Decouple the HSMMC glue from the twl4030 as the only
regulator provider, using the regulator framework instead.
This makes the glue's "mmc-twl4030" name become a complete
misnomer ... this code could probably all migrate into the
HSMMC driver now.
Tested on 3430SDP (SD and low-voltage MMC) and Beagle (SD),
plus some other boards (including Overo) after they were
converted to set up MMC regulators properly.
Eventually all boards should just associate a regulator with
each MMC controller they use. In some cases (Overo MMC2 and
Pandora MMC3, at least) that would be a fixed-voltage regulator
with no real software control. As a temporary hack (pending
regulator-next updates to make the "fixed.c" regulator become
usable) there's a new ocr_mask field for those boards.
Patch updated with a fix for disabling vcc_aux by
Adrian Hunter <adrian.hunter@nokia.com>
Cc: Pierre Ossman <drzeus-list@drzeus.cx>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Until now we have had a 1:1 mapping between storage device physical
block size and the logical block sized used when addressing the device.
With SATA 4KB drives coming out that will no longer be the case. The
sector size will be 4KB but the logical block size will remain
512-bytes. Hence we need to distinguish between the physical block size
and the logical ditto.
This patch renames hardsect_size to logical_block_size.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The second argument of the probe method points to the amba_id
structure, so it's better passed with the correct type. None of the
current in-tree drivers uses the pointer, so they have only been
checked for a clean compile.
Change suggested by Russell King.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move all the gpio functions out of <mach/hardware.h> as
this file is for defining the generic IO base addresses
for the kernel IO calls.
Make a new header <mach/gpio-fns.h> to take this and
include it via the chain from <linux/gpio.h> which is
what most of these files should be using (and will be
changed as soon as possible).
Note, this does make minor changes to some drivers but
should not mess up any pending merges.
CC: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CC: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Till now block layer allowed two separate modes of request execution.
A request is always acquired from the request queue via
elv_next_request(). After that, drivers are free to either dequeue it
or process it without dequeueing. Dequeue allows elv_next_request()
to return the next request so that multiple requests can be in flight.
Executing requests without dequeueing has its merits mostly in
allowing drivers for simpler devices which can't do sg to deal with
segments only without considering request boundary. However, the
benefit this brings is dubious and declining while the cost of the API
ambiguity is increasing. Segment based drivers are usually for very
old or limited devices and as converting to dequeueing model isn't
difficult, it doesn't justify the API overhead it puts on block layer
and its more modern users.
Previous patches converted all block low level drivers to dequeueing
model. This patch completes the API transition by...
* renaming elv_next_request() to blk_peek_request()
* renaming blkdev_dequeue_request() to blk_start_request()
* adding blk_fetch_request() which is combination of peek and start
* disallowing completion of queued (not started) requests
* applying new API to all LLDs
Renamings are for consistency and to break out of tree code so that
it's apparent that out of tree drivers need updating.
[ Impact: block request issue API cleanup, no functional change ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: unsik Kim <donari75@gmail.com>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Laurent Vivier <Laurent@lvivier.info>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Stefan Weinhuber <wein@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
plat-omap/mailbox, floppy, viocd, mspro_block, i2o_block and
mmc/card/queue are already pretty close to dequeueing model and can be
converted with simple changes. Convert them.
While at it,
* xen-blkfront: !fs check moved downwards to share dequeue call with
normal path.
* mspro_block: __blk_end_request(..., blk_rq_cur_byte()) converted to
__blk_end_request_cur()
* mmc/card/queue: loop of __blk_end_request() converted to
__blk_end_request_all()
[ Impact: dequeue in-flight request ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
With recent cleanups, there is no place where low level driver
directly manipulates request fields. This means that the 'hard'
request fields always equal the !hard fields. Convert all
rq->sectors, nr_sectors and current_nr_sectors references to
accessors.
While at it, drop superflous blk_rq_pos() < 0 test in swim.c.
[ Impact: use pos and nr_sectors accessors ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Tested-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Mike Miller <mike.miller@hp.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Eric Moore <Eric.Moore@lsi.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Dario Ballabio <ballabio_dario@emc.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: unsik Kim <donari75@gmail.com>
Cc: Laurent Vivier <Laurent@lvivier.info>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
arch-imx is superseeded by the MXC architecture support.
This patch removes arch-imx from the build system.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
mvsdio: fix CONFIG_PM=y build
mmci: fix crash with debug enabled
sdhci: catch ADMA errors
mmc: increase power up delay
sdhci-pci: bad error handling in probe function
mmc_block: be prepared for oversized requests
Fix usage of obsolete parameters and functions in the driver's PM
callbacks.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
If MMC debugging is enabled, the mmci driver oopses because the DBG
macro uses host->mmc before it is set. Set it earlier.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
The TI controller on Toshiba Tecra M5 needs more time to power up or
the cards will init incorrectly or not at all.
Signed-off-by: José M. Fernández <josemariafg@gmail.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
The goto unmap is too early, we haven't allocated host or done the
request_region().
Found by smatch (http://repo.or.cz/w/smatch.git).
[ Second error path fix by Pierre Ossman ]
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
The block layer does not support very low sector count restrictions
so we need to be prepared to handle bigger requests than we can send
directly to the controller.
Problem found by Manuel Lauss.
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
calls
The S3C24XX DMA API channel configuration registers are being passed
values comprised of register values which makes it hard to move the
API to cover both the S3C24XX and S3C64XX.
These values can be calculated from knowing which device the channel
is connected to, so remove them from the two calls s3c2410_dma_config
and s3c2410_dma_devconfig.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Same patch as before, modified to use bool. Also adds description of
the new field in struct atmel_mci that I missed in the first patch.
This patch adds Atmel MCI support for inverted detect pins.
Signed-off-by: Jonas Larsson <jonas.larsson@martinsson.se>
Acked-by: Pierre Ossman <pierre@ossman.eu>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
A very large subset of SD cards in the market send their
responses and data non-byte-aligned. So add logic to the
mmc spi driver to handle this mess.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
With spurious interrupt cmd can be null even when we have CC
set in irq status.
Fixes: NB#106295 - prevent potential kernel crash in the MMC driver
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
This fixes the issue noted by Russell King:
drivers/mmc/host/omap_hsmmc.c: In function 'mmc_omap_xfer_done':
drivers/mmc/host/omap_hsmmc.c:301: error: implicit declaration of function 'mmc_omap_fclk_lazy_disable'
This got broken by 4a694dc915.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
SD/MMC card timeouts can be very high. So avoid busy-waiting,
using the scheduler. Calculate all timeouts in jiffies units,
because this will give us the correct sign when to involve
the scheduler.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Some cards are not able to calculate a valid CRC16 value
for CID and CSD reads (CRC for 512 byte data blocks is OK).
By moving the CRC enable after the read of CID and CSD, these
cards can be used. This patch was tested with a faulty 8 GByte
takeMS Class 6 SDHC card. This patch was suggested by
Pierre Ossman.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
Spurious IRQs seen on MMC after 2.6.29. Flush posted write in IRQ
handler.
The interrupt line is released by clearing the error status bits
in the MMCHS_STAT register, which must occur before the interrupt
handler returns to avoid unwanted irqs. Hence the need to flush
the posted write.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Tony Lindgen <tony@atomide.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
DMA request source (RSSR) needs to be set only once (in probe).
DMA burst length (BLR) need to be set only in set_ios()
This cleans up imxmci_setup_data() and should make it a little
bit faster :)
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Add __init __exit for appropriate probe and remove functions.
Conver to platform_driver_probe()
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (42 commits)
atmel-mci: fix sdc_reg typo
tmio_mmc: add maintainer
mmc: Add OpenFirmware bindings for SDHCI driver
sdhci: Add quirk for forcing maximum block size to 2048 bytes
sdhci: Add quirk for controllers that need IRQ re-init after reset
sdhci: Add quirk for controllers that need small delays for PIO
sdhci: Add set_clock callback and a quirk for nonstandard clocks
sdhci: Add get_{max,timeout}_clock callbacks
sdhci: Add support for hosts reporting inverted write-protect state
sdhci: Add support for card-detection polling
sdhci: Enable only relevant (DMA/PIO) interrupts during transfers
sdhci: Split card-detection IRQs management from sdhci_init()
sdhci: Add support for bus-specific IO memory accessors
mmc_spi: adjust for delayed data token response
omap_hsmmc: Wait for SDBP
omap_hsmmc: Fix MMC3 dma
omap_hsmmc: Disable SDBP at suspend
omap_hsmmc: Do not prefix slot name
omap_hsmmc: Allow cover switch to cause rescan
omap_hsmmc: Add 8-bit bus width mode support
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
trivial: Update my email address
trivial: NULL noise: drivers/mtd/tests/mtd_*test.c
trivial: NULL noise: drivers/media/dvb/frontends/drx397xD_fw.h
trivial: Fix misspelling of "Celsius".
trivial: remove unused variable 'path' in alloc_file()
trivial: fix a pdlfush -> pdflush typo in comment
trivial: jbd header comment typo fix for JBD_PARANOID_IOFAIL
trivial: wusb: Storage class should be before const qualifier
trivial: drivers/char/bsr.c: Storage class should be before const qualifier
trivial: h8300: Storage class should be before const qualifier
trivial: fix where cgroup documentation is not correctly referred to
trivial: Give the right path in Documentation example
trivial: MTD: remove EOL from MODULE_DESCRIPTION
trivial: Fix typo in bio_split()'s documentation
trivial: PWM: fix of #endif comment
trivial: fix typos/grammar errors in Kconfig texts
trivial: Fix misspelling of firmware
trivial: cgroups: documentation typo and spelling corrections
trivial: Update contact info for Jochen Hein
trivial: fix typo "resgister" -> "register"
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6: (32 commits)
regulator: twl4030 VAUX3 supports 3.0V
regulator: Support disabling of unused regulators by machines
regulator: Don't increment use_count for boot_on regulators
twl4030-regulator: expose VPLL2
regulator: refcount fixes
regulator: Don't warn if we failed to get a regulator
regulator: Allow boot_on regulators to be disabled by clients
regulator: Implement list_voltage for WM835x LDOs and DCDCs
twl4030-regulator: list more VAUX4 voltages
regulator: Don't warn on omitted voltage constraints
regulator: Implement list_voltage() for WM8400 DCDCs and LDOs
MMC: regulator utilities
regulator: twl4030 voltage enumeration (v2)
regulator: twl4030 regulators
regulator: get_status() grows kerneldoc
regulator: enumerate voltages (v2)
regulator: Fix get_mode() for WM835x DCDCs
regulator: Allow regulators to set the initial operating mode
regulator: Suggest use of datasheet supply or pin names for consumers
regulator: email - update email address and regulator webpage.
...
Glue between MMC and regulator stacks ... verified with
some OMAP3 boards using adjustable and configured-as-fixed
regulators on several MMC controllers.
These calls are intended to be used by MMC host adapters
using at least one regulator per host. Examples include
slots with regulators supporting multiple voltages and
ones using multiple voltage rails (e.g. DAT4..DAT7 using a
separate supply, or a split rail chip like certain SDIO
WLAN or eMMC solutions).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This fixes a bug when setting the sdc_reg for 4-bit bus width
transactions.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch adds a new driver: sdhci-of. The driver is similar to
the sdhci-pci, it contains common probe code, and controller-specific
ops and quirks.
So far there are only Freescale eSDHC ops and quirks.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
FSL eSDHC controllers can support maximum block size up to 4096 bytes,
the MBL (Maximum Block Length) field in the capabilities register
extended by one bit, and is set to 0x3.
But the SDHCI core doesn't support blocks of 4096 bytes, and thus
forces blksz to the lowest value -- 512 bytes. With this patch we can
pin up the blksz to the maximum supported block size, i.e. 2048 bytes.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
FSL eSDHC controllers losing signal/interrupt enable states after
reset, so we should re-enable them.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Small udelay is needed to make eSDHC work in PIO mode. Without
the delay reading causes endless interrupt storm, and writing
corrupts data. The first guess would be that we must wait for
some bit in some register, but I didn't find any reliable bits
that change before and after the delay.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
FSL eSDHC hosts have incompatible register map to manage the SDCLK.
This patch adds set_clock callback so that drivers could overwrite
set_clock behaviour.
Similar patch[1] was posted by Ben Dooks, though in Ben's version the
callback is named change_clock, plus the patch has some unrelated bits
that makes the patch difficult to reuse.
[1] http://lkml.org/lkml/2008/12/2/160
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some controllers do not provide clock information in their capabilities
(in the Samsung case, it is because there are multiple clock sources
available to the controller). Add hooks to allow the system to supply
clock information.
p.s.
In the original Ben's patch there was a bug that makes sdhci_add_host()
return -ENODEV even if callbacks were specified. This is fixed now.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch adds SDHCI_QUIRK_INVERTED_WRITE_PROTECT quirk. When
specified, the sdhci driver will invert WP state.
p.s. Actually, the quirk is more board-specific than
controller-specific.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch adds SDHCI_QUIRK_BROKEN_CARD_DETECTION quirk. When specified,
sdhci driver will set MMC_CAP_NEEDS_POLL MMC host capability, and won't
enable card insert/remove interrupts.
This is needed for hosts with unreliable card detection, such as FSL
eSDHC. The original eSDHC driver was tring to "debounce" card-detection
IRQs by reading present state and disabling particular interrupts. But
with this debouncing scheme I noticed that sometimes we miss card
insertion/removal events.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some hosts (that is, FSL eSDHC) throw PIO interrupts during DMA
transfers, this causes tons of unneeded interrupts, and thus highly
degraded speed.
This patch modifies the driver so that now we only enable relevant
(DMA or PIO) interrupts during transfers.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Card detection interrupts should be handled separately as they should
not be enabled before mmc_add_host() returns and should be disabled
before calling mmc_remove_host(). The same is for suspend and resume
routines.
sdhci_init() no longer enables card-detection irqs. Instead, two new
functions implemented: sdhci_enable_card_detection() and
sdhci_disable_card_detection().
New sdhci_reinit() call implemented to behave the same way as the old
sdhci_init().
Also, this patch implements and uses few new helpers to manage IRQs in
a more conveinient way, that is:
- sdhci_clear_set_irqs()
- sdhci_unmask_irqs()
- sdhci_mask_irqs()
- SDHCI_INT_ALL_MASK constant
sdhci_enable_sdio_irq() converted to these new helpers, plus the
helpers will be used by the subsequent patches.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Currently the SDHCI driver works with PCI accessors (write{l,b,w} and
read{l,b,w}).
With this patch drivers may change memory accessors, so that we can
support hosts with "weird" IO memory access requirments.
For example, in "FSL eSDHC" SDHCI hardware all registers are 32 bit
width, with big-endian addressing. That is, readb(0x2f) should turn
into readb(0x2c), and readw(0x2c) should be translated to
le16_to_cpu(readw(0x2e)).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some cards are not able to send the data token in time, but
miss the time frame for some bits(!). So synchronize to the
start of the token.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
It is necessary to wait for bus power before sending
any commands.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Data transfers on third OMAP3 MMC controller don't work
because DMA line numbers are only defined for MMC1 and MMC2.
Fix that and store line numbers in mmc_omap_host structure
to reduce code size.
Tested on OMAP3 pandora board.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Turn off the bus power at suspend.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Allow slot_name to be the same as the other OMAP
driver, by removing the redundant "slot:" prefix.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Allow a cover switch to be used to cause a rescan of the
MMC slot.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Instead of using the bounce buffer, using scatter-gather emulation
(as in the OMAP1/2 MMC driver) removes the need of one extra memory
copy and improves performance.
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some MMC commands result in the card becoming busy after
the response is received. This needs to be specified
for the omap_hsmmc host controller, which is what this
patch does. However, the effect is that some commands
with no data will cause a Transfer Complete (TC) interrupt
in addition to the Command Complete (CC) interrupt.
In order to deal with that, the irq handler has needed
a few changes also.
The benefit of this change is that the omap_hsmmc host
controller driver now waits for the TC interrupt while
the card is busy, so the mmc_block driver needs to poll
the card status just once instead of repeatedly.
i.e. the net result is more sleep and less cpu.
The command sequence for open-ended multi-block write
with DMA is now:
Issue write command CMD25
Receive CC interrupt
Data is sent
Receive TC interrupt (DMA is done)
Issue stop command CMD12
Receive CC interrupt
Card is busy
Receive TC interrupt
Card is now ready for next transfer
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This supports MMC/SD/SDIO currently found on the Kirkwood 88F6281 and
88F6192 SoC controllers.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
drivers/mmc/host/tmio_mmc.h: In function 'tmio_mmc_kmap_atomic':
drivers/mmc/host/tmio_mmc.h:147: error: implicit declaration of function 'kmap_atomic'
drivers/mmc/host/tmio_mmc.h:147: error: 'KM_BIO_SRC_IRQ' undeclared (first use in this function)
drivers/mmc/host/tmio_mmc.h: In function 'tmio_mmc_kunmap_atomic':
drivers/mmc/host/tmio_mmc.h:153: error: implicit declaration of function 'kunmap_atomic'
drivers/mmc/host/tmio_mmc.h:153: error: 'KM_BIO_SRC_IRQ' undeclared (first use in this function)
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Update the tmio_mmc code to call mmc_free_host() when
done using the private data. Without this fix the driver
frees memory and then keeps on using it as private data.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Update the tmio_mmc code to use resource_size(). With this
patch applied the correct resource size is passed to ioremap().
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some SD cards have very high timeouts in SPI mode.
So adjust the timeouts from theory to practice.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some cards are slower than the standard allows and need more
time to respond to a command. Max. observed number of bytes
was 12.
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Allow the platform data structures to specify spi mode 3
(if there is a pullup on the clock line or the spi hardware
is not able to serve spi mode 0).
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
During mmc unsafe resume, choose the right voltage for the card after
powerup.
Although this has not seen to cause trouble, it's the wrong behaviour.
Signed-off-by: Balaji Rao <balajirrao@openmoko.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Most registers lose its state when the processor wakes up from sleep state.
Thus registers should be initialized, when the processor wakes up. However the
current hsmmc 'resume' function doesn't consider this issue and finally makes
deadlock. So this patch fixes this problem.
Signed-off-by: Kim Kyuwon <chammoru@gmail.com>
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Remove code that turns MMC1 power back on after it
has been powered off (when the voltage is 1.8V).
The offending code is not necessary because the
host controller bus voltage is initialized to
3V when probing or resuming. Note that MMC powers up
with the highest voltage available (see mmc_power_up())
which will be 3V also.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Extended CSD is a MMC card register. As increasingly interesting
fields are being added to Extended CSD, it is helpful to see its
value. Note that SD cards do not have an Extended CSD
register, so it is MMC only.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Currently we are using an explicit udev rule to trigger loading of the
mmc-block module when an MMC or SD card is detected:
SUBSYSTEM=="mmc", RUN+="/sbin/modprobe -Qba mmc-block"
It makes much more sense for the mmc bus driver and the mmc-block module to
share MODALIAS information so that they are linked automatically.
There is no real information of use in the MMC system at the current time.
All devices inserted require us to load the mmc-block device. Until such
time as useful parameters exist simply reflect the module linkage via
the module alias below:
mmc:block
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The delayed work item mmc_host.detect is now cancelled before flushing
the work queue. This takes care of cases when delayed_work was scheduled
for mmc_host.detect, but not yet placed in the work queue.
Signed-off-by: Jorg Schummer <ext-jorg.2.schummer@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The s3cmci driver is calling s3c2410_dma_config with incorrect data for
the DCON register. The S3C2410_DCON_HWTRIG is implicit in the channel
configuration and the device selection of S3C2410_DCON_CH0_SDI is
incorrect as the DMA system may not select channel 0.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds __devinit and __devexit macros to the module probe and
remove functions in MMCI. Now includes the __devexit_p() thing too.
Signed-off-by: Linus Walleij <linus.walleij@ericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. Driver code where pxa_request_dma() is called will most likely
reference DMA registers as well, and it is really unnecessary
to include pxa-regs.h just for this. Move the definitions into
<mach/dma.h> and make relevant drivers include it instead of
<mach/pxa-regs.h>.
2. Introduce DMAC_REGS_VIRT as the virtual address base for these
DMA registers. This allows later processors to re-use the same
IP while registers may start at different I/O address.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Commit 0d3e0460f3
"MMC: CSD and CID timeout values" inadvertently broke
the timeout for the MMC command SEND_EXT_CSD.
This patch puts it back again.
Depending on the characteristics of the controller,
this bug may prevent the use of MMC cards.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
As described here: http://lkml.org/lkml/2009/2/20/265
The CAFE chip is broken due to commit e809517f6f.
Anton added a quirk here: http://lkml.org/lkml/2009/2/20/279 that fixes
CAFE's problem. This adds the quirk for CAFE.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The Samsung SDHCI (and FSL eSDHC) controller block seems to fail
to generate an INT_DATA_END after the transfer has completed and
the bus busy state finished.
Changes in e809517f6f to use the
new busy method are the cause of the behaviour change.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
omap_hsmmc: Change while(); loops with finite version
omap_hsmmc: recover from transfer failures
omap_hsmmc: only MMC1 allows HCTL.SDVS != 1.8V
omap_hsmmc: card detect irq bugfix
sdhci: fix led naming
mmc_test: fix basic read test
s3cmci: Fix hangup in do_pio_write()
Revert "sdhci: force high speed capability on some controllers"
MMC: fix bug - SDHC card capacity not correct
The conversion of atmel-mci to dma_request_channel missed the
initialization of the channel dma_slave information. The filter_fn passed
to dma_request_channel is responsible for initializing the channel's
private data. This implementation has the additional benefit of enabling
a generic client-channel data passing mechanism.
Reviewed-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace the infinite 'while() ;' loops
with a finite loop version.
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Timeouts during a command that has a data phase can result in the next
command issued after the command that failed not being processed, i.e. no
interrupt ever occurs to indicate the command has completed. This failure
can result in a deadlock.
This patch resets the data state machine to clear the error in case of a
command timeout.
Tested on OMAP3430 chip and intensive MMC/SD device removal while
transferring data.
Signed-off-by: Andy Lowe <alowe@mvista.com>
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Based on a patch from Tony Lindgren ... after initialization,
never change HCTL.SDVS except for MMC1. The other controller
instances only support 1.8V in that field, although they can
suport other card/SDIO/eMMC/... voltages with level shifting
solutions such as external transceivers.
MMC2 behavior sanity tested on Overo/WLAN, OMAP3430 SDP, and
custom hardware. MMC1 also sanity tested on those platforms
plus Beagle. This also fixes a bug preventing MMC2 (and also
presumably MMC3) from powering down when requested.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Work around lockdep issue when card detect IRQ handlers run in
thread context ... it forces IRQF_DISABLED, which prevents all
access to twl4030 card detect signals.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Fix the led device naming for the sdhci driver.
The led class documentation defines the led name to have the
form "devicename:colour:function" while not applicable sections
should be left blank.
To comply with the documentation the led device name is changed
from "mmc*" to "mmc*::".
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Due to a typo in the Basic Read test, it's currently identical to the
Basic Write test. Fix this.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
