Byte accesses for I/O devices in Xilinx IP is going to be less
desired in the future such that the driver is being changed to
use 32 bit accesses.
This change facilitates using the uartlite IP over a PCIe bus
which only allows 32 bit accesses.
Signed-off-by: John Linn <john.linn@xilinx.com>
Tested-by: Michal Simek <monstr@monstr.eu>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
n_gsm uses skb functions, so it should depend on NET.
n_gsm.c:(.text+0x123d49): undefined reference to `skb_dequeue'
n_gsm.c:(.text+0x123d98): undefined reference to `kfree_skb'
n_gsm.c:(.text+0x123e1e): undefined reference to `skb_pull'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add an implementation of GSM 0710 MUX. The implementation currently supports
- Basic and advanced framing (as either end of the link)
- UI or UIH data frames
- Adaption layer 1-4 (1 and 2 via tty, 3 and 4 as skbuff lists)
- Modem and control messages including the correct retry process
- Flow control
and exposes the MUX channels as a set of virtual tty devices including modem
signals. This is an experimental driver.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Push the max ldiscs by a few number to allow ldiscs
to exist in the staging directory and elsewhere.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The BF54xM procs imply the related BF54x define, so no need to check both.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that the SPORT MMR defines have been unified, switch over to it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rather than always turn on the SPORT TX interrupt, only do it when we've
actually queued up data for transmission. This avoids useless interrupt
processing.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These were all copied over from the Blackfin UART driver, but they don't
make sense here because these bits are all specific to the Blackfin UART.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Need to initialize the SPORT state rather than using random memory.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Common serial API says we need to grab the port lock before modifying
the port state to prevent inconsistent state between threads.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some people need flow control on their ports, so now boards can support
that via any GPIOs.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Clarifies command line set up for devices between consoles and early
devices.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The driver doesn't care about this, but the common serial core wants it.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
All the resources are in the boards files now.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The waiting loop to stop SPORT TX from TX interrupt is too long. This may
block the SPORT RX interrupts and cause the RX FIFO to overflow. So, do
stop sport TX only after the last char in TX FIFO is moved into the shift
register.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We cannot let a 32-bit RX FIFO read be interrupted otherwise a fake RX
underflow error might be generated.
URL: http://blackfin.uclinux.org/gf/tracker/5145
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2: (23 commits)
nilfs2: disallow remount of snapshot from/to a regular mount
nilfs2: use huge_encode_dev/huge_decode_dev
nilfs2: update comment on deactivate_super at nilfs_get_sb
nilfs2: replace MS_VERBOSE with MS_SILENT
nilfs2: add missing initialization of s_mode
nilfs2: fix misuse of open_bdev_exclusive/close_bdev_exclusive
nilfs2: enlarge s_volume_name member in nilfs_super_block
nilfs2: use checkpoint number instead of timestamp to select super block
nilfs2: add missing endian conversion on super block magic number
nilfs2: make nilfs_sc_*_ops static
nilfs2: add kernel doc comments to persistent object allocator functions
nilfs2: change sc_timer from a pointer to an embedded one in struct nilfs_sc_info
nilfs2: remove nilfs_segctor_init() in segment.c
nilfs2: insert checkpoint number in segment summary header
nilfs2: add a print message after loading nilfs2
nilfs2: cleanup multi kmem_cache_{create,destroy} code
nilfs2: move out checksum routines to segment buffer code
nilfs2: move pointer to super root block into logs
nilfs2: change default of 'errors' mount option to 'remount-ro' mode
nilfs2: Combine nilfs_btree_release_path() and nilfs_btree_free_path()
...
* git://git.infradead.org/mtd-2.6: (154 commits)
mtd: cfi_cmdset_0002: use AMD standard command-set with Winbond flash chips
mtd: cfi_cmdset_0002: Fix MODULE_ALIAS and linkage for new 0701 commandset ID
mtd: mxc_nand: Remove duplicate NAND_CMD_RESET case value
mtd: update gfp/slab.h includes
jffs2: Stop triggering block erases from jffs2_write_super()
jffs2: Rename jffs2_erase_pending_trigger() to jffs2_dirty_trigger()
jffs2: Use jffs2_garbage_collect_trigger() to trigger pending erases
jffs2: Require jffs2_garbage_collect_trigger() to be called with lock held
jffs2: Wake GC thread when there are blocks to be erased
jffs2: Erase pending blocks in GC pass, avoid invalid -EIO return
jffs2: Add 'work_done' return value from jffs2_erase_pending_blocks()
mtd: mtdchar: Do not corrupt backing device of device node inode
mtd/maps/pcmciamtd: Fix printk format for ssize_t in debug messages
drivers/mtd: Use kmemdup
mtd: cfi_cmdset_0002: Fix argument order in bootloc warning
mtd: nand: add Toshiba TC58NVG0 device ID
pcmciamtd: add another ID
pcmciamtd: coding style cleanups
pcmciamtd: fixing obvious errors
mtd: chips: add SST39WF160x NOR-flashes
...
Trivial conflicts due to dev_node removal in drivers/mtd/maps/pcmciamtd.c
* 'linux-next' of git://git.infradead.org/ubi-2.6:
UBI: misc comment fixes
UBI: fix s/then/than/ typos
UBI: init even if MTD device cannot be attached, if built into kernel
UBI: remove reboot notifier
* 'for-linus' of git://oss.sgi.com/xfs/xfs: (54 commits)
xfs: mark xfs_iomap_write_ helpers static
xfs: clean up end index calculation in xfs_page_state_convert
xfs: clean up mapping size calculation in __xfs_get_blocks
xfs: clean up xfs_iomap_valid
xfs: move I/O type flags into xfs_aops.c
xfs: kill struct xfs_iomap
xfs: report iomap_bn in block base
xfs: report iomap_offset and iomap_bsize in block base
xfs: remove iomap_delta
xfs: remove iomap_target
xfs: limit xfs_imap_to_bmap to a single mapping
xfs: simplify buffer to transaction matching
xfs: Make fiemap work in query mode.
xfs: kill off l_sectbb_mask
xfs: record log sector size rather than log2(that)
xfs: remove dead XFS_LOUD_RECOVERY code
xfs: removed unused XFS_QMOPT_ flags
xfs: remove a few macro indirections in the quota code
xfs: access quotainfo structure directly
xfs: wait for direct I/O to complete in fsync and write_inode
...
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2: (47 commits)
ocfs2: Silence a gcc warning.
ocfs2: Don't retry xattr set in case value extension fails.
ocfs2:dlm: avoid dlm->ast_lock lockres->spinlock dependency break
ocfs2: Reset xattr value size after xa_cleanup_value_truncate().
fs/ocfs2/dlm: Use kstrdup
fs/ocfs2/dlm: Drop memory allocation cast
Ocfs2: Optimize punching-hole code.
Ocfs2: Make ocfs2_find_cpos_for_left_leaf() public.
Ocfs2: Fix hole punching to correctly do CoW during cluster zeroing.
Ocfs2: Optimize ocfs2 truncate to use ocfs2_remove_btree_range() instead.
ocfs2: Block signals for mkdir/link/symlink/O_CREAT.
ocfs2: Wrap signal blocking in void functions.
ocfs2/dlm: Increase o2dlm lockres hash size
ocfs2: Make ocfs2_extend_trans() really extend.
ocfs2/trivial: Code cleanup for allocation reservation.
ocfs2: make ocfs2_adjust_resv_from_alloc simple.
ocfs2: Make nointr a default mount option
ocfs2/dlm: Make o2dlm domain join/leave messages KERN_NOTICE
o2net: log socket state changes
ocfs2: print node # when tcp fails
...
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (182 commits)
[SCSI] aacraid: add an ifdef'd device delete case instead of taking the device offline
[SCSI] aacraid: prohibit access to array container space
[SCSI] aacraid: add support for handling ATA pass-through commands.
[SCSI] aacraid: expose physical devices for models with newer firmware
[SCSI] aacraid: respond automatically to volumes added by config tool
[SCSI] fcoe: fix fcoe module ref counting
[SCSI] libfcoe: FIP Keep-Alive messages for VPorts are sent with incorrect port_id and wwn
[SCSI] libfcoe: Fix incorrect MAC address clearing
[SCSI] fcoe: fix a circular locking issue with rtnl and sysfs mutex
[SCSI] libfc: Move the port_id into lport
[SCSI] fcoe: move link speed checking into its own routine
[SCSI] libfc: Remove extra pointer check
[SCSI] libfc: Remove unused fc_get_host_port_type
[SCSI] fcoe: fixes wrong error exit in fcoe_create
[SCSI] libfc: set seq_id for incoming sequence
[SCSI] qla2xxx: Updates to ISP82xx support.
[SCSI] qla2xxx: Optionally disable target reset.
[SCSI] qla2xxx: ensure flash operation and host reset via sg_reset are mutually exclusive
[SCSI] qla2xxx: Silence bogus warning by gcc for wrap and did.
[SCSI] qla2xxx: T10 DIF support added.
...
The whole point of making some of the drivers automatically selected
unless 'EMBEDDED' was to handle quirks transparently after their separation
from the generic core.
Over time, some of the later-added quirks grew into more standalone drivers,
implementing non-trivial features a being larger than a few bytes of code.
In addition to that, some of the standalone drivers don't make sense for
99.9% of the users, as they are very specific to rare devices.
Therefore build by default in only those drivers which
- we historically used to support even before quirk separation from the
core code
- are isolated enough and likely to hit quite large portion of the
users anyway (Microsoft, Logitech)
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This is needed before the USB merge.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits)
qlcnic: adding co maintainer
ixgbe: add support for active DA cables
ixgbe: dcb, do not tag tc_prio_control frames
ixgbe: fix ixgbe_tx_is_paused logic
ixgbe: always enable vlan strip/insert when DCB is enabled
ixgbe: remove some redundant code in setting FCoE FIP filter
ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp
ixgbe: fix header len when unsplit packet overflows to data buffer
ipv6: Never schedule DAD timer on dead address
ipv6: Use POSTDAD state
ipv6: Use state_lock to protect ifa state
ipv6: Replace inet6_ifaddr->dead with state
cxgb4: notify upper drivers if the device is already up when they load
cxgb4: keep interrupts available when the ports are brought down
cxgb4: fix initial addition of MAC address
cnic: Return SPQ credit to bnx2x after ring setup and shutdown.
cnic: Convert cnic_local_flags to atomic ops.
can: Fix SJA1000 command register writes on SMP systems
bridge: fix build for CONFIG_SYSFS disabled
ARCNET: Limit com20020 PCI ID matches for SOHARD cards
...
Fix up various conflicts with pcmcia tree drivers/net/
{pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and
wireless/orinoco/spectrum_cs.c} and feature removal
(Documentation/feature-removal-schedule.txt).
Also fix a non-content conflict due to pm_qos_requirement getting
renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c
It is highly desirable to trap into kdb on panic. The debug core will
attempt to register as the first in line for the panic notifier.
CC: Ingo Molnar <mingo@elte.hu>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Certain calls from the kdb shell will call out to printk(), and any of
these calls should get vectored back to the kdb_printf() so that the
kdb pager and processing can be used, as well as to properly channel
I/O to the polled I/O devices.
CC: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
If kdb is open on a serial port that is not actually a console make
sure to call the poll routines to emit and receive characters.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Martin Hicks <mort@sgi.com>
Some kgdb I/O modules require the ability to create a breakpoint
tasklet, such as kgdboc and external modules such as kgdboe. The
breakpoint tasklet is used as an asynchronous entry point into the
debugger which will have a different function scope than the current
execution path where it might not be safe to have an inline
breakpoint. This is true of some of the kgdb I/O drivers which share
code with kgdb and rest of the kernel users.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
The only way the debugger can handle a trap in inside rcu_lock,
notify_die, or atomic_notifier_call_chain without a recursive fault is
to have a low level "first opportunity handler" do_trap_or_bp() handler.
Generally this will be something the vast majority of folks will not
need, but for those who need it, it is added as a kernel .config
option called KGDB_LOW_LEVEL_TRAP.
Also added was a die notification for oops such that kdb can catch an
oops for analysis.
There appeared to be no obvious way to pass the struct pt_regs from
the original exception back to the stack back tracer, so a special
case was added to show_stack() for when kdb is active because you
generally desire to generally look at the back trace of the original
exception.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
The only way the debugger can handle a trap in inside rcu_lock,
notify_die, or atomic_notifier_call_chain without a recursive fault is
to allow the kernel debugger to handle the exception first in
program_check_exception().
The other change here is to make sure that kgdb_handle_exception() is
called with correct parameters when catching an oops, because kdb
needs to know if the entry was an oops, single step, or breakpoint
exception.
[benh@kernel.crashing.org: move debugger_bpt instead of #ifdef]
CC: Paul Mackerras <paulus@samba.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The only way the debugger can handle a trap in inside rcu_lock,
notify_die, or atomic_notifier_call_chain without a triple fault is
to have a low level "first opportunity handler" in the int3 exception
handler.
Generally this will be something the vast majority of folks will not
need, but for those who need it, it is added as a kernel .config
option called KGDB_LOW_LEVEL_TRAP.
CC: Ingo Molnar <mingo@elte.hu>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: H. Peter Anvin <hpa@zytor.com>
CC: x86@kernel.org
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Remove all the references to the kgdb_post_primary_code. This
function serves no useful purpose because you can obtain the same
information from the "struct kgdb_state *ks" from with in the
debugger, if for some reason you want the data.
Also remove the unintentional duplicate assignment for ks->ex_vector.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Update the kgdb docs to reflect the new directory structure and API.
Merge in the kdb shell information.
[Randy Dunlap <rdunlap@xenotime.net>: grammatical corrections]
CC: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
This patch adds in the kdb PS/2 keyboard driver. This was mostly a
direct port from the original kdb where I cleaned up the code against
checkpatch.pl and added the glue to stitch it into kgdb.
This patch also enables early kdb debug via kgdbwait and the keyboard.
All the access to configure kdb using either a serial console or the
keyboard is done via kgdboc.
If you want to use only the keyboard and want to break in early you
would add to your kernel command arguments:
kgdboc=kbd kgdbwait
If you wanted serial and or the keyboard access you could use:
kgdboc=kbd,ttyS0
You can also configure kgdboc as a kernel module or at run time with
the sysfs where you can activate and deactivate kgdb.
Turn it on:
echo kbd,ttyS0 > /sys/module/kgdboc/parameters/kgdboc
Turn it off:
echo "" > /sys/module/kgdboc/parameters/kgdboc
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
One of the driving forces behind integrating another front end (kdb)
to the debug core is to allow front end commands to be accessible via
gdb's monitor command. It is true that you could write gdb macros to
get certain data, but you may want to just use gdb to access the
commands that are available in the kdb front end.
This patch implements the Rcmd gdb stub packet. In gdb you access
this with the "monitor" command. For instance you could type "monitor
help", "monitor lsmod" or "monitor ps A" etc...
There is no error checking or command restrictions on what you can and
cannot access at this point. Doing something like trying to set
breakpoints with the monitor command is going to cause nothing but
problems. Perhaps in the future only the commands that are actually
known to work with the gdb monitor command will be available.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Allow kgdboc to work on sparc hardware with the Zilog serial chips.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: David S. Miller <davem@davemloft.net>
The sci_poll_get_char() needs to return immediately if there is no
input from the chip to process, and must return a value of
NO_POLL_CHAR.
This allows kgdboc to process multiple polled devices while kgdb is
active.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
The design of the kdb shell requires that every device that can
provide input to kdb have a polling routine that exits immediately if
there is no character available. This is required in order to get the
page scrolling mechanism working.
Changing the kernel debugger I/O API to require all polling character
routines to exit immediately if there is no data allows the kernel
debugger to process multiple input channels.
NO_POLL_CHAR will be the return code to the polling routine when ever
there is no character available.
CC: linux-serial@vger.kernel.org
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
These are the minimum changes to the kgdb core in order to enable an
API to connect a new front end (kdb) to the debug core.
This patch introduces the dbg_kdb_mode variable controls where the
user level I/O is routed. It will be routed to the gdbstub (kgdb) or
to the kdb front end which is a simple shell available over the kgdboc
connection.
You can switch back and forth between kdb or the gdb stub mode of
operation dynamically. From gdb stub mode you can blindly type
"$3#33", or from the kdb mode you can enter "kgdb" to switch to the
gdb stub.
The logic in the debug core depends on kdb to look for the typical gdb
connection sequences and return immediately with KGDB_PASS_EVENT if a
gdb serial command sequence is detected. That should allow a
reasonably seamless transition between kdb -> gdb without leaving the
kernel exception state. The two gdb serial queries that kdb is
responsible for detecting are the "?" and "qSupported" packets.
CC: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Martin Hicks <mort@sgi.com>
This patch contains the hooks and instrumentation into kernel which
live outside the kernel/debug directory, which the kdb core
will call to run commands like lsmod, dmesg, bt etc...
CC: linux-arch@vger.kernel.org
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Martin Hicks <mort@sgi.com>
This patch contains only the kdb core. Because the change set was
large, it was split. The next patch in the series includes the
instrumentation into the core kernel which are mainly helper functions
for kdb.
This work is directly derived from kdb v4.4 found at:
ftp://oss.sgi.com/projects/kdb/download/v4.4/
The kdb internals have been re-organized to make them mostly platform
independent and to connect everything to the debug core which is used by
gdbstub (which has long been known as kgdb).
The original version of kdb was 58,000 lines worth of changes to
support x86. From that implementation only the kdb shell, and basic
commands for memory access, runcontrol, lsmod, and dmesg where carried
forward.
This is a generic implementation which aims to cover all the current
architectures using the kgdb core: ppc, arm, x86, mips, sparc, sh and
blackfin. More archictectures can be added by implementing the
architecture specific kgdb functions.
[mort@sgi.com: Compile fix with hugepages enabled]
[mort@sgi.com: Clean breakpoint code renaming kdba_ -> kdb_]
[mort@sgi.com: fix new line after printing registers]
[mort@sgi.com: Remove the concept of global vs. local breakpoints]
[mort@sgi.com: Rework kdb_si_swapinfo to use more generic name]
[mort@sgi.com: fix the information dump macros, remove 'arch' from the names]
[sfr@canb.auug.org.au: include fixup to include linux/slab.h]
CC: linux-arch@vger.kernel.org
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Martin Hicks <mort@sgi.com>
The new debug core api requires all architectures that use to debug
core to implement a function to set the program counter.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
