* 'radix-tree' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/xfsdev:
radix-tree: radix_tree_range_tag_if_tagged() can set incorrect tags
radix-tree: clear all tags in radix_tree_node_rcu_free
Commit ebf8aa44be ("radix-tree:
omplement function radix_tree_range_tag_if_tagged") does not safely
set tags on on intermediate tree nodes. The code walks down the tree
setting tags before it has fully resolved the path to the leaf under
the assumption there will be a leaf slot with the tag set in the
range it is searching.
Unfortunately, this is not a valid assumption - we can abort after
setting a tag on an intermediate node if we overrun the number of
tags we are allowed to set in a batch, or stop scanning because we
we have passed the last scan index before we reach a leaf slot with
the tag we are searching for set.
As a result, we can leave the function with tags set on intemediate
nodes which can be tripped over later by tag-based lookups. The
result of these stale tags is that lookup may end prematurely or
livelock because the lookup cannot make progress.
The fix for the problem involves reocrding the traversal path we
take to the leaf nodes, and only propagating the tags back up the
tree once the tag is set in the leaf node slot. We are already
recording the path for efficient traversal, so there is no
additional overhead to do the intermediately node tag setting in
this manner.
This fixes a radix tree lookup livelock triggered by the new
writeback sync livelock avoidance code introduced in commit
f446daaea9 ("mm: implement writeback
livelock avoidance using page tagging").
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Acked-by: Jan Kara <jack@suse.cz>
Commit f446daaea9 ("mm: implement
writeback livelock avoidance using page tagging") introduced a new
radix tree tag, increasing the number of tags in each node from 2 to
3. It did not, however, fix up the code in
radix_tree_node_rcu_free() that cleans up after radix_tree_shrink()
and hence could leave stray tags set in the new tag array.
The result is that the livelock avoidance code added in the the
above commit would hit stale tags when doing tag based lookups,
resulting in livelocks when trying to traverse the tree.
Fix this problem in radix_tree_node_rcu_free() so it doesn't happen
again in the future by using a loop to walk all the tags up to
RADIX_TREE_MAX_TAGS to clear the stray tags radix_tree_shrink()
leaves behind.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Acked-by: Nick Piggin <npiggin@kernel.dk>
Acked-by: Jan Kara <jack@suse.cz>
When radix_tree_maxindex() is ~0UL, it can happen that scanning overflows
index and tree traversal code goes astray reading memory until it hits
unreadable memory. Check for overflow and exit in that case.
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, if RCU CPU stall warnings are enabled, they are enabled
immediately upon boot. They can be manually disabled via /sys (and
also re-enabled via /sys), and are automatically disabled upon panic.
However, some users need RCU CPU stalls to be disabled at boot time,
but to be enabled without rebuilding/rebooting. For example, someone
running a real-time application in production might not want the
additional latency of RCU CPU stall detection in normal operation, but
might need to enable it at any point for fault isolation purposes.
This commit therefore provides a new CONFIG_RCU_CPU_STALL_DETECTOR_RUNNABLE
kernel configuration parameter that maintains the current behavior
(enable at boot) by default, but allows a kernel to be configured
with RCU CPU stall detection built into the kernel, but disabled at
boot time.
Requested-by: Clark Williams <williams@redhat.com>
Requested-by: John Kacur <jkacur@redhat.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Also set the default to 60 seconds, up from the previous hard-coded timeout
of 10 seconds. This allows people who care to set short timeouts, while
avoiding people with unusual configurations (make randconfig!!!) from being
bothered with spurious CPU stall warnings.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
This commit provides definitions for the __rcu annotation defined earlier.
This annotation permits sparse to check for correct use of RCU-protected
pointers. If a pointer that is annotated with __rcu is accessed
directly (as opposed to via rcu_dereference(), rcu_assign_pointer(),
or one of their variants), sparse can be made to complain. To enable
such complaints, use the new default-disabled CONFIG_SPARSE_RCU_POINTER
kernel configuration option. Please note that these sparse complaints are
intended to be a debugging aid, -not- a code-style-enforcement mechanism.
There are special rcu_dereference_protected() and rcu_access_pointer()
accessors for use when RCU read-side protection is not required, for
example, when no other CPU has access to the data structure in question
or while the current CPU hold the update-side lock.
This patch also updates a number of docbook comments that were showing
their age.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Christopher Li <sparse@chrisli.org>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
warning: (LATENCYTOP && HAVE_LATENCYTOP_SUPPORT) selects
SCHED_DEBUG which has unmet direct dependencies (DEBUG_KERNEL &&
PROC_FS) warning: (LATENCYTOP && HAVE_LATENCYTOP_SUPPORT) selects
SCHEDSTATS which has unmet direct dependencies (DEBUG_KERNEL && PROC_FS)
Add depends on STACKTRACE_SUPPORT for 'select STACKTRACE'.
Add depends on PROC_FS since that is where the output goes.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
LKML-Reference: <20100812123121.a7c99cde.randy.dunlap@oracle.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of git://neil.brown.name/md:
Further tidyup of raid6 naming in lib/raid6
Make lib/raid6/test build correctly.
Rename raid6 files now they're in a 'raid6' directory.
Don't try and #include <linux/slab.h> in lib/inflate.c from the bootloader code
as linux/slab.h hauls in function defs that aren't available in the bootloader
code and may also haul in conflicting functions.
To fix this, make the inclusion of linux/slab.h contingent on NO_INFLATE_MALLOC
as are the usages of kmalloc() and kfree().
In MN10300, this causes the following errors:
In file included from include/linux/string.h:21,
from include/linux/bitmap.h:8,
from include/linux/nodemask.h:93,
from include/linux/mmzone.h:16,
from include/linux/gfp.h:4,
from include/linux/slab.h:12,
from arch/mn10300/boot/compressed/../../../../lib/inflate.c:106,
from arch/mn10300/boot/compressed/misc.c:170:
/warthog/am33/linux-2.6-mn10300/arch/mn10300/include/asm/string.h:19: error: conflicting types for 'memset'
arch/mn10300/boot/compressed/misc.c:59: error: previous definition of 'memset' was here
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix checkstack error:
lib/decompress_bunzip2.c: In function `get_next_block':
lib/decompress_bunzip2.c:511: warning: the frame size of 1932 bytes is larger than 1024 bytes
byteCount, symToByte, and mtfSymbol cannot be declared static or allocated
dynamically so place them in the bunzip_data struct.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Cc: Phillip Lougher <phillip@lougher.demon.co.uk>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We are missing the oops end marker for the exception based WARN implementation
in lib/bug.c. This is useful for logfile analysis tools.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are a few issues with the exception based WARN implementation in
lib/bug.c:
- Inconsistent printk flags. The "cut here" line is printed at KERN_EMERG, so
the console and all logged in users see the single line:
------------[ cut here ]------------
for each WARN. Fix this so we print everything at KERN_WARNING to match the
kernel/panic.c version.
- The lib/bug.c WARN would print "Badness at". Change it to match the
kernel/panic.c version which prints "WARNING: at".
- Print the list of modules, similar to kernel/panic.c of modules, similar to
kernel/panic.c
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://neil.brown.name/md: (24 commits)
md: clean up do_md_stop
md: fix another deadlock with removing sysfs attributes.
md: move revalidate_disk() back outside open_mutex
md/raid10: fix deadlock with unaligned read during resync
md/bitmap: separate out loading a bitmap from initialising the structures.
md/bitmap: prepare for storing write-intent-bitmap via dm-dirty-log.
md/bitmap: optimise scanning of empty bitmaps.
md/bitmap: clean up plugging calls.
md/bitmap: reduce dependence on sysfs.
md/bitmap: white space clean up and similar.
md/raid5: export raid5 unplugging interface.
md/plug: optionally use plugger to unplug an array during resync/recovery.
md/raid5: add simple plugging infrastructure.
md/raid5: export is_congested test
raid5: Don't set read-ahead when there is no queue
md: add support for raising dm events.
md: export various start/stop interfaces
md: split out md_rdev_init
md: be more careful setting MD_CHANGE_CLEAN
md/raid5: ensure we create a unique name for kmem_cache when mddev has no gendisk
...
* 'kmemleak' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-2.6-cm:
kmemleak: Fix typo in the comment
lib/scatterlist: Hook sg_kmalloc into kmemleak (v2)
kmemleak: Add DocBook style comments to kmemleak.c
kmemleak: Introduce a default off mode for kmemleak
kmemleak: Show more information for objects found by alias
More code can be pushed from rwsem_down_read_failed and
rwsem_down_write_failed into rwsem_down_failed_common.
Following change adding down_read_critical infrastructure support also
enjoys having flags available in a register rather than having to fish it
out in the struct rwsem_waiter...
Signed-off-by: Michel Lespinasse <walken@google.com>
Acked-by: David Howells <dhowells@redhat.com>
Cc: Mike Waychison <mikew@google.com>
Cc: Suleiman Souhlal <suleiman@google.com>
Cc: Ying Han <yinghan@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This change addresses the following situation:
- Thread A acquires the rwsem for read
- Thread B tries to acquire the rwsem for write, notices there is already
an active owner for the rwsem.
- Thread C tries to acquire the rwsem for read, notices that thread B already
tried to acquire it.
- Thread C grabs the spinlock and queues itself on the wait queue.
- Thread B grabs the spinlock and queues itself behind C. At this point A is
the only remaining active owner on the rwsem.
In this situation thread B could notice that it was the last active writer
on the rwsem, and decide to wake C to let it proceed in parallel with A
since they both only want the rwsem for read.
Signed-off-by: Michel Lespinasse <walken@google.com>
Acked-by: David Howells <dhowells@redhat.com>
Cc: Mike Waychison <mikew@google.com>
Cc: Suleiman Souhlal <suleiman@google.com>
Cc: Ying Han <yinghan@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Previously each waiting thread added a bias of RWSEM_WAITING_BIAS. With
this change, the bias is added only once to indicate that the wait list is
non-empty.
This has a few nice properties which will be used in following changes:
- when the spinlock is held and the waiter list is known to be non-empty,
count < RWSEM_WAITING_BIAS <=> there is an active writer on that sem
- count == RWSEM_WAITING_BIAS <=> there are waiting threads and no
active readers/writers on that sem
Signed-off-by: Michel Lespinasse <walken@google.com>
Acked-by: David Howells <dhowells@redhat.com>
Cc: Mike Waychison <mikew@google.com>
Cc: Suleiman Souhlal <suleiman@google.com>
Cc: Ying Han <yinghan@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In __rwsem_do_wake(), we can skip the active count check unless we come
there from up_xxxx(). Also when checking the active count, it is not
actually necessary to increment it; this allows us to get rid of the read
side undo code and simplify the calculation of the final rwsem count
adjustment once we've counted the reader threads to wake.
The basic observation is the following. When there are waiter threads on
a rwsem and the spinlock is held, other threads can only increment the
active count by trying to grab the rwsem in down_xxxx(). However
down_xxxx() will notice there are waiter threads and take the down_failed
path, blocking to acquire the spinlock on the way there. Therefore, a
thread observing an active count of zero with waiters queued and the
spinlock held, is protected against other threads acquiring the rwsem
until it wakes the last waiter or releases the spinlock.
Signed-off-by: Michel Lespinasse <walken@google.com>
Acked-by: David Howells <dhowells@redhat.com>
Cc: Mike Waychison <mikew@google.com>
Cc: Suleiman Souhlal <suleiman@google.com>
Cc: Ying Han <yinghan@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is in preparation for later changes in the series.
In __rwsem_do_wake(), the first queued waiter is checked first in order to
determine whether it's a writer or a reader. The code paths diverge at
this point. The code that checks and increments the rwsem active count is
duplicated on both sides - the point is that later changes in the series
will be able to independently modify both sides.
Signed-off-by: Michel Lespinasse <walken@google.com>
Acked-by: David Howells <dhowells@redhat.com>
Cc: Mike Waychison <mikew@google.com>
Cc: Suleiman Souhlal <suleiman@google.com>
Cc: Ying Han <yinghan@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Getting and putting arrays of pointers with flex arrays is a PITA. You
have to remember to pass &ptr to the _put and you have to do weird and
wacky casting to get the ptr back from the _get. Add two functions
flex_array_get_ptr() and flex_array_put_ptr() to handle all of the magic.
[akpm@linux-foundation.org: simplification suggested by Joe]
Signed-off-by: Eric Paris <eparis@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: Joe Perches <joe@perches.com>
Cc: James Morris <jmorris@namei.org>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The strict_strtoul() and strict_strtoull() functions used strlen() to
check argument's length in a situation where it wasn't strictly necessary
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Cc: "Yi Yang" <yi.y.yang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the magic LIST_POISON* values to detect an incorrect use of list_del
on a deleted entry. This DEBUG_LIST specific warning is easier to
understand than the generic Oops message caused by LIST_POISON
dereference.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A profile of a network benchmark showed iommu_num_pages rather high up:
0.52% iommu_num_pages
Looking at the profile, an integer divide is taking almost all of the time:
%
: c000000000376ea4 <.iommu_num_pages>:
1.93 : c000000000376ea4: fb e1 ff f8 std r31,-8(r1)
0.00 : c000000000376ea8: f8 21 ff c1 stdu r1,-64(r1)
0.00 : c000000000376eac: 7c 3f 0b 78 mr r31,r1
3.86 : c000000000376eb0: 38 84 ff ff addi r4,r4,-1
0.00 : c000000000376eb4: 38 05 ff ff addi r0,r5,-1
0.00 : c000000000376eb8: 7c 84 2a 14 add r4,r4,r5
46.95 : c000000000376ebc: 7c 00 18 38 and r0,r0,r3
45.66 : c000000000376ec0: 7c 84 02 14 add r4,r4,r0
0.00 : c000000000376ec4: 7c 64 2b 92 divdu r3,r4,r5
0.00 : c000000000376ec8: 38 3f 00 40 addi r1,r31,64
0.00 : c000000000376ecc: eb e1 ff f8 ld r31,-8(r1)
1.61 : c000000000376ed0: 4e 80 00 20 blr
Since every caller of iommu_num_pages passes in a constant power of two
we can inline this such that the divide is replaced by a shift. The
entire function is only a few instructions once optimised, so it is
a good candidate for inlining overall.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement function for setting one tag if another tag is set for each item
in given range.
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add percpu_counter_compare that allows for a quick but accurate comparison
of percpu_counter with a given value.
A rough count is provided by the count field in percpu_counter structure,
without accounting for the other values stored in individual cpu counters.
The actual count is a sum of count and the cpu counters. However, count
field is never different from the actual value by a factor of
batch*num_online_cpu. We do not need to get actual count for comparison
if count is different from the given value by this factor and allows for
quick comparison without summing up all the per cpu counters.
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (28 commits)
driver core: device_rename's new_name can be const
sysfs: Remove owner field from sysfs struct attribute
powerpc/pci: Remove owner field from attribute initialization in PCI bridge init
regulator: Remove owner field from attribute initialization in regulator core driver
leds: Remove owner field from attribute initialization in bd2802 driver
scsi: Remove owner field from attribute initialization in ARCMSR driver
scsi: Remove owner field from attribute initialization in LPFC driver
cgroupfs: create /sys/fs/cgroup to mount cgroupfs on
Driver core: Add BUS_NOTIFY_BIND_DRIVER
driver core: fix memory leak on one error path in bus_register()
debugfs: no longer needs to depend on SYSFS
sysfs: Fix one more signature discrepancy between sysfs implementation and docs.
sysfs: fix discrepancies between implementation and documentation
dcdbas: remove a redundant smi_data_buf_free in dcdbas_exit
dmi-id: fix a memory leak in dmi_id_init error path
sysfs: sysfs_chmod_file's attr can be const
firmware: Update hotplug script
Driver core: move platform device creation helpers to .init.text (if MODULE=n)
Driver core: reduce duplicated code for platform_device creation
Driver core: use kmemdup in platform_device_add_resources
...
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Ioremap: fix wrong physical address handling in PAT code
x86, tlb: Clean up and correct used type
x86, iomap: Fix wrong page aligned size calculation in ioremapping code
x86, mm: Create symbolic index into address_markers array
x86, ioremap: Fix normal ram range check
x86, ioremap: Fix incorrect physical address handling in PAE mode
x86-64, mm: Initialize VDSO earlier on 64 bits
x86, kmmio/mmiotrace: Fix double free of kmmio_fault_pages
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (162 commits)
tracing/kprobes: unregister_trace_probe needs to be called under mutex
perf: expose event__process function
perf events: Fix mmap offset determination
perf, powerpc: fsl_emb: Restore setting perf_sample_data.period
perf, powerpc: Convert the FSL driver to use local64_t
perf tools: Don't keep unreferenced maps when unmaps are detected
perf session: Invalidate last_match when removing threads from rb_tree
perf session: Free the ref_reloc_sym memory at the right place
x86,mmiotrace: Add support for tracing STOS instruction
perf, sched migration: Librarize task states and event headers helpers
perf, sched migration: Librarize the GUI class
perf, sched migration: Make the GUI class client agnostic
perf, sched migration: Make it vertically scrollable
perf, sched migration: Parameterize cpu height and spacing
perf, sched migration: Fix key bindings
perf, sched migration: Ignore unhandled task states
perf, sched migration: Handle ignored migrate out events
perf: New migration tool overview
tracing: Drop cpparg() macro
perf: Use tracepoint_synchronize_unregister() to flush any pending tracepoint call
...
Fix up trivial conflicts in Makefile and drivers/cpufreq/cpufreq.c
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
Revert "net: Make accesses to ->br_port safe for sparse RCU"
mce: convert to rcu_dereference_index_check()
net: Make accesses to ->br_port safe for sparse RCU
vfs: add fs.h to define struct file
lockdep: Add an in_workqueue_context() lockdep-based test function
rcu: add __rcu API for later sparse checking
rcu: add an rcu_dereference_index_check()
tree/tiny rcu: Add debug RCU head objects
mm: remove all rcu head initializations
fs: remove all rcu head initializations, except on_stack initializations
powerpc: remove all rcu head initializations
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
modpost: support objects with more than 64k sections
trivial: fix a typo in a filename
frv: clean up arch/frv/Makefile
kbuild: allow assignment to {A,C}FLAGS_KERNEL on the command line
kbuild: allow assignment to {A,C,LD}FLAGS_MODULE on the command line
Kbuild: Add option to set -femit-struct-debug-baseonly
Makefile: "make kernelrelease" should show the correct full kernel version
Makefile.build: make KBUILD_SYMTYPES work again
* 'for-linus' of git://git.monstr.eu/linux-2.6-microblaze: (49 commits)
microblaze: Add KGDB support
microblaze: Support brki rX, 0x18 for user application debugging
microblaze: Remove nop after MSRCLR/SET, MTS, MFS instructions
microblaze: Simplify syscall rutine
microblaze: Move PT_MODE saving to delay slot
microblaze: Fix _interrupt function
microblaze: Fix _user_exception function
microblaze: Put together addik instructions
microblaze: Use delay slot in syscall macros
microblaze: Save kernel mode in delay slot
microblaze: Do not mix register saving and mode setting
microblaze: Move SAVE_STATE upward
microblaze: entry.S: Macro optimization
microblaze: Optimize hw exception rutine
microblaze: Implement clear_ums macro and fix SAVE_STATE macro
microblaze: Remove additional setup for kernel_mode
microblaze: Optimize SAVE_STATE macro
microblaze: Remove additional loading
microblaze: Completely remove working with R11 register
microblaze: Do not setup BIP in _debug_exception
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1443 commits)
phy/marvell: add 88ec048 support
igb: Program MDICNFG register prior to PHY init
e1000e: correct MAC-PHY interconnect register offset for 82579
hso: Add new product ID
can: Add driver for esd CAN-USB/2 device
l2tp: fix export of header file for userspace
can-raw: Fix skb_orphan_try handling
Revert "net: remove zap_completion_queue"
net: cleanup inclusion
phy/marvell: add 88e1121 interface mode support
u32: negative offset fix
net: Fix a typo from "dev" to "ndev"
igb: Use irq_synchronize per vector when using MSI-X
ixgbevf: fix null pointer dereference due to filter being set for VLAN 0
e1000e: Fix irq_synchronize in MSI-X case
e1000e: register pm_qos request on hardware activation
ip_fragment: fix subtracting PPPOE_SES_HLEN from mtu twice
net: Add getsockopt support for TCP thin-streams
cxgb4: update driver version
cxgb4: add new PCI IDs
...
Manually fix up conflicts in:
- drivers/net/e1000e/netdev.c: due to pm_qos registration
infrastructure changes
- drivers/net/phy/marvell.c: conflict between adding 88ec048 support
and cleaning up the IDs
- drivers/net/wireless/ipw2x00/ipw2100.c: trivial ipw2100_pm_qos_req
conflict (registration change vs marking it static)
* 'stable/swiotlb-0.8.3' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb-2.6:
swiotlb: Make swiotlb bookkeeping functions visible in the header file.
swiotlb: search and replace "int dir" with "enum dma_data_direction dir"
swiotlb: Make internal bookkeeping functions have 'swiotlb_tbl' prefix.
swiotlb: add the swiotlb initialization function with iotlb memory
swiotlb: add swiotlb_tbl_map_single library function
Microblaze doesn't support frame pointers. Ftrace code
uses CALLER_ADDR1 which is defined in linux/ftrace.h. For Microblaze
is 0.
Signed-off-by: Michal Simek <monstr@monstr.eu>
kmemleak ignores page_alloc() and so believes the final sub-page
allocation using the plain kmalloc is decoupled and lost. This leads to
lots of false-positives with code that uses scatterlists.
The options seem to be either to tell kmemleak that the kmalloc is not
leaked or to notify kmemleak of the page allocations. The danger of the
first approach is that we may hide a real leak, so choose the latter
approach (of which I am not sure of the downsides).
v2: Added comments on the suggestion of Catalin.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
ARM has support for the atomic64_dec_if_positive operation
so ensure that it is tested by the atomic64_test routine.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The last 't' of 'fault' is missing in the description of FAIL_IO_TIMEOUT.
Signed-off-by: Takuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Introduce a new DEBUG_KMEMLEAK_DEFAULT_OFF config parameter that allows
kmemleak to be disabled by default, but enabled on the command line
via: kmemleak=on. Although a reboot is required to turn it on, its still
useful to not require a re-compile.
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Newer gcc has a -femit-struct-debug-baseonly option that dramatically
reduces the size of object files with debug info. What it does
is to only emit type information for structures when the structures
are defined in the same file or in a header file.
This means the type information for most headers are not included.
This is not good when the type information is actually
needed (e.g. with kgdb or systemtap)
But often kernel hackers only care about line numbers and don't
need all the type information anyways. In this case setting
the option can be a big win:
A build dir for a specific x86-64 configuration with gcc 4.5
shrunk from 2.3G to 1.2G. The compilation was also nearly a minute
faster.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
[mmarek: reformatted help text]
Signed-off-by: Michal Marek <mmarek@suse.cz>
via following scripts
FILES=$(find * -type f | grep -vE 'oprofile|[^K]config')
sed -i \
-e 's/lmb/memblock/g' \
-e 's/LMB/MEMBLOCK/g' \
$FILES
for N in $(find . -name lmb.[ch]); do
M=$(echo $N | sed 's/lmb/memblock/g')
mv $N $M
done
and remove some wrong change like lmbench and dlmb etc.
also move memblock.c from lib/ to mm/
Suggested-by: Ingo Molnar <mingo@elte.hu>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Current x86 ioremap() doesn't handle physical address higher than
32-bit properly in X86_32 PAE mode. When physical address higher than
32-bit is passed to ioremap(), higher 32-bits in physical address is
cleared wrongly. Due to this bug, ioremap() can map wrong address to
linear address space.
In my case, 64-bit MMIO region was assigned to a PCI device (ioat
device) on my system. Because of the ioremap()'s bug, wrong physical
address (instead of MMIO region) was mapped to linear address space.
Because of this, loading ioatdma driver caused unexpected behavior
(kernel panic, kernel hangup, ...).
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
LKML-Reference: <4C1AE680.7090408@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
rbtree: Undo augmented trees performance damage and regression
x86, Calgary: Limit the max PHB number to 256
Reimplement augmented RB-trees without sprinkling extra branches
all over the RB-tree code (which lives in the scheduler hot path).
This approach is 'borrowed' from Fabio's BFQ implementation and
relies on traversing the rebalance path after the RB-tree-op to
correct the heap property for insertion/removal and make up for
the damage done by the tree rotations.
For insertion the rebalance path is trivially that from the new
node upwards to the root, for removal it is that from the deepest
node in the path from the to be removed node that will still
be around after the removal.
[ This patch also fixes a video driver regression reported by
Ali Gholami Rudi - the memtype->subtree_max_end was updated
incorrectly. ]
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Venkatesh Pallipadi <venki@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Tested-by: Ali Gholami Rudi <ali@rudi.ir>
Cc: Fabio Checconi <fabio@gandalf.sssup.it>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <1275414172.27810.27961.camel@twins>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We should initialize the module dynamic debug datastructures
only after determining that the module is not loaded yet. This
fixes a bug that introduced in 2.6.35-rc2, where when a trying
to load a module twice, we also load it's dynamic printing data
twice which causes all sorts of nasty issues. Also handle
the dynamic debug cleanup later on failure.
Signed-off-by: Yehuda Sadeh <yehuda@hq.newdream.net>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (removed a #ifdef)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the ability to print a format and va_list from a structure pointer
Allows __dev_printk to be implemented as a single printk while
minimizing string space duplication.
%pV should not be used without some mechanism to verify the
format and argument use ala __attribute__(format (printf(...))).
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
fs/fs-writeback.c
Merge reason: Resolve the conflict
Note, i picked the version from Linus's tree, which effectively reverts
the fs-writeback.c bits of:
b97181f: fs: remove all rcu head initializations, except on_stack initializations
As the upstream changes to this file changed this code heavily and the
first attempt to resolve the conflict resulted in a non-booting kernel.
It's safer to re-try this portion of the commit cleanly.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
bitmap_find_next_zero_area requires the size of the bitmap, we instead
passed the last suitable position. This made it impossible to allocate
from the end of the pool.
Fixes a regression introduced by 243797f59b
("genalloc: use bitmap_find_next_zero_area").
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Cc: Zygo Blaxell <zygo.blaxell@xandros.com>
Cc: Tejun Heo <tj@kernel.org>
Acked-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert to rcu_dereference_raw() given that many callers may have many
different locking models.
Located-by: Miles Lane <miles.lane@gmail.com>
Tested-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Helps finding racy users of call_rcu(), which results in hangs because list
entries are overwritten and/or skipped.
Changelog since v4:
- Bissectability is now OK
- Now generate a WARN_ON_ONCE() for non-initialized rcu_head passed to
call_rcu(). Statically initialized objects are detected with
object_is_static().
- Rename rcu_head_init_on_stack to init_rcu_head_on_stack.
- Remove init_rcu_head() completely.
Changelog since v3:
- Include comments from Lai Jiangshan
This new patch version is based on the debugobjects with the newly introduced
"active state" tracker.
Non-initialized entries are all considered as "statically initialized". An
activation fixup (triggered by call_rcu()) takes care of performing the debug
object initialization without issuing any warning. Since we cannot increase the
size of struct rcu_head, I don't see much room to put an identifier for
statically initialized rcu_head structures. So for now, we have to live without
"activation without explicit init" detection. But the main purpose of this debug
option is to detect double-activations (double call_rcu() use of a rcu_head
before the callback is executed), which is correctly addressed here.
This also detects potential internal RCU callback corruption, which would cause
the callbacks to be executed twice.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
CC: David S. Miller <davem@davemloft.net>
CC: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
CC: akpm@linux-foundation.org
CC: mingo@elte.hu
CC: laijs@cn.fujitsu.com
CC: dipankar@in.ibm.com
CC: josh@joshtriplett.org
CC: dvhltc@us.ibm.com
CC: niv@us.ibm.com
CC: tglx@linutronix.de
CC: peterz@infradead.org
CC: rostedt@goodmis.org
CC: Valdis.Kletnieks@vt.edu
CC: dhowells@redhat.com
CC: eric.dumazet@gmail.com
CC: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Lai Jiangshan <laijs@cn.fujitsu.com>
We put the functions dealing with the operations on
the SWIOTLB buffer in the header and make those functions non-static.
And also make the functions exported via EXPORT_SYMBOL_GPL.
See "swiotlb: swiotlb: add swiotlb_tbl_map_single library function" for
full description of patchset.
[v2: swiotlb_sync_single_range_for_* no more. Remove usage.]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Tested-by: Albert Herranz <albert_herranz@yahoo.es>
.. to catch anybody doing something funky.
See "swiotlb: swiotlb: add swiotlb_tbl_map_single library function" for
full description of patchset.
[v2: swiotlb_sync_single_range_* no more - removed usage]
[v3: enum dma_data_direction direction -> enum dma_data_direction dir]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Tested-by: Albert Herranz <albert_herranz@yahoo.es>
The functions that operate on io_tlb_list/io_tlb_start/io_tlb_orig_addr
have the prefix 'swiotlb_tbl' now.
See "swiotlb: swiotlb: add swiotlb_tbl_map_single library function" for
full description of patchset.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Tested-by: Albert Herranz <albert_herranz@yahoo.es>
This enables the caller to initialize swiotlb with its own iotlb
memory.
See "swiotlb: swiotlb: add swiotlb_tbl_map_single library function" for
full description of patchset.
[v2: changed ..with_tlb to ..with_tbl]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Albert Herranz <albert_herranz@yahoo.es>
swiotlb_tbl_map_single() takes the dma address of iotlb instead of
using swiotlb_virt_to_bus().
[v2: changed swiotlb_tlb to swiotlb_tbl]
[v3: changed u64 to dma_addr_t]
This patch:
This is a set of patches that separate the address translation
(virt_to_phys, virt_to_bus, etc) and allocation of the SWIOTLB buffer
from the SWIOTLB library.
The idea behind this set of patches is to make it possible to have separate
mechanisms for translating virtual to physical or virtual to DMA addresses
on platforms which need an SWIOTLB, and where physical != PCI bus address
and also to allocate the core IOTLB memory outside SWIOTLB.
One customers of this is the pv-ops project, which can switch between
different modes of operation depending on the environment it is running in:
bare-metal or virtualized (Xen for now). Another is the Wii DMA - used to
implement the MEM2 DMA facility needed by its EHCI controller (for details:
http://lkml.org/lkml/2010/5/18/303)
On bare-metal SWIOTLB is used when there are no hardware IOMMU. In virtualized
environment it used when PCI pass-through is enabled for the guest. The problems
with PCI pass-through is that the guest's idea of PFN's is not the real thing.
To fix that, there is translation layer for PFN->machine frame number and vice-versa.
To bubble that up to the SWIOTLB layer there are two possible solutions.
One solution has been to wholesale copy the SWIOTLB, stick it in
arch/x86/xen/swiotlb.c and modify the virt_to_phys, phys_to_virt and others
to use the Xen address translation functions. Unfortunately, since the kernel can
run on bare-metal, there would be big code overlap with the real SWIOTLB.
(git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen.git xen/dom0/swiotlb-new)
Another approach, which this set of patches explores, is to abstract the
address translation and address determination functions away from the
SWIOTLB book-keeping functions. This way the core SWIOTLB library functions
are present in one place, while the address related functions are in
a separate library that can be loaded when running under non-bare-metal platform.
Changelog:
Since the last posting [v8.2] Konrad has done:
- Added this changelog in the patch and referenced in the other patches
this description.
- 'enum dma_data_direction direction' to 'enum dma.. dir' so to be
unified.
[v8-v8.2 changes:]
- Rolled-up the last two patches in one.
- Rebased against linus latest. That meant dealing with swiotlb_sync_single_range_* changes.
- added Acked-by: Fujita Tomonori and Tested-by: Albert Herranz
[v7-v8 changes:]
- Minimized the list of exported functions.
- Integrated Fujita's patches and changed "swiotlb_tlb" to "swiotlb_tbl" in them.
[v6-v7 changes:]
- Minimized the amount of exported functions/variable with a prefix of: "swiotbl_tbl".
- Made the usage of 'int dir' to be 'enum dma_data_direction'.
[v5-v6 changes:]
- Made the exported functions/variables have the 'swiotlb_bk' prefix.
- dropped the checkpatches/other reworks
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Albert Herranz <albert_herranz@yahoo.es>
Add s390 to list of architectures that have atomic64_dec_if_positive
implemented so we get rid of this warning:
lib/atomic64_test.c:129:2: warning: #warning Please implement
atomic64_dec_if_positive for your architecture, and add it to the IF above
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Luca Barbieri <luca@luca-barbieri.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a kfree(ue_sk) missing on the error path if
netlink_kernel_create() fails.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
lib/kobject_uevent.c:87: warning: 'kobj_bcast_filter' defined but not used
Repairs "hotplug: netns aware uevent_helper"
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, cpufeature: Unbreak compile with gcc 3.x
x86, pat: Fix memory leak in free_memtype
x86, k8: Fix section mismatch for powernowk8_exit()
lib/atomic64_test: fix missing include of linux/kernel.h
x86: remove last traces of quicklist usage
x86, setup: Phoenix BIOS fixup is needed on Dell Inspiron Mini 1012
x86: "nosmp" command line option should force the system into UP mode
arch/x86/pci: use kasprintf
x86, apic: ack all pending irqs when crashed/on kexec
This reverts commit 0ac0c0d0f8, which
caused cross-architecture build problems for all the wrong reasons.
IA64 already added its own version of __node_random(), but the fact is,
there is nothing architectural about the function, and the original
commit was just badly done. Revert it, since no fix is forthcoming.
Requested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
radix_tree_prev_hole() used LONG_MAX to detect underflow; however,
ULONG_MAX is clearly what was intended, both here and by its only user
(count_history_pages at mm/readahead.c).
Reviewed-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
swiotlb_sync_single_range_for_cpu and swiotlb_sync_single_range_for_device
are unnecessary because swiotlb_sync_single_for_cpu and
swiotlb_sync_single_for_device can be used instead.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch moves the definition of struct rnd_state and the inline
__seed() function to linux/random.h. It renames the static __random32()
function to prandom32() and exports it for use in modules.
prandom32() is useful as a privately-seeded pseudo random number generator
that can give the same result every time it is initialized.
For FCoE FC-BB-6 VN2VN mode self-selected unique FC address generation, we
need an pseudo-random number generator seeded with the 64-bit world-wide
port name. A truly random generator or one seeded with randomness won't
do because the same sequence of numbers should be generated each time we
boot or the link comes up.
A prandom32_seed() inline function is added to the header file. It is
inlined not for speed, but so the function won't be expanded in the base
kernel, but only in the module that uses it.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Acked-by: Matt Mackall <mpm@selenic.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently idr_remove_all will fail with a use after free error if
idr::layers is bigger than 2, which on 32 bit systems corresponds to items
more than 1024. This is due to stepping back too many levels during
backtracking. For simplicity let's assume that IDR_BITS=1 -> we have 2
nodes at each level below the root node and each leaf node stores two IDs.
(In reality for 32 bit systems IDR_BITS=5, with 32 nodes at each sub-root
level and 32 IDs in each leaf node). The sequence of freeing the nodes at
the moment is as follows:
layer
1 -> a(7)
2 -> b(3) c(5)
3 -> d(1) e(2) f(4) g(6)
Until step 4 things go fine, but then node c is freed, whereas node g
should be freed first. Since node c contains the pointer to node g we'll
have a use after free error at step 6.
How many levels we step back after visiting the leaf nodes is currently
determined by the msb of the id we are currently visiting:
Step
1. node d with IDs 0,1 is freed, current ID is advanced to 2.
msb of the current ID bit 1. This means we need to step back
1 level to node b and take the next sibling, node e.
2-3. node e with IDs 2,3 is freed, current ID is 4, msb is bit 2.
This means we need to step back 2 levels to node a, freeing
node b on the way.
4-5. node f with IDs 4,5 is freed, current ID is 6, msb is still
bit 2. This means we again need to step back 2 levels to node
a and free c on the way.
6. We should visit node g, but its pointer is not available as
node c was freed.
The fix changes how we determine the number of levels to step back.
Instead of deducting this merely from the msb of the current ID, we should
really check if advancing the ID causes an overflow to a bit position
corresponding to a given layer. In the above example overflow from bit 0
to bit 1 should mean stepping back 1 level. Overflow from bit 1 to bit 2
should mean stepping back 2 levels and so on.
The fix was tested with IDs up to 1 << 20, which corresponds to 4 layers
on 32 bit systems.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
Cc: Eric Paris <eparis@redhat.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: <stable@kernel.org> [2.6.34.1]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I used this module to test the series of modification to the cpu notifiers
code.
Example1: inject CPU offline error (-1 == -EPERM)
# modprobe cpu-notifier-error-inject cpu_down_prepare_error=-1
# echo 0 > /sys/devices/system/cpu/cpu1/online
bash: echo: write error: Operation not permitted
Example2: inject CPU online error (-2 == -ENOENT)
# modprobe cpu-notifier-error-inject cpu_up_prepare_error=-2
# echo 1 > /sys/devices/system/cpu/cpu1/online
bash: echo: write error: No such file or directory
[akpm@linux-foundation.org: fix Kconfig help text]
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some workloads that create a large number of small files tend to assign
too many pages to node 0 (multi-node systems). Part of the reason is that
the rotor (in cpuset_mem_spread_node()) used to assign nodes starts at
node 0 for newly created tasks.
This patch changes the rotor to be initialized to a random node number of
the cpuset.
[akpm@linux-foundation.org: fix layout]
[Lee.Schermerhorn@hp.com: Define stub numa_random() for !NUMA configuration]
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Paul Menage <menage@google.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It doesn't work on big-endian - those architectures don't define
__LITTLE_ENDIAN.
Cc: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since crc32.c contains a nifty test program that can be executed in user
space, make sure endian detection works reliably in user space too.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Precompute more crc32 values(0xcc00, 0xcc0000 and 0xcc000000) into tables.
This increases the table size from 1KB to 4KB but the performance benfit
makes it worth it:
28% faster on MPC8321, 266 MHz
2x faster on Core 2 Duo, 3.1GHz
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
hex_to_bin() is a little method which converts hex digit to its actual
value. There are plenty of places where such functionality is needed.
[akpm@linux-foundation.org: use tolower(), saving 3 bytes, test the more common case first - it's quicker]
[akpm@linux-foundation.org: relocate tolower to make it even faster! (Joe)]
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: Duncan Sands <duncan.sands@free.fr>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: "Richard Russon (FlatCap)" <ldm@flatcap.org>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reduce char linebuf[200] to the actual size required., which is 32 * 3 + 2
+ 32 + 1, ie: linebuf[131].
Change examples to use bool true not int 1.
Align multiline argument indentation to open parenthesis.
Use temporary for ptr[j] so trigraph fits on single line.
Convert printk ptr from %*p, (int)(2 * sizeof(void *)) to %p as %p uses
the same calculation for size.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This doesn't change behavior at all. In the original code, if nwords was
zero then ddebug_parse_query() would return -EINVAL, now we just do it
earlier.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- C99 knows about USHRT_MAX/SHRT_MAX/SHRT_MIN, not
USHORT_MAX/SHORT_MAX/SHORT_MIN.
- Make SHRT_MIN of type s16, not int, for consistency.
[akpm@linux-foundation.org: fix drivers/dma/timb_dma.c]
[akpm@linux-foundation.org: fix security/keys/keyring.c]
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a build-failure
(http://kisskb.ellerman.id.au/kisskb/buildresult/2601239/) by adding the
missing include file (linux/kernel.h) for printk and KERN_INFO.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
LKML-Reference: <201005241913.o4OJDKdf010884@imap1.linux-foundation.org>
Cc: Luca Barbieri <luca@luca-barbieri.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
* git://git.infradead.org/iommu-2.6:
intel-iommu: Set a more specific taint flag for invalid BIOS DMAR tables
intel-iommu: Combine the BIOS DMAR table warning messages
panic: Add taint flag TAINT_FIRMWARE_WORKAROUND ('I')
panic: Allow warnings to set different taint flags
intel-iommu: intel_iommu_map_range failed at very end of address space
intel-iommu: errors with smaller iommu widths
intel-iommu: Fix boot inside 64bit virtualbox with io-apic disabled
intel-iommu: use physfn to search drhd for VF
intel-iommu: Print out iommu seq_id
intel-iommu: Don't complain that ACPI_DMAR_SCOPE_TYPE_IOAPIC is not supported
intel-iommu: Avoid global flushes with caching mode.
intel-iommu: Use correct domain ID when caching mode is enabled
intel-iommu mistakenly uses offset_pfn when caching mode is enabled
intel-iommu: use for_each_set_bit()
intel-iommu: Fix section mismatch dmar_ir_support() uses dmar_tbl.
* 'kdb-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb: (25 commits)
kdb,debug_core: Allow the debug core to receive a panic notification
MAINTAINERS: update kgdb, kdb, and debug_core info
debug_core,kdb: Allow the debug core to process a recursive debug entry
printk,kdb: capture printk() when in kdb shell
kgdboc,kdb: Allow kdb to work on a non open console port
kgdb: Add the ability to schedule a breakpoint via a tasklet
mips,kgdb: kdb low level trap catch and stack trace
powerpc,kgdb: Introduce low level trap catching
x86,kgdb: Add low level debug hook
kgdb: remove post_primary_code references
kgdb,docs: Update the kgdb docs to include kdb
kgdboc,keyboard: Keyboard driver for kdb with kgdb
kgdb: gdb "monitor" -> kdb passthrough
sparc,sunzilog: Add console polling support for sunzilog serial driver
sh,sh-sci: Use NO_POLL_CHAR in the SCIF polled console code
kgdb,8250,pl011: Return immediately from console poll
kgdb: core changes to support kdb
kdb: core for kgdb back end (2 of 2)
kdb: core for kgdb back end (1 of 2)
kgdb,blackfin: Add in kgdb_arch_set_pc for blackfin
...
It only makes sense for uevent_helper to get events
in the intial namespaces. It's invocation is not
per namespace and it is not clear how we could make
it's invocation namespace aware.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Utilize netlink_broacast_filtered to allow sending hotplug events
in the proper namespace.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Open a copy of the uevent kernel socket in each network
namespace so we can send uevents in all network namespaces.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add some in-line comments to explain the new infrastructure, which
was introduced to support sysfs directory tagging with namespaces.
I think an overall description someplace might be good too, but it
didn't really seem to fit into Documentation/filesystems/sysfs.txt,
which appears more geared toward users, rather than maintainers, of
sysfs.
(Tejun, please let me know if I can make anything clearer or failed
altogether to comment something that should be commented.)
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The problem. When implementing a network namespace I need to be able
to have multiple network devices with the same name. Currently this
is a problem for /sys/class/net/*, /sys/devices/virtual/net/*, and
potentially a few other directories of the form /sys/ ... /net/*.
What this patch does is to add an additional tag field to the
sysfs dirent structure. For directories that should show different
contents depending on the context such as /sys/class/net/, and
/sys/devices/virtual/net/ this tag field is used to specify the
context in which those directories should be visible. Effectively
this is the same as creating multiple distinct directories with
the same name but internally to sysfs the result is nicer.
I am calling the concept of a single directory that looks like multiple
directories all at the same path in the filesystem tagged directories.
For the networking namespace the set of directories whose contents I need
to filter with tags can depend on the presence or absence of hotplug
hardware or which modules are currently loaded. Which means I need
a simple race free way to setup those directories as tagged.
To achieve a reace free design all tagged directories are created
and managed by sysfs itself.
Users of this interface:
- define a type in the sysfs_tag_type enumeration.
- call sysfs_register_ns_types with the type and it's operations
- sysfs_exit_ns when an individual tag is no longer valid
- Implement mount_ns() which returns the ns of the calling process
so we can attach it to a sysfs superblock.
- Implement ktype.namespace() which returns the ns of a syfs kobject.
Everything else is left up to sysfs and the driver layer.
For the network namespace mount_ns and namespace() are essentially
one line functions, and look to remain that.
Tags are currently represented a const void * pointers as that is
both generic, prevides enough information for equality comparisons,
and is trivial to create for current users, as it is just the
existing namespace pointer.
The work needed in sysfs is more extensive. At each directory
or symlink creating I need to check if the directory it is being
created in is a tagged directory and if so generate the appropriate
tag to place on the sysfs_dirent. Likewise at each symlink or
directory removal I need to check if the sysfs directory it is
being removed from is a tagged directory and if so figure out
which tag goes along with the name I am deleting.
Currently only directories which hold kobjects, and
symlinks are supported. There is not enough information
in the current file attribute interfaces to give us anything
to discriminate on which makes it useless, and there are
no potential users which makes it an uninteresting problem
to solve.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move complete knowledge of namespaces into the kobject layer
so we can use that information when reporting kobjects to
userspace.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Of the three uses of kref_set in the kernel:
One really should be kref_put as the code is letting go of a
reference,
Two really should be kref_init because the kref is being
initialised.
This suggests that making kref_set available encourages bad code.
So fix the three uses and remove kref_set completely.
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Mimi Zohar <zohar@us.ibm.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.infradead.org/mtd-2.6: (154 commits)
mtd: cfi_cmdset_0002: use AMD standard command-set with Winbond flash chips
mtd: cfi_cmdset_0002: Fix MODULE_ALIAS and linkage for new 0701 commandset ID
mtd: mxc_nand: Remove duplicate NAND_CMD_RESET case value
mtd: update gfp/slab.h includes
jffs2: Stop triggering block erases from jffs2_write_super()
jffs2: Rename jffs2_erase_pending_trigger() to jffs2_dirty_trigger()
jffs2: Use jffs2_garbage_collect_trigger() to trigger pending erases
jffs2: Require jffs2_garbage_collect_trigger() to be called with lock held
jffs2: Wake GC thread when there are blocks to be erased
jffs2: Erase pending blocks in GC pass, avoid invalid -EIO return
jffs2: Add 'work_done' return value from jffs2_erase_pending_blocks()
mtd: mtdchar: Do not corrupt backing device of device node inode
mtd/maps/pcmciamtd: Fix printk format for ssize_t in debug messages
drivers/mtd: Use kmemdup
mtd: cfi_cmdset_0002: Fix argument order in bootloc warning
mtd: nand: add Toshiba TC58NVG0 device ID
pcmciamtd: add another ID
pcmciamtd: coding style cleanups
pcmciamtd: fixing obvious errors
mtd: chips: add SST39WF160x NOR-flashes
...
Trivial conflicts due to dev_node removal in drivers/mtd/maps/pcmciamtd.c
The only way the debugger can handle a trap in inside rcu_lock,
notify_die, or atomic_notifier_call_chain without a recursive fault is
to have a low level "first opportunity handler" do_trap_or_bp() handler.
Generally this will be something the vast majority of folks will not
need, but for those who need it, it is added as a kernel .config
option called KGDB_LOW_LEVEL_TRAP.
Also added was a die notification for oops such that kdb can catch an
oops for analysis.
There appeared to be no obvious way to pass the struct pt_regs from
the original exception back to the stack back tracer, so a special
case was added to show_stack() for when kdb is active because you
generally desire to generally look at the back trace of the original
exception.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
The only way the debugger can handle a trap in inside rcu_lock,
notify_die, or atomic_notifier_call_chain without a triple fault is
to have a low level "first opportunity handler" in the int3 exception
handler.
Generally this will be something the vast majority of folks will not
need, but for those who need it, it is added as a kernel .config
option called KGDB_LOW_LEVEL_TRAP.
CC: Ingo Molnar <mingo@elte.hu>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: H. Peter Anvin <hpa@zytor.com>
CC: x86@kernel.org
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
This patch adds in the kdb PS/2 keyboard driver. This was mostly a
direct port from the original kdb where I cleaned up the code against
checkpatch.pl and added the glue to stitch it into kgdb.
This patch also enables early kdb debug via kgdbwait and the keyboard.
All the access to configure kdb using either a serial console or the
keyboard is done via kgdboc.
If you want to use only the keyboard and want to break in early you
would add to your kernel command arguments:
kgdboc=kbd kgdbwait
If you wanted serial and or the keyboard access you could use:
kgdboc=kbd,ttyS0
You can also configure kgdboc as a kernel module or at run time with
the sysfs where you can activate and deactivate kgdb.
Turn it on:
echo kbd,ttyS0 > /sys/module/kgdboc/parameters/kgdboc
Turn it off:
echo "" > /sys/module/kgdboc/parameters/kgdboc
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
These are the minimum changes to the kgdb core in order to enable an
API to connect a new front end (kdb) to the debug core.
This patch introduces the dbg_kdb_mode variable controls where the
user level I/O is routed. It will be routed to the gdbstub (kgdb) or
to the kdb front end which is a simple shell available over the kgdboc
connection.
You can switch back and forth between kdb or the gdb stub mode of
operation dynamically. From gdb stub mode you can blindly type
"$3#33", or from the kdb mode you can enter "kgdb" to switch to the
gdb stub.
The logic in the debug core depends on kdb to look for the typical gdb
connection sequences and return immediately with KGDB_PASS_EVENT if a
gdb serial command sequence is detected. That should allow a
reasonably seamless transition between kdb -> gdb without leaving the
kernel exception state. The two gdb serial queries that kdb is
responsible for detecting are the "?" and "qSupported" packets.
CC: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Martin Hicks <mort@sgi.com>
There are many different UUID/GUID definitions in kernel, such as that
in EFI, many file systems, some drivers, etc. Every kernel components
need UUID/GUID has its own definition. This patch provides a unified
definition for UUID/GUID.
UUID is defined via typedef. This makes that UUID appears more like a
preliminary type, and makes the data type explicit (comparing with
implicit "u8 uuid[16]").
The binary representation of UUID/GUID can be little-endian (used by
EFI, etc) or big-endian (defined by RFC4122), so both is defined.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The lockup detector is a new feature that now involves the
nmi watchdog. Drop the default y and let the user choose.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
WARN() is used in some places to report firmware or hardware bugs that
are then worked-around. These bugs do not affect the stability of the
kernel and should not set the flag for TAINT_WARN. To allow for this,
add WARN_TAINT() and WARN_TAINT_ONCE() macros that take a taint number
as argument.
Architectures that implement warnings using trap instructions instead
of calls to warn_slowpath_*() now implement __WARN_TAINT(taint)
instead of __WARN().
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Helge Deller <deller@gmx.de>
Tested-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'x86-pat-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, pat: Update the page flags for memtype atomically instead of using memtype_lock
x86, pat: In rbt_memtype_check_insert(), update new->type only if valid
x86, pat: Migrate to rbtree only backend for pat memtype management
x86, pat: Preparatory changes in pat.c for bigger rbtree change
rbtree: Add support for augmented rbtrees
* 'core-hweight-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, hweight: Use a 32-bit popcnt for __arch_hweight32()
arch, hweight: Fix compilation errors
x86: Add optimized popcnt variants
bitops: Optimize hweight() by making use of compile-time evaluation
* 'x86-atomic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix LOCK_PREFIX_HERE for uniprocessor build
x86, atomic64: In selftest, distinguish x86-64 from 586+
x86-32: Fix atomic64_inc_not_zero return value convention
lib: Fix atomic64_inc_not_zero test
lib: Fix atomic64_add_unless return value convention
x86-32: Fix atomic64_add_unless return value convention
lib: Fix atomic64_add_unless test
x86: Implement atomic[64]_dec_if_positive()
lib: Only test atomic64_dec_if_positive on archs having it
x86-32: Rewrite 32-bit atomic64 functions in assembly
lib: Add self-test for atomic64_t
x86-32: Allow UP/SMP lock replacement in cmpxchg64
x86: Add support for lock prefix in alternatives
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (24 commits)
rcu: remove all rcu head initializations, except on_stack initializations
rcu head introduce rcu head init on stack
Debugobjects transition check
rcu: fix build bug in RCU_FAST_NO_HZ builds
rcu: RCU_FAST_NO_HZ must check RCU dyntick state
rcu: make SRCU usable in modules
rcu: improve the RCU CPU-stall warning documentation
rcu: reduce the number of spurious RCU_SOFTIRQ invocations
rcu: permit discontiguous cpu_possible_mask CPU numbering
rcu: improve RCU CPU stall-warning messages
rcu: print boot-time console messages if RCU configs out of ordinary
rcu: disable CPU stall warnings upon panic
rcu: enable CPU_STALL_VERBOSE by default
rcu: slim down rcutiny by removing rcu_scheduler_active and friends
rcu: refactor RCU's context-switch handling
rcu: rename rcutiny rcu_ctrlblk to rcu_sched_ctrlblk
rcu: shrink rcutiny by making synchronize_rcu_bh() be inline
rcu: fix now-bogus rcu_scheduler_active comments.
rcu: Fix bogus CONFIG_PROVE_LOCKING in comments to reflect reality.
rcu: ignore offline CPUs in last non-dyntick-idle CPU check
...
This new config is deemed to simplify even more the lockup detector
dependencies and can make it easier to bring a smooth sorting
between archs that support the new generic lockup detector and those
that still have their own, especially for those that are in the
middle of this migration.
Instead of checking whether we have CONFIG_LOCKUP_DETECTOR +
CONFIG_PERF_EVENTS_NMI each time an arch wants to know if it needs
to build its own lockup detector, take a shortcut with this new
config. It is enabled only if the hardlockup detection part of
the whole lockup detector is on.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
We kept CONFIG_DETECT_SOFTLOCKUP around for compatibility with
older configs. But it was enabled by default if CONFIG_DEBUG_KERNEL.
So if we want to enable CONFIG_LOCKUP_DETECTOR on configs that had
CONFIG_DETECT_SOFTLOCKUP, all we need is to have the same enabling
by default if CONFIG_DEBUG_KERNEL. We can then remove
CONFIG_DETECT_SOFTLOCKUP directly.
So tag CONFIG_LOCKUP_DETECTOR as default y. This is what we want for
most serious kernel debugging anyway.
And also forbid the lockup detector in S390 as it was for the
previous softlockup detector, event though the true reason for that
is not outlined.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
If there are no active threasd using a semaphore, it is always correct
to unqueue blocked threads. This seems to be what was intended in the
undo code.
What was done instead, was to look for a sem count of zero - this is an
impossible situation, given that at least one thread is known to be
queued on the semaphore. The code might be correct as written, but it's
hard to reason about and it's not what was intended (otherwise the goto
out would have been unconditional).
Go for checking the active count - the alternative is not worth the
headache.
Signed-off-by: Michel Lespinasse <walken@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Panic on softlockups was still depending on the softlockup detector.
But the latter has been merged into the lockup detector now.
Let's update this config dependency.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Eric Paris <eparis@redhat.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
The new nmi_watchdog (which uses the perf event subsystem) is very
similar in structure to the softlockup detector. Using Ingo's
suggestion, I combined the two functionalities into one file:
kernel/watchdog.c.
Now both the nmi_watchdog (or hardlockup detector) and softlockup
detector sit on top of the perf event subsystem, which is run every
60 seconds or so to see if there are any lockups.
To detect hardlockups, cpus not responding to interrupts, I
implemented an hrtimer that runs 5 times for every perf event
overflow event. If that stops counting on a cpu, then the cpu is
most likely in trouble.
To detect softlockups, tasks not yielding to the scheduler, I used the
previous kthread idea that now gets kicked every time the hrtimer fires.
If the kthread isn't being scheduled neither is anyone else and the
warning is printed to the console.
I tested this on x86_64 and both the softlockup and hardlockup paths
work.
V2:
- cleaned up the Kconfig and softlockup combination
- surrounded hardlockup cases with #ifdef CONFIG_PERF_EVENTS_NMI
- seperated out the softlockup case from perf event subsystem
- re-arranged the enabling/disabling nmi watchdog from proc space
- added cpumasks for hardlockup failure cases
- removed fallback to soft events if no PMU exists for hard events
V3:
- comment cleanups
- drop support for older softlockup code
- per_cpu cleanups
- completely remove software clock base hardlockup detector
- use per_cpu masking on hard/soft lockup detection
- #ifdef cleanups
- rename config option NMI_WATCHDOG to LOCKUP_DETECTOR
- documentation additions
V4:
- documentation fixes
- convert per_cpu to __get_cpu_var
- powerpc compile fixes
V5:
- split apart warn flags for hard and soft lockups
TODO:
- figure out how to make an arch-agnostic clock2cycles call
(if possible) to feed into perf events as a sample period
[fweisbec: merged conflict patch]
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Eric Paris <eparis@redhat.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
LKML-Reference: <1273266711-18706-2-git-send-email-dzickus@redhat.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Implement a basic state machine checker in the debugobjects.
This state machine checker detects races and inconsistencies within the "active"
life of a debugobject. The checker only keeps track of the current state; all
the state machine logic is kept at the object instance level.
The checker works by adding a supplementary "unsigned int astate" field to the
debug_obj structure. It keeps track of the current "active state" of the object.
The only constraints that are imposed on the states by the debugobjects system
is that:
- activation of an object sets the current active state to 0,
- deactivation of an object expects the current active state to be 0.
For the rest of the states, the state mapping is determined by the specific
object instance. Therefore, the logic keeping track of the state machine is
within the specialized instance, without any need to know about it at the
debugobject level.
The current object active state is changed by calling:
debug_object_active_state(addr, descr, expect, next)
where "expect" is the expected state and "next" is the next state to move to if
the expected state is found. A warning is generated if the expected is not
found.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David S. Miller <davem@davemloft.net>
CC: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
CC: akpm@linux-foundation.org
CC: mingo@elte.hu
CC: laijs@cn.fujitsu.com
CC: dipankar@in.ibm.com
CC: josh@joshtriplett.org
CC: dvhltc@us.ibm.com
CC: niv@us.ibm.com
CC: peterz@infradead.org
CC: rostedt@goodmis.org
CC: Valdis.Kletnieks@vt.edu
CC: dhowells@redhat.com
CC: eric.dumazet@gmail.com
CC: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The CPU_STALL_VERBOSE kernel configuration parameter was added to
2.6.34 to identify any preempted/blocked tasks that were preventing
the current grace period from completing when running preemptible
RCU. As is conventional for new configurations parameters, this
defaulted disabled. It is now time to enable it by default.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
There is no need to disable lockdep after an RCU lockdep splat,
so remove the debug_lockdeps_off() from lockdep_rcu_dereference().
To avoid repeated lockdep splats, use a static variable in the inlined
rcu_dereference_check() and rcu_dereference_protected() macros so that
a given instance splats only once, but so that multiple instances can
be detected per boot.
This is controlled by a new config variable CONFIG_PROVE_RCU_REPEATEDLY,
which is disabled by default. This provides the normal lockdep behavior
by default, but permits people who want to find multiple RCU-lockdep
splats per boot to easily do so.
Requested-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Tested-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Merge reason:
Conflict between LOCK_PREFIX_HERE and relative alternatives
pointers
Resolved Conflicts:
arch/x86/include/asm/alternative.h
arch/x86/kernel/alternative.c
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Add a missing EXPORT_SYMBOL.
I must be the first person that wants to use this function :-)
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes 2 issues with the LZO decompressor:
- It doesn't handle the case where a block isn't compressed at all. In
this case, calling lzo1x_decompress_safe will fail, so we need to just
use memcpy() instead (the upstream LZO code does something similar)
- Since commit 54291362d2 ("initramfs: add
missing decompressor error check") , the decompressor return code is
checked in the init/initramfs.c The LZO decompressor didn't return the
expected value, causing the initramfs code to falsely believe a
decompression error occured
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Tested-by: bert schulze <spambemyguest@googlemail.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
memset() is called with the wrong address and the kernel panics.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: David Rientjes <rientjes@google.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit ef0658f3de changed precision
from int to s8.
There is existing kernel code that uses a larger precision.
An example from the audit code:
vsnprintf(...,..., " msg='%.1024s'", (char *)data);
which overflows precision and truncates to nothing.
Extending precision size fixes the audit system issue.
Other changes:
Change the size of the struct printf_spec.type from u16 to u8 so
sizeof(struct printf_spec) stays as small as possible.
Reorder the struct members so sizeof(struct printf_spec) remains 64 bits
without alignment holes.
Document the struct members a bit more.
Original-patch-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block: (34 commits)
cfq-iosched: Fix the incorrect timeslice accounting with forced_dispatch
loop: Update mtime when writing using aops
block: expose the statistics in blkio.time and blkio.sectors for the root cgroup
backing-dev: Handle class_create() failure
Block: Fix block/elevator.c elevator_get() off-by-one error
drbd: lc_element_by_index() never returns NULL
cciss: unlock on error path
cfq-iosched: Do not merge queues of BE and IDLE classes
cfq-iosched: Add additional blktrace log messages in CFQ for easier debugging
i2o: Remove the dangerous kobj_to_i2o_device macro
block: remove 16 bytes of padding from struct request on 64bits
cfq-iosched: fix a kbuild regression
block: make CONFIG_BLK_CGROUP visible
Remove GENHD_FL_DRIVERFS
block: Export max number of segments and max segment size in sysfs
block: Finalize conversion of block limits functions
block: Fix overrun in lcm() and move it to lib
vfs: improve writeback_inodes_wb()
paride: fix off-by-one test
drbd: fix al-to-on-disk-bitmap for 4k logical_block_size
...
radix_tree_tag_get() is not safe to use concurrently with radix_tree_tag_set()
or radix_tree_tag_clear(). The problem is that the double tag_get() in
radix_tree_tag_get():
if (!tag_get(node, tag, offset))
saw_unset_tag = 1;
if (height == 1) {
int ret = tag_get(node, tag, offset);
may see the value change due to the action of set/clear. RCU is no protection
against this as no pointers are being changed, no nodes are being replaced
according to a COW protocol - set/clear alter the node directly.
The documentation in linux/radix-tree.h, however, says that
radix_tree_tag_get() is an exception to the rule that "any function modifying
the tree or tags (...) must exclude other modifications, and exclude any
functions reading the tree".
The problem is that the next statement in radix_tree_tag_get() checks that the
tag doesn't vary over time:
BUG_ON(ret && saw_unset_tag);
This has been seen happening in FS-Cache:
https://www.redhat.com/archives/linux-cachefs/2010-April/msg00013.html
To this end, remove the BUG_ON() from radix_tree_tag_get() and note in various
comments that the value of the tag may change whilst the RCU read lock is held,
and thus that the return value of radix_tree_tag_get() may not be relied upon
unless radix_tree_tag_set/clear() and radix_tree_delete() are excluded from
running concurrently with it.
Reported-by: Romain DEGEZ <romain.degez@smartjog.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rwsems can be used with IRQs disabled, particularily in early boot
before IRQs are enabled. Currently the spin_unlock_irq() usage in the
slow-patch will unconditionally enable interrupts and cause problems
since interrupts are not yet initialized or enabled.
This patch uses save/restore versions of IRQ spinlocks in the slowpath
to ensure interrupts are not unintentionally disabled.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The log of commit edaac8e316 ("ratelimit:
Fix/allow use in atomic contexts"), indicates that we want to suppress the
callback when the trylock fails.
Signed-off-by: Yong Zhang <yong.zhang@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To prevent from wrongly using the return value.
[akpm@linux-foundation.org: fix spello]
Signed-off-by: Yong Zhang <yong.zhang@windriver.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Earlier in this function we set the last byte of "buf" to NULL so we
always hit the break statement and "i" is never equal to NAME_MAX_LEN.
This patch doesn't change how the driver works but it silences a Smatch
warning and it makes it clearer that we don't write past the end of the
array.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Add support for the hardware version of the Hamming weight function,
popcnt, present in CPUs which advertize it under CPUID, Function
0x0000_0001_ECX[23]. On CPUs which don't support it, we fallback to the
default lib/hweight.c sw versions.
A synthetic benchmark comparing popcnt with __sw_hweight64 showed almost
a 3x speedup on a F10h machine.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <20100318112015.GC11152@aftab>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Rename the extisting runtime hweight() implementations to
__arch_hweight(), rename the compile-time versions to __const_hweight()
and then have hweight() pick between them.
Suggested-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20100318111929.GB11152@aftab>
Acked-by: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <1265028224.24455.154.camel@laptop>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
This patch marks two functions, which only get called at
initialization, as __init.
Here is also interesting, that modpost doesn't catch here the right
function name.
WARNING: lib/built-in.o(.text+0x585f): Section mismatch in reference
from the function T.506() to the variable .init.data:obj
The function T.506() references the variable __initdata obj.
This is often because T.506 lacks a __initdata annotation or the
annotation of obj is wrong.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
LKML-Reference: <1269632315-19403-1-git-send-email-henne@nachtwindheim.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We see only one section mismatch now after thousands of randconfigs, and a
bug has been filed about that one.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
lcm() was defined to take integer-sized arguments. The supplied
arguments are multiplied, however, causing us to overflow given
sufficiently large input. That in turn led to incorrect optimal I/O
size reporting in some cases (RAID over RAID).
Switch lcm() over to unsigned long similar to gcd() and move the
function from blk-settings.c to lib.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
