The PRUSS module has a SYSCFG which is unique. The SYSCFG
has two additional unique fields called STANDBY_INIT and
SUB_MWAIT in addition to regular IDLE_MODE and STANDBY_MODE
fields. Add the bindings for this new sysc type.
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for Turris Mox board (Armada 3720 SoC based)
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCXW5eNQAKCRALBhiOFHI7
1aqnAJsGU/B3GFbhiuwI4+l3In7TMVVpIgCbB1T/eo1RJhvh9kH9zMj641Rmsk0=
=B8dQ
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-5.4-2' of git://git.infradead.org/linux-mvebu into arm/late
mvebu dt64 for 5.4 (part 2)
Add support for Turris Mox board (Armada 3720 SoC based)
* tag 'mvebu-dt64-5.4-2' of git://git.infradead.org/linux-mvebu: (53 commits)
arm64: dts: marvell: add DTS for Turris Mox
dt-bindings: marvell: document Turris Mox compatible
arm64: dts: marvell: armada-37xx: add SPI CS1 pinctrl
arm64: dts: marvell: Add cpu clock node on Armada 7K/8K
arm64: dts: marvell: Convert 7k/8k usb-phy properties to phy-supply
arm64: dts: marvell: Add 7k/8k PHYs in PCIe nodes
arm64: dts: marvell: Add 7k/8k PHYs in USB3 nodes
arm64: dts: marvell: Add 7k/8k per-port PHYs in SATA nodes
arm64: dts: marvell: Add CP110 COMPHY clocks
arm64: dts: marvell: armada-37xx: add mailbox node
dt-bindings: gpio: Document GPIOs via Moxtet bus
drivers: gpio: Add support for GPIOs over Moxtet bus
bus: moxtet: Add sysfs and debugfs documentation
dt-bindings: bus: Document moxtet bus binding
bus: Add support for Moxtet bus
reset: Add support for resets provided by SCMI
firmware: arm_scmi: Add RESET protocol in SCMI v2.0
dt-bindings: arm: Extend SCMI to support new reset protocol
firmware: arm_scmi: Make use SCMI v2.0 fastchannel for performance protocol
firmware: arm_scmi: Add discovery of SCMI v2.0 performance fastchannels
...
Link: https://lore.kernel.org/r/87h85two0r.fsf@FE-laptop
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
On the Turris Mox router different modules can be connected to the main
CPU board: currently a module with a SFP cage, a module with MiniPCIe
connector, a PCIe pass-through MiniPCIe connector module, a 4-port
switch module, an 8-port switch module, and a 4-port USB3 module.
For example:
[CPU]-[PCIe-pass-through]-[PCIe]-[8-port switch]-[8-port switch]-[SFP]
Each of this modules has an input and output shift register, and these
are connected via SPI to the CPU board.
Via SPI we are able to discover which modules are connected, in which
order, and we can also read some information about the modules (eg.
their interrupt status), and configure them.
From each module 8 bits can be read (of which low 4 bits identify the
module) and 8 bits can be written.
For example from the module with a SFP cage we can read the LOS,
TX-FAULT and MOD-DEF0 signals, while we can write TX-DISABLE and
RATE-SELECT signals.
This driver creates a new bus type, called "moxtet". For each Mox module
it finds via SPI, it creates a new device on the moxtet bus so that
drivers can be written for them.
It also implements a virtual interrupt controller for the modules which
send their interrupt status over the SPI shift register. These modules
do this in addition to sending their interrupt status via the shared
interrupt line. When the shared interrupt is triggered, we read from the
shift register and handle IRQs for all devices which are in interrupt.
The topology of how Mox modules are connected can then be read by
listing /sys/bus/moxtet/devices.
Link: https://lore.kernel.org/r/20190812161118.21476-2-marek.behun@nic.cz
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add the appropriate SPDX license identifier to the common
TI sysc bindings header file.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The dra76x MCAN generic interconnect module has a its own
format for the bits in the control registers.
Therefore add a new module type, new regbits and new capabilities
specific to the MCAN module.
Acked-by: Rob Herring <robh@kernel.org>
CC: Tony Lindgren <tony@atomide.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The ti-sysc binding does not yet describe the capabilities of the
interconnect target module. So to make the ti-sysc binding usable
for configuring the interconnect target module, we need to add few
more properties:
1. To detect between omap2 and omap4 timers, let's add compatibles
for them for "ti,sysc-omap2-timer" and,sysc-omap4-timer". This
makes it easier to pick up the already initialized system timers
later on
2. Let's add "ti,sysc-mask" for a mask of features supported by the
interconnect target module. This describes what we have available
in the various SYSCONFIG registers
3. Let's add "ti,sysc-midle" and "ti,sysc-sidle" lists for the master
and slave idle modes supported by the interconnect target module.
These describe the values available for MIDLE and SIDLE bits in
the SYSCONFIG registers
4. Some interconnect target modules need a short delay after reset
before they can be accessed, let's use "ti,sysc-delay-us" for
that
5. Let's add "ti,syss-mask" bit to describe the optional SYSSTATUS
register bits for reset done bits
6. Let's support the two existing custom quirk properties already
listed in Documentation/devicetree/bindings/arm/omap/omap.txt for
"ti,no-reset-on-init" and "ti,no-idle-on-init"
7. And finally, let's add a header for the binding for the dts
files and the driver to use
Cc: Benoît Cousson <bcousson@baylibre.com>
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Nishanth Menon <nm@ti.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: Suman Anna <s-anna@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
