Modify clock division displaying in debugfs for matching
the new CLKDIV,CLKODD user interface arrangement.
Is using the has_odd_clk_div property to choose the proper format.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Setting host->data to NULL is incorrect sequence in STATE_SENDING_STOP
state of FSM: This early setting leads to the skip of dma_unmap_sg()
in atmci_dma_cleanup() which is a bug.
Idea taken from dw_mmc by Seungwon Jeon.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The use of DMA slave config operation requires that the burst size
(aka chunk size) is specified through this interface.
Modify atmel-mci slave driver to use this specification on its side.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The data timeout timer was configured after mmc_add_host call. So, with bad
timings, it was possible to have a mmc request causing mod_timer call on a
non setup timer.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The state machine use in atmel-mci can't work with old IP versions
(< 0x200). This patch allows to have a common state machine for all
versions in order to remove at91-mci driver only used for old versions.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
First mci IPs (mainly on rm9200 and 9261) don't have the r/w proof
capability. The driver didn't work correctly without this capability
in PDC mode because of the double buffer switch which is too slow
even if we stop the transfer to perform this switch.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add an odd clock divider capability available from v5xx. It also involves
changing the clock divider calculation, and changing the switch-case
statement to use top-down fallthrough.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The HSMCI operates at a rate of up to Master Clock divided by two.
Moreover previous calculation can cause overflows and so wrong
timeouts.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Pull slave-dmaengine update from Vinod Koul:
"This includes the cookie cleanup by Russell, the addition of context
parameter for dmaengine APIs, more arm dmaengine driver cleanup by
moving code to dmaengine, this time for imx by Javier and pl330 by
Boojin along with the usual driver fixes."
Fix up some fairly trivial conflicts with various other cleanups.
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (67 commits)
dmaengine: imx: fix the build failure on x86_64
dmaengine: i.MX: Fix merge of cookie branch.
dmaengine: i.MX: Add support for interleaved transfers.
dmaengine: imx-dma: use 'dev_dbg' and 'dev_warn' for messages.
dmaengine: imx-dma: remove 'imx_dmav1_baseaddr' and 'dma_clk'.
dmaengine: imx-dma: remove unused arg of imxdma_sg_next.
dmaengine: imx-dma: remove internal structure.
dmaengine: imx-dma: remove 'resbytes' field of 'internal' structure.
dmaengine: imx-dma: remove 'in_use' field of 'internal' structure.
dmaengine: imx-dma: remove sg member from internal structure.
dmaengine: imx-dma: remove 'imxdma_setup_sg_hw' function.
dmaengine: imx-dma: remove 'imxdma_config_channel_hw' function.
dmaengine: imx-dma: remove 'imxdma_setup_mem2mem_hw' function.
dmaengine: imx-dma: remove dma_mode member of internal structure.
dmaengine: imx-dma: remove data member from internal structure.
dmaengine: imx-dma: merge old dma-v1.c with imx-dma.c
dmaengine: at_hdmac: add slave config operation
dmaengine: add context parameter to prep_slave_sg and prep_dma_cyclic
dmaengine/dma_slave: introduce inline wrappers
dma: imx-sdma: Treat firmware messages as warnings instead of erros
...
Add inline wrappers for device_prep_slave_sg() and device_prep_dma_cyclic()
interfaces to hide new parameter from current users of affected interfaces.
Convert current users to use new wrappers instead of direct calls.
Suggested by Russell King [https://lkml.org/lkml/2012/2/3/269].
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Some callbacks are set too early -- i.e. we can have dma capabilities but
we can't get a dma channel. So wait to get the dma channel before setting
callbacks and change logs consequently.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
[Should be applied to 3.2-stable.]
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
There are few existing user drivers of dw_dmac. They will break as soon as we
remove unused fields from struct dw_dma_slave. This patch focuses to fix these
user drivers to use dma_slave_config() routine.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Sometimes a software reset is needed. Then some registers are saved and
restored but the interrupt mask register is missing. It causes issues
with sdio devices whose interrupts are masked after reset.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
fixup usage of dma direction by introducing dma_transfer_direction,
this patch moves mmc drivers to use new enum
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This patch fixes a potential issue about PDC interrupts. For example we
have a ENDRX pending interrupt and a RXBUFF pending interrupt. We have
received the RXBUFF interrupt but the transfer is not finished (so we
didn't have time to give a new buffer to the PDC controller). Then we
will compute ENDRX interrupt and we will give a new buffer to the PDC
controller, just after we will compute the RXBUFF interrupt and give
one or two new buffers to the PDC controller but we are not sure that
the first buffer given has been filled. So in this situation we may
have "lost" one sg buffer. It's the same for transmission.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Assuming that a sg buffer size is a page size is false so use sg_dma_len.
A 4096 bytes can be required with two 2048-bytes sg buffer.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Rename atmci_start_command() to atmci_send_command() which is more
appropriate; atmci_start_command suggests we're sending a start command.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add pdc support for atmel-mci. It makes at91-mci driver useless because it
was only used for the old atmel MCI core which has pdc but no dma support.
To allow removing at91-mci, the capabilities of the MCI core are detected
at runtime -- then the driver will use pio, pdc or dma transfers.
Warning: at91rm9200 is not supported, to support it we need to use swab32
on data but I have no board to test it.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Change atmci_readl and atmci_writel macros: remove string concatenation.
We can use these macros with registers which are not prefixed by ATMCI_.
This is the case if we want to write PDC registers which are common to
several devices so they are not prefixed with ATMCI_.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Take care of slots while going to suspend state.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use the new dmaengine helpers to make the code more readable.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fixes the following:
- It is perfectly legal for the dma_map_sg() to return fewer
entries than were passed in.
- Supply the returned numer of (possibly coalesced) entries to
the device_pre_slave_sg() function.
- Use the proper original sg_len when unmapping the sglist
in the error path.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
As established for the MMCI, it is proper to map the DMA buffers
on the DMA engine which is the one actually performing the DMA.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Based on report made by Yauhen in:
"MMC: Fix multiblock SDIO transfers in AT91 MCI" patch,
I report those changes to the brother driver: atmel-mci.
So, this patch sets SDIO transfer types: SDIO block and SDIO byte
transfers instead of using ordinary MMC block transfers.
It is checking opcode for SDIO CMD53 and setting transfer
type in MCI_CMDR register properly.
Reported-by: Yauhen Kharuzhy <yauhen.kharuzhy@promwad.com>
Cc: <stable@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
We have deprecated the distinction between hardware and physical
segments in the block layer. Consolidate the two limits into one in
drivers/mmc/.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
[cjb: rebased patch against Linus]
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Atmel-mci support for SDIO interrupts. This adds the enable_sdio_irq()
function and the configuration of sdio irq mask per slot. With this irq
mask information, we keep the idea of multiple slot per sd/mmc host (not
only A and B). MMC_CAP_SDIO_IRQ is added according to slot configuration.
A new little function is added to run mmc_signal_sdio_irq() during
interrupt handling routine.
Signed-off-by: Anders Grahn <anders.grahn@hd-wireless.se>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enable high speed support for atmel-mci driver. This support is dependent
of the revision of the IP and, of course, the capacity of the SD card
used.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Maciej Sosnowski <maciej.sosnowski@intel.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
DMAENGINE: extend the control command to include an arg
async_tx: trim dma_async_tx_descriptor in 'no channel switch' case
DMAENGINE: DMA40 fix for allocation of logical channel 0
DMAENGINE: DMA40 support paused channel status
dmaengine: mpc512x: Use resource_size
DMA ENGINE: Do not reset 'private' of channel
ioat: Remove duplicated devm_kzalloc() calls for ioatdma_device
ioat3: disable cacheline-unaligned transfers for raid operations
ioat2,3: convert to producer/consumer locking
ioat: convert to circ_buf
DMAENGINE: Support for ST-Ericssons DMA40 block v3
async_tx: use of kzalloc/kfree requires the include of slab.h
dmaengine: provide helper for setting txstate
DMAENGINE: generic channel status v2
DMAENGINE: generic slave control v2
dma: timb-dma: Update comment and fix compiler warning
dma: Add timb-dma
DMAENGINE: COH 901 318 fix bytesleft
DMAENGINE: COH 901 318 rename confusing vars
This adds an argument to the DMAengine control function, so that
we can later provide control commands that need some external data
passed in through an argument akin to the ioctl() operation
prototype.
[dan.j.williams@intel.com: fix up some missed conversions]
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
In debugfs, printing of command response reports resp[2] twice: fix it to
resp[3].
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Disable data error interrupts while we are actually recording that there
is not such errors. This will prevent, in some cases, the warning message
printed at new request queuing (in atmci_start_request()).
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The removing of an SD card in certain circumstances can lead to a kernel
oops if we do not make sure that the "data" field of the host structure is
valid. This patch adds a test in atmci_dma_cleanup() function and also
calls atmci_stop_dma() before throwing away the reference to data.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Two parameters were swapped in the calls to atmci_init_slot().
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reported-by: Anders Grahn <anders.grahn@hd-wireless.se>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Convert the device_terminate_all() operation on the
DMA engine to a generic device_control() operation
which can now optionally support also pausing and
resuming DMA on a certain channel. Implemented for the
COH 901 318 DMAC as an example.
[dan.j.williams@intel.com: update for timberdale]
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Maciej Sosnowski <maciej.sosnowski@intel.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Li Yang <leoli@freescale.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Magnus Damm <damm@opensource.se>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Joe Perches <joe@perches.com>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This new revision of the IP adds some improvements to the MCI already
present in several Atmel SOC.
Some new registers are added and a particular way of handling DMA
interaction lead to a new sequence in function call which is backward
compatible: On MCI2, we must set the DMAEN bit to enable the DMA
handshaking interface. This must happen before the data transfer command
is sent.
A new function is able to differentiate MCI2 code and is based on
knowledge of processor id (cpu_is_xxx()).
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow the use of another DMA controller driver in atmel-mci sd/mmc driver.
This adds a generic dma_slave pointer to the mci platform structure where
we can store DMA controller information. In atmel-mci we use information
provided by this structure to initialize the driver (with new helper
functions that are architecture dependant).
This also adds at32/avr32 chip modifications to cope with this new access
method.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://neil.brown.name/md: (97 commits)
md: raid-1/10: fix RW bits manipulation
md: remove unnecessary memset from multipath.
md: report device as congested when suspended
md: Improve name of threads created by md_register_thread
md: remove sparse warnings about lock context.
md: remove sparse waring "symbol xxx shadows an earlier one"
async_tx/raid6: add missing dma_unmap calls to the async fail case
ioat3: fix uninitialized var warnings
drivers/dma/ioat/dma_v2.c: fix warnings
raid6test: fix stack overflow
ioat2: clarify ring size limits
md/raid6: cleanup ops_run_compute6_2
md/raid6: eliminate BUG_ON with side effect
dca: module load should not be an error message
ioat: driver version 4.0
dca: registering requesters in multiple dca domains
async_tx: remove HIGHMEM64G restriction
dmaengine: sh: Add Support SuperH DMA Engine driver
dmaengine: Move all map_sg/unmap_sg for slave channel to its client
fsldma: Add DMA_SLAVE support
...
Unification of the atmel-mci driver to support the AT91 processors MCI
interface. The atmel-mci driver currently supports the AVR32 and this
patch adds AT91 support.
Add read/write proof selection switch dependent on chip availability of
this feature.
To use this new driver on a at91 the platform driver for your board needs
to be updated.
[nicolas.ferre@atmel.com indent, Kconfig comment and one printk modification]
Signed-off-by: Rob Emanuele <rob@emanuele.us>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
