* acpi-scan:
ACPI: Add _DEP support to fix battery issue on Asus T100TA
* acpi-pm:
ACPI / sleep: Drain outstanding events after disabling multiple GPEs
ACPI / PM: Fixed a typo in a comment
* acpi-lpss:
dmaengine: dw: enable runtime PM
ACPI / LPSS: introduce a 'proxy' device to power on LPSS for DMA
ACPI / LPSS: allow to use specific PM domain during ->probe()
ACPI / LPSS: add all LPSS devices to the specific power domain
* acpi-processor:
ACPI / cpuidle: avoid assigning signed errno to acpi_status
ACPI / processor: remove unused variabled from acpi_processor_power structure
ACPI / processor: Update the comments in processor.h
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so some #ifdef blocks
depending on CONFIG_PM_RUNTIME may be dropped now.
Do that in drivers/i2c/busses/i2c-omap.c.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Cadence I2C controller has bug wherein it generates invalid read transactions
after timeout in master receiver mode. This driver does not use the HW
timeout and this interrupt is disabled but the feature itself cannot be
disabled. Hence, this patch writes the maximum value (0xFF) to this register.
This is one of the workarounds to this bug and it will not avoid the issue
completely but reduces the chances of error.
Signed-off-by: Vishnu Motghare <vishnum@xilinx.com>
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
According to I2C specification the NACK should be handled as follows:
"When SDA remains HIGH during this ninth clock pulse, this is defined as the Not
Acknowledge signal. The master can then generate either a STOP condition to
abort the transfer, or a repeated START condition to start a new transfer."
[I2C spec Rev. 6, 3.1.6: http://www.nxp.com/documents/user_manual/UM10204.pdf]
Currently the Davinci i2c driver interrupts the transfer on receipt of a
NACK but fails to send a STOP in some situations and so makes the bus
stuck until next I2C IP reset (idle/enable).
For example, the issue will happen during SMBus read transfer which
consists from two i2c messages write command/address and read data:
S Slave Address Wr A Command Code A Sr Slave Address Rd A D1..Dn A P
<--- write -----------------------> <--- read --------------------->
The I2C client device will send NACK if it can't recognize "Command Code"
and it's expected from I2C master to generate STP in this case.
But now, Davinci i2C driver will just exit with -EREMOTEIO and STP will
not be generated.
Hence, fix it by generating Stop condition (STP) always when NACK is received.
This patch fixes Davinci I2C in the same way it was done for OMAP I2C
commit cda2109a26 ("i2c: omap: query STP always when NACK is received").
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reported-by: Hein Tibosch <hein_tibosch@yahoo.es>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Switch Davinci I2C driver to use platform_get_irq(), because
it is not recommened to use platform_get_resource(pdev, IORESOURCE_IRQ, ..)
for requesting IRQ resources any more, as they can be not ready yet
in case of DT-boot.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We can simply pass the pointer to the private structure to the irq
routine instead of passing the platform device and looking up its
driver_data.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The SET_PM_RUNTIME_PM_OPS() and SET_RUNTIME_PM_OPS() macros are
identical except that one of them is not empty for CONFIG_PM set,
while the other one is not empty for CONFIG_PM_RUNTIME set,
respectively.
However, after commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if
PM_SLEEP is selected) PM_RUNTIME is always set if PM is set, so one
of these macros is now redundant.
For this reason, replace SET_PM_RUNTIME_PM_OPS() with
SET_RUNTIME_PM_OPS() everywhere and redefine the SET_PM_RUNTIME_PM_OPS
symbol as SET_RUNTIME_PM_OPS in case new code is starting to use the
macro being removed here.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add support for SCCB by implementing I2C_M_IGNORE_NAK and I2C_M_STOP
flags and advertising functionality flag I2C_FUNC_PROTOCOL_MANGLING.
Also fixed missing functionality flag I2C_FUNC_NOSTART.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 0f5768bf89 ("i2c: omap: implement workaround for handling
invalid BB-bit values") introduce the error result in boot test fault on
OMAP3530 boards.
The patch fix the error (disable i2c bus test for OMAP3530).
Reported-by: Kevin Hilman <khilman@kernel.org>
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Fixes: 0f5768bf89 ("i2c: omap: implement workaround for handling invalid BB-bit values")
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
CONFIG_OF_DYNAMIC enables runtime changes to the device tree which in
turn may trigger addition or removal of devices from Linux. Add an
OF_RECONFIG notifier handler to receive tree change events and to
creating or destroy i2c devices as required.
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
[grant.likely: clean up #ifdefs and drop unneeded error handling]
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-i2c@vger.kernel.org
Dynamically inserting i2c client device nodes requires the use
of a single device registration method. Factor out the loop body of
of_i2c_register_devices() so that it can be called for individual
device_nodes instead of for all the children of a node.
Note: The diff of this commit looks far more complicated than it
actually is due the indentation being changed for a large block of code.
When viewed using the diff -w flag to ignore whitespace changes it can
be seen that the change is actually quite simple.
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
[grant.likely: Made new function static and removed changes to header]
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-i2c@vger.kernel.org
Let's handle i2c interrupt re-configuration in i2c driver. This will
help us in removing some soc specific checks from machine files and
will help in removing static iomapping of SYS register in exynos.c
Also handle saving and restoring of SYS_I2C_CFG register during
suspend and resume of i2c driver.
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Now that we are using the clk notifier framework we get compile errors
without COMMON_CLK. But the driver fails to probe without COMMON_CLK
anyways, so just add that as a Kconfig dependency.
Signed-off-by: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
ACPI 5.0 introduces _DEP (Operation Region Dependencies) to designate
device objects that OSPM should assign a higher priority in start
ordering due to future operation region accesses.
On Asus T100TA, ACPI battery info are read from a I2C slave device via
I2C operation region. Before I2C operation region handler is installed,
battery _STA always returns 0. There is a _DEP method of designating
start order under battery device node.
This patch is to implement _DEP feature to fix battery issue on the
Asus T100TA. Introducing acpi_dep_list and adding dep_unmet count
in struct acpi_device. During ACPI namespace scan, create struct
acpi_dep_data for a valid pair of master (device pointed to by _DEP)/
slave(device with _DEP), record master's and slave's ACPI handle in
it and put it into acpi_dep_list. The dep_unmet count will increase
by one if there is a device under its _DEP. Driver's probe() should
return EPROBE_DEFER when find dep_unmet is larger than 0. When I2C
operation region handler is installed, remove all struct acpi_dep_data
on the acpi_dep_list whose master is pointed to I2C host controller
and decrease slave's dep_unmet. When dep_unmet decreases to 0, all
_DEP conditions are met and then do acpi_bus_attach() for the device
in order to resolve battery _STA issue on the Asus T100TA.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=69011
Tested-by: Jan-Michael Brummer <jan.brummer@tabos.org>
Tested-by: Adam Williamson <adamw@happyassassin.net>
Tested-by: Michael Shigorin <shigorin@gmail.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
No functional changes.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Arbitration Lost is an expected situation in a multimaster
environment. I2C controller (IP) correctly detect and report AL.
The only one visible reason for resetting IP in the AL case is
to avoid advisory 1.94 (omap3) and errata i595 (omap4): "I2C:
After an Arbitration is Lost the Module Incorrectly Starts
the Next Transfer".
Errata workaround states: "The MST and STT bits inside I2C_CON
should be set to 1 at the same moment (avoid setting the MST bit
to 1 while STT = 0)." The driver never set MST and STT bits
separately and doesn't create condition for errata. So the reset
is not necessary.
Also corrected return value for AL to -EAGAIN.
Tested on Beagleboard XM C.
Tested on BBB and AM437x Starter Kit by Felipe Balbi.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In a multimaster environment, after IP software reset, BB-bit value doesn't
correspond to the current bus state. It may happen what BB-bit will be 0,
while the bus is busy due to another I2C master activity.
Any transfer started when BB=0 and bus is busy wouldn't be completed by IP
and results in controller timeout. More over, in some cases IP could
interrupt another master's transfer and corrupt data on wire.
The commit implement method allowing to prevent IP from entering into
"controller timeout" state and from "data corruption" state.
The one drawback is the need to wait for 10ms before the first transfer.
Tested on Beagleboard XM C.
Tested on BBB and AM437x Starter Kit by Felipe Balbi.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Delete STAT_AD0 mask as unrelated to current IP (omap1?).
Delete DEBUG conditional around SYSTEST masks group.
Add SYSTEST functional mode masks for SCL and SDA.
Add STAT_BF mask.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c input clock can change dynamically, e.g. on the RK3066 where
pclk_i2c0 and pclk_i2c1 are connected to the armclk, which changes
rate on cpu frequency scaling.
Until now, we incorrectly called clk_get_rate() while holding the
i2c->lock in rk3x_i2c_xfer() to adapt to clock rate changes.
Thanks to Huang Tao for reporting this issue.
Do it properly now using the clk notifier framework. The callback
logic was taken from i2c-cadence.c.
Also rename all misleading "i2c_rate" variables to "clk_rate", as they
describe the *input* clk rate.
Signed-off-by: Max Schwarz <max.schwarz@online.de>
Tested-by: Doug Anderson <dianders@chromium.org> on RK3288
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
commit 6d9939f651 (i2c: omap: split out [XR]DR
and [XR]RDY) changed the way how errata i207 (I2C: RDR Flag May Be Incorrectly
Set) get handled. 6d9939f651 code doesn't correspond to workaround provided by
errata.
According to errata ISR must filter out spurious RDR before data read not after.
ISR must read RXSTAT to get number of bytes available to read. Because RDR
could be set while there could no data in the receive FIFO.
Restored pre 6d9939f651 way of handling errata.
Found by code review. Real impact haven't seen.
Tested on Beagleboard XM C.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Fixes: 6d9939f651 i2c: omap: split out [XR]DR and [XR]RDY
Tested-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since at91sam9g45 is now DT-only, all DMA capable users of this driver
are using the DT case, and the legacy support can be removed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If the Designware core is configured with IC_EMPTYFIFO_HOLD_MASTER_EN
set to zero, allowing the TX FIFO to become empty causes a STOP
condition to be generated on the I2C bus. If the transmit FIFO
threshold is set too high, an erroneous STOP condition can be
generated on long transfers - particularly where the interrupt
latency is extended.
Signed-off-by: Andrew Jackson <Andrew.Jackson@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
commit 1d7afc9594 (i2c: omap: ack IRQ in parts)
changed the interrupt handler to complete transfers without clearing
XRDY (AL case) and ARDY (NACK case) flags. XRDY or ARDY interrupts will be
fired again. As a result, ISR keep processing transfer after it was already
complete (from the driver code point of view).
A didn't see real impacts of the 1d7afc9, but it is really bad idea to
have ISR running on user data after transfer was complete.
It looks, what 1d7afc9 violate TI specs in what how AL and NACK should be
handled (see Note 1, sprugn4r, Figure 17-31 and Figure 17-32).
According to specs (if I understood correctly), in case of NACK and AL driver
must reset NACK, AL, ARDY, RDR, and RRDY (Master Receive Mode), and
NACK, AL, ARDY, and XDR (Master Transmitter Mode).
All that is done down the code under the if condition:
if (stat & (OMAP_I2C_STAT_ARDY | OMAP_I2C_STAT_NACK | OMAP_I2C_STAT_AL)) ...
The patch restore pre 1d7afc9 logic of handling NACK and AL interrupts, so
no interrupts is fired after ISR informs the rest of driver what transfer
complete.
Note: instead of removing break under NACK case, we could just replace 'break'
with 'continue' and allow NACK transfer to finish using ARDY event. I found
that NACK and ARDY bits usually set together. That case confirm TI wiki:
http://processors.wiki.ti.com/index.php/I2C_Tips#Detecting_and_handling_NACK
In order if someone interested in the event traces for NACK and AL cases,
I sent them to mailing list.
Tested on Beagleboard XM C.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Fixes: 1d7afc9 i2c: omap: ack IRQ in parts
Cc: <stable@vger.kernel.org> # v3.7+
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This fixes the following kbuild test robot warning:
>> drivers/i2c/busses/i2c-dln2.c:70:1-4: WARNING: end returns can be simplified if negative or 0 value
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It should be the DMA device, not the platform device.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The SCB is present on IMG SoCs other than the META-based TZ1090,
such as the MIPS-based Pistachio SoC. Relax the Kconfig dependency
so that it can be built on any MIPS or META machine.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This is a driver for the I2C controller found in Amlogic Meson SoCs.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This makes the topology clearer. For instance, by adding a pca9547
device with address 0x70 to bus i2c-0, you get:
/sys/class/i2c-dev/i2c-0/device/0-0070/channel-0 -> i2c-1
...
/sys/class/i2c-dev/i2c-0/device/0-0070/channel-7 -> i2c-8
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
[wsa: simplified sysfs-usage and fixed format string usage]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Martin Belanger <martin.belanger@cyaninc.com>
Acked-by: Danielle Costantino <danielle.costantino@gmail.com>
The current implementation creates muxed i2c-<n> busses as immediate
children of their i2c-<n> parent bus. In case of multiple muxes on one
bus, it is impossible to determine which muxed bus comes from which mux.
It could be argued that the parent device should be changed from the
parent adapter to the mux device. This has pros and cons. To improve the
topology, simply add a "mux_device" symlink pointing to the actual
muxing device, so we can distinguish muxed busses. Doing it this way, we
don't break the ABI.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Guenter Roeck <linux@roeck-us.net>
No need to initialize 'ret' if it gets assigned directly after that.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Add dma support for i2c. This function depend on DMA driver.
You can turn on it by write both the dmas and dma-name properties in dts node.
DMA is optional, even DMA request unsuccessfully, i2c can also work well.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If the inlcude headers aren't sorted alphabetically, then the
logical choice is to append new ones, however that creates a
lot of potential for conflicts or duplicates because every change
will then add new includes in the same location.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since commit 2fd36c5526 ("i2c: core: Map OF IRQ at probe time"),
i2c slaves without interrupts (e.g. da9210 and at24 on r8a7791/koelsch)
fail to probe:
at24: probe of 2-0050 failed with error -22
da9210: probe of 6-0068 failed with error -22
This happens because the call to of_irq_get() in i2c_device_probe()
returns -EINVAL.
If a device node does not have an "interrupts" property,
of_irq_parse_one() fails. Unlike irq_of_parse_and_map(), of_irq_get()
does not ignore errors from of_irq_parse_one(), but forwards them.
Make i2c_device_probe() ignore all errors but -EPROBE_DEFER to fix this,
just like platform_get_irq() and platform_get_irq_byname() already do.
Fixes: 2fd36c5526 ("i2c: core: Map OF IRQ at probe time")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for the IMG I2C Serial Control Bus (SCB) found on the
Pistachio and TZ1090 SoCs.
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
[Ezequiel: code cleaning and rebasing]
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver tried to access device registers with the (little-endian)
iowrite/ioread functions. While this worked on little-endian machines
(e.g. Microblaze with AXI bus), it made the driver unusable on
big-endian machines (e.g. PPC405 with PLB).
During the probe function, the driver tried to write a 32-bit reset mask
into the reset register. This caused an error interrupt on big-endian
systems, because the device detected an invalid (byte-swapped) reset
mask. The result was an Oops.
The patch implements an endianness detection similar to the one used in
other Xilinx drivers like drivers/spi/spi-xilinx.c. It was tested on a
PPC405/PLB system.
Signed-off-by: Thomas Gessler <Thomas.Gessler@exp2.physik.uni-giessen.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
No user needs magic hex values, makes this debug output. Add DMA info.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make it possible to transfer i2c message buffers via DMA.
Start/Stop/Sending_Slave_Address is still handled using the old state
machine, it is sending the actual data that is done via DMA. This is
least intrusive and allows us to work with the message buffers directly
instead of preparing a custom buffer which involves copying the data
around.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
[wsa: fixed an uninitialized var problem]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Improves readability and reduces chances of duplicates.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Amend the at91 i2c pin controller to set the state of the pins to:
- "default" on resume.
- "sleep" on suspend().
This should make it possible to optimize energy usage for the pins
both for the suspend/resume cycle
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch enforces correct I2C error returned codes from Freescale's
MPC i2c bus driver, allowing for proper user-space/kernel error
handling.
Signed-off-by: Danielle Costantino <danielle.costantino@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Don't log the host status register value in i801_isr(), it has very
little value and fills up the log when debugging is enabled.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is a control bit in the PCI configuration space which disables
interrupts. If this bit is set, the driver should not try to make use
of interrupts, it won't receive any.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c-i801 driver can work without interrupts, so there is no reason
to make a request_irq failure fatal. Instead we can simply fallback
to polling.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some systems have been reported to have trouble with interrupts. Use
wait_event_timeout() instead of wait_event() so we don't get stuck in
that case, and log the problem.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds support for the Diolan DLN-2 I2C master module. Due
to hardware limitations it does not support SMBUS quick commands.
Information about the USB protocol interface can be found in the
Programmer's Reference Manual [1], see section 6.2.2 for the I2C
master module commands and responses.
[1] https://www.diolan.com/downloads/dln-api-manual.pdf
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Johan Hovold <johan@kernel.org>
[Lee: Fixed some whitespace issues in Kconfig]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
As show in I2C specification:
- Standard-mode: the minimum HIGH period of the scl clock is 4.0us
the minimum LOW period of the scl clock is 4.7us
- Fast-mode: the minimum HIGH period of the scl clock is 0.6us
the minimum LOW period of the scl clock is 1.3us
I have measured i2c SCL waveforms in fast-mode by oscilloscope
on rk3288-pinky board. the LOW period of the scl clock is 1.3us.
It is so critical that we must adjust LOW division to increase
the LOW period of the scl clock.
Thanks Doug for the suggestion about division formulas.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When a signal is caught while the i2c-davinci bus driver is
transferring, the driver just "abandons" the transfer and leaves the
controller to fend for itself. The next I2C transaction will find the
controller in an undefined state and often results in a stream of
"initiating i2c bus recovery" messages until the controller arrives in a
defined state. This behaviour also sends out "half" or possibly even
mixed messages to I2C client devices which may put them in an undesired
state as well. So, let's get simply uninterruptible.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Drivers should put the device into low power states proactively whenever the
device is not in use. Thus implement support for runtime PM and use the
autosuspend feature to make sure that we can still perform well in case we see
lots of i2c traffic within short period of time.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C clients instantiated from OF get their IRQ mapped at device
registration time. This leads to the IRQ being silently ignored if the
related irqchip hasn't been proved yet.
Fix this by moving IRQ mapping at probe time using of_get_irq(). The
function operates as irq_of_parse_and_map() but additionally returns
-EPROBE_DEFER if the irqchip isn't available, allowing us to defer I2C
client probing.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for r8a73a4 (R-Mobile APE6) and sh73a0 (SH-Mobile AG5).
On these SoCs, the operating clock runs faster that on previous SoCs,
and the internal SCL clock counter gets incremented every 2 clocks of
the operating clock, just like on R-Car Gen2.
Cfr. the "/2" in the calculation of ICCL/ICCH in section "I2C Bus
Interface (IIC)", subsection "Transfer Rate" of the datasheets.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
According to Documentation/CodingStyle - Chapter 14:
"The preferred form for passing a size of a struct is the following:
p = kmalloc(sizeof(*p), ...);
The alternative form where struct name is spelled out hurts readability and
introduces an opportunity for a bug when the pointer variable type is changed
but the corresponding sizeof that is passed to a memory allocator is not."
So do it as recommeded.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Clients instantiated from OF get an IRQ mapping created at device
registration time. Dispose the mapping when the client is removed.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
iowait is for blkio [1]. I2C shouldn't use it.
[1] https://lkml.org/lkml/2014/11/3/317
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: stable@kernel.org
Pull i2c updates from Wolfram Sang:
"Highlights from the I2C subsystem for 3.18:
- new drivers for Axxia AM55xx, and Hisilicon hix5hd2 SoC.
- designware driver gained AMD support, exynos gained exynos7 support
The rest is usual driver stuff. Hopefully no lowlights this time"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i801: Add Device IDs for Intel Sunrise Point PCH
i2c: hix5hd2: add i2c controller driver
i2c-imx: Disable the clock on probe failure
i2c: designware: Add support for AMD I2C controller
i2c: designware: Rework probe() to get clock a bit later
i2c: designware: Default to fast mode in case of ACPI
i2c: axxia: Add I2C driver for AXM55xx
i2c: exynos: add support for HSI2C module on Exynos7
i2c: mxs: detect No Slave Ack on SELECT in PIO mode
i2c: cros_ec: Remove EC_I2C_FLAG_10BIT
i2c: cros-ec-tunnel: Add of match table
i2c: rcar: remove sign-compare flaw
i2c: ismt: Use minimum descriptor size
i2c: imx: Add arbitration lost check
i2c: rk3x: Remove unlikely() annotations
i2c: rcar: check for no IRQ in rcar_i2c_irq()
i2c: rcar: make rcar_i2c_prepare_msg() *void*
i2c: rcar: simplify check for last message
i2c: designware: add support of platform data to set I2C mode
i2c: designware: add support of I2C standard mode
This patch adds the I2C/SMBus Device IDs for the Intel Sunrise Point PCH.
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C drivers for hix5hd2 soc series, including following chipset
Hi3716CV200, Hi3719CV100, Hi3718CV100, Hi3719MV100, Hi3718MV100.
Signed-off-by: Wei Yan <sledge.yanwei@huawei.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
[wsa: folded dt docs into this patch]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- DT clean-ups in da9055-core, max14577, rn5t618, arizona, hi6421, stmpe, twl4030
- Export symbols for use in modules in max14577
- Plenty of static code analysis/Coccinelle fixes throughout the SS
- Regmap clean-ups in arizona, wm5102, wm5110, da9052, tps65217, rk808
- Remove unused/duplicate code in da9052, 88pm860x, ti_ssp, lpc_sch, arizona
- Bug fixes in ti_am335x_tscadc, da9052, ti_am335x_tscadc, rtsx_pcr
- IRQ fixups in arizona, stmpe, max14577
- Regulator related changes in axp20x
- Pass DMA coherency information from parent => child in MFD core
- Rename DT document files for consistency
- Add ACPI support to the MFD core
- Add Andreas Werner to MAINTAINERS for MEN F21BMC
New drivers/supported devices:
- New driver for MEN 14F021P00 Board Management Controller
- New driver for Ricoh RN5T618 PMIC
- New driver for Rockchip RK808
- New driver for HiSilicon Hi6421 PMIC
- New driver for Qualcomm SPMI PMICs
- Add support for Intel Braswell in lpc_ich
- Add support for Intel 9 Series PCH in lpc_ich
- Add support for Intel Quark ILB in lpc_sch
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xxsZ
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Changes to existing drivers:
- DT clean-ups in da9055-core, max14577, rn5t618, arizona, hi6421, stmpe, twl4030
- Export symbols for use in modules in max14577
- Plenty of static code analysis/Coccinelle fixes throughout the SS
- Regmap clean-ups in arizona, wm5102, wm5110, da9052, tps65217, rk808
- Remove unused/duplicate code in da9052, 88pm860x, ti_ssp, lpc_sch, arizona
- Bug fixes in ti_am335x_tscadc, da9052, ti_am335x_tscadc, rtsx_pcr
- IRQ fixups in arizona, stmpe, max14577
- Regulator related changes in axp20x
- Pass DMA coherency information from parent => child in MFD core
- Rename DT document files for consistency
- Add ACPI support to the MFD core
- Add Andreas Werner to MAINTAINERS for MEN F21BMC
New drivers/supported devices:
- New driver for MEN 14F021P00 Board Management Controller
- New driver for Ricoh RN5T618 PMIC
- New driver for Rockchip RK808
- New driver for HiSilicon Hi6421 PMIC
- New driver for Qualcomm SPMI PMICs
- Add support for Intel Braswell in lpc_ich
- Add support for Intel 9 Series PCH in lpc_ich
- Add support for Intel Quark ILB in lpc_sch"
[ Delayed to after the poweer/reset pull due to Kconfig problems with
recursive Kconfig select/depends-on chains. - Linus ]
* tag 'mfd-for-linus-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (79 commits)
mfd: cros_ec: wait for completion of commands that return IN_PROGRESS
i2c: i2c-cros-ec-tunnel: Set retries to 3
mfd: cros_ec: move locking into cros_ec_cmd_xfer
mfd: cros_ec: stop calling ->cmd_xfer() directly
mfd: cros_ec: Delay for 50ms when we see EC_CMD_REBOOT_EC
MAINTAINERS: Adds Andreas Werner to maintainers list for MEN F21BMC
mfd: arizona: Correct mask to allow setting micbias external cap
mfd: Add ACPI support
Revert "mfd: wm5102: Manually apply register patch"
mfd: ti_am335x_tscadc: Update logic in CTRL register for 5-wire TS
mfd: dt-bindings: atmel-gpbr: Rename doc file to conform to naming convention
mfd: dt-bindings: qcom-pm8xxx: Rename doc file to conform to naming convention
mfd: Inherit coherent_dma_mask from parent device
mfd: Document DT bindings for Qualcomm SPMI PMICs
mfd: Add support for Qualcomm SPMI PMICs
mfd: dt-bindings: pm8xxx: Add new compatible string
mfd: axp209x: Drop the parent supplies field
mfd: twl4030-power: Use 'ti,system-power-controller' as alternative way to support system power off
mfd: dt-bindings: twl4030-power: Use the standard property to mark power control
mfd: syscon: Add Atmel GPBR DT bindings documention
...
- Rework the handling of wakeup IRQs by the IRQ core such that
all of them will be switched over to "wakeup" mode in
suspend_device_irqs() and in that mode the first interrupt
will abort system suspend in progress or wake up the system
if already in suspend-to-idle (or equivalent) without executing
any interrupt handlers. Among other things that eliminates the
wakeup-related motivation to use the IRQF_NO_SUSPEND interrupt
flag with interrupts which don't really need it and should not
use it (Thomas Gleixner and Rafael J Wysocki).
- Switch over ACPI to handling wakeup interrupts with the help
of the new mechanism introduced by the above IRQ core rework
(Rafael J Wysocki).
- Rework the core generic PM domains code to eliminate code that's
not used, add DT support and add a generic mechanism by which
devices can be added to PM domains automatically during
enumeration (Ulf Hansson, Geert Uytterhoeven and Tomasz Figa).
- Add debugfs-based mechanics for debugging generic PM domains
(Maciej Matraszek).
- ACPICA update to upstream version 20140828. Included are updates
related to the SRAT and GTDT tables and the _PSx methods are in
the METHOD_NAME list now (Bob Moore and Hanjun Guo).
- Add _OSI("Darwin") support to the ACPI core (unfortunately, that
can't really be done in a straightforward way) to prevent
Thunderbolt from being turned off on Apple systems after boot
(or after resume from system suspend) and rework the ACPI Smart
Battery Subsystem (SBS) driver to work correctly with Apple
platforms (Matthew Garrett and Andreas Noever).
- ACPI LPSS (Low-Power Subsystem) driver update cleaning up the
code, adding support for 133MHz I2C source clock on Intel Baytrail
to it and making it avoid using UART RTS override with Auto Flow
Control (Heikki Krogerus).
- ACPI backlight updates removing the video_set_use_native_backlight
quirk which is not necessary any more, making the code check the
list of output devices returned by the _DOD method to avoid
creating acpi_video interfaces that won't work and adding a quirk
for Lenovo Ideapad Z570 (Hans de Goede, Aaron Lu and Stepan Bujnak).
- New Win8 ACPI OSI quirks for some Dell laptops (Edward Lin).
- Assorted ACPI code cleanups (Fabian Frederick, Rasmus Villemoes,
Sudip Mukherjee, Yijing Wang, and Zhang Rui).
- cpufreq core updates and cleanups (Viresh Kumar, Preeti U Murthy,
Rasmus Villemoes).
- cpufreq driver updates: cpufreq-cpu0/cpufreq-dt (driver name
change among other things), ppc-corenet, powernv (Viresh Kumar,
Preeti U Murthy, Shilpasri G Bhat, Lucas Stach).
- cpuidle support for DT-based idle states infrastructure, new
ARM64 cpuidle driver, cpuidle core cleanups (Lorenzo Pieralisi,
Rasmus Villemoes).
- ARM big.LITTLE cpuidle driver updates: support for DT-based
initialization and Exynos5800 compatible string (Lorenzo Pieralisi,
Kevin Hilman).
- Rework of the test_suspend kernel command line argument and
a new trace event for console resume (Srinivas Pandruvada,
Todd E Brandt).
- Second attempt to optimize swsusp_free() (hibernation core) to
make it avoid going through all PFNs which may be way too slow on
some systems (Joerg Roedel).
- devfreq updates (Paul Bolle, Punit Agrawal, Ãrjan Eide).
- rockchip-io Adaptive Voltage Scaling (AVS) driver and AVS
entry update in MAINTAINERS (Heiko Stübner, Kevin Hilman).
- PM core fix related to clock management (Geert Uytterhoeven).
- PM core's sysfs code cleanup (Johannes Berg).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=sIv/
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"Features-wise, to me the most important this time is a rework of
wakeup interrupts handling in the core that makes them work
consistently across all of the available sleep states, including
suspend-to-idle. Many thanks to Thomas Gleixner for his help with
this work.
Second is an update of the generic PM domains code that has been in
need of some care for quite a while. Unused code is being removed, DT
support is being added and domains are now going to be attached to
devices in bus type code in analogy with the ACPI PM domain. The
majority of work here was done by Ulf Hansson who also has been the
most active developer this time.
Apart from this we have a traditional ACPICA update, this time to
upstream version 20140828 and a few ACPI wakeup interrupts handling
patches on top of the general rework mentioned above. There also are
several cpufreq commits including renaming the cpufreq-cpu0 driver to
cpufreq-dt, as this is what implements generic DT-based cpufreq
support, and a new DT-based idle states infrastructure for cpuidle.
In addition to that, the ACPI LPSS driver is updated, ACPI support for
Apple machines is improved, a few bugs are fixed and a few cleanups
are made all over.
Finally, the Adaptive Voltage Scaling (AVS) subsystem now has a tree
maintained by Kevin Hilman that will be merged through the PM tree.
Numbers-wise, the generic PM domains update takes the lead this time
with 32 non-merge commits, second is cpufreq (15 commits) and the 3rd
place goes to the wakeup interrupts handling rework (13 commits).
Specifics:
- Rework the handling of wakeup IRQs by the IRQ core such that all of
them will be switched over to "wakeup" mode in suspend_device_irqs()
and in that mode the first interrupt will abort system suspend in
progress or wake up the system if already in suspend-to-idle (or
equivalent) without executing any interrupt handlers. Among other
things that eliminates the wakeup-related motivation to use the
IRQF_NO_SUSPEND interrupt flag with interrupts which don't really
need it and should not use it (Thomas Gleixner and Rafael Wysocki)
- Switch over ACPI to handling wakeup interrupts with the help of the
new mechanism introduced by the above IRQ core rework (Rafael Wysocki)
- Rework the core generic PM domains code to eliminate code that's
not used, add DT support and add a generic mechanism by which
devices can be added to PM domains automatically during enumeration
(Ulf Hansson, Geert Uytterhoeven and Tomasz Figa).
- Add debugfs-based mechanics for debugging generic PM domains
(Maciej Matraszek).
- ACPICA update to upstream version 20140828. Included are updates
related to the SRAT and GTDT tables and the _PSx methods are in the
METHOD_NAME list now (Bob Moore and Hanjun Guo).
- Add _OSI("Darwin") support to the ACPI core (unfortunately, that
can't really be done in a straightforward way) to prevent
Thunderbolt from being turned off on Apple systems after boot (or
after resume from system suspend) and rework the ACPI Smart Battery
Subsystem (SBS) driver to work correctly with Apple platforms
(Matthew Garrett and Andreas Noever).
- ACPI LPSS (Low-Power Subsystem) driver update cleaning up the code,
adding support for 133MHz I2C source clock on Intel Baytrail to it
and making it avoid using UART RTS override with Auto Flow Control
(Heikki Krogerus).
- ACPI backlight updates removing the video_set_use_native_backlight
quirk which is not necessary any more, making the code check the
list of output devices returned by the _DOD method to avoid
creating acpi_video interfaces that won't work and adding a quirk
for Lenovo Ideapad Z570 (Hans de Goede, Aaron Lu and Stepan Bujnak)
- New Win8 ACPI OSI quirks for some Dell laptops (Edward Lin)
- Assorted ACPI code cleanups (Fabian Frederick, Rasmus Villemoes,
Sudip Mukherjee, Yijing Wang, and Zhang Rui)
- cpufreq core updates and cleanups (Viresh Kumar, Preeti U Murthy,
Rasmus Villemoes)
- cpufreq driver updates: cpufreq-cpu0/cpufreq-dt (driver name change
among other things), ppc-corenet, powernv (Viresh Kumar, Preeti U
Murthy, Shilpasri G Bhat, Lucas Stach)
- cpuidle support for DT-based idle states infrastructure, new ARM64
cpuidle driver, cpuidle core cleanups (Lorenzo Pieralisi, Rasmus
Villemoes)
- ARM big.LITTLE cpuidle driver updates: support for DT-based
initialization and Exynos5800 compatible string (Lorenzo Pieralisi,
Kevin Hilman)
- Rework of the test_suspend kernel command line argument and a new
trace event for console resume (Srinivas Pandruvada, Todd E Brandt)
- Second attempt to optimize swsusp_free() (hibernation core) to make
it avoid going through all PFNs which may be way too slow on some
systems (Joerg Roedel)
- devfreq updates (Paul Bolle, Punit Agrawal, Ãrjan Eide).
- rockchip-io Adaptive Voltage Scaling (AVS) driver and AVS entry
update in MAINTAINERS (Heiko Stübner, Kevin Hilman)
- PM core fix related to clock management (Geert Uytterhoeven)
- PM core's sysfs code cleanup (Johannes Berg)"
* tag 'pm+acpi-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (105 commits)
ACPI / fan: printk replacement
PM / clk: Fix crash in clocks management code if !CONFIG_PM_RUNTIME
PM / Domains: Rename cpu_data to cpuidle_data
cpufreq: cpufreq-dt: fix potential double put of cpu OF node
cpufreq: cpu0: rename driver and internals to 'cpufreq_dt'
PM / hibernate: Iterate over set bits instead of PFNs in swsusp_free()
cpufreq: ppc-corenet: remove duplicate update of cpu_data
ACPI / sleep: Rework the handling of ACPI GPE wakeup from suspend-to-idle
PM / sleep: Rename platform suspend/resume functions in suspend.c
PM / sleep: Export dpm_suspend_late/noirq() and dpm_resume_early/noirq()
ACPICA: Introduce acpi_enable_all_wakeup_gpes()
ACPICA: Clear all non-wakeup GPEs in acpi_hw_enable_wakeup_gpe_block()
ACPI / video: check _DOD list when creating backlight devices
PM / Domains: Move dev_pm_domain_attach|detach() to pm_domain.h
cpufreq: Replace strnicmp with strncasecmp
cpufreq: powernv: Set the cpus to nominal frequency during reboot/kexec
cpufreq: powernv: Set the pstate of the last hotplugged out cpu in policy->cpus to minimum
cpufreq: Allow stop CPU callback to be used by all cpufreq drivers
PM / devfreq: exynos: Enable building exynos PPMU as module
PM / devfreq: Export helper functions for drivers
...
Since the i2c bus can get wedged on the EC sometimes, set the number of retries
to 3. Since we un-wedge the bus immediately after the wedge happens, this is the
correct fix since only one transfer will fail.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Instead of having users of the ChromeOS EC call the interface-specific
cmd_xfer() callback directly, introduce a central cros_ec_cmd_xfer()
to use instead. This will allow us to put all the locking and retry
logic in one place instead of duplicating it across the different
drivers.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In the case of errors during probe, we should disable i2c_imx->clk.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for AMD version of the DW I2C host controller. The device is
enumerated from ACPI namespace with ACPI ID AMD0010. Because the core
driver needs an input source clock, and this is not an Intel LPSS device
where clocks are provided through drivers/acpi/acpi_lpss.c, we register the
clock ourselves if the clock rate is given in ->driver_data
Signed-off-by: Carl Peng <carlpeng008@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In order to be able to create missing clock for AMD (and in future possibly
others) we move getting clock for the device a bit later. Also make ACPI/DT
configuration in the same place depending on from where the device was
enumerated from.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is no way in ACPI to tell in which speed the host controller is
supposed to run, so we default to fast mode (400KHz). Since this has been
the default all the time there should be no functional changes with this
change.
This is the first step required to refactor the driver probe so that we can
supply source clock from ACPI part of the driver to the core.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add I2C bus driver for the controller found in the LSI Axxia family SoCs. The
driver implements 10-bit addressing and SMBus transfer modes via emulation
(including SMBus block data read).
Signed-off-by: Anders Berg <anders.berg@avagotech.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The HSI2C module on Exynos7 differs in the transfer status
bits. Transfer status bits were moved to INT_ENABLE and
INT_STATUS registers
This patch adds support for the HSI2C module on Exynos7.
1. Implementes a "hw" field in the variant struct to distinguish
the hardware.
2. Updates the dt-new compatible in dt-binding documenation
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2cdetect scanned i2c bus slow because the i2c-mxs driver ignored the
NO_SLAVE_ACK bit during busy-waiting loop. Thanks to the patch, the
speedup happens.
Signed-off-by: Janusz Uzycki <j.uzycki@elproma.com.pl>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The runtime pm calls need to be done before populating the children via the
i2c_add_adapter call. If this is not done, a child can run into issues trying
to do i2c read/writes due to the pm_runtime_sync failing.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
i2cdetect -q was broken (everything was a false positive, and no transfers were
actually being sent over i2c). The way it works is by sending a 0 length write
request and checking for NACK. This patch fixes the 0 length writes and actually
sends them.
Reported-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Tested-by: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
In <https://lkml.org/lkml/2014/6/10/265> pointed out that the 10-bit
flag in the cros_ec_tunnel was useless. It went into a 16-bit flags
field but was defined at (1 << 16).
Since we have no 10-bit i2c devices on the other side of the tunnel on
any known devices this was never a problem. Until we do it makes
sense to remove this code. On the EC side the code to handle this
flag was removed in <https://chromium-review.googlesource.com/204162>.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The commit 46420dd73b (PM / Domains: Add APIs to attach/detach a PM
domain for a device) started using errno values in pm.h header file.
It also failed to include the header for these, thus it caused
compiler errors.
Instead of including the errno header to pm.h, let's move the functions
to pm_domain.h, since it's a better match.
Fixes: 46420dd73b (PM / Domains: Add APIs to attach/detach a PM domain for a device)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To enable the cros-ec-tunnel driver to be auto-loaded when build as a
module add an of match table (and export it) to match the modalias
information passed on to userspace as the Cros EC MFD driver registers
the MFD subdevices with an of_compatibility string.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
gcc rightfully says:
drivers/i2c/busses/i2c-rcar.c:198:10: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Software is allowed to allocate number of descriptor size from 2 to 256,
this i2c controller could process more descriptor, but for i2c core soft
ware layer, only one i2c transaction is allowed each time.
So here switch to minimum 2 descriptor when initialization.
Signed-off-by: Fan Du <fan.du@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
According to the i.mx spec, for multimaster mode, if I2C is
enabled when the bus is busy and asserts start, hardware inhibits
the transmission, clears MSTA without signaling a stop, generate
an interrupt, and set I2C_I2SR[IAL] to indicate a failed attempt
to engage the bus, which means arbitration lost. In this case,
we should first test I2C_I2SR[IAL], and clear this bit if it is
set, and then I2C controller default to slave receive mode.
This patch check the IAL bit every time before an I2c transmission.
if IAL is set, clear it and make I2C controller to default mode.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Having a transfer more than 32 bits is not all that unlikely. Remove
the annotation.
The unlikely in the IRQ handler can't gain us much. It's not in a
loop, so at most it would save 1 instruction per IRQ, which isn't
much. In fact on the compiler I tested it produced the exact same
code. Remove it too.
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Check if the ICMSR register (masked with the ICMIER register) evaluates to 0 in
the driver's interrupt handler and return IRQ_NONE in that case, like many other
drivers do.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
rcar_i2c_prepare_msg() always returns 0, so we can make this function return
*void* and thus remove the result check in rcar_i2c_master_xfer().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
rcar_i2c_master_xfer() needlessly compares the message pointers (using indirect
addressing) in order to detect the last I2C message, while it's enough to only
compare the message indexes.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use the platform data to set the clk_freq when there is no DT configuration
available. The clk_freq in turn will determine the I2C speed mode.
In Quark, there is currently no other configuration mechanism other than
board files.
Signed-off-by: Raymond Tan <raymond.tan@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Hock Leong Kweh <hock.leong.kweh@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some legacy devices support ony I2C standard mode at 100kHz.
This patch allows to select the standard mode through the DTS
with the use of the existing clock-frequency parameter.
When clock-frequency parameter is not set, the fast mode is selected.
Only when the parameter is set at 100000, the standard mode is selected.
Signed-off-by: Romain Baeriswyl <romainba@abilis.com>
Reviewed-by: Christian Ruppert <christian.ruppert@abilis.com>
Acked-by: Alan Tull <atull@opensource.altera.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch fix spelling typos found in Kconfig.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If adapter->dev.parent == NULL there is a NULL pointer dereference in
acpi_i2c_install_space_handler and acpi_i2c_remove_space_handler.
This is present since introduction of this code:
366047515c "i2c: rework kernel config I2C_ACPI" or even
da3c6647ee "I2C/ACPI: Clean up I2C ACPI code and Add CONFIG_I2C_ACPI"
The adapter->dev.parent == NULL case is valid for the i2c_stub,
so loading i2c_stub with ACPI_I2C_OPREGION enabled results in an oops.
This is also valid at least for i2c_tiny_usb and i2c_robotfuzz_osif.
Fix by checking whether it is null before calling ACPI_HANDLE.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 5d98e61d33 ("I2C/ACPI: Add i2c ACPI operation region support")
renamed the i2c-core module. This may cause regressions for
distributions, so put the ACPI code back into the core.
Reported-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Lan Tianyu <tianyu.lan@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Previously only the ACPI PM domain was supported by the i2c bus.
Let's convert to the common attach/detach functions for PM domains,
which currently means we are extending the support to include the
generic PM domain as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
I2C_CLKDIV register descripted in the previous version of
RK3x chip manual is incorrect. Plus 1 is required.
The correct formula:
- T(SCL_HIGH) = T(PCLK) * (CLKDIVH + 1) * 8
- T(SCL_LOW) = T(PCLK) * (CLKDIVL + 1) * 8
- (SCL Divsor) = 8 * ((CLKDIVL + 1) + (CLKDIVH + 1))
- SCL = PCLK / (CLK Divsor)
It will be updated to the latest version of chip manual.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
If I2C_M_RD flag is set SELECT command is sent and afterward READ
command. The patch fixes READ command to return READ failure error
message instead of SELECT failure error message.
Signed-off-by: Janusz Uzycki <j.uzycki@elproma.com.pl>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In block write mode, when encapsulating dma_buffer, first element is
'command', the rest is data buffer, so only copy actual data buffer
starting from block[1] with the size indicating by block[0].
Signed-off-by: Fan Du <fan.du@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Bits 8-31 of all registers reflect the value of bits 0-7 on reads and should be
0 on writes, according to the manuals. RCAR_IRQ_ACK_{RECV|SEND} macros have all
1's in bits 8-31, thus going against the manuals, so fix them.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently the i2c-tegra bus driver prepares, enables
and set_rates its clocks separately for each transfer.
This causes locking problems when doing I2C transfers
from clock notifiers; see
http://lists.infradead.org/pipermail/linux-arm-kernel/2014-July/268653.html
This patch moves clk_prepare/unprepare and clk_set_rate calls to
the probe function, leaving only clk_enable/disable to be
done on each transfer. This solves the locking issue.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This reverts commit 150b8be3cd.
The I2C core's per-adapter locks can't protect from IRQs, so the driver still
needs a spinlock to protect the register accesses.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: stable@vger.kernel.org # 3.16+
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver was not bound checking the received length byte to ensure it was within the
the buffer size that is allocated for SMBus blocks. This resulted in buffer overflows
whenever an invalid length byte was received.
It also failed to ensure the length byte was not zero. If it received zero, it would end up
in an infinite loop as the at91_twi_read_next_byte function returned immediately without
allowing RHR to be read to clear the RXRDY interrupt.
Tested agaisnt a SMBus compliant battery.
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
In rk3x SOC, the I2C controller can receive/transmit up to 32 bytes data
in one chunk, so the size of data to be write/read to/from TXDATAx/RXDATAx
must be less than or equal 32 bytes at a time.
Tested on rk3288-pinky board, elan receive 158 bytes data.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Acked-by: Max Schwarz <max.schwarz@online.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
There is a race condition in at91_do_twi_xfer when signals arrive.
If a signal is recieved while waiting for a transfer to complete
wait_for_completion_interruptible_timeout() will return -ERESTARTSYS.
This is not handled correctly resulting in interrupts still being
enabled and a transfer being in flight when we return.
Symptoms include a range of oopses and bus lockups. Oopses can happen
when the transfer completes because the interrupt handler will corrupt
the stack. If a new transfer is started before the interrupt fires
the controller will start a new transfer in the middle of the old one,
resulting in confused slaves and a locked bus.
To avoid this, use wait_for_completion_io_timeout instead so that we
don't have to deal with gracefully shutting down the transfer and
disabling the interrupts.
Signed-off-by: Simon Lindgren <simon@aqwary.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
The "clock-frequency" DT property is listed as optional, However,
the current code stores the return value of of_property_read_u32 in
the return code of mv64xxx_of_config, but then forgets to clear it
after setting the default value of "clock-frequency". It is then
passed out to the main probe function, resulting in a probe failure
when "clock-frequency" is missing.
This patch checks and then throws away the return value of
of_property_read_u32, instead of storing it and having to clear it
afterwards.
This issue was discovered after the property was removed from all
sunxi DTs.
Fixes: 4c730a06c1 ("i2c: mv64xxx: Set bus frequency to 100kHz if clock-frequency is not provided")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Cc: stable@vger.kernel.org
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Sometimes the MNR and MST interrupts happen simultaneously (stop automatically
follows NACK, according to the manuals) and in such case the ID_NACK flag isn't
set since the MST interrupt handling precedes MNR and all interrupts are cleared
and disabled then, so that MNR interrupt is never noticed -- this causes NACK'ed
transfers to be falsely reported as successful. Exchanging MNR and MST handlers
fixes this issue, however the MNR bit somehow gets set again even after being
explicitly cleared, so I decided to completely suppress handling of all disabled
interrupts (which is a good thing anyway)...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch fix spelling typo in printk within vairous
part of the code.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The SMBus host controller is the same as used in Baytrail so add the new
PCI ID to the driver's list of supported IDs.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit da3c6647(I2C/ACPI: Clean up I2C ACPI code and Add CONFIG_I2C_ACPI
config) adds a new kernel config I2C_ACPI and make I2C core built in
when the config is selected. This is wrong because distributions
etc generally compile I2C as a module and the commit broken that.
This patch is to rename I2C_ACPI to ACPI_I2C_OPREGION. New config
only controls ACPI I2C operation region code and depends on I2C=y.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[wsa: removed unrelated change for Kconfig]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"Highlights:
- class based instantiation finally dropped for most embedded drivers
bringing boot up performance gains
- removed two drivers (one outdated, one a duplicate)
- ACPI has now operation region support (thanks to Lan Tianyu)
- the i2c-stub driver got overhauled and gained new features to
become more useful when writing i2c client drivers (thanks to
Guenter Roeck and Jean Delvare)
The rest is driver bugfixes, added bindings/ids, cleanups..."
* 'i2c/for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (43 commits)
i2c: mpc: delete unneeded test before of_node_put
i2c: rk3x: fix interrupt handling issue
i2c: imx: Fix format warning for dev_dbg
i2c: qup: disable clks and return instead of just returning error
i2c: exynos5: always enable HSI2C
i2c: designware: add new bindings
i2c: gpio: Drop dead code in i2c_gpio_remove
i2c: pca954x: put the mux to disconnected state after resume
i2c: st: Update i2c timings
drivers/i2c/busses: use correct type for dma_map/unmap
i2c: i2c-st: Use %pa to print 'resource_size_t' type
i2c: s3c2410: resume the I2C controller earlier
i2c: stub: Avoid an array overrun on I2C block transfers
i2c: i801: Add device ID for Intel Wildcat Point PCH
i2c: i801: Fix the alignment of the device table
i2c: stub: Add support for banked register ranges
i2c: stub: Remember the number of emulated chips
i2c: stub: Add support for SMBus block commands
i2c: efm32: correct namespacing of location property
i2c: exynos5: remove extra line and fix an assignment
...
Of_node_put supports NULL as its argument, so the initial test is not
necessary.
Suggested by Uwe Kleine-König.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
@@
-if (e)
of_node_put(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If slave holds scl, I2C_IPD[7] will be set 1 by controller
for debugging. Driver must ignore it.
[ 5.752391] rk3x-i2c ff160000.i2c: unexpected irq in WRITE: 0x80
[ 5.939027] rk3x-i2c ff160000.i2c: timeout, ipd: 0x80, state: 4
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
- Checkpatch fixes throughout the subsystem
- Use Regmap to handle IRQs in max77686, extcon-max77693 and mc13xxx-core
- Use DMA in rtsx_pcr
- Restrict building on unsupported architectures on timberdale, cs5535
- SPI hardening in cros_ec_spi
- More robust error handing in asic3, cros_ec, ab8500-debugfs,
max77686 and pcf50633-core
- Reorder PM runtime and regulator handing during shutdown in arizona
- Enable wakeup in cros_ec_spi
- Unused variable/code clean-up in pm8921-core, cros_ec, htc-i2cpld,
tps65912-spi, wm5110-tables and ab8500-debugfs
- Add regulator handing into suspend() in sec-core
- Remove pointless wrapper functions in extcon-max77693 and i2c-cros-ec-tunnel
- Use cross-architecture friendly data sizes in stmpe-i2c, arizona,
max77686 and tps65910
- Device Tree documentation updates throughout
- Provide power management support in max77686
- Few OF clean-ups in max77686
- Use manged resources in tps6105x
== New drivers/supported devices ==
- Add support for s2mpu02 to sec-core
- Add support for Allwinner A32 to sun6i-prcm
- Add support for Maxim 77802 in max77686
- Add support for DA9063 AD in da9063
- Add new driver for Intel PMICs (generic) and specifically Crystal Cove
== (Re-)moved drivers ==
- Move out keyboard functionality cros_ec ==> input/keyboard/cros_ec_keyb
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2cNI
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD update from Lee Jones:
"Changes to existing drivers:
- checkpatch fixes throughout the subsystem
- use Regmap to handle IRQs in max77686, extcon-max77693 and
mc13xxx-core
- use DMA in rtsx_pcr
- restrict building on unsupported architectures on timberdale,
cs5535
- SPI hardening in cros_ec_spi
- more robust error handing in asic3, cros_ec, ab8500-debugfs,
max77686 and pcf50633-core
- reorder PM runtime and regulator handing during shutdown in arizona
- enable wakeup in cros_ec_spi
- unused variable/code clean-up in pm8921-core, cros_ec, htc-i2cpld,
tps65912-spi, wm5110-tables and ab8500-debugfs
- add regulator handing into suspend() in sec-core
- remove pointless wrapper functions in extcon-max77693 and
i2c-cros-ec-tunnel
- use cross-architecture friendly data sizes in stmpe-i2c, arizona,
max77686 and tps65910
- devicetree documentation updates throughout
- provide power management support in max77686
- few OF clean-ups in max77686
- use manged resources in tps6105x
New drivers/supported devices:
- add support for s2mpu02 to sec-core
- add support for Allwinner A32 to sun6i-prcm
- add support for Maxim 77802 in max77686
- add support for DA9063 AD in da9063
- new driver for Intel PMICs (generic) and specifically Crystal Cove
(Re-)moved drivers ==
- move out keyboard functionality cros_ec ==> input/keyboard/cros_ec_keyb"
* tag 'mfd-for-linus-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (101 commits)
MAINTAINERS: Update MFD repo location
mfd: omap-usb-host: Fix improper mask use.
mfd: arizona: Only free the CTRLIF_ERR IRQ if we requested it
mfd: arizona: Add missing handling for ISRC3 under/overclocked
mfd: wm5110: Add new interrupt register definitions
mfd: arizona: Rename thermal shutdown interrupt
mfd: wm5110: Add in the output done interrupts
mfd: wm5110: Remove non-existant interrupts
mfd: tps65912-spi: Remove unused variable
mfd: htc-i2cpld: Remove unused code
mfd: da9063: Add support for AD silicon variant
mfd: arizona: Map MICVDD from extcon device to the Arizona core
mfd: arizona: Add MICVDD to mapped regulators for wm8997
mfd: max77686: Ensure device type IDs are architecture agnostic
mfd: max77686: Add Maxim 77802 PMIC support
mfd: tps6105x: Use managed resources when allocating memory
mfd: wm8997-tables: Suppress 'line over 80 chars' warnings
mfd: kempld-core: Correct a variety of checkpatch warnings
mfd: ipaq-micro: Fix coding style errors/warnings reported by checkpatch
mfd: si476x-cmd: Remedy checkpatch style complains
...
Fixes the following by using %pR:
drivers/i2c/busses/i2c-imx.c: In function i2c_imx_probe()
drivers/i2c/busses/i2c-imx.c:689:2: warning: format 0x%x expects argument
of type unsigned int, but argument 4 has type resource_size_t [-Wformat=]
dev_dbg(&i2c_imx->adapter.dev, "device resources from 0x%x to 0x%x\n",
^
...
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This fixes a error handling scenario where clocks were not being disabled
when QUP_OUTPUT_BLOCK_SIZE returns a size greater than the size of blk_sizes
array. So this patch adds a statement to jump to the fail lable to release the
clocks.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Acked-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
All Exynos5 platforms have HSI2C controllers and are needed by
various IPs connected to the boards based on these SoCs. Thus
select this by default for Exynos5 platforms.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
drivers and fixes/enhancements to existing clock drivers. There are also
some non-critical fixes and improvements to the framework core.
Changes to the clock framework core include:
* improvements to printks on errors
* flattening the previously hierarchal structure of per-clock entries
in debugfs
* allow per-clock debugfs entries that are specific to a particular
clock driver
* configure initial clock parent and/or initial clock rate from Device
Tree
* several feature enhancements to the composite clock type
* misc fixes
New clock drivers added include:
* TI Palmas PMIC
* Allwinner A23 SoC
* Qualcomm APQ8084 and IPQ8064 SoCs
* Rockchip rk3188, rk3066 and rk3288 SoCs
* STMicroelectronics STiH407 SoC
* Cirrus Logic CLPS711X SoC
Many fixes, feature enhancements and further clock tree support for
existing clock drivers also were merged, such as Samsung's "ARMCLK down"
power saving feature for their Exynos4 & Exynos5 SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=48y9
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.17' of git://git.linaro.org/people/mike.turquette/linux
Pull clock framework updates from Mike Turquette:
"The clock framework changes for 3.17 are mostly additions of new clock
drivers and fixes/enhancements to existing clock drivers. There are
also some non-critical fixes and improvements to the framework core.
Changes to the clock framework core include:
- improvements to printks on errors
- flattening the previously hierarchal structure of per-clock entries
in debugfs
- allow per-clock debugfs entries that are specific to a particular
clock driver
- configure initial clock parent and/or initial clock rate from
Device Tree
- several feature enhancements to the composite clock type
- misc fixes
New clock drivers added include:
- TI Palmas PMIC
- Allwinner A23 SoC
- Qualcomm APQ8084 and IPQ8064 SoCs
- Rockchip rk3188, rk3066 and rk3288 SoCs
- STMicroelectronics STiH407 SoC
- Cirrus Logic CLPS711X SoC
Many fixes, feature enhancements and further clock tree support for
existing clock drivers also were merged, such as Samsung's "ARMCLK
down" power saving feature for their Exynos4 & Exynos5 SoCs"
* tag 'clk-for-linus-3.17' of git://git.linaro.org/people/mike.turquette/linux: (86 commits)
clk: Add missing of_clk_set_defaults export
clk: checking wrong variable in __set_clk_parents()
clk: Propagate any error return from debug_init()
clk: clps711x: Add DT bindings documentation
clk: Add CLPS711X clk driver
clk: st: Use round to closest divider flag
clk: st: Update frequency tables for fs660c32 and fs432c65
clk: st: STiH407: Support for clockgenA9
clk: st: STiH407: Support for clockgenD0/D2/D3
clk: st: STiH407: Support for clockgenC0
clk: st: Add quadfs reset handling
clk: st: Add polarity bit indication
clk: st: STiH407: Support for clockgenA0
clk: st: STiH407: Support for A9 MUX Clocks
clk: st: STiH407: Support for Flexgen Clocks
clk: st: Adds Flexgen clock binding
clk: st: Remove uncessary (void *) cast
clk: st: use static const for clkgen_pll_data tables
clk: st: use static const for stm_fs tables
clk: st: Update ST clock binding documentation
...
This may appear as PCI or ACPI depending upon the firmware so we
have to list both. All share the same ACPI identifier but not
the same PCI identifier.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit a0682a31 ("i2c: gpio: Use devm_gpio_request()") left unused
code behind, clean it up.
Fixes: a0682a3158 ("i2c: gpio: Use devm_gpio_request()")
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
pca954x may be power lost during suspend, so after resume we also suffer
the issue fixed by commit cd823db8b1,
"pca954x power-on default is channel 0 connected. If multiple pca954x
muxes are connected to the same physical I2C bus, the parent bus will
see channel 0 devices behind both muxes by default."
What's more, when resume bootloader may also operate the mux, so the
the channel connected after that may not be the one driver thought.
We fix this problem by putting the mux to disconnected state and
clearing last_chan in the resume hook.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c timing values specified in the driver are the minimun values
defined in the I2C specifications. The I2C specification does not
specify any default or maximum values.
Some I2C devices are out of spec, such as the HDMI link of the Toshiba
19AV600 TV, and might not work properly with minimum values.
This patch adds a 10% margin on all the timings in both Normal and Fast modes.
Trial and error method have been used to find the minimum margin necessary to
have the out-of-spec device working, and a security margin has been added.
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When building multi_v7_defconfig with CONFIG_ARM_LPAE=y the following warning
is seen:
drivers/i2c/busses/i2c-st.c:818:2: warning: format '%x' expects argument of type
'unsigned int', but argument 4 has type 'resource_size_t' [-Wformat=]
Use %pa to print 'resource_size_t' type to fix the warning.
Reported-by: Olof's autobuilder <build@lixom.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When the wake-up is triggered by the PMIC RTC, the RTC driver is trying
to read the PMIC interrupt status over I2C and fails because the I2C
controller is not resumed yet.
Let's resume the I2C controller earlier in the _noirq phase
(as other hardwares are doing), so we can properly get the wake-up
condition.
[tomasz: Also fixes certain issues on Exynos4-based boards.]
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds helper functions to configure clock parents and rates
as specified through 'assigned-clock-parents', 'assigned-clock-rates'
DT properties for a clock provider or clock consumer device.
The helpers are now being called by the bus code for the platform, I2C
and SPI busses, before the driver probing and also in the clock core
after registration of a clock provider.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
I2C block transfers can have a size up to 32 bytes. If starting close
to the end of the address space, there may not be enough room to write
that many bytes (on I2C block writes) or not enough bytes to be read
(on I2C block reads.) In that case, we must shorten the transfer so
that it does not exceed the address space.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
A long name broke the alignment, shift the columns a bit to fix it and
make the table look nice again. While we're here, switch to the
standard comment style to make checkpatch happy, and use tabs instead
of spaces for column alignment.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some chips implement banked register ranges. This allows implementing
more registers than the limited 8-bit address space originally allows.
In order to access a register on these chips, you must first select
the proper bank. Add support for this mechanism to the i2c-stub driver
so that such chips can be emulated. All the bank settings are passed
as module parameters.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This makes initialization, cleanup and look-up easier.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
SMBus block commands are different to I2C block commands since
the returned data is not normally accessible with byte or word
commands on other command offsets. Add linked list of 'block'
commands to support those commands.
Access mechanism is quite simple: Block commands must be written
before they can be read. Subsequent writes can be partial. Block
read commands always return the number of bytes associated with
the longest previous write.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Olof Johansson pointed out that usually the company name is picked as
namespace prefix to specific properties. So expect "energymicro,location"
but fall back to the previously introduced name "efm32,location".
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch does the following in exynos5_i2c_message_start() function
1. Fixes an assignment
As, "i2c_auto_conf" is initialized to '0' at the beginning of the
function and HSI2C_READ_WRITE is defined as (1u << 16)
Using "|=" for the first assignment is more readable.
2. Removes an extra line
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch removes an extra read of FIFO_STATUS register in the interrrupt
service routine. Which is read again before the actual use.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The original code for the exynos i2c controller registered for the
"noirq" variants. However during review feedback it was moved to
SIMPLE_DEV_PM_OPS without anyone noticing that it meant we were no
longer actually "noirq" (despite functions named
exynos5_i2c_suspend_noirq and exynos5_i2c_resume_noirq).
i2c controllers that might have wakeup sources on them seem to need to
resume at noirq time so that the individual drivers can actually read
the i2c bus to handle their wakeup.
NOTE: I took the original review feedback from Wolfram and added
poweroff, thaw, freeze, restore.
This patch has only been compile-tested since I don't have all the
patches needed to make my machine using this i2c driver actually
suspend/resume.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver has been flagged to drop class based instantiation. The removal
improves boot-up time and is unneeded for embedded controllers. Users have been
warned to switch for some time now, so we can actually do the removal. Keep the
DEPRECATED flag, so the core can inform users that the behaviour finally
changed now. After another transition period, this flag can go, too.
While we are here, remove the indentation for the array setup because
such things always break after some time.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver has been flagged to drop class based instantiation. The removal
improves boot-up time and is unneeded for embedded controllers. Users have been
warned to switch for some time now, so we can actually do the removal. Keep the
DEPRECATED flag, so the core can inform users that the behaviour finally
changed now. After another transition period, this flag can go, too.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
This driver has been flagged to drop class based instantiation. The removal
improves boot-up time and is unneeded for embedded controllers. Users have been
warned to switch for some time now, so we can actually do the removal. Keep the
DEPRECATED flag, so the core can inform users that the behaviour finally
changed now. After another transition period, this flag can go, too.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This driver has been flagged to drop class based instantiation. The removal
improves boot-up time and is unneeded for embedded controllers. Users have been
warned to switch for some time now, so we can actually do the removal. Keep the
DEPRECATED flag, so the core can inform users that the behaviour finally
changed now. After another transition period, this flag can go, too.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver has been flagged to drop class based instantiation. The removal
improves boot-up time and is unneeded for embedded controllers. Users have been
warned to switch for some time now, so we can actually do the removal. Keep the
DEPRECATED flag, so the core can inform users that the behaviour finally
changed now. After another transition period, this flag can go, too.
While we are here, remove the indentation for the array setup because
such things always break after some time.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Sachin Kamat <sachin.kamat@samsung.com>
This driver has been flagged to drop class based instantiation. The removal
improves boot-up time and is unneeded for embedded controllers. Users have been
warned to switch for some time now, so we can actually do the removal. Keep the
DEPRECATED flag, so the core can inform users that the behaviour finally
changed now. After another transition period, this flag can go, too.
While we are here, remove the indentation for the array setup because
such things always break after some time.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver has been flagged to drop class based instantiation. The removal
improves boot-up time and is unneeded for embedded controllers. Users have been
warned to switch for some time now, so we can actually do the removal. Keep the
DEPRECATED flag, so the core can inform users that the behaviour finally
changed now. After another transition period, this flag can go, too.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver has been flagged to drop class based instantiation. The removal
improves boot-up time and is unneeded for embedded controllers. Users have been
warned to switch for some time now, so we can actually do the removal. Keep the
DEPRECATED flag, so the core can inform users that the behaviour finally
changed now. After another transition period, this flag can go, too.
While we are here, remove the indentation for the array setup because
such things always break after some time.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
This driver has been flagged to drop class based instantiation. The removal
improves boot-up time and is unneeded for embedded controllers. Users have been
warned to switch for some time now, so we can actually do the removal. Keep the
DEPRECATED flag, so the core can inform users that the behaviour finally
changed now. After another transition period, this flag can go, too.
While we are here, remove the indentation for the array setup because
such things always break after some time.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This driver has been flagged to drop class based instantiation. The removal
improves boot-up time and is unneeded for embedded controllers. Users have been
warned to switch for some time now, so we can actually do the removal. Keep the
DEPRECATED flag, so the core can inform users that the behaviour finally
changed now. After another transition period, this flag can go, too.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver has been flagged to drop class based instantiation. The removal
improves boot-up time and is unneeded for embedded controllers. Users have been
warned to switch for some time now, so we can actually do the removal. Keep the
DEPRECATED flag, so the core can inform users that the behaviour finally
changed now. After another transition period, this flag can go, too.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver has been flagged to drop class based instantiation. The removal
improves boot-up time and is unneeded for embedded controllers. Users have been
warned to switch for some time now, so we can actually do the removal. Keep the
DEPRECATED flag, so the core can inform users that the behaviour finally
changed now. After another transition period, this flag can go, too.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver has been flagged to drop class based instantiation. The removal
improves boot-up time and is unneeded for embedded controllers. Users have been
warned to switch for some time now, so we can actually do the removal. Keep the
DEPRECATED flag, so the core can inform users that the behaviour finally
changed now. After another transition period, this flag can go, too.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver has been flagged to drop class based instantiation. The removal
improves boot-up time and is unneeded for embedded controllers. Users have been
warned to switch for some time now, so we can actually do the removal. Keep the
DEPRECATED flag, so the core can inform users that the behaviour finally
changed now. After another transition period, this flag can go, too.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver has been flagged to drop class based instantiation. The removal
improves boot-up time and is unneeded for embedded controllers. Users have been
warned to switch for some time now, so we can actually do the removal. Keep the
DEPRECATED flag, so the core can inform users that the behaviour finally
changed now. After another transition period, this flag can go, too.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We have a warning already when support for old-fashioned class based
instantiation is about to be dropped somewhen soon from a driver. Let's
have another one when it was actually dropped. This allows to remove the
cruft a little earlier and still let users know what happened in the
rare case they are missing devices after the change. However, there is
enough interest to get rid of class based instantiation rather sooner
than later because it improves boot up time.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver is marked as deprecated since the pre-git era. Any user
left(?) should really have switched to i2c-gpio meanwhile.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Jim Cromie <jim.cromie@gmail.com>
It turned out that the s6000 simply has a designware IP core and should
use the designated driver for it which is way more maintained and
feature complete. There are currently no users in tree, and not even a
toolchain for s6000 seems to be available. So, simply remove this
duplicate. If someone needs assistance in converting to the designware
driver, the i2c list will be there to help.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When communicating with the EC, the cmd_xfer() function should return the
number of bytes it received from the EC, or negative on error.
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove the three wrapper functions that talk to the EC without passing all
the desired arguments and just use the underlying communication function
that passes everything in a struct intead.
This is internal code refactoring only. Nothing should change.
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Get rid of some boilerplate code by using module_serio_driver().
Signed-off-by: Christoph Jaeger <christophjaeger@linux.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Clean up ACPI related code in the i2c core and add CONFIG_I2C_ACPI
to enable I2C ACPI code.
Current there is a race between removing I2C ACPI operation region
and ACPI AML code accessing. So make i2c core built-in if CONFIG_I2C_ACPI
is set.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
ACPI 5.0 spec(5.5.2.4.5) defines GenericSerialBus(i2c, spi, uart) operation region.
It allows ACPI aml code able to access such kind of devices to implement
some ACPI standard method.
ACPI Spec defines some access attribute to associate with i2c protocol.
AttribQuick Read/Write Quick Protocol
AttribSendReceive Send/Receive Byte Protocol
AttribByte Read/Write Byte Protocol
AttribWord Read/Write Word Protocol
AttribBlock Read/Write Block Protocol
AttribBytes Read/Write N-Bytes Protocol
AttribProcessCall Process Call Protocol
AttribBlockProcessCall Write Block-Read Block Process Call Protocol
AttribRawBytes Raw Read/Write N-BytesProtocol
AttribRawProcessBytes Raw Process Call Protocol
On the Asus T100TA, Bios use GenericSerialBus operation region to access
i2c device to get battery info.
Sample code From Asus T100TA
Scope (_SB.I2C1)
{
Name (UMPC, ResourceTemplate ()
{
I2cSerialBus (0x0066, ControllerInitiated, 0x00061A80,
AddressingMode7Bit, "\\_SB.I2C1",
0x00, ResourceConsumer, ,
)
})
...
OperationRegion (DVUM, GenericSerialBus, Zero, 0x0100)
Field (DVUM, BufferAcc, NoLock, Preserve)
{
Connection (UMPC),
Offset (0x81),
AccessAs (BufferAcc, AttribBytes (0x3E)),
FGC0, 8
}
...
}
Device (BATC)
{
Name (_HID, EisaId ("PNP0C0A")) // _HID: Hardware ID
Name (_UID, One) // _UID: Unique ID
...
Method (_BST, 0, NotSerialized) // _BST: Battery Status
{
If (LEqual (AVBL, One))
{
Store (FGC0, BFFG)
If (LNotEqual (STAT, One))
{
ShiftRight (CHST, 0x04, Local0)
And (Local0, 0x03, Local0)
If (LOr (LEqual (Local0, One), LEqual (Local0, 0x02)))
{
Store (0x02, Local1)
}
...
}
The i2c operation region is defined under I2C1 scope. _BST method under
battery device BATC read battery status from the field "FCG0". The request
would be sent to i2c operation region handler.
This patch is to add i2c ACPI operation region support. Due to there are
only "Byte" and "Bytes" protocol access on the Asus T100TA, other protocols
have not been tested.
About RawBytes and RawProcessBytes protocol, they needs specific drivers to interpret
reference data from AML code according ACPI 5.0 SPEC(5.5.2.4.5.3.9 and 5.5.2.4.5.3.10).
So far, not found such case and will add when find real case.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
module.h was included twice.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver causes the following randconfig build error:
drivers/i2c/muxes/i2c-mux-pca954x.c: In function ‘pca954x_probe’:
drivers/i2c/muxes/i2c-mux-pca954x.c:204:2: error: implicit declaration
of function ‘devm_gpiod_get’ [-Werror=implicit-function-declaration]
gpio = devm_gpiod_get(&client->dev, "reset");
^
drivers/i2c/muxes/i2c-mux-pca954x.c:204:7: warning: assignment makes
pointer from integer without a cast [enabled by default]
gpio = devm_gpiod_get(&client->dev, "reset");
^
drivers/i2c/muxes/i2c-mux-pca954x.c:206:3: error: implicit declaration
of function ‘gpiod_direction_output’
[-Werror=implicit-function-declaration]
gpiod_direction_output(gpio, 0);
^
cc1: some warnings being treated as errors
make[3]: *** [drivers/i2c/muxes/i2c-mux-pca954x.o] Error 1
This is because it is getting compiled without gpiolib, so
introduce an explicit dependency.
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes possible issue in case pdev name contains formatting characters.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Reported-by: Kees Cook <keescook@google.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
drivers/i2c/busses/i2c-rk3x.c:610:69-70: rk3x_i2c_match is not NULL terminated at line 610
Make sure of_device_id tables are NULL terminated
Generated by: /kbuild/src/linux/scripts/coccinelle/misc/of_table.cocci
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes:
>> drivers/i2c/busses/i2c-sun6i-p2wi.c:243:10: warning: 'ret' may be used uninitialized in this function [-Wmaybe-uninitialized]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The P2WI controller looks like an SMBus controller which only supports byte
data transfers. But, it differs from standard SMBus protocol on several
aspects:
- it supports only one slave device, and thus drop the address field
- it adds a parity bit every 8bits of data
- only one read access is required to read a byte (instead of a write
followed by a read access in standard SMBus protocol)
- there's no Ack bit after each byte transfer
This means this bus cannot be used to interface with standard SMBus
devices (the only known device to support this interface is the AXP221
PMIC).
However the P2WI protocol is close enough to SMBus to be integrated in
the I2C subsystem (see this thread [1] for detailed reasons that led to
integrating this driver in the I2C subsystem).
[1] http://www.spinics.net/lists/linux-i2c/msg15066.html
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Driver for the native I2C adapter found in Rockchip RK3xxx SoCs.
Configuration is only possible through devicetree. The driver is
interrupt driven and supports the I2C_M_IGNORE_NAK mangling bit.
Signed-off-by: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"I2C has the following updates for 3.16:
- major cleanups to the rcar and sh_mobile drivers
- removal of nuc900 driver which had a compile error for years
- usual bunch of driver updates, bugfixes and cleanups"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (44 commits)
i2c: pca954x: Fix compilation without CONFIG_GPIOLIB
i2c: mux: pca954x: Use the descriptor-based GPIO API
i2c: mpc: insert DR read in i2c_fixup()
i2c: bfin: turn to Resource-managed API in probe function
i2c: Make of_device_id array const
i2c: remove unnecessary OOM messages
i2c: designware-pci: Add Haswell PCI IDs
i2c: designware: Add runtime PM hooks
i2c: designware: Disable device on system suspend
i2c: nuc900: remove driver
i2c: imx: update i2c clock divider for each transaction
i2c: imx: fix the i2c bus hang issue when do repeat restart
i2c: rcar: update copyright and license information
i2c: rcar: janitorial cleanup after refactoring
i2c: rcar: reuse status bits as enable bits
i2c: rcar: remove spinlock
i2c: rcar: refactor status bit handling
i2c: rcar: refactor setting up msg
i2c: rcar: check bus free before first message
i2c: rcar: refactor irq state machine
...
The pca954x driver recently switched to the GPIO descriptor API without
including the correct <linux/gpio/consumer.h> header. This breaks
compilation without CONFIG_GPIOLIB.
drivers/i2c/muxes/i2c-mux-pca954x.c: In function ‘pca954x_probe’:
drivers/i2c/muxes/i2c-mux-pca954x.c:204:2: error: implicit declaration
of function ‘devm_gpiod_get’ [-Werror=implicit-function-declaration]
gpio = devm_gpiod_get(&client->dev, "reset");
^
drivers/i2c/muxes/i2c-mux-pca954x.c:204:7: warning: assignment makes
pointer from integer without a cast [enabled by default]
gpio = devm_gpiod_get(&client->dev, "reset");
^
drivers/i2c/muxes/i2c-mux-pca954x.c:206:3: error: implicit declaration
of function ‘gpiod_direction_output’
[-Werror=implicit-function-declaration]
gpiod_direction_output(gpio, 0);
^
cc1: some warnings being treated as errors
make[3]: *** [drivers/i2c/muxes/i2c-mux-pca954x.o] Error 1
Fix it by including the right header.
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The ID-based GPIO API pushes handling of GPIO polarity to drivers.
Simplify the driver by switching to the descriptor-based GPIO API.
This also fixes a mismatch between the pca954x DT bindings that document
a "reset-gpios" property and the driver that requests a "reset-gpio"
property.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The mpc_i2c_fixup function is called when the bus is not released by a
slave. The function generates 9 pulses that should lead the slave
to release the bus.
The sequence that generates the pulses disables/enables the I2C module
that controls the blocked bus. We have found out on the P2041 SoC that
this could cause the CPU to hang (for a short delay).
To avoid this, this patch introduces a read to the I2CDR register
between the re-enablement of the I2C module in master mode and its
returning to the slave mode instead of the delay (the final delay,
between the pulses is kept), as proposed in procedure from the P2041
reference manual (16.6.2.3), and the other manuals from the mpc83xx and
mpc85xx families.
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On ARM Chromebooks we have a few devices that are accessed by both the
AP (the main "Application Processor") and the EC (the Embedded
Controller). These are:
* The battery (sbs-battery).
* The power management unit tps65090.
On the original Samsung ARM Chromebook these devices were on an I2C
bus that was shared between the AP and the EC and arbitrated using
some extranal GPIOs (see i2c-arb-gpio-challenge).
The original arbitration scheme worked well enough but had some
downsides:
* It was nonstandard (not using standard I2C multimaster)
* It only worked if the EC-AP communication was I2C
* It was relatively hard to debug problems (hard to tell if i2c issues
were caused by the EC, the AP, or some device on the bus).
On the HP Chromebook 11 the design was changed to:
* The AP/EC comms were still i2c, but the battery/tps65090 were no
longer on the bus used for AP/EC communication. The battery was
exposed to the AP through a limited i2c tunnel and tps65090 was
exposed to the AP through a custom Linux driver.
On the Samsung ARM Chromebook 2 the scheme is changed yet again, now:
* The AP/EC comms are now using SPI for faster speeds.
* The EC's i2c bus is exposed to the AP through a full i2c tunnel.
The upstream "tegra124-venice2" uses the same scheme as the Samsung
ARM Chromebook 2, though it has a different set of components on the
other side of the bus.
This driver supports the scheme used by the Samsung ARM Chromebook 2.
Future patches to this driver could add support for the battery tunnel
on the HP Chromebook 11 (and perhaps could even be used to access
tps65090 on the HP Chromebook 11 instead of using a special driver,
but I haven't researched that enough).
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message. For example,
k.alloc and v.alloc failures use dump_stack().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Intel Haswell has the same I2C host controller than Baytrail and it can
also be enumerated as a PCI device. Add the PCI IDs to the driver list.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It is possible that after entering runtime PM suspend the controller
context is lost due the fact that its power is removed. This happens for
example on Asus T100, an Intel Baytrail based tablet/laptop.
In order to get the controller back to functional state, we need to
implement runtime PM hooks which will re-initialize the hardware during
runtime PM resume. We can re-use the existing system suspend hooks as the
steps to resume/suspend the controller are the same.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Userspace can initiate system suspend on arbitrary times which means that
device drivers must make sure that their device gets quiesced before system
suspend is entered. Therefore disable the I2C host controller in the driver
system suspend hook.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Arnd said in another patch:
"As far as I can tell, this driver must have produced this
error for as long as it has been merged into the mainline kernel, but
it was never part of the normal build tests:
drivers/i2c/busses/i2c-nuc900.c: In function 'nuc900_i2c_probe':
drivers/i2c/busses/i2c-nuc900.c:601:17: error: request for member
'apbfreq' in something not a structure or union
ret = (i2c->clk.apbfreq)/(pdata->bus_freq * 5) - 1;
^
This is an attempt to get the driver to build and possibly
work correctly, although I do wonder whether we should just
remove it, as it has clearly never worked."
I agree with removing it since nobody showed interest in Arnd's fixup
patch.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: Wan ZongShun <mcuos.com@gmail.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Since IMX serial SOCs support low bus freq mode, some clocks freq
may change to save power. I2C needs to check the clock source and
update the divider.
For example:
i.MX6SL I2C clk is from IPG_PERCLK which is sourced from IPG_CLK.
Under normal operation, IPG_CLK is 66MHz, ipg_perclk is at 22MHz.
In low bus freq mode, IPG_CLK is at 12MHz and IPG_PERCLK is down
to 4MHz. So the I2C driver must update the divider register for
each transaction when the current IPG_PERCLK is not equal to the
clock of previous transaction.
Signed-off-by: Fugang Duan <B38611@freescale.com>
[wsa: removed an outdated comment and simplified debug output]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Test i2c device Maxim max44009, datasheet is located at:
http://www.maximintegrated.com/datasheet/index.mvp/id/7175
The max44009 support repeat operation like:
read -> repeat restart -> read/write
The current i2c imx host controller driver don't support this
operation that causes i2c bus hang due to "MTX" is cleared in
.i2c_imx_read(). If "read" is the last message there have no problem,
so the current driver supports all SMbus operation like:
write -> repeat restart -> read/write
IMX i2c controller for master receiver has some limitation:
- If it is the last byte for one operation, it must generate STOP
signal before read I2DR to prevent controller from generating another
clock cycle.
- If it is the last byte in the read, and then do repeat restart, it must
set "MTX" before read I2DR to prevent controller from generating another
extra clock cycle.
The patch is to fix the issue.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make clear that the driver is GPL v2 only. Remove FSF address. Remove
filename in comment. Update copyright information.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Remove some obvious comments, remove some superfluous debug output (the
error code carries the same information), some white space fixing...
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Status register and enable register are identical regarding their
layout. Use the bit definitions for both.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c core has per-adapter locks, so no need to protect again.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The old macros made it harder to see what was actually happening.
Replace them with something more readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Setting up a read or write message is similar enough to be done in one
function. Also, move a helper function into the new function since it is
only used here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We should always check if the bus is free, independently if it is a read
or write. It should be done before the first message, though. After
that, we ourselves keep the bus busy. Remove a 'ret' assignment which
only silenced a build warning.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Remove the seperate functions and use designated constants. As readable
but less overhead. Actually, this is even more readable since the old
function used a mix of "=" and "|=".
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Remove the seperate functions and use designated constants. As readable
but less overhead.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We use devm, so irq number is only needed during probe.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Very basic operations, just called once, can also go to the caller.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use devm_gpio_request() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Violeta Menendez <violeta.menendez@codethink.co.uk>
Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
Tested-by: Violeta Menendez <violeta.menendez@codethink.co.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c-eg20t driver is for a companion chip to the Intel Atom E600
series processors. These are 32-bit x86 processors so the driver is
only needed on X86_32. Add COMPILE_TEST as an alternative, so that the
driver can still be build-tested elsewhere.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Newer SoCs have so fast input clocks that the ICCL/H registers only
count every second clock to have a meaningful 9-bit range. The driver
was already prepared for that happening, but didn't use it so far.
Add the proper DT configuration for SoCs that need it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Due to misconfiguration, it can happen that the calculated timing
parameters are out of range. Bail out if that happens. We can also
simplify some logic later because of the verified value. Also, make the
printouts of the values more precise by adding the hex-prefixes.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
sh_mobile_i2c_init() could detect wrong settings, but didn't bail out,
so it would continue unconfigured. Fix this.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Following the KISS principle, remove unneeded stuff.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This is what devm was made for. No rollback mechanism needed, remove the
hook parameter from the irq setup function and simplify it. While we are
here change some variables to proper types.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Convert the easy parts to devm. irqs will be converted in a seperate
patch to keep diffs readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use standard i2c error codes for i2c failures. Also, don't print
something on timeout since it happens regularly with i2c. Simplify some,
logic, too.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
No functional change, binaries are identical.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
HSI2C module on Exynos5260 differs from current modules in
following ways:
1. HSI2C on Exynos5260 has fifo_depth of 16bytes
2. Module needs to be reset as a part of init sequence.
Hence, Following changes are involved.
1. Add a new compatible string and Updates the Documentation dt bindings.
2. Introduce a variant struct to support the changes in H/W
3. Reset the module during init. Thus, bringing the module back
to default state irrespective of what firmware did with it.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixed most checkpatch.pl issues
Signed-off-by: Richard Leitner <me@g0hl1n.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
For !CONFIG_PM_RUNTIME, the device were never put back into active
state while resuming.
For CONFIG_PM_RUNTIME, we blindly trusted the device to be inactive
while we were about to handle it at suspend late, which is just too
optimistic.
Even if the driver uses pm_runtime_put_sync() after each tranfer to
return it's runtime PM resources, there are no guarantees this will
actually mean the device will inactivated. The reason is that the PM
core will prevent runtime suspend during system suspend, and thus when
a transfer occurs during the early phases of system suspend the device
will be kept active after the transfer.
To handle both issues above, use pm_runtime_force_suspend|resume() from
the system suspend|resume callbacks.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The smbus block read is not currently supported for imx i2c devices.
This patchset adds the support to imx i2c bus so that blocks of data
can be read using SMbus block reads.(using i2c_smbus_read_block_data()
function from the i2c_core.c.). Tested with 3.10.9 kernel.
Reviewed-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Kaushal Butala <kaushalkernelmailinglist@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Allwinner A10 compatibles were following a slightly different compatible
patterns than the rest of the SoCs for historical reasons. Move to the other
pattern for consistency across all Allwinner Socs.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[wsa: dropped binding OK as per
http://lists.infradead.org/pipermail/linux-arm-kernel/2014-February/229438.html]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This hardware does not support zero length transfers. Instead, the
driver does one (random) byte transfers currently with undefined results
for the slaves. We now bail out.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
This patch corrects the error check on the call to pm_runtime_get_sync.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Reviewed-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Don't unmark the device as suspended until after it's been re-setup.
The main race would be w.r.t. an i2c driver that gets resumed at the same
time (asyncronously), that is allowed to do a transfer since suspended
is set to 0 before reinit, but really should have seen the -EIO return
instead.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
There have been "i2c_designware 80860F41:00: controller timed out" errors
on a number of Baytrail platforms. The issue is caused by incorrect value in
Interrupt Mask Register (DW_IC_INTR_MASK) when i2c core is being enabled.
This causes call to __i2c_dw_enable() to immediately start the transfer which
leads to timeout. There are 3 failure modes observed:
1. Failure in S0 to S3 resume path
The default value after reset for DW_IC_INTR_MASK is 0x8ff. When we start
the first transaction after resuming from system sleep, TX_EMPTY interrupt
is already unmasked because of the hardware default.
2. Failure in normal operational path
This failure happens rarely and is hard to reproduce. Debug trace showed that
DW_IC_INTR_MASK had value of 0x254 when failure occurred, which meant
TX_EMPTY was unmasked.
3. Failure in S3 to S0 suspend path
This failure also happens rarely and is hard to reproduce. Adding debug trace
that read DW_IC_INTR_MASK made this failure not reproducible. But from ISR
call trace we could conclude TX_EMPTY was unmasked when problem occurred.
The patch masks all interrupts before the controller is enabled to resolve the
faulty DW_IC_INTR_MASK conditions.
Signed-off-by: Wenkai Du <wenkai.du@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[wsa: improved the comment and removed typo in commit msg]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Pull i2c updates from Wolfram Sang:
"Here is the pull request from the i2c subsystem. It got a little
delayed because I needed to wait for a dependency to be included
(commit b424080a9e: "reset: Add optional resets and stubs"). Plus,
I had some email problems. All done now, the highlights are:
- drivers can now deprecate their use of i2c classes. That shouldn't
be used on embedded platforms anyhow and was often blindly
copy&pasted. This mechanism gives users time to switch away and
ultimately boot faster once the use of classes for those drivers is
gone for good.
- new drivers for QUP, Cadence, efm32
- tracepoint support for I2C and SMBus
- bigger cleanups for the mv64xxx, nomadik, and designware drivers
And the usual bugfixes, cleanups, feature additions. Most stuff has
been in linux-next for a while. Just some hot fixes and new drivers
were added a bit more recently."
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (63 commits)
i2c: cadence: fix Kconfig dependency
i2c: Add driver for Cadence I2C controller
i2c: cadence: Document device tree bindings
Documentation: i2c: improve section about flags mangling the protocol
i2c: qup: use proper type fro clk_freq
i2c: qup: off by ones in qup_i2c_probe()
i2c: efm32: fix binding doc
MAINTAINERS: update I2C web resources
i2c: qup: New bus driver for the Qualcomm QUP I2C controller
i2c: qup: Add device tree bindings information
i2c: i2c-xiic: deprecate class based instantiation
i2c: i2c-sirf: deprecate class based instantiation
i2c: i2c-mv64xxx: deprecate class based instantiation
i2c: i2c-designware-platdrv: deprecate class based instantiation
i2c: i2c-davinci: deprecate class based instantiation
i2c: i2c-bcm2835: deprecate class based instantiation
i2c: mv64xxx: Fix reset controller handling
i2c: omap: fix usage of IS_ERR_VALUE with pm_runtime_get_sync
i2c: efm32: new bus driver
i2c: exynos5: remove unnecessary cast of void pointer
...
If the renamed symbol is defined lib/iomap.c implements ioport_map and
ioport_unmap and currently (nearly) all platforms define the port
accessor functions outb/inb and friend unconditionally. So
HAS_IOPORT_MAP is the better name for this.
Consequently NO_IOPORT is renamed to NO_IOPORT_MAP.
The motivation for this change is to reintroduce a symbol HAS_IOPORT
that signals if outb/int et al are available. I will address that at
least one merge window later though to keep surprises to a minimum and
catch new introductions of (HAS|NO)_IOPORT.
The changes in this commit were done using:
$ git grep -l -E '(NO|HAS)_IOPORT' | xargs perl -p -i -e 's/\b((?:CONFIG_)?(?:NO|HAS)_IOPORT)\b/$1_MAP/'
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During development, the driver first really needed to depend on
COMMON_CLK only. Later, it was switched to writel_relaxed, but it was
forgotten to update the dependencies, so build errors occured:
config: make ARCH=i386 allyesconfig
All error/warnings:
drivers/i2c/busses/i2c-cadence.c: In function 'cdns_i2c_clear_bus_hold':
>> drivers/i2c/busses/i2c-cadence.c:168:3: error: implicit declaration
>> of function 'writel_relaxed' [-Werror=implicit-function-declaration]
Use a very safe dependency for now.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add a driver for the Cadence I2C controller. This controller is for
example found in Xilinx Zynq.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It is used with of_property_read_u32(), so it should be u32.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Fixes: 10c5a84259 ('i2c: qup: New bus driver for the Qualcomm QUP I2C controller')
These should ">= ARRAY_SIZE()" instead of "> ARRAY_SIZE()".
Fixes: 10c5a84259 ('i2c: qup: New bus driver for the Qualcomm QUP I2C controller')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This bus driver supports the QUP i2c hardware controller in the Qualcomm SOCs.
The Qualcomm Universal Peripheral Engine (QUP) is a general purpose data path
engine with input/output FIFOs and an embedded i2c mini-core. The driver
supports FIFO mode (for low bandwidth applications) and block mode (interrupt
generated for each block-size data transfer).
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Reviewed-by: Andy Gross <agross@codeaurora.org>
Tested-by: Philip Elcan <pelcan@codeaurora.org>
[wsa: removed needless IS_ERR_VALUE]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Warn users that class based instantiation is going away soon in favour
of more robust probing and faster bootup times.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Warn users that class based instantiation is going away soon in favour
of more robust probing and faster bootup times.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: Barry Song <baohua@kernel.org>
Warn users that class based instantiation is going away soon in favour
of more robust probing and faster bootup times.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Warn users that class based instantiation is going away soon in favour
of more robust probing and faster bootup times.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Warn users that class based instantiation is going away soon in favour
of more robust probing and faster bootup times.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Warn users that class based instantiation is going away soon in favour
of more robust probing and faster bootup times.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The reset framework recently gained optional stubs when CONFIG_RESET_CONTROLLER
is not selected. It also introduced a function reset_get_optional, that is also
dummy-defined whenever the framework isn't enabled, for drivers that needs an
optional reset controller.
Switch to this function, since the mv64xxx driver is in this case. This also
fixes a compilation breakage whenever the reset framework wasn't selected:
drivers/i2c/busses/i2c-mv64xxx.c:771:2: error: implicit declaration of function 'devm_reset_control_get'
While we're at it, remove the redundant test on dev.of_node surrounding the
calls to reset framework functions, since it will either be a valid pointer, an
error pointer in the case where we called reset_get_optional without an of_node
pointer or if it failed, or NULL if we're not loaded through DT.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
we use IS_ERR_VALUE to check for error values of pm_runtime_get_sync,
when the value can only be < 0 in the case of err. Replace the
check with a simpler < 0 check.
This fixes the coccicheck warnings:
linux-2.6/drivers/i2c/busses/i2c-omap.c:1157:5-24:
pm_runtime_get_sync returns < 0 as error. Unecessary IS_ERR_VALUE at
line 1158
linux-2.6/drivers/i2c/busses/i2c-omap.c:1278:7-26:
pm_runtime_get_sync returns < 0 as error. Unecessary IS_ERR_VALUE at
line 1279
drivers/i2c/busses/i2c-omap.c:638:5-24:
pm_runtime_get_sync returns < 0 as error. Unecessary IS_ERR_VALUE at
line 639
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This was tested on a EFM32GG-DK3750 devboard that has a temperature
sensor and an eeprom on its i2c bus.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes a build break due to the undeclared use of irq_of_parse_and_map()
and of_iomap(). This build break was apparently introduced while the
driver was unbuildable due to the bug fixed by
62c19c9d29 ("i2c: Remove usage of
orphaned symbol OF_I2C"). When 62c19c was added in v3.14-rc7,
the driver was enabled again, breaking the powerpc mpc85xx_defconfig
and mpc85xx_smp_defconfig.
62c19c is marked for stable, so this should go there as well.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
The symbol is an orphan, don't depend on it anymore.
Signed-off-by: Richard Weinberger <richard@nod.at>
[wsa: enhanced commit message]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: 687b81d083 (i2c: move OF helpers into the core)
Cc: stable@kernel.org
Remove unnecessary cast of void pointer, because 'algo_data' of
'struct i2c_adapter' is a void pointer. Casting the void pointer
is redundant. The conversion from void pointer to any other
pointer type is guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SIMPLE_DEV_PM_OPS are only used when
the CONFIG_PM_SLEEP is enabled.
warning: 'exynos5_i2c_suspend_noirq' defined but not used [-Wunused-function]
warning: 'exynos5_i2c_resume_noirq' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When using device-tree and the i2c-gpio driver is called before the
GPIO node has been probed then it needs to correctly defer the probe
instead of returning a permanent error that the gpio numbers are not
valid.
This fixes the following error:
/i2c@2: invalid GPIO pins, sda=-517/scl=-517
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The SMBUS tracepoints can be enabled thusly:
echo 1 >/sys/kernel/debug/tracing/events/i2c/enable
and will dump messages that can be viewed in /sys/kernel/debug/tracing/trace
that look like:
... smbus_read: i2c-0 a=051 f=0000 c=fa BYTE_DATA
... smbus_reply: i2c-0 a=051 f=0000 c=fa BYTE_DATA l=1 [39]
... smbus_result: i2c-0 a=051 f=0000 c=fa BYTE_DATA rd res=0
formatted as:
i2c-<adapter-nr>
a=<addr>
f=<flags>
c=<command>
<protocol-name>
<rd|wr>
res=<result>
l=<data-len>
[<data-block>]
The adapters to be traced can be selected by something like:
echo adapter_nr==1 >/sys/kernel/debug/tracing/events/i2c/filter
Note that this shares the same filter and enablement as i2c.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add tracepoints into the I2C message transfer function to retrieve the message
sent or received. The following config options must be turned on to make use
of the facility:
CONFIG_FTRACE
CONFIG_ENABLE_DEFAULT_TRACERS
The I2C tracepoint can be enabled thusly:
echo 1 >/sys/kernel/debug/tracing/events/i2c/enable
and will dump messages that can be viewed in /sys/kernel/debug/tracing/trace
that look like:
... i2c_write: i2c-5 #0 a=044 f=0000 l=2 [02-14]
... i2c_read: i2c-5 #1 a=044 f=0001 l=4
... i2c_reply: i2c-5 #1 a=044 f=0001 l=4 [33-00-00-00]
... i2c_result: i2c-5 n=2 ret=2
formatted as:
i2c-<adapter-nr>
#<message-array-index>
a=<addr>
f=<flags>
l=<datalen>
n=<message-array-size>
ret=<result>
[<data>]
The operation is done between the i2c_write/i2c_read lines and the i2c_reply
and i2c_result lines so that if the hardware hangs, the trace buffer can be
consulted to determine the problematic operation.
The adapters to be traced can be selected by something like:
echo adapter_nr==1 >/sys/kernel/debug/tracing/events/i2c/filter
These changes are based on code from Steven Rostedt.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
[wsa: adapted path for 'enable' in the commit msg]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is a rather odd feature of the exynos i2c controller that if it
is left enabled, it can lock itself up with the clk line held low.
This makes the bus unusable.
Unfortunately, the s3c24xx_i2c_set_master() function does not notice
this, and reports a timeout. From then on the bus cannot be used until
the AP is rebooted.
The problem happens when any sort of interrupt occurs (e.g. due to a
bus transition) when we are not in the middle of a transaction. We
have seen many instances of this when U-Boot leaves the bus apparently
happy, but Linux cannot access it.
The current code is therefore pretty fragile.
This fixes things by leaving the bus disabled unless we are actually
in a transaction. We enable the bus at the start of the transaction and
disable it at the end. That way we won't get interrupts and will not
lock up the bus.
It might be possible to clear pending interrupts on start-up, but this
seems to be a more robust solution. We can't service interrupts when
we are not in a transaction, and anyway would rather not lock up the
bus while we try.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Warn users that class based instantiation is going away soon in favour
of more robust probing and faster bootup times.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
This adds the ability to set "clock-frequency" in the device tree for the at91
i2cbus following the naming of other i2c bus implementations. If the property
is not set,the clock frequency will default to the previously used define
of 100KHz.
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On Intel BayTrail, there was case whereby the resulting fast mode
bus speed becomes slower (~20% slower compared to expected speed)
if using the HCNT/LCNT calculated in the core layer. Thus, this
patch is added to allow pci glue layer to pass in optimal
HCNT/LCNT/SDA hold time values to core layer since the core
layer supports cofigurable HCNT/LCNT/SDA hold time values now.
Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch fixes the error returned to the i2c_transfer function
to -EAGAIN in case of arbitratin lost, so that the retry mechanism
can be used.
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We now have a central place to put this code to.
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Calling the state machine with a definite state which is only used in
this context is superfluous. Do it directly.
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
For start and restart, we are doing the same thing. Let's consolidate
that.
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
All the I2C controllers on Intel BayTrail LPSS subsystem able
to support 10-bit addressing mode functionality.
Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Signed-off-by: Ong, Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use devm_ioremap_resource() in order to make the code simpler,
and remove redundant return value check of platform_get_resource()
because the value is checked by devm_ioremap_resource().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use devm_ioremap_resource() in order to make the code simpler,
and remove redundant return value check of platform_get_resource()
because the value is checked by devm_ioremap_resource().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add Device ID of Intel BayTrail SMBus Controller.
Signed-off-by: Chew, Kean ho <kean.ho.chew@intel.com>
Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
