Add a new radiotap flag to indicate injected frames must not be
reordered relative to other frames that also have this flag set,
independent of priority field values in the transmitted frame.
Parse this radiotap flag and define and set a corresponding Tx
control flag. Note that this flag has recently been standardized
as part of an update to radiotap.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Link: https://lore.kernel.org/r/20201104061823.197407-2-Mathy.Vanhoef@kuleuven.be
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The radiotap specification contains a flag to indicate that the sequence
number of an injected frame should not be overwritten. Parse this flag
and define and set a corresponding Tx control flag.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Link: https://lore.kernel.org/r/20200723100153.31631-2-Mathy.Vanhoef@kuleuven.be
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Most likely the last set of patches for 5.1. WPA3 support to ath10k
and qtnfmac. FTM support to iwlwifi and ath10k. And of course other
new features and bugfixes.
wireless-drivers was merged due to dependency in mt76.
Major changes:
iwlwifi
* HE radiotap
* FTM (Fine Timing Measurement) initiator and responder implementation
* bump supported firmware API to 46
* VHT extended NSS support
* new PCI IDs for 9260 and 22000 series
ath10k
* change QMI interface to support the new (and backwards incompatible)
interface from HL3.1 and used in recent HL2.0 branch firmware
releases
* support WPA3 with WCN3990
* support for mac80211 airtime fairness based on transmit rate
estimation, the firmware needs to support WMI_SERVICE_PEER_STATS to
enable this
* report transmit airtime to mac80211 with firmwares having
WMI_SERVICE_REPORT_AIRTIME feature, this to have more accurate
airtime fairness based on real transmit time (instead of just
estimated from transmit rate)
* support Fine Timing Measurement (FTM) responder role
* add dynamic VLAN support with firmware having WMI_SERVICE_PER_PACKET_SW_ENCRYPT
* switch to use SPDX license identifiers
ath
* add new country codes for US
brcmfmac
* support monitor frames with the hardware/ucode header
qtnfmac
* enable WPA3 SAE and OWE support
mt76
* beacon support for USB devices (mesh+ad-hoc only)
rtlwifi
* convert to use SPDX license identifiers
libertas_tf
* get the MAC address before registering the device
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJccAnlAAoJEG4XJFUm622bxxMH/2cz2GEuDQXOwfYLnCUwFES8
vqTdMWnlfqGQvsTyvtSp91KqsL3hE2FB1Cu3n6/vzND3C7afT0V2/QlU7Pmgr8sR
1gnJnu0NJT5SZfzcTsqwt8rFw9lQZ3HcvEcfNo6T5KUyyY7FGCNGR5H27nvoKOP3
ea1h7U80loPV40sGTI8jj963wa9LNHUrjHTK4wY+KMWECgZuD/fHeE9YPB9MTdff
lJ5bWCoQmuJddvTtC+X0tOAsCkxgdbbw6ieKqzep8H4gtUjerZD+V8uUdbtpr7IL
sWPoaqrrADMv9cZtDVj+pEtNIJ3mpfuHYFKSON9jy/uxygeFTfVzLu43RFreDp8=
=D15/
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2019-02-22' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.1
Most likely the last set of patches for 5.1. WPA3 support to ath10k
and qtnfmac. FTM support to iwlwifi and ath10k. And of course other
new features and bugfixes.
wireless-drivers was merged due to dependency in mt76.
Major changes:
iwlwifi
* HE radiotap
* FTM (Fine Timing Measurement) initiator and responder implementation
* bump supported firmware API to 46
* VHT extended NSS support
* new PCI IDs for 9260 and 22000 series
ath10k
* change QMI interface to support the new (and backwards incompatible)
interface from HL3.1 and used in recent HL2.0 branch firmware
releases
* support WPA3 with WCN3990
* support for mac80211 airtime fairness based on transmit rate
estimation, the firmware needs to support WMI_SERVICE_PEER_STATS to
enable this
* report transmit airtime to mac80211 with firmwares having
WMI_SERVICE_REPORT_AIRTIME feature, this to have more accurate
airtime fairness based on real transmit time (instead of just
estimated from transmit rate)
* support Fine Timing Measurement (FTM) responder role
* add dynamic VLAN support with firmware having WMI_SERVICE_PER_PACKET_SW_ENCRYPT
* switch to use SPDX license identifiers
ath
* add new country codes for US
brcmfmac
* support monitor frames with the hardware/ucode header
qtnfmac
* enable WPA3 SAE and OWE support
mt76
* beacon support for USB devices (mesh+ad-hoc only)
rtlwifi
* convert to use SPDX license identifiers
libertas_tf
* get the MAC address before registering the device
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose the trigger-based PPDU SIG-A bandwidth to radiotap in
the newly defined bits thereof.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For certain sounding frames, it may be useful to report them
to userspace even though they don't have a PSDU in order to
determine the PHY parameters (e.g. VHT rate/stream config.)
Add support for this to mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As before with HE, the data needs to be provided by the
driver in the skb head, since there's not enough space
in the skb CB.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The header file has grown a lot of #define's etc, but
they are nicer as enums, so rewrite the file from the
documentation as such.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The values don't match the radiotap spec, corrected that.
Reported-by: Oz Shalev <oz.shalev@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use the existing device timestamp from the RX status information
to add support for the new radiotap timestamp field. Currently
only 32-bit counters are supported, but we also add the radiotap
mactime where applicable. This new field allows more flexibility
in where the timestamp is taken etc. The non-timestamp data in
the field is taken from a new field in the hw struct.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This capabilities weren't propagated to the radiotap header.
We don't set here the VHT_KNOWN / MCS_HAVE flag because not
all the low level drivers will know how to properly flag
the frames, hence the low level driver will be in charge
of setting IEEE80211_RADIOTAP_MCS_HAVE_FEC,
IEEE80211_RADIOTAP_MCS_HAVE_STBC and / or
IEEE80211_RADIOTAP_VHT_KNOWN_STBC according to its
capabilities.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Wireshark already defines radiotap channel flags for 5 and 10 MHz, so
just use them in Linux radiotap too. Furthermore, add rx status flags to
allow drivers to report when they received data on 5 or 10 MHz channels.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Some chips can tell us if received frame was
encoded with STBC or not. To make this information available
in user space we can use updated radiotap specification:
http://www.radiotap.org/defined-fields/MCS
This patch will set number of STBC encoded spatial streams (Nss).
The HAVE_STBC flag should be provided by driver.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add some information that we have about VHT to radiotap.
This at least lets one see the MCS and NSS information.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Define the A-MPDU status field in radiotap, also
update the radiotap parser for it and the MCS field
that was apparently missed last time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The macro is only used in ipw2200 and we certainly
don't want to encourage its use, so move it out of
the radiotap header file and into the driver.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow injected unicast frames to be sent without having to wait
for an ACK.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the MCS information we currently get
from the drivers into radiotap.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Upstream radiotap has adopted the namespace
proposal David Young made and I then took care
of, for which I had adapted the radiotap parser
as a library outside the kernel. This brings
the in-kernel parser up to speed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In
commit 601ae7f25a
Author: Bruno Randolf <br1@einfach.org>
Date: Thu May 8 19:22:43 2008 +0200
mac80211: make rx radiotap header more flexible
code was added that tried to align the radiotap header
position in memory based on the radiotap header length.
Quite obviously, that is completely useless.
Instead of trying to do that, use unaligned accesses
to generate the radiotap header. To properly do that,
we also need to mark struct ieee80211_radiotap_header
packed, but that is fine since it's already packed
(and it should be marked packed anyway since its a
wire format).
Cc: Bruno Randolf <br1@einfach.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Radiotap was updated to include a "bad PLCP" flag and standardise
the "bad FCS" flag in the "flags" rather than "RX flags" field,
this patch updates Linux to that standard.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No need to pad the header so no constant needed for that,
no need to carry any version number from netbsd nor CVS
IDs from them.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_get_radiotap_len() tries to dereference radiotap length without
taking care that it is completely unaligned and get_unaligned()
is required.
Signed-off-by: Andy Green <andy@warmcat.com>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IEEE80211_RADIOTAP_FCS is obsolete and should not be used. It's no
longer defined. Remove it from the comment too.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Document that all fields must be little endian. Use annotated types
even in the comments. Consistently use shorter type names (u8, s8).
Realign the comments.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the Marvell Libertas 8388 802.11 USB driver.
Signed-off-by: Marcelo Tosatti <marcelo@kvack.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tree 383c59b2516a61f2683f02dfebbed0caf6ee5dc3
parent a04948f63fd96c4b875a43f78afad1a0874cc441
author Mike Kershaw <dragorn@kismetwireless.net> 1124447833 -0500
committer James Ketrenos <jketreno@linux.intel.com> 1127313883 -0500
Added ieee80211_radiotap.h to enhance statistic reporting to user space
from wireless drivers.
Signed-off-by: Mike Kershaw <dragorn@kismetwireless.net>
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
