handle_reply() calls complete_request() only if the first OSD reply
has ONDISK flag.
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Reviewed-by: Sage Weil <sage@inktank.com>
If an osd client response message arrives that has a front section
that's too big for the buffer set aside to receive it, a warning
gets reported and a new buffer is allocated.
The warning says nothing about which connection had the problem.
Add the peer type and number to what gets reported, to be a bit more
informative.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
When an osd request is set to linger, the osd client holds onto the
request so it can be re-submitted following certain osd map changes.
The osd client holds a reference to the request until it is
unregistered. This is used by rbd for watch requests.
Currently, the reference is taken when the request is marked with
the linger flag. This means that if an error occurs after that
time but before the the request completes successfully, that
reference is leaked.
There's really no reason to take the reference until the request is
registered in the the osd client's list of lingering requests, and
that only happens when the lingering (watch) request completes
successfully.
So take that reference only when it gets registered following
succesful completion, and drop it (as before) when the request
gets unregistered. This avoids the reference problem on error
in rbd.
Rearrange ceph_osdc_unregister_linger_request() to avoid using
the request pointer after it may have been freed.
And hold an extra reference in kick_requests() while handling
a linger request that has not yet been registered, to ensure
it doesn't go away.
This resolves:
http://tracker.ceph.com/issues/3859
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
An osd client has a red-black tree describing its osds, and
occasionally we would get crashes due to one of these trees tree
becoming corrupt somehow.
The problem turned out to be that reset_changed_osds() was being
called without protection of the osd client request mutex. That
function would call __reset_osd() for any osd that had changed, and
__reset_osd() would call __remove_osd() for any osd with no
outstanding requests, and finally __remove_osd() would remove the
corresponding entry from the red-black tree. Thus, the tree was
getting modified without having any lock protection, and was
vulnerable to problems due to concurrent updates.
This appears to be the only osd tree updating path that has this
problem. It can be fairly easily fixed by moving the call up
a few lines, to just before the request mutex gets dropped
in kick_requests().
This resolves:
http://tracker.ceph.com/issues/5043
Cc: stable@vger.kernel.org # 3.4+
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
The rbd code has a need to be able to restart an osd request that
has already been started and completed once before. This currently
wouldn't work right because the osd client code assumes an osd
request will be started exactly once Certain fields in a request
are never cleared and this leads to trouble if you try to reuse it.
Specifically, the r_sent, r_got_reply, and r_completed fields are
never cleared. The r_sent field records the osd incarnation at the
time the request was sent to that osd. If that's non-zero, the
message won't get re-mapped to a target osd properly, and won't be
put on the unsafe requests list the first time it's sent as it
should. The r_got_reply field is used in handle_reply() to ensure
the reply to a request is processed only once. And the r_completed
field is used for lingering requests to avoid calling the callback
function every time the osd client re-sends the request on behalf of
its initiator.
Each osd request passes through ceph_osdc_start_request() when
responsibility for the request is handed over to the osd client for
completion. We can safely zero these three fields there each time a
request gets started.
One last related change--clear the r_linger flag when a request
is no longer registered as a linger request.
This resolves:
http://tracker.ceph.com/issues/5026
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Create a slab cache to manage allocation of ceph_osdc_request
structures.
This resolves:
http://tracker.ceph.com/issues/3926
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
A WATCH op includes an object version. The version that's supplied
is incorrectly byte-swapped osd_req_op_watch_init() where it's first
assigned (it's been this way since that code was first added).
The result is that the version sent to the osd is wrong, because
that value gets byte-swapped again in osd_req_encode_op(). This
is the source of a sparse warning related to improper byte order in
the assignment.
The approach of using the version to avoid a race is deprecated
(see http://tracker.ceph.com/issues/3871), and the watch parameter
is no longer even examined by the osd. So fix the assignment in
osd_req_op_watch_init() so it no longer does the byte swap.
This resolves:
http://tracker.ceph.com/issues/3847
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Add the ability to provide an array of pages as outbound request
data for object class method calls.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Allow osd request ops that aren't otherwise structured (not class,
extent, or watch ops) to specify "raw" data to be used to hold
incoming data for the op. Make use of this capability for the osd
STAT op.
Prefix the name of the private function osd_req_op_init() with "_",
and expose a new function by that (earlier) name whose purpose is to
initialize osd ops with (only) implied data.
For now we'll just support the use of a page array for an osd op
with incoming raw data.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
There are a bunch of functions defined to encapsulate getting the
address of a data field for a particular op in an osd request.
They're all defined the same way, so create a macro to take the
place of all of them.
Two of these are used outside the osd client code, so preserve them
(but convert them to use the new macro internally). Stop exporting
the ones that aren't used elsewhere.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
In the incremental move toward supporting distinct data items in an
osd request some of the functions had "write_request" parameters to
indicate, basically, whether the data belonged to in_data or the
out_data. Now that we maintain the data fields in the op structure
there is no need to indicate the direction, so get rid of the
"write_request" parameters.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
An osd request currently has two callbacks. They inform the
initiator of the request when we've received confirmation for the
target osd that a request was received, and when the osd indicates
all changes described by the request are durable.
The only time the second callback is used is in the ceph file system
for a synchronous write. There's a race that makes some handling of
this case unsafe. This patch addresses this problem. The error
handling for this callback is also kind of gross, and this patch
changes that as well.
In ceph_sync_write(), if a safe callback is requested we want to add
the request on the ceph inode's unsafe items list. Because items on
this list must have their tid set (by ceph_osd_start_request()), the
request added *after* the call to that function returns. The
problem with this is that there's a race between starting the
request and adding it to the unsafe items list; the request may
already be complete before ceph_sync_write() even begins to put it
on the list.
To address this, we change the way the "safe" callback is used.
Rather than just calling it when the request is "safe", we use it to
notify the initiator the bounds (start and end) of the period during
which the request is *unsafe*. So the initiator gets notified just
before the request gets sent to the osd (when it is "unsafe"), and
again when it's known the results are durable (it's no longer
unsafe). The first call will get made in __send_request(), just
before the request message gets sent to the messenger for the first
time. That function is only called by __send_queued(), which is
always called with the osd client's request mutex held.
We then have this callback function insert the request on the ceph
inode's unsafe list when we're told the request is unsafe. This
will avoid the race because this call will be made under protection
of the osd client's request mutex. It also nicely groups the setup
and cleanup of the state associated with managing unsafe requests.
The name of the "safe" callback field is changed to "unsafe" to
better reflect its new purpose. It has a Boolean "unsafe" parameter
to indicate whether the request is becoming unsafe or is now safe.
Because the "msg" parameter wasn't used, we drop that.
This resolves the original problem reportedin:
http://tracker.ceph.com/issues/4706
Reported-by: Yan, Zheng <zheng.z.yan@intel.com>
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Yan, Zheng <zheng.z.yan@intel.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Right now the data for a method call is specified via a pointer and
length, and it's copied--along with the class and method name--into
a pagelist data item to be sent to the osd. Instead, encode the
data in a data item separate from the class and method names.
This will allow large amounts of data to be supplied to methods
without copying. Only rbd uses the class functionality right now,
and when it really needs this it will probably need to use a page
array rather than a page list. But this simple implementation
demonstrates the functionality on the osd client, and that's enough
for now.
This resolves:
http://tracker.ceph.com/issues/4104
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Change the names of the functions that put data on a pagelist to
reflect that we're adding to whatever's already there rather than
just setting it to the one thing. Currently only one data item is
ever added to a message, but that's about to change.
This resolves:
http://tracker.ceph.com/issues/2770
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Finally! Convert the osd op data pointers into real structures, and
make the switch over to using them instead of having all ops share
the in and/or out data structures in the osd request.
Set up a new function to traverse the set of ops and release any
data associated with them (pages).
This and the patches leading up to it resolve:
http://tracker.ceph.com/issues/4657
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Still using the osd request r_data_in and r_data_out pointer, but
we're basically only referring to it via the data pointers in the
osd ops. And we're transferring that information to the request
or reply message only when the op indicates it's needed, in
osd_req_encode_op().
To avoid a forward reference, ceph_osdc_msg_data_set() was moved up
in the file.
Don't bother calling ceph_osd_data_init(), in ceph_osd_alloc(),
because the ops array will already be zeroed anyway.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
This ends up being a rather large patch but what it's doing is
somewhat straightforward.
Basically, this is replacing two calls with one. The first of the
two calls is initializing a struct ceph_osd_data with data (either a
page array, a page list, or a bio list); the second is setting an
osd request op so it associates that data with one of the op's
parameters. In place of those two will be a single function that
initializes the op directly.
That means we sort of fan out a set of the needed functions:
- extent ops with pages data
- extent ops with pagelist data
- extent ops with bio list data
and
- class ops with page data for receiving a response
We also have define another one, but it's only used internally:
- class ops with pagelist data for request parameters
Note that we *still* haven't gotten rid of the osd request's
r_data_in and r_data_out fields. All the osd ops refer to them for
their data. For now, these data fields are pointers assigned to the
appropriate r_data_* field when these new functions are called.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
All calls of ceph_osdc_start_request() are preceded (in the case of
rbd, almost) immediately by a call to ceph_osdc_build_request().
Move the build calls at the top of ceph_osdc_start_request() out of
there and into the ceph_osdc_build_request(). Nothing prevents
moving these calls to the top of ceph_osdc_build_request(), either
(and we're going to want them there in the next patch) so put them
at the top.
This and the next patch are related to:
http://tracker.ceph.com/issues/4657
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
This simply moves ceph_osdc_build_request() later in its source
file without any change. Done as a separate patch to facilitate
review of the change in the next patch.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
An object class method is formatted using a pagelist which contains
the class name, the method name, and the data concatenated into an
osd request's outbound data.
Currently when a class op is initialized in osd_req_op_cls_init(),
the lengths of and pointers to these three items are recorded.
Later, when the op is getting formatted into the request message, a
new pagelist is created and that is when these items get copied into
the pagelist.
This patch makes it so the pagelist to hold these items is created
when the op is initialized instead.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
An osd request now holds all of its source op structures, and every
place that initializes one of these is in fact initializing one
of the entries in the the osd request's array.
So rather than supplying the address of the op to initialize, have
caller specify the osd request and an indication of which op it
would like to initialize. This better hides the details the
op structure (and faciltates moving the data pointers they use).
Since osd_req_op_init() is a common routine, and it's not used
outside the osd client code, give it static scope. Also make
it return the address of the specified op (so all the other
init routines don't have to repeat that code).
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
An extent type osd operation currently implies that there will
be corresponding data supplied in the data portion of the request
(for write) or response (for read) message. Similarly, an osd class
method operation implies a data item will be supplied to receive
the response data from the operation.
Add a ceph_osd_data pointer to each of those structures, and assign
it to point to eithre the incoming or the outgoing data structure in
the osd message. The data is not always available when an op is
initially set up, so add two new functions to allow setting them
after the op has been initialized.
Begin to make use of the data item pointer available in the osd
operation rather than the request data in or out structure in
places where it's convenient. Add some assertions to verify
pointers are always set the way they're expected to be.
This is a sort of stepping stone toward really moving the data
into the osd request ops, to allow for some validation before
making that jump.
This is the first in a series of patches that resolve:
http://tracker.ceph.com/issues/4657
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
There are fields "indata" and "indata_len" defined the ceph osd
request op structure. The "in" part is with from the point of view
of the osd server, but is a little confusing here on the client
side. Change their names to use "request" instead of "in" to
indicate that it defines data provided with the request (as opposed
the data returned in the response).
Rename the local variable in osd_req_encode_op() to match.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
An osd request keeps a pointer to the osd operations (ops) array
that it builds in its request message.
In order to allow each op in the array to have its own distinct
data, we will need to keep track of each op's data, and that
information does not go over the wire.
As long as we're tracking the data we might as well just track the
entire (source) op definition for each of the ops. And if we're
doing that, we'll have no more need to keep a pointer to the
wire-encoded version.
This patch makes the array of source ops be kept with the osd
request structure, and uses that instead of the version encoded in
the message in places where that was previously used. The array
will be embedded in the request structure, and the maximum number of
ops we ever actually use is currently 2. So reduce CEPH_OSD_MAX_OP
to 2 to reduce the size of the structure.
The result of doing this sort of ripples back up, and as a result
various function parameters and local variables become unnecessary.
Make r_num_ops be unsigned, and move the definition of struct
ceph_osd_req_op earlier to ensure it's defined where needed.
It does not yet add per-op data, that's coming soon.
This resolves:
http://tracker.ceph.com/issues/4656
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
One more osd data helper, which returns the length of the
data item, regardless of its type.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Define ceph_osd_data_init() and ceph_osd_data_release() to clean up
a little code.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Define and use functions that encapsulate the initializion of a
ceph_osd_data structure.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
This is a simple change, extracting the number of incoming data
bytes just once in handle_reply().
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Hold off building the osd request message in ceph_writepages_start()
until just before it will be submitted to the osd client for
execution.
We'll still create the request and allocate the page pointer array
after we learn we have at least one page to write. A local variable
will be used to keep track of the allocated array of pages. Wait
until just before submitting the request for assigning that page
array pointer to the request message.
Create ands use a new function osd_req_op_extent_update() whose
purpose is to serve this one spot where the length value supplied
when an osd request's op was initially formatted might need to get
changed (reduced, never increased) before submitting the request.
Previously, ceph_writepages_start() assigned the message header's
data length because of this update. That's no longer necessary,
because ceph_osdc_build_request() will recalculate the right
value to use based on the content of the ops in the request.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Defer building the osd request until just before submitting it in
all callers except ceph_writepages_start(). (That caller will be
handed in the next patch.)
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
This patch moves the call to ceph_osdc_build_request() out of
ceph_osdc_new_request() and into its caller.
This is in order to defer formatting osd operation information into
the request message until just before request is started.
The only unusual (ab)user of ceph_osdc_build_request() is
ceph_writepages_start(), where the final length of write request may
change (downward) based on the current inode size or the oldest
snapshot context with dirty data for the inode.
The remaining callers don't change anything in the request after has
been built.
This means the ops array is now supplied by the caller. It also
means there is no need to pass the mtime to ceph_osdc_new_request()
(it gets provided to ceph_osdc_build_request()). And rather than
passing a do_sync flag, have the number of ops in the ops array
supplied imply adding a second STARTSYNC operation after the READ or
WRITE requested.
This and some of the patches that follow are related to having the
messenger (only) be responsible for filling the content of the
message header, as described here:
http://tracker.ceph.com/issues/4589
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Keep track of the length of the data portion for a message in a
separate field in the ceph_msg structure. This information has
been maintained in wire byte order in the message header, but
that's going to change soon.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
A field in an osd request keeps track of whether a connection is
currently filling the request's reply message. This patch gets rid
of that field.
An osd request includes two messages--a request and a reply--and
they're both associated with the connection that existed to its
the target osd at the time the request was created.
An osd request can be dropped early, even when it's in flight.
And at that time both messages are released. It's possible the
reply message has been supplied to its connection to receive
an incoming response message at the time the osd request gets
dropped. So ceph_osdc_release_request() revokes that message
from the connection before releasing it so things get cleaned up
properly.
Previously this may have caused a problem, because the connection
that a message was associated with might have gone away before the
revoke request. And to avoid any problems using that connection,
the osd client held a reference to it when it supplies its response
message.
However since this commit:
38941f80 libceph: have messages point to their connection
all messages hold a reference to the connection they are associated
with whenever the connection is actively operating on the message
(i.e. while the message is queued to send or sending, and when it
data is being received into it). And if a message has no connection
associated with it, ceph_msg_revoke_incoming() won't do anything
when asked to revoke it.
As a result, there is no need to keep an additional reference to the
connection associated with a message when we hand the message to the
messenger when it calls our alloc_msg() method to receive something.
If the connection *were* operating on it, it would have its own
reference, and if not, there's no work to be done when we need to
revoke it.
So get rid of the osd request's r_con_filling_msg field.
This resolves:
http://tracker.ceph.com/issues/4647
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
There are two basically identical definitions of __decode_pgid()
in libceph, one in "net/ceph/osdmap.c" and the other in
"net/ceph/osd_client.c". Get rid of both, and instead define
a single inline version in "include/linux/ceph/osdmap.h".
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The osd client mutex is acquired just before getting a reference to
a request in handle_reply(). However the error paths after that
don't drop the mutex before returning as they should.
Drop the mutex after dropping the request reference. Also add a
bad_mutex label at that point and use it so the failed request
lookup case can be handled with the rest.
This resolves:
http://tracker.ceph.com/issues/4615
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Use osd_req_op_extent_init() in ceph_osdc_new_request() to
initialize the one or two ops built in that function.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
All callers of ceph_osd_new_request() pass either CEPH_OSD_OP_READ
or CEPH_OSD_OP_WRITE as the opcode value. The function assumes it
by filling in the extent fields in the ops array it builds. So just
assert that is the case, and don't bother calling op_has_extent()
before filling in the first osd operation in the array.
Define some local variables to gather the information to fill into
the first op, and then fill in the op array all in one place.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The ceph_osdc_new_request() an array of osd operations is built up
and filled in partially within that function and partially in the
called function calc_layout(). Move the latter part back out to
ceph_osdc_new_request() so it's all done in one place. This makes
it unnecessary to pass the op pointer to calc_layout(), so get rid
of that parameter.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The purpose of calc_layout() is to determine, given a file offset
and length and a layout describing the placement of file data across
objects, where in "object space" that data resides.
Specifically, it determines which object should hold the first part
of the specified range of file data, and the offset and length of
data within that object. The length will not exceed the bounds
of the object, and the caller is informed of that maximum length.
Add two parameters to calc_layout() to allow the object-relative
offset and length to be passed back to the caller.
This is the first steps toward having ceph_osdc_new_request() build
its osd op structure using osd_req_op_extent_init().
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The rbd code has a function that allocates and populates a
ceph_osd_req_op structure (the in-core version of an osd request
operation). When reviewed, Josh suggested two things: that the
big varargs function might be better split into type-specific
functions; and that this functionality really belongs in the osd
client rather than rbd.
This patch implements both of Josh's suggestions. It breaks
up the rbd function into separate functions and defines them
in the osd client module as exported interfaces. Unlike the
rbd version, however, the functions don't allocate an osd_req_op
structure; they are provided the address of one and that is
initialized instead.
The rbd function has been eliminated and calls to it have been
replaced by calls to the new routines. The rbd code now now use a
stack (struct) variable to hold the op rather than allocating and
freeing it each time.
For now only the capabilities used by rbd are implemented.
Implementing all the other osd op types, and making the rest of the
code use it will be done separately, in the next few patches.
Note that only the extent, cls, and watch portions of the
ceph_osd_req_op structure are currently used. Delete the others
(xattr, pgls, and snap) from its definition so nobody thinks it's
actually implemented or needed. We can add it back again later
if needed, when we know it's been tested.
This (and a few follow-on patches) resolves:
http://tracker.ceph.com/issues/3861
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Define a separate function to determine the validity of an opcode,
and use it inside osd_req_encode_op() in order to unclutter that
function.
Don't update the destination op at all--and return zero--if an
unsupported or unrecognized opcode is seen in osd_req_encode_op().
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
In ceph_osdc_build_request() there is a call to cpu_to_le16() which
provides a 64-bit value as its argument. Because of the implied
byte swapping going on it looked pretty suspect to me.
At the moment it turns out the behavior is well defined, but masking
off those bottom bits explicitly eliminates this distraction, and is
in fact more directly related to the purpose of the message header's
data_off field.
This resolves:
http://tracker.ceph.com/issues/4125
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
An osd expects the transaction ids of arriving request messages from
a given client to a given osd to increase monotonically. So the osd
client needs to send its requests in ascending tid order.
The transaction id for a request is set at the time it is
registered, in __register_request(). This is also where the request
gets placed at the end of the osd client's unsent messages list.
At the end of ceph_osdc_start_request(), the request message for a
newly-mapped osd request is supplied to the messenger to be sent
(via __send_request()). If any other messages were present in the
osd client's unsent list at that point they would be sent *after*
this new request message.
Because those unsent messages have already been registered, their
tids would be lower than the newly-mapped request message, and
sending that message first can violate the tid ordering rule.
Rather than sending the new request only, send all queued requests
(including the new one) at that point in ceph_osdc_start_request().
This ensures the tid ordering property is preserved.
With this in place, all messages should now be sent in tid order
regardless of whether they're being sent for the first time or
re-sent as a result of a call to osd_reset().
This resolves:
http://tracker.ceph.com/issues/4392
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-off-by: Sage Weil <sage@inktank.com>
In __map_request(), when adding a request to an osd client's unsent
list, add it to the tail rather than the head. That way the newest
entries (with the highest tid value) will be last.
Maintain an osd's request list in order of increasing tid also.
Finally--to be consistent--maintain an osd client's "notarget" list
in that order as well.
This partially resolves:
http://tracker.ceph.com/issues/4392
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-off-by: Sage Weil <sage@inktank.com>
The osd expects incoming requests for a given object from a given
client to arrive in order, with the tid for each request being
greater than the tid for requests that have already arrived. This
patch fixes two places the osd client might not maintain that
ordering.
For the osd client, the connection fault method is osd_reset().
That function calls __reset_osd() to close and re-open the
connection, then calls __kick_osd_requests() to cause all
outstanding requests for the affected osd to be re-sent after
the connection has been re-established.
When an osd is reset, any in-flight messages will need to be
re-sent. An osd client maintains distinct lists for unsent and
in-flight messages. Meanwhile, an osd maintains a single list of
all its requests (both sent and un-sent). (Each message is linked
into two lists--one for the osd client and one list for the osd.)
To process an osd "kick" operation, the request list for the *osd*
is traversed, and each request is moved off whichever osd *client*
list it was on (unsent or sent) and placed onto the osd client's
unsent list. (It remains where it is on the osd's request list.)
When that is done, osd_reset() calls __send_queued() to cause each
of the osd client's unsent messages to be sent.
OK, with that background...
As the osd request list is traversed each request is prepended to
the osd client's unsent list in the order they're seen. The effect
of this is to reverse the order of these requests as they are put
(back) onto the unsent list.
Instead, build up a list of only the requests for an osd that have
already been sent (by checking their r_sent flag values). Once an
unsent request is found, stop examining requests and prepend the
requests that need re-sending to the osd client's unsent list.
Preserve the original order of requests in the process (previously
re-queued requests were reversed in this process). Because they
have already been sent, they will have lower tids than any request
already present on the unsent list.
Just below that, traverse the linger list in forward order as
before, but add them to the *tail* of the list rather than the head.
These requests get re-registered, and in the process are give a new
(higher) tid, so the should go at the end.
This partially resolves:
http://tracker.ceph.com/issues/4392
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-off-by: Sage Weil <sage@inktank.com>
Since we no longer drop the request mutex between registering and
mapping an osd request in ceph_osdc_start_request(), there is no
chance of a race with kick_requests().
We can now therefore map and send the new request unconditionally
(but we'll issue a warning should it ever occur).
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-off-by: Sage Weil <sage@inktank.com>
One of the first things ceph_osdc_start_request() does is register
the request. It then acquires the osd client's map semaphore and
request mutex and proceeds to map and send the request.
There is no reason the request has to be registered before acquiring
the map semaphore. So hold off doing so until after the map
semaphore is held.
Since register_request() is nothing more than a wrapper around
__register_request(), call the latter function instead, after
acquiring the request mutex.
That leaves register_request() unused, so get rid of it.
This partially resolves:
http://tracker.ceph.com/issues/4392
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-off-by: Sage Weil <sage@inktank.com>
Use wrapper functions that check whether the auth op exists so that callers
do not need a bunch of conditional checks. Simplifies the external
interface.
Signed-off-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@inktank.com>
Currently the messenger calls out to a get_authorizer con op, which will
create a new authorizer if it doesn't yet have one. In the meantime, when
we rotate our service keys, the authorizer doesn't get updated. Eventually
it will be rejected by the server on a new connection attempt and get
invalidated, and we will then rebuild a new authorizer, but this is not
ideal.
Instead, if we do have an authorizer, call a new update_authorizer op that
will verify that the current authorizer is using the latest secret. If it
is not, we will build a new one that does. This avoids the transient
failure.
This fixes one of the sorry sequence of events for bug
http://tracker.ceph.com/issues/4282
Signed-off-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@inktank.com>
The osd trail is a pagelist, used only for a CALL osd operation
to hold the class and method names, along with any input data for
the call.
It is only currently used by the rbd client, and when it's used it
is the only bit of outbound data in the osd request. Since we
already support (non-trail) pagelist data in a message, we can
just save this outbound CALL data in the "normal" pagelist rather
than the trail, and get rid of the trail entirely.
The existing pagelist support depends on the pagelist being
dynamically allocated, and ownership of it is passed to the
messenger once it's been attached to a message. (That is to say,
the messenger releases and frees the pagelist when it's done with
it). That means we need to dynamically allocate the pagelist also.
Note that we simply assert that the allocation of a pagelist
structure succeeds. Appending to a pagelist might require a dynamic
allocation, so we're already assuming we won't run into trouble
doing so (we're just ignore any failures--and that should be fixed
at some point).
This resolves:
http://tracker.ceph.com/issues/4407
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Add support for recording a ceph pagelist as data associated with an
osd request.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The length of outgoing data in an osd request is dependent on the
osd ops that are embedded in that request. Each op is encoded into
a request message using osd_req_encode_op(), so that should be used
to determine the amount of outgoing data implied by the op as it
is encoded.
Have osd_req_encode_op() return the number of bytes of outgoing data
implied by the op being encoded, and accumulate and use that in
ceph_osdc_build_request().
As a result, ceph_osdc_build_request() no longer requires its "len"
parameter, so get rid of it.
Using the sum of the op lengths rather than the length provided is
a valid change because:
- The only callers of osd ceph_osdc_build_request() are
rbd and the osd client (in ceph_osdc_new_request() on
behalf of the file system).
- When rbd calls it, the length provided is only non-zero for
write requests, and in that case the single op has the
same length value as what was passed here.
- When called from ceph_osdc_new_request(), (it's not all that
easy to see, but) the length passed is also always the same
as the extent length encoded in its (single) write op if
present.
This resolves:
http://tracker.ceph.com/issues/4406
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
When an incoming message is destined for the osd client, the
messenger calls the osd client's alloc_msg method. That function
looks up which request has the tid matching the incoming message,
and returns the request message that was preallocated to receive the
response. The response message is therefore known before the
request is even started.
Between the start of the request and the receipt of the response,
the request and its data fields will not change, so there's no
reason we need to hold off setting them. In fact it's preferable
to set them just once because it's more obvious that they're
unchanging.
So set up the fields describing where incoming data is to land in a
response message at the beginning of ceph_osdc_start_request().
Define a helper function that sets these fields, and use it to
set the fields for both outgoing data in the request message and
incoming data in the response.
This resolves:
http://tracker.ceph.com/issues/4284
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Change it so we only assign outgoing data information for messages
if there is outgoing data to send.
This then allows us to add a few more (currently commented-out)
assertions.
This is related to:
http://tracker.ceph.com/issues/4284
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Greg Farnum <greg@inktank.com>
Define ceph_msg_data_set_pagelist(), ceph_msg_data_set_bio(), and
ceph_msg_data_set_trail() to clearly abstract the assignment of the
remaining data-related fields in a ceph message structure. Use the
new functions in the osd client and mds client.
This partially resolves:
http://tracker.ceph.com/issues/4263
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
When setting page array information for message data, provide the
byte length rather than the page count ceph_msg_data_set_pages().
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Define a function ceph_msg_data_set_pages(), which more clearly
abstracts the assignment page-related fields for data in a ceph
message structure. Use this new function in the osd client and mds
client.
Ideally, these fields would never be set more than once (with
BUG_ON() calls to guarantee that). At the moment though the osd
client sets these every time it receives a message, and in the event
of a communication problem this can happen more than once. (This
will be resolved shortly, but setting up these helpers first makes
it all a bit easier to work with.)
Rearrange the field order in a ceph_msg structure to group those
that are used to define the possible data payloads.
This partially resolves:
http://tracker.ceph.com/issues/4263
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Record the byte count for an osd request rather than the page count.
The number of pages can always be derived from the byte count (and
alignment/offset) but the reverse is not true.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
An osd request defines information about where data to be read
should be placed as well as where data to write comes from.
Currently these are represented by common fields.
Keep information about data for writing separate from data to be
read by splitting these into data_in and data_out fields.
This is the key patch in this whole series, in that it actually
identifies which osd requests generate outgoing data and which
generate incoming data. It's less obvious (currently) that an osd
CALL op generates both outgoing and incoming data; that's the focus
of some upcoming work.
This resolves:
http://tracker.ceph.com/issues/4127
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
An osd request uses either pages or a bio list for its data. Use a
union to record information about the two, and add a data type
tag to select between them.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Pull the fields in an osd request structure that define the data for
the request out into a separate structure.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Currently ceph_osdc_new_request() assigns an osd request's
r_num_pages and r_alignment fields. The only thing it does
after that is call ceph_osdc_build_request(), and that doesn't
need those fields to be assigned.
Move the assignment of those fields out of ceph_osdc_new_request()
and into its caller. As a result, the page_align parameter is no
longer used, so get rid of it.
Note that in ceph_sync_write(), the value for req->r_num_pages had
already been calculated earlier (as num_pages, and fortunately
it was computed the same way). So don't bother recomputing it,
but because it's not needed earlier, move that calculation after the
call to ceph_osdc_new_request(). Hold off making the assignment to
r_alignment, doing it instead r_pages and r_num_pages are
getting set.
Similarly, in start_read(), nr_pages already holds the number of
pages in the array (and is calculated the same way), so there's no
need to recompute it. Move the assignment of the page alignment
down with the others there as well.
This and the next few patches are preparation work for:
http://tracker.ceph.com/issues/4127
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The purpose of ceph_calc_object_layout() is to fill in the pool
number and seed for a ceph_pg structure provided, based on a given
osd map and target object id.
Currently that function takes a file layout parameter, but the only
thing used out of that is its pool number.
Change the function so it takes a pool number rather than the full
file layout structure. Only update the ceph_pg if the pool is found
in the osd map. Get rid of few useless lines of code from the
function while there.
Since the function now very clearly just fills in the ceph_pg
structure it's provided, rename it ceph_calc_ceph_pg().
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The new cases added to osd_req_encode_op() caused a new sparse
error, which highlighted an existing problem that had been
overlooked since it was originally checked in. When an unsupported
opcode is found the destination rather than the source opcode was
being used in the error message. The two differ in their byte
order, and we want to be using the one in the source.
Fix the problem in both spots.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
An osd request marked to linger will be re-submitted in the event
a connection to the target osd gets dropped. Currently, if there
is a callback function associated with a request it will be called
each time a request is submitted--which for lingering requests can
be more than once.
Change it so a request--including lingering ones--will get completed
(from the perspective of the user of the osd client) exactly once.
This resolves:
http://tracker.ceph.com/issues/3967
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The page alignment field for a request is currently set in
ceph_osdc_build_request(). It's not needed at that point
nor do either of its callers need that value assigned at
any point before they call ceph_osdc_start_request().
So move that assignment into ceph_osdc_start_request().
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Use distinct fields for tracking the number of pages in a message's
page array and in a message's page list. Currently only one or the
other is used at a time, but that will be changing soon.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The only remaining reason to pass the osd request to calc_layout()
is to fill in its r_num_pages and r_page_alignment fields. Once it
fills those in, it doesn't do anything more with them.
We can therefore move those assignments into the caller, and get rid
of the "req" parameter entirely.
Note, however, that the only caller is ceph_osdc_new_request(),
and that immediately overwrites those fields with values based on
its passed-in page offset. So the assignment inside calc_layout()
was redundant anyway.
This resolves:
http://tracker.ceph.com/issues/4262
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Move the formatting of the object name (oid) to use for an object
request into the caller of calc_layout(). This makes the "vino"
parameter no longer necessary, so get rid of it.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Have calc_layout() pass the computed object number back to its
caller. (This is a small step to simplify review.)
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
If an invalid layout is provided to ceph_osdc_new_request(), its
call to calc_layout() might return an error. At that point in the
function we've already allocated an osd request structure, so we
need to free it (drop a reference) in the event such an error
occurs.
The only other value calc_layout() will return is 0, so make that
explicit in the successful case.
This resolves:
http://tracker.ceph.com/issues/4240
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Use the new version of the encoding for osd requests and replies. In the
process, update the way we are tracking request ops and reply lengths and
results in the struct ceph_osd_request. Update the rbd and fs/ceph users
appropriately.
The main changes are:
- we keep pointers into the request memory for fields we need to update
each time the request is sent out over the wire
- we keep information about the result in an array in the request struct
where the users can easily get at it.
Signed-off-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@inktank.com>
Instead of using the old ceph_object_layout struct, update our internal
ceph_calc_object_layout method to use the ceph_pg type. This allows us to
pass the full 32-bit precision of the pgid.seed to the callers. It also
allows some callers to avoid reaching into the request structures for the
struct ceph_object_layout fields.
Signed-off-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@inktank.com>
Always decode data into our cpu-native ceph_pg type that has the correct
field widths. Limit any remaining uses of ceph_pg_v1 to dealing with the
legacy protocol.
Signed-off-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@inktank.com>
Rename the old version this type to distinguish it from the new version.
Signed-off-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@inktank.com>
Add support for CEPH_OSD_OP_STAT operations in the osd client
and in rbd.
This operation sends no data to the osd; everything required is
encoded in identity of the target object.
The result will be ENOENT if the object doesn't exist. If it does
exist and no other error occurs the server returns the size and last
modification time of the target object as output data (in little
endian format). The size is a 64 bit unsigned and the time is
ceph_timespec structure (two unsigned 32-bit integers, representing
a seconds and nanoseconds value).
This resolves:
http://tracker.ceph.com/issues/4007
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Simplify the way the data length recorded in a message header is
calculated in ceph_osdc_build_request().
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
In osd_req_encode_op() there are a few cases that handle osd
opcodes that are never used in the kernel. The presence of
this code gives the impression it's correct (which really can't
be assumed), and may impose some unnecessary restrictions on
some upcoming refactoring of this code.
So delete this effectively dead code, and report uses of the
previously handled cases as unsupported.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
If osd_req_encode_op() is given any opcode it doesn't recognize
it reports an error.
This patch fleshes out that routine to distinguish between
well-defined but unsupported values and values that are simply
bogus.
This and the next commit are related to:
http://tracker.ceph.com/issues/4126
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
There are no actual users of ceph_osdc_wait_event(). This would
have been one-shot events, but we no longer support those so just
get rid of this function.
Since this leaves nothing else that waits for the completion of an
event, we can get rid of the completion in a struct ceph_osd_event.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
There is only one caller of ceph_osdc_create_event(), and it
provides 0 as its "one_shot" argument. Get rid of that argument and
just use 0 in its place.
Replace the code in handle_watch_notify() that executes if one_shot
is nonzero in the event with a BUG_ON() call.
While modifying "osd_client.c", give handle_watch_notify() static
scope.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
There is no caller of ceph_calc_raw_layout() outside of libceph, so
there's no need to export from the module.
Furthermore, there is only one caller, in calc_layout(), and it
is not much more than a simple wrapper for that function.
So get rid of ceph_calc_raw_layout() and embed it instead within
calc_layout().
While touching "osd_client.c", get rid of the unnecessary forward
declaration of __send_request().
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The only callers of ceph_osdc_init() and ceph_osdc_stop()
ceph_create_client() and ceph_destroy_client() (respectively)
and they are in the same kernel module as those two functions.
There's therefore no need to export those interfaces, so don't.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Two of the three callers of the osd client's send_queued() function
already hold the osd client mutex and drop it before the call.
Change send_queued() so it assumes the caller holds the mutex, and
update all callers accordingly. Rename it __send_queued() to match
the convention used elsewhere in the file with respect to the lock.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The "num_reply" parameter to ceph_osdc_new_request() is never
used inside that function, so get rid of it.
Note that ceph_sync_write() passes 2 for that argument, while all
other callers pass 1. It doesn't matter, but perhaps someone should
verify this doesn't indicate a problem.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
There is only one caller of ceph_osdc_writepages(), and it always
passes 0 as its "flags" argument. Get rid of that argument and
replace its use in ceph_osdc_writepages() with 0.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
There is only one caller of ceph_osdc_writepages(), and it always
passes 0 as its "dosync" argument. Get rid of that argument and
replace its use in ceph_osdc_writepages() with 0.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
There is only one caller of ceph_osdc_writepages(), and it always
passes the value true as its "nofail" argument. Get rid of that
argument and replace its use in ceph_osdc_writepages() with the
constant value true.
This and a number of cleanup patches that follow resolve:
http://tracker.ceph.com/issues/4126
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
There is a check in the completion path for osd requests that
ensures the number of pages allocated is enough to hold the amount
of incoming data expected.
For bio requests coming from rbd the "number of pages" is not really
meaningful (although total length would be). So stop requiring that
nr_pages be supplied for bio requests. This is done by checking
whether the pages pointer is null before checking the value of
nr_pages.
Note that this value is passed on to the messenger, but there it's
only used for debugging--it's never used for validation.
While here, change another spot that used r_pages in a debug message
inappropriately, and also invalidate the r_con_filling_msg pointer
after dropping a reference to it.
This resolves:
http://tracker.ceph.com/issues/3875
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Currently, if the OSD client finds an osd request has had a bio list
attached to it, it drops a reference to it (or rather, to the first
entry on that list) when the request is released.
The code that added that reference (i.e., the rbd client) is
therefore required to take an extra reference to that first bio
structure.
The osd client doesn't really do anything with the bio pointer other
than transfer it from the osd request structure to outgoing (for
writes) and ingoing (for reads) messages. So it really isn't the
right place to be taking or dropping references.
Furthermore, the rbd client already holds references to all bio
structures it passes to the osd client, and holds them until the
request is completed. So there's no need for this extra reference
whatsoever.
So remove the bio_put() call in ceph_osdc_release_request(), as
well as its matching bio_get() call in rbd_osd_req_create().
This change could lead to a crash if old libceph.ko was used with
new rbd.ko. Add a compatibility check at rbd initialization time to
avoid this possibilty.
This resolves:
http://tracker.ceph.com/issues/3798 and
http://tracker.ceph.com/issues/3799
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Both ceph_osdc_alloc_request() and ceph_osdc_build_request() are
provided an array of ceph osd request operations. Rather than just
passing the number of operations in the array, the caller is
required append an additional zeroed operation structure to signal
the end of the array.
All callers know the number of operations at the time these
functions are called, so drop the silly zero entry and supply that
number directly. As a result, get_num_ops() is no longer needed.
This also means that ceph_osdc_alloc_request() never uses its ops
argument, so that can be dropped.
Also rbd_create_rw_ops() no longer needs to add one to reserve room
for the additional op.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Only one of the two callers of ceph_osdc_alloc_request() provides
page or bio data for its payload. And essentially all that function
was doing with those arguments was assigning them to fields in the
osd request structure.
Simplify ceph_osdc_alloc_request() by having the caller take care of
making those assignments
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The only thing ceph_osdc_alloc_request() really does with the
flags value it is passed is assign it to the newly-created
osd request structure. Do that in the caller instead.
Both callers subsequently call ceph_osdc_build_request(), so have
that function (instead of ceph_osdc_alloc_request()) issue a warning
if a request comes through with neither the read nor write flags set.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The osdc parameter to ceph_calc_raw_layout() is not used, so get rid
of it. Consequently, the corresponding parameter in calc_layout()
becomes unused, so get rid of that as well.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
A snapshot id must be provided to ceph_calc_raw_layout() even though
it is not needed at all for calculating the layout.
Where the snapshot id *is* needed is when building the request
message for an osd operation.
Drop the snapid parameter from ceph_calc_raw_layout() and pass
that value instead in ceph_osdc_build_request().
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
ceph_calc_file_object_mapping() takes (among other things) a "file"
offset and length, and based on the layout, determines the object
number ("bno") backing the affected portion of the file's data and
the offset into that object where the desired range begins. It also
computes the size that should be used for the request--either the
amount requested or something less if that would exceed the end of
the object.
This patch changes the input length parameter in this function so it
is used only for input. That is, the argument will be passed by
value rather than by address, so the value provided won't get
updated by the function.
The value would only get updated if the length would surpass the
current object, and in that case the value it got updated to would
be exactly that returned in *oxlen.
Only one of the two callers is affected by this change. Update
ceph_calc_raw_layout() so it records any updated value.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The len argument to ceph_osdc_build_request() is set up to be
passed by address, but that function never updates its value
so there's no need to do this. Tighten up the interface by
passing the length directly.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Since every osd message is now prepared to include trailing data,
there's no need to check ahead of time whether any operations will
make use of the trail portion of the message.
We can drop the second argument to get_num_ops(), and as a result we
can also get rid of op_needs_trail() which is no longer used.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
An osd request structure contains an optional trail portion, which
if present will contain data to be passed in the payload portion of
the message containing the request. The trail field is a
ceph_pagelist pointer, and if null it indicates there is no trail.
A ceph_pagelist structure contains a length field, and it can
legitimately hold value 0. Make use of this to change the
interpretation of the "trail" of an osd request so that every osd
request has trailing data, it just might have length 0.
This means we change the r_trail field in a ceph_osd_request
structure from a pointer to a structure that is always initialized.
Note that in ceph_osdc_start_request(), the trail pointer (or now
address of that structure) is assigned to a ceph message's trail
field. Here's why that's still OK (looking at net/ceph/messenger.c):
- What would have resulted in a null pointer previously will now
refer to a 0-length page list. That message trail pointer
is used in two functions, write_partial_msg_pages() and
out_msg_pos_next().
- In write_partial_msg_pages(), a null page list pointer is
handled the same as a message with 0-length trail, and both
result in a "in_trail" variable set to false. The trail
pointer is only used if in_trail is true.
- The only other place the message trail pointer is used is
out_msg_pos_next(). That function is only called by
write_partial_msg_pages() and only touches the trail pointer
if the in_trail value it is passed is true.
Therefore a null ceph_msg->trail pointer is equivalent to a non-null
pointer referring to a 0-length page list structure.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
