When using new Multi-function modes it's possible that due to incompatible
configuration management FW will fallback into an existing mode.
Notice that at the moment this fallback is exactly the same as the already
existing switch-independent multi-function mode, but we still use existing
infrastructure to hold this information [in case some small differences will
arise in the future].
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for a new multi-function mode based on the Unified Fabric Port
system specifications.
Support includes configuration of:
1. Outer vlan tags.
2. Bandwidth settings.
3. Virtual link enable/disable.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rearrange macros to query for storage-only modes in different MF environment.
Improves the readibility and maintainability of the code. E.g.:
- if (IS_MF_STORAGE_SD(bp) || IS_MF_FCOE_AFEX(bp))
+ if (IS_MF_STORAGE_ONLY(bp))
In addition, this removes the need for bnx2x_is_valid_ether_addr().
Signed-off-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The integrated BCM7xxx PHY contains no useful revision information in
its MII_PHYSID2 bits 3:0, that information is instead contained in the
GENET hardware block.
We already read the GENET 32-bit revision register, so store the
integrated PHY revision in the driver private structure, and then
communicate this revision value to the PHY driver by overriding the
phy_flags value.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have removed the need for the PHY_BRCM_100MBPS_WAR flag, we
can remove it from the GENET driver and the broadcom shared header file.
The PHY driver checks the PHY supported bitmask instead.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enable three queues on imx6sx enet, and then do tx performance
test with iperf tool, after some time running, tx hang.
Found that:
If uDMA is running, software set TDAR may cause tx hang.
If uDMA is in idle, software set TDAR don't cause tx hang.
There is a TDAR race condition for mutliQ when the software sets TDAR
and the UDMA clears TDAR simultaneously or in a small window (2-4 cycles).
This will cause the udma_tx and udma_tx_arbiter state machines to hang.
The issue exist at i.MX6SX enet IP.
So, the Workaround is checking TDAR status four time, if TDAR cleared by
hardware and then write TDAR, otherwise don't set TDAR.
The patch is only one Workaround for the issue ERR007885.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when enable interrupt coalesce, 8 BD is not enough.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i.MX6 SX support interrupt coalescence feature
By default, init the interrupt coalescing frame count threshold and
timer threshold.
Supply the ethtool interfaces as below for user tuning to improve
enet performance:
rx_max_coalesced_frames
rx_coalesce_usecs
tx_max_coalesced_frames
tx_coalesce_usecs
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
check tx and rx queue seperately.
fix typo, "Invalidate" and "fail".
change pr_err to pr_warn.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replacing strncpy with strlcpy to avoid strings that lacks null terminate.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replacing strncpy with strlcpy to avoid strings that lacks null terminate.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use container_of instead of casting first structure member.
Compiled but untested.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use container_of instead of casting first structure member.
ARM cross-compiled but untested.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print the IP revision when probing.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i.MX6 SX change FEC alignment requirement.
i.MX6 SX change internal bus from AHB to AXI.
It require RX buffer must be 64 bytes alignment.
And remove TX buffer alignment requirement.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add compatible string "fsl,imx6sx-fec" for i.MX6SX.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i.MX6SX Enet-AVB support 3 tx queues, 3 rx queues.
For tx queues: ring 0 -> best effort
ring 1 -> Class A
ring 2 -> Class B
For rx queues:
ring 0 -> best effort
ring 1 -> receive VLAN packet with classification match
ring 2 -> receive VLAN packet with classification match
Add enet-avb IP multiqueue support for the driver.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For i.MX6SX enet use AXI bus, reset MAC will make system bus dead
if ENET-AXI bus has pending access (AHB bus should not have such issue).
So, disable enet with AVB MAC instead of reset MAC itself.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
initilized all queues according to queue number get from DT file.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Duan Fugang <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, the tx/rx queue number is 1, user can config the queue number
at DTS file like this:
fsl,num-tx-queues=<3>;
fsl,num-rx-queues=<3>
Since i.MX6SX enet-AVB IP support multi queues, so use multi queues
interface to allocate and set up an Ethernet device.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch just change data structure to support multi-queue.
Only 1 queue enabled.
Ethernet multiqueue mechanism can improve performance in SMP system.
For single hw queue, multiqueue can balance cpu loading.
For multi hw queues, multiple cores can process network packets in parallel,
and refer the article for the detail advantage for multiqueue:
http://vger.kernel.org/~davem/davem_nyc09.pdf
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <frank.li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add enet AVB feature macro define for imx6sx.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i.MX6sx enet has below clocks for user config:
clk_ipg: ipg_clk_s, ipg_clk_mac0_s, 66Mhz
clk_ahb: enet system clock, it is enet AXI clock for imx6sx.
For imx6sx, it alos is the clock source of interrupt coalescing.
The clock range: 200Mhz ~ 266Mhz.
clk_ref: refrence clock for tx and rx. For imx6sx enet RGMII mode,
the refrence clock is 125Mhz coming from internal PLL or external.
In i.MX6sx-arm2 board, the clock is from internal PLL.
clk_ref is optional, depends on board.
clk_enet_out: The clock can be output from internal PLL. It can supply 50Mhz
clock for phy. clk_enet_out is optional, depends on chip and board.
clk_ptp: 1588 ts clock. It is optional, depends on chip.
The patch add clk_ref to distiguish the different clocks.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently PCIe error reporting is enabled only on PFs. This patch enables
this feature on VFs too as Lancer VFs support it.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MODIFY_EQ_DELAY FW cmd on Lancer is supported for a max of 8 EQs per cmd.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report the ethtool port-type/supported/advertising values based on the
cable_type for QSFP and SFP+ interfaces. The cable_type is parsed from
the transceiver data fetched from the FW.
Signed-off-by: Ravikumar Nelavelli <ravikumar.nelavelli@emulex.com>
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the dump-module-eeprom and module-info
ethtool options.
Signed-off-by: Mark Leonard <mark.leonard@emulex.com>
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some configurations the FW doesn't allow changing flow control settings
of a link. Unless a v1 version of the SET_FLOW_CONTROL cmd is used, the FW
doesn't report an error to the driver.
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the RX path, the driver currently consumes upto 64 (budget) packets in
one NAPI sweep. When the size of the packet received is larger than a
fragment size (2K), more than one fragment is consumed for each packet.
As the driver currently posts a max of 64 fragments, all the consumed
fragments may not be replenished. This can cause avoidable drops in RX path.
This patch fixes this by posting a max(consumed_frags, 64) frags. This is
done only when there are atleast 64 free slots in the RXQ.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace strcpy with strlcpy, as it avoids a possible buffer overflow.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following minor issues with log messages in be2net:
1) Period is not required at the end of log message.
2) Remove "Unknown grp5 event" logs to reduce noise. The driver can safely
ignore async events from FW it's not interested in.
3) Reword a log message for better readability to say that SRIOV
"is disabled" rather than "not supported".
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, the function devm_ioremap_resource() returns
ERR_PTR() and never returns NULL. The NULL test in the return
value check should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-09-12
This series contains updates to e1000, ixgbe and ixgbevf.
Mark provide two fixes to reduce compile warnings produce by ixgbe
and ixgbevf.
Alex provides two patches for ixgbe, first removes the receive buffer
allocation at the end of the ixgbe_clean_rx_irq(). The reason for
removing this is to avoid the extra latency introduced by the MMIO write.
Second patch addresses several issues in the current ixgbe implementation
of busy poll sockets. It was possible for frames to be delivered out of
order if they were held in GRO, so address this by flushing the GRO
buffers before releasing the q_vector back to the idle state. Also, we
were having to take a spinlock on changing the state to and from idle,
so to resolve this, replaced the state value with an atomic and use
atomic_cmpxchg to change the value from idle, and a simple atomic set
to restore it back to idle after we have acquired it. This allows us
to only use a locked operation on acquiring the vector without a need
for a locked operation to release it.
Florian Westphal provides several patches for e1000 which does some
cleanup and updating of the driver. Moved e1000_tbi_adjust_stats()
so that he could make the function static. Added a helper function
to deal with the tbi workaround that was located in 2 different
Rx clean functions. Added a e1000_rx_buffer struct for use on receive
since the transmit and receive have different requirements. Updates
e1000 to use napi_gro_frags API.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending out a burst of packets across multiple descriptors,
it is sufficient to send one LDC "start" trigger for
the first descriptor, so do not send an LDC "start" for every
pass through vnet_start_xmit. Similarly, it is sufficient to send
one "DRING_STOPPED" trigger for the last dring (and if that
fails, hold off and send the trigger later).
Optimizations to the number of LDC messages helps avoid
filling up the LDC channel with superfluous LDC messages
that risk triggering flow-control on the channel,
and also boosts performance.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Raghuram Kothakota <raghuram.kothakota@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
calling ether_setup is redundant since alloc_etherdev calls
it.
Signed-off-by: Subbaraya Sundeep Bhatta <sbhatta@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It will use pr_info_one() to print the version info of the
driver in probe function only once. No need to use the static
variable here.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
and remove *page, its only used for Rx.
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
e1000 uses the same metadata struct for Rx and Tx. But Tx and Rx have
different requirements.
For Rx, we only need to store a buffer and a DMA address.
Follow-up patch will remove skb for Rx, bringing rx_buffer_info down
to 16 bytes on x86_64.
[ buffer_info is 48 bytes ]
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently we unmap the DMA range, then copy to new skb.
Change this so we can keep the mapping in case the data is copied.
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Its the same in both handlers.
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
... and make it static.
Signed-off-by: Florian Westphal <fw@strlen.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change addresses several issues in the current ixgbe implementation of
busy poll sockets.
First was the fact that it was possible for frames to be delivered out of
order if they were held in GRO. This is addressed by flushing the GRO buffers
before releasing the q_vector back to the idle state.
The other issue was the fact that we were having to take a spinlock on
changing the state to and from idle. To resolve this I have replaced the
state value with an atomic and use atomic_cmpxchg to change the value from
idle, and a simple atomic set to restore it back to idle after we have
acquired it. This allows us to only use a locked operation on acquiring the
vector without a need for a locked operation to release it.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change removes the Rx buffer allocation at the end of ixgbe_clean_rx_irq.
The reason for removing this is to avoid the extra latency introduced by the
MMIO write. This can amount to somewhere around an extra 100ns of latency and
one extra message worth of PCIe bus overhead.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Resolve missing-field-initializers warnings by using
designated initialization.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch resolves warnings produced by ixgbe in W=2 kernel
builds. There are missing-field-initializers warnings and shadow
warnings. None of these point to any deeper problem, so just
resolve them so any new warnings get analyzed.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
