The driver has been extensively tested in an i.MX6-based system.
AR0521 is a 5.7 mm x 4.3 mm, 5 MPix RGGB MIPI/HiSPi BSI CMOS sensor
from On Semiconductor.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This patch documents DT bindings for the AR0521 camera sensor driver.
[Sakari Ailus: Reworked subject and commit message a little]
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The image format produced by the sensor is controlled by two registers,
whose values computation is open coded in ov5640_set_framefmt().
As we have a list of formats already, move the OV5640_REG_FORMAT_CONTROL00
and OV5640_REG_ISP_FORMAT_MUX_CTRL register values to the static list
of formats instead of open coding it.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The format enumeration list is shared between CSI-2 and DVP modes.
This lead to the enumeration of unsupported format variants in both
modes.
Separate the list of DVP and CSI-2 formats and create helpers to access
the correct one.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The ov5640 driver supports different sizes for different mbus_codes.
In particular:
- 8bpp modes: high resolution sizes (>= 1280x720)
- 16bpp modes: all sizes
- 24bpp modes: low resolutions sizes (< 1280x720)
Adjust the image sizes according to the above constraints.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The ov5640 driver supports different sizes for different mbus_codes.
In particular:
- 8bpp modes: high resolution sizes (>= 1280x720)
- 16bpp modes: all sizes
- 24bpp modes: low resolutions sizes (< 1280x720)
Restrict the frame sizes enumerations to the above constraints.
While at it, make sure the fse->mbus_code parameter is valid, and return
-EINVAL if it's not.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add support for BGR888 image format.
No existing media bus codes describe exactly the way data is transferred
on the CSI-2 bus. This is not a new issue, the CSI-2 YUV422 8-bit format
is described by MEDIA_BUS_FMT_UYVY8_1X16 which is an arbitrary
convention and not an exact match. Use the MEDIA_BUS_FMT_BGR888_1X24 to
follow the same convention, based on the order in which bits are
transmitted over the CSI-2 bus when producing images in RGB24 format.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The driver already supports the 2X8_[LE|BE] variants of RGB565
formats.
As for CSI-2 the 2X8 variants do not apply, add RGB565_1X16 variant
with little-endian ordering of components as required by the CSI-2
specifications.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Parse the device properties and register the rotation and orientation
V4L2 controls using v4l2_ctrl_new_fwnode_properties().
Remove the open-coded parsing of the rotation property and assume the
DTS is correct is providing either <0> or <180> as possible rotations.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Implement the get_selection pad operation for the OV5640 sensor driver.
The supported targets report the sensor's native size, the active pixel
array size and the analog crop rectangle from which the image is
produced.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Implement the init_cfg pad operation to initialize the subdev state
format to the default one.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Now that the frame duration can be controlled by tuning the VBLANK
duration in CSI-2 mode, fix all modes definitions to comply with the
reported FPS.
All modes run at 30 FPS except for full-resolution mode 2592x1944
which runs at 15FPS.
Tested on a 2 data lanes setup in UYVY and RGB565 modes in CSI-2 mode.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The current implementation of ov5640_find_mode() fails if the
frame rate programmed with s_frame_interval doesn't match the
maximum frame rate for the current mode.
This causes issues when moving from one mode with higher FPS to another
one which only supports a lower FPS range with tools like media-ctl.
It also forces users that do not use s_frame_interval(), but rather
configure blankings explicitly, to adjust the programmed FPS range to
avoid failures.
For this reason, remove the FPS check from ov5640_find_mode() and only
perform it at s_frame_interval() time.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Adjust the vertical blanking when s_frame_interval is used.
s_frame_interval allows to set a fixed frame rate, which gets stored as
the sensor's current one. When a new mode is applied, the current frame
rate is reset to the mode's default one. In order to correctly report
the currently configured vertical blanking for s_frame_interval users,
verify that the desired frame rate has not been changed. If that's the
case, compute the correct blanking value and reflect it through the
corresponding v4l2 control.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add the VBLANK control which allows to select the duration of the
frame vertical blankings and allows to control the framerate.
The VBLANK control also modifies the exposure time range, which cannot
exceed the maximum frame length.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add the HBLANK control as read-only.
The hblank value is fixed in the mode definition and is updated
everytime a new format is applied.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The ov5640_mode_init_data is a fictional sensor more which is used to
program the initial sensor settings.
It is only used to initialize the sensor and can be replaced
it with a throw-away mode which just wraps the register table.
Also rename the register table to drop the format from the name to make
it clear an actual sensor mode has to be applied after the initial
programming.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The register tables for all resolutions smaller than 720p are now
identical.
Remove the duplicated ones and create a single ov5640_setting_low_res[]
register table.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Provide a function to shortcut access to the correct timings definition
to avoid repeating the same pattern when accessing the sensor timings.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Separate the timings for the DVP mode from the timings for the CSI-2
mode in the ov5640 modes definition.
The CSI-2 timings will deviate from the DVP ones as the clock tree is
calculated differently.
In CSI-2 mode change the analog crop rectangles as the OV5640 pixel
array is composed as:
- vertically: 16 dummy columns, 2592 valid ones and 16 dummy columns for
a total of 2624 columns
- horizontally: 8 optical black lines, 6 dummy ones, 1944 valid and 6
dummies for a total of 1964 lines
Adjust the analog crop rectangle in CSI-2 mode to:
- Skip the first 16 dummy columns
- Skip the first 14 black/dummy lines
- Pass the whole valid pixel array size to the ISP for all modes except
1024x768, 720p and 1080p which are obtained by cropping the valid pixel
array.
Tested in RGB565, UYVY and RGB888 modes in CSI-2 mode.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Adjust the left crop of 720x480 to enable capture in RGB888 format,
which is otherwise broken.
The 56 pixels alignment has been copied from the 720x576 mode.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The current definition of a sensor mode defines timings as follows:
- hact, vact: Visible width and height
- htot, vtot: Total sizes including blankings
This makes difficult to clearly separate the visible sizes from the
blankings and to make the vertical blanking programmable.
Rework the sensor modes sizes definition to:
- Report the analog crop sizes
- Report the visible crop size
- Report the total pixels per line as HBLANK is fixed
- Report the VBLANK value to make it programmable
Also modify the ov5640_set_timings() function to program all the
windowing registers are remove them from the per-mode register-value
tables.
Do not change the timing values from the ones reported in the register
tables to maintain bisectability.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Re-work the ov5640_set_mipi_pclk() function to calculate the
PLL configuration using the pixel_rate and link_freq values set at
s_fmt time.
Rework the DVP clock mode settings to calculate the pixel clock
internally and remove the assumption on the 16bpp format.
Tested in MIPI CSI-2 mode with 1 and 2 data lanes with:
- all the sensor supported resolutions in UYVY, RGB565 and MJPEG formats.
- resolutions >= 1280x720 in RAW Bayer format.
- resolutions < 1280x720 in RGB888 format.
[Rework pclk_period and link_freq computation]
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
After having set a new format re-calculate the pixel_rate and link_freq
control values and update them when in MIPI mode.
Take into account the limitation of the link frequency having to be
strictly smaller than 1GHz when computing the desired link_freq, and
adjust the resulting pixel_rate acounting for the clock tree
configuration.
[Adjust link_freq calculation]
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add the V4L2_CID_LINK_FREQ control to the ov5640 driver.
Make the control read-only for the moment.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Associate the bit depth to each format supported by the sensor.
The bpp will be used to calculate the line length.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Checking if the sensor is used in DVP or MIPI CSI-2 mode is a repeated
pattern which is about to be repeated more often.
Provide an inline function to shortcut that.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The array of supported modes is close to unreadable.
Re-arrange it giving it some room to breath.
Cosmetic change only.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add to each mode supported by the sensor the ideal pixel rate, as
defined by Table 2.1 in the chip manual.
The ideal pixel rate will be used to compute the MIPI CSI-2 clock tree.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mm-beacon-kit
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add support of 1X16 serial pixel formats in order to support
CSI-2 camera sensor exposing 1x16 pixel formats only.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Expose RGB & YUV 1X16 serial pixel format variants to comply
with CSI-2 camera sensor pixel formats.
Signed-off-by: Hugues Fruchet <hugues.fruchet@foss.st.com>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Those two formats were missing in the list of supported MBUS
formats.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The s_stream callback had several issues:
- If pm_runtime_get_sync() fails, the usage_count is not put.
- The sensor wasn't suspended if s_stream(subdev, 1) failed.
Fix this.
Fixes: ("media: i2c: Add pm_runtime support to ov7251")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The A83T supports MIPI CSI-2 with a composite controller, covering
both the protocol logic and the D-PHY implementation. This controller
seems to be found on the A83T only and probably was abandoned since.
This implementation splits the protocol and D-PHY registers and
uses the PHY framework internally. The D-PHY is not registered as a
standalone PHY driver since it cannot be used with any other
controller.
There are a few notable points about the controller:
- The initialisation sequence involes writing specific magic init
values that do not seem to make any particular sense given the
concerned register fields;
- Interrupts appear to be hitting regardless of the interrupt mask
registers, which can cause a serious flood when transmission errors
occur.
Only 8-bit and 10-bit Bayer formats are currently supported.
While up to 4 internal channels to the CSI controller exist, only one
is currently supported by this implementation.
This work is based on the first version of the driver submitted by
Kévin L'hôpital, which was adapted to mainline from the Allwinner BSP.
This version integrates MIPI CSI-2 support as a standalone V4L2 subdev
instead of merging it in the sun6i-csi driver.
It was tested on a Banana Pi M3 board with an OV8865 sensor in a 4-lane
configuration.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This introduces YAML bindings documentation for the Allwinner A83T
MIPI CSI-2 controller.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add myself as maintainer of the Allwinner A31 MIPI CSI-2 bridge media
driver.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The A31 MIPI CSI-2 controller is a dedicated MIPI CSI-2 bridge
found on Allwinner SoCs such as the A31 and V3/V3s.
It is a standalone block, connected to the CSI controller on one side
and to the MIPI D-PHY block on the other. It has a dedicated address
space, interrupt line and clock.
It is represented as a V4L2 subdev to the CSI controller and takes a
MIPI CSI-2 sensor as its own subdev, all using the fwnode graph and
media controller API.
Only 8-bit and 10-bit Bayer formats are currently supported.
While up to 4 internal channels to the CSI controller exist, only one
is currently supported by this implementation.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This introduces YAML bindings documentation for the Allwinner A31 MIPI
CSI-2 controller.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The A31 CSI controller supports two distinct input interfaces:
parallel and an external MIPI CSI-2 bridge. The parallel interface
is often connected to a set of hardware pins while the MIPI CSI-2
bridge is an internal FIFO-ish link. As a result, these two inputs
are distinguished as two different ports.
Note that only one of the two may be present on a controller instance.
For example, the V3s has one controller dedicated to MIPI-CSI2 and one
dedicated to parallel.
Update the binding with an explicit ports node that holds two distinct
port nodes: one for parallel input and one for MIPI CSI-2.
This is backward-compatible with the single-port approach that was
previously taken for representing the parallel interface port, which
stays enumerated as fwnode port 0.
Note that additional ports may be added in the future, especially to
support feeding the CSI controller's output to the ISP.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The RK3566 and RK3568 SoCs come with a small Hantro instance which is
solely dedicated to encoding. This patch adds the necessary structs to
the Hantro driver to allow the JPEG encoder of it to function.
Through some sleuthing through the vendor's MPP source code and after
closer inspection of the TRM, it was determined that the hardware likely
supports VP8 and H.264 as well.
Tested with the following GStreamer command:
gst-launch-1.0 videotestsrc ! v4l2jpegenc ! matroskamux ! \
filesink location=foo.mkv
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The RK3568 and RK3566 have a Hantro VPU node solely dedicated to
encoding. This patch adds a new binding to describe it, as it
does not really fit the rockchip-vpu binding, since there is no
decoder.
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In reset vpu core, driver will wait for a response event,
but if there are still some events unhandled,
they will be handled first, driver may acquire core lock for that.
So if we do reset in core lock, it may led to reset timeout.
Fixes: 9f599f351e ("media: amphion: add vpu core driver")
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The chroma order of P010 is `CbCr`,
match with the descriptions in `include/uapi/linux/videodev2.h` and the
documentation.
Fixes: 5374d8fb75 ("media: Add P010 video format")
Signed-off-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Replace supportedn with supported\n , i.e. add the missing backslash.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The mdp_ipi_comm structure defines a command that is either
PROCESS (start processing) or DEINIT (destroy instance); we
are using this one to send PROCESS or DEINIT commands from Linux
to an MDP instance through a VPU write but, while the first wants
us to stay 4-bytes aligned, the VPU instead requires an 8-bytes
data alignment.
Keeping in mind that these commands are executed immediately
after sending them (hence not chained with others before the
VPU/MDP "actually" start executing), it is fine to simply add
a padding of 4 bytes to this structure: this keeps the same
performance as before, as we're still stack-allocating it,
while avoiding hackery inside of mtk-vpu to ensure alignment
bringing a definitely bigger performance impact.
Fixes: c8eb2d7e82 ("[media] media: Add Mediatek MDP Driver")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Houlong Wei <houlong.wei@mediatek.com>
Reviewed-by: Irui Wang <irui.wang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
there is an unexpected word 'a' in the comments that need to be dropped
file - drivers/media/usb/pvrusb2/pvrusb2-hdw.c
line - 5044
But now it's a a chicken and egg problem...) */
changed to:
But now it's a chicken and egg problem...) */
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
there is an unexpected word 'a' in the comments that need to be dropped
file - drivers/media/platform/ti/cal/cal-camerarx.c
line - 308
* DRA80xM TRMs have a a slightly simplified sequence.
changed to:
* DRA80xM TRMs have a slightly simplified sequence.
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
