Add ieee80211_get_operstate() function to get the operstate
of the netdevice.
This is needed for drivers that need to know when the interface
is IF_OPER_UP (e.g. wl12xx), and block notifiers can't be used
(e.g. because the interface is already IF_OPER_UP, like after
resuming from suspend)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some old hci controllers do not accept any mask so leave the
default mask on for these devices.
< HCI Command: Set Event Mask (0x03|0x0001) plen 8
Mask: 0xfffffbff00000000
> HCI Event: Command Complete (0x0e) plen 4
Set Event Mask (0x03|0x0001) ncmd 1
status 0x12
Error: Invalid HCI Command Parameters
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Tested-by: Corey Boyle <corey@kansanian.com>
Tested-by: Ed Tomlinson <edt@aei.ca>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
shutdown should wait for SCO link to be properly disconnected before
detroying the socket, otherwise an application using the socket may
assume link is properly disconnected before it really happens which
can be a problem when e.g synchronizing profile switch.
Signed-off-by: Luiz Augusto von Dentz <luiz.dentz-von@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Some old hci controllers do not accept any mask so leave the
default mask on for these devices.
< HCI Command: Set Event Mask (0x03|0x0001) plen 8
Mask: 0xfffffbff00000000
> HCI Event: Command Complete (0x0e) plen 4
Set Event Mask (0x03|0x0001) ncmd 1
status 0x12
Error: Invalid HCI Command Parameters
Signed-off-by: Ville Tervo <ville.tervo@nokia.com>
Tested-by: Corey Boyle <corey@kansanian.com>
Tested-by: Ed Tomlinson <edt@aei.ca>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Structures "l2cap_conninfo" and "rfcomm_conninfo" have one padding
byte each. This byte in "cinfo" is copied to userspace uninitialized.
Signed-off-by: Filip Palian <filip.palian@pjwstk.edu.pl>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
shutdown should wait for SCO link to be properly disconnected before
detroying the socket, otherwise an application using the socket may
assume link is properly disconnected before it really happens which
can be a problem when e.g synchronizing profile switch.
Signed-off-by: Luiz Augusto von Dentz <luiz.dentz-von@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Enabling DEBUG_STRICT_USER_COPY_CHECKS causes the following
warning:
In function 'copy_from_user',
inlined from 'rfcomm_sock_setsockopt' at
net/bluetooth/rfcomm/sock.c:705:
arch/x86/include/asm/uaccess_64.h:65:
warning: call to 'copy_from_user_overflow' declared with
attribute warning: copy_from_user() buffer size is not provably
correct
presumably due to buf_size being signed causing GCC to fail to
see that buf_size can't become negative.
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Local busy is encoded in a bitfield, but was not masked out correctly.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
When code was moved from l2cap_core.c to l2cap_sock.c in commit
6de0702b5b, one line was dropped
from the old __l2cap_sock_close() implementation. This sk_state
change should still be in l2cap_chan_close().
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
If the link key is secure (authenticated or combination 16 digit)
the sec_level will be always BT_SECURITY_HIGH. Therefore, instead
of checking the link key type simply check the sec_level on the link.
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Add BT_POWER socket option used to control the power
characteristics of the underlying ACL link. When the remote end
has put the link in sniff mode and the host stack wants to send
data we need need to explicitly exit sniff mode to work well with
certain devices (For example, A2DP on Plantronics Voyager 855).
However, this causes problems with HID devices.
Hence, moving into active mode when sending data, irrespective
of who set the sniff mode has been made as a socket option. By
default, we will move into active mode. HID devices can set the
L2CAP socket option to prevent this from happening.
Currently, this has been implemented for L2CAP sockets. This has been
tested with incoming and outgoing L2CAP sockets for HID and A2DP.
Based on discussions on linux-bluetooth and patches submitted by
Andrei Emeltchenko.
Signed-off-by: Jaikumar Ganesh <jaikumar@google.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
As we cannot relay on a userspace mgmt api implementation we should verify
if pin_code_reply in fact contains the secure pin code.
If userspace replied with unsecure pincode when secure was required we will
send pin_code_neg_reply to the controller.
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
sparse complains about a few things that should
be static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Set the 'peer_addr_type' field of the LE Create Connection command
sent in hci_le_connect().
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Ville Tervo <ville.tervo@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
When connecting to a LE device, we need to check the advertising
cache in order to know the address type of that device.
If its advertising entry is not found, the connection is not
established and hci_connect() returns error.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Ville Tervo <ville.tervo@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
There is no need to check the connection's state since hci_conn_add()
has just created a new connection and its state has been set properly.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Ville Tervo <ville.tervo@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds a new field (dst_type) to the struct hci_conn which
holds the type of the destination address (bdaddr_t dst). This
approach is needed in order to use the struct hci_conn as an
abstraction of LE connections in HCI Layer. For non-LE this field
is ignored.
This patch also set properly the 'dst_type' field after initializing
LE hci_conn structures.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Replace if(conn) with if(!conn) checking to avoid too many nested statements
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Legacy devices don't re-authenticate the link properly if a link key
already exists. Thus, don't update sec_level for this case even if
hci_auth_complete_evt indicates success. Otherwise the sec_level will
not reflect a real security on the link.
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds a timer to clear 'adv_entries' after three minutes.
After some amount of time, the advertising entries cached during
the last LE scan should be considered expired and they should be
removed from the advertising cache.
It was chosen a three minutes timeout as an initial attempt. This
value might change in future.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The LE advertising cache should be cleared before performing a LE
scanning. This will force the cache to contain only fresh advertising
entries.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds a function to handle LE Advertising Report Meta
Events.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Anderson Briglia <anderson.briglia@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch implements the LE advertising cache. It stores sensitive
information (bdaddr and bdaddr_type so far) gathered from LE
advertising report events.
Only advertising entries from connectables devices are added to the
cache.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds definitions and a new struct for Advertising Report
Event from LE and Dual Mode controllers.
Signed-off-by: Anderson Briglia <anderson.briglia@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The call to l2cap_chan_clear_timer() is not really needed in l2cap_sock.c.
This patch also adds a call to l2cap_chan_clear_timer() to the only place
in __l2cap_sock_close() that wasn't calling it. It's safe call it there
because l2cap_chan_clear_timer() check first for timer_peding().
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The new timer does not belong to struct sock, tought it still touch some
sock things, but this will be sorted out soon.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
chan_type says if our chan is raw(direclty access to HCI),
connection less or connection oriented.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This move all the sending logic to l2cap_core.c, but we still have a
socket dependence there, struct msghdr. It will be removed in some of the
further commits.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This is actually __l2cap_sock_close() renamed to __l2cap_chan_close().
At a first look it may not make sense, but with the further cleanups that
will come it will.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The get_connections function has no need to use hci_dev_list_lock. The
code was there probably because of a copy-paste mistake.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
In L2CAP_SDU_UNSEGMENTED case, if sock_queue_rcv_skb returns error,
l2cap_ertm_reassembly_sdu should not return 0 so as to insert the
skb into BUSY_QUEUE for later retries.
Signed-off-by: Ruiyi Zhang <Ruiyi.Zhang@Atheros.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
We use priv->mutex to avoid race conditions between chswitch_done()
and mac_channel_switch(), when marking channel switch in
progress. But chswitch_done() can be called in atomic context
from rx_csa() or with mutex already taken from commit_rxon().
To fix remove mutex from chswitch_done() and use atomic bitops
for marking channel switch pending.
Cc: stable@kernel.org # 2.6.39+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ignacy reports that sometimes after leaving an IBSS
joining a new one didn't work because there still
were stations on the list. He fixed it by flushing
stations when attempting to join a new IBSS, but
this shouldn't be happening in the first case. When
I looked into it I saw a race condition in teardown
that could cause stations to be added after flush,
and thus cause this situation. Ignacy confirms that
after applying my patch he hasn't seen this happen
again.
Reported-by: Ignacy Gawedzki <i@lri.fr>
Debugged-by: Ignacy Gawedzki <i@lri.fr>
Tested-by: Ignacy Gawedzki <i@lri.fr>
Cc: stable@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During channge channel, tx power will not send to uCode, the tx power command
should send after scan complete. but should also can send after RXON command.
Stable fix identified by Stanislaw Gruszka <sgruszka@redhat.com>.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Cc: stable@kernel.org [2.6.38+]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Padding per MSDU will affect the length of next packet and hence
the exact length of next packet is uncertain here.
Also, aggregation of transmission buffer, while downloading the
data to the card, wont gain much on the AMSDU packets as the AMSDU
packets utilizes the transmission buffer space to the maximum
(adapter->tx_buf_size).
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All MSDUs, except the last one in an AMSDU, should end up at 4
bytes boundary. There is need to check if enough skb_tailroom
space exists before padding the skb.
Also re-arranging code for better readablity.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The check of skb list empty before calling skb_peek and skb_dequeue is
redundant. These functions returns NULL if the list is empty.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of counting the number of packets in txq
for particular RA list before AMSDU creation,
maintain a counter which will keep track of the
same.
This will reduce some MIPS while generating AMSDU
traffic as we only have to check the counter instead
of traversing through skb list.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
