Account for the requirements of the DMA mode currently used.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change ->set_dma_mode method parameters to match ->set_dmamode method
used in struct ata_port_operations.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Change ->set_pio_mode method parameters to match ->set_piomode method
used in struct ata_port_operations.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just use the standard ide_timing_compute() helper to calculate
PIO and MWDMA timings. This fixes some issues with the open-coded
version like allowing faster MWDMA timings than the ones required
by the current PIO mode or not accounting for the enhanced MWDMA
cycle time specified by the device.
Based on libata pata_cmd64x host driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CMD646 corrupts data on concurrent transfers on both channels when IDE SSD is
connected to one of the channels.
Setup that demonstrates this hardware bug: Ultra 5, onboard CMD646, rev 3.
/dev/hda is 8GB Seagate ST38410A in MWDMA2
/dev/hdd is 32GB SSD SiliconHardDisk in MWDMA2
- When reading /dev/hdd (for example with dd or fsck), reads from /dev/hda
are corrupted, there are twiddled single bits 1->0 and some full 32-bit
words corrupted, sometimes commands fail (which switches /dev/hda to
PIO mode but the corruptions happen even in PIO).
- Reads from /dev/hdd don't seem to be corrupted (i.e. fsck passes fine).
- When I connected normal rotating harddisk to /dev/hdd, there was no
corruption, so the corruption is something specific to SSD.
- I tried the same setup on a PCI card with CMD649 and saw no corruption.
This patch serializes the operation for CMD646 and 643 (I didn't test
CMD643 but it may have the same hw bug too because it's earlier design).
CMD649 is good. I don't know anything about CMD 648.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Tested-by: Frans Pop <elendil@planet.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This begins to fix regressions reported by Frans Pop on his Ultra-10.
There are still some funnies left that we are investigating.
Signed-off-by: David S. Miller <davem@davemloft.net>
Change ide_drive_t 'drive_data' field from 'unsigned int' type to 'void *'
type, allowing a wider range of values/types to be stored in this field.
Added 'ide_get_drivedata' and 'ide_set_drivedata' helpers to get and set
the 'drive_data' field.
Fixed all host drivers to maintain coherency with the change in the
'drive_data' field type.
Signed-off-by: Joao Ramos <joao.ramos@inov.pt>
[bart: fix qd65xx build, cast to 'unsigned long', minor Coding Style fixups]
Acked-by: Sergei Shtylyov <sshtylyov@ru.montavista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Convert the driver's two dma_test_irq() methods into test_irq() methods. The
driver will now use the standard dma_test_irq() method implementation which
allows to remove 'cmd54x_dma_ops' and 'cmd648_dma_ops' that become identical
to 'sff_dma_ops'...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Convert the driver's two dma_end() methods into clear_irq() methods -- the
driver will now use the standard dma_end() method implementation, ide_dma_end().
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Set/clear drive->waiting_for_dma flag in the core code
instead of in ->dma_setup and ->dma_end methods.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
All custom ->dma_timeout implementations call the generic one thus it is
possible to have only an optional method for resetting DMA engine instead:
* Add ->dma_clear method and convert hpt366, pdc202xx_old and sl82c105
host drivers to use it.
* Always use ide_dma_timeout() in ide_dma_timeout_retry() and remove
->dma_timeout method.
* Make ide_dma_timeout() static.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Rename dma_timer_expiry() to ide_dma_sff_timer_expiry() and export it.
* Add ->dma_timer_expiry method and use it to set hwif->expiry for
ATA_PROT_DMA protocol in do_rw_taskfile().
* Initialize ->dma_timer_expiry to ide_dma_sff_timer_expiry() for SFF hosts.
* Move setting hwif->expiry from ide_execute_command() to its users and drop
'expiry' argument.
* Use ide_execute_command() instead of ->dma_exec_cmd in do_rw_taskfile().
* Remove ->dma_exec_cmd method and its implementations.
* Unexport ide_execute_command() and ide_dma_intr().
v2:
* Fix CONFIG_BLK_DEV_IDEDMA=n build (noticed by Randy Dunlap).
* Fix *dma_expiry naming (suggested by Sergei Shtylyov).
There should be no functional changes caused by this patch.
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Return 0 instead of dev->irq in ->init_chipset implementations.
* Fix ->init_chipset method to return 'int' value instead of
'unsigned int' one.
This fixes ->init_chipset handling for host drivers (cs5530, hpt366
and pdc202xx_new) for which it is possible for this method to fail.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move apparently misplaced read_sff_dma_status() method from 'struct ide_tp_ops'
to 'struct ide_dma_ops', renaming it to dma_sff_read_status() and making only
required for SFF-8038i compatible IDE controller drivers (greatly cutting down
the number of initializers) as its only user (outside ide-dma-sff.c and such
drivers) appears to be ide_pci_check_simplex() which is only called for such
controllers...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Set IDE_HFLAG_SERIALIZE explictly for CMD646.
* Remove no longer needed ide_cmd646 chipset type (which has
a nice side-effect of fixing handling of unexpected IRQs).
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
