This patch allows drm to populate an agpgart structure with pages of its own.
It's needed for the new drm memory manager which dynamically flips pages in and out of AGP.
The patch modifies the generic functions as well as the intel agp driver. The intel drm driver is
currently the only one supporting the new memory manager.
Other agp drivers may need some minor fixing up once they have a corresponding memory manager enabled drm driver.
AGP memory types >= AGP_USER_TYPES are not populated by the agpgart driver, but the drm is expected
to do that, as well as taking care of cache- and tlb flushing when needed.
It's not possible to request these types from user space using agpgart ioctls.
The Intel driver also gets a new memory type for pages that can be bound cached to the intel GTT.
Signed-off-by: Thomas Hellstrom <thomas@tungstengraphics.com>
Signed-off-by: Dave Jones <davej@redhat.com>
The following video card requires the agpgart driver ioctl
interface in order to detect video memory.
00:02.0 VGA compatible controller: Intel Corporation Mobile
945GM/GMS/940GML Express Integrated Graphics Controller (rev 03)
Tested on a Thinkpad Z61t, Xorg.0.log from a 32bit debian Xorg is at;
http://montezuma.homeunix.net/Xorg.0.log
Signed-off-by: Zwane Mwaikambo <zwane@infradead.org>
Signed-off-by: Dave Jones <davej@redhat.com>
On the G965, the GTT size may be larger than is required to cover the
aperture. (In fact, on all hardware we've seen, the GTT is 512KB to the
aperture's 256MB). A previous commit forced the aperture size to 512MB on
G965 to match GTT, which would likely result in hangs at best if users
tried to rely on agpgart's aperture size information. Instead, we use the
resource length for the aperture size and the system's reported GTT size
when available for the GTT size.
Because the MSAC registers which had been read for aperture size detection
on i9xx chips just cause a change in the resource size, we can use generic
code for aperture detection on all i9xx.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
drivers/char/agp/backend.c: In function `agp_backend_initialize':
drivers/char/agp/backend.c:141: warning: assignment discards qualifiers from pointer target type
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Dave Jones <davej@redhat.com>
When leaving S3 state, the AGP bridge may not have all PCI configuration
registers set in the same way as they were at boot. This should be fixed
by pci_restore_state - however, the APBASE register cannot be set to
conflict with the APSIZE register. If APSIZE is larger than it was before
suspend, pci_restore_state will not restore APBASE correctly. The attached
patch adds an extra item to the agp_bridge_data structure and uses it to
store the value of APBASE. On resume, this is then written after APSIZE
has been set. This patch only touches the path used for Intel chipsets
without integrated graphics, and may need to be extended to work with the
others.
Without this patch, I get the symptoms described in bug 4921 - APBASE ends
up overlapping various PCI devices, and as a result they fail to work after
resume.
Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When Linux is running on the Xen virtual machine monitor, physical
addresses are virtualised and cannot be directly referenced by the AGP
GART. This patch fixes the GART driver for Xen by adding a layer of
abstraction between physical addresses and 'GART addresses'.
Architecture-specific functions are also defined for allocating and freeing
the GATT. Xen requires this to ensure that table really is contiguous from
the point of view of the GART.
These extra interface functions are defined as 'no-ops' for all existing
architectures that use the GART driver.
Signed-off-by: Keir Fraser <keir@xensource.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
