The uboot may run the QuadSpi controler with command:
#sf probe
So we should reset the module in the probe.
This patch also clear the pending interrupts which arised by the uboot
code.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
QSPI1 cannot wake up CCM from WAIT mode on SX ARD board, add pmqos to
let PM NOT enter WAIT mode when accessing QSPI1, refer to TKT245618.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Han Xu <Han.xu@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We found there is a low probability(5%) QSPI access timeout issue,
usually it happened on kernel boot stage, the first time kernel tried to
access QSPI chip. The READ_ID command was sent but not executed,
consequently the probe function failed.
The root cause is that the divider is not glitchless in i.MX6SX chip.
If qspi clock enabled then change clock frequency by call clk_set_rate,
there will be glitch at low possiblity rate and pass to qspi controller.
The controler will be hang by this glitch.
Based on the new clock flag(CLK_SET_RATE_GATE) and new framework, we
need to change the approach of seting clock rate.
1. Disable clock.
2. call clk_set_rate.
3. Enable clock again.
Signed-off-by: Han Xu <han.xu@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add i.mx6ul chip support
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Han xu <han.xu@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Support i.mx7d.
quadspi in i.mx7d increase rxfifo.
require fill at least 16byte to trigger data transfer.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Han Xu <han.xu@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
add several quirk to distinguish different version of qspi module.
Signed-off-by: Han Xu <han.xu@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
QSPI may failed to map enough memory (256MB) for AHB read in
previous implementation, especially in 3G/1G memory layout kernel.
Dynamically map memory to avoid such issue.
This implementation generally map QUADSPI_MAX_IOMAP (default 4MB) memory
for AHB read, it should be enough for common scenarios, and the side
effect (0.6% performance drop) is minor.
Previous implementation
root@imx6qdlsolo:~# dd if=/dev/mtd0 of=/dev/null bs=1K count=32K
32768+0 records in
32768+0 records out
33554432 bytes (34 MB) copied, 2.16006 s, 15.5 MB/s
root@imx6qdlsolo:~# dd if=/dev/mtd0 of=/dev/null bs=32M count=1
1+0 records in
1+0 records out
33554432 bytes (34 MB) copied, 1.43149 s, 23.4 MB/s
After applied the patch
root@imx6qdlsolo:~# dd if=/dev/mtd0 of=/dev/null bs=1K count=32K
32768+0 records in
32768+0 records out
33554432 bytes (34 MB) copied, 2.1743 s, 15.4 MB/s
root@imx6qdlsolo:~# dd if=/dev/mtd0 of=/dev/null bs=32M count=1
1+0 records in
1+0 records out
33554432 bytes (34 MB) copied, 1.43158 s, 23.4 MB/s
Signed-off-by: Han Xu <han.xu@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When we added the "jedec,spi-nor" compatible string for use in this
driver, we added it as a modalias option. The modalias can be derived in
different ways for platform devices vs. device tree (of_*) matching. But
for device tree matching (the primary target of this identifier string),
the modalias is determined from the first entry in the 'compatible'
property. IOW, the following properties would bind to this driver:
// Option (a), modalias = "spi-nor"
compatible = "jedec,spi-nor";
// Option (b), modalias = "spi-nor"
compatible = "idontknowwhatimdoing,spi-nor";
But the following would not:
// Option (c), modalias = "shinynewdevice"
compatible = "myvendor,shinynewdevice", "jedec,spi-nor";
So, we'd like to match (a) and (c) (even when we don't have an explicit
entry for "shinynewdevice"), and we'd rather not allow (b).
To do this, we
(1) always (for devices without specific platform data) pass the
modalias to the spi-nor library;
(2) rework the spi-nor library to not reject "bad" names, and
instead just fall back to autodetection; and
(3) add the .of_match_table to properly catch all "jedec,spi-nor".
This allows (a) and (c) without warnings, and rejects (b).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Replaces the hard coded "always use EDO" policy with that prescribed
by the ONFI 3.1 specification that EDO mode should always be used if tRC
is below 30ns.
Signed-off-by: Roy Spliet <r.spliet@ultimaker.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The TIMING_CFG register was previously statically set to a magic value
(extracted from Allwinner's BSP) when initializing the NAND controller.
Now that we have more details about the TIMING_CFG register layout
(extracted from the A83 user manual) we can dynamically calculate the
appropriate value for each NAND chip and set it when selecting the
chip.
Signed-off-by: Roy Spliet <r.spliet@ultimaker.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
QUADSPI_MCR_CLR_TXF_MASK is the correct mask for clearing the TX FIFO.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
r852_ecc_correct() reads a 32-bit register into a 16-bit variable,
ecc_reg, but this variable is later used as if it was larger. This is
reported by clang when building the kernel with many warnings:
drivers/mtd/nand/r852.c:512:11: error: shift count >= width of type
[-Werror,-Wshift-count-overflow]
ecc_reg >>= 16;
^ ~~
Fix this by making ecc_reg 32-bit, like the return type of
r852_read_reg_dword().
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
It is needed for k2l keystone2 EVM which uses NAND flash with 4K page
size, hence add support for 4K page size nand devices.
[Brian: similar work submitted by Murali Karicheri <m-karicheri2@ti.com>
and Hao Zhang <hzhang@ti.com>]
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Some drivers use it now, others just set the limits field manually.
But in preparation for splitting this into a hard and soft limit,
ensure that they all call the proper function for setting the hw
limit for discards.
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Do not call free_device() in init_nandsim, the caller - ns_init_module -
will take care of that if something goes wrong.
Signed-off-by: Sheng Yong <shengyong1@huawei.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
If allocating ns->nand_pages_slab fails, do not try to destroy it when
cleaning up nandsim resources.
Signed-off-by: Sheng Yong <shengyong1@huawei.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Main excitement here is Peter Zijlstra's lockless rbtree optimization to
speed module address lookup. He found some abusers of the module lock
doing that too.
A little bit of parameter work here too; including Dan Streetman's breaking
up the big param mutex so writing a parameter can load another module (yeah,
really). Unfortunately that broke the usual suspects, !CONFIG_MODULES and
!CONFIG_SYSFS, so those fixes were appended too.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tWPQ
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"Main excitement here is Peter Zijlstra's lockless rbtree optimization
to speed module address lookup. He found some abusers of the module
lock doing that too.
A little bit of parameter work here too; including Dan Streetman's
breaking up the big param mutex so writing a parameter can load
another module (yeah, really). Unfortunately that broke the usual
suspects, !CONFIG_MODULES and !CONFIG_SYSFS, so those fixes were
appended too"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (26 commits)
modules: only use mod->param_lock if CONFIG_MODULES
param: fix module param locks when !CONFIG_SYSFS.
rcu: merge fix for Convert ACCESS_ONCE() to READ_ONCE() and WRITE_ONCE()
module: add per-module param_lock
module: make perm const
params: suppress unused variable error, warn once just in case code changes.
modules: clarify CONFIG_MODULE_COMPRESS help, suggest 'N'.
kernel/module.c: avoid ifdefs for sig_enforce declaration
kernel/workqueue.c: remove ifdefs over wq_power_efficient
kernel/params.c: export param_ops_bool_enable_only
kernel/params.c: generalize bool_enable_only
kernel/module.c: use generic module param operaters for sig_enforce
kernel/params: constify struct kernel_param_ops uses
sysfs: tightened sysfs permission checks
module: Rework module_addr_{min,max}
module: Use __module_address() for module_address_lookup()
module: Make the mod_tree stuff conditional on PERF_EVENTS || TRACING
module: Optimize __module_address() using a latched RB-tree
rbtree: Implement generic latch_tree
seqlock: Introduce raw_read_seqcount_latch()
...
Pull cgroup writeback support from Jens Axboe:
"This is the big pull request for adding cgroup writeback support.
This code has been in development for a long time, and it has been
simmering in for-next for a good chunk of this cycle too. This is one
of those problems that has been talked about for at least half a
decade, finally there's a solution and code to go with it.
Also see last weeks writeup on LWN:
http://lwn.net/Articles/648292/"
* 'for-4.2/writeback' of git://git.kernel.dk/linux-block: (85 commits)
writeback, blkio: add documentation for cgroup writeback support
vfs, writeback: replace FS_CGROUP_WRITEBACK with SB_I_CGROUPWB
writeback: do foreign inode detection iff cgroup writeback is enabled
v9fs: fix error handling in v9fs_session_init()
bdi: fix wrong error return value in cgwb_create()
buffer: remove unusued 'ret' variable
writeback: disassociate inodes from dying bdi_writebacks
writeback: implement foreign cgroup inode bdi_writeback switching
writeback: add lockdep annotation to inode_to_wb()
writeback: use unlocked_inode_to_wb transaction in inode_congested()
writeback: implement unlocked_inode_to_wb transaction and use it for stat updates
writeback: implement [locked_]inode_to_wb_and_lock_list()
writeback: implement foreign cgroup inode detection
writeback: make writeback_control track the inode being written back
writeback: relocate wb[_try]_get(), wb_put(), inode_{attach|detach}_wb()
mm: vmscan: disable memcg direct reclaim stalling if cgroup writeback support is in use
writeback: implement memcg writeback domain based throttling
writeback: reset wb_domain->dirty_limit[_tstmp] when memcg domain size changes
writeback: implement memcg wb_domain
writeback: update wb_over_bg_thresh() to use wb_domain aware operations
...
* Minor fixes for UBI and UBIFS
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=xU0H
-----END PGP SIGNATURE-----
Merge tag 'upstream-4.2-rc1' of git://git.infradead.org/linux-ubifs
Pull UBI/UBIFS updates from Richard Weinberger:
"Minor fixes for UBI and UBIFS"
* tag 'upstream-4.2-rc1' of git://git.infradead.org/linux-ubifs:
UBI: Remove unnecessary `\'
UBI: Use static class and attribute groups
UBI: add a helper function for updatting on-flash layout volumes
UBI: Fastmap: Do not add vol if it already exists
UBI: Init vol->reserved_pebs by assignment
UBI: Fastmap: Rename variables to make them meaningful
UBI: Fastmap: Remove unnecessary `\'
UBI: Fastmap: Use max() to get the larger value
ubifs: fix to check error code of register_shrinker
UBI: block: Dynamically allocate minor numbers
- Disable the 32-bit vdso when building LE, so we can build with a 64-bit only
toolchain.
- EEH fixes from Gavin & Richard.
- Enable the sys_kcmp syscall from Laurent.
- Sysfs control for fastsleep workaround from Shreyas.
- Expose OPAL events as an irq chip by Alistair.
- MSI ops moved to pci_controller_ops by Daniel.
- Fix for kernel to userspace backtraces for perf from Anton.
- Merge pseries and pseries_le defconfigs from Cyril.
- CXL in-kernel API from Mikey.
- OPAL prd driver from Jeremy.
- Fix for DSCR handling & tests from Anshuman.
- Powernv flash mtd driver from Cyril.
- Dynamic DMA Window support on powernv from Alexey.
- LLVM clang fixes & workarounds from Anton.
- Reworked version of the patch to abort syscalls when transactional.
- Fix the swap encoding to support 4TB, from Aneesh.
- Various fixes as usual.
- Freescale updates from Scott: Highlights include more 8xx optimizations, an
e6500 hugetlb optimization, QMan device tree nodes, t1024/t1023 support, and
various fixes and cleanup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=d9Wh
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc updates from Michael Ellerman:
- disable the 32-bit vdso when building LE, so we can build with a
64-bit only toolchain.
- EEH fixes from Gavin & Richard.
- enable the sys_kcmp syscall from Laurent.
- sysfs control for fastsleep workaround from Shreyas.
- expose OPAL events as an irq chip by Alistair.
- MSI ops moved to pci_controller_ops by Daniel.
- fix for kernel to userspace backtraces for perf from Anton.
- merge pseries and pseries_le defconfigs from Cyril.
- CXL in-kernel API from Mikey.
- OPAL prd driver from Jeremy.
- fix for DSCR handling & tests from Anshuman.
- Powernv flash mtd driver from Cyril.
- dynamic DMA Window support on powernv from Alexey.
- LLVM clang fixes & workarounds from Anton.
- reworked version of the patch to abort syscalls when transactional.
- fix the swap encoding to support 4TB, from Aneesh.
- various fixes as usual.
- Freescale updates from Scott: Highlights include more 8xx
optimizations, an e6500 hugetlb optimization, QMan device tree nodes,
t1024/t1023 support, and various fixes and cleanup.
* tag 'powerpc-4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (180 commits)
cxl: Fix typo in debug print
cxl: Add CXL_KERNEL_API config option
powerpc/powernv: Fix wrong IOMMU table in pnv_ioda_setup_bus_dma()
powerpc/mm: Change the swap encoding in pte.
powerpc/mm: PTE_RPN_MAX is not used, remove the same
powerpc/tm: Abort syscalls in active transactions
powerpc/iommu/ioda2: Enable compile with IOV=on and IOMMU_API=off
powerpc/include: Add opal-prd to installed uapi headers
powerpc/powernv: fix construction of opal PRD messages
powerpc/powernv: Increase opal-irqchip initcall priority
powerpc: Make doorbell check preemption safe
powerpc/powernv: pnv_init_idle_states() should only run on powernv
macintosh/nvram: Remove as unused
powerpc: Don't use gcc specific options on clang
powerpc: Don't use -mno-strict-align on clang
powerpc: Only use -mtraceback=no, -mno-string and -msoft-float if toolchain supports it
powerpc: Only use -mabi=altivec if toolchain supports it
powerpc: Fix duplicate const clang warning in user access code
vfio: powerpc/spapr: Support Dynamic DMA windows
vfio: powerpc/spapr: Register memory and define IOMMU v2
...
Add supports for simultaneous access to multiple chips. Need to lock
the mutex before any quad spi operations and unlock the mutex after
operations complete.
Signed-off-by: Han Xu <b45815@freescale.com>
[Brian: reworked err path in fsl_qspi_prep()]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
kasprintf() does a dynamic memory allocation and can fail.
We have to handle that case.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
kasprintf() used in get_partition_name() does a dynamic
memory allocation and can fail. We have to handle that case.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
kasprintf() does a dynamic memory allocation and can fail.
We have to handle that case.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
device_create_file() can fail, therefore we have to
handle this case and abort.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
It makes more sense to return error statuses, not 1/0.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
It is a Bad Idea (TM) to call mtd_device_register() or
mtd_device_parse_register() twice on the same master MTD. Among other
things, it makes partition overrides (e.g., cmdlinepart) much more
difficult.
Since commit 727dc612c4 ("mtd: part: Create the master device node
when partitioned"), we now have a config option that accomplishes the
same purpose as the double-registration done in diskonchip.c -- it
forces the master MTD to *always* be registered, while partitions may
optionally show up in addition. Eventually, we might like to make
CONFIG_MTD_PARTITIONED_MASTER into the default, but this could be
disruptive to user-space expectations of MTD numbering, so we'll take
that slowly.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Alexander Shiyan <shc_work@mail.ru>
Powerpc powernv platforms allow access to certain system flash devices
through a firmwarwe interface. This change adds an mtd driver for these
flash devices.
Minor updates from Jeremy Kerr and Joel Stanley.
Signed-off-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Reviewed-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
With the planned cgroup writeback support, backing-dev related
declarations will be more widely used across block and cgroup;
unfortunately, including backing-dev.h from include/linux/blkdev.h
makes cyclic include dependency quite likely.
This patch separates out backing-dev-defs.h which only has the
essential definitions and updates blkdev.h to include it. c files
which need access to more backing-dev details now include
backing-dev.h directly. This takes backing-dev.h off the common
include dependency chain making it a lot easier to use it across block
and cgroup.
v2: fs/fat build failure fixed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch cleans up the manual device_create_file() or
class_create_file() calls by replacing with static attribute groups.
It simplifies the code and also avoids the possible races between the
device/class registration and sysfs creations.
For the simplification, also make ubi_class a static instance with
initializers, too.
Amend a bit by Hujianyang.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Sheng Yong <shengyong1@huawei.com>
Signed-off-by: hujianyang <hujianyang@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
During fastmap attaching, check if a volume already exists when adding
the volume to volume tree. NOTE that the issue cannot happen, only if
the on-flash fastmap data is modified.
Signed-off-by: Sheng Yong <shengyong1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
`vol' is a newly allocated value by kzalloc. Initialize it by assignment
instead of `+='.
Signed-off-by: Sheng Yong <shengyong1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
s/fmpl1/fmpl
s/fmpl2/fmpl_wl
Add "WL" to the error message when wrong WL pool magic number is detected.
Signed-off-by: Sheng Yong <shengyong1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
This patch makes ubiblock devices have minor numbers beginning from
0, allocated dynamically independently of the ubi device/volume
number. This property becomes useful because, on 32-bit architectures
with LFS turned off in a userspace program, device minor numbers
over 8 bits cause stat to return -EOVERFLOW. If the device number is
high (>1) due to multiple MTD partitions, such an overflow will occur.
While enabling LFS is clearly a nicer solution, it's often difficult
to turn on in practice globally as many widely distributed packages
don't work with LFS on.
Other storage systems have their own workarounds, with SCSI making
multiple device majors and MMC having a config option for the number
of partitions per device. A completely dynamic minor numbering is
simpler than these. It is unlikely that anyone is depending on a
static minor number since the major is dynamic anyway. In addition,
ubiblock is still relatively new, so now is the time to make such
changes.
Signed-off-by: Dan Ehrenberg <dehrenberg@chromium.org>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Richard Weinberger <richard@nod.at>
Since commit bd31b85960 (which is in 3.2-rc1) nw_gpio_lock is a raw spinlock
that needs usage of the corresponding raw functions.
This fixes:
drivers/mtd/maps/dc21285.c: In function 'nw_en_write':
drivers/mtd/maps/dc21285.c:41:340: warning: passing argument 1 of 'spinlock_check' from incompatible pointer type
spin_lock_irqsave(&nw_gpio_lock, flags);
In file included from include/linux/seqlock.h:35:0,
from include/linux/time.h:5,
from include/linux/stat.h:18,
from include/linux/module.h:10,
from drivers/mtd/maps/dc21285.c:8:
include/linux/spinlock.h:299:102: note: expected 'struct spinlock_t *' but argument is of type 'struct raw_spinlock_t *'
static inline raw_spinlock_t *spinlock_check(spinlock_t *lock)
^
drivers/mtd/maps/dc21285.c:43:25: warning: passing argument 1 of 'spin_unlock_irqrestore' from incompatible pointer type
spin_unlock_irqrestore(&nw_gpio_lock, flags);
^
In file included from include/linux/seqlock.h:35:0,
from include/linux/time.h:5,
from include/linux/stat.h:18,
from include/linux/module.h:10,
from drivers/mtd/maps/dc21285.c:8:
include/linux/spinlock.h:370:91: note: expected 'struct spinlock_t *' but argument is of type 'struct raw_spinlock_t *'
static inline void spin_unlock_irqrestore(spinlock_t *lock, unsigned long flags)
Fixes: bd31b85960 ("locking, ARM: Annotate low level hw locks as raw")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Commit 4612c715a6 ("mtd: cfi: deinline large functions") moved some
code into the cfi_util library without creating a new dependency. So we
can get build failures like the following, when CONFIG_MTD_JEDECPROBE=y
and CONFIG_MTD_CFI_UTIL=m.
drivers/built-in.o: In function `jedec_read_id':
>> jedec_probe.c:(.text+0x187ed8): undefined reference to `cfi_build_cmd_addr'
drivers/built-in.o: In function `jedec_read_mfr':
>> jedec_probe.c:(.text+0x187f4a): undefined reference to `cfi_build_cmd_addr'
drivers/built-in.o: In function `jedec_reset':
>> jedec_probe.c:(.text+0x187fe0): undefined reference to `cfi_send_gen_cmd'
>> jedec_probe.c:(.text+0x188004): undefined reference to `cfi_send_gen_cmd'
>> jedec_probe.c:(.text+0x18802b): undefined reference to `cfi_send_gen_cmd'
>> jedec_probe.c:(.text+0x18804e): undefined reference to `cfi_send_gen_cmd'
drivers/built-in.o: In function `jedec_probe_chip':
>> jedec_probe.c:(.text+0x188130): undefined reference to `cfi_build_cmd_addr'
>> jedec_probe.c:(.text+0x18814d): undefined reference to `cfi_build_cmd_addr'
>> jedec_probe.c:(.text+0x1881dc): undefined reference to `cfi_send_gen_cmd'
>> jedec_probe.c:(.text+0x188203): undefined reference to `cfi_send_gen_cmd'
>> jedec_probe.c:(.text+0x18822d): undefined reference to `cfi_send_gen_cmd'
>> jedec_probe.c:(.text+0x1884c0): undefined reference to `cfi_send_gen_cmd'
>> jedec_probe.c:(.text+0x1884e7): undefined reference to `cfi_send_gen_cmd'
drivers/built-in.o:jedec_probe.c:(.text+0x188511): more undefined references to `cfi_send_gen_cmd' follow
drivers/built-in.o: In function `jedec_probe_chip':
>> jedec_probe.c:(.text+0x188618): undefined reference to `cfi_build_cmd'
So let's express the dependency properly.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Most code already uses consts for the struct kernel_param_ops,
sweep the kernel for the last offending stragglers. Other than
include/linux/moduleparam.h and kernel/params.c all other changes
were generated with the following Coccinelle SmPL patch. Merge
conflicts between trees can be handled with Coccinelle.
In the future git could get Coccinelle merge support to deal with
patch --> fail --> grammar --> Coccinelle --> new patch conflicts
automatically for us on patches where the grammar is available and
the patch is of high confidence. Consider this a feature request.
Test compiled on x86_64 against:
* allnoconfig
* allmodconfig
* allyesconfig
@ const_found @
identifier ops;
@@
const struct kernel_param_ops ops = {
};
@ const_not_found depends on !const_found @
identifier ops;
@@
-struct kernel_param_ops ops = {
+const struct kernel_param_ops ops = {
};
Generated-by: Coccinelle SmPL
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Junio C Hamano <gitster@pobox.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: cocci@systeme.lip6.fr
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
In do_otp_write we must initialize the variable datum before calling
map_word_load_partial. Otherwise the upper bits of datum may be undefined,
which later causes problems in chip_good called by do_write_oneword.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
It's harmless to add 'ofpart' (the only different parser supported in
default mtdpart.c) to plat_nand. That let's us kill off one more custom
partition prober listing.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This is an example of why it doesn't make much sense to put this
information here in the first place. I don't really know what purpose it
serves.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In commit 5018393625 ("mtd: blktrans: change blktrans_getgeo return
value") we fixed the problem that ioctl(HDIO_GETGEO) might return 0
(success) for mtdblock devices which did not implement the feature and
would leave a blank (zero) result.
But now, let's get the error code right. Other code paths on this ioctl
tend to use -ENOTTY to notify the user that the ioctl() is not supported
for the device, so let's use that instead of -EOPNOTSUPP.
Suggested-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Modify function blktrans_getgeo()'s return value to -EOPNOTSUPP when
dev->tr->getgeo == NULL.
We shouldn't make the return value to 0 when dev->tr->getgeo == NULL,
because the function blktrans_getgeo() has an output value "hd_geometry"
which is usually used by some application, if returns 0 (i.e.,
"success"), it will make some application get the wrong information.
Signed-off-by: Wenlin Kang <wenlin.kang@windriver.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Hardware 8 bit ECC requires a different nand_ecclayout. Instead of adding yet
another static struct nand_ecclayout, generate it in code.
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Few recently added entries are missing SECT_4K flag despite of these
flashes supporting 4 KiB erase sectors and 0x20 erase command.
Also add a comment to help avoiding such mistakes in the future.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: Knut Wohlrab <knut.wohlrab@de.bosch.com>
Cc: Huang Shijie <shijie.huang@intel.com>
Cc: Shengzhou Liu <shengzhou.liu@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Copy to/from oob io area might not be aligned to 4 bytes. When 8 bit ECC is
used, the buffer size is 26. Add memcpy16_{to,from}io, and use them to avoid
truncating the buffer. Prefer memcpy32_{to,from}io when the buffer is properly
aligned for better performance.
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
For 4k pages the i.MX NFC hardware uses no more than 218 bytes for 8bit ECC
data. Larger oobsize confuses the logic of copy_spare(). Limit the size of used
oob size to avoid that.
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
To give people without the reference manual at hand a chance to
understand how spare area is handled in the i.MX nand controller,
improve commenting, naming of variables and coding style.
No functional change intended.
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[baruch: declare oob_chunk_size; update comments; reword commit log]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Remove static in front of ctrl. This variable should not be shared
between different instances of brcmnand_probe(), it should be local to
this function and stored on the stack.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The caller already adds a new line and in the other cases there is no
new line added.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
* readtest: the signal-handling code was clobbering the error codes we should
be handling/reporting in this test, rendering it useless. Noticed by Coverity.
* the common SPI NOR flash DT binding (merged for 4.1-rc1) is being revised,
so let's change that before 4.1 is minted.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=13mb
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20150516' of git://git.infradead.org/linux-mtd
Pull MTD fixes from Brian Norris:
"Two MTD fixes for 4.1:
- readtest: the signal-handling code was clobbering the error codes
we should be handling/reporting in this test, rendering it useless.
Noticed by Coverity.
- the common SPI NOR flash DT binding (merged for 4.1-rc1) is being
revised, so let's change that before 4.1 is minted"
* tag 'for-linus-20150516' of git://git.infradead.org/linux-mtd:
Documentation: dt: mtd: replace "nor-jedec" binding with "jedec, spi-nor"
mtd: readtest: don't clobber error reports
There are a few small hooks required for chips like BCM63138 and the
iProc family. Let's introduce those now.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
BCM7xxx chips are supported entirely by the library code, since they use
generic irqchip interfaces and don't need any extra SoC-specific
configuration.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This core originated in Set-Top Box chips (BCM7xxx) but is used in a
variety of other Broadcom chips, including some BCM63xxx, BCM33xx, and
iProc/Cygnus. It's been used only on ARM and MIPS SoCs, so restrict it
to those architectures.
There are multiple revisions of this core throughout the years, and
almost every version broke register compatibility in some small way, but
with some effort, this driver is able to support v4.0, v5.0, v6.x, v7.0,
and v7.1. It's been tested on v5.0, v6.0, v6.1, v7.0, and v7.1 recently,
so there hopefully are no more lurking inconsistencies.
This patch adds just some library support, on which platform drivers can
be built.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
In commit 8ff16cf77c ("Documentation: devicetree: m25p80: add "nor-jedec"
binding"), we added a generic "nor-jedec" binding to catch all
mostly-compatible SPI NOR flash which can be detected via the READ ID
opcode (0x9F). This was discussed and reviewed at the time, however
objections have come up since then as part of this discussion:
http://lkml.kernel.org/g/20150511224646.GJ32500@ld-irv-0074
It seems the parties involved agree that "jedec,spi-nor" does a better
job of capturing the fact that this is SPI-specific, not just any NOR
flash.
This binding was only merged for v4.1-rc1, so it's still OK to change
the naming.
At the same time, let's move the documentation to a better name.
Next up: stop referring to code (drivers/mtd/devices/m25p80.c) from the
documentation.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: devicetree@vger.kernel.org
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Mark Rutland <mark.rutland@arm.com>
On A MIPS 32-cores machine a BUG_ON was triggered because some acesses to
mtd->usecount were done without taking mtd_table_mutex.
kernel: Call Trace:
kernel: [<ffffffff80401818>] __put_mtd_device+0x20/0x50
kernel: [<ffffffff804086f4>] blktrans_release+0x8c/0xd8
kernel: [<ffffffff802577e0>] __blkdev_put+0x1a8/0x200
kernel: [<ffffffff802579a4>] blkdev_close+0x1c/0x30
kernel: [<ffffffff8022006c>] __fput+0xac/0x250
kernel: [<ffffffff80171208>] task_work_run+0xd8/0x120
kernel: [<ffffffff8012c23c>] work_notifysig+0x10/0x18
kernel:
kernel:
Code: 2442ffff ac8202d8 000217fe <00020336> dc820128 10400003
00000000 0040f809 00000000
kernel: ---[ end trace 080fbb4579b47a73 ]---
Fixed by taking the mutex in blktrans_open and blktrans_release.
Note that this locking is already suggested in
include/linux/mtd/blktrans.h:
struct mtd_blktrans_ops {
...
/* Called with mtd_table_mutex held; no race with add/remove */
int (*open)(struct mtd_blktrans_dev *dev);
void (*release)(struct mtd_blktrans_dev *dev);
...
};
But we weren't following it.
Originally reported by (and patched by) Zhang and Giuseppe,
independently. Improved and rewritten.
Cc: stable@vger.kernel.org
Reported-by: Zhang Xingcai <zhangxingcai@huawei.com>
Reported-by: Giuseppe Cantavenera <giuseppe.cantavenera.ext@nokia.com>
Tested-by: Giuseppe Cantavenera <giuseppe.cantavenera.ext@nokia.com>
Acked-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
These are already-documented common bindings for NAND chips. Let's
handle them in nand_base.
If NAND controller drivers need to act on this data before bringing up
the NAND chip (e.g., fill out ECC callback functions, change HW modes,
etc.), then they can do so between calling nand_scan_ident() and
nand_scan_tail().
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We had many entries that were recently added just to allow selecting
some flashes directly but were never used. They weren't providing any
special flash handling, we just needed them due to the lack of some
generic binding string.
With the introduction of "nor-jedec" (in 1103b85) they won't be needed
unless we discover some faulty flash requiring workarounds.
As explained in m25p80 DT documentation we require specifying
"nor-jedec" now as less specific compatible entry.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use dev_pm_ops instead of the legacy suspend/resume callbacks for the MTD
class suspend and resume operations.
While we are at it slightly reorder things to avoid the need for forward
declarations.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In preparation to enable ARCH_MMP on ARM64, a couple of fixes are needed
to build the pxa3xx_nand driver:
Legacy DMA will only used on ARM, so also make it condtional on
CONFIG_ARM.
__raw_{read,write}sl are not available on ARM64 or generically, so use
the readsl/writesl variants instead. Somewhat inconsistently,
{read,write}sl are inherently non-swapping with the generic version
using __raw_{read,write}l.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-mtd@lists.infradead.org
[Brian: added one more __raw_readsl -> readsl]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Now that the driver handles the FIFO draining in a threaded interrupt, we can
base our timeout on jiffies and sleeping, instead of using mdelay.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
return type of wait_for_completion_timeout is unsigned long not int. An
appropriately named unsigned long is added and the assignment fixed up.
This not only should help readability but also handles corner cases
properly.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
wait_for_completion_timeout does not return negative values so
result handling here does not need to check for negative return.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
As all four bytes are written in any case the memset() is in vain.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This statement was written with a cast-to-loff_t to be sure to have a
full 64-bit mask. However, we don't account for the fact that
'1 << this->bbt_erase_shift' might already overflow.
This will not be a problem in practice, since eraseblocks should never
be anywhere near 4GiB. But we can do this for completeness, and quiet
Coverity in the meantime. CID #1226806.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Don't leak this->bbt, and return early if check_create() fails. It helps
to have a single error path to avoid these problems.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The diskonchip driver almost uses the default nand_base hooks as-is,
except that it provides custom on-flash BBT descriptors and avoids using
factory-marked bad blockers.
So let's refactor the BBT initialization code into a private 'late_init'
hook which handles all the private details. Note the usage of
NAND_SKIP_BBTSCAN, which allows us to defer the BBT scan until we've
prepared everything.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Block drivers are responsible for calling flush_dcache_page() on each
BIO request. This operation keeps the I$ coherent with the D$ on
architectures that don't have hardware coherency support. Without this
flush, random crashes are seen when executing user programs from an ext4
filesystem backed by a ubiblock device.
This patch is based on the change implemented in commit 2d4dc890b5
("block: add helpers to run flush_dcache_page() against a bio and a
request's pages").
Fixes: 9d54c8a33e ("UBI: R/O block driver on top of UBI volumes")
Signed-off-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Pull fourth vfs update from Al Viro:
"d_inode() annotations from David Howells (sat in for-next since before
the beginning of merge window) + four assorted fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
RCU pathwalk breakage when running into a symlink overmounting something
fix I_DIO_WAKEUP definition
direct-io: only inc/dec inode->i_dio_count for file systems
fs/9p: fix readdir()
VFS: assorted d_backing_inode() annotations
VFS: fs/inode.c helpers: d_inode() annotations
VFS: fs/cachefiles: d_backing_inode() annotations
VFS: fs library helpers: d_inode() annotations
VFS: assorted weird filesystems: d_inode() annotations
VFS: normal filesystems (and lustre): d_inode() annotations
VFS: security/: d_inode() annotations
VFS: security/: d_backing_inode() annotations
VFS: net/: d_inode() annotations
VFS: net/unix: d_backing_inode() annotations
VFS: kernel/: d_inode() annotations
VFS: audit: d_backing_inode() annotations
VFS: Fix up some ->d_inode accesses in the chelsio driver
VFS: Cachefiles should perform fs modifications on the top layer only
VFS: AF_UNIX sockets should call mknod on the top layer only
* Add Kconfig option for keeping both the 'master' and 'partition' MTDs
registered as devices. This would really make a better default if we could
do it over, as it allows a lot more flexibility in (1) determining the flash
topology of the system from user-space and (2) adding temporary partitions
at runtime (ioctl(BLKPG)). Unfortunately, this would possibly cause
user-space breakage, as it will cause renumbering of the /dev/mtdX devices.
We'll see if we can change this in the future, as there have already been a
few people looking for this feature, and I know others have just been
working around our current limitations instead of fixing them this way.
* Along with the previous change, add some additional information to sysfs, so
user-space can read the offset of each partition within its master device
SPI NOR:
* add new device tree compatible binding to represent the mostly-compatible
class of SPI NOR flash which can be detected by their extended JEDEC ID
bytes, cutting down the duplication of our ID tables
* misc. new IDs
Various other miscellaneous fixes and changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=aIsV
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20150422' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"Common MTD:
- Add Kconfig option for keeping both the 'master' and 'partition'
MTDs registered as devices. This would really make a better
default if we could do it over, as it allows a lot more flexibility
in (1) determining the flash topology of the system from user-space
and (2) adding temporary partitions at runtime (ioctl(BLKPG)).
Unfortunately, this would possibly cause user-space breakage, as it
will cause renumbering of the /dev/mtdX devices. We'll see if we
can change this in the future, as there have already been a few
people looking for this feature, and I know others have just been
working around our current limitations instead of fixing them this
way.
- Along with the previous change, add some additional information to
sysfs, so user-space can read the offset of each partition within
its master device
SPI NOR:
- add new device tree compatible binding to represent the
mostly-compatible class of SPI NOR flash which can be detected by
their extended JEDEC ID bytes, cutting down the duplication of our
ID tables
- misc. new IDs
Various other miscellaneous fixes and changes"
* tag 'for-linus-20150422' of git://git.infradead.org/linux-mtd: (53 commits)
mtd: spi-nor: Add support for Macronix mx25u6435f serial flash
mtd: spi-nor: Add support for Winbond w25q64dw serial flash
mtd: spi-nor: add support for the Winbond W25X05 flash
mtd: spi-nor: support en25s64 device
mtd: m25p80: bind to "nor-jedec" ID, for auto-detection
Documentation: devicetree: m25p80: add "nor-jedec" binding
mtd: Make MTD tests cancelable
mtd: mtd_oobtest: Fix bitflip_limit usage in test case 3
mtd: docg3: remove invalid __exit annotations
mtd: fsl_ifc_nand: use msecs_to_jiffies for time conversion
mtd: atmel_nand: don't map the ROM table if no pmecc table offset in DT
mtd: atmel_nand: add a definition for the oob reserved bytes
mtd: part: Remove partition overlap checks
mtd: part: Add sysfs variable for offset of partition
mtd: part: Create the master device node when partitioned
mtd: ts5500_flash: Fix typo in MODULE_DESCRIPTION in ts5500_flash.c
mtd: denali: Disable sub-page writes in Denali NAND driver
mtd: pxa3xx_nand: cleanup wait_for_completion handling
mtd: nand: gpmi: Check for scan_bbt() error
mtd: nand: gpmi: fixup return type of wait_for_completion_timeout
...
* Powercut emulation for UBI
* A huge update to UBI Fastmap
* Cleanups and bugfixes all over UBI and UBIFS
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=nzVw
-----END PGP SIGNATURE-----
Merge tag 'upstream-4.1-rc1' of git://git.infradead.org/linux-ubifs
Pull UBI/UBIFS updates from Richard Weinberger:
"This pull request includes the following UBI/UBIFS changes:
- powercut emulation for UBI
- a huge update to UBI Fastmap
- cleanups and bugfixes all over UBI and UBIFS"
* tag 'upstream-4.1-rc1' of git://git.infradead.org/linux-ubifs: (50 commits)
UBI: power cut emulation for testing
UBIFS: fix output format of INUM_WATERMARK
UBI: Fastmap: Fall back to scanning mode after ECC error
UBI: Fastmap: Remove is_fm_block()
UBI: Fastmap: Add blank line after declarations
UBI: Fastmap: Remove else after return.
UBI: Fastmap: Introduce may_reserve_for_fm()
UBI: Fastmap: Introduce ubi_fastmap_init()
UBI: Fastmap: Wire up WL accessor functions
UBI: Add accessor functions for WL data structures
UBI: Move fastmap specific functions out of wl.c
UBI: Fastmap: Add new module parameter fm_debug
UBI: Fastmap: Make self_check_eba() depend on fastmap self checking
UBI: Fastmap: Add self check to detect absent PEBs
UBI: Fix stale pointers in ubi->lookuptbl
UBI: Fastmap: Enhance fastmap checking
UBI: Add initial support for fastmap self checks
UBI: Fastmap: Rework fastmap error paths
UBI: Fastmap: Prepare for variable sized fastmaps
UBI: Fastmap: Locking updates
...
Pull trivial tree from Jiri Kosina:
"Usual trivial tree updates. Nothing outstanding -- mostly printk()
and comment fixes and unused identifier removals"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
goldfish: goldfish_tty_probe() is not using 'i' any more
powerpc: Fix comment in smu.h
qla2xxx: Fix printks in ql_log message
lib: correct link to the original source for div64_u64
si2168, tda10071, m88ds3103: Fix firmware wording
usb: storage: Fix printk in isd200_log_config()
qla2xxx: Fix printk in qla25xx_setup_mode
init/main: fix reset_device comment
ipwireless: missing assignment
goldfish: remove unreachable line of code
coredump: Fix do_coredump() comment
stacktrace.h: remove duplicate declaration task_struct
smpboot.h: Remove unused function prototype
treewide: Fix typo in printk messages
treewide: Fix typo in printk messages
mod_devicetable: fix comment for match_flags
Emulate random power cuts by switching device to ro after a number of
writes to allow simple power cut testing with nand-sim.
Maximum and minimum number of successful writes before power cut and
what kind of writes (EC header, VID header or none) to interrupt
configurable via debugfs.
Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
Signed-off-by: Richard Weinberger <richard@nod.at>
Add Macronix (mx25u6435f) 8MB flash to the list of supported chips.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add Winbond (w25q64dw) 8MB flash to the list of supported chips.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add support for EON en25s64 SPI flash.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use the new 'nor-jedec' binding to provide automatic detection of flash
that use the 0x9F READ ID opcode. This can help for use cases where
platforms just specify compatibility with "m25p80", and then see
messages like this:
m25p80 spi32766.0: found s25fl256s1, expected m25p80
Instead, they can just specify the generic string and see this:
m25p80 spi32766.0: s25fl256s1 (32768 Kbytes)
Also, update the language about m25p_ids[] to straighten out the
expectations here. We should no longer need to continuously grow the
m25p_ids[] table, and in fact, we might want to start removing entries
which are not used in device trees so far, so we can just default to
auto-detection as much as possible in the future.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Rafał Miłecki <zajec5@gmail.com>
I always go nuts when I start an MTD test on a slow device and have to
wait forever until it finishes. From the debug output I already know
what the issue is but I have to wait or reset the board hard. Resetting
is often not an option (remote access, you don't want lose the current
state, etc...).
The solution is easy, check for pending signals at key positions in the
code. Using that one can even stop a test by pressing CTRL-C as
insmod/modprobe have SIGINT pending.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In test case 3, we set vary_offset to write at different
offsets and lengths in the OOB available area. We need to
do the bitflip_limit check while checking for 0xff outside the
OOB offset + length area that we didn't modify during write.
Signed-off-by: Roger Quadros <rogerq@ti.com>
[Brian: whitespace fixup]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The .remove callback may be used when detaching a device via sysfs, so
we can't expect to free up this memory.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
This is only an API consolidation and should make things more readable
it replaces var * HZ / 1000 by msecs_to_jiffies(var) which helps readability
and also handles all corner-cases properly.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
if atmel,pmecc-lookup-table-offset is not found in DT node, we don't
need to map the ROM table as we will build a runtime gf table anyway.
Reported-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
It's better to use a macro instead of just a number.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch makes MTD dynamic partitioning more flexible by removing
overlap checks for dynamic partitions. I don't see any particular
reason why overlapping dynamic partitions should be prohibited while
static partitions are allowed to overlap freely.
The checks previously had an off-by-one error, where 'end' should be
one less than what it is currently set at, and adding partitions out of
increasing order will fail. Disabling the checks resolves this issue.
Signed-off-by: Dan Ehrenberg <dehrenberg@chromium.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch makes a sysfs variable called 'offset' on each partition
which contains the offset in bytes from the beginning of the master
device that the partition starts.
Signed-off-by: Dan Ehrenberg <dehrenberg@chromium.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
For many use cases, it helps to have a device node for the entire
MTD device as well as device nodes for the individual partitions.
For example, this allows querying the entire device's properties.
A common idiom is to create an additional partition which spans
over the whole device.
This patch makes a config option, CONFIG_MTD_PARTITIONED_MASTER,
which makes the master partition present even when the device is
partitioned. This isn't turned on by default since it presents
a backwards-incompatible device numbering.
The patch also makes the parent of a partition device be the master,
if the config flag is set, now that the master is a full device.
Signed-off-by: Dan Ehrenberg <dehrenberg@chromium.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch fixes a spelling typo in MODULE_DESCRIPTION in
ts5500_flash.c.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
[ Brian: fixed grammar in a spelling patch :) ]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The Denali Controller IP does not support sub-page writes.
Signed-off-by: Graham Moore <grmoore@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
return type of wait_for_completion_timeout is unsigned long not int, this
patch uses the return value of wait_for_completion_timeout in the condition
directly rather than assigning it to an incorrect type variable.
The variable used for handling the return of wait_for_cmpletion_timeout
was int but should be unsigned long, where it was not in use for
anything else and the return value in case of completion (>0) is not
used it was removed and wait_for_completion_timeout() used directly in
the if condition.
To make the timeout values a bit simpler to read and also handle all of
the corner cases correctly the declarations are moved to
msecs_to_jiffies().
The timeout declaration cleanup is just for readability
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In case of scan_bbt() failure, we should better propagate it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Huang Shijie <shijie.huang@intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
return type of wait_for_completion_timeout is unsigned long not int. The
return variable is renamed to reflect its use and the type adjusted to
unsigned long.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Huang Shijie <shijie.huang@intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
return type of wait_for_completion_timeout is unsigned long not int, this
patch uses the return value of wait_for_completion_timeout in the condition
directly rather than adding a additional appropriately typed variable.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Han Xu <han.xu@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When displaying dev_err() messages it is useful to print the error value.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Han Xu <han.xu@freescale.com>
[Brian: fix up "can not" at the same time]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
These lines were all indented one tab more than they should be.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Even if bus is not hot-pluggable, the devices can be unbound from the
driver via sysfs, so we should not be using __exit annotations on
remove() methods. The only exception is drivers registered with
platform_driver_probe() which specifically disables sysfs bind/unbind
attributes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Two config options exist to define powerpc MPC8xx:
* CONFIG_PPC_8xx
* CONFIG_8xx
In addition, CONFIG_PPC_8xx also defines CONFIG_CPM1 as
communication co-processor
arch/powerpc/platforms/Kconfig.cputype has contained the following
comment about CONFIG_8xx item for some years:
"# this is temp to handle compat with arch=ppc"
It looks like not many places still have that old CONFIG_8xx used,
so it is likely to be a good time to get rid of it completely ?
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Without this patch the timings are all set to 0 if not specified in the dts.
With this patch the driver falls back to use the defaults that are already
present in the driver and are known to work okay for some (older) boards.
Tested on a custom SPEAr600 based board.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
If a NAND device is not really present or pin muxes are not correctly
configured we can lock up the kernel waiting infinitely for NAND_STATUS
to be ready.
This can be easily reproduced on TI's DRA7-evm board by booting it
without NAND support in u-boot and disabling NAND pin muxes in the kernel.
Add timeout when waiting for NAND_CMD_RESET completion. As per ONFi v4.0
tRST can be upto 250ms for EZ-NAND and 5ms for raw NAND.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Flash lock/unlock is a flash-specific operations. Factor out a callback
for it to more readily support other vendors.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: VIET NGA DAO <vndao@altera.com>
If we encounter an uncorrectable ECC error while scanning for the fastmap
UBI must not fail hard. Instead fall back to scanning mode.
Reported-by: Alexander Block <Alexander.Block@continental-corporation.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
This function was added to fastmap in a very early stage
to have paranoid assertions.
With the current fastmap implementation this assert will never
trigger as fastmap PEBs are not seen by the WL sub-system.
Remove it to save us some CPU cycles.
Signed-off-by: Richard Weinberger <richard@nod.at>
Fastmap need access to various WL data structures as
fastmap tightly depends on WL.
To make the access less invasive add accessor functions.
Signed-off-by: Richard Weinberger <richard@nod.at>
Fastmap is tightly connected to the WL sub-system, many fastmap-specific
functionslive in wl.c.
To get rid of most #ifdefs in wl.c move this functions into a new file
and include it into wl.c
Signed-off-by: Richard Weinberger <richard@nod.at>
If fm_debug is set fastmap debugging is enabled by default.
This is useful if one wants to debug fastmap on an UBI device
with serves the rootfs.
The the UBI attach mechanism runs long before debugfs can be mounted
and chk_fastmap set.
Signed-off-by: Richard Weinberger <richard@nod.at>
This self check allows Fastmap to detect absent PEBs while
writing a new fastmap to the MTD device.
It will help to find implementation issues in Fastmap.
Signed-off-by: Richard Weinberger <richard@nod.at>
In some error paths the WL sub-system gives up on a PEB
and frees it's ubi_wl_entry struct but does not set
the entry in ubi->lookuptbl to NULL.
Fastmap can stumble over such a stale pointer as it uses
ubi->lookuptbl to find all PEBs.
Fix this by introducing a new helper function which free()s
a WL entry and removes the reference from the lookup table.
Signed-off-by: Richard Weinberger <richard@nod.at>
Don't update the fastmap upon detach if fastmap checking is enabled.
This is poor men's power cut testing feature. :-)
Signed-off-by: Richard Weinberger <richard@nod.at>
Using this debugfs knob fastmap self checks can be controlled.
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Tanya Brokhman <tlinder@codeaurora.org>
If UBI is unable to write the fastmap to the device
we have make sure that upon next attach UBI will fall
back to scanning mode.
In case we cannot ensure that they only thing we can do
is falling back to read-only mode.
The current error handling code is not powercut proof.
It could happen that a powercut while invalidating would
lead to a state where an too old fastmap could be used upon
attach.
This patch addresses the issue by writing a fake fastmap
super block to a fresh PEB instead of reerasing the existing one.
The fake fastmap super block will UBI case to do a full scan.
Signed-off-by: Richard Weinberger <richard@nod.at>
The current code assumes that each fastmap has the same amount of PEBs.
So far this is true but will change soon.
Signed-off-by: Richard Weinberger <richard@nod.at>
a) Rename ubi->fm_sem to ubi->fm_eba_sem as this semaphore
protects EBA changes.
b) Turn ubi->fm_mutex into a rw semaphore. It will still serialize
fastmap writes but also ensures that ubi_wl_put_peb() is not
interrupted by a fastmap write. We use a rw semaphore to allow
ubi_wl_put_peb() still to be executed in parallel if no fastmap
write is happening.
Signed-off-by: Richard Weinberger <richard@nod.at>
ubi_wl_get_peb() returns a fresh PEB which can be used by
user of UBI. Due to the pool logic fastmap will correctly
map this PEB upon attach time because it will be scanned.
If a new fastmap is written (due to heavy parallel io)
while the before the fresh PEB is assigned to the EBA table
it will not be scanned as it is no longer in the pool.
So, the race window exists between ubi_wl_get_peb()
and the EBA table assignment.
We have to make sure that no new fastmap can be written
while that.
To ensure that ubi_wl_get_peb() will grab ubi->fm_sem in read mode
and the user of ubi_wl_get_peb() has to release it after the PEB
got assigned.
Signed-off-by: Richard Weinberger <richard@nod.at>
Don't use a fixed size for the WL pool.
Make it instead 50% of the user pool.
We don't make it 100% as it is not as heavily used as the user pool.
Signed-off-by: Richard Weinberger <richard@nod.at>
This logic is in vain as we treat protected PEBs also as used, so this
case must not happen.
If a PEB is found which is in the EBA table but not known as used
has to be issued as fatal error.
Signed-off-by: Richard Weinberger <richard@nod.at>
It is legal to have PEBs left in the used list.
This can happen if UBI copies a PEB and a powercut happens
between writing a new fastmap and adding this PEB into the EBA table.
In this case the old PEB will be used.
Signed-off-by: Richard Weinberger <richard@nod.at>
This function a) requests a new PEB, b) writes data to it,
c) returns the old PEB and d) registers the new PEB in the EBA table.
For the non-fastmap case this works perfectly fine and is powercut safe.
Is fastmap enabled this can lead to issues.
If a new fastmap is written between a) and c) the freshly requested PEB
is no longer in a pool and will not be scanned upon attaching.
If now a powercut happens between c) and d) the freshly requested PEB
will not be scanned and the old one got already scheduled for erase.
After attaching the EBA table will point to a erased PEB.
Fix this issue by swapping steps c) and d).
Signed-off-by: Richard Weinberger <richard@nod.at>
There is always exactly one ubi_attach_info object allocated,
therefore we don't have to care about the name.
Signed-off-by: Richard Weinberger <richard@nod.at>
There is no need to switch to ro mode if ubi_update_fastmap() fails.
Also get rid of the ifdef.
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Tanya Brokhman <tlinder@codeaurora.org>
...such that we can implement NOP variants of some functions.
This will help to reduce fastmap specific ifdefs in other c files.
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Tanya Brokhman <tlinder@codeaurora.org>
If ubi_update_fastmap() fails notify the user.
This is not a hard error as ubi_update_fastmap() makes sure that upon failure
the current on-flash fastmap will no be used upon next UBI attach.
Signed-off-by: Richard Weinberger <richard@nod.at>
Add a ubi_fastmap_close() to free all resources used by fastmap
at WL shutdown.
Signed-off-by: Richard Weinberger <richard@nod.at>
Tested-by: Guido Martínez <guido@vanguardiasur.com.ar>
Reviewed-by: Guido Martínez <guido@vanguardiasur.com.ar>
There is no need to allocate new ones every time, we can reuse
the existing ones.
This makes the code cleaner and more easy to follow.
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Tanya Brokhman <tlinder@codeaurora.org>
Reviewed-by: Guido Martínez <guido@vanguardiasur.com.ar>
Currently ubi_refill_pools() first fills the first and then
the second one.
If only very few free PEBs are available the second pool can get
zero PEBs.
Change ubi_refill_pools() to distribute free PEBs fair between
all pools.
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Guido Martínez <guido@vanguardiasur.com.ar>
Make it two functions, wl_get_wle() and wl_get_peb().
wl_get_peb() works exactly like __wl_get_peb() but wl_get_wle()
does not call produce_free_peb().
While refilling the fastmap user pool we cannot release ubi->wl_lock
as produce_free_peb() does.
Hence the fastmap logic uses now wl_get_wle().
Signed-off-by: Richard Weinberger <richard@nod.at>
ubi_wl_get_peb() has two problems, it reads the pool
size and usage counters without any protection.
While reading one value would be perfectly fine it reads multiple
values and compares them. This is racy and can lead to incorrect
pool handling.
Furthermore ubi_update_fastmap() is called without wl_lock held,
before incrementing the used counter it needs to be checked again.
It could happen that another thread consumed all PEBs from the
pool and the counter goes beyond ->size.
Signed-off-by: Richard Weinberger <richard@nod.at>
...otherwise the deferred work might run after datastructures
got freed and corrupt memory.
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Guido Martínez <guido@vanguardiasur.com.ar>
If the WL pool runs out of PEBs we schedule a fastmap write
to refill it as soon as possible.
Ensure that only one at a time is scheduled otherwise we might end in
a fastmap write storm because writing the fastmap can schedule another
write if bitflips are detected.
Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Tanya Brokhman <tlinder@codeaurora.org>
Reviewed-by: Guido Martínez <guido@vanguardiasur.com.ar>
The kerneldoc for @vid_hdr_aloffset continues onto a second line, but
this is not obvious, because the second line isn't indented, and it
begins with '@'.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
The comparison from the previous line seems to have been erroneously
(partially) copied-and-pasted onto the next. The second line should be
checking req.bytes, not req.lnum.
Coverity CID #139400
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
[rw: Fixed comparison]
Signed-off-by: Richard Weinberger <richard@nod.at>
In some of the 'out_not_moved' error paths, lnum may be used
uninitialized. Don't ignore the warning; let's fix it.
This uninitialized variable doesn't have much visible effect in the end,
since we just schedule the PEB for erasure, and its LEB number doesn't
really matter (it just gets printed in debug messages). But let's get it
straight anyway.
Coverity CID #113449
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
If aeb->len >= vol->reserved_pebs, we should not be writing aeb into the
PEB->LEB mapping.
Caught by Coverity, CID #711212.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
We are completely discarding the earlier value of 'bitflips', which
could reflect a bitflip found in ubi_io_read_vid_hdr(). Let's use the
bitwise OR of header and data 'bitflip' statuses instead.
Coverity CID #1226856
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
forgot to put braces where they should be.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=SIBr
-----END PGP SIGNATURE-----
Merge tag 'upstream-4.0-rc5' of git://git.infradead.org/linux-ubifs
Pull UBI fix from Artem Bityutskiy:
"This fixes a bug introduced during the v4.0 merge window where we
forgot to put braces where they should be"
* tag 'upstream-4.0-rc5' of git://git.infradead.org/linux-ubifs:
UBI: fix missing brace control flow
We're not initializing the ooblen field. Our users don't care, since
they check that oobbuf == NULL first, but it's good practice to zero
unused fields out.
We can drop the NULL initializations since we're memset()ing the whole
thing.
Noticed by Coverity, CID #200821, #200822
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The only exit (break) from the preceding loop is nested within a
condition which yields req == NULL. This code is dead.
Coverity CID #752669
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Coverity noticed that these 'ret' assignments weren't being used. Let's
use them.
Note that nand_lock() and nand_unlock() are still not officially used by
any drivers.
Coverity CIDs #1227054 and #1227037
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
'ret' is always zero, so this is all dead code.
This should quiet Coverity CID #1226739.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
If no devices were found, we would already have skipped over this code.
Detected by Coverity, CID #744270
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
The PARAM command was long unimplemented and it probably wasn't
noticed because chip probing using only the few bytes returned by the
READID command are good enough in most cases to determine the chip in
use.
Still to notice such a shortcoming earlier in the future would be nice
in case it's something more vital.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The mxc-nand driver never supported the PARAM command to read out the
ONFI parameter page and so always relied on probing my manufacturer and
device id (as provided by the READID command).
This patch implements reading out the first parameter page copy at least
which should be good enough in practise.
This makes the boot log change from
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xb1
nand: Micron NAND 128MiB 1,8V 16-bit
to
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xb1
nand: Micron MT29F1G16ABBDAH4
on my machine.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The mxc-nand controller works pagewise and so usually only sends
commands to the flash chip with column == 0. A request with column != 0
from the upper layer is then fulfilled by indexing appropriately into the
device's RAM buffer.
To be able to access the ONFI marker at offset 0x20 in reply to the
READID command however it's invalid to read 32 bytes starting from
column 0.
So let the function used to send the address cycles send the column
address actually passed instead of 0 and fix all callers to pass 0
instead appropriately. Also add some warnings in case this patch changes
the drivers semantics.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When the hardware operates in 16 bit mode it always reads 16 bits even
for operations that only have the lower 8 bits defined. So the upper
bits must be discarded. Do this in the read_byte callback instead of
when reading the NAND id to support reading byte wise more than 5 bytes
and at other occations (like reading the ONFI parameter page).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
At least on i.MX25 (i.e. NFCv2) preset_v2 is called with mtd->writesize
== 0 that is before the connect flash chip is detected. It then
configures for 8 bit ECC mode which needs 26 bytes of OOB per 512 bytes
main section. For flashes with a smaller OOB area issuing a read page
command makes the controller stuck with this config.
Note that this currently doesn't hurt because the first read page
command is issued only after detection is complete and preset is called
once more.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
While extending the mxc-nand driver it happend to me a few times that
the device was stuck and this made the machine hang during boot. So
implement a timeout and print a stack trace the first time this happens
to make it debuggable. The return type of the waiting function is also
changed to int to be able to handle the timeout in the caller.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Currently the driver read NFC command registers to get NFC busy flag.
Actually this flag also can be get by reading HSMC_SR register.
Use the read NFC command registers need mapping a huge memory region.
To save the mapped memory region, we change to check NFC busy flag by
reading HSMC_SR register.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The IRQF_DISABLED flag is a NOOP and has been scheduled for removal
since Linux v2.6.36 by commit 6932bf37be ("genirq: Remove
IRQF_DISABLED from core code").
According to commit e58aa3d2d0 ("genirq: Run irq handlers with
interrupts disabled"), running IRQ handlers with interrupts
enabled can cause stack overflows when the interrupt line of the
issuing device is still active.
This patch ends the grace period for IRQF_DISABLED (i.e.,
SA_INTERRUPT in older versions of Linux) and removes the
definition and all remaining usages of this flag.
There's still a few non-functional references left in the kernel
source:
- The bigger hunk in Documentation/scsi/ncr53c8xx.txt is removed entirely
as IRQF_DISABLED is gone now; the usage in older kernel versions
(including the old SA_INTERRUPT flag) should be discouraged. The
trouble of using IRQF_SHARED is a general problem and not specific to
any driver.
- I left the reference in Documentation/PCI/MSI-HOWTO.txt untouched since
it has already been removed in linux-next.
- All remaining references are changelogs that I suggest to keep.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Cc: Afzal Mohammed <afzal@ti.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Ewan Milne <emilne@redhat.com>
Cc: Eyal Perry <eyalpe@mellanox.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Hongliang Tao <taohl@lemote.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nishanth Menon <nm@ti.com>
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Quentin Lambert <lambert.quentin@gmail.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Sricharan R <r.sricharan@ti.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Zhou Wang <wangzhou1@hisilicon.com>
Cc: iss_storagedev@hp.com
Cc: linux-mips@linux-mips.org
Cc: linux-mtd@lists.infradead.org
Link: http://lkml.kernel.org/r/1425565425-12604-1-git-send-email-valentinrothberg@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fix typo, "Unkown" -> "Unknown"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
If NO_DMA=y:
drivers/built-in.o: In function `hisi_nfc_probe':
hisi504_nand.c:(.text+0x23e646): undefined reference to `dmam_alloc_coherent'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
s3c2410_nand_probe is not the name of the function.
These prints have little utility, so let's just kill them.
Reported-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
pxa3xx_flash_ids wasn't initialized to 0, which in certain cases could
end up containing corrupted values in its members. Fix this to avoid
possible issues.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
As the devicetree binding doesn't require num_cs to exist or be strictly
positive, and neither does the platform data case, a bug appear when
num_cs is set to 0 and panics the kernel.
The issue is that in alloc_nand_resource(), chip is dereferenced without
having a value assigned when num_cs == 0.
Fix this by returning ENODEV is num_cs == 0.
The panic seen is :
Unable to handle kernel NULL pointer dereference at virtual address 000002b8
pgd = c0004000
[000002b8] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT ARM
Modules linked in:
Hardware name: Marvell PXA3xx (Device Tree Support)
task: c3822aa0 ti: c3826000 task.ti: c3826000
PC is at alloc_nand_resource+0x180/0x4a8
LR is at alloc_nand_resource+0xa0/0x4a8
pc : [<c0275b90>] lr : [<c0275ab0>] psr: 68000013
sp : c3827d90 ip : 00000000 fp : 00000000
r10: c3862200 r9 : 0000005e r8 : 00000000
r7 : c3865610 r6 : c3862210 r5 : c3924210 r4 : c3862200
r3 : 00000000 r2 : 00000000 r1 : 00000000 r0 : 00000000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 0000397f Table: 80004018 DAC: 00000035
Process swapper (pid: 1, stack limit = 0xc3826198)
Stack: (0xc3827d90 to 0xc3828000)
...zip...
[<c0275b90>] (alloc_nand_resource) from [<c0275ff8>] (pxa3xx_nand_probe+0x140/0x978)
[<c0275ff8>] (pxa3xx_nand_probe) from [<c0258c40>] (platform_drv_probe+0x48/0xa4)
[<c0258c40>] (platform_drv_probe) from [<c0257650>] (driver_probe_device+0x80/0x21c)
[<c0257650>] (driver_probe_device) from [<c0257878>] (__driver_attach+0x8c/0x90)
[<c0257878>] (__driver_attach) from [<c0255ec4>] (bus_for_each_dev+0x58/0x88)
[<c0255ec4>] (bus_for_each_dev) from [<c0256ec8>] (bus_add_driver+0xd8/0x1d4)
[<c0256ec8>] (bus_add_driver) from [<c0257f14>] (driver_register+0x78/0xf4)
[<c0257f14>] (driver_register) from [<c00088a8>] (do_one_initcall+0x80/0x1e4)
[<c00088a8>] (do_one_initcall) from [<c048ed08>] (kernel_init_freeable+0xec/0x1b4)
[<c048ed08>] (kernel_init_freeable) from [<c0377d8c>] (kernel_init+0x8/0xe4)
[<c0377d8c>] (kernel_init) from [<c00095f8>] (ret_from_fork+0x14/0x3c)
Code: e503b234 e5953008 e1530001 caffffd1 (e59002b8)
---[ end trace a5770060c8441895 ]---
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Change the handling of the data stage in the driver : don't pump data in
the top-half interrupt, but rather schedule a thread for non dma cases.
This will enable latencies in the data pumping, especially if delays are
required. Moreover platform shall be more reactive as other interrupts
can be served while pumping data.
No throughput degradation was observed, at least on the zylonite
platform, while a slight degradation was being expected.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The NDDB register holds the data that are needed by the read and write
commands.
However, during a read PIO access, the datasheet specifies that after each 32
bytes read in that register, when BCH is enabled, we have to make sure that the
RDDREQ bit is set in the NDSR register.
This fixes an issue that was seen on the Armada 385, and presumably other mvebu
SoCs, when a read on a newly erased page would end up in the driver reporting a
timeout from the NAND.
Cc: <stable@vger.kernel.org> # v3.14
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Ensures that block2mtd is triggered after the block devices are enumerated
at boot time.
This issue is seen on BCM2835 (Raspberry Pi) systems when mounting JFFS2
block2mtd filesystems, probably because of the delay on enumerating a USB
MMC card reader.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rodrigo Freire <rfreire@redhat.com>
Signed-off-by: Herton Krzesinski <herton@redhat.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
commit 0e707ae79b ("UBI: do propagate positive error codes up") seems
to have produced an unintended change in the control flow here.
Completely untested, but it looks obvious.
Caught by Coverity, which didn't like the indentation. CID 1271184.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Current sh_flctl sets dma_slave_config :: slave_id field for DMAEngine,
but it is no longer needed. Let's remove it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
NAND:
* Add new Hisilicon NAND driver for Hip04
* Add default reboot handler, to ensure all outstanding erase transactions
complete in time
* jz4740: convert to use GPIO descriptor API
* Atmel: add support for sama5d4
* Change default bitflip threshold to 75% of correction strength
* Miscellaneous cleanups and bugfixes
SPI NOR:
* Freescale QuadSPI:
- Fix a few probe() and remove() issues
- Add a MAINTAINERS entry for this driver
- Tweak transfer size to increase read performance
- Add suspend/resume support
* Add Micron quad I/O support
* ST FSM SPI: miscellaneous fixes
JFFS2:
* gracefully handle corrupted 'offset' field found on flash
Other:
* bcm47xxpart: add tweaks for a few new devices
* mtdconcat: set return lengths properly for mtd_write_oob()
* map_ram: enable use with mtdoops
* maps: support fallback to ROM/UBI for write-protected NOR flash
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=+nRk
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20150216' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"NAND:
- Add new Hisilicon NAND driver for Hip04
- Add default reboot handler, to ensure all outstanding erase
transactions complete in time
- jz4740: convert to use GPIO descriptor API
- Atmel: add support for sama5d4
- Change default bitflip threshold to 75% of correction strength
- Miscellaneous cleanups and bugfixes
SPI NOR:
- Freescale QuadSPI:
- Fix a few probe() and remove() issues
- Add a MAINTAINERS entry for this driver
- Tweak transfer size to increase read performance
- Add suspend/resume support
- Add Micron quad I/O support
- ST FSM SPI: miscellaneous fixes
JFFS2:
- gracefully handle corrupted 'offset' field found on flash
Other:
- bcm47xxpart: add tweaks for a few new devices
- mtdconcat: set return lengths properly for mtd_write_oob()
- map_ram: enable use with mtdoops
- maps: support fallback to ROM/UBI for write-protected NOR flash"
* tag 'for-linus-20150216' of git://git.infradead.org/linux-mtd: (46 commits)
mtd: hisilicon: && vs & typo
jffs2: fix handling of corrupted summary length
mtd: hisilicon: add device tree binding documentation
mtd: hisilicon: add a new NAND controller driver for hisilicon hip04 Soc
mtd: avoid registering reboot notifier twice
mtd: concat: set the return lengths properly
mtd: kconfig: replace PPC_OF with PPC
mtd: denali: remove unnecessary stubs
mtd: nand: remove redundant local variable
MAINTAINERS: add maintainer entry for FREESCALE QUAD SPI driver
mtd: fsl-quadspi: improve read performance by increase AHB transfer size
mtd: fsl-quadspi: Remove unnecessary 'map_failed' label
mtd: fsl-quadspi: Remove unneeded success/error messages
mtd: fsl-quadspi: Fix the error paths
mtd: nand: omap: drop condition with no effect
mtd: nand: jz4740: Convert to GPIO descriptor API
mtd: nand: Request strength instead of bytes for soft BCH
mtd: nand: default bitflip-reporting threshold to 75% of correction strength
mtd: atmel_nand: introduce a new compatible string for sama5d4 chip
mtd: atmel_nand: return max bitflips in all sectors in pmecc_correction()
...
Pull UBI and UBIFS updates from Richard Weinberger:
- cleanups and bug fixes all over UBI and UBIFS
- block-mq support for UBI Block
- UBI volumes can now be renamed while they are in use
- security.* XATTR support for UBIFS
- a maintainer update
* 'for-linus-v3.20' of git://git.infradead.org/linux-ubifs:
UBI: block: Fix checking for NULL instead of IS_ERR()
UBI: block: Continue creating ubiblocks after an initialization error
UBIFS: return -EINVAL if log head is empty
UBI: Block: Explain usage of blk_rq_map_sg()
UBI: fix soft lockup in ubi_check_volume()
UBI: Fastmap: Care about the protection queue
UBIFS: add a couple of extra asserts
UBI: do propagate positive error codes up
UBI: clean-up printing helpers
UBI: extend UBI layer debug/messaging capabilities - cosmetics
UBIFS: add ubifs_err() to print error reason
UBIFS: Add security.* XATTR support for the UBIFS
UBIFS: Add xattr support for symlinks
UBI: Block: Add blk-mq support
UBI: Add initial support for scatter gather
UBI: rename_volumes: Use UBI_METAONLY
UBI: Implement UBI_METAONLY
Add myself as UBI co-maintainer
The intent was to mask away some bits here, not to test true or false.
Fix: 54f531f6e3 ('mtd: hisilicon: add a new NAND controller driver for hisilicon hip04 Soc')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We recently switched from allocating ->rq using blk_init_queue() to
use blk_mq_init_queue() so we need to update the error handling to
check for IS_ERR() instead of NULL.
Fixes: ff1f48ee3b ('UBI: Block: Add blk-mq support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
If one ubi volume is corrupted but another is not, it should be
possible to initialize that ubiblock from a kernel commandline which
includes both of them. This patch changes the error handling behavior
in initializing ubiblock to ensure that all parameters are attempted
even if one fails. If there is a failure, it is logged on dmesg.
It also makes error messages more descriptive by including the
name of the UBI volume that failed.
Tested: Formatted ubi volume /dev/ubi5_0 in a corrupt way and
dev/ubi3_0 properly and included "ubi.block=5,0 ubi.block=3,0" on
the kernel command line. At boot, I see the following in the console:
[ 21.082420] UBI error: ubiblock_create_from_param: block: can't open volume on ubi5_0, err=-19
[ 21.084268] UBI: ubiblock3_0 created from ubi3:0(rootfs)
Signed-off-by: Dan Ehrenberg <dehrenberg@chromium.org>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Richard Weinberger <richard@nod.at>
This patch adds the support for hisilicon 504 NAND controller which is now used
by Hisilicon Soc Hip04.
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Calling mtd_device_parse_register with the same mtd_info
(e.g. registering several partitions on a single device)
would add the same reboot notifier twice, causing an
infinte loop in notifier_chain_register during boot up.
Signed-off-by: Niklas Cassel <nks@flawful.org>
[Brian: add FIXME comments]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In concat_read_oob both retlen and oobretlen should be updated.
concat_write_oob previously only (improperly) updated retlen.
Signed-off-by: Niklas Cassel <niklass@axis.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The PPC_OF is a ppc specific option which is used to mean that the
firmware device tree access functions are available. Since all the
ppc platforms have a device tree, it is aways set to 'y' for ppc.
So it makes no sense to keep a such option in the current kernel.
Replace it with PPC.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This driver uses NAND_ECC_HW_SYNDROME mode. The nand_scan_tail()
function would not complain about missing ecc->calculate,
ecc->correct, ecc->hwctl handlers.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Set AHB transfer size to 1K which improved the read performance.
Add ahb_buf_size field in fsl_qspi_devtype_data to denote the size for
different SoC.
Before:
root@imx6qdlsolo:~# dd if=/dev/mtd1 of=/dev/null bs=1M count=16
16+0 records in
16+0 records out
16777216 bytes (17 MB) copied, 0.472183 s, 25.1 MB/s
After:
root@imx6qdlsolo:~# dd if=/dev/mtd1 of=/dev/null bs=1M count=16
16+0 records in
16+0 records out
16777216 bytes (17 MB) copied, 0.369439 s, 29.5 MB/s
Signed-off-by: Allen Xu <b45815@freescale.com>
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Huang Shijie <shijie.huang@intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
There is no need to keep the 'map_failed' label. We can simply return the error
code directly and let the code shorter and cleaner.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Han Xu <han.xu@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When the driver successfully probe we already have messages like:
[ 1.140989] fsl-quadspi 21e4000.qspi: s25fl128s (16384 Kbytes)
[ 1.150902] fsl-quadspi 21e4000.qspi: s25fl128s (16384 Kbytes)
Or in case of error:
[ 1.175920] fsl-quadspi: probe of 21e4000.qspi failed with error -12
, so remove the unneeded success/error messages.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Han Xu <han.xu@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Jumping to 'map_failed' label is not correct at these points, as it misses to
disable the clocks that were previously enabled.
Jump to 'irq_failed' label instead that will correctly disable the clocks.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Han Xu <han.xu@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The if and the else branch code are identical - so the condition has no
effect on the effective code. This patch removes the condition and the
duplicated code and updates the documentation as suggested by
Roger Quadros <rogerq@ti.com>.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Reviewed-by: Pekon Gupta <pekon@pek-sem.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use the GPIO descriptor API instead of the deprecated legacy GPIO API to
manage the busy GPIO.
The patch updates both the jz4740 nand driver and the only user of the driver
the qi-lb60 board driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Previously, we requested that drivers pass ecc.size and ecc.bytes when
using NAND_ECC_SOFT_BCH. However, a driver is likely to only know the ECC
strength required for its NAND, so each driver would need to perform a
strength-to-bytes calculation.
Avoid duplicating this calculation in each driver by asking drivers to
pass ecc.size and ecc.strength so that the strength-to-bytes calculation
need only be implemented once.
This reverts/generalizes this commit:
mtd: nand: Base BCH ECC bytes on required strength
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The recently added mtd_mmap_capabilities can be used from loadable
modules, in particular romfs, but is not exported, so we get
ERROR: "mtd_mmap_capabilities" [fs/romfs/romfs.ko] undefined!
This adds the missing export.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: b4caecd480 ("fs: introduce f_op->mmap_capabilities for nommu mmap support")
Acked-by: Christoph Hellwig <hch@lst.de>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Fastmap can miss a PEB if it is in the protection queue
and not jet in the used tree.
Treat every protected PEB as used.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
UBI uses positive function return codes internally, and should not propagate
them up, except in the place this path fixes. Here is the original bug report
from Dan Carpenter:
The problem is really in ubi_eba_read_leb().
drivers/mtd/ubi/eba.c
412 err = ubi_io_read_vid_hdr(ubi, pnum, vid_hdr, 1);
413 if (err && err != UBI_IO_BITFLIPS) {
414 if (err > 0) {
415 /*
416 * The header is either absent or corrupted.
417 * The former case means there is a bug -
418 * switch to read-only mode just in case.
419 * The latter case means a real corruption - we
420 * may try to recover data. FIXME: but this is
421 * not implemented.
422 */
423 if (err == UBI_IO_BAD_HDR_EBADMSG ||
424 err == UBI_IO_BAD_HDR) {
425 ubi_warn("corrupted VID header at PEB %d, LEB %d:%d",
426 pnum, vol_id, lnum);
427 err = -EBADMSG;
428 } else
429 ubi_ro_mode(ubi);
On this path we return UBI_IO_FF and UBI_IO_FF_BITFLIPS and it
eventually gets passed to ERR_PTR(). We probably dereference the bad
pointer and oops. At that point we've gone read only so it was already
a bad situation...
430 }
431 goto out_free;
432 } else if (err == UBI_IO_BITFLIPS)
433 scrub = 1;
434
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Let's prefix UBI messages with 'ubiX' instead of 'UBI-X' - this is more
consistent with the way we name UBI devices.
Also, commit "32608703 UBI: Extend UBI layer debug/messaging capabilities"
added the function name print to 'ubi_msg()' - lets revert this change, since
these messages are supposed to be just informative messages, and not debugging
messages.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Some cosmetic fixes to the patch "UBI: Extend UBI layer debug/messaging
capabilities".
Signed-off-by: Tanya Brokhman <tlinder@codeaurora.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Adds a new set of functions to deal with scatter gather.
ubi_eba_read_leb_sg() will read from a LEB into a scatter gather list.
The new data structure struct ubi_sgl will be used within UBI to
hold the scatter gather list itself and metadata to have a cursor
within the list.
Signed-off-by: Richard Weinberger <richard@nod.at>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
By using UBI_METAONLY in rename_volumes() it is now possible to rename
an UBI volume atomically while it is open for writing.
This is useful for firmware upgrades.
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: Andrew Murray <amurray@embedded-bits.co.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
Tested-by: Guido Martínez <guido@vanguardiasur.com.ar>
Reviewed-by: Guido Martínez <guido@vanguardiasur.com.ar>
Tested-by: Christoph Fritz <chf.fritz@googlemail.com>
Tested-by: Andrew Murray <amurray@embedded-bits.co.uk>
UBI_METAONLY is a new open mode for UBI volumes, it indicates
that only meta data is being changed.
Meta data in terms of UBI volumes means data which is stored in the
UBI volume table but not on the volume itself.
While it does not interfere with UBI_READONLY and UBI_READWRITE
it is not allowed to use UBI_METAONLY together with UBI_EXCLUSIVE.
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: Andrew Murray <amurray@embedded-bits.co.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
Tested-by: Guido Martínez <guido@vanguardiasur.com.ar>
Reviewed-by: Guido Martínez <guido@vanguardiasur.com.ar>
Tested-by: Christoph Fritz <chf.fritz@googlemail.com>
Tested-by: Andrew Murray <amurray@embedded-bits.co.uk>
The MTD API reports -EUCLEAN only if the maximum number of bitflips
found in any ECC block exceeds a certain threshold. This is done to
avoid excessive -EUCLEAN reports to MTD users, which may induce
additional scrubbing of data, even when the ECC algorithm in use is
perfectly capable of handling the bitflips.
This threshold can be controlled by user-space (via sysfs), to allow
users to determine what they are willing to tolerate in their
application. But it still helps to have sane defaults.
In recent discussion [1], it was pointed out that our default threshold
is equal to the correction strength. That means that we won't actually
report any -EUCLEAN (i.e., "bitflips were corrected") errors until there
are almost too many to handle. It was determined that 3/4 of the
correction strength is probably a better default.
[1] http://lists.infradead.org/pipermail/linux-mtd/2015-January/057259.html
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <shijie.huang@intel.com>
Since "BDI: Provide backing device capability information [try #3]" the
backing_dev_info structure also provides flags for the kind of mmap
operation available in a nommu environment, which is entirely unrelated
to it's original purpose.
Introduce a new nommu-only file operation to provide this information to
the nommu mmap code instead. Splitting this from the backing_dev_info
structure allows to remove lots of backing_dev_info instance that aren't
otherwise needed, and entirely gets rid of the concept of providing a
backing_dev_info for a character device. It also removes the need for
the mtd_inodefs filesystem.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Tejun Heo <tj@kernel.org>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Since in SAMA5D4 chip, the PMECC can correct bit flips in erased page.
So we add a DT property to indicate this hardware character.
If the PMECC support correct bitflip erased page (all data are 0xff).
Then we can use the PMECC correct the page and skip the erased page
check.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
atmel_nand_pmecc_read_page() will return the total bitflips in this
page. This is incorrect.
As one nand page includes multiple ecc sectors, that will cause the
returned total bitflips exceed ecc capablity.
So this patch will make pmecc_correct() return the max bitflips of all
sectors in the page. That also makes atmel_nand_pmecc_read_page() return
the max bitflips.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When removing the fsl-quadspi module and running 'cat /proc/mtd' afterwards,
we see garbage data like:
$ rmmod fsl-quadspi
$ cat /proc/mtd
dev: size erasesize name
mtd0: 00000000 00000000 "(null)"
mtd0: 00000000 00000000 "(null)"
mtd0: 00000000 00000000 "(null)"
...
mtd0: a22296c6c756e28 00000000 "(null)"
mtd0: a22296c6c756e28 3064746d "(null)"
If we continue doing multiple module load/unload operations, then it will also
lead to a kernel crash.
The reason for this is due to the wrong mtd index used in
mtd_device_unregister() in the remove function.
We need to keep the mtd unregister index aligned with the one used in the probe
function, which means we need to take into account the 'has_second_chip'
property. By doing so we can guarantee that the mtd index is the same in the
registration and unregistration functions.
With this patch applied we can load/unload the fsl-quadspi driver several times
and it will result in no crash.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Huang Shijie <shijie.huang@intel.com>
Tested-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Allen Xu <han.xu@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
There is no path to switch to STATE_DATAOUT_STATUS_M state, and
OPT_SMARTMEDIA is unused.
This is leftover from commit 0be718e552
("mtd: nand: remove a bunch of unused commands").
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In initialization routine, mtd_info->owner is overwritten by memset()
just after being initialized. This can be fixed by moving memset() calls
to just before setting mtd_info->owner. But the memory region is allocated
by kmalloc, so we can fix it by using kzalloc instead of kmalloc.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jonathan McDowell <noodles@earth.li>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
i.mx6 sx support turn off fastmix and megamix power.
qpsi controller can be turned off and all status lost when suspend/resume.
add suspend/resume functions and reset qspi controller when resume.
Signed-off-by: Allen Xu <b45815@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Huang Shijie <shijie.huang@intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
commit 3157d1ed23 ("mtd: denali: remove unnecessary casts") introduced
an error by using a wrong bitmask.
A uint16_t cast was replaced with & 0xff, should be & 0xffff.
Signed-off-by: Graham Moore <grmoore@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
drivers/mtd/devices/st_spi_fsm.c:1647:17:
warning: comparison between signed and unsigned integer expressions
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
ST's Common Clk Framework is now available. This patch ensures the FSM
makes use of it by obtaining and enabling the EMI clock. If system fails
to provide the EMI clock, we bomb out.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Under certain conditions, the SPI-FSM Controller can be left in a state where
the data FIFO is not entirely empty. This can lead to problems where subsequent
data transfers appear to have been shifted by a number of unidentified bytes.
One simple example would be an errant FSM sequence which loaded more data to the
FIFO than was read by the host. Another more interesting case results from an
obscure artefact in the FSM Controller. When switching from data transfers in
x4 or x2 mode to data transfers in x1 mode, extraneous bytes will appear in the
FIFO, unless the previous data transfer was a multiple of 32 cycles (i.e. 8
bytes for x2, and 16 bytes for x4). This applies equally whether FSM is being
operated directly by a S/W driver, or by the SPI boot-controller in FSM-Boot
mode. Furthermore, data in the FIFO not only survive a transition between
FSM-Boot and FSM, but also a S/W reset of IP block [1].
By taking certain precautions, it is possible to prevent the driver from causing
this type of problem (e.g. ensuring that the host and programmed sequence
agree on the transfer size, and restricting transfer sizes to multiples of
32-cycles [2]). However, at the point the driver is loaded, no assumptions can be
made regarding the state of the FIFO. Even if previous S/W drivers have behaved
correctly, it is impossible to control the number of transactions serviced by
the controller operating in FSM-Boot.
To address this problem, we ensure the FIFO is cleared during initialisation,
before performing any FSM operations. Previously, the fsm_clear_fifo() code was
capable of detecting and clearing any unwanted 32-bit words from the FIFO. This
patch extends the capability to handle an arbitrary number of bytes present in
the FIFO [3]. Now that the issue is better understood, we also remove the calls
to fsm_clear_fifo() following the fsm_read() and fsm_write() operations.
The process of actually clearing the FIFO deserves a mention. While the FIFO
may contain any number of bytes, the SPI_FAST_SEQ_STA register only reports the
number of complete 32-bit words present. Furthermore, data can only be drained
from the FIFO by reading complete 32-bit words. With this in mind, a two stage
process is used to the clear the FIFO:
1. Read any complete 32-bit words from the FIFO, as reported by the
SPI_FAST_SEQ_STA register.
2. Mop up any remaining bytes. At this point, it is not known if there
are 0, 1, 2, or 3 bytes in the FIFO. To handle all cases, a dummy
FSM sequence is used to load one byte at a time, until a complete
32-bit word is formed; at most, 4 bytes will need to be loaded.
[1] Although this issue has existed since early versions of the SPI-FSM
controller, its full extent only emerged recently as a consequence of the
targetpacks starting to use FSM-Boot(x4) as the default configuration.
[2] The requirement to restrict transfers to multiples of 32 cycles was found
empirically back when DUAL and QUAD mode support was added. The current
analysis now gives a satisfactory explanation for this requirement.
[3] Theoretically, it is possible for the FIFO to contain an arbitrary number of
bits. However, since there are no known use-cases that leave incomplete
bytes in the FIFO, only words and bytes are considered here.
Signed-off-by: Angus Clark <angus.clark@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
UBI needs to know the physical erase block size, even on read-only
devices, since it defines the on-device layout. Use a device-tree
provided value to support previously written UBI on read-only NOR.
UBI also needs a non-zero writebufsize, so we set it to one.
Note: This was implemented because hardware write-protected CFI
NOR cannot be probed for the physical erase block size.
Signed-off-by: Joe Schultz <jschultz@xes-inc.ccom>
Signed-off-by: Aaron Sierra <asierra@xes-inc.ccom>
[Brian: removed unneeded #ifdef, note 'optional' erase-size property]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Previously, when probing a CFI chip which was write-protected at the
hardware level, the probe would fail due to the fact it could not put
the chip into QUERY mode. This would result in no MTD devices being
created.
Add a fallback to probe using the map_rom driver if the user-selected
probe fails.
Signed-off-by: Joe Schultz <jschultz@xes-inc.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We need to compare ret variable for negative value. The current code
assigns the boolean to the ret and prints it wrongly in the warning
message.
Reported-by: Andrey Karpov <karpov@viva64.com>
Cc: Giel van Schijndel <me@mortis.eu>
Cc: Dimitri Gorokhovik <dimitri.gorokhovik@free.fr>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Commit 7854d3f749 ("mtd: spelling, capitalization, uniformity") added
a correctly spelled line, but failed to remove the wrongly spelled one.
Commit 064a7694b5 ("mtd: Fix typo mtd/tests") then fixed the spelling
again, but left the duplication.
Fixes: 7854d3f749 ("mtd: spelling, capitalization, uniformity")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add nand_shutdown to wait for current nand operations to finish and prevent
further operations by changing the nand flash state to FL_SHUTDOWN.
This is addressing a problem observed during reboot tests using UBIFS
root file system: NAND erase operations that are in progress during
system reboot/shutdown are causing partial erased blocks. Although UBI should
be able to detect and recover from this error, this change will avoid
the creation of partial erased blocks on reboot in the middle of a NAND erase
operation.
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Tested-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
