Florian Fainelli says:
====================
net: dsa: b53: Turn on Broadcom tags
This was long overdue, with this patch series, the b53 driver now
turns on Broadcom tags except for 5325 and 5365 which use an older
format that we do not support yet (TBD).
First patch is necessary in order for bgmac, used on BCM5301X and Northstar
Plus to work correctly and successfully send ARP packets back to the requsester.
Second patch is actually a bug fix, but because net/master and net-next/master
diverge in that area, I am targeting net-next/master here.
Finally, the last patch enables Broadcom tags after checking that the CPU port
selected is either, 5, 7 or 8, since those are the only valid combinations
given currently supported HW.
Changes in v3:
- guarded padding with netdev_uses_dsa() to let the non-DSA use cases
not have a performance hit for smaller packets
- added missing select NET_DSA_TAG_BRCM to drivers/net/dsa/b53/Kconfig
Changes in v2:
- moved a hunk between patch 2 and patch 3 to avoid a bisectability issue
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable Broadcom tags for b53 devices, except 5325 and 5365 which use a
different Broadcom tag format not yet supported by net/dsa/tag_brcm.c.
We also make sure that we can turn on Broadcom tags on a CPU port number
that is capable of that: 5, 7 or 8.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev->cpu_port is the driver local information that should only be used
to look up register offsets for a particular port, when they differ
(e.g: IMP port override), but it should certainly not be used in place
of the DSA configured CPU port.
Since the DSA switch layer calls port_vlan_{add,del}() on the CPU port
as well, we can remove the specific setting of the CPU port within
port_vlan_{add,del}.
Fixes: ff39c2d686 ("net: dsa: b53: Add bridge support")
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for enabling Broadcom tags with b53, pad packets to a
minimum size of 64 bytes (sans FCS) in order for the Broadcom switch to
accept ingressing frames. Without this, we would typically be able to
DHCP, but not resolve with ARP because packets are too small and get
rejected by the switch.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Egil Hjelmeland says:
====================
net: dsa: lan9303: IGMP handling
Set up the HW switch to trap IGMP packets to CPU port.
And make sure skb->offload_fwd_mark is cleared for incoming IGMP packets.
skb->offload_fwd_mark calculation is a candidate for consolidation into the
DSA core. The calculation can probably be more polished when done at a point
where DSA has updated skb.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that IGMP packets no longer is flooded in HW, we want the SW bridge to
forward packets based on bridge configuration. To make that happen,
IGMP packets must have skb->offload_fwd_mark = 0.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
IGMP packets should be trapped to the CPU port. The SW bridge knows
whether to forward to other ports.
With "IGMP snooping for local traffic" merged, IGMP trapping is also
required for stable IGMPv2 operation.
LAN9303 does not trap IGMP packets by default.
Enable IGMP trapping in lan9303_setup.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The statistics histogram mode was not being explicitly initialized on
devices other than the 6390 family. Clearing the statistics then
overwrote the default setting, setting the histogram to a reserved
mode.
Explicitly set the histogram mode for all devices. Change the
statistics clear into a read/modify/write, and since it is now more
complex, move it into global1.c.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn says:
====================
mv88e6xxx broadcast flooding in hardware
This patchset makes the mv88e6xxx driver perform flooding in hardware,
rather than let the software bridge perform the flooding. This is a
prerequisite for IGMP snooping on the bridge interface.
In order to make hardware broadcasting work, a few other issues need
fixing or improving. SWITCHDEV_ATTR_ID_PORT_PARENT_ID is broken, which
is apparent when testing on the ZII devel board with multiple
switches.
Some of these patches are taken from a previous RFC patchset of IGMP
support.
Rebased onto net-next, with fixup for Vivien's refactoring.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, the switch does not flood broadcast frames. Instead the
broadcast address is unknown in the ATU, so the frame gets forwarded
out the cpu port. The software bridge then floods it back to the
individual switch ports which are members of the bridge.
Add an ATU entry in the switch so that it floods broadcast frames out
ports, rather than have the software bridge do it. Also, send a copy
out the cpu port and any dsa ports. Rely on the port vectors to
prevent broadcast frames leaking between bridges, and separated ports.
Additionally, when a VLAN is added, a new FID is allocated. This
represents a new table of ATU entries. A broadcast entry is added to
the new FID.
With offload_fwd_mark being set, the software bridge will not flood
the frames it receives back to the switch.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is going to be needed by a soon to be added new
function. Move it earlier so we can avoid a forward declaration.
No functional changes.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When testing if a VLAN is one more than one bridge, we print an error
message that the VLAN is already in use somewhere else. Print both the
new port which would like the VLAN, and the port which already has it,
to aid debugging.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Having the same VLAN on multiple bridges is currently unsupported as
an offload. mv88e6xxx_port_check_hw_vlan() is used to ensure that a
VLAN is not on multiple bridges when adding a VLAN range to a port. It
loops the ports and checks to see if there are ports in a different
bridge with the same VLAN.
While walking all switch ports, the code was checking if the new port
has a netdev slave attached to it. If not, skip checking the port
being walked. This seems like a typ0. If the new port does not have a
slave, how has a VLAN been added to it in the first place, requiring
this check be performed at all? More likely, we should be checking if
the port being walked has a slave. Without the port having a slave, it
cannot have a VLAN on it, so there is no need to check further for
that particular port.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The software bridge needs to know if a packet has already been bridged
by hardware offload to ports in the same hardware offload, in order
that it does not re-flood them, causing duplicates. This is
particularly true for broadcast and multicast traffic which the host
has requested.
By setting offload_fwd_mark in the skb the bridge will only flood to
ports in other offloads and other netifs. Set this flag in the DSA and
EDSA tag driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
SWITCHDEV_ATTR_ID_PORT_PARENT_ID is used by the software bridge when
determining which ports to flood a packet out. If the packet
originated from a switch, it assumes the switch has already flooded
the packet out the switches ports, so the bridge should not flood the
packet itself out switch ports. Ports on the same switch are expected
to return the same parent ID when SWITCHDEV_ATTR_ID_PORT_PARENT_ID is
called.
DSA gets this wrong with clusters of switches. As far as the software
bridge is concerned, the cluster is all one switch. A packet from any
switch in the cluster can be assumed to have been flooded as needed
out of all ports of the cluster, not just the switch it originated
from. Hence all ports of a cluster should return the same parent. The
old implementation did not, each switch in the cluster had its own ID.
Also wrong was that the ID was not unique if multiple DSA instances
are in operation.
Use the tree ID as the parent ID, which is the same for all switches
in a cluster and unique across switch clusters.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Schmidt says:
====================
pull-request: net-next: ieee802154 2017-11-09
A small update on ieee802154 patches for net-next. Nothing dramatic, but simply
housekeeping this time around.
A fix for the correct mask to be applied in the mrf24j40 driver by Gustavo A. R. Silva
Removal of a non existing email user for the ca8210 driver by Harry Morris
A bunch of checkpatch cleanups across the subsystem from myself
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two different combined signal for various interrupt events:
In EQOS-CORE and EQOS-MTL configurations, mci_intr_o is the interrupt
signal.
In EQOS-DMA, EQOS-AHB and EQOS-AXI configurations, these interrupt events
are combined with the events in the DMA on the sbd_intr_o signal.
Depending on configuration, the device tree irq "macirq" will refer to
either mci_intr_o or sbd_intr_o.
The databook states:
"The MAC generates the LPI interrupt when the Tx or Rx side enters or exits
the LPI state. The interrupt mci_intr_o (sbd_intr_o in certain
configurations) is asserted when the LPI interrupt status is set.
When the MAC exits the Rx LPI state, then in addition to the mci_intr_o
(sbd_intr_o in certain configurations), the sideband signal lpi_intr_o is
asserted.
If you do not want to gate-off the application clock during the Rx LPI
state, you can leave the lpi_intr_o signal unconnected and use the
mci_intr_o (sbd_intr_o in certain configurations) signal to detect Rx LPI
exit."
Since the "macirq" is always raised when Tx or Rx enters/exits the LPI
state, "eth_lpi" must therefore refer to lpi_intr_o, which is only raised
when Rx exits the LPI state. Update the DT binding description to reflect
reality.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When process the outbound packet of ipv6, we should assign the master
device to output device other than input device.
Signed-off-by: Keefe Liu <liuqifa@huawei.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an error in memory allocation/freeing in
ThunderX PF driver.
I moved the allocation to the probe() function and made it managed.
>From the Colin's email:
While running static analysis on linux-next with CoverityScan I found 3
double free errors in the Cavium thunder driver.
The issue occurs on the err_disable_device: label of function nic_probe
when nic_free_lmacmem(nic) is called and a double free occurs on
nic->duplex, nic->link and nic->speed. This occurs when nic_init_hw()
fails:
/* Initialize hardware */
err = nic_init_hw(nic);
if (err)
goto err_release_regions;
nic_init_hw() calls nic_get_hw_info() and this calls nic_free_lmacmem()
if any of the allocations fail. This free'ing occurs again by the call
to nic_free_lmacmem() on the err_release_regions exit path in nic_probe().
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When Thunderbolt network interface is disabled or when the cable is
unplugged the driver releases all allocated buffers by calling
tbnet_free_buffers() for each ring. This function then calls
dma_unmap_page() for each buffer it finds where bus address is non-zero.
Now, we only clear this bus address when the Tx buffer is sent to the
hardware so it is possible that the function finds an entry that has
already been unmapped.
Enabling DMA-API debugging catches this as well:
thunderbolt 0000:06:00.0: DMA-API: device driver tries to free DMA
memory it has not allocated [device address=0x0000000068321000] [size=4096 bytes]
Fix this by clearing the bus address of a Tx frame right after we have
unmapped the buffer.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The per-cpu counter for init_net is prepared in core_initcall.
The patch 7d720c3e ("percpu: add __percpu sparse annotations to net")
and d6d9ca0fe ("net: this_cpu_xxx conversions") optimize the
routines. Then remove the old counter.
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Tonghao Zhang <zhangtonghao@didichuxing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable start is assigned but never read hence it is redundant
and can be removed. Cleans up clang warning:
drivers/net/ethernet/sfc/ptp.c:655:2: warning: Value stored to 'start'
is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The assignment to mbcp is identical to the initiatialized value assigned
to mbcp at declaration time a few lines earlier, hence we can remove the
second redundant assignment. Cleans up clang warning:
drivers/net/ethernet/qlogic/qlge/qlge_mpi.c:209:22: warning:
Value stored to 'mbcp' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114928
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114888
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114891
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 115106
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sessions are already removed by the proto ->destroy() handlers, and
since commit f3c66d4e14 ("l2tp: prevent creation of sessions on terminated tunnels"),
we're guaranteed that no new session can be created afterwards.
Furthermore, l2tp_tunnel_closeall() can sleep when there are sessions
left to close. So we really shouldn't call it in a ->sk_destruct()
handler, as it can be used from atomic context.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuchung Cheng says:
====================
remove FACK loss recovery
This patch set removes the forward-acknowledgment (FACK)
packet-based loss and reordering detection. This simplifies TCP
loss recovery since the SACK scoreboard no longer needs to track
the number of pending packets under highest SACKed sequence. FACK
is subsumed by the time-based RACK loss detection which is more
robust under reordering and second order losses.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the reordering distance measurement in packet unit with
sequence based approach. Previously it trackes the number of "packets"
toward the forward ACK (i.e. highest sacked sequence)in a state
variable "fackets_out".
Precisely measuring reordering degree on packet distance has not much
benefit, as the degree constantly changes by factors like path, load,
and congestion window. It is also complicated and prone to arcane bugs.
This patch replaces with sequence-based approach that's much simpler.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FACK loss detection has been disabled by default and the
successor RACK subsumed FACK and can handle reordering better.
This patch removes FACK to simplify TCP loss recovery.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1397960
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1397972
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the login buffer to include client data for the vnic driver,
this includes the OS name, LPAR name, and device name. This update
allows this information to be available in the VIOS.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lawrence Brakmo says:
====================
bpf: Fix bugs in sock_ops samples
The programs were returning -1 in some cases when they should
only return 0 or 1. Changes in the verifier now catch this
issue and the programs fail to load. This is now fixed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The program was returning -1 in some cases which is not allowed
by the verifier any longer.
Fixes: 390ee7e29f ("bpf: enforce return code for cgroup-bpf programs")
Signed-off-by: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The program was returning -1 in some cases which is not allowed
by the verifier any longer.
Fixes: 390ee7e29f ("bpf: enforce return code for cgroup-bpf programs")
Signed-off-by: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The program was returning -1 in some cases which is not allowed
by the verifier any longer.
Fixes: 390ee7e29f ("bpf: enforce return code for cgroup-bpf programs")
Signed-off-by: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The program was returning -1 in some cases which is not allowed
by the verifier any longer.
Fixes: 390ee7e29f ("bpf: enforce return code for cgroup-bpf programs")
Signed-off-by: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The program was returning -1 in some cases which is not allowed
by the verifier any longer.
Fixes: 390ee7e29f ("bpf: enforce return code for cgroup-bpf programs")
Signed-off-by: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The program was returning -1 in some cases which is not allowed
by the verifier any longer.
Fixes: 390ee7e29f ("bpf: enforce return code for cgroup-bpf programs")
Signed-off-by: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the TIPC RPS dissector is based only on the incoming packets'
source node address, hence steering all traffic from a node to the same
core. We have seen that this makes the links vulnerable to starvation
and unnecessary resets when we turn down the link tolerance to very low
values.
To reduce the risk of this happening, we exempt probe and probe replies
packets from the convergence to one core per source node. Instead, we do
the opposite, - we try to diverge those packets across as many cores as
possible, by randomizing the flow selector key.
To make such packets identifiable to the dissector, we add a new
'is_keepalive' bit to word 0 of the LINK_PROTOCOL header. This bit is
set both for PROBE and PROBE_REPLY messages, and only for those.
It should be noted that these packets are not part of any flow anyway,
and only constitute a minuscule fraction of all packets sent across a
link. Hence, there is no risk that this will affect overall performance.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Grzeschik says:
====================
net: macb: add error handling on probe and
This series adds more error handling to the macb driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We add the call of_node_put(bp->phy_node) to all associated error
paths for memory clean up.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We add the call of_phy_deregister_fixed_link to all associated
error paths for memory clean up.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GOP statistics from all ports of one instance of the driver are gathered
with one work recalled in loop in a workqueue. The loop is started when
a port is up, and stopped when a port is down. This last condition is
obviously wrong.
Fix this by having a work per port. This way, starting and stoping it
when the port is up or down will be fine, while minimizing unnecessary
CPU usage.
Fixes: 118d6298f6 ("net: mvpp2: add ethtool GOP statistics")
Reported-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lipeng says:
====================
net: hns3: Bug fixes & Code improvements in HNS3 driver
This patch-set introduces some bug fixes and code improvements.
As [patch 1/2] depends on the patch {5392902 net: hns3: Consistently using
GENMASK in hns3 driver}, which exists in net-next, not exists in net, so
push this serise to nex-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
