This patch (as626) makes some improvements to the debugging code in
uhci-hcd. The main change is that now the code won't get compiled if
CONFIG_USB_DEBUG isn't set. But there are other changes too, like
adding a missing .owner field and printing a debugging dump if the
controller dies.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As part of reorienting uhci-hcd away from URBs and toward endpoint
queues, this patch (as625) eliminates the driver's main list of URBs.
The list wsa used mainly in checking for URB completions; now the driver
goes through the list of active endpoints and checks the members of the
queues.
As a side effect, I had to remove the code that looks for FSBR timeouts.
For now, FSBR will remain on so long as any URBs on a full-speed control
or bulk queue request it, even if the queue isn't advancing. A later
patch can add more intelligent handling. This isn't a huge drawback;
it's pretty rare for an URB to get stuck for more than a fraction of a
second. (And it will help the people trying to use those insane HP USB
devices.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as624) fixes a hardware race in uhci-hcd by adding a dummy
TD to the end of each endpoint's queue. Without the dummy the host
controller will effectively turn off the queue when it reaches the end,
which happens asynchronously. This leads to a potential problem when
new transfer descriptors are added to the end of the queue; they may
never get used.
With a dummy TD present the controller never turns off the queue;
instead it just stops at the dummy and leaves the queue on but inactive.
When new TDs are added to the end of the queue, the first new one gets
written over the dummy. Thus there's never any question about whether
the queue is running or needs to be restarted.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as623) changes the uhci-hcd driver to make it use one QH per
device endpoint, instead of a QH per URB as it does now. Numerous areas
of the code are affected by this. For example, the distinction between
"queued" URBs and non-"queued" URBs no longer exists; all URBs belong to
a queue and some just happen to be at the queue's head.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In setting up the of PHY we masked off too many bits, instead just
initialize PORTSC for the type of PHY we are using.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a second linksys vendor-id (077b) and the product id of the
pegasus based adapter USBVPN1
http://www1.linksys.com/Products/product.asp?prid=3D543&scid=3D30
Furthermore it replaces all LINKSYS_GPIO_RESET with DEFAULT_GPIO_RESET as both
are declared like this:
#define DEFAULT_GPIO_RESET 0x24
#define LINKSYS_GPIO_RESET 0x24
This is misleading and confusing.
The check is now done via the VENDOR_ID in pegasus.c:
if (usb_dev_id[pegasus->dev_index].vendor == VENDOR_LINKSYS
Signed-off-by: Malte Doersam <mdoersam@arcor.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as628c) adds error handling to the USB HID core. When an
error is reported for an interrupt URB, the driver will do delayed
retries, at increasing intervals, for up to one second. If that doesn't
work, it will try to reset the device. Testing by users has shown that
both the retries and the resets end up getting used.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This makes usbcore use the driver model wakeup flags for host controllers
and for their root hubs. Since previous patches have removed all users of
the HCD flags they replace, this converts the last users of those flags.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This makes OHCI use the driver model wakeup control bits for its root hub
(e.g. disable on amd756, because of chip erratum) and for the controller
itself. It no longer uses the hcd glue bits with those roles, and depends
on the previous patch making the root hub available earlier.
Note that on most platforms (boot code properly setting the RWC bit) this
gives a partial workaround for the way PCI isn't currently flagging devices
that support PME# signals. (Because of odd PCI init sequencing on PPC.)
That's because many OHCI controllers support "legacy PCI PM" ... without
involving any PCI PM capability.
USB wakeup from STR, if it works on your system, may still involve
tweaking things by hand in /proc/acpi/wakeup.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make the HCD initialization sequence more sane ... notably, setting up
root hubs before HCDs are asked to do their one-time init. Among other
things, that lets the HCDs do custom root hub init along with all the
other one-time initialization done in the (now misnamed) reset() method.
This also copies the controller wakeup flags into the root hub; it's
done a bit later than would be ideal, but that'll be necessary until
the PCI code initializes them correctly. (The PCI patch breaks on PPC
due to how it sequences PCI initialization.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds declarations for three USB peripheral controllers:
- Two high speed USB cores that can be licensed from Mentor Graphics
to be integrated into silicon:
* "musbhsfc" is for peripherals only, as found in for example the
IBM/AMCC 44EP processors.
* "musbhdrc" is OTG-capable (dual role), and is found in various
products including OMAP 2430 and the new DaVinci SOCs.
The "musbh" standing for "Mentor USB Highspeed", the rest standing
for "Function Controller" or "Dual Role Controller" (OTG-capable).
- The full speed controller on the FreeScale MPC8272.
Adding these definitions just allows gadget driver code to handle any
controller-specific logic; controller drivers are quite separate.
Signed-off-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Resove a minor FIXME: don't change MTU while RNDIS link is active,
the other end won't expect such things...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds support for the USB peripheral controller on AT91
(rm9200, eventually also sam9261 or uClinux) platforms.
More SOC support for Linux-USB ... an uncomplicated pure PIO driver.
It'd be worth using this as a model, if you're starting a driver
for some other peripheral controller.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds support for OHCI on AT91rm9200 based boards.
Possibly of interest here is the way this uses <linux/clk.h> to
gate clocks on/off during system pm state transitions. That's
typical for non-PCI systems. Some can go further; Mini-A host
side connectors enable ID-pin sensing.
From: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch modifies the behavior of the EHCI driver in an unlink path
that seems to be causing various issues on some systems. Those problems
have included issues with disconnection, driver unbinding, and similar
cases where urb unlinking would just not work right.
This patch should help avoid those problems by not turning off the async
(control/bulk) schedule until it's not expecting an "async advance" IRQ,
which comes from the processing passing the schedule head. Whether the
driver attempts to do such things is dependent on system timings, so
many folk would never have seen these problems.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ALCHEMY: Add OHCI support for AU1200
Updated by moving the OHCI support out of the EHCI patch.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ALCHEMY: Add EHCI support for AU1200
Updated by removing the OHCI support
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On the MPC834x processors the multiport host (MPH) EHCI controller has an
erratum in which the port number in the queue head expects to be 0..N-1
instead of 1..N. If we are on one of these chips we subtract one from
the port number before putting it into the queue head.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adding a Host Mode USB driver for the Freescale 83xx.
This driver supports both the Dual-Role (DR) controller and the
Multi-Port-Host (MPH) controller present in the Freescale MPC8349. It has
been tested with the MPC8349CDS reference system. This driver depends on
platform support code for setting up the pins on the device package in a
manner appropriate for the board in use. Note that this patch requires
selecting the EHCI controller option under the USB Host menu.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch replaces the split ISO raw_mask calculation code in the
iso_stream_init() function that computed incorrect numbers of high
speed transactions for both input and output transfers.
In the output case, it added a superfluous start-split transaction for
all maxmimum packet sizes that are a multiple of 188.
In the input case, it forgot to add complete-split transactions for all
microframes covered by the full speed transaction, and the additional
complete-split transaction needed for the case when full speed data
starts arriving near the end of a microframe.
These changes don't affect the lack of full speed bandwidth, but at
least it removes the MMF errors that the HC raised with some input
streams.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This teaches the EHCI driver about a quirk seen in older NForce2 chips,
adding a workaround to ignore selective suspend requests. Bus-wide
(so-called "global") suspend still works, as does USB wakeup of a
root hub that's globally suspended.
There's still a hole in this support though. Strictly speaking, this
should _fail_ selective suspend requests, rather than ignoring them,
since doing it this way means that devices which should be able to issue
remote wakeup are not going to be able to do that. For now, we'll just
live with that problem ... since usbcore expects to do selective suspend
on the way towards a full bus suspend, and usbcore needs to be able to
do full bus suspend.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the patch below converts a bunch of semaphores-used-as-mutex in the USB
code to mutexes
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After the removal of usb-midi.c, there's no longer any external user of
usb_get_string().
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the obsolete USB_MIDI and USB_AUDIO drivers.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this does two things:
- use kzalloc where appropriate
- correct error return codes in ioctl
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
another one for kzalloc. This covers the storage subdirectory.
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/usb/core/devio.c: In function `usbdev_read':
drivers/usb/core/devio.c:140: error: invalid type argument of `->'
drivers/usb/core/devio.c:141: error: invalid type argument of `->'
drivers/usb/core/devio.c:142: error: invalid type argument of `->'
drivers/usb/core/devio.c:143: error: invalid type argument of `->'
Cc: Oliver Neukum <oliver@neukum.org>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this is a small optimisation. It is ridiculous to do a kmalloc for
18 bytes. This puts it onto the stack.
Signed-off-by: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a Video4Linux2 driver for ZC0301
Image Processor and Control Chip.
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a use-after-free bug in the usb-serial core. It is simple to
trigger this (open a usb-serial port, then yank the device out before
closing the port.) Thanks to Stefan Seyfried <seife@suse.de> for
reporting this, and to the slab debugging code which enabled it to be
tracked down.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a bunch of new device IDs to the ftdi_sio driver for
various devices from microHAM using FTDI chips.
Micheal Studer supplied the PID for the USB-Y9 device. I examined the
INF file in microHAM's Windows driver package for the USB-KW, USB-YS,
USB-IC, USB-DB9 and USB-RS232 devices.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added the USB vendorID of GSPDA and the productID of GSPDA's palm
smartphone 'xplore m68' to the list of known devices.
Signed-off-by: Hendrik Schweppe <linuxkpatch@hendrik.fam-schweppe.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remote NDIS response to OID_GEN_SUPPORTED_LIST only allocated space
for the data attached to the reply, and not the reply structure
itself. This caused other kmalloc'd memory to be corrupted.
Signed-off-by: Shaun Tancheff <shaun@tancheff.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is a dead lock in lh7a40x udc driver. When the driver receive a
SET_FEATURE HALT request, the dev lock is taken by the interrupt
handler lh7a40x_udc_irq then the handler will call lh7a40x_set_halt
function which in its turn will try to acquire the dev lock.
Signed-off-by: Franck Bui-Huu <franck.bui-huu@innova-card.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as656) adds an unusual_devs.h entry for the Lyra RCA RD1080
MP3 player. Its card-reader firmware has the common
report-one-too-many-sectors bug. This fixes Novell bug #152175.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is for the Dual USB Joypad [0925:8866] from Wisegroup. The
HID_QUIRK_NOGET is necessary for it to respond to input, and the
HID_QUIRK_MULTI_INPUT is necessary to have two js# nodes appear.
Signed-off-by: Andrew Fuller <mactalla.obair@gmail.com>
Cc: "Dmitry Torokhov" <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix http://bugzilla.kernel.org/show_bug.cgi?id=6128
Finish morphing the "early handoff" version of the EHCI BIOS handshake over
to match the previous implementation inside the EHCI driver (except that
now we forcibly disable the SMI). The version that had been with the PCI
code was surprisingly full of bugs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: <yazar256@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
