing the hw) because our fb/mmio space
region moves around on a per-gen basis. So I've had to move it below
the gtt initialization, but that seems to work, too. The important
thing is that we do this before we set up the gtt wc mapping.
Now an altogether different question is why people compile their
kernels with vesafb enabled, but I guess making things just work isn't
bad per se ...
v2:
- s/radeondrmfb/inteldrmfb/
- fix up error handling
v3: Kill #ifdef X86, this is Intel after all. Noticed by Ben Widawsky.
v4: Jani Nikula complained about the pointless bool primary
initialization.
v5: Don't oops if we can't allocate, noticed by Chris Wilson.
v6: Resolve conflicts with agp rework and fixup whitespace.
This is commit e188719a28 in drm-next.
Backport to 3.5 -fixes queue requested by Dave Airlie - due to grub
using vesa on fedora their initrd seems to load vesafb before loading
the real kms driver. So tons more people actually experience a
dead-slow gpu. Hence also the Cc: stable.
Cc: stable@vger.kernel.org
Reported-and-tested-by: "Kilarski, Bernard R" <bernard.r.kilarski@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When a monitor EDID doesn't give the preferred bit, driver assumes
that the mode with the higest resolution and rate is the preferred
mode. Meanwhile the recent changes for allowing more modes in the
GFT/CVT ranges give actually more modes, and some modes may be over
the native size. Thus such a mode would be picked up as the preferred
mode although it's no native resolution.
For avoiding such a problem, this patch limits the addition of
inferred modes by checking not to be greater than other modes.
Also, it checks the duplicated mode entry at the same time.
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In gem idle/busy ioctl the radeon object was derefenced after
drm_gem_object_unreference_unlocked which in case the object
have been destroyed lead to use of a possibly free pointer with
possibly wrong data.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The value returned by "mddev_check_plug" is only valid until the
next 'schedule' as that will unplug things. This could happen at any
call to mempool_alloc.
So just calling mddev_check_plug at the start doesn't really make
sense.
So call it just before, or just after, queuing things for the thread.
As the action that happens at unplug is to wake the thread, this makes
lots of sense.
If we cannot add a plug (which requires a small GFP_ATOMIC alloc) we
wake thread immediately.
RAID5 is a bit different. Requests are queued for the thread and the
thread is woken by release_stripe. So we don't need to wake the
thread on failure.
However the thread doesn't perform certain actions when there is any
active plug, so it is important to install a plug before waking the
thread. So for RAID5 we install the plug *before* queuing the request
and waking the thread.
Without this patch it is possible for raid1 or raid10 to queue a
request without then waking the thread, resulting in the array locking
up.
Also change raid10 to only flush_pending_write when there are not
active plugs, just like raid1.
This patch is suitable for 3.0 or later. I plan to submit it to
-stable, but I'll like to let it spend a few weeks in mainline
first to be sure it is completely safe.
Signed-off-by: NeilBrown <neilb@suse.de>
We currently only allow a device to be re-added if it appear to be
in-sync. This is overly restrictive as it may be desirable to re-add
a device that is in the middle of recovery.
So remove the test for "InSync" - the test on rdev->raid_disk is
sufficient to ensure that the re-add will succeed.
Reported-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Tested-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When we added hot_replace we doubled the number of devices
that could be in a RAID1 array. So we doubled how far read_balance
would search. Unfortunately we didn't double the point at which
it looped back to the beginning - so it effectively loops over
all non-replacement disks twice.
This doesn't cause bad behaviour, but it pointless and means we
never read from replacement devices.
Signed-off-by: NeilBrown <neilb@suse.de>
There isn't locking setting STRIPE_DELAYED and STRIPE_PREREAD_ACTIVE bits, but
the two bits have relationship. A delayed stripe can be moved to hold list only
when preread active stripe count is below IO_THRESHOLD. If a stripe has both
the bits set, such stripe will be in delayed list and preread count not 0,
which will make such stripe never leave delayed list.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
We may not be able to fix a bad block if:
- the array is degraded
- the over-write fails.
In these cases we currently eject the device, but we should
record a bad block if possible.
Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Having the 'name' arg optional and defaulting to the current
personality name is no necessary and leads to errors, as when
changing the level of an array we can end up using the
name of the old level instead of the new one.
So make it non-optional and always explicitly pass the name
of the level that the array will be.
Reported-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
commit 58c54fcca3
md/raid10: handle further errors during fix_read_error better.
in 3.1 added "r10_sync_page_io" which takes an IO size in sectors.
But we were passing the IO size in bytes!!!
This resulting in bio_add_page failing, and empty request being sent
down, and a consequent BUG_ON in scsi_lib.
[fix missing space in error message at same time]
This fix is suitable for 3.1.y and later.
Cc: stable@vger.kernel.org
Reported-by: Christian Balzer <chibi@gol.com>
Signed-off-by: NeilBrown <neilb@suse.de>
commit 43220aa0f2
md/raid5: fix a hang on device failure.
fixed a hang, but introduced a refcounting in-balance so
that if the presence of bad-blocks ever caused an rdev to
be 'blocked' we would increment the refcount on the rdev and
never decrement it.
So added the needed rdev_dec_pending when md_wait_for_blocked_rdev
is not called.
Reported-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
In ops_run_io(), the call to md_wait_for_blocked_rdev will decrement
nr_pending so we lose the reference we hold on the rdev.
So atomic_inc it first to maintain the reference.
This bug was introduced by commit 73e92e51b7
md/raid5. Don't write to known bad block on doubtful devices.
which appeared in 3.0, so patch is suitable for stable kernels since
then.
Cc: stable@vger.kernel.org
Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
In chunk_aligned_read() we are adding data_offset before calling
is_badblock. But is_badblock also adds data_offset, so that is bad.
So move the addition of data_offset to after the call to
is_badblock.
This bug was introduced by commit 31c176ecdf
md/raid5: avoid reading from known bad blocks.
which first appeared in 3.0. So that patch is suitable for any
-stable kernel from 3.0.y onwards. However it will need minor
revision for most of those (as the comment didn't appear until
recently).
Cc: stable@vger.kernel.org
Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
If a RAID5 has both a failed device and a device marked as
'WantReplacement', then we should preferentially replace the failed
device.
However the current code replaces whichever is found first.
So split into 2 loops, check fail failed/missing first, and only check
for WantReplacement if nothing is failed or missing.
Reported-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
If a RAID10 has an odd number of chunks - as might happen when there
are an odd number of devices - the last chunk has no pair and so is
not mirrored. We don't store data there, but when recovering the last
device in an array we retry to recover that last chunk from a
non-existent location. This results in an error, and the recovery
aborts.
When we get to that last chunk we should just stop - there is nothing
more to do anyway.
This bug has been present since the introduction of RAID10, so the
patch is appropriate for any -stable kernel.
Cc: stable@vger.kernel.org
Reported-by: Christian Balzer <chibi@gol.com>
Tested-by: Christian Balzer <chibi@gol.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The Microsoft LifeChat 3000 USB headset was causing a very reproducible
hang whenever it was plugged in. At first, I thought the host
controller was producing bad transfer events, because the log was filled
with errors like:
xhci_hcd 0000:00:14.0: ERROR Transfer event TRB DMA ptr not part of current TD
However, it turned out to be an xHCI driver bug in the ring expansion
patches. The bug is triggered When there are two ring segments, and a
TD that ends just before a link TRB, like so:
______________ _____________
| | ---> | setup TRB B |
______________ | _____________
| | | | data TRB B |
______________ | _____________
| setup TRB A | <-- deq | | data TRB B |
______________ | _____________
| data TRB A | | | | <-- enq, deq''
______________ | _____________
| status TRB A | | | |
______________ | _____________
| link TRB |--------------- | link TRB |
_____________ <--- deq' _____________
TD A (the first control transfer) stalls on the data phase. That halts
the ring. The xHCI driver moves the hardware dequeue pointer to the
first TRB after the stalled transfer, which happens to be the link TRB.
Once the Set TR dequeue pointer command completes, the function
update_ring_for_set_deq_completion runs. That function is supposed to
update the xHCI driver's dequeue pointer to match the internal hardware
dequeue pointer. On the first call this would work fine, and the
software dequeue pointer would move to deq'.
However, if the transfer immediately after that stalled (TD B in this
case), another Set TR Dequeue command would be issued. That would move
the hardware dequeue pointer to deq''. Once that command completed,
update_ring_for_set_deq_completion would run again.
The original code would unconditionally increment the software dequeue
pointer, which moved the pointer off the ring segment into la-la-land.
The while loop would happy increment the dequeue pointer (possibly
wrapping it) until it matched the hardware pointer value.
The while loop would also access all the memory in between the first
ring segment and the second ring segment to determine if it was a link
TRB. This could cause general protection faults, although it was
unlikely because the ring segments came from a DMA pool, and would often
have consecutive memory addresses.
If nothing in that space looked like a link TRB, the deq_seg pointer for
the ring would remain on the first segment. Thus, the deq_seg and the
software dequeue pointer would get out of sync.
When the next transfer event came in after the stalled transfer, the
xHCI driver code would attempt to convert the software dequeue pointer
into a DMA address in order to compare the DMA address for the completed
transfer. Since the deq_seg and the dequeue pointer were out of sync,
xhci_trb_virt_to_dma would return NULL.
The transfer event would get ignored, the transfer would eventually
timeout, and we would mistakenly convert the finished transfer to no-op
TRBs. Some kernel driver (maybe xHCI?) would then get stuck in an
infinite loop in interrupt context, and the whole machine would hang.
This patch should be backported to kernels as old as 3.4, that contain
the commit b008df60c6 "xHCI: count free
TRBs on transfer ring"
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Andiry Xu <andiry.xu@amd.com>
Cc: stable@vger.kernel.org
The host controller port status register supports CAS (Cold Attach
Status) bit. This bit could be set when USB3.0 device is connected
when system is in Sx state. When the system wakes to S0 this port
status with CAS bit is reported and this port can't be used by any
device.
When CAS bit is set the port should be reset by warm reset. This
was not supported by xhci driver.
The issue was found when pendrive was connected to suspended
platform. The link state of "Compliance Mode" was reported together
with CAS bit. This link state was also not supported by xhci and
core/hub.c.
The CAS bit is defined only for xhci root hub port and it is
not supported on regular hubs. The link status is used to force
warm reset on port. Make the USB core issue a warm reset when port
is in ether the 'inactive' or 'compliance mode'. Change the xHCI driver
to report 'compliance mode' when the CAS is set. This force warm reset
on the root hub port.
This patch should be backported to stable kernels as old as 3.2, that
contain the commit 10d674a82e "USB: When
hot reset for USB3 fails, try warm reset."
Signed-off-by: Stanislaw Ledwon <staszek.ledwon@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Andiry Xu <andiry.xu@amd.com>
Cc: stable@vger.kernel.org
write_file_bool() modifies 32 bits of data, so "amd_iommu_unmap_flush"
needs to be 32 bits as well or we'll corrupt memory. Fortunately it
looks like the data is aligned with a gap after the declaration so this
is harmless in production.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
allo_pdir() is called in smmu_iommu_domain_init() with spin_lock
held. memory allocations in it have to be atomic/unsleepable.
Signed-off-by: Hiroshi DOYU <hdoyu@nvidia.com>
Reported-by: Chris Wright <chrisw@sous-sol.org>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Cc: stable@vger.kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Currently only used when packet split mode is enabled with jumbo frames,
IP payload checksum (for fragmented UDP packets) is mutually exclusive with
receive hashing offload since the hardware uses the same space in the
receive descriptor for the hardware-provided packet checksum and the RSS
hash, respectively. Users currently must disable jumbos when receive
hashing offload is enabled, or vice versa, because of this incompatibility.
Since testing has shown that IP payload checksum does not provide any real
benefit, just remove it so that there is no longer a choice between jumbos
or receive hashing offload but not both as done in other Intel GbE drivers
(e.g. e1000, igb).
Also, add a missing check for IP checksum error reported by the hardware;
let the stack verify the checksum when this happens.
CC: stable <stable@vger.kernel.org> [3.4]
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using ethtool -C ethX rx-usecs 0 crashes with a divide by zero.
Refactor this function to fix this issue and make it more clear
what the intent of each conditional is. Add comment regarding
using a setting of zero.
CC: stable <stable@vger.kernel.org> [3.3+]
CC: David Ahern <daahern@cisco.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull ACPI & Power Management patches from Len Brown.
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
acpi_pad: fix power_saving thread deadlock
ACPI video: Still use ACPI backlight control if _DOS doesn't exist
ACPI, APEI, Avoid too much error reporting in runtime
ACPI: Add a quirk for "AMILO PRO V2030" to ignore the timer overriding
ACPI: Remove one board specific WARN when ignoring timer overriding
ACPI: Make acpi_skip_timer_override cover all source_irq==0 cases
ACPI, x86: fix Dell M6600 ACPI reboot regression via DMI
ACPI sysfs.c strlen fix
The acpi_pad driver can get stuck in destroy_power_saving_task()
waiting for kthread_stop() to stop a power_saving thread. The problem
is that the isolated_cpus_lock mutex is owned when
destroy_power_saving_task() calls kthread_stop(), which waits for a
power_saving thread to end, and the power_saving thread tries to
acquire the isolated_cpus_lock when it calls round_robin_cpu(). This
patch fixes the issue by making round_robin_cpu() use its own mutex.
https://bugzilla.kernel.org/show_bug.cgi?id=42981
Cc: stable@vger.kernel.org
Signed-off-by: Stuart Hayes <Stuart_Hayes@Dell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This fixes a regression in 3.4-rc1 caused by commit
ea9f8856bd
(ACPI video: Harden video bus adding.)
Some platforms don't have _DOS control method, but the ACPI
backlight still works.
We should not invoke _DOS for these platforms.
https://bugzilla.kernel.org/show_bug.cgi?id=43168
Cc: Igor Murzov <intergalactic.anonymous@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* Fix for a bug in async suspend error code path causing parents to wait
forever for their children in case of a suspend error from Mandeep Singh
Baines (-stable metarial).
* Fix for a suspend regression related to earlier changes in the ACPI
cpuidle driver from Deepthi Dharwar.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=a9hl
-----END PGP SIGNATURE-----
Merge tag 'pm-for-3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael J. Wysocki:
* Fix for a bug in async suspend error code path causing parents to
wait forever for their children in case of a suspend error from
Mandeep Singh Baines (-stable metarial).
* Fix for a suspend regression related to earlier changes in the ACPI
cpuidle driver from Deepthi Dharwar.
* tag 'pm-for-3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / ACPI: Fix suspend/resume regression caused by cpuidle cleanup.
PM / Sleep: Prevent waiting forever on asynchronous suspend after abort
Pull x86 fixes from Ingo Molnar.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, cpufeature: Remove stray %s, add -w to mkcapflags.pl
x86, cpufeature: Catch duplicate CPU feature strings
x86, cpufeature: Rename X86_FEATURE_DTS to X86_FEATURE_DTHERM
x86: Fix kernel-doc warnings
x86, compat: Use test_thread_flag(TIF_IA32) in compat signal delivery
Pull oprofile fixlet from Ingo Molnar.
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
oprofile: perf: use NR_CPUS instead or nr_cpumask_bits for static array
Cayman and trinity allow for variable sized VM page
tables, but SI requires that all page tables be the
same size. The current code assumes variablely sized
VM page tables so SI may end up with part of each page
table overlapping with other memory which could end
up being interpreted by the VM hw as garbage.
Change the code to better accomodate SI. Allocate enough
space for at least 2 full page tables and always set
last_pfn to max_pfn on SI so each VM is backed by a full
page table. This limits us to only 2 VMs active at any
given time on SI. This will be rectified and the code can
be reunified once we move to two level page tables.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This fixes a number of warnings such as:
CC drivers/net/ethernet/ti/davinci_cpdma.o
drivers/net/ethernet/ti/davinci_cpdma.c:279:1: warning: data definition
has no type or storage class
drivers/net/ethernet/ti/davinci_cpdma.c:279:1: warning: type defaults to
‘int’ in declaration of ‘EXPORT_SYMBOL_GPL’
drivers/net/ethernet/ti/davinci_cpdma.c:279:1: warning: parameter names
(without types) in function declaration
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some models, such as 0xE6, report more fingers than we process.
Reported-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Tested-by: Nils Kanning <nils@kanning.de>
Tested-by: Rafi Rubin <rafi@seas.upenn.edu>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
rep_data is not an array anymore, so taking it's address when passing to
wacom_get_report() is wrong.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Tested-by: Rafi Rubin <rafi@seas.upenn.edu>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
John Linville says:
====================
Amitkumar Karwar gives us two mwifiex fixes: one fixes some skb
manipulations when handling some event messages; and another that
does some similar fixing on an error path.
Avinash Patil gives us a fix for for a memory leak in mwifiex.
Dan Rosenberg offers an NFC NCI fix to enforce some message length
limits to prevent buffer overflows.
Eliad Peller provides a mac80211 fix to prevent some frames from
being built with an invalid BSSID.
Eric Dumazet sends an NFC fix to prevent a BUG caused by a NULL
pointer dereference.
Felix Fietkau has an ath9k fix for a regression causing
LEAP-authenticated connection failures.
Johannes Berg provides an iwlwifi fix that eliminates some log SPAM
after an authentication/association timeout. He also provides a
mac80211 fix to prevent incorrectly addressing certain action frames
(and in so doing, to comply with the 802.11 specs).
Larry Finger provides a few USB IDs for the rtl8192cu driver --
should be harmless.
Panayiotis Karabassis provices a one-liner to fix kernel bug 42903
(a system freeze).
Randy Dunlap provides a one-line Kconfig change to prevent build
failures with some configurations.
Stone Piao provides an mwifiex sequence numbering fix and a fix
to prevent mwifiex from attempting to include eapol frames in an
aggregation frame.
Finally, Tom Hughes provides an ath9k fix for a NULL pointer
dereference.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The correct behavior is to program the interrupt coalescing regs
(RXICr/TXICr) in accordance with the Rx/Tx Q's "rx/txcoalescing"
flag. That is, if the coalescing flag is 0 for a given Rx/Tx queue
then the corresponding coalescing register should be cleared.
This behavior is correctly implemented for the single-queue mode
(SQ_SG_MODE), but not for the multi-queue mode (MQ_MG_MODE).
This fixes the later case.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull watchdog fixes from Wim Van Sebroeck:
"This fixes:
- the WDIOC_GETSTATUS return value
- the unregister of all NMI events on exit
- the loading of the iTCO_wdt driver after the conversion to the
lpc_ich mfd model."
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: core: fix WDIOC_GETSTATUS return value
watchdog: hpwdt: Unregister NMI events on exit.
watchdog: iTCO_wdt: add platform driver module alias
'IS_ENABLED()' macro usage: should be 'IS_ENABLED(CONFIG_DEBUG_FS)',
but we had 'IS_ENABLED(DEBUG_FS)'. Also fix incorrect assertion.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJP7Hx+AAoJECmIfjd9wqK04FEP/3NC0qMlleuEcHv9AFwOJ1PB
rn1PDjz6kuEjZ1/xhGFoboBOUj577qyzIP6IvG7MqSH66Yc8gBF+sPbKWWglx7wB
i2y7/Fi4lHM3w59GfvnOhdI7McklhPyl3R183MZ3EBJk4V0LPi2rXsl7G5puLNgG
XkJuOjXLXZPgyeMR+DlBsoaaxBMihnh/pdpUAyLER1cQdzQwCzba82tNrMgnCp7i
TIFTPtn+LmEQyHcqXx5ub/FV6BiEUXIJbkKlp5Ajqyh/olSNtGdCHRrP5MXpU2kI
DmtyMvp+3PBHxrUYQjXT6uerL9uXhIUyRv49qO0tS68fUg44JCFflmPkoV9qEvvl
ADbOqklx1DWdVCiZdhXWe1GFhf6U+TOoUyeiIzGIy0fIIlycNl915F4LzxVUqQKm
yoqouEvzqd1LIAsopakF2DDIKoK6ViWmHBkuN04B+u+iab4DC4aX3vgxq+Ie8mqA
0QNIamovk/2MR2665XhbARu0yDSEmGZvD6dkuSAgXIxjw7tdvvlY7pkSouWTOSR0
fbqPrhgbRON+mT4Fcrb5dMq+PAiOTw5kp7az90+U6i1oLm5TY8CaHt3UvmdspOM/
UeHRhLR8o/RhfnvnexiOxIWtQGCX+CCuePe9oN/fQabj9dfvKI1iR+zoyheFLwiT
HxaU6I7oVYQVkeifNJVV
=iZTv
-----END PGP SIGNATURE-----
Merge tag 'upstream-3.5-rc5' of git://git.infradead.org/linux-ubifs
Pull ubi/ubifs fixes from Artem Bityutskiy:
"Fix the debugfs regression - we never enable it because incorrect
'IS_ENABLED()' macro usage: should be 'IS_ENABLED(CONFIG_DEBUG_FS)',
but we had 'IS_ENABLED(DEBUG_FS)'. Also fix incorrect assertion."
* tag 'upstream-3.5-rc5' of git://git.infradead.org/linux-ubifs:
UBI: correct usage of IS_ENABLED()
UBIFS: correct usage of IS_ENABLED()
UBIFS: fix assertion
In commit 7a87982420 we added
a wrapper for the WDIOC_GETSTATUS ioctl call. The code results
however in a different behaviour: it returns an error if the
driver doesn't support the status operation. This is not
according to the API that says that when we don't support
the status operation, that we just should return a 0 value.
Only when the device isn't there anymore, we should return an
error.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch is to unregister for NMI events upon exit. Also we are now
making the default setting for allow_kdump enabled.
Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The recent conversion of iTCO_wdt resulted in the driver no longer
getting loaded automatically, since it no longer has a
MODULE_DEVICE_TABLE() included. As the lpc_ich driver now creates a
platform device, auto-loading can easily be done by having a respective
module alias in place.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Aaron Sierra <asierra@xes-inc.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Pull drm fixes from Dave Airlie:
"Nearly all intel, one missing license header in nouveau, nothing
majorly earth shattering."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
Revert "drm/i915: allow PCH PWM override on IVB"
drm/nouveau: add license header to prime.
drm/i915: Fix eDP blank screen after S3 resume on HP desktops
drm/i915: rip out the PM_IIR WARN
Pull networking update from David Miller:
1) Pairing and deadlock fixes in bluetooth from Johan Hedberg.
2) Add device IDs for AR3011 and AR3012 bluetooth chips. From
Giancarlo Formicuccia and Marek Vasut.
3) Fix wireless regulatory deadlock, from Eliad Peller.
4) Fix full TX ring panic in bnx2x driver, from Eric Dumazet.
5) Revert the two commits that added skb_orphan_try(), it causes
erratic bonding behavior with UDP clients and the gains it used to
give are mostly no longer happening due to how BQL works. From Eric
Dumazet.
6) It took two tries, but Thomas Graf fixed a problem wherein we
registered ipv6 routing procfs files before their backend data were
initialized properly.
7) Fix max GSO size setting in be2net, from Sarveshwar Bandi.
8) PHY device id mask is wrong for KSZ9021 and KS8001 chips, fix from
Jason Wang.
9) Fix use of stale SKB data pointer after skb_linearize() call in
batman-adv, from Antonio Quartulli.
10) Fix memory leak in IXGBE due to missing __GFP_COMP, from Alexander
Duyck.
11) Fix probing of Gobi devices in qmi_wwan usbnet driver, from Bjørn
Mork.
12) Fix suspend/resume and open failure handling in usbnet from Ming
Lei.
13) Attempt to fix device r8169 hangs for certain chips, from Francois
Romieu.
14) Fix advancement of RX dirty pointer in some situations in sh_eth
driver, from Yoshihiro Shimoda.
15) Attempt to fix restart of IPV6 routing table dumps when there is an
intervening table update. From Eric Dumazet.
16) Respect security_inet_conn_request() return value in ipv6 TCP. From
Neal Cardwell.
17) Add another iPAD device ID to ipheth driver, from Davide Gerhard.
18) Fix access to freed SKB in l2tp_eth_dev_xmit(), and fix l2tp lockdep
splats, from Eric Dumazet.
19) Make sure all bridge devices, regardless of whether they were
created via netlink or ioctls, have their rtnetlink ops hooked up.
From Thomas Graf and Stephen Hemminger.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (81 commits)
9p: fix min_t() casting in p9pdu_vwritef()
can: flexcan: use be32_to_cpup to handle the value of dt entry
xen/netfront: teardown the device before unregistering it.
bridge: Assign rtnl_link_ops to bridge devices created via ioctl (v2)
vhost: use USER_DS in vhost_worker thread
ixgbe: Do not pad FCoE frames as this can cause issues with FCoE DDP
net: l2tp_eth: use LLTX to avoid LOCKDEP splats
mac802154: add missed braces
net: l2tp_eth: fix l2tp_eth_dev_xmit race
net/mlx4_en: Release QP range in free_resources
net/mlx4: Use single completion vector after NOP failure
net/mlx4_en: Set correct port parameters during device initialization
ipheth: add support for iPad
caif-hsi: Add missing return in error path
caif-hsi: Bugfix - Piggyback'ed embedded CAIF frame lost
caif: Clear shutdown mask to zero at reconnect.
tcp: heed result of security_inet_conn_request() in tcp_v6_conn_request()
ipv6: fib: fix fib dump restart
batman-adv: fix race condition in TT full-table replacement
batman-adv: only drop packets of known wifi clients
...
Free ap_custom_ie before return from function.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Here are some small USB gadget bugfixes, and a few new USB device ids added to
some drivers for the 3.5-rc5 release.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk/rYS0ACgkQMUfUDdst+ynuGQCfYYD43H+BtubcS+jt5N61/5lM
wUgAoM1wru64Kfox9v6U8g21AnLeJOhJ
=e1xG
-----END PGP SIGNATURE-----
Merge tag 'usb-3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are some small USB gadget bugfixes, and a few new USB device ids
added to some drivers for the 3.5-rc5 release.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: CP210x Add 10 Device IDs
USB: option: Add USB ID for Novatel Ovation MC551
usb: phy: Fix Kconfig dependency for Phy drivers
usb-storage: revert commit afff07e61a (Add 090c:1000 to unusal-devs)
SCSI & usb-storage: add try_rc_10_first flag
usb: musb: host: release dma channels if no active io
usb: gadget: lpc32xx_udc: fix build error with debugfs enabled
usb: otg: twl6030-usb: Fix twl writes
USB: option: add id for Cellient MEN-200
usb: dwc3: fix giveback of queued request in ep_dequeue
usb: gadget: Complete fsl qe/udc driver conversion
- omap_hsmmc: Using AUTO_CMD12 (enabled by default in 3.5-rc1) has
been found to cause data corruption on the BeagleBoard, but no
other OMAP boards so far. Revert the patch until there's a root
cause explanation that makes sense, at which point we might
decide to use a blacklist or whitelist.
- mmc_block: Fix incorrect data timeouts for the case of multiblock
(ACMD22) writes for block-addressed cards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=fRAN
-----END PGP SIGNATURE-----
Merge tag 'mmc-fixes-for-3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC fixes from Chris Ball:
- omap_hsmmc: Using AUTO_CMD12 (enabled by default in 3.5-rc1) has
been found to cause data corruption on the BeagleBoard, but no
other OMAP boards so far. Revert the patch until there's a root
cause explanation that makes sense, at which point we might
decide to use a blacklist or whitelist.
- mmc_block: Fix incorrect data timeouts for the case of multiblock
(ACMD22) writes for block-addressed cards.
* tag 'mmc-fixes-for-3.5-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
Revert "mmc: omap_hsmmc: Enable Auto CMD12"
mmc: block: fix the data timeout issue with ACMD22
regression fixups. Two NULL pointer dereferences were in the common clk
core due to lack of sanity checking and the third NPD was in the
mxs-specific clock code due to incorrect use of __initdata. The device
regressions were the result of improper data: a wrong string name for
matching DT data broke the SPEAr ethernet controller and another string
matching problem in the mxs clock data resulted in a broken MMC
controller.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJP6kiMAAoJEDqPOy9afJhJxZUQAMIH3oeMv98UJLVoaB3OECsz
l+H6UJs7kS0jdQeWyKT3peMxoulc2u3jWHVcTs7Cifb2RtLDNad1eR/vlMhD9ZKR
DxZwBaXJlg0cOVCmJL5T/urLpCXOToUdYXJShAJp9/2U7qYX2kAzaq1s+kDvAGp4
AcbcWOFR7O3BHc79gtZPvx2C3x1I4NShZhBeAZ6chRFJXl+SkXK5qtQkdQZt5rzX
L2LsifXcwsegbeoRrB8lJlRFev0Edxz/MTkmCfYCKJmm4Uj0vrUGXPiW4DPlyUSI
CS4Ghmm/lU4fNCi+PU/1rgoAbwgS/OUSQn7Q47Y28cizgeOPQKWuvuw0UPAOqS+U
GpmzIQWzQkxGbldenRTrUscQAwdjhGY8Rb89i/5HRvB6nv7jc2oylTih1FQ6B/cS
+ezEwoQjfeH8w7EzR1zNTKdlv3ysRa+rIl54wRgC05XOHmbKtYlQUw0jyBQNINcF
B1zy4Q90JKv1peW7foevJH34PbsnmA0IN2W6qxQw819MXSmT66a+b9rOI7mYKngo
z6LeY8qy1/77SklXv8gsP0dA0Nd2oEMvKH+ywur0PiMiegT49s6yviN6TZBN5YXp
xe0Ia8JshQ4qbSz61Da4lzd3/zzCKMxLm2Ak8Gr5l6givzxeJUONNu7EaWk3sGtM
H4dYsJsVtwXncyMmOBw/
=bFwf
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux
Pull clk common framework fixes from Mike Turquette:
"This contains three NULL pointer fixes and two device regression
fixups.
Two NULL pointer dereferences were in the common clk core due to lack
of sanity checking and the third NPD was in the mxs-specific clock
code due to incorrect use of __initdata.
The device regressions were the result of improper data: a wrong
string name for matching DT data broke the SPEAr ethernet controller
and another string matching problem in the mxs clock data resulted in
a broken MMC controller."
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux:
clk: mxs: fix clock lookup after freeing init memory
clk: mxs: fix ref_io clock definition
clk: Check parent for NULL in clk_change_rate
clk: Allow late cache allocation for clk->parents
clk: SPEAr600: Fix ethernet clock name for DT based probing
Daniel writes:
"Two tiny patches and one revert:
- Kill a bogus error message introduced in 3.4, further Bspec reading
indicates that this is how the hw is supposed to work.
- Reorder one backlight register restore, fixing broken backlight on some
machines after resume.
- Revert a hack from Jesse for ivb backlight control - it breaks the
backlight controls on my shiny new ivb laptop."
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
Revert "drm/i915: allow PCH PWM override on IVB"
drm/i915: Fix eDP blank screen after S3 resume on HP desktops
drm/i915: rip out the PM_IIR WARN
Commit 3a2923e83c introduced a bug when a corrupt descriptor
is encountered - although the following descriptor is discarded
and returned to the queue for reuse the associated frame is
also returned for processing. This leads to a panic:
BUG: unable to handle kernel NULL pointer dereference at 000000000000003a
IP: [<ffffffffa02599a5>] ath_rx_tasklet+0x165/0x1b00 [ath9k]
Call Trace:
<IRQ>
[<ffffffff812d7fa0>] ? map_single+0x60/0x60
[<ffffffffa028f044>] ? ath9k_ioread32+0x34/0x90 [ath9k]
[<ffffffffa0292eec>] athk9k_tasklet+0xdc/0x160 [ath9k]
[<ffffffff8105e133>] tasklet_action+0x63/0xd0
[<ffffffff8105dbc0>] __do_softirq+0xc0/0x1e0
[<ffffffff8101a873>] ? native_sched_clock+0x13/0x80
[<ffffffff815f9d5c>] call_softirq+0x1c/0x30
[<ffffffff810151f5>] do_softirq+0x75/0xb0
[<ffffffff8105df95>] irq_exit+0xb5/0xc0
[<ffffffff815fa5b3>] do_IRQ+0x63/0xe0
[<ffffffff815f0cea>] common_interrupt+0x6a/0x6a
<EOI>
[<ffffffff8131840a>] ? intel_idle+0xea/0x150
[<ffffffff813183eb>] ? intel_idle+0xcb/0x150
[<ffffffff814a1db9>] cpuidle_enter+0x19/0x20
[<ffffffff814a23d9>] cpuidle_idle_call+0xa9/0x240
[<ffffffff8101c4bf>] cpu_idle+0xaf/0x120
[<ffffffff815cda8e>] rest_init+0x72/0x74
[<ffffffff81cf4c1a>] start_kernel+0x3b7/0x3c4
[<ffffffff81cf4662>] ? repair_env_string+0x5e/0x5e
[<ffffffff81cf4346>] x86_64_start_reservations+0x131/0x135
[<ffffffff81cf444a>] x86_64_start_kernel+0x100/0x10f
Making sure bf is cleared to NULL in this case restores the
old behaviour.
Signed-off-by: Tom Hughes <tom@compton.nu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The latest Realtek driver for the RTL8188CU and RTL8192CU chips adds three
new USB IDs.
Reported-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit f82cfb6bcd.
This breaks the backlight controls on my IVB asus zenbook with an eDP
panel.
I guess the right fix would be to read this bit and use either the pch
or the cpu register to frob the backlight values. But that is stuff
for -next.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Commit e978aa7d7d ( cpuidle: Move
dev->last_residency update to driver enter routine; remove dev->last_state)
was breaking suspend on laptops, as reported in the below link
- https://lkml.org/lkml/2011/11/11/164
This was fixed in commit 3439a8da16
(ACPI / cpuidle: Remove acpi_idle_suspend (to fix suspend regression)
by removing acpi_idle_suspend flag.
- https://lkml.org/lkml/2011/11/14/74
But this did fix did not work on all systems
as Suspend/resume regression was reported on Lenovo S10-3
recently by Dave.
- https://lkml.org/lkml/2012/5/27/115
It looked like with commit e978aa7d broke suspend and
with commit 3439a8da resume was not working with acpi_idle driver.
This patch fixes the regression that caused this issue
in the first place. acpi_idle_suspend flag is essential on
some x86 systems to prevent the cpus from going to deeper C-states
when suspend is triggered ( commit b04e7bdb98 )
So reverting the commit 3439a8da is essential.
By default, irqs are disabled in cpu_idle arch specific call
and re-enabled in idle state return path . During suspend,
the acpi_idle_suspend flag is set, which
prevents the cpus from going to deeper idle states,
it is essential to enabling the irqs in this return path too.
To address the suspend issue,
we were not re-enabling the interrupts while returning from
acpi_idle_enter_bm() routine if acpi_idle_suspend flag is set.
and this caused suspend failure.
In addition to the above, to improve the readability of the code,
return of -ENIVAL is replaced with -EBUSY in acpi_idle_suspend
return path. Implying that the system is currently busy when suspend
is in progress, which prevents the cpus from entering deeper C-states.
Reported-and-Tested-by: Dav Hansen <dave@linux.vnet.ibm.com>
Tested-by: Preeti Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Reviewed-by: Srivatsa S Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Commit "e9b4cf2 UBI: fix debugfs-less systems support" fixed one
regression but introduced a different regression - the debugfs is now always
compiled out. Root cause: IS_ENABLED() arguments should be used with the
CONFIG_* prefix.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The freescale arm i.MX series platform can support this driver, and
usually the arm cpu works in the little endian mode by default, while
device tree entry value is stored in big endian format, we should use
be32_to_cpup() to handle them, after modification, it can work well
both on the le cpu and be cpu.
Cc: stable <stable@vger.kernel.org> # v3.2+
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
On some architectures address spaces are set up in a way that this is
not necessary to work properly but on some others (like s390) it is.
Make sure we operate on the user address space to allow copy_xxx_user()
from the vhost_worker() thread by setting it explicitly before calling
use_mm() and revert it after unuse_mm().
Signed-off-by: Jens Freimann <jfrei@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems that currently GPIO module is not working correctly during idle
when debounce is enabled - the system almost never responds to button
presses (observed on OMAP3530 ES2.1 and OMAP3630 ES1.2 pandora boards).
Even though wakeups are probably working, it seems that the GPIO module
itself is unable to detect input events and generate interrupts.
OMAP35x TRM also states that:
"If the debounce clock is inactive, the debounce cell gates all
input signals and thus cannot be used."
So whenever we are disabling debounce clocks (for PM or other reasons),
be sure the module's debounce feature is disabled too.
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
FCoE target mode was experiencing issues due to the fact that we were
sending up data frames that were padded to 60 bytes after the DDP logic had
already stripped the frame down to 52 or 56 depending on the use of VLANs.
This was resulting in the FCoE DDP logic having issues since it thought the
frame still had data in it due to the padding.
To resolve this, adding code so that we do not pad FCoE frames prior to
handling them to the stack.
CC: <stable@vger.kernel.org>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds 10 device IDs for CP210x based devices from the following manufacturers:
Timewave
Clipsal
Festo
Link Instruments
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device is also known as the Verizon USB551L.
Signed-off-by: Forest Bond <forest.bond@rapidrollout.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB phy layer driver are only built if usb host is selected, but they
are used too by USB_GADGET drivers
Signed-off-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch reverts the commit dba3c29ea4.
After bisecting, this commit dba3c29 is found to ruin micro-SD card data
(writing incorrect file, or fs is corrupt after several times mount)
on the beagle-xm revB, and reverting the commit will fix the problem.
Also from TRM of OMAP3/OMAP4/DM37x, the below is mentioned about
the Auto CMD12 Enable bit.
- SDIO does not support this feature.
- SD card only.
Looks it is not suitable to always enable Auto CMD12 in host controller
driver.
Considered that the commit is not mature enough, so ask to revert it
first.
Cc: Balaji T K <balajitk@ti.com>
Cc: Venkatraman S <svenkatr@ti.com>
Buglink: https://lkml.org/lkml/2012/6/10/225
Reported-by: Paolo Pisati <p.pisati@gmail.com>
Reported-bisected-and-tested-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
If multi block write operation fails for SD card, during
error handling we send the SD_APP_SEND_NUM_WR_BLKS (ACMD22)
to know how many blocks were already programmed by card.
But mmc_sd_num_wr_blocks() function which sends the ACMD22
calculates the data timeout value from csd.tacc_ns and
csd.tacc_clks parameters which will be 0 for block addressed
(>2GB cards) SD card. This would result in timeout_ns and
timeout_clks being 0 in the mmc_request passed to host driver.
This means host controller would program its data timeout timer
value with 0 which could result in DATA TIMEOUT errors from
controller.
To fix this issue, mmc_sd_num_wr_blocks() should instead
just call the mmc_set_data_timeout() to calculate the
data timeout value. mmc_set_data_timeout() function
ensures that non zero timeout value is set even for
block addressed SD cards.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Pull drm fixes from Dave Airlie:
"Just two changes: one udl endian fix, one nouveau memory corruption on
some GPUs."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau/fbcon: using nv_two_heads is not a good idea
drm/udl: Make sure to get correct endian keys from vendor descriptor
Pull HID fixes from Jiri Kosina:
"The most important one is a purification of Kconfig for CONFIG_HID;
the inclusion of HID groups and autoloading didn't leave the Kconfig
in a really consistent state. Henrik's patch fixes that. In addition
to that, there are two small fixes for logitech and magicmouse
drivers."
* 'upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: Fix the generic Kconfig options
HID: magicmouse: Correct report range of major / minor axes
HID: logitech: don't use stack based dj_report structures
nv_two_heads() was never meant to be used outside of pre-nv50 code. The
code checks for >= NV_10 for 2 CRTCs, then downgrades a few specific
chipsets to 1 CRTC based on (pci_device & 0x0ff0).
The breakage example seen is on GTX 560Ti, with a pciid of 0x1200, which
gets detected as an NV20 (0x020x) with 1 CRTC by nv_two_heads(), causing
memory corruption because there's actually 2 CRTCs..
This switches fbcon to use the CRTC count directly from the mode_config
structure, which will also fix the same issue on Kepler boards which have
4 CRTCs.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The struct clk_lookup are marked as __initdata, resulting in being
removed from memory after the kernel finished booting. However this
leads to a NULL pointer de-ref if loading a module which uses clk_get.
This patch removes the __initdata from the struct clk_lookup.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The definition of clocks ref_io0 and ref_io1 were inverted. It causes
a mmc regression on some boards right away. Fix the regression by
correcting the ref_io clock definition.
Reported-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
