Both old-IDE and libata should be able handle all controllers and
devices found using normal resource reservation methods.
This eliminates the awful, low-performing split-driver configuration
where old-IDE drove the PATA portion of a PCI device, in PIO-only mode,
and libata drove the SATA portion of the /same/ PCI device, in DMA mode.
Typically vendors would ship SATA hard drive / PATA optical
configuration, which would lend itself to slow (PIO-only) CD-ROM
performance.
For Intel users running in combined mode, it is now wholly dependent on
your driver choice (potentially link order, if you compile both drivers
in) whether old-IDE or libata will drive your hardware.
In either case, you will get full performance from both SATA and PATA
ports now, without having to pass a kernel command line parameter.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With Tejun having added adev->ap some time ago we can get rid of the
almost unused port being passed to mode filters. And while we are
doing filters, lets turn on the !IORDY filter as well.
Signed-off-by: Alan Cox <alan@redhat.com>
With some hand massaging from
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_port has two different id fields - id and port_no. id is
system-wide 1-based unique id for the port while port_no is 0-based
host-wide port number. The former is primarily used to identify the
ATA port to the user in printk messages while the latter is used in
various places in libata core and LLDs to index the port inside the
host.
The two fields feel quite similar and sometimes ap->id is used in
place of ap->port_no, which is very difficult to spot. This patch
renames ap->id to ap->print_id to reduce the possibility of such bugs.
Some printk messages are adjusted such that id string (ata%u[.%u])
isn't printed twice and/or to use ata_*_printk() instead of hardcoded
id format.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch is against the libata core and headers.
Two IRQ calls are added in ata_port_operations.
- irq_on() is used to enable interrupts.
- irq_ack() is used to acknowledge a device interrupt.
In most drivers, ata_irq_on() and ata_irq_ack() are used for
irq_on and irq_ack respectively.
In some drivers (ex: ahci, sata_sil24) which cannot use them
as is, ata_dummy_irq_on() and ata_dummy_irq_ack() are used.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert libata core layer and LLDs to use iomap.
* managed iomap is used. Pointer to pcim_iomap_table() is cached at
host->iomap and used through out LLDs. This basically replaces
host->mmio_base.
* if possible, pcim_iomap_regions() is used
Most iomap operation conversions are taken from Jeff Garzik
<jgarzik@pobox.com>'s iomap branch.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update libata core layer to use devres.
* ata_device_add() acquires all resources in managed mode.
* ata_host is allocated as devres associated with ata_host_release.
* Port attached status is handled as devres associated with
ata_host_attach_release().
* Initialization failure and host removal is handedl by releasing
devres group.
* Except for ata_scsi_release() removal, LLD interface remains the
same. Some functions use hacky is_managed test to support both
managed and unmanaged devices. These will go away once all LLDs are
updated to use devres.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
An ATA controller in native mode may have one or more channels disabled
and not assigned resources. In that case the existing code crashes trying
to access I/O ports 0-7.
Add the neccessary check.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On the Maple board, the AMD8111 IDE is in legacy mode... except that it
appears on IRQ 20 instead of IRQ 15. For drivers/ide this was handled by
the architecture's "pci_get_legacy_ide_irq()" function, but in libata we
just hard-code the numbers 14 and 15.
This patch provides asm-powerpc/libata-portmap.h which maps the IRQ as
appropriate, having added a pci_dev argument to the
ATA_{PRIM,SECOND}ARY_IRQ macros.
There's probably a better way to do this -- especially if we observe
that the _only_ case in which this seemingly-generic
"pci_get_legacy_ide_irq()" function returns anything other than 14 and
15 for primary and secondary respectively is the case of the AMD8111 on
the Maple board -- couldn't we handle that with a special case in the
pata_amd driver, or perhaps with a PCI quirk for Maple to switch it into
native mode during early boot and assign resources properly?
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fixes bogus accesses to ports 0-15 with a non DMA capable controller.
This I think should go in for 2.6.20
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some uli controllers have stuck SIMPLEX bit which can't be cleared
with ata_pci_clear_simplex(), but the controller is capable of doing
DMAs on both channels simultaneously. Implement ATA_FLAG_IGN_SIMPLEX
which makes libata ignore the simplex bit and use it in sata_uli.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a slight variant on the patch I posted December 16th to fix
libata combined mode handling. The only real change is that we now
correctly also reserve BAR1,2,4. That is basically a neatness issue.
Jeff was unhappy about two things
1. That it didn't work in the case of one channel native one channel
legacy.
This is a silly complaint because the SFF layer in libata doesn't handle
this case yet anyway.
2. The case where combined mode is in use and IDE=n.
In this case the libata quirk code reserves the resources in question
correctly already.
Once the combined mode stuff is redone properly (2.6.21) then the entire
mess turns into a single pci_request_regions() for all cases and all the
ugly resource hackery goes away.
I'm sending this now rather than after running full test suites so that
it can get the maximal testing in a short time. I'll be running tests on
this after lunch.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Acked-by: Alessandro Suardi <alessandro.suardi@gmail.com>
Acked-by: Theodore Tso <tytso@mit.edu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that BMDMA status is recorded in irq handler. ata_bmdma_freeze()
is free to manipulate host status. Under certain circumstances, some
controllers (ICH7 in enhanced mode w/ IRQ shared) raise IRQ when CTL
register is written to and ATA_NIEN doesn't mask it.
This patch makes ata_bmdma_freeze() clear all pending IRQs after
freezing a port. This change makes explicit clearing in
ata_device_add() unnecessary and thus kills it. The removed code was
SFF-specific and was in the wrong place.
Note that ->freeze() handler is always called under ap->lock held and
irq disabled. Even if CTL manipulation causes stuck IRQ, it's cleared
immediately. This should be safe (enough) even in SMP environment.
More correct solution is to mask the IRQ from IRQ controller but that
would be an overkill.
Signed-off-by: Tejun Heo <htejun@gmail.com>
For certain errors, interrupt handler alter BMDMA host status before
entering EH (clears active and intr). Thus altered BMDMA host status
value is recorded by BMDMA EH and reported to user. Move BMDMA host
status recording from EH to interrupt handler.
Signed-off-by: Tejun Heo <htejun@gmail.com>
There are machines out there which share legacy PCI IDE IRQs w/ other
devices. libata SFF interrupt/HSM code is ready for shared IRQ and
has been setting IRQF_SHARED for devices in native PCI mode. Device
in legacy mode is still a PCI device and thus supposedly uses
active-low level triggered IRQ.
Machines with such setup should be quite rare and w/o this flag libata
is likely to fail loading and render the system unuseable. Also, IDE
driver has been setting IRQF_SHARED for devices in legacy mode for a
looooong time.
Signed-off-by: Tejun Heo <htejun@gmail.com>
ata_irq_on() isn't used outside of libata core layer. The function is
TF/SFF interface specific but currently used by core path with some
hack too. Move it from include/linux/libata.h to
drivers/ata/libata-sff.c.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds support for ADMA mode on NVIDIA nForce4 (CK804/MCP04) SATA
controllers to the sata_nv driver. Benefits of ADMA mode include:
- NCQ support
- Reduced CPU overhead (controller DMAs command information from memory
instead of them being pushed in by the CPU)
- Full 64-bit DMA support
ADMA mode is enabled by default in this version. To disable it, set the
module parameter adma_enabled=0.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There are some Linux supported platforms that simply cannot hit the low
I/O addresses used by ATA legacy mode PCI mappings. These platforms have
a window for PCI space that is fixed by the board logic and doesn't
include the neccessary locations.
Provide a config option so that such platforms faced with a controller
that they cannot support simply error it and punt
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Don't write the same code twice, in two different functions, when they
both call the same initialization function, with the same private_data
pointer info.
Also, note a bug found with a FIXME.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* Replace needless 'n_ports > 2' check with a simple BUG_ON().
No existing driver ever wants more than 2 ports.
* Delete ATA_FLAG_NO_LEGACY check. No current driver uses
ata_pci_init_one(), that sets this flag.
* Move PCI_CLASS_PROG register read below pci_enable_device()
* Handle ata_device_add() failure
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Non-uniform ports handling got broken while updating libata to handle
those in the same host. Only separate irq for the non-uniform
secondary port was implemented while all other fields (host flags,
transfer mode...) of the secondary port simply shared those of the
first.
For ata_piix combined mode, which ATM is the only user of non-uniform
ports, this causes the secondary port assume the wrong type. This can
cause PATA port to use SATA ops, which results in bogus check on PCS
and detection failure.
This patch adds ata_probe_ent->pinfo2 which points to optional
port_info for the secondary port. For the time being, this seems to
be the simplest solution. This workaround will be removed together
with ata_probe_ent itself after init model is updated to allow more
flexibility.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Nelson A. de Oliveira <naoliv@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
