Otherwise we may try to power down multiple times when the using
idle bias off and the driver is removed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The DCS_DATAPATH_BUSY bit used to monitor the completion of DC servo
operations has been deprecated and with some more recente revisions
may perform incorrectly, especially when only analogue bypass paths
are in use. Switch to using readback from the DC servo command
register instead, which is supported for all devices. Without this
unacceptably long timeouts may be observed in some circumstances.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
If we need to offset correct the DC servo then don't use runtime
recalibration since that is likely to introduce further offsets
which will be evident on powerdown.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
More recent Wolfson hubs devices add the ability to read back the DC
servo calibration information from the register used to write offsets,
and later still ones remove the old readback registers. Add support
for the new scheme, and use it for WM8994 device revisions that
support it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
If the correction wraps around then a substantial offset would be
introduced.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
With recent (2.6.34) chnages in PCM handling, capture stopped working on my
OMAP1510 based Amstrad Delta videophone.
Using 2.6.34-rc2, I was able to correct the problem in 3 different ways:
1. reverting commit 7b3a177b0d,
2. enabling additional jiffies check with
echo 4 >/proc/asound/card0/pcm0c0/xrun_debug
3. applying the patch below.
Since I wasn't able to reproduce the problem on my i686 PC, I guess the
problem is probably machine specific.
The patch reuses the method for software emulation of missing hardware
pointer, already implemented for playback on OMAP1510. It's possible that
event if a hardware pointer is available for capture on this machine, its
behaviour may be not compatible with what upper layer expects.
If you think the problem may be more general and should be solved differently,
on a higher level, I can try to work more on it if you give me a hint.
If the patch gets accepted, I suggest it goes as a fix in the current release
cycle.
Created and tested against linux-2.6.34-rc2.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
The way i've factored out the bus probe and removal functions so
that there's no code in the individual I2C and SPI functions means
that the register() and unregister() functions could just be squashed
into the bus_probe() and bus_remove() functions.
Signed-off-by: Barry Song <21cnbao@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
[The issue is an attempt to write the pdata without the AC97 device
allocated when using ac97.c - also added a comment in soc-core.c for the
special case for ac97. -- broonie]
Signed-off-by: Graham Gower <graham.gower@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Implicit slab.h inclusion via percpu.h is about to go away. Make sure
gfp.h or slab.h is included as necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Convert the device_terminate_all() operation on the
DMA engine to a generic device_control() operation
which can now optionally support also pausing and
resuming DMA on a certain channel. Implemented for the
COH 901 318 DMAC as an example.
[dan.j.williams@intel.com: update for timberdale]
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Maciej Sosnowski <maciej.sosnowski@intel.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Li Yang <leoli@freescale.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Magnus Damm <damm@opensource.se>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Joe Perches <joe@perches.com>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
ARM-SHMOBILE series have FIFO-buffered serial interface 2 (FSI2)
device which is advanced version of FSI.
This patch add simple support for it.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Sparse caught that initialize "playback" two times instead of
initializing "capture".
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Bit operation for fsi_master should be done inside master lock.
But soft-reset/interrupt operation were outside of it.
This patch modify this problem.
It still allow to INT_ST outside-operation on fsi_interrupt,
but it is not problem.
Because this register doesn't need the bit operation.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current ak4642 was not able to select pll.
This patch add support it.
It still expect PLL base input pin is MCKI.
see Table 5 "setting of PLL Mode" of datasheet
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This also adds the first DAI operation for AIF3 so fill out the ID and
the ops for that too.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Don't force enable the microphone bias on WM8903 when doing jack
detection, and don't force enable microphone bias. This allows
platforms to only enable microphone detection when a jack has been
inserted.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
If no report is specified then disable detection. Note that we don't
disable the slow clock, though the power consumption from it should
be negligable. That should be reference counted, ideally through DAPM.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Allow machines to control exactly when the bias is turned on and off.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Some systems, such as those with mechanical jack detection, may wish
to force enable a pin (typically mic bias) only some of the time.
Support such systems by having disable_pin() also coveer force enabled
pins.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Some systems provide both mechanical and electrical detection of jack
status changes. On such systems power savings can be achieved by only
enabling the electrical detection methods when physical insertion has
been detected.
Begin supporting such systems by providing a notifier for jack status
changes which can be used to trigger any reconfiguration.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Gain controls on outputs affect the power consumption
when the gain is set to non 0 value.
Outputs with amps have one register to configure the
routing and the gain:
PREDL_CTL (0x25):
bit 0: Voice enable
bit 1: Audio L1 enable
bit 2: Audio L2 enable
bit 3: Audio R2 enable
bit 4-5: Gain (0x0 - power down, 0x1 - 6dB, 0x2 - 0dB, 0x3 - -6dB)
bit 0 - 3: is handled in DAPM domain (DAPM_MIXER)
bit 4 - 5: has simple volume control
If there is no audio activity (BIAS_STANDBY), and
user changes the volume, than the output amplifier will
be enabled.
If the user changes the routing (but the codec remains in
BIAS_STANDBY), than the cached gain value also be written
to the register, which enables the amplifier.
The existing workaround for this is to have virtual
PGAs associated with the outputs, and whit DAPM PMD
the gain on the output will be forced to 0 (off) by
bypassing the regcache.
This failed to disable the amplifiers in several
scenario (as mentioned above).
Also if the codec is in BIAS_ON state, and user modifies
a volume control, which path is actually not enabled, than
that amplifier will be enabled as well, but it will
be not turned off, since there is no DAPM path, which
would make mute it.
To prevent amps being enabled, when they are not
needed, introduce the following workaround:
Track the state of each of this type of output.
In twl4030_write only allow actual write, when the
given output is enabled, otherwise only update
the reg_cache.
The PGA event handlers on power up will write the cached
value to the chip (restoring gain, routing selection).
On power down 0 is written to the register (disabling
the amp, and also just in case clearing the routing).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If instantiation of a card failed, we still have to remove it from the
card list on unregistration. This fixes an Oops on Migo-R, triggering,
when after a failed firmware load attempt the driver modules are removed
and re-inserted again.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This fixes a memory corruption when ASoC devices are used in
full-duplex mode. Specifically for pxa-ssp code, where this pointer
is dynamically allocated for each direction and destroyed upon each
stream start.
All other platforms are fixed blindly, I couldn't even compile-test
them. Sorry for any breakage I may have caused.
Reported-by: Sven Neumann <s.neumann@raumfeld.com>
Reported-by: Michael Hirsch <m.hirsch@raumfeld.com>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Note that since all the microphones share a bias there is a single
jack exported for all three, even though there are two physical
connectors plus the soldered down silicon mic. Note also that the SiMic
is always present by default.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Barry Song <21cnbao@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The export is not needed since the per-bus code lives in the same
module.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Yi Li <yi.li@analog.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Initial version of TWL6040 codec driver.
The TWL6040 codec uses a proprietary PDM-based digital audio interface.
Audio paths supported are:
- Input: Main Mic, Sub Mic, Headset Mic, Auxiliary-FM Left/Right
- Output: Headset Left/Right, Handsfree Left/Right
TWL6040 codec supports power-up/down manual and automatic sequence.
Manual sequence is done through a specific register writes sequence.
Automatic sequence is done when the codec is powered-up through the
external AUDPWRON line. The completion of the sequence is signaled
through the audio interrupt.
TWL6040 codec sysclk can be provided by: low-power or high
performance PLL:
- The low-power PLL takes a low-frequency input at 32,768 Hz and
generates an approximate of 17.64 or 19.2 MHz (for 44.1 KHz and 48 KHz
respectively)
- The high-performance PLL generates an exact 19.2 MHz clock signal
from high-frequency input at 12/19.2/26/38.4 MHz.
Low-power playback mode is a special scenario where only headset path
(headset DAC and driver) is active.
For the particular case of headset path, PLL being used defines the
headset power mode: low-power, high-performance.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We're keeping track of the number of times we've iterated but never
actually using this to bail out if the chip looks stuck.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
During validation of the internal clocking setup it has
been found that the following settings were not configured
in an optimal way:
ASRC_CTRL_A: SRCLKDIV was incorrect, instad of divide ratio 3,
ratio of 2 has to be used (as the comment stated)
DAC_CTRL_A: Fs = Fsref is the desired configuration instead of
Fs = Fsref / 1.5
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To make DSP_A mode working correctly the data delay should be
configured to 0. DSP_B mode thus can not be used with DAC33,
so remove it.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Basic support for Left Justified coding for OMAP McBSP.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Indentation in initial support for McPDM driver was converted to spaces.
Use tabs to comply with open source coding-style.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The SIU ASoC driver must load firmware to program the DSP, therefore it
has to select FW_LOADER in its Kconfig entry.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The registers for AD193X are defined as 0x800-0x810 for spi which uses
16_8 mode, for i2c to support AD1937, we will use 8_8 mode, only the low
byte of 0x800-0x810 is valid. The patch will not destory other codecs,
but make soc cache interface more useful.
Signed-off-by: Barry Song <barry.song@analog.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Barry Song <barry.song@analog.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8750 is using some delayed work to manage the ramping of the bias
at startup and resume out of line from the normal flow. This predates
the support within ASoC core for moving the resume out of line from the
main system resume which provides equivalent functionality with better
interaction with applications. Change to doing the ramp in line to make
use of the core functionality.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A code audit reveals that there are currently no users of the widget
controls on PGAs. This is likely to continue to be the case since
while there are useful things that can be done with integrating the
PGA gain and mute controls with the power sequencing userspace
generally wants stereo controls for output stages which this doesn't
map onto well.
In preparation for implementing something more useful strip out the
existing code, leaving the parameters there for use by the new code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8350 provides microphone presence and short circuit detection.
Integrate this with the ASoC jack reporting API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8904 allows microphone detection signals to be brought out as
alternate functions of the GPIO signals which can be detected using
interrupt inputs on the CPU. Allow this to be configured using
platform data.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Provide platform data allowing the configuration of the GPIO pins
on the WM8904 to be selected, allowing alternate functions to be
enabled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Support use of the WM8903 IRQ for reporting of microphone presence
and short detection.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Currently used to detect completion of the write sequencer.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Provide support for WM8903 microphone presence and short detection
using the GPIOs to route out a logic signal suitable for handling
using snd_soc_jack_add_gpios() on the processor GPIOs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Allow users to pass in a default configuration for the GPIOs of
the WM8903 as platform data. This allows configuration of the pin
muxing of the device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Allow pins to be forced on regardless of their power state. This is
intended for use with microphone bias supplies which need to be
enabled in order to support microphone detection - in systems without
appropriate hardware leaving the microphone unbiased when not in use
saves power.
The force done at power check time in order to avoid disrupting other
power detection logic.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (56 commits)
doc: fix typo in comment explaining rb_tree usage
Remove fs/ntfs/ChangeLog
doc: fix console doc typo
doc: cpuset: Update the cpuset flag file
Fix of spelling in arch/sparc/kernel/leon_kernel.c no longer needed
Remove drivers/parport/ChangeLog
Remove drivers/char/ChangeLog
doc: typo - Table 1-2 should refer to "status", not "statm"
tree-wide: fix typos "ass?o[sc]iac?te" -> "associate" in comments
No need to patch AMD-provided drivers/gpu/drm/radeon/atombios.h
devres/irq: Fix devm_irq_match comment
Remove reference to kthread_create_on_cpu
tree-wide: Assorted spelling fixes
tree-wide: fix 'lenght' typo in comments and code
drm/kms: fix spelling in error message
doc: capitalization and other minor fixes in pnp doc
devres: typo fix s/dev/devm/
Remove redundant trailing semicolons from macros
fix typo "definetly" -> "definitely" in comment
tree-wide: s/widht/width/g typo in comments
...
Fix trivial conflict in Documentation/laptops/00-INDEX
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (370 commits)
ARM: S3C2443: Add set_rate and round_rate calls for armdiv clock
ARM: S3C2443: Remove #if 0 for clk_mpll
ARM: S3C2443: Update notes on MPLLREF clock
ARM: S3C2443: Further clksrc-clk conversions
ARM: S3C2443: Change to using plat-samsung clksrc-clk implementation
USB: Fix s3c-hsotg build following Samsung platform header moves
ARM: S3C64XX: Reintroduce unconditional build of audio device
ARM: 5961/1: ux500: fix CLKRST addresses
ARM: 5977/1: arm: Enable backtrace printing on oops when PC is corrupted
ASoC: Fix S3C64xx IIS driver for Samsung header reorg
ARM: S3C2440: Fix plat-s3c24xx move of s3c2440/s3c2442 support
[ARM] pxa: fix typo in mxm8x10.h
[ARM] pxa/raumfeld: set GPIO drive bits for LED pins
[ARM] pxa/zeus: Add support for mcp2515 CAN bus
[ARM] pxa/zeus: Add support for onboard max6369 watchdog
[ARM] pxa/zeus: Add Eurotech as the manufacturer
[ARM] pxa/zeus: Correct the USB host initialisation flags
[ARM] pxa/zeus: Allow usage of 8250-compatible UART in uncompress
[ARM] pxa: refactor uncompress.h for non-PXA uarts
[ARM] mmp2: fix incorrect calling of chip->mask_ack() for 2nd level cascaded IRQs
...
Use the new delay calback function to report the delay through
ALSA for application caused by the internal FIFO.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Platform data option for the codec to keep the BCLK clock
continuously running in FIFO modes (codec master).
OMAP3 McBSP when in slave mode needs continuous BCLK running
on the serial bus in order to operate correctly.
Since in FIFO mode the DAC33 can also shut down the BCLK clock
and enable it only when it is needed, let the platforms decide
if the CPU side needs the BCLK running or not.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To avoid race condition especially in FIFO modes the
sequence for enabling and disabling the codec need to
be changed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The DM365 EVM has two codecs: the Audio Codec (AIC3x) and the Voice Codec,
the idea is to have both enabled in the same kernel simultaneously. However,
the current soc-core doesn't support simultaneous codecs, once that
support will have added, a patch will be posted to enable both codecs in
the DM365 EVM.
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently the DM365 is the only SoC that includes this Voice Codec.
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds the support for the interface needed by the DaVinci
Voice Codec CQ93VC.
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For ASoC, if either CPU or CODEC driver has set the flag, the MACHINE driver
should be given a chance to figure out if the dai, that set the flag, can
accomodate a rate that it does not explicitly specify but is specified
by the dai at the other end of the link.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver USE PLL for 11025/22050/44100/88200 rate.
To enable switching to bypass mode, PLL is always turned on.
Special thanks to Phil
Signed-off-by: Phil Edworthy <Phil.Edworthy@renesas.com>
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Towards having build for multiple SoCs segregate hw_params callback
for s3c2412 and s3c64xx.
Since, all new SoCs have s3c64xx like register map, we keep that as
default implementation if no SoC specific callback is already defined.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For some CPU-CODEC and source clock combination we might need to set
BCLK to N*Sample_size*LRCLK, where N may be even 3 or 4, not just 2.
We can simply remove the dependency of BCLK on sample size as there
is already a callback(S3C_I2SV2_DIV_BCLK) available to set required BCLK.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Towards generalizing CPU driver interface, do not accept direct field
values for the BCLK and RCLK.
The machine driver should simply request the FS-multiple and not provide
the value to be set in divide field of IISMOD.
[Confirmed by Jassi that no existing machine drivers are affected --
broonie]
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In order for the RATE and FMT defines to be reuseable in future by the
i2sv4 driver, move the MACROs out to the header file.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than having the multiple definitions of the same clocks,
define them in one common place and refer by SoC specific names.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
No point in duplicating this structure layout in each driver.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
On TI DM6467 EVM, S/PDIF DIT codec fails to open as it is unable to install
hardware params. This dummy codec has no set_fmt and set_sysclk implementations
and calls from the application to these functions cause errors. This patch adds
a new hardware params callback function for S/PDIF transciever codec.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Tested-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (26 commits)
ALSA: hdmi - show debug message on changing audio infoframe
ALSA: hdmi - merge common code for intelhdmi and nvhdmi
ALSA: hda - Add ASRock mobo to MSI blacklist
ALSA: hda: uninitialized variable fix
ALSA: hda: Use LPIB for a Biostar Microtech board
ALSA: usb/audio.h: Fix field order
ALSA: fix jazz16 compile (udelay)
ALSA: hda: Use LPIB for Dell Latitude 131L
ALSA: hda - Build hda_eld into snd-hda-codec module
ALSA: hda - Support NVIDIA MCP89 and GT21x hdmi audio
ALSA: hda - Support max codecs to 8 for nvidia hda controller
ALSA: riptide: clean up while loop
ALSA: usbaudio - remove debug "SAMPLE BYTES" printk line
ALSA: timer - pass real event in snd_timer_notify1() to instance callback
ALSA: oxygen: change || to &&
ALSA: opti92x: use PnP data to select Master Control port
ASoC: fix ak4104 register array access
ASoC: soc_pcm_open: Add missing bailout tag
ALSA: usbaudio: Fix wrong bitrate for Creative Creative VF0470 Live Cam
ALSA: ua101: removing debugging code
...
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (26 commits)
sh: Convert sh to use read/update_persistent_clock
sh: Move PMB debugfs entry initialization to later stage
sh: Fix up flush_cache_vmap() on SMP.
sh: fix up MMU reset with variable PMB mapping sizes.
sh: establish PMB mappings for NUMA nodes.
sh: check for existing mappings for bolted PMB entries.
sh: fixed virt/phys mapping helpers for PMB.
sh: make pmb iomapping configurable.
sh: reworked dynamic PMB mapping.
sh: Fix up cpumask_of_pcibus() for the NUMA build.
serial: sh-sci: Tidy up build warnings.
sh: Fix up ctrl_read/write stragglers in migor setup.
serial: sh-sci: Add DMA support.
dmaengine: shdma: extend .device_terminate_all() to record partial transfer
sh: merge sh7722 and sh7724 DMA register definitions
sh: activate runtime PM for dmaengine on sh7722 and sh7724
dmaengine: shdma: add runtime PM support.
dmaengine: shdma: separate DMA headers.
dmaengine: shdma: convert to platform device resources
dmaengine: shdma: fix DMA error handling.
...
The headphone detect and charger are using the IRQ numbers so need
to take account of irq_base with the genirq conversion. I obviously
picked the wrong system for initial testing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Rename for_each_bit to for_each_set_bit in the kernel source tree. To
permit for_each_clear_bit(), should that ever be added.
The patch includes a macro to map the old for_each_bit() onto the new
for_each_set_bit(). This is a (very) temporary thing to ease the migration.
[akpm@linux-foundation.org: add temporary for_each_bit()]
Suggested-by: Alexey Dobriyan <adobriyan@gmail.com>
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Artem Bityutskiy <dedekind@infradead.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently during pop/click debug we're inserting a delay both after
every log message we generate and at explicit points in the sequence,
slowing things down even further than they need to be especially when
many writes get coalesced by the sequence generation code.
Remove the per-printk delay and ensure that we have explicit delays
where we say we want them.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The reorgs of the Samsung headers have moved the GPIO bank definitions
from plat/ to mach/ - the IIS driver needs to be updated to take care
of this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Report the current FIFO depth when delay is queried. The FIFO is only
16 frames deep so the latency will be at most a couple of miliseconds
(and we tend to end up reporting zero most of the time) but it may
help some applications.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Don't touch the variable 'reg' to construct the value for the actual SPI
transport. This variable is again used to access the driver's register
cache, and so random memory is overwritten.
Compute the value in-place instead.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: stable@kernel.org
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The codec_dai needs to be shutdown should the machine startup fails.
This patch adds another bailout tag for that case and rename the tag
for configuration failures.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8960 headphone outputs can be run in capless mode with OUT3
used to drive a pseudo ground for the headphone drivers. In this
mode the mono mixer is not used, the mixer should be turned on
in concert with the headphone output drivers and the device bias
levels are managed differently.
Also tweak the existing bias management to remove the use of active
discharge while we're at it since that's often audible.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Avoids machine files having to peer into sound/soc which is a bit
rude and icky.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The driver name gets used by dev_() logging so use something a bit
more idiomatic.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The delay callback can be used by the core to query the delay
on the dai caused by FIFO or delay in the platform side.
In case if both CPU and CODEC dai has FIFO the delay reported
by each will be added to form the full delay on the chain.
If none of the dai has FIFO, than the delay will be kept as
zero.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Create a soc level wrapper for pcm_pointer callback.
This will facilitate the soc level handling of different
HW buffers in the audio path.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
My editor removes the tailing spaces, which causes problems when
changing the soc-core.c
Removing the space.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Initial support for audio using the 1133-EV1 audio and PMIC module for
the i.MX31ADS. Currently only playback is supported, and the FIQ DMA
driver has performance problems at higher sample rates which cause
audible dropouts.
This driver is based heavily on an out of tree one written by Liam
Girdwood.
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Separate SH DMA headers into ones, commonly used by both drivers, and ones,
specific to each of them. This will make the future development of the
dmaengine driver easier.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (252 commits)
ASoC: Check progress when reporting periods from i.MX FIQ handler
ASoC: Remove a unused variables from i.MX FIQ runtime data
ALSA: hda - Add/fix ALC269 FSC and Quanta models
ALSA: hda - Add ALC670 codec support
OMAP4: PMIC: Add support for twl6030 codec
ALSA: hda - remove unnecessary msleep on power state transitions
usb/gadget/{f_audio,gmidi}.c: follow recent changes in audio.h
ASoC: fsi: Modify over/under run error settlement
ASoC: OMAP4: Add McPDM platform driver
ASoC: OMAP4: Add support for McPDM
ASoC: OMAP: data_type and sync_mode configurable in audio dma
ALSA: hda - Add missing description in HD-Audio-Models.txt
ALSA: add support for Macbook Air 2,1 internal speaker
ALSA: usbaudio: consolidate header files
ALSA: usbmixer: bail out early when parsing audio class v2 descriptors
ALSA: usbaudio: implement basic set of class v2.0 parser
ALSA: usbaudio: introduce new types for audio class v2
ALSA: usbaudio: parse USB descriptors with structs
ALSA: hda - enable snoop for Intel Cougar Point
ALSA: hda - Remove identical definitions for macmini3 model
...
Machine driver for DB1200 AC97 and I2S audio systems, intended as a proper
reference asoc machine for Alchemy-based systems. AC97/I2S can be selected
at boot time by setting switch S6.7.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Cc: alsa-devel@alsa-project.org
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
DMA can only be done from physical addresses; move the "virt_to_phys"
source/destination buffer address translation from the dbdma queueing
functions (since the hardware can only DMA to/from physical addresses)
to their respective users.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove dbdma compat macros, move remaining users over to default
queueing functions and -flags.
(Queueing function signature has changed in order to give
a build failure instead of silent functional changes due
to the no longer implicitly specified DDMA_FLAGS_IE flag)
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If we are to have a snd_soc_dai i.e, cpu_dai and codec_dai, shared among two
or more dai_links we need to log the number of active users of the dai.
For that, we change semantics of the snd_soc_dai.active flag from indicator
to reference counter.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6: (41 commits)
of: remove undefined request_OF_resource & release_OF_resource
of/sparc: Remove sparc-local declaration of allnodes and devtree_lock
of: move definition of of_chosen into common code.
of: remove unused extern reference to devtree_lock
of: put default string compare and #a/s-cell values into common header
of/flattree: Don't assume HAVE_LMB
of: protect linux/of.h with CONFIG_OF
proc_devtree: fix THIS_MODULE without module.h
of: Remove old and misplaced function declarations
of/flattree: Make the kernel accept ePAPR style phandle information
of/flattree: endian-convert members of boot_param_header
of: assume big-endian properties, adding conversions where necessary
of: use __be32 for cell value accessors
of/flattree: use OF_ROOT_NODE_{SIZE,ADDR}_CELLS DEFAULT for fdt parsing
of/flattree: use callback to setup initrd from /chosen
proc_devtree: include linux/of.h
of: make set_node_proc_entry private to proc_devtree.c
of: include linux/proc_fs.h
of/flattree: merge early_init_dt_scan_memory() common code
of: add 'of_' prefix to machine_is_compatible()
...
Currently the i.MX FIQ handler is reporting periods as elapsed based
purely on a timer running in the CPU. This means that any clock
mismatch between the CPU and the audio subsystem can result in the
status reported to applications drifting away from the actual status
of the hardware. This is particularly likely at present since the
SSI driver is only capable of operating in slave mode so it's very
likely that the interface will be clocked from a different source.
Instead check the offset reported by the FIQ and only notify when we
have transferred at least one period, re-firing the timer if we didn't
do so. Also factor out the calculation of the timer expiry time for
make it a bit easier to experiment with.
Note that this only improves the situation, problems can still be
triggered.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Add ASoC interface for OMAP McBSP2 and McBSP3 sidetones.
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In current FSI driver, playback function cares only overrun,
and capture function cares only underrun.
But playback function should had cared about underrun,
and capture function should had cared about overrun too.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
McPDM platform driver is configured to use sDMA in order to transfer
to/from memory. Support for interfacing with ABE will be added later.
McPDM dai currently supports up to 4 downlink channels and 2 uplink
channels simultaneously, as well as 88.2 and 96 KHz, and a sample
size of 32 bits.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Signed-off-by: Margarita Olaya <x0080101@ti.com>
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
McPDM is the interface between Phoenix audio codec
and the OMAP4430 processor. It enables data to be transfered
to/from Phoenix at sample rates of 88.4 or 96 KHz.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Margarita Olaya <x0080101@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow client drivers to set the data_type (16, 32) and the
sync_mode (element, packet, etc) of the audio dma transferences.
McBSP dai driver configures it for a data type of 16 bits and
element sync mode.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Check the card->codec on soc_resume to detect if the soc
device is properly initialized.
If the card->codec is NULL, than do not continue the resume
operation, since the device is not initialized properly.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In order for having snd_soc_dais shared among two or more dai_links,
remove the relatively global runtime field from the struct snd_soc_dai
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently only the atmel driver make use of snd_soc_dai.runtime field.
If the dais are to be shared among two or more dai_links, the field
must be got rid of.
So, in atmel driver reach the substream via dai_link->pcm so as to
not depend of snd_soc_dai.runtime field.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Passing pointer to relevant dai_link provides easier reach to the
ASoC tree in suspend/resume of snd_soc_platform. It also provides
direct access to the dai at the other end of the dai_link.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Disable the amplifiers for the headset outputs, and do not select
routings by default to the headset outputs.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
OSCSET calculation was not correct in case of 44.1KHz
sampling rate.
With small adjustment both 48 and 44.1 KHz calculation
now gives the correct value.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In repeated playback the FIFOFLUSH bit remained set, and
never has been cleared.
Clear it during the setup phase.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Provide a sysfs file allowing userspace to inspect and change the
pmdown_time setting at runtime.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Make the pmdown_time a per-card setting rather than a global one,
initialised before the card initialisation runs. This allows cards
to override the default setting if it makes sense to do so (for
example, due to an unavoidable pop).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM2000 is a low power, high quality handset receiver speaker
driver with Wolfson myZone™ Ambient Noise Cancellation (ANC). It
provides enhanced voice communication quality in a noisy environment
if the handset acoustics are designed appropriately.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Audio on Migo-R cannot work if CONFIG_SH_DMA_API=y, but compilation should not
break anyway.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch expands the omap3beagle sound soc for the
beagle board clone DevKit8000.
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The serial interface (TDM/I2S) for the audio block have been
constantly enabled.
Introduce a new DAPM_SUPPLY for handling the AIF_EN bit, so
the interface is only enabled, when there is a need for it.
For example when only the analog loopback is enabled, there
is no need to keep the serial interface active.
I have added the persons who contributed to the Voice path
of twl4030 codec driver, so they might have the ability
to test this patch, and send an update for the Voice path,
if it is necessary
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Enable the bulk regulators at probe time so we can safely disable them
again when going to suspend without confusing the reference counter.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds sound support for Phytec PhyCORE / PhyCARD
modules in AC97 mode.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
machine is compatible is an OF-specific call. It should have
the of_ prefix to protect the global namespace.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Michal Simek <monstr@monstr.eu>
In particular, several occurances of funny versions of 'success',
'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address',
'beginning', 'desirable', 'separate' and 'necessary' are fixed.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pandora's external DAC is connected to VSIM TWL4030 supply, so let's
start switching it too to save more power.
Also DAC got it's own DAPM handler.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pandora's external DAC is using 256*Fs output from the TWL4030
codec, and TWL4030 needs to have APLL enabled for it's 256*Fs
output to function.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The module unloading path had several problems:
- it freed up the private structure twice
- it freed up the codec structure, which was allocated as part
of the private structure
- it did not freed up the reg_cache
- it did not unregistered the dais and the codec
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8912 is a DAC only device register compatible with the WM8904
CODEC with ADC portions omitted. Support it within the WM8904 driver
based on the configured I2C device name.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Handle the output PGAs as part of the output powerup since they can
never be powered separately and reorder things so that we remove the
output shorts after both line and headphone outputs have been brought
up, minimising the opportunity for any issues.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
As well as disabling the biases of the CODEC the drop into BIAS_OFF will
also disable all the regulators powering the CODEC, allowing even greater
power savings on appropriately configured systems.
Since the regulator API does not currently provide notification when
regulators are disabled we assume that this always happens when we stop
using the regulators. Once 2.6.34 is merged this code can be optimised
to only sync the cache when power was actually removed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
While the regulators are disabled we cache all register writes.
Currently we assume that the regulator disable actually takes
effect, after the merge with the regulator tree in 2.6.34 the
regulator API will be able to notify us if the power is actually
removed (due to constraints or regulator sharing it may not be).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
At the minute the regulators are simply enabled for the entire
lifetime of the device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Add a bit to the CODEC structure indicating if a cache sync is required.
By default this will be set if a cache only write is done to a soc-cache
register cache. This allows us to avoid syncing the cache back after
using cache only writes if there were no changes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Currently the soc-cache code will always write to the device, meaning
that we need the device to be powered and active at pretty much all
times the system is active. Allowing cache only writes lays some
groundwork for future enhancements to allow devices to be put into a
full off state when the audio subsystem is idle.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
ctrl_outl() has become void at some point, which breaks compilation of fsi.c.
Make writing functions void, as their output is anyway not evaluated, and use
__raw_writel and __raw_readl instead of deprecated ctrl_outl and ctrl_inl
respectively.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Unconditionally save the register states when suspending and restore
them again at resume time. Register contents were not preserved over
suspend, and hence the driver takes false assumptions about them.
The clock must be enabled to access the register block.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
String constants that are continued on subsequent lines with \
are not good.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The dependency on MFD_WM8994 rather than I2C went awry.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8994 is a highly integrated ultra-low power hi-fi audio subsystem
designed for smartphones and other portable devices rich in multimedia
features. It provides advanced digital mixing facilities enabling low
power high quality interconnection of CPU, baseband and other audio
sources through flexible digital and analogue routing, and integrates
a class W headphone driver and stereo class D speaker drivers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use a two code correction for optimal performance.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Perform DC servo offset calibration using a series update sequence
rather than startup update sequence, tuning the configuration of the
WM8993 DC servo to make best use of this.
Also introduce currently unused data allowing us to correct for
any systematic errors in the DC servo calibration results and an
alternative startup path for the headphone output which performs
better with some chip revisions. The alternative setup sequence is
enabled for WM8993.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
String constants that are continued on subsequent lines with \
are not good.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In case, if OPCLK is not used, and PLL is used for driving the codec, the
choice of PLL output frequency could result in a needlessly imprecise
system clock frequency. Use an iterative process to select a precise
configuration.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
wm8974 and wm8978 codec drivers control DAC and ADC oversampling rates in their
.set_clkdiv() methods, which is wrong, because these are simple boolean
switches and not clock dividers. Move these bits to sound controls. Also remove
manual configuration of the MCLK divider in wm8978, since it is configured
automatically.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tests showed, that bit 6 of the WM8978_POWER_MANAGEMENT_2 register of wm8978
affects codec clocks. Being useless for suspend / resume, it cannot be used in
bias-level control either. Remove this bit handling.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add support for audio on sh7722-based Migo-R boards, using SIU and wm8978
codec, recording via external microphone and playback via headphones are
implemented.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It's more robust when references are provided in control names
rather than numid.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 761c9d45 (ASoC: Fix build of OMAP sound drivers) changes
CONFIG_MACH_OMAP3517EVM -> CONFIG_SND_OMAP_SOC_OMAP3517EVM in the
Makefile. Whereas the config option defined in Kconfig is
SND_OMAP_SOC_AM3517EVM. Because of this, ASoC driver for AM3517
was not getting compiled.
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit e9ff5eb2 (Fixing infinite loop in resume path) uses wrong AIC23
register in resume function because of which register writes happen
on some non-existing registers.
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Also renames a few things to make volumes and switches match up in
alsamixer.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The version isn't being updated or used, the kernel revision
tracking is enough.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Change the legacy default register configuration, which left some
internal components on.
Now we have either DAPM, or other ways to control these bits,
so there is no need to enable them by default.
The affected parts:
Disable ADCL and ADCR
Disable ARXL2 and ARXR2 analog PGA (playback)
Disable APLL by default
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
fsi_master_xxx function should be protected by spin lock,
because it are used from both FSI-A and FSI-B.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8978 codec from Wolfson Microelectronics is very similar to
wm8974, but is stereo and also has some differences in pin configuration
and internal signal routing. This driver is based on wm8974 and takes
the differences into account.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The board supports both GPIO sets for the AC97 bus and the analogue
outputs can be switched between this and the WM8580 so add some
comments saying what the setup the standard kernel expects is.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since, we have generic AC97 controller driver and all the machines
have moved to that, there is no need for old s3c2443-ac97.c to exist.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Switch to use s3c-ac97.c AC97 controller driver.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Switch to use s3c-ac97.c AC97 controller driver.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds the common machine driver for SMDKs that
have a WM9713 codec attched to the AC97 controller.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add the AC97 controller driver for Samsung SoCs that have one.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Barry Song <Barry.Song@analog.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Barry Song <Barry.Song@analog.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Sometimes after a suspend-resume cycle, the ALSA application
restarts the stream when resume fails and McASP fails to work
as the clock is not enabled. This patch corrects this bug.
Testes on TI DA850/OMAP-L138 EVM.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
tests show frequent suspend/resume(frequent poweroff/on ad1836 internal
components) maybe make ad1836 clock mode wrong sometimes after wakeup.
This patch reset/restore ad1836 clock mode while executing PM, then
ad1836 can always resume to right clock status.
Signed-off-by: Barry Song <21cnbao@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Several SuperH platforms, including sh7722, sh7343, sh7354, sh7367 include
a Sound Interface Unit (SIU). This patch adds DAI and platform / DMA
drivers for this interface.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remember to free the temporary register-cache.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
This provides a small power saving when audio is inactive.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Currently ASoC always maintains the bias of the CODEC while the system
is active. With older mobile CODECs this is required since the outputs
are referenced to a non-zero voltage and enabling or disabling this
voltage without audible pops or clicks in the output takes too long to
do when starting or stopping audio.
As a result of features such as ground referenced outputs and class D
speaker drivers current generation devices are able to power on and off
much more quickly without these system level issues so provide a new
flag idle_bias_off in snd_soc_codec which will cause the core to turn
off the CODEC bias. The distinction between STANDBY and OFF is still
maintained. This is partly for consistency but also allows for
potential future extensions such as per-machine overrides or deferring
the bias removal.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The same information is now visible via debugfs and with large modern
devices dumping everything to the console can be very resource
intensive, causing more harm than good.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Add possibility to configure the burst mode BCLK divider through platform
data structure.
The BCLK divider changes the actual speed of the serial bus in burst mode,
which is faster than the sampling frequency of the running stream.
In this way platforms can experiment with the optimal burst speed without
the need to modify the codec driver itself.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The BCLK divider was not configured in case of mode7.
This leads to unpredictable behavior when switching between FIFO modes.
Configure the BCLK divider depending on the fifo_mode (FIFO is in use,
or FIFO bypass).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Set the prefill number of samples as the same as the lower
threshold in mode7.
In this way the codec will read the same amount of data on
startup and during the running playback.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
