These two sysctls were added because the hardcoded defaults (2 minutes,
tcp, 30 seconds, udp) turned out to be too low for some setups.
They appeared in 5.14-rc1 so it should be fine to remove it again.
Marcelo convinced me that there should be no difference between a flow
that was offloaded vs. a flow that was not wrt. timeout handling.
Thus the default is changed to those for TCP established and UDP stream,
5 days and 120 seconds, respectively.
Marcelo also suggested to account for the timeout value used for the
offloading, this avoids increase beyond the value in the conntrack-sysctl
and will also instantly expire the conntrack entry with altered sysctls.
Example:
nf_conntrack_udp_timeout_stream=60
nf_flowtable_udp_timeout=60
This will remove offloaded udp flows after one minute, rather than two.
An earlier version of this patch also cleared the ASSURED bit to
allow nf_conntrack to evict the entry via early_drop (i.e., table full).
However, it looks like we can safely assume that connection timed out
via HW is still in established state, so this isn't needed.
Quoting Oz:
[..] the hardware sends all packets with a set FIN flags to sw.
[..] Connections that are aged in hardware are expected to be in the
established state.
In case it turns out that back-to-sw-path transition can occur for
'dodgy' connections too (e.g., one side disappeared while software-path
would have been in RETRANS timeout), we can adjust this later.
Cc: Oz Shlomo <ozsh@nvidia.com>
Cc: Paul Blakey <paulb@nvidia.com>
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Use the same family as the request message, for consistency. The
netlink payload provides sufficient information to describe the hook
object, including the family.
This makes it easier to userspace to correlate the hooks are that
visited by the packets for a certain family.
Fixes: e2cf17d377 ("netfilter: add new hook nfnl subsystem")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The sequence number allows to correlate the netlink reply message (as
part of the dump) with the original request message.
The cb->seq field is internally used to detect an interference (update)
of the hook list during the netlink dump, do not use it as sequence
number in the netlink dump header.
Fixes: e2cf17d377 ("netfilter: add new hook nfnl subsystem")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The family is relevant for pseudo-families like NFPROTO_INET
otherwise the user needs to rely on the hook function name to
differentiate it from NFPROTO_IPV4 and NFPROTO_IPV6 names.
Add nfnl_hook_chain_desc_attributes instead of using the existing
NFTA_CHAIN_* attributes, since these do not provide a family number.
Fixes: e2cf17d377 ("netfilter: add new hook nfnl subsystem")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
NFNLA_HOOK_FUNCTION_NAME should include the hook function name only,
the module name is already provided by NFNLA_HOOK_MODULE_NAME.
Fixes: e2cf17d377 ("netfilter: add new hook nfnl subsystem")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Michal Kubecek reports that conntrack gc is responsible for frequent
wakeups (every 125ms) on idle systems.
On busy systems, timed out entries are evicted during lookup.
The gc worker is only needed to remove entries after system becomes idle
after a busy period.
To resolve this, always scan the entire table.
If the scan is taking too long, reschedule so other work_structs can run
and resume from next bucket.
After a completed scan, wait for 2 minutes before the next cycle.
Heuristics for faster re-schedule are removed.
GC_SCAN_INTERVAL could be exposed as a sysctl in the future to allow
tuning this as-needed or even turn the gc worker off.
Reported-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Quite a lot of fixes here, the biggest set being for the cs42l42 driver
which is reasonably old but has seen a sudden uptick in activity.
There's also some fixes for correctly referencing PCM buffer addresses
and the removal of some driver-local bodges that had been done for the
lack of prefix handling in DAPM which were broken by the core handling
that as expected.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmENS7kACgkQJNaLcl1U
h9AxAgf/RDnVYb2b77qhUbHva/5fOUQMCx6NMWQ79LG8rRU2cZ5f+NxJtLKNOQIQ
A05mH0Y4BCQFeCKWN/JpGlJWITUpBLhYIxBe//5URjzkds8h8KCfkxc+UGxYxy/h
xPrXztFRMRD74kQKwpISLxM134qRW0j3fONSAxXwWSmamL2UEefohVX+edsHgl37
vdJNMiBfq8g9fCIq5nT/Il7yNBlEosLoB1UxBpMRElMa+y5ZuYRjl2R8n0CIIbHG
kER2ilNY7ldU1cs+KPbbXcfRrDc3BUs2/eNNSljqJb7XK4pJGndpEKX2i/Bzi5i0
BfPcN7VIm4fG79GbJ/Xw+hsOcA58YA==
=r49k
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v5.14-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.14
Quite a lot of fixes here, the biggest set being for the cs42l42 driver
which is reasonably old but has seen a sudden uptick in activity.
There's also some fixes for correctly referencing PCM buffer addresses
and the removal of some driver-local bodges that had been done for the
lack of prefix handling in DAPM which were broken by the core handling
that as expected.
State transitions from 1->0->1 and N->2->1 callbacks require RCU
synchronization. Rather than performing the RCU synchronization every
time the state change occurs, which is quite slow when many tracepoints
are registered in batch, instead keep a snapshot of the RCU state on the
most recent transitions which belong to a chain, and conditionally wait
for a grace period on the last transition of the chain if one g.p. has
not elapsed since the last snapshot.
This applies to both RCU and SRCU.
This brings the performance regression caused by commit 231264d692
("Fix: tracepoint: static call function vs data state mismatch") back to
what it was originally.
Before this commit:
# trace-cmd start -e all
# time trace-cmd start -p nop
real 0m10.593s
user 0m0.017s
sys 0m0.259s
After this commit:
# trace-cmd start -e all
# time trace-cmd start -p nop
real 0m0.878s
user 0m0.000s
sys 0m0.103s
Link: https://lkml.kernel.org/r/20210805192954.30688-1-mathieu.desnoyers@efficios.com
Link: https://lore.kernel.org/io-uring/4ebea8f0-58c9-e571-fd30-0ce4f6f09c70@samba.org/
Cc: stable@vger.kernel.org
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: "Paul E. McKenney" <paulmck@kernel.org>
Cc: Stefan Metzmacher <metze@samba.org>
Fixes: 231264d692 ("Fix: tracepoint: static call function vs data state mismatch")
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Reviewed-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
There should be this judgement before we create an io-worker
Fixes: 685fe7feed ("io-wq: eliminate the need for a manager thread")
Signed-off-by: Hao Xu <haoxu@linux.alibaba.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There is an acct->nr_worker visit without lock protection. Think about
the case: two callers call io_wqe_wake_worker(), one is the original
context and the other one is an io-worker(by calling
io_wqe_enqueue(wqe, linked)), on two cpus paralelly, this may cause
nr_worker to be larger than max_worker.
Let's fix it by adding lock for it, and let's do nr_workers++ before
create_io_worker. There may be a edge cause that the first caller fails
to create an io-worker, but the second caller doesn't know it and then
quit creating io-worker as well:
say nr_worker = max_worker - 1
cpu 0 cpu 1
io_wqe_wake_worker() io_wqe_wake_worker()
nr_worker < max_worker
nr_worker++
create_io_worker() nr_worker == max_worker
failed return
return
But the chance of this case is very slim.
Fixes: 685fe7feed ("io-wq: eliminate the need for a manager thread")
Signed-off-by: Hao Xu <haoxu@linux.alibaba.com>
[axboe: fix unconditional create_io_worker() call]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A warning as below may be occasionally triggered in an ADL machine when
these conditions occur:
- Two perf record commands run one by one. Both record a PEBS event.
- Both runs on small cores.
- They have different adaptive PEBS configuration (PEBS_DATA_CFG).
[ ] WARNING: CPU: 4 PID: 9874 at arch/x86/events/intel/ds.c:1743 setup_pebs_adaptive_sample_data+0x55e/0x5b0
[ ] RIP: 0010:setup_pebs_adaptive_sample_data+0x55e/0x5b0
[ ] Call Trace:
[ ] <NMI>
[ ] intel_pmu_drain_pebs_icl+0x48b/0x810
[ ] perf_event_nmi_handler+0x41/0x80
[ ] </NMI>
[ ] __perf_event_task_sched_in+0x2c2/0x3a0
Different from the big core, the small core requires the ACK right
before re-enabling counters in the NMI handler, otherwise a stale PEBS
record may be dumped into the later NMI handler, which trigger the
warning.
Add a new mid_ack flag to track the case. Add all PMI handler bits in
the struct x86_hybrid_pmu to track the bits for different types of
PMUs. Apply mid ACK for the small cores on an Alder Lake machine.
The existing hybrid() macro has a compile error when taking address of
a bit-field variable. Add a new macro hybrid_bit() to get the
bit-field value of a given PMU.
Fixes: f83d2f91d2 ("perf/x86/intel: Add Alder Lake Hybrid support")
Reported-by: Ammy Yi <ammy.yi@intel.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Tested-by: Ammy Yi <ammy.yi@intel.com>
Link: https://lkml.kernel.org/r/1627997128-57891-1-git-send-email-kan.liang@linux.intel.com
The gpiod_lookup_table.table passed to gpiod_add_lookup_table() must
be terminated with an empty entry, add this.
Note we have likely been getting away with this not being present because
the GPIO lookup code first matches on the dev_id, causing most lookups to
skip checking the table and the lookups which do check the table will
find a matching entry before reaching the end. With that said, terminating
these tables properly still is obviously the correct thing to do.
Fixes: f8eb0235f6 ("x86: pcengines apuv2 gpio/leds/keys platform driver")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210806115515.12184-1-hdegoede@redhat.com
360 degree hinges devices with dual KIOX010A + KIOX020A accelerometers
always have both a KIOX010A and a KIOX020A ACPI device (one for each
accel).
Theoretical some vendor may re-use some DSDT for a non-convertible
stripping out just the KIOX020A ACPI device from the DSDT. Check that
both ACPI devices are present to make the check more robust.
Fixes: 153cca9caa ("platform/x86: Add and use a dual_accel_detect() helper")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210802141000.978035-1-hdegoede@redhat.com
On s390, the following build warning occurs:
drivers/net/ethernet/marvell/mvpp2/mvpp2.h:844:2: warning: overflow in
conversion from 'long unsigned int' to 'int' changes value from
'18446744073709551584' to '-32' [-Woverflow]
844 | ((total_size) - MVPP2_SKB_HEADROOM - MVPP2_SKB_SHINFO_SIZE)
This happens because MVPP2_SKB_SHINFO_SIZE, which is 320 bytes (which is
already 64-byte aligned) on some architectures, actually gets ALIGN'd up
to 512 bytes in the s390 case.
So then, when this is invoked:
MVPP2_RX_MAX_PKT_SIZE(MVPP2_BM_SHORT_FRAME_SIZE)
...that turns into:
704 - 224 - 512 == -32
...which is not a good frame size to end up with! The warning above is a
bit lucky: it notices a signed/unsigned bad behavior here, which leads
to the real problem of a frame that is too short for its contents.
Increase MVPP2_BM_SHORT_FRAME_SIZE by 32 (from 704 to 736), which is
just exactly big enough. (The other values can't readily be changed
without causing a lot of other problems.)
Fixes: 07dd0a7aae ("mvpp2: add basic XDP support")
Cc: Sven Auhagen <sven.auhagen@voleatech.de>
Cc: Matteo Croce <mcroce@microsoft.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing RxUnicast counter.
Fixes: b8f126a8d5 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no 'NONE' version of 'enum mcu_cipher_type', and returning
'MT_CIPHER_NONE' causes a warning:
drivers/net/wireless/mediatek/mt76/mt7921/mcu.c: In function 'mt7921_mcu_get_cipher':
drivers/net/wireless/mediatek/mt76/mt7921/mcu.c:114:24: error: implicit conversion from 'enum mt76_cipher_type' to 'enum mcu_cipher_type' [-Werror=enum-conversion]
114 | return MT_CIPHER_NONE;
| ^~~~~~~~~~~~~~
Add the missing MCU_CIPHER_NONE defintion that fits in here with
the same value.
Fixes: c368362c36 ("mt76: fix iv and CCMP header insertion")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721150745.1914829-1-arnd@kernel.org
Previous atomic increment/decrement logic expects the atomic count to be
'0' after the final decrement.
Replacing atomic count with refcount does not allow that, as
refcount_dec() considers count of 1 as underflow and triggers a kernel
splat.
Fix the current refcount logic by using the usual pattern of decrementing
the refcount and test if it is '0' on the final deref in
c4iw_destroy_cq(). Use wait_for_completion() instead of wait_event().
Fixes: 7183451f84 ("RDMA/cxgb4: Use refcount_t instead of atomic_t for reference counting")
Link: https://lore.kernel.org/r/1628167412-12114-1-git-send-email-dakshaja@chelsio.com
Signed-off-by: Dakshaja Uppalapati <dakshaja@chelsio.com>
Reviewed-by: Potnuri Bharat Teja <bharat@chelsio.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
DMUB firmware info is printed before it gets initialized.
Correct this order to ensure true value is conveyed.
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
HPD disable and enable sequences are not mutually exclusive
on Linux. For HPDs that spans over 1s (i.e. HPD low = 1s),
part of the disable sequence (specifically, a request to SMU
to lower refclk) could come right before the call to PHY
enable, causing DMUB to access an unresponsive PHY
and thus a hard hang on the system.
[How]
Disable 48mhz refclk off on native DP.
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] On S4 resume we also need to fix detection of when to reload DMCUB
firmware because we're currently using the VBIOS version which isn't
compatible with the driver version.
[How] Update the hardware init check for DCN31 since it's the ASIC that
has this issue.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Jude Shih <jude.shih@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Hardware team suggested to use SRExitTime= 35.5us as w/a to prevent
underflow in certain modes.
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Bing Guo <bing.guo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Why:
In DCN2x, HW doesn't automatically divide MASTER_UPDATE_LOCK_DB_X
by the number of pipes ODM Combined.
How:
Set MASTER_UPDATE_LOCK_DB_X to the value that is adjusted by the
number of pipes ODM Combined.
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Bing Guo <bing.guo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
For DCN31 onward, LTTPR is to be enabled and set to Transparent by
VBIOS. Driver is to assume that VBIOS has done this without needing to
check the VBIOS interop bit.
[HOW]
Add LTTPR enable and interop VBIOS bits into dc->caps, and force-set the
interop bit to true for DCN31+.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
'pm_suspend_target_state' is only available when CONFIG_PM_SLEEP
is set/enabled. OTOH, when both SUSPEND and HIBERNATION are not set,
PM_SLEEP is not set, so this variable cannot be used.
../drivers/gpu/drm/amd/amdgpu/amdgpu_acpi.c: In function ‘amdgpu_acpi_is_s0ix_active’:
../drivers/gpu/drm/amd/amdgpu/amdgpu_acpi.c:1046:11: error: ‘pm_suspend_target_state’ undeclared (first use in this function); did you mean ‘__KSYM_pm_suspend_target_state’?
return pm_suspend_target_state == PM_SUSPEND_TO_IDLE;
^~~~~~~~~~~~~~~~~~~~~~~
__KSYM_pm_suspend_target_state
Also use shorter IS_ENABLED(CONFIG_foo) notation for checking the
2 config symbols.
Fixes: 91e273712a ("drm/amdgpu: Check pmops for desired suspend state")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: "Pan, Xinhui" <Xinhui.Pan@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Cc: linux-next@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Correct yellow carp driver-PMFW interface version to v4.
Signed-off-by: Xiaomeng Hou <Xiaomeng.Hou@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On a 1->0->1 callbacks transition, there is an issue with the new
callback using the old callback's data.
Considering __DO_TRACE_CALL:
do { \
struct tracepoint_func *it_func_ptr; \
void *__data; \
it_func_ptr = \
rcu_dereference_raw((&__tracepoint_##name)->funcs); \
if (it_func_ptr) { \
__data = (it_func_ptr)->data; \
----> [ delayed here on one CPU (e.g. vcpu preempted by the host) ]
static_call(tp_func_##name)(__data, args); \
} \
} while (0)
It has loaded the tp->funcs of the old callback, so it will try to use the old
data. This can be fixed by adding a RCU sync anywhere in the 1->0->1
transition chain.
On a N->2->1 transition, we need an rcu-sync because you may have a
sequence of 3->2->1 (or 1->2->1) where the element 0 data is unchanged
between 2->1, but was changed from 3->2 (or from 1->2), which may be
observed by the static call. This can be fixed by adding an
unconditional RCU sync in transition 2->1.
Note, this fixes a correctness issue at the cost of adding a tremendous
performance regression to the disabling of tracepoints.
Before this commit:
# trace-cmd start -e all
# time trace-cmd start -p nop
real 0m0.778s
user 0m0.000s
sys 0m0.061s
After this commit:
# trace-cmd start -e all
# time trace-cmd start -p nop
real 0m10.593s
user 0m0.017s
sys 0m0.259s
A follow up fix will introduce a more lightweight scheme based on RCU
get_state and cond_sync, that will return the performance back to what it
was. As both this change and the lightweight versions are complex on their
own, for bisecting any issues that this may cause, they are kept as two
separate changes.
Link: https://lkml.kernel.org/r/20210805132717.23813-3-mathieu.desnoyers@efficios.com
Link: https://lore.kernel.org/io-uring/4ebea8f0-58c9-e571-fd30-0ce4f6f09c70@samba.org/
Cc: stable@vger.kernel.org
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: "Paul E. McKenney" <paulmck@kernel.org>
Cc: Stefan Metzmacher <metze@samba.org>
Fixes: d25e37d89d ("tracepoint: Optimize using static_call()")
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
On transition from 2->1 callees, we should be comparing .data rather
than .func, because the same callback can be registered twice with
different data, and what we care about here is that the data of array
element 0 is unchanged to skip rcu sync.
Link: https://lkml.kernel.org/r/20210805132717.23813-2-mathieu.desnoyers@efficios.com
Link: https://lore.kernel.org/io-uring/4ebea8f0-58c9-e571-fd30-0ce4f6f09c70@samba.org/
Cc: stable@vger.kernel.org
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: "Paul E. McKenney" <paulmck@kernel.org>
Cc: Stefan Metzmacher <metze@samba.org>
Fixes: 547305a646 ("tracepoint: Fix out of sync data passing by static caller")
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Current release - regressions:
- sched: taprio: fix init procedure to avoid inf loop when dumping
- sctp: move the active_key update after sh_keys is added
Current release - new code bugs:
- sparx5: fix build with old GCC & bitmask on 32-bit targets
Previous releases - regressions:
- xfrm: redo the PREEMPT_RT RCU vs hash_resize_mutex deadlock fix
- xfrm: fixes for the compat netlink attribute translator
- phy: micrel: Fix detection of ksz87xx switch
Previous releases - always broken:
- gro: set inner transport header offset in tcp/udp GRO hook to avoid
crashes when such packets reach GSO
- vsock: handle VIRTIO_VSOCK_OP_CREDIT_REQUEST, as required by spec
- dsa: sja1105: fix static FDB entries on SJA1105P/Q/R/S and SJA1110
- bridge: validate the NUD_PERMANENT bit when adding an extern_learn FDB entry
- usb: lan78xx: don't modify phy_device state concurrently
- usb: pegasus: check for errors of IO routines
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=/rrJ
-----END PGP SIGNATURE-----
Merge tag 'net-5.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from ipsec.
Current release - regressions:
- sched: taprio: fix init procedure to avoid inf loop when dumping
- sctp: move the active_key update after sh_keys is added
Current release - new code bugs:
- sparx5: fix build with old GCC & bitmask on 32-bit targets
Previous releases - regressions:
- xfrm: redo the PREEMPT_RT RCU vs hash_resize_mutex deadlock fix
- xfrm: fixes for the compat netlink attribute translator
- phy: micrel: Fix detection of ksz87xx switch
Previous releases - always broken:
- gro: set inner transport header offset in tcp/udp GRO hook to avoid
crashes when such packets reach GSO
- vsock: handle VIRTIO_VSOCK_OP_CREDIT_REQUEST, as required by spec
- dsa: sja1105: fix static FDB entries on SJA1105P/Q/R/S and SJA1110
- bridge: validate the NUD_PERMANENT bit when adding an extern_learn
FDB entry
- usb: lan78xx: don't modify phy_device state concurrently
- usb: pegasus: check for errors of IO routines"
* tag 'net-5.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (48 commits)
net: vxge: fix use-after-free in vxge_device_unregister
net: fec: fix use-after-free in fec_drv_remove
net: pegasus: fix uninit-value in get_interrupt_interval
net: ethernet: ti: am65-cpsw: fix crash in am65_cpsw_port_offload_fwd_mark_update()
bnx2x: fix an error code in bnx2x_nic_load()
net: wwan: iosm: fix recursive lock acquire in unregister
net: wwan: iosm: correct data protocol mask bit
net: wwan: iosm: endianness type correction
net: wwan: iosm: fix lkp buildbot warning
net: usb: lan78xx: don't modify phy_device state concurrently
docs: networking: netdevsim rules
net: usb: pegasus: Remove the changelog and DRIVER_VERSION.
net: usb: pegasus: Check the return value of get_geristers() and friends;
net/prestera: Fix devlink groups leakage in error flow
net: sched: fix lockdep_set_class() typo error for sch->seqlock
net: dsa: qca: ar9331: reorder MDIO write sequence
VSOCK: handle VIRTIO_VSOCK_OP_CREDIT_REQUEST
mptcp: drop unused rcu member in mptcp_pm_addr_entry
net: ipv6: fix returned variable type in ip6_skb_dst_mtu
nfp: update ethtool reporting of pauseframe control
...
buswidth and dtr fields in spi_mem_op are only valid when the
corresponding spi_mem_op phase has a non-zero length. For example,
SPI NAND core doesn't set buswidth when using SPI_MEM_OP_NO_ADDR
phase.
Fix the dtr checks in set_protocol() and suppports_mem_op() to
ignore empty spi_mem_op phases, as checking for dtr field in
empty phase will result in false negatives.
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Link: https://lore.kernel.org/r/20210716232504.182-3-a-nandan@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
I2S always has two LRCLK phases and both CH1 and CH2 of the RX
must be enabled (corresponding to the low and high phases of LRCLK.)
The selection of the valid data channels is done by setting the DAC
CHA_SEL and CHB_SEL. CHA_SEL is always the first (left) channel,
CHB_SEL depends on the number of active channels.
Previously for mono ASP CH2 was not enabled, the result was playing
mono data would not produce any audio output.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 621d65f3b8 ("ASoC: cs42l42: Provide finer control on playback path")
Link: https://lore.kernel.org/r/20210805161111.10410-4-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The lowest valid SCLK corresponds to 44.1 kHz at 16-bit. Sample
rates less than this would produce SCLK below the minimum when using
a normal I2S frame. A constraint must be applied to prevent this.
The constraint is not applied if the machine driver sets SCLK, to
allow setups where the host generates additional bits per LRCLK
phase to increase the SCLK frequency. In these cases the machine
driver would always have to inform this driver of the actual SCLK,
and it must select a legal SCLK.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210805161111.10410-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
An I2S frame starts on the falling edge of LRCLK so ASP_STP must
be 0.
At the same time, move other format settings in the same register
from cs42l42_pll_config() to cs42l42_set_dai_fmt() where you'd
expect to find them, and merge into a single write.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2c394ca796 ("ASoC: Add support for CS42L42 codec")
Link: https://lore.kernel.org/r/20210805161111.10410-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Both SCLK and PLL clocks must be running to drive the glitch-free mux
behind MCLK_SRC_SEL and complete the switchover.
This patch moves the writing of MCLK_SRC_SEL to when the PLL is started
and stopped, so that it only transitions while the PLL is running.
The unconditional write MCLK_SRC_SEL=0 in cs42l42_mute_stream() is safe
because if the PLL is not running MCLK_SRC_SEL is already 0.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 43fc357199 ("ASoC: cs42l42: Set clock source for both ways of stream")
Link: https://lore.kernel.org/r/20210805161111.10410-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
syzbot is hitting might_sleep() warning at hci_sock_dev_event() due to
calling lock_sock() with rw spinlock held [1].
It seems that history of this locking problem is a trial and error.
Commit b40df5743e ("[PATCH] bluetooth: fix socket locking in
hci_sock_dev_event()") in 2.6.21-rc4 changed bh_lock_sock() to
lock_sock() as an attempt to fix lockdep warning.
Then, commit 4ce61d1c7a ("[BLUETOOTH]: Fix locking in
hci_sock_dev_event().") in 2.6.22-rc2 changed lock_sock() to
local_bh_disable() + bh_lock_sock_nested() as an attempt to fix the
sleep in atomic context warning.
Then, commit 4b5dd696f8 ("Bluetooth: Remove local_bh_disable() from
hci_sock.c") in 3.3-rc1 removed local_bh_disable().
Then, commit e305509e67 ("Bluetooth: use correct lock to prevent UAF
of hdev object") in 5.13-rc5 again changed bh_lock_sock_nested() to
lock_sock() as an attempt to fix CVE-2021-3573.
This difficulty comes from current implementation that
hci_sock_dev_event(HCI_DEV_UNREG) is responsible for dropping all
references from sockets because hci_unregister_dev() immediately
reclaims resources as soon as returning from
hci_sock_dev_event(HCI_DEV_UNREG).
But the history suggests that hci_sock_dev_event(HCI_DEV_UNREG) was not
doing what it should do.
Therefore, instead of trying to detach sockets from device, let's accept
not detaching sockets from device at hci_sock_dev_event(HCI_DEV_UNREG),
by moving actual cleanup of resources from hci_unregister_dev() to
hci_cleanup_dev() which is called by bt_host_release() when all
references to this unregistered device (which is a kobject) are gone.
Since hci_sock_dev_event(HCI_DEV_UNREG) no longer resets
hci_pi(sk)->hdev, we need to check whether this device was unregistered
and return an error based on HCI_UNREGISTER flag. There might be subtle
behavioral difference in "monitor the hdev" functionality; please report
if you found something went wrong due to this patch.
Link: https://syzkaller.appspot.com/bug?extid=a5df189917e79d5e59c9 [1]
Reported-by: syzbot <syzbot+a5df189917e79d5e59c9@syzkaller.appspotmail.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes: e305509e67 ("Bluetooth: use correct lock to prevent UAF of hdev object")
Acked-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----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=ewLR
-----END PGP SIGNATURE-----
Merge tag 'selinux-pr-20210805' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux
Pull selinux fix from Paul Moore:
"One small SELinux fix for a problem where an error code was not being
propagated back up to userspace when a bogus SELinux policy is loaded
into the kernel"
* tag 'selinux-pr-20210805' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
selinux: correct the return value when loads initial sids
Pull ucounts fix from Eric Biederman:
"Fix a subtle locking versus reference counting bug in the ucount
changes, found by syzbot"
* 'for-v5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
ucounts: Fix race condition between alloc_ucounts and put_ucounts
- Fix NULL pointer dereference caused by an error path
- Give histogram calculation fields a size, otherwise it breaks synthetic
creation based on them.
- Reject strings being used for number calculations.
- Fix recordmcount.pl warning on llvm building RISC-V allmodconfig
- Fix the draw_functrace.py script to handle the new trace output
- Fix warning of smp_processor_id() in preemptible code
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCYQwR+xQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qtHOAQD7gBn1cRK0T3Eolf5HRd14PLDVUZ1B
iMZuTJZzJUWLSAD/ec3ezcOafNlPKmG1ta8UxrWP5VzHOC5qTIAJYc1d5AA=
=7FNB
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Various tracing fixes:
- Fix NULL pointer dereference caused by an error path
- Give histogram calculation fields a size, otherwise it breaks
synthetic creation based on them.
- Reject strings being used for number calculations.
- Fix recordmcount.pl warning on llvm building RISC-V allmodconfig
- Fix the draw_functrace.py script to handle the new trace output
- Fix warning of smp_processor_id() in preemptible code"
* tag 'trace-v5.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Quiet smp_processor_id() use in preemptable warning in hwlat
scripts/tracing: fix the bug that can't parse raw_trace_func
scripts/recordmcount.pl: Remove check_objcopy() and $can_use_local
tracing: Reject string operand in the histogram expression
tracing / histogram: Give calculation hist_fields a size
tracing: Fix NULL pointer dereference in start_creating
now obeys KVM_CAP_HYPERV_ENFORCE_CPUID. Both the XMM arguments feature
and KVM_CAP_HYPERV_ENFORCE_CPUID are new in 5.14, and each did not know
of the other.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmELlMoUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroOIigf+O1JWYyfVR16qpVnkI9voa0j7aPKd
0v3Qd0ybEbBqOl2QjYFe+aJa42d8bhiMGRG7UNNxYPmW6MukxM3rWZ0wd8IvlktW
KMR/+2jPw8v8B+M44ty9y30cdW65EGxY8PXPrzSXSF9wT5v0fV8s14Yzxkc1edKM
X3OVJk1AhlRaGN9PyGl3MJxdvQG7Ci9Ep500i5vhAsdb2Azu9TzfQRVUUJ8c2BWj
PEI31Z+E0//G0oU/MiHZ5bsYCboiciiHHJxpdFpxVYN7rQ4sOxJswEsO+PpD00K3
HsZXuTXCRQyZfjbI5QlwNWpU6mZrAb3T8GVNBOP+0g3+fDNyrZzJBiCzbQ==
=bI5h
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"Mostly bugfixes; plus, support for XMM arguments to Hyper-V hypercalls
now obeys KVM_CAP_HYPERV_ENFORCE_CPUID.
Both the XMM arguments feature and KVM_CAP_HYPERV_ENFORCE_CPUID are
new in 5.14, and each did not know of the other"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86/mmu: Fix per-cpu counter corruption on 32-bit builds
KVM: selftests: fix hyperv_clock test
KVM: SVM: improve the code readability for ASID management
KVM: SVM: Fix off-by-one indexing when nullifying last used SEV VMCB
KVM: Do not leak memory for duplicate debugfs directories
KVM: selftests: Test access to XMM fast hypercalls
KVM: x86: hyper-v: Check if guest is allowed to use XMM registers for hypercall input
KVM: x86: Introduce trace_kvm_hv_hypercall_done()
KVM: x86: hyper-v: Check access to hypercall before reading XMM registers
KVM: x86: accept userspace interrupt only if no event is injected
Pull pcmcia fix from Dominik Brodowski:
"Zheyu Ma found and fixed a null pointer dereference bug in the device
driver for the i82092 card reader"
* 'pcmcia-next' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/linux:
pcmcia: i82092: fix a null pointer dereference bug
Fix the following kernel-doc warning that appears when building with W=1:
block/partitions/ldm.c:31: warning: expecting prototype for ldm().
Prototype was for ldm_debug() instead
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20210805173447.3249906-1-bvanassche@acm.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This program always prints 4096 and hangs before the patch, and always
prints 8192 and exits successfully after:
int main()
{
int pipefd[2];
for (int i = 0; i < 1025; i++)
if (pipe(pipefd) == -1)
return 1;
size_t bufsz = fcntl(pipefd[1], F_GETPIPE_SZ);
printf("%zd\n", bufsz);
char *buf = calloc(bufsz, 1);
write(pipefd[1], buf, bufsz);
read(pipefd[0], buf, bufsz-1);
write(pipefd[1], buf, 1);
}
Note that you may need to increase your RLIMIT_NOFILE before running the
program.
Fixes: 759c01142a ("pipe: limit the per-user amount of pages allocated in pipes")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/lkml/1628086770.5rn8p04n6j.none@localhost/
Link: https://lore.kernel.org/lkml/1628127094.lxxn016tj7.none@localhost/
Signed-off-by: Alex Xu (Hello71) <alex_y_xu@yahoo.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If queue is dying while iolatency_set_limit() is in progress,
blk_get_queue() won't increment the refcount of the queue. However,
blk_put_queue() will still decrement the refcount later, which will
cause the refcout to be unbalanced.
Thus error out in such case to fix the problem.
Fixes: 8c772a9bfc ("blk-iolatency: fix IO hang due to negative inflight counter")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/20210805124645.543797-1-yukuai3@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pavel Skripkin says:
====================
net: fix use-after-free bugs
I've added new checker to smatch yesterday. It warns about using
netdev_priv() pointer after free_{netdev,candev}() call. I hope, it will
get into next smatch release.
Some of the reported bugs are fixed and upstreamed already, but Dan ran new
smatch with allmodconfig and found 2 more. Big thanks to Dan for doing it,
because I totally forgot to do it.
====================
Link: https://lore.kernel.org/r/cover.1628091954.git.paskripkin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Smatch says:
drivers/net/ethernet/neterion/vxge/vxge-main.c:3518 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev);
drivers/net/ethernet/neterion/vxge/vxge-main.c:3518 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev);
drivers/net/ethernet/neterion/vxge/vxge-main.c:3520 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev);
drivers/net/ethernet/neterion/vxge/vxge-main.c:3520 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev);
Since vdev pointer is netdev private data accessing it after free_netdev()
call can cause use-after-free bug. Fix it by moving free_netdev() call at
the end of the function
Fixes: 6cca200362 ("vxge: cleanup probe error paths")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Smatch says:
drivers/net/ethernet/freescale/fec_main.c:3994 fec_drv_remove() error: Using fep after free_{netdev,candev}(ndev);
drivers/net/ethernet/freescale/fec_main.c:3995 fec_drv_remove() error: Using fep after free_{netdev,candev}(ndev);
Since fep pointer is netdev private data, accessing it after free_netdev()
call can cause use-after-free bug. Fix it by moving free_netdev() call at
the end of the function
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: a31eda65ba ("net: fec: fix clock count mis-match")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Syzbot reported uninit value pegasus_probe(). The problem was in missing
error handling.
get_interrupt_interval() internally calls read_eprom_word() which can
fail in some cases. For example: failed to receive usb control message.
These cases should be handled to prevent uninit value bug, since
read_eprom_word() will not initialize passed stack variable in case of
internal failure.
Fail log:
BUG: KMSAN: uninit-value in get_interrupt_interval drivers/net/usb/pegasus.c:746 [inline]
BUG: KMSAN: uninit-value in pegasus_probe+0x10e7/0x4080 drivers/net/usb/pegasus.c:1152
CPU: 1 PID: 825 Comm: kworker/1:1 Not tainted 5.12.0-rc6-syzkaller #0
...
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:79 [inline]
dump_stack+0x24c/0x2e0 lib/dump_stack.c:120
kmsan_report+0xfb/0x1e0 mm/kmsan/kmsan_report.c:118
__msan_warning+0x5c/0xa0 mm/kmsan/kmsan_instr.c:197
get_interrupt_interval drivers/net/usb/pegasus.c:746 [inline]
pegasus_probe+0x10e7/0x4080 drivers/net/usb/pegasus.c:1152
....
Local variable ----data.i@pegasus_probe created at:
get_interrupt_interval drivers/net/usb/pegasus.c:1151 [inline]
pegasus_probe+0xe57/0x4080 drivers/net/usb/pegasus.c:1152
get_interrupt_interval drivers/net/usb/pegasus.c:1151 [inline]
pegasus_probe+0xe57/0x4080 drivers/net/usb/pegasus.c:1152
Reported-and-tested-by: syzbot+02c9f70f3afae308464a@syzkaller.appspotmail.com
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/20210804143005.439-1-paskripkin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The hardware latency detector (hwlat) has a mode that it runs one thread
across CPUs. The logic to move from the currently running CPU to the next
one in the list does a smp_processor_id() to find where it currently is.
Unfortunately, it's done with preemption enabled, and this triggers a
warning for using smp_processor_id() in a preempt enabled section.
As it is only using smp_processor_id() to get information on where it
currently is in order to simply move it to the next CPU, it doesn't really
care if it got moved in the mean time. It will simply balance out later if
such a case arises.
Switch smp_processor_id() to raw_smp_processor_id() to quiet that warning.
Link: https://lkml.kernel.org/r/20210804141848.79edadc0@oasis.local.home
Acked-by: Daniel Bristot de Oliveira <bristot@redhat.com>
Fixes: 8fa826b734 ("trace/hwlat: Implement the mode config option")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
