STMicroelectronics i2c tpm is the only one to have a different tristate
label.
Rename it "TPM Interface Specification 1.2 Interface (I2C - STMicroelectronics)"
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
[phuewe: corrected module name in the helptext]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
When sending data in tpm_stm_i2c_send, each loop iteration send buf.
Send buf + i instead as the goal of this for loop is to send a number
of byte from buf that fit in burstcnt. Once those byte are sent, we are
supposed to send the next ones.
The driver was working because the burstcount value returns always the maximum size for a TPM
command or response. (0x800 for a command and 0x400 for a response).
Cc: stable@vger.kernel.org
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
The tpm_dev_vendor_release() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
There was an oops in tpm_ibmvtpm_get_desired_dma, which caused
kernel panic during boot when vTPM is enabled in Power partition
configured in AMS mode.
vio_bus_probe calls vio_cmo_bus_probe which calls
tpm_ibmvtpm_get_desired_dma to get the size needed for DMA allocation.
The problem is, vio_cmo_bus_probe is called before calling probe, which
for vtpm is tpm_ibmvtpm_probe and it's this function that initializes
and sets up vtpm's CRQ and gets required data values. Therefore,
since this has not yet been done, NULL is returned in attempt to get
the size for DMA allocation.
We added a NULL check. In addition, a default buffer size will
be set when NULL is returned.
Cc: <stable@vger.kernel.org>
Signed-off-by: Hon Ching (Vicky) Lo <honclo@linux.vnet.ibm.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Some machines, such as the Acer C720 and Toshiba CB35, have TPMs that do
not send IRQs while also having an ACPI TPM entry indicating that they
will be sent. These machines freeze on resume while the tpm_tis module
waits for an IRQ, eventually timing out.
When in interrupt mode, the tpm_tis module should receive an IRQ during
module init. Fall back to polling mode if none is received when expected.
Cc: <stable@vger.kernel.org>
Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
Tested-by: Michael Mullin <masmullin@gmail.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
[phuewe: minor checkpatch fixed]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Currently these driver are missing a check on the return value of devm_kzalloc,
which would cause a NULL pointer dereference in a OOM situation.
This patch adds a missing check for tpm_i2c_atmel.c and tpm_i2c_nuvoton.c
Cc: stable@vger.kernel.org
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Reviewed-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Add newly registered TPMs to the tail of the list, not the beginning, so that
things that are specifying TPM_ANY_NUM don't find that the device they're
using has inadvertently changed. Adding a second device would break IMA, for
instance.
Cc: stable@vger.kernel.org
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Fixes "Missing a blank line after declarations" reported by
checkpatch.
This patch introduces no functional changes.
Signed-off-by: Rob Ward <robert.ward114@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replaces the use of asm/uaccess.h with linux/uaccess.h.
Signed-off-by: Rob Ward <robert.ward114@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify the use of CONFIG_DEVPORT by making the port_fops
so that it includes __maybe_unused.
This enabled the multiple #ifdef's used for this structure
to be removed and brings it in line with the use of CONFIG_DEVMEM
This change should introduce no functional changes.
Signed-off-by: Rob Ward <robert.ward114@googlemail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify the use of CONFIG_DEVKMEM by making the kmem_fops
so that it is __maybe_unused.
This enabled the multiple #ifdef's used for this structure
to be removed and brings it in line with the use of CONFIG_DEVMEM
This change should introduce no functional changes.
Signed-off-by: Rob Ward <robert.ward114@googlemail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds Kconfig option CONFIG_DEVMEM that allows the
/dev/mem device to be disabled.
Option defaults to /dev/mem enabled.
Signed-off-by: Rob Ward <robert.ward114@googlemail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull drm fixes from Dave Airlie:
"Xmas fixes pull:
core:
one atomic fix, revert the WARN_ON dumb buffers patch.
agp:
fixup Dave J.
nouveau:
fix 3.18 regression for old userspace
tegra fixes:
vblank and iommu fixes
amdkfd:
fix bugs shown by testing with userspace, init apertures once
msm:
hdmi fixes and cleanup
i915:
misc fixes
There is also a link ordering fix that I've asked to be cc'ed to you,
putting iommu before gpu, it fixes an issue with amdkfd when things
are all in the kernel, but I didn't like sending it via my tree
without discussion.
I'll probably be a bit on/off for a few weeks with pulls now, due to
holidays and LCA, so don't be surprised if stuff gets a bit backed up,
and things end up a bit large due to lag"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (28 commits)
Revert "drm/gem: Warn on illegal use of the dumb buffer interface v2"
agp: Fix up email address & attributions in AGP MODULE_AUTHOR tags
nouveau: bring back legacy mmap handler
drm/msm/hdmi: rework HDMI IRQ handler
drm/msm/hdmi: enable regulators before clocks to avoid warnings
drm/msm/mdp5: update irqs on crtc<->encoder link change
drm/msm: block incoming update on pending updates
drm/atomic: fix potential null ptr on plane enable
drm/msm: Deletion of unnecessary checks before the function call "release_firmware"
drm/msm: Deletion of unnecessary checks before two function calls
drm/tegra: dc: Select root window for event dispatch
drm/tegra: gem: Use the proper size for GEM objects
drm/tegra: gem: Flush buffer objects upon allocation
drm/tegra: dc: Fix a potential race on page-flip completion
drm/tegra: dc: Consistently use the same pipe
drm/irq: Add drm_crtc_vblank_count()
drm/irq: Add drm_crtc_handle_vblank()
drm/irq: Add drm_crtc_send_vblank_event()
drm/i915: Disable PSMI sleep messages on all rings around context switches
drm/i915: Force the CS stall for invalidate flushes
...
We always do hwrng_init in set_current_rng. In fact, our current
reference count system relies on this. So make this explicit by
moving hwrng_init into set_current_rng.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Rather than having callers of set_current_rng call drop_current_rng,
we can do it directly in set_current_rng.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Currently we only register the device when a valid RNG is added.
However the way it's done is buggy because we test whether there
is a current RNG to determine whether we need to register. As
the current RNG may be missing due to a reinitialisation error
this can lead to a reregistration of the device.
As the device already has to handle a NULL current RNG anyway,
let's just register the device always and remove the complexity.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The kref solution is still buggy because we were only focusing
on the register/unregister race. The same race affects the
setting of current_rng through sysfs.
This patch fixes it by using kref_get_unless_zero.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There is no point in doing a manual completion for cleanup_done
when struct completion fits in perfectly.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
- Remove soon-to-be-dead @redhat address.
- Jeff Hartmann wrote the bulk of the original backend code, and should
at least get a mention in the MODULE_AUTHOR for backend.o
- Various people at Intel have done a lot more work than myself on the
intel-* drivers, so again, mention that.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The previous patch added one potential problem: we can still be
reading from a hwrng when it's unregistered. Add a wait for zero
in the hwrng_unregister path.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
current_rng holds one reference, and we bump it every time we want
to do a read from it.
This means we only hold the rng_mutex to grab or drop a reference,
so accessing /sys/devices/virtual/misc/hw_random/rng_current doesn't
block on read of /dev/hwrng.
Using a kref is overkill (we're always under the rng_mutex), but
a standard pattern.
This also solves the problem that the hwrng_fillfn thread was
accessing current_rng without a lock, which could change (eg. to NULL)
underneath it.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In next patch, we use reference counting for each struct hwrng,
changing reference count also needs to take mutex_lock. Before
releasing the lock, if we try to stop a kthread that waits to
take the lock to reduce the referencing count, deadlock will
occur.
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There's currently a big lock around everything, and it means that we
can't query sysfs (eg /sys/devices/virtual/misc/hw_random/rng_current)
while the rng is reading. This is a real problem when the rng is slow,
or blocked (eg. virtio_rng with qemu's default /dev/random backend)
This doesn't help (it leaves the current lock untouched), just adds a
lock to protect the read function and the static buffers, in preparation
for transition.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The previous cleanup of BMC attributes left a few holes, and if
you run with lockdep debugging with a BMC with the proper attributes,
you could get a warning.
This patch removes all the unused attributes from the BMC structure,
since they are all declared in the .data section now. It makes
the attributes all static. It fixes the referencing of the
attributes in a couple of cases that dynamically added the files
depending on BMC information.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Huang Ying <ying.huang@intel.com>
Tested-by: Alexei Starovoitov <ast@plumgrid.com>
Pull drm updates from Dave Airlie:
"Highlights:
- AMD KFD driver merge
This is the AMD HSA interface for exposing a lowlevel interface for
GPGPU use. They have an open source userspace built on top of this
interface, and the code looks as good as it was going to get out of
tree.
- Initial atomic modesetting work
The need for an atomic modesetting interface to allow userspace to
try and send a complete set of modesetting state to the driver has
arisen, and been suffering from neglect this past year. No more,
the start of the common code and changes for msm driver to use it
are in this tree. Ongoing work to get the userspace ioctl finished
and the code clean will probably wait until next kernel.
- DisplayID 1.3 and tiled monitor exposed to userspace.
Tiled monitor property is now exposed for userspace to make use of.
- Rockchip drm driver merged.
- imx gpu driver moved out of staging
Other stuff:
- core:
panel - MIPI DSI + new panels.
expose suggested x/y properties for virtual GPUs
- i915:
Initial Skylake (SKL) support
gen3/4 reset work
start of dri1/ums removal
infoframe tracking
fixes for lots of things.
- nouveau:
tegra k1 voltage support
GM204 modesetting support
GT21x memory reclocking work
- radeon:
CI dpm fixes
GPUVM improvements
Initial DPM fan control
- rcar-du:
HDMI support added
removed some support for old boards
slave encoder driver for Analog Devices adv7511
- exynos:
Exynos4415 SoC support
- msm:
a4xx gpu support
atomic helper conversion
- tegra:
iommu support
universal plane support
ganged-mode DSI support
- sti:
HDMI i2c improvements
- vmwgfx:
some late fixes.
- qxl:
use suggested x/y properties"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (969 commits)
drm: sti: fix module compilation issue
drm/i915: save/restore GMBUS freq across suspend/resume on gen4
drm: sti: correctly cleanup CRTC and planes
drm: sti: add HQVDP plane
drm: sti: add cursor plane
drm: sti: enable auxiliary CRTC
drm: sti: fix delay in VTG programming
drm: sti: prepare sti_tvout to support auxiliary crtc
drm: sti: use drm_crtc_vblank_{on/off} instead of drm_vblank_{on/off}
drm: sti: fix hdmi avi infoframe
drm: sti: remove event lock while disabling vblank
drm: sti: simplify gdp code
drm: sti: clear all mixer control
drm: sti: remove gpio for HDMI hot plug detection
drm: sti: allow to change hdmi ddc i2c adapter
drm/doc: Document drm_add_modes_noedid() usage
drm/i915: Remove '& 0xffff' from the mask given to WA_REG()
drm/i915: Invert the mask and val arguments in wa_add() and WA_REG()
drm: Zero out DRM object memory upon cleanup
drm/i915/bdw: Fix the write setting up the WIZ hashing mode
...
Here's the big char/misc driver update for 3.19-rc1
Lots of little things all over the place in different drivers, and a new
subsystem, "coresight" has been added. Full details are in the
shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSODosACgkQMUfUDdst+ykSNwCfcqx1Z3rQzbLwSrR2sa1fV3Zb
yEAAniJoLZ4ZkoQK4/1ozsFc31q+gXNm
=/epr
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here's the big char/misc driver update for 3.19-rc1
Lots of little things all over the place in different drivers, and a
new subsystem, "coresight" has been added. Full details are in the
shortlog"
* tag 'char-misc-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (73 commits)
parport: parport_pc, do not remove parent devices early
spmi: Remove shutdown/suspend/resume kernel-doc
carma-fpga-program: drop videobuf dependency
carma-fpga: drop videobuf dependency
carma-fpga-program.c: fix compile errors
i8k: Fix temperature bug handling in i8k_get_temp()
cxl: Name interrupts in /proc/interrupt
CXL: Return error to PSL if IRQ demultiplexing fails & print clearer warning
coresight-replicator: remove .owner field for driver
coresight: fixed comments in coresight.h
coresight: fix typo in comment in coresight-priv.h
coresight: bindings for coresight drivers
coresight: Adding ABI documentation
w1: support auto-load of w1_bq27000 module.
w1: avoid potential u16 overflow
cn: verify msg->len before making callback
mei: export fw status registers through sysfs
mei: read and print all six FW status registers
mei: txe: add cherrytrail device id
mei: kill cached host and me csr values
...
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Pull crypto update from Herbert Xu:
- The crypto API is now documented :)
- Disallow arbitrary module loading through crypto API.
- Allow get request with empty driver name through crypto_user.
- Allow speed testing of arbitrary hash functions.
- Add caam support for ctr(aes), gcm(aes) and their derivatives.
- nx now supports concurrent hashing properly.
- Add sahara support for SHA1/256.
- Add ARM64 version of CRC32.
- Misc fixes.
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (77 commits)
crypto: tcrypt - Allow speed testing of arbitrary hash functions
crypto: af_alg - add user space interface for AEAD
crypto: qat - fix problem with coalescing enable logic
crypto: sahara - add support for SHA1/256
crypto: sahara - replace tasklets with kthread
crypto: sahara - add support for i.MX53
crypto: sahara - fix spinlock initialization
crypto: arm - replace memset by memzero_explicit
crypto: powerpc - replace memset by memzero_explicit
crypto: sha - replace memset by memzero_explicit
crypto: sparc - replace memset by memzero_explicit
crypto: algif_skcipher - initialize upon init request
crypto: algif_skcipher - removed unneeded code
crypto: algif_skcipher - Fixed blocking recvmsg
crypto: drbg - use memzero_explicit() for clearing sensitive data
crypto: drbg - use MODULE_ALIAS_CRYPTO
crypto: include crypto- module prefix in template
crypto: user - add MODULE_ALIAS
crypto: sha-mb - remove a bogus NULL check
crytpo: qat - Fix 64 bytes requests
...
On a reset, the BMC may reset the BT enable in the processor
registers (different than the global enables in the BMC). Check
it periodically and fix it if necessary.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Tony Rex <tony.rex@ericsson.com>
Tested-by: Magnus Johansson E <magnus.e.johansson@ericsson.com>
If an attention came in while handling a message response, it
could cause the state machine to go into the wrong mode and lock
things up if the state machine wasn't in normal mode. So if the
state machine is not in normal mode, save the attention flag for
later.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Tony Rex <tony.rex@ericsson.com>
Tested-by: Magnus Johansson E <magnus.e.johansson@ericsson.com>
Cc: Per Fogelström <per.fogelstrom@ericsson.com>
The BMC can be reset while we are running; that means the interrupt
and event message buffer settings may be wrong. So periodically
check to see if these values are correct, and fix them if they
are wrong.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Tested-by: Tony Rex <tony.rex@ericsson.com>
Tested-by: Magnus Johansson E <magnus.e.johansson@ericsson.com>
This change adds an initial IPMI driver for powerpc OPAL firmware. The
interface is exposed entirely through firmware: we have two functions to
send and receive IPMI messages, and an interrupt notification from the
firmware to signify that a message is available.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
A message queue was added to the message handler, so the SMI
interfaces only need to handle one message at a time. Pull out
the message queue. This also leads to some significant
simplification in the shutdown of an interface, since the
message handler now does a lot of the cleanup.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The message handler expected the SMI interface to keep a queue of
messages, but that was kind of silly, the queue would be easier to
manage in the message handler itself. As part of that, fix the
message cleanup to make sure no messages are outstanding when an
SMI interface is unregistered. This makes it easier for an SMI
interface to unregister, it just has to call ipmi_unregister_smi()
first and all processing from the message handler will be cleaned
up.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The handling of BMC flags wasn't quite right in a few places, mainly
around enabling and disabling interrupts in the BMC. Clean up the
code and fix the handling of the flags.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Embed the platform device in the bmc device instead of externally
allocating it, use more proper form for creating the device
attributes, and other general cleanups.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
This adds a lot of infrastructure for virtio 1.0 support.
Notable missing pieces: virtio pci, virtio balloon (needs spec extension),
vhost scsi.
Plus, there are some minor fixes in a couple of places.
Cc: David Miller <davem@davemloft.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUh1CVAAoJECgfDbjSjVRpWZcH/2+EGPyng7Lca820UHA0cU1U
u4D8CAAwOGaVdnUUo8ox1eon3LNB2UgRtgsl3rBDR3YTgFfNPrfuYdnHO0dYIDc1
lS26NuPrVrTX0lA+OBPe2nlKrsrOkn8aw1kxG9Y0gKtNg/+HAGNW5e2eE7R/LrA5
94XbWZ8g9Yf4GPG1iFmih9vQvvN0E68zcUlojfCnllySgaIEYr8nTiGQBWpRgJat
fCqFAp1HMDZzGJQO+m1/Vw0OftTRVybyfai59e6uUTa8x1djvzPb/1MvREqQjegM
ylSuofIVyj7JPu++FbAjd9mikkb53GSc8ql3YmWNZLdr69rnkzP0GdzQvrdheAo=
=RtrR
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
"virtio: virtio 1.0 support, misc patches
This adds a lot of infrastructure for virtio 1.0 support. Notable
missing pieces: virtio pci, virtio balloon (needs spec extension),
vhost scsi.
Plus, there are some minor fixes in a couple of places.
Note: some net drivers are affected by these patches. David said he's
fine with merging these patches through my tree.
Rusty's on vacation, he acked using my tree for these, too"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (70 commits)
virtio_ccw: finalize_features error handling
virtio_ccw: future-proof finalize_features
virtio_pci: rename virtio_pci -> virtio_pci_common
virtio_pci: update file descriptions and copyright
virtio_pci: split out legacy device support
virtio_pci: setup config vector indirectly
virtio_pci: setup vqs indirectly
virtio_pci: delete vqs indirectly
virtio_pci: use priv for vq notification
virtio_pci: free up vq->priv
virtio_pci: fix coding style for structs
virtio_pci: add isr field
virtio: drop legacy_only driver flag
virtio_balloon: drop legacy_only driver flag
virtio_ccw: rev 1 devices set VIRTIO_F_VERSION_1
virtio: allow finalize_features to fail
virtio_ccw: legacy: don't negotiate rev 1/features
virtio: add API to detect legacy devices
virtio_console: fix sparse warnings
vhost: remove unnecessary forward declarations in vhost.h
...
This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come
from as long as the platform firmware (either DT or ACPI) makes
them available. It covers both devices and "bare" device node
objects without struct device representation as that turns out to
be necessary in some cases. This has been in the works for quite
a few months (and development cycles) and has been approved by
all of the relevant maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO information
in their ACPI tables, but don't assign names to GPIO lines (in which
case the driver needs to do that on the basis of what it knows about
the device in question). That also has been approved by the GPIO
core maintainers and the rfkill driver is now going to use it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by
the processor in which case it will be enabled by default. However,
it can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller).
The support added this time is sufficient to make the ACPI battery
driver work on Asus T100A, but it is general enough to be able to
cover some other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver
for Intel platforms should be able to handle power management of
the DMA engine correctly, the cpufreq-dt driver should interact
with the thermal subsystem in a better way and the ACPI backlight
driver should handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions
in the ACPICA's interrupt handling code which might lead to some
random and strange looking failures on some systems.
In the cleanups department the most visible part is the series
of commits targeted at getting rid of the CONFIG_PM_RUNTIME
configuration option. That was triggered by a discussion
regarding the generic power domains code during which we realized
that trying to support certain combinations of PM config options
was painful and not really worth it, because nobody would use them
in production anyway. For this reason, we decided to make
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and that lead to the
conclusion that the latter became redundant and CONFIG_PM could
be used instead of it. The material here makes that replacement
in a major part of the tree, but there will be at least one more
batch of that in the second part of the merge window.
Specifics:
- Support for retrieving device properties information from ACPI
_DSD device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that.
As stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers
are now going to use this new interface and the GPIO subsystem
is additionally modified to allow device drivers to assign names
to GPIO resources returned by ACPI _CRS objects (in case _DSD is
not present or does not provide the expected data). The changes
in this set are mostly from Mika Westerberg, Rafael J Wysocki,
Aaron Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions
used by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management
(Aaron Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects
and deferred probing support for the ACPI battery driver based
on the _DEP information to make that driver work on Asus T100A
(Lan Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling
code and in the ACPI code related to system suspend and resume
(Lv Zheng and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had
been allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in
that code with synchronize_rcu_expedited() which makes the issue
go away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly.
The problem is that the DMA engine doesn't have ACPI PM support
of its own and it simply is turned off when the last LPSS device
having ACPI PM support goes into D3cold. To work around that,
the PM domain used by the ACPI LPSS driver is redesigned so at
least one device with ACPI PM support will be on as long as the
DMA engine is in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and
Ashwin Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver
fixes and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at
probe time (Ulf Hansson).
- Preliminary support for controlling device clocks from the
generic power domains core code and modifications of the
ARM/shmobile platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power
domains core code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control
code in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and
a new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu,
James Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to
allow OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and
Markus Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5dox
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come from
as long as the platform firmware (either DT or ACPI) makes them
available. It covers both devices and "bare" device node objects
without struct device representation as that turns out to be necessary
in some cases. This has been in the works for quite a few months (and
development cycles) and has been approved by all of the relevant
maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO
information in their ACPI tables, but don't assign names to GPIO lines
(in which case the driver needs to do that on the basis of what it
knows about the device in question). That also has been approved by
the GPIO core maintainers and the rfkill driver is now going to use
it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by the
processor in which case it will be enabled by default. However, it
can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller). The
support added this time is sufficient to make the ACPI battery driver
work on Asus T100A, but it is general enough to be able to cover some
other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
Intel platforms should be able to handle power management of the DMA
engine correctly, the cpufreq-dt driver should interact with the
thermal subsystem in a better way and the ACPI backlight driver should
handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions in the
ACPICA's interrupt handling code which might lead to some random and
strange looking failures on some systems.
In the cleanups department the most visible part is the series of
commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
option. That was triggered by a discussion regarding the generic
power domains code during which we realized that trying to support
certain combinations of PM config options was painful and not really
worth it, because nobody would use them in production anyway. For
this reason, we decided to make CONFIG_PM_SLEEP select
CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
became redundant and CONFIG_PM could be used instead of it. The
material here makes that replacement in a major part of the tree, but
there will be at least one more batch of that in the second part of
the merge window.
Specifics:
- Support for retrieving device properties information from ACPI _DSD
device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that. As
stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are
now going to use this new interface and the GPIO subsystem is
additionally modified to allow device drivers to assign names to
GPIO resources returned by ACPI _CRS objects (in case _DSD is not
present or does not provide the expected data). The changes in
this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions used
by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management (Aaron
Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects and
deferred probing support for the ACPI battery driver based on the
_DEP information to make that driver work on Asus T100A (Lan
Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling code
and in the ACPI code related to system suspend and resume (Lv Zheng
and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had been
allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in that
code with synchronize_rcu_expedited() which makes the issue go
away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly. The
problem is that the DMA engine doesn't have ACPI PM support of its
own and it simply is turned off when the last LPSS device having
ACPI PM support goes into D3cold. To work around that, the PM
domain used by the ACPI LPSS driver is redesigned so at least one
device with ACPI PM support will be on as long as the DMA engine is
in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver fixes
and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at probe
time (Ulf Hansson).
- Preliminary support for controlling device clocks from the generic
power domains core code and modifications of the ARM/shmobile
platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power domains core
code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control code
in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to allow
OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and Markus
Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava)"
* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
leds: leds-gpio: Fix multiple instances registration without 'label' property
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
...
While there normally is no reason to have a pull request for asm-generic
but have all changes get merged through whichever tree needs them, I do
have a series for 3.19. There are two sets of patches that change
significant portions of asm/io.h, and this branch contains both in order
to resolve the conflicts:
- Will Deacon has done a set of patches to ensure that all architectures
define {read,write}{b,w,l,q}_relaxed() functions or get them by
including asm-generic/io.h. These functions are commonly used on ARM
specific drivers to avoid expensive L2 cache synchronization implied by
the normal {read,write}{b,w,l,q}, but we need to define them on all
architectures in order to share the drivers across architectures and
to enable CONFIG_COMPILE_TEST configurations for them
- Thierry Reding has done an unrelated set of patches that extends
the asm-generic/io.h file to the degree necessary to make it useful
on ARM64 and potentially other architectures.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xUv6
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic asm/io.h rewrite from Arnd Bergmann:
"While there normally is no reason to have a pull request for
asm-generic but have all changes get merged through whichever tree
needs them, I do have a series for 3.19.
There are two sets of patches that change significant portions of
asm/io.h, and this branch contains both in order to resolve the
conflicts:
- Will Deacon has done a set of patches to ensure that all
architectures define {read,write}{b,w,l,q}_relaxed() functions or
get them by including asm-generic/io.h.
These functions are commonly used on ARM specific drivers to avoid
expensive L2 cache synchronization implied by the normal
{read,write}{b,w,l,q}, but we need to define them on all
architectures in order to share the drivers across architectures
and to enable CONFIG_COMPILE_TEST configurations for them
- Thierry Reding has done an unrelated set of patches that extends
the asm-generic/io.h file to the degree necessary to make it useful
on ARM64 and potentially other architectures"
* tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (29 commits)
ARM64: use GENERIC_PCI_IOMAP
sparc: io: remove duplicate relaxed accessors on sparc32
ARM: sa11x0: Use void __iomem * in MMIO accessors
arm64: Use include/asm-generic/io.h
ARM: Use include/asm-generic/io.h
asm-generic/io.h: Implement generic {read,write}s*()
asm-generic/io.h: Reconcile I/O accessor overrides
/dev/mem: Use more consistent data types
Change xlate_dev_{kmem,mem}_ptr() prototypes
ARM: ixp4xx: Properly override I/O accessors
ARM: ixp4xx: Fix build with IXP4XX_INDIRECT_PCI
ARM: ebsa110: Properly override I/O accessors
ARC: Remove redundant PCI_IOBASE declaration
documentation: memory-barriers: clarify relaxed io accessor semantics
x86: io: implement dummy relaxed accessor macros for writes
tile: io: implement dummy relaxed accessor macros for writes
sparc: io: implement dummy relaxed accessor macros for writes
powerpc: io: implement dummy relaxed accessor macros for writes
parisc: io: implement dummy relaxed accessor macros for writes
mn10300: io: implement dummy relaxed accessor macros for writes
...
CHECK drivers/char/virtio_console.c
drivers/char/virtio_console.c:687:36: warning: incorrect type in
argument 1 (different address spaces)
drivers/char/virtio_console.c:687:36: expected void [noderef]
<asn:1>*to
drivers/char/virtio_console.c:687:36: got char *out_buf
drivers/char/virtio_console.c:790:35: warning: incorrect type in
argument 2 (different address spaces)
drivers/char/virtio_console.c:790:35: expected char *out_buf
drivers/char/virtio_console.c:790:35: got char [noderef]
<asn:1>*ubuf
fill_readbuf is reused with both kernel and userspace pointers,
depending on value of to_user flag.
Tag address parameter as __user, and cast to/from regular pointer type
when we know it's safe.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It seemed like a good idea to use bitmap for features
in struct virtio_device, but it's actually a pain,
and seems to become even more painful when we get more
than 32 feature bits. Just change it to a u32 for now.
Based on patch by Rusty.
Suggested-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
CONFIG_PM is defined as the alternative of CONFIG_PM_RUNTIME and
CONFIG_PM_SLEEP, so it can be used instead of that.
Besides, after commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if
PM_SLEEP is selected) PM_RUNTIME is always set if PM is set, so
using the alternative isn't even necessary.
Use CONFIG_PM instead of it in drivers/char/hw_random/exynos-rng.c.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Static array prev[] was incorrectly initialized. It should be initialized to
some "invalid" temperature value (above I8K_MAX_TEMP).
Next, function should store "invalid" value to prev[] (above I8K_MAX_TEMP),
not valid (= I8K_MAX_TEMP) because whole temperature bug handling will not
work.
And last part, to not break existing detection of temperature sensors, register
them also if i8k report too high temperature (above I8K_MAX_TEMP). This is
needed because some sensors are sometimes turned off (e.g sensor on GPU which
can be turned off/on) and in this case SMM report too high value.
To prevent reporting "invalid" values to userspace, return -EINVAL. In this case
sensors which are currently turned off (e.g optimus/powerexpress/enduro gpu)
are reported as "N/A" by lm-sensors package.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add DT support.
Make the driver depend on CONFIG_OF as at91sam9g45 was the only SoC making
use of the TRNG block and this SoC is now fully migrated to DT.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use clk_prepare_enable/_disable_unprepare instead of clk_enable/disable
to work properly with the CCF.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This reverts commit 32eca22180.
Changing core kernel code to operate in a different manner, without a
build-time breakage is tough to do and ensure you got it right. There
are lots of problems popping up due to this change, so let's revert it
for now as it is not safe to merge to the tree at this point in time.
Cc: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 965ab29ba0.
This is causing way more problems than it is worth.
Cc: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a crash in virtio console
multi-channel mode that got introduced in -rc1.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUZSAsAAoJECgfDbjSjVRpsqkIAJdGYmLWLHmU1FeuT336FbD6
4mj9+b9PX+gG6pjEyWcM/hEEx7MHp/0+evyeFXkeVwSdKxoV9/F/VRAMW/LnyNvS
rsJmv8ptvEscGwvwLHwnV4/xBcY8z676JxcnE4E/0KFLhRoP3h8/Bwel9wl0R8Sp
BDV0ddZLbPOzCgVgOGgXkEZ7xmhwHsSlRJO6wpkzB7c4Z8QJjx6cbdiM4XcTnaaM
nX5HsAG0y3Dm6CwNYrXukv4obxyOsVyt1kJGOiTjnzqhqUCFARRRM3CyDNV8+IbM
qUFArNxdMoUfyhCkDqyLdrOw0gwsWkXWErunkgzPKYY3lYUF8NxqFCKbAhTwrSY=
=tNTR
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio bugfix from Michael S Tsirkin:
"This fixes a crash in virtio console multi-channel mode that got
introduced in -rc1"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_console: move early VQ enablement
Commit f5866db6 (virtio_console: enable VQs early) tried to make
sure that DRIVER_OK was set when virtio_console started using its
virtqueues. Doing this in add_port(), however, means that we try
to set DRIVER_OK again when when a port is dynamically added after
the probe function is done.
Let's move virtio_device_ready() to the probe function just before
trying to use the virtqueues instead. This is fine as nothing can
fail inbetween.
Reported-by: Thomas Graf <tgraf@suug.ch>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Pull crypto fixes from Herbert Xu:
- stack corruption fix for pseries hwrng driver
- add missing DMA unmap in caam crypto driver
- fix NUMA crash in qat crypto driver
- fix buggy mapping of zero-length associated data in qat crypto driver
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
hwrng: pseries - port to new read API and fix stack corruption
crypto: caam - fix missing dma unmap on error path
crypto: qat - Enforce valid numa configuration
crypto: qat - Prevent dma mapping zero length assoc data
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUX/DqAAoJEHm+PkMAQRiGLtQH/iAt3fRHlYDXjaJian/KG1Cb
wVP0I+HWZmvVmmd0PzyaxCZLgRNwdmmYHEH4QLy2JwZ3jZfFHlxhy+hDWCgz+67t
bIzkLs0Pf1T4kJ2+r8qW2kBEz9PWJHGTQw7NTqZ++Ts3rPptBA6Fg4mEJ6fQigXy
qRIY68DpipUkXV9BWBWijnTmrvP5tt7JtPzBr4DC8frMjvWct8+XwYhc2k2tEv2j
LwLYb1OW6PUpPv2BQBfWjqqH77vYNQVhJwuwGcDe2YZdI0UFkDheL24+RbbPcZ4f
OnrLjJSSgzv6lBWkAaXZK7/WJ/JZbXxEqHzWZQ3xXoQov97bm7lEYJqqi5gDasQ=
=6Qpa
-----END PGP SIGNATURE-----
Merge tag 'v3.18-rc4' into drm-next
backmerge to get vmwgfx locking changes into next as the
conflict with per-plane locking.
The xlate_dev_{kmem,mem}_ptr() functions take either a physical address
or a kernel virtual address, so data types should be phys_addr_t and
void *. They both return a kernel virtual address which is only ever
used in calls to copy_{from,to}_user(), so make variables that store it
void * rather than char * for consistency.
Also only define a weak unxlate_dev_mem_ptr() function if architectures
haven't overridden them in the asm/io.h header file.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The 32 bit addition "(hangcheck_margin + hangcheck_tick)" could
potentially overflow. It triggers a static checker warning to have an
overflowed addition followed by a no-op cast. I have moved the cast so
that the addition can't overflow.
Also I removed the unneeded cast on the following line since both
"hangcheck_tsc_margin" and "TIMER_FREQ" are already 64 bit types.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
an open syscall now assignes file->private_data to a pointer to the
miscdevice structure. This reminds driver developers not to duplicate
code if they need this.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As of now, a miscdevice driver has to provide an implementation of
the open() file operation if it wants to have misc_open() assign a
pointer to struct miscdevice to file->private_data for other file
operations to use (given the user calls open()).
This leads to situations where a miscdevice driver that doesn't need
internal operations during open() has to implement open() that only
returns immediately, in order to use the data in private_data in other
fops.
This provides consistent behaviour for miscdevice developers and will
always provide the pointer in private_data. A driver's open() fop would,
of course, just overwrite it, when using private_data itself.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds MODULE_DEVICE_TABLE macro so i8k.ko module can be automatically
loaded based on dmi system alias.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The add_early_randomness() function in drivers/char/hw_random/core.c passes
a 16-byte buffer to pseries_rng_data_read(). Unfortunately, plpar_hcall()
returns four 64-bit values and trashes 16 bytes on the stack.
This bug has been lying around for a long time. It got unveiled by:
commit d3cc799647
Author: Amit Shah <amit.shah@redhat.com>
Date: Thu Jul 10 15:42:34 2014 +0530
hwrng: fetch randomness only after device init
It may trig a oops while loading or unloading the pseries-rng module for both
PowerVM and PowerKVM guests.
This patch does two things:
- pass an intermediate well sized buffer to plpar_hcall(). This is acceptalbe
since we're not on a hot path.
- move to the new read API so that we know the return buffer size for sure.
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Author: David Jeffery <djeffery@redhat.com>
Changes to the basic direct I/O code have broken the raw driver when reading
to the end of a raw device. Instead of returning a short read for a read that
extends partially beyond the device's end or 0 when at the end of the device,
these reads now return EIO.
The raw driver needs the same end of device handling as was added for normal
block devices. Using blkdev_read_iter, which has the needed size checks,
prevents the EIO conditions at the end of the device.
Signed-off-by: David Jeffery <djeffery@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Ok, new attempt, this time around with full ppgtt disabled again.
drm-intel-next-2014-10-03:
- first batch of skl stage 1 enabling
- fixes from Rodrigo to the PSR, fbc and sink crc code
- kerneldoc for the frontbuffer tracking code, runtime pm code and the basic
interrupt enable/disable functions
- smaller stuff all over
drm-intel-next-2014-09-19:
- bunch more i830M fixes from Ville
- full ppgtt now again enabled by default
- more ppgtt fixes from Michel Thierry and Chris Wilson
- plane config work from Gustavo Padovan
- spinlock clarifications
- piles of smaller improvements all over, as usual
* tag 'drm-intel-next-2014-10-03-no-ppgtt' of git://anongit.freedesktop.org/drm-intel: (114 commits)
Revert "drm/i915: Enable full PPGTT on gen7"
drm/i915: Update DRIVER_DATE to 20141003
drm/i915: Remove the duplicated logic between the two shrink phases
drm/i915: kerneldoc for interrupt enable/disable functions
drm/i915: Use dev_priv instead of dev in irq setup functions
drm/i915: s/pm._irqs_disabled/pm.irqs_enabled/
drm/i915: Clear TX FIFO reset master override bits on chv
drm/i915: Make sure hardware uses the correct swing margin/deemph bits on chv
drm/i915: make sink_crc return -EIO on aux read/write failure
drm/i915: Constify send buffer for intel_dp_aux_ch
drm/i915: De-magic the PSR AUX message
drm/i915: Reinstate error level message for non-simulated gpu hangs
drm/i915: Kerneldoc for intel_runtime_pm.c
drm/i915: Call runtime_pm_disable directly
drm/i915: Move intel_display_set_init_power to intel_runtime_pm.c
drm/i915: Bikeshed rpm functions name a bit.
drm/i915: Extract intel_runtime_pm.c
drm/i915: Remove intel_modeset_suspend_hw
drm/i915: spelling fixes for frontbuffer tracking kerneldoc
drm/i915: Tighting frontbuffer tracking around flips
...
optimized away by GCC. This is important when we are wiping
cryptographically sensitive material.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=i29U
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull /dev/random updates from Ted Ts'o:
"This adds a memzero_explicit() call which is guaranteed not to be
optimized away by GCC. This is important when we are wiping
cryptographically sensitive material"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
crypto: memzero_explicit - make sure to clear out sensitive data
random: add and use memzero_explicit() for clearing data
The buf is used to hold the list of hwrng devices registered.
The old code ensures we don't walk off the end of buf as we
fill it, but it's unnecessarily complicated and thus difficult
to maintain. Simplify it by using strlcat.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Reviewed-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
been sitting in MST's tree during my vacation. I changed a function name
and made one trivial change, then they spent two days in linux-next.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=JK6x
-----END PGP SIGNATURE-----
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio updates from Rusty Russell:
"One cc: stable commit, the rest are a series of minor cleanups which
have been sitting in MST's tree during my vacation. I changed a
function name and made one trivial change, then they spent two days in
linux-next"
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (25 commits)
virtio-rng: refactor probe error handling
virtio_scsi: drop scan callback
virtio_balloon: enable VQs early on restore
virtio_scsi: fix race on device removal
virito_scsi: use freezable WQ for events
virtio_net: enable VQs early on restore
virtio_console: enable VQs early on restore
virtio_scsi: enable VQs early on restore
virtio_blk: enable VQs early on restore
virtio_scsi: move kick event out from virtscsi_init
virtio_net: fix use after free on allocation failure
9p/trans_virtio: enable VQs early
virtio_console: enable VQs early
virtio_blk: enable VQs early
virtio_net: enable VQs early
virtio: add API to enable VQs early
virtio_net: minor cleanup
virtio-net: drop config_mutex
virtio_net: drop config_enable
virtio-blk: drop config_mutex
...
zatimend has reported that in his environment (3.16/gcc4.8.3/corei7)
memset() calls which clear out sensitive data in extract_{buf,entropy,
entropy_user}() in random driver are being optimized away by gcc.
Add a helper memzero_explicit() (similarly as explicit_bzero() variants)
that can be used in such cases where a variable with sensitive data is
being cleared out in the end. Other use cases might also be in crypto
code. [ I have put this into lib/string.c though, as it's always built-in
and doesn't need any dependencies then. ]
Fixes kernel bugzilla: 82041
Reported-by: zatimend@hotmail.co.uk
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
Pull percpu consistent-ops changes from Tejun Heo:
"Way back, before the current percpu allocator was implemented, static
and dynamic percpu memory areas were allocated and handled separately
and had their own accessors. The distinction has been gone for many
years now; however, the now duplicate two sets of accessors remained
with the pointer based ones - this_cpu_*() - evolving various other
operations over time. During the process, we also accumulated other
inconsistent operations.
This pull request contains Christoph's patches to clean up the
duplicate accessor situation. __get_cpu_var() uses are replaced with
with this_cpu_ptr() and __this_cpu_ptr() with raw_cpu_ptr().
Unfortunately, the former sometimes is tricky thanks to C being a bit
messy with the distinction between lvalues and pointers, which led to
a rather ugly solution for cpumask_var_t involving the introduction of
this_cpu_cpumask_var_ptr().
This converts most of the uses but not all. Christoph will follow up
with the remaining conversions in this merge window and hopefully
remove the obsolete accessors"
* 'for-3.18-consistent-ops' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (38 commits)
irqchip: Properly fetch the per cpu offset
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t -fix
ia64: sn_nodepda cannot be assigned to after this_cpu conversion. Use __this_cpu_write.
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t
Revert "powerpc: Replace __get_cpu_var uses"
percpu: Remove __this_cpu_ptr
clocksource: Replace __this_cpu_ptr with raw_cpu_ptr
sparc: Replace __get_cpu_var uses
avr32: Replace __get_cpu_var with __this_cpu_write
blackfin: Replace __get_cpu_var uses
tile: Use this_cpu_ptr() for hardware counters
tile: Replace __get_cpu_var uses
powerpc: Replace __get_cpu_var uses
alpha: Replace __get_cpu_var
ia64: Replace __get_cpu_var uses
s390: cio driver &__get_cpu_var replacements
s390: Replace __get_cpu_var uses
mips: Replace __get_cpu_var uses
MIPS: Replace __get_cpu_var uses in FPU emulator.
arm: Replace __this_cpu_ptr with raw_cpu_ptr
...
Code like
vi->vq = NULL;
kfree(vi)
does not make sense.
Clean it up, use goto error labels for cleanup.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
virtio spec requires drivers to set DRIVER_OK before using VQs.
This is set automatically after resume returns, virtio console violated this
rule by adding inbufs, which causes the VQ to be used directly within
restore.
To fix, call virtio_device_ready before using VQs.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
virtio spec requires drivers to set DRIVER_OK before using VQs.
This is set automatically after probe returns, virtio console violated this
rule by adding inbufs, which causes the VQ to be used directly within
probe.
To fix, call virtio_device_ready before using VQs.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Pull vfs updates from Al Viro:
"The big thing in this pile is Eric's unmount-on-rmdir series; we
finally have everything we need for that. The final piece of prereqs
is delayed mntput() - now filesystem shutdown always happens on
shallow stack.
Other than that, we have several new primitives for iov_iter (Matt
Wilcox, culled from his XIP-related series) pushing the conversion to
->read_iter()/ ->write_iter() a bit more, a bunch of fs/dcache.c
cleanups and fixes (including the external name refcounting, which
gives consistent behaviour of d_move() wrt procfs symlinks for long
and short names alike) and assorted cleanups and fixes all over the
place.
This is just the first pile; there's a lot of stuff from various
people that ought to go in this window. Starting with
unionmount/overlayfs mess... ;-/"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (60 commits)
fs/file_table.c: Update alloc_file() comment
vfs: Deduplicate code shared by xattr system calls operating on paths
reiserfs: remove pointless forward declaration of struct nameidata
don't need that forward declaration of struct nameidata in dcache.h anymore
take dname_external() into fs/dcache.c
let path_init() failures treated the same way as subsequent link_path_walk()
fix misuses of f_count() in ppp and netlink
ncpfs: use list_for_each_entry() for d_subdirs walk
vfs: move getname() from callers to do_mount()
gfs2_atomic_open(): skip lookups on hashed dentry
[infiniband] remove pointless assignments
gadgetfs: saner API for gadgetfs_create_file()
f_fs: saner API for ffs_sb_create_file()
jfs: don't hash direct inode
[s390] remove pointless assignment of ->f_op in vmlogrdr ->open()
ecryptfs: ->f_op is never NULL
android: ->f_op is never NULL
nouveau: __iomem misannotations
missing annotation in fs/file.c
fs: namespace: suppress 'may be used uninitialized' warnings
...
- Add pvscsi frontend and backend drivers.
- Remove _PAGE_IOMAP PTE flag, freeing it for alternate uses.
- Try and keep memory contiguous during PV memory setup (reduces
SWIOTLB usage).
- Allow front/back drivers to use threaded irqs.
- Support large initrds in PV guests.
- Fix PVH guests in preparation for Xen 4.5
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJUNonmAAoJEFxbo/MsZsTRHAQH/inCjpCT+pkvTB0YAVfVvgMI
gUogT8G+iB2MuCNpMffGIt8TAVXwcVtnOLH9ABH3IBVehzgipIbIiVEM9YhjrYvU
1rgIKBpmZqSpjDHoIHpdHeCH67cVnRzA/PyoxZWLxPNmQ0t6bNf9yeAcCXK9PfUc
7EAblUDmPGSx9x/EUnOKNNaZSEiUJZHDBXbMBLllk1+5H1vfKnpFCRGMG0IrfI44
KVP2NX9Gfa05edMZYtH887FYyjFe2KNV6LJvE7+w7h2Dy0yIzf7y86t0l4n8gETb
plvEUJ/lu9RYzTiZY/RxgBFYVTV59EqT45brSUtoe2Jcp8GSwiHslTHdfyFBwSo=
=gw4d
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.18-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen updates from David Vrabel:
"Features and fixes:
- Add pvscsi frontend and backend drivers.
- Remove _PAGE_IOMAP PTE flag, freeing it for alternate uses.
- Try and keep memory contiguous during PV memory setup (reduces
SWIOTLB usage).
- Allow front/back drivers to use threaded irqs.
- Support large initrds in PV guests.
- Fix PVH guests in preparation for Xen 4.5"
* tag 'stable/for-linus-3.18-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (22 commits)
xen: remove DEFINE_XENBUS_DRIVER() macro
xen/xenbus: Remove BUG_ON() when error string trucated
xen/xenbus: Correct the comments for xenbus_grant_ring()
x86/xen: Set EFER.NX and EFER.SCE in PVH guests
xen: eliminate scalability issues from initrd handling
xen: sync some headers with xen tree
xen: make pvscsi frontend dependant on xenbus frontend
arm{,64}/xen: Remove "EXPERIMENTAL" in the description of the Xen options
xen-scsifront: don't deadlock if the ring becomes full
x86: remove the Xen-specific _PAGE_IOMAP PTE flag
x86/xen: do not use _PAGE_IOMAP PTE flag for I/O mappings
x86: skip check for spurious faults for non-present faults
xen/efi: Directly include needed headers
xen-scsiback: clean up a type issue in scsiback_make_tpg()
xen-scsifront: use GFP_ATOMIC under spin_lock
MAINTAINERS: Add xen pvscsi maintainer
xen-scsiback: Add Xen PV SCSI backend driver
xen-scsifront: Add Xen PV SCSI frontend driver
xen: Add Xen pvSCSI protocol description
xen/events: support threaded irqs for interdomain event channels
...
Here's the big set of driver patches for char/misc drivers. Nothing
major in here, the shortlog below goes into the details. All have been
in the linux-next tree for a while with no issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlQ0ZXYACgkQMUfUDdst+ymiEgCgrKcYUluvdrbjdkhrENk332YN
lcUAoMzgQpbkYhswrDNQet7NtAbFN9LV
=ZPDy
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here's the big set of driver patches for char/misc drivers. Nothing
major in here, the shortlog goes into the details. All have been in
the linux-next tree for a while with no issues"
* tag 'char-misc-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (80 commits)
mei: mei_txe_fw_sts can be static
mei: fix kernel-doc warnings
mei: fix KDoc documentation formatting
mei: drop me_client_presentation_num
mei: trivial: fix errors in prints in comments
mei: remove include to pci header from mei module files
mei: push pci cfg structure me hw
mei: remove the reference to pdev from mei_device
mei: move fw_status back to hw ops handlers
mei: get rid of most of the pci dependencies in mei
mei: push all standard settings into mei_device_init
mei: move mei_hbm_hdr function from hbm.h the hbm.c
mei: kill error message for allocation failure
mei: nfc: fix style warning
mei: fix style warning: Missing a blank line after declarations
mei: pg: fix cat and paste error in comments
mei: debugfs: add single buffer indicator
mei: debugfs: adjust print buffer
mei: add hbm and pg state in devstate debugfs print
Drivers: hv: vmbus: Enable interrupt driven flow control
...
Here is the big staging patch set for 3.18-rc1.
Once again, we are deleting more code than we added, with something like
150000 lines deleted overall. Some of this is due to drivers being
added to the networking tree, so the old versions are removed here, but
even then, the overall difference is quite good.
Other than driver deletions, lots and lots and lots of minor cleanups
all over the place. Full details are in the shortlog below.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlQ0Z2oACgkQMUfUDdst+ymy/wCffkFU9h0FAt8KYYQAUIrOQlRx
iFgAnik8M5tVMm5BNCzbiELz8BDiXPTh
=otKa
-----END PGP SIGNATURE-----
Merge tag 'staging-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging updates from Greg KH:
"Here is the big staging patch set for 3.18-rc1.
Once again, we are deleting more code than we added, with something
like 150000 lines deleted overall. Some of this is due to drivers
being added to the networking tree, so the old versions are removed
here, but even then, the overall difference is quite good.
Other than driver deletions, lots and lots and lots of minor cleanups
all over the place. Full details are in the changelog"
* tag 'staging-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1481 commits)
staging: et131x: Remove et131x driver from drivers/staging
staging: emxx_udc: Use min_t instead of min
staging: emxx_udc: Fix replace printk(KERN_DEBUG ..) with dev_dbg
staging: media: Fixed else after return or break warning
staging: media: omap4iss: Fixed else after return or break warning
staging: rtl8712: Fixed else not required after return
staging: rtl8712: Fix missing blank line warning
staging: rtl8192e: rtl8192e: Remove spaces before the semicolons
staging: rtl8192e: rtl8192e: Remove unnecessary return statements
staging: rtl8192e: Remove unneeded void return
staging: rtl8192e: Fix void function return statements style
staging: rtl8712: Fix unnecessary parentheses style warning
staging: rtl8192e: Fix unnecessary space before function pointer arguments
staging: rtl8192e: Array was made static const char * const
staging: ft1000: ft1000-usb: Removed unnecessary else statement.
staging: ft1000: ft1000-usb: Removed unnecessary else statement.
staging: ft1000: ft1000-usb: Removed unnecessary parentheses.
staging: ft1000: ft1000-usb: Added new line after declarations.
staging: vt6655: Fixed C99 // comment errors in wpactl.c
staging: speakup: Fixed warning <linux/serial.h> instead of <asm/serial.h>
...
Pull arch/tile updates from Chris Metcalf:
"The only substantive pieces in this batch are some more vDSO support,
and removing the reference to &platform_bus in tile-srom.c.
The rest are minor issues reported to me"
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: add clock_gettime support to vDSO
tile: switch to using seqlocks for the vDSO time code
tile gxio: use better string copy primitive
char: tile-srom: Add real platform bus parent
Removed repeated word in comments
tilegx: Enable ARCH_SUPPORTS_ATOMIC_RMW
tile: Remove tile-specific _sinitdata and _einitdata
tile: use ARRAY_SIZE
This patch fixes a bug on hotmod removing.
After ipmi interface is removed using hotmod, kernel panic occurs when
rmmod impi_si. For example, try this:
# echo "remove,"`cat /proc/ipmi/0/params` > \
/sys/module/ipmi_si/parameters/hotmod
# rmmod ipmi_si
Then, rmmod fails with the following messages.
------------[ cut here ]------------
WARNING: CPU: 12 PID: 10819 at /mnt/repos/linux/lib/list_debug.c:53 __list_del_entry+0x63/0xd0()
CPU: 12 PID: 10819 Comm: rmmod Not tainted 3.17.0-rc1 #19
Hardware name: FUJITSU-SV PRIMERGY BX920 S2/D3030, BIOS 080015 Rev.3D81.3030 02/10/2012
Call Trace:
dump_stack+0x45/0x56
warn_slowpath_common+0x7d/0xa0
warn_slowpath_fmt+0x4c/0x50
__list_del_entry+0x63/0xd0
list_del+0xd/0x30
cleanup_one_si+0x2a/0x230 [ipmi_si]
ipmi_pnp_remove+0x15/0x20 [ipmi_si]
pnp_device_remove+0x24/0x40
__device_release_driver+0x7f/0xf0
driver_detach+0xb0/0xc0
bus_remove_driver+0x55/0xd0
driver_unregister+0x2c/0x50
pnp_unregister_driver+0x12/0x20
cleanup_ipmi_si+0xbc/0xf0 [ipmi_si]
SyS_delete_module+0x132/0x1c0
system_call_fastpath+0x16/0x1b
---[ end trace 70b4377268f85c23 ]---
list_del in cleanup_one_si() fails because the smi_info is already
removed when hotmod removing.
When ipmi interface is removed by hotmod, smi_info is removed by
cleanup_one_si(), but is is still set in drvdata. Therefore when rmmod
ipmi_si, ipmi_pnp_remove tries to remove it again and fails.
By this patch, a pointer to smi_info in drvdata is cleared when hotmod
removing so that it will be not accessed when rmmod.
changelog:
v2:
- Clear drvdata in cleanup_one_si
- Change subject
v1:
https://lkml.org/lkml/2014/9/8/741
Signed-off-by: Takao Indoh <indou.takao@jp.fujitsu.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Building ipmi on arm with gcc-4.9 results in this warning for an
allmodconfig build:
drivers/char/ipmi/ipmi_si_intf.c: In function 'ipmi_thread':
include/linux/time.h:28:5: warning: 'busy_until.tv_sec' may be used uninitialized in this function [-Wmaybe-uninitialized]
if (lhs->tv_sec > rhs->tv_sec)
^
drivers/char/ipmi/ipmi_si_intf.c:1007:18: note: 'busy_until.tv_sec' was declared here
struct timespec busy_until;
^
The warning is bogus and this case can not occur. Apparently this is a
false positive resulting from gcc getting a little smarter about
tracking assignments but not smart enough.
Marking the ipmi_thread_busy_wait function as inline gives the gcc
optimization logic enough information to figure out for itself that the
case cannot happen, which gets rid of the warning without adding any
fake initialization.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If an IPMI controller is used by the firmware and as such marked with
a reserved status, we shouldn't use it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The code to send the channel config errors was missing an error report
in one place and needed some more information in another, and had an
extraneous bit of code. Clean all that up.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The DEFINE_XENBUS_DRIVER() macro looks a bit weird and causes sparse
errors.
Replace the uses with standard structure definitions instead. This is
similar to pci and usb device registration.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Add a real platform bus device as a parent for
the srom class devices, to prevent non-platform
devices hanging from the bus root.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
as pr_* macros are more preffered over printk, so printk replaced with corresponding pr_* macros
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This driver has been functional and stable throughout the year it has spent
in the staging area. It has been patched for minor bugs, coding style issues
and improvements during this period.
This is the second submission of this move-out, after making several style
improvements, as suggested by Dan Carpenter.
Signed-off-by: Eli Billauer <eli.billauer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for the Dell Latitude E6540 which needs a different fan speed multiplier.
Signed-off-by: Steven Honeyman <stevenhoneyman@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a page isn't allocated as __GFP_MOVEABLE it won't move around, so
no need to grab a reference to lock it into place.
Discovered while reviewing page allocation handling in i915 gem.
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Before we really unregister the hwrng device, reading will get stuck if
the virtio device is reset. We should return error for reading when we
start to remove the device.
Signed-off-by: Amos Kong <akong@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
When we try to hot-remove a busy virtio-rng device from QEMU monitor,
the device can't be hot-removed. Because virtio-rng driver hangs at
wait_for_completion_killable().
This patch exits the waiting by completing have_data completion before
unregistering, resets data_avail to avoid the hwrng core use wrong
buffer bytes.
Signed-off-by: Amos Kong <akong@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
A single case of using __get_cpu_var for address calculation.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The khwrngd thread is started when a hwrng device of sufficient
quality is registered. The virtio-rng device is backed by the
hypervisor, and we trust the hypervisor to provide real entropy.
A malicious or badly-implemented hypervisor is a scenario that's
irrelevant -- such a setup is bound to cause all sorts of badness, and a
compromised hwrng is the least of the user's worries.
Given this, we might as well assume that the quality of randomness we
receive is perfectly trustworthy. Hence, we use 100% for the factor,
indicating maximum confidence in the source.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: H. Peter Anvin <hpa@linux.intel.com>
Reviewed-by: Amos Kong <akong@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Pull DRM updates from Dave Airlie:
"Like all good pull reqs this ends with a revert, so it must mean we
tested it,
[ Ed. That's _one_ way of looking at it ]
This pull is missing nouveau, Ben has been stuck trying to track down
a very longstanding bug that revealed itself due to some other
changes. I've asked him to send you a direct pull request for nouveau
once he cleans things up. I'm away until Monday so don't want to
delay things, you can make a decision on that when he sends it, I have
my phone so I can ack things just not really merge much.
It has one trivial conflict with your tree in armada_drv.c, and also
the pull request contains some component changes that are already in
your tree, the base tree from Russell went via Greg's tree already,
but some stuff still shows up in here that doesn't when I merge my
tree into yours.
Otherwise all pretty standard graphics fare, one new driver and
changes all over the place.
New drivers:
- sti kms driver for STMicroelectronics chipsets stih416 and stih407.
core:
- lots of cleanups to the drm core
- DP MST helper code merged
- universal cursor planes.
- render nodes enabled by default
panel:
- better panel interfaces
- new panel support
- non-continuous cock advertising ability
ttm:
- shrinker fixes
i915:
- hopefully ditched UMS support
- runtime pm fixes
- psr tracking and locking - now enabled by default
- userptr fixes
- backlight brightness fixes
- MST support merged
- runtime PM for dpms
- primary planes locking fixes
- gen8 hw semaphore support
- fbc fixes
- runtime PM on SOix sleep state hw.
- mmio base page flipping
- lots of vlv/chv fixes.
- universal cursor planes
radeon:
- Hawaii fixes
- display scalar support for non-fixed mode displays
- new firmware format support
- dpm on more asics by default
- GPUVM improvements
- uncached and wc GTT buffers
- BOs > visible VRAM
exynos:
- i80 interface support
- module auto-loading
- ipp driver consolidated.
armada:
- irq handling in crtc layer only
- crtc renumbering
- add component support
- DT interaction changes.
tegra:
- load as module fixes
- eDP bpp and sync polarity fixed
- DSI non-continuous clock mode support
- better support for importing buffers from nouveau
msm:
- mdp5/adq8084 v1.3 hw enablement
- devicetree clk changse
- ifc6410 board working
tda998x:
- component support
- DT documentation update
vmwgfx:
- fix compat shader namespace"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (551 commits)
Revert "drm: drop redundant drm_file->is_master"
drm/panel: simple: Use devm_gpiod_get_optional()
drm/dsi: Replace upcasting macro by function
drm/panel: ld9040: Replace upcasting macro by function
drm/exynos: dp: Modify driver to support drm_panel
drm/exynos: Move DP setup into commit()
drm/panel: simple: Add AUO B133HTN01 panel support
drm/panel: simple: Support delays in panel functions
drm/panel: simple: Add proper definition for prepare and unprepare
drm/panel: s6e8aa0: Add proper definition for prepare and unprepare
drm/panel: ld9040: Add proper definition for prepare and unprepare
drm/tegra: Add support for panel prepare and unprepare routines
drm/exynos: dsi: Add support for panel prepare and unprepare routines
drm/exynos: dpi: Add support for panel prepare and unprepare routines
drm/panel: simple: Add dummy prepare and unprepare routines
drm/panel: s6e8aa0: Add dummy prepare and unprepare routines
drm/panel: ld9040: Add dummy prepare and unprepare routines
drm/panel: Provide convenience wrapper for .get_modes()
drm/panel: add .prepare() and .unprepare() functions
drm/panel: simple: Remove simple-panel compatible
...
call, which is a superset of OpenBSD's getentropy(2) call, for use
with userspace crypto libraries such as LibreSSL. Also add the
ability to have a kernel thread to pull entropy from hardware rng
devices into /dev/random.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=wLqJ
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull randomness updates from Ted Ts'o:
"Cleanups and bug fixes to /dev/random, add a new getrandom(2) system
call, which is a superset of OpenBSD's getentropy(2) call, for use
with userspace crypto libraries such as LibreSSL.
Also add the ability to have a kernel thread to pull entropy from
hardware rng devices into /dev/random"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
hwrng: Pass entropy to add_hwgenerator_randomness() in bits, not bytes
random: limit the contribution of the hw rng to at most half
random: introduce getrandom(2) system call
hw_random: fix sparse warning (NULL vs 0 for pointer)
random: use registers from interrupted code for CPU's w/o a cycle counter
hwrng: add per-device entropy derating
hwrng: create filler thread
random: add_hwgenerator_randomness() for feeding entropy from devices
random: use an improved fast_mix() function
random: clean up interrupt entropy accounting for archs w/o cycle counters
random: only update the last_pulled time if we actually transferred entropy
random: remove unneeded hash of a portion of the entropy pool
random: always update the entropy pool under the spinlock
Pull security subsystem updates from James Morris:
"In this release:
- PKCS#7 parser for the key management subsystem from David Howells
- appoint Kees Cook as seccomp maintainer
- bugfixes and general maintenance across the subsystem"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (94 commits)
X.509: Need to export x509_request_asymmetric_key()
netlabel: shorter names for the NetLabel catmap funcs/structs
netlabel: fix the catmap walking functions
netlabel: fix the horribly broken catmap functions
netlabel: fix a problem when setting bits below the previously lowest bit
PKCS#7: X.509 certificate issuer and subject are mandatory fields in the ASN.1
tpm: simplify code by using %*phN specifier
tpm: Provide a generic means to override the chip returned timeouts
tpm: missing tpm_chip_put in tpm_get_random()
tpm: Properly clean sysfs entries in error path
tpm: Add missing tpm_do_selftest to ST33 I2C driver
PKCS#7: Use x509_request_asymmetric_key()
Revert "selinux: fix the default socket labeling in sock_graft()"
X.509: x509_request_asymmetric_keys() doesn't need string length arguments
PKCS#7: fix sparse non static symbol warning
KEYS: revert encrypted key change
ima: add support for measuring and appraising firmware
firmware_class: perform new LSM checks
security: introduce kernel_fw_from_file hook
PKCS#7: Missing inclusion of linux/err.h
...
Pull timer and time updates from Thomas Gleixner:
"A rather large update of timers, timekeeping & co
- Core timekeeping code is year-2038 safe now for 32bit machines.
Now we just need to fix all in kernel users and the gazillion of
user space interfaces which rely on timespec/timeval :)
- Better cache layout for the timekeeping internal data structures.
- Proper nanosecond based interfaces for in kernel users.
- Tree wide cleanup of code which wants nanoseconds but does hoops
and loops to convert back and forth from timespecs. Some of it
definitely belongs into the ugly code museum.
- Consolidation of the timekeeping interface zoo.
- A fast NMI safe accessor to clock monotonic for tracing. This is a
long standing request to support correlated user/kernel space
traces. With proper NTP frequency correction it's also suitable
for correlation of traces accross separate machines.
- Checkpoint/restart support for timerfd.
- A few NOHZ[_FULL] improvements in the [hr]timer code.
- Code move from kernel to kernel/time of all time* related code.
- New clocksource/event drivers from the ARM universe. I'm really
impressed that despite an architected timer in the newer chips SoC
manufacturers insist on inventing new and differently broken SoC
specific timers.
[ Ed. "Impressed"? I don't think that word means what you think it means ]
- Another round of code move from arch to drivers. Looks like most
of the legacy mess in ARM regarding timers is sorted out except for
a few obnoxious strongholds.
- The usual updates and fixlets all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (114 commits)
timekeeping: Fixup typo in update_vsyscall_old definition
clocksource: document some basic timekeeping concepts
timekeeping: Use cached ntp_tick_length when accumulating error
timekeeping: Rework frequency adjustments to work better w/ nohz
timekeeping: Minor fixup for timespec64->timespec assignment
ftrace: Provide trace clocks monotonic
timekeeping: Provide fast and NMI safe access to CLOCK_MONOTONIC
seqcount: Add raw_write_seqcount_latch()
seqcount: Provide raw_read_seqcount()
timekeeping: Use tk_read_base as argument for timekeeping_get_ns()
timekeeping: Create struct tk_read_base and use it in struct timekeeper
timekeeping: Restructure the timekeeper some more
clocksource: Get rid of cycle_last
clocksource: Move cycle_last validation to core code
clocksource: Make delta calculation a function
wireless: ath9k: Get rid of timespec conversions
drm: vmwgfx: Use nsec based interfaces
drm: i915: Use nsec based interfaces
timekeeping: Provide ktime_get_raw()
hangcheck-timer: Use ktime_get_ns()
...
rng_get_data() returns the number of bytes read from the hardware.
The entropy argument to add_hwgenerator_randomness() is passed
directly to credit_entropy_bits() so we should be passing the
number of bits, not bytes here.
Fixes: be4000bc46 "hwrng: create filler thread"
Acked-by: Torsten Duwe <duwe@suse.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
For people who don't trust a hardware RNG which can not be audited,
the changes to add support for RDSEED can be troubling since 97% or
more of the entropy will be contributed from the in-CPU hardware RNG.
We now have a in-kernel khwrngd, so for those people who do want to
implicitly trust the CPU-based system, we could create an arch-rng
hw_random driver, and allow khwrng refill the entropy pool. This
allows system administrator whether or not they trust the CPU (I
assume the NSA will trust RDRAND/RDSEED implicitly :-), and if so,
what level of entropy derating they want to use.
The reason why this is a really good idea is that if different people
use different levels of entropy derating, it will make it much more
difficult to design a backdoor'ed hwrng that can be generally
exploited in terms of the output of /dev/random when different attack
targets are using differing levels of entropy derating.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
The getrandom(2) system call was requested by the LibreSSL Portable
developers. It is analoguous to the getentropy(2) system call in
OpenBSD.
The rationale of this system call is to provide resiliance against
file descriptor exhaustion attacks, where the attacker consumes all
available file descriptors, forcing the use of the fallback code where
/dev/[u]random is not available. Since the fallback code is often not
well-tested, it is better to eliminate this potential failure mode
entirely.
The other feature provided by this new system call is the ability to
request randomness from the /dev/urandom entropy pool, but to block
until at least 128 bits of entropy has been accumulated in the
/dev/urandom entropy pool. Historically, the emphasis in the
/dev/urandom development has been to ensure that urandom pool is
initialized as quickly as possible after system boot, and preferably
before the init scripts start execution.
This is because changing /dev/urandom reads to block represents an
interface change that could potentially break userspace which is not
acceptable. In practice, on most x86 desktop and server systems, in
general the entropy pool can be initialized before it is needed (and
in modern kernels, we will printk a warning message if not). However,
on an embedded system, this may not be the case. And so with this new
interface, we can provide the functionality of blocking until the
urandom pool has been initialized. Any userspace program which uses
this new functionality must take care to assure that if it is used
during the boot process, that it will not cause the init scripts or
other portions of the system startup to hang indefinitely.
SYNOPSIS
#include <linux/random.h>
int getrandom(void *buf, size_t buflen, unsigned int flags);
DESCRIPTION
The system call getrandom() fills the buffer pointed to by buf
with up to buflen random bytes which can be used to seed user
space random number generators (i.e., DRBG's) or for other
cryptographic uses. It should not be used for Monte Carlo
simulations or other programs/algorithms which are doing
probabilistic sampling.
If the GRND_RANDOM flags bit is set, then draw from the
/dev/random pool instead of the /dev/urandom pool. The
/dev/random pool is limited based on the entropy that can be
obtained from environmental noise, so if there is insufficient
entropy, the requested number of bytes may not be returned.
If there is no entropy available at all, getrandom(2) will
either block, or return an error with errno set to EAGAIN if
the GRND_NONBLOCK bit is set in flags.
If the GRND_RANDOM bit is not set, then the /dev/urandom pool
will be used. Unlike using read(2) to fetch data from
/dev/urandom, if the urandom pool has not been sufficiently
initialized, getrandom(2) will block (or return -1 with the
errno set to EAGAIN if the GRND_NONBLOCK bit is set in flags).
The getentropy(2) system call in OpenBSD can be emulated using
the following function:
int getentropy(void *buf, size_t buflen)
{
int ret;
if (buflen > 256)
goto failure;
ret = getrandom(buf, buflen, 0);
if (ret < 0)
return ret;
if (ret == buflen)
return 0;
failure:
errno = EIO;
return -1;
}
RETURN VALUE
On success, the number of bytes that was filled in the buf is
returned. This may not be all the bytes requested by the
caller via buflen if insufficient entropy was present in the
/dev/random pool, or if the system call was interrupted by a
signal.
On error, -1 is returned, and errno is set appropriately.
ERRORS
EINVAL An invalid flag was passed to getrandom(2)
EFAULT buf is outside the accessible address space.
EAGAIN The requested entropy was not available, and
getentropy(2) would have blocked if the
GRND_NONBLOCK flag was not set.
EINTR While blocked waiting for entropy, the call was
interrupted by a signal handler; see the description
of how interrupted read(2) calls on "slow" devices
are handled with and without the SA_RESTART flag
in the signal(7) man page.
NOTES
For small requests (buflen <= 256) getrandom(2) will not
return EINTR when reading from the urandom pool once the
entropy pool has been initialized, and it will return all of
the bytes that have been requested. This is the recommended
way to use getrandom(2), and is designed for compatibility
with OpenBSD's getentropy() system call.
However, if you are using GRND_RANDOM, then getrandom(2) may
block until the entropy accounting determines that sufficient
environmental noise has been gathered such that getrandom(2)
will be operating as a NRBG instead of a DRBG for those people
who are working in the NIST SP 800-90 regime. Since it may
block for a long time, these guarantees do *not* apply. The
user may want to interrupt a hanging process using a signal,
so blocking until all of the requested bytes are returned
would be unfriendly.
For this reason, the user of getrandom(2) MUST always check
the return value, in case it returns some error, or if fewer
bytes than requested was returned. In the case of
!GRND_RANDOM and small request, the latter should never
happen, but the careful userspace code (and all crypto code
should be careful) should check for this anyway!
Finally, unless you are doing long-term key generation (and
perhaps not even then), you probably shouldn't be using
GRND_RANDOM. The cryptographic algorithms used for
/dev/urandom are quite conservative, and so should be
sufficient for all purposes. The disadvantage of GRND_RANDOM
is that it can block, and the increased complexity required to
deal with partially fulfilled getrandom(2) requests.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Zach Brown <zab@zabbo.net>
Here's the big tty / serial driver update for 3.17-rc1.
Nothing major, just a number of fixes and new features for different
serial drivers, and some more tty core fixes and documentation of the
tty locks.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlPf2C4ACgkQMUfUDdst+yllVgCgtZl/Mcr/LlxPgjsg2C1AE7nX
YJ4An3o4N112bkdGqhZ7RjAE6K/8YILx
=rPhE
-----END PGP SIGNATURE-----
Merge tag 'tty-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver update from Greg KH:
"Here's the big tty / serial driver update for 3.17-rc1.
Nothing major, just a number of fixes and new features for different
serial drivers, and some more tty core fixes and documentation of the
tty locks.
All of these have been in linux-next for a while"
* tag 'tty-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (82 commits)
tty/n_gsm.c: fix a memory leak in gsmld_open
pch_uart: don't hardcode PCI slot to get DMA device
tty: n_gsm, use setup_timer
Revert "ARC: [arcfpga] stdout-path now suffices for earlycon/console"
serial: sc16is7xx: Correct initialization of s->clk
serial: 8250_dw: Add support for deferred probing
serial: 8250_dw: Add optional reset control support
serial: st-asc: Fix overflow in baudrate calculation
serial: st-asc: Don't call BUG in asc_console_setup()
tty: serial: msm: Make of_device_id array const
tty/n_gsm.c: get gsm->num after gsm_activate_mux
serial/core: Fix too big allocation for attribute member
drivers/tty/serial: use correct type for dma_map/unmap
serial: altera_jtaguart: Fix putchar function passed to uart_console_write()
serial/uart/8250: Add tunable RX interrupt trigger I/F of FIFO buffers
Serial: allow port drivers to have a default attribute group
tty: kgdb_nmi: Automatically manage tty enable
serial: altera_jtaguart: Adpot uart_console_write()
serial: samsung: improve code clarity by defining a variable
serial: samsung: correct the case and default order in switch
...
Here's the big driver misc / char pull request for 3.17-rc1.
Lots of things in here, the thunderbolt support for Apple laptops, some
other new drivers, testing fixes, and other good things. All have been
in linux-next for a long time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlPf1LcACgkQMUfUDdst+ymaVwCgqMrKFmpduBufOSFROhxlfB5Q
ajsAoNDmIn3pgla+kj23Y5ib20aMi++s
=IdIr
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver patches from Greg KH:
"Here's the big driver misc / char pull request for 3.17-rc1.
Lots of things in here, the thunderbolt support for Apple laptops,
some other new drivers, testing fixes, and other good things. All
have been in linux-next for a long time"
* tag 'char-misc-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (119 commits)
misc: bh1780: Introduce the use of devm_kzalloc
Lattice ECP3 FPGA: Correct endianness
drivers/misc/ti-st: Load firmware from ti-connectivity directory.
dt-bindings: extcon: Add support for SM5502 MUIC device
extcon: sm5502: Change internal hardware switch according to cable type
extcon: sm5502: Detect cable state after completing platform booting
extcon: sm5502: Add support new SM5502 extcon device driver
extcon: arizona: Get MICVDD against extcon device
extcon: Remove unnecessary OOM messages
misc: vexpress: Fix sparse non static symbol warnings
mei: drop unused hw dependent fw status functions
misc: bh1770glc: Use managed functions
pcmcia: remove DEFINE_PCI_DEVICE_TABLE usage
misc: remove DEFINE_PCI_DEVICE_TABLE usage
ipack: Replace DEFINE_PCI_DEVICE_TABLE macro use
drivers/char/dsp56k.c: drop check for negativity of unsigned parameter
mei: fix return value on disconnect timeout
mei: don't schedule suspend in pm idle
mei: start disconnect request timer consistently
mei: reset client connection state on timeout
...
The VFS layer handles those in the very same way, if unset. No need for
additional stubs.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Instead of looping by ourselves we may use %*phN specifier to dump a small
buffer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
[ PHuewe: removed now unused variable i ]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Some Atmel TPMs provide completely wrong timeouts from their
TPM_CAP_PROP_TIS_TIMEOUT query. This patch detects that and returns
new correct values via a DID/VID table in the TIS driver.
Tested on ARM using an AT97SC3204T FW version 37.16
Cc: <stable@vger.kernel.org>
[PHuewe: without this fix these 'broken' Atmel TPMs won't function on
older kernels]
Signed-off-by: "Berg, Christopher" <Christopher.Berg@atmel.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Regression in 41ab999c. Call to tpm_chip_put is missing. This
will cause TPM device driver not to unload if tmp_get_random()
is called.
Cc: <stable@vger.kernel.org> # 3.7+
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Properly clean the sysfs entries in the error path
Cc: <stable@vger.kernel.org>
Reported-by: Dmitry Kasatkin <dmitry.kasatkin@gmail.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Most device drivers do call 'tpm_do_selftest' which executes a
TPM_ContinueSelfTest. tpm_i2c_stm_st33 is just pointlessly different,
I think it is bug.
These days we have the general assumption that the TPM is usable by
the kernel immediately after the driver is finished, so we can no
longer defer the mandatory self test to userspace.
Cc: <stable@vger.kernel.org> # 3.12+
Reported-by: Richard Marciel <rmaciel@linux.vnet.ibm.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
This reverts commit e052dbf554.
Now that we use the virtio ->scan() function to register with the hwrng
core, we will not get read requests till probe is successfully finished.
So revert the workaround we had in place to refuse read requests while
we were not yet setup completely.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Instead of calling hwrng_register() in the probe routing, call it in the
scan routine. This ensures that when hwrng_register() is successful,
and it requests a few random bytes to seed the kernel's pool at init,
we're ready to service that request.
This will also enable us to remove the workaround added previously to
check whether probe was completed, and only then ask for data from the
host. The revert follows in the next commit.
There's a slight behaviour change here on unsuccessful hwrng_register().
Previously, when hwrng_register() failed, the probe() routine would
fail, and the vqs would be torn down, and driver would be marked not
initialized. Now, the vqs will remain initialized, driver would be
marked initialized as well, but won't be available in the list of RNGs
available to hwrng core. To fix the failures, the procedure remains the
same, i.e. unload and re-load the module, and hope things succeed the
next time around.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Re-arrange the elements of the virtrng_info struct to pack it better.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
vdev is unused in struct virtrng_info, remove it.
CC: Amos Kong <akong@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Fix checkpatch warning:
WARNING: debugfs_remove_recursive(NULL) is safe this check is probably not required
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: virtualization@lists.linux-foundation.org
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
There is no point in having a S390 private implementation and there is
no point in using the raw monotonic time. The NTP freqeuency
adjustment of CLOCK_MONOTONIC is really not doing any harm for the
hang check timer.
Use ktime_get_ns() for everything and get rid of the timespec
conversions.
V2: Drop the raw monotonic and the S390 special case
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=8rgT
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull /dev/random fix from Ted Ts'o:
"Fix a BUG splat found by trinity"
* tag 'random_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: check for increase of entropy_count because of signed conversion
Pull crypto fixes from Herbert Xu:
"This push fixes a boot hang in virt guests when the virtio RNG is
enabled"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
hwrng: virtio - ensure reads happen after successful probe
hwrng: fetch randomness only after device init
The expression entropy_count -= ibytes << (ENTROPY_SHIFT + 3) could
actually increase entropy_count if during assignment of the unsigned
expression on the RHS (mind the -=) we reduce the value modulo
2^width(int) and assign it to entropy_count. Trinity found this.
[ Commit modified by tytso to add an additional safety check for a
negative entropy_count -- which should never happen, and to also add
an additional paranoia check to prevent overly large count values to
be passed into urandom_read(). ]
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
[linux-3.16-rc5/drivers/char/dsp56k.c:386]: (style) Checking if unsigned
variable 'arg' is less than zero.
Source code is
if (arg > 31 || arg < 0)
return -EINVAL;
But
static long dsp56k_ioctl(struct file *file, unsigned int cmd,
unsigned long arg)
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=80411
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Andrey Utkin <andrey.krieger.utkin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For CPU's that don't have a cycle counter, or something equivalent
which can be used for random_get_entropy(), random_get_entropy() will
always return 0. In that case, substitute with the saved interrupt
registers to add a bit more unpredictability.
Some folks have suggested hashing all of the registers
unconditionally, but this would increase the overhead of
add_interrupt_randomness() by at least an order of magnitude, and this
would very likely be unacceptable.
The changes in this commit have been benchmarked as mostly unaffecting
the overhead of add_interrupt_randomness() if the entropy counter is
present, and doubling the overhead if it is not present.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: Jörn Engel <joern@logfs.org>
This patch introduces a derating factor to struct hwrng for
the random bits going into the kernel input pool, and a common
default derating for drivers which do not specify one.
Signed-off-by: Torsten Duwe <duwe@suse.de>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Acked-by: H. Peter Anvin <hpa@zytor.com>
This can be viewed as the in-kernel equivalent of hwrngd;
like FUSE it is a good thing to have a mechanism in user land,
but for some reasons (simplicity, secrecy, integrity, speed)
it may be better to have it in kernel space.
This patch creates a thread once a hwrng registers, and uses
the previously established add_hwgenerator_randomness() to feed
its data to the input pool as long as needed. A derating factor
is used to bias the entropy estimation and to disable this
mechanism entirely when set to zero.
Signed-off-by: Torsten Duwe <duwe@suse.de>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Acked-by: H. Peter Anvin <hpa@zytor.com>
This patch adds an interface to the random pool for feeding entropy
in-kernel.
Signed-off-by: Torsten Duwe <duwe@suse.de>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Use more efficient fast_mix() function. Thanks to George Spelvin for
doing the leg work to find a more efficient mixing function.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: George Spelvin <linux@horizon.com>
For architectures that don't have cycle counters, the algorithm for
deciding when to avoid giving entropy credit due to back-to-back timer
interrupts didn't make any sense, since we were checking every 64
interrupts. Change it so that we only give an entropy credit if the
majority of the interrupts are not based on the timer.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: George Spelvin <linux@horizon.com>
In xfer_secondary_pull(), check to make sure we need to pull from the
secondary pool before checking and potentially updating the
last_pulled time.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: George Spelvin <linux@horizon.com>
We previously extracted a portion of the entropy pool in
mix_pool_bytes() and hashed it in to avoid racing CPU's from returning
duplicate random values. Now that we are using a spinlock to prevent
this from happening, this is no longer necessary. So remove it, to
simplify the code a bit.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: George Spelvin <linux@horizon.com>
Instead of using lockless techniques introduced in commit
902c098a36, use spin_trylock to try to grab entropy pool's lock. If
we can't get the lock, then just try again on the next interrupt.
Based on discussions with George Spelvin.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: George Spelvin <linux@horizon.com>
The hwrng core asks for random data in the hwrng_register() call itself
from commit d9e7972619. This doesn't play well with virtio -- the
DRIVER_OK bit is only set by virtio core on a successful probe, and
we're not yet out of our probe routine when this call is made. This
causes the host to not acknowledge any requests we put in the virtqueue,
and the insmod or kernel boot process just waits for data to arrive from
the host, which never happens.
CC: Kees Cook <keescook@chromium.org>
CC: Jason Cooper <jason@lakedaemon.net>
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: <stable@vger.kernel.org> # For v3.15+
Reviewed-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Commit d9e7972619 "hwrng: add randomness to system from rng sources"
added a call to rng_get_data() from the hwrng_register() function.
However, some rng devices need initialization before data can be read
from them.
This commit makes the call to rng_get_data() depend on no init fn
pointer being registered by the device. If an init function is
registered, this call is made after device init.
CC: Kees Cook <keescook@chromium.org>
CC: Jason Cooper <jason@lakedaemon.net>
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: <stable@vger.kernel.org> # For v3.15+
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This resolves a number of merge issues with changes in this tree and
Linus's tree at the same time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_port_close_start() already validates the port counts and issues
a diagnostic if validation fails.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since at least before 2.6.30, it has not been possible to observe
a hung up file pointer in a tty driver's open() method unless/until
the driver open() releases the tty_lock() (eg., before blocking).
This is because tty_open() adds the file pointer while holding
the tty_lock() _and_ doesn't release the lock until after calling
the tty driver's open() method. [ Before tty_lock(), this was
lock_kernel(). ]
Since __tty_hangup() first waits on the tty_lock() before
enumerating and hanging up the open file pointers, either
__tty_hangup() will wait for the tty_lock() or tty_open() will
not yet have added the file pointer. For example,
CPU 0 | CPU 1
|
tty_open | __tty_hangup
.. | ..
tty_lock | ..
tty_reopen | tty_lock / blocks
.. |
tty_add_file(tty, filp) |
.. |
tty->ops->open(tty, filp) |
tty_port_open |
tty_port_block_til_ready |
.. |
while (1) |
.. |
tty_unlock | / unblocks
schedule | for each filp on tty->tty_files
| f_ops = tty_hung_up_fops;
| ..
| tty_unlock
tty_lock |
.. |
tty_unlock |
Note that since tty_port_block_til_ready() and similar drop
the tty_lock while blocking, when woken, the file pointer
must then be tested for having been hung up.
Also, fix bit-rotted drivers that used extra_count to track the
port->count bump.
CC: Mikael Starvik <starvik@axis.com>
CC: Samuel Ortiz <samuel@sortiz.org>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return -ENOMEM instead of success if ioremap() fails.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This makes sure a format string cannot accidentally leak into a device name.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f36fdb9f02 (i8k: Force SMM to run on CPU 0) adds support
for multi-core CPUs to the driver. Unfortunately, that causes it
to fail loading if compiled without SMP support, at least on
32 bit kernels. Kernel log shows "i8k: unable to get SMM Dell
signature", and function i8k_smm is found to return -EINVAL.
Testing revealed that the culprit is the missing return value check
of set_cpus_allowed_ptr.
Fixes: f36fdb9f02 (i8k: Force SMM to run on CPU 0)
Reported-by: Jim Bos <jim876@xs4all.nl>
Tested-by: Jim Bos <jim876@xs4all.nl>
Cc: stable@vger.kernel.org # 3.14+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Andreas Mohr <andi@lisas.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both systems need non-standard parameters for fan multiplier
and maximum fan speed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Andreas Mohr <andi@lisas.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Newer Dell systems provide more granular fan speed selection.
Add support for it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Andreas Mohr <andi@lisas.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Labels are known to be wrong for several Dell laptops.
For example, a single fan may be shown as right fan when in reality
it sits on the left side of the chassis. Drop all labels to avoid
such inaccuracies. Users can select labels in the sensors configuration
file instead if desired.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Andreas Mohr <andi@lisas.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 0fb7a01af5 "random: simplify accounting code", introduced in
v3.15, has a very nasty accounting problem when the entropy pool has
has fewer bytes of entropy than the number of requested reserved
bytes. In that case, "have_bytes - reserved" goes negative, and since
size_t is unsigned, the expression:
ibytes = min_t(size_t, ibytes, have_bytes - reserved);
... does not do the right thing. This is rather bad, because it
defeats the catastrophic reseeding feature in the
xfer_secondary_pool() path.
It also can cause the "BUG: spinlock trylock failure on UP" for some
kernel configurations when prandom_reseed() calls get_random_bytes()
in the early init, since when the entropy count gets corrupted,
credit_entropy_bits() erroneously believes that the nonblocking pool
has been fully initialized (when in fact it is not), and so it calls
prandom_reseed(true) recursively leading to the spinlock BUG.
The logic is *not* the same it was originally, but in the cases where
it matters, the behavior is the same, and the resulting code is
hopefully easier to read and understand.
Fixes: 0fb7a01af5 "random: simplify accounting code"
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: Greg Price <price@mit.edu>
Cc: stable@vger.kernel.org #v3.15
Pull vfs updates from Al Viro:
"This the bunch that sat in -next + lock_parent() fix. This is the
minimal set; there's more pending stuff.
In particular, I really hope to get acct.c fixes merged this cycle -
we need that to deal sanely with delayed-mntput stuff. In the next
pile, hopefully - that series is fairly short and localized
(kernel/acct.c, fs/super.c and fs/namespace.c). In this pile: more
iov_iter work. Most of prereqs for ->splice_write with sane locking
order are there and Kent's dio rewrite would also fit nicely on top of
this pile"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (70 commits)
lock_parent: don't step on stale ->d_parent of all-but-freed one
kill generic_file_splice_write()
ceph: switch to iter_file_splice_write()
shmem: switch to iter_file_splice_write()
nfs: switch to iter_splice_write_file()
fs/splice.c: remove unneeded exports
ocfs2: switch to iter_file_splice_write()
->splice_write() via ->write_iter()
bio_vec-backed iov_iter
optimize copy_page_{to,from}_iter()
bury generic_file_aio_{read,write}
lustre: get rid of messing with iovecs
ceph: switch to ->write_iter()
ceph_sync_direct_write: stop poking into iov_iter guts
ceph_sync_read: stop poking into iov_iter guts
new helper: copy_page_from_iter()
fuse: switch to ->write_iter()
btrfs: switch to ->write_iter()
ocfs2: switch to ->write_iter()
xfs: switch to ->write_iter()
...
path, which I refuse to CC stable since (1) I discovered it myself, and
(2) it's been there forever with no reports.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YCNa
-----END PGP SIGNATURE-----
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio updates from Rusty Russell:
"Main excitement is a virtio_scsi fix for alloc holding spinlock on the
abort path, which I refuse to CC stable since (1) I discovered it
myself, and (2) it's been there forever with no reports"
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio_scsi: don't call virtqueue_add_sgs(... GFP_NOIO) holding spinlock.
virtio-rng: fixes for device registration/unregistration
virtio-rng: fix boot with virtio-rng device
virtio-rng: support multiple virtio-rng devices
virtio_ccw: introduce device_lost in virtio_ccw_device
virtio: virtio_break_device() to mark all virtqueues broken.
This typedef is unnecessary and should just be removed.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- ACPICA update to upstream version 20140424. That includes a
number of fixes and improvements related to things like GPE
handling, table loading, headers, memory mapping and unmapping,
DSDT/SSDT overriding, and the Unload() operator. The acpidump
utility from upstream ACPICA is included too. From Bob Moore,
Lv Zheng, David Box, David Binderman, and Colin Ian King.
- Fixes and cleanups related to ACPI video and backlight interfaces
from Hans de Goede. That includes blacklist entries for some new
machines and using native backlight by default.
- ACPI device enumeration changes to create platform devices
rather than PNP devices for ACPI device objects with _HID by
default. PNP devices will still be created for the ACPI device
object with device IDs corresponding to real PNP devices, so
that change should not break things left and right, and we're
expecting to see more and more ACPI-enumerated platform devices
in the future. From Zhang Rui and Rafael J Wysocki.
- Updates for the ACPI LPSS (Low-Power Subsystem) driver allowing
it to handle system suspend/resume on Asus T100 correctly.
From Heikki Krogerus and Rafael J Wysocki.
- PM core update introducing a mechanism to allow runtime-suspended
devices to stay suspended over system suspend/resume transitions
if certain additional conditions related to coordination within
device hierarchy are met. Related PM documentation update and
ACPI PM domain support for the new feature. From Rafael J Wysocki.
- Fixes and improvements related to the "freeze" sleep state. They
affect several places including cpuidle, PM core, ACPI core, and
the ACPI battery driver. From Rafael J Wysocki and Zhang Rui.
- Miscellaneous fixes and updates of the ACPI core from Aaron Lu,
Bjørn Mork, Hanjun Guo, Lan Tianyu, and Rafael J Wysocki.
- Fixes and cleanups for the ACPI processor and ACPI PAD (Processor
Aggregator Device) drivers from Baoquan He, Manuel Schölling,
Tony Camuso, and Toshi Kani.
- System suspend/resume optimization in the ACPI battery driver from
Lan Tianyu.
- OPP (Operating Performance Points) subsystem updates from
Chander Kashyap, Mark Brown, and Nishanth Menon.
- cpufreq core fixes, updates and cleanups from Srivatsa S Bhat,
Stratos Karafotis, and Viresh Kumar.
- Updates, fixes and cleanups for the Tegra, powernow-k8, imx6q,
s5pv210, nforce2, and powernv cpufreq drivers from Brian Norris,
Jingoo Han, Paul Bolle, Philipp Zabel, Stratos Karafotis, and
Viresh Kumar.
- intel_pstate driver fixes and cleanups from Dirk Brandewie,
Doug Smythies, and Stratos Karafotis.
- Enabling the big.LITTLE cpufreq driver on arm64 from Mark Brown.
- Fix for the cpuidle menu governor from Chander Kashyap.
- New ARM clps711x cpuidle driver from Alexander Shiyan.
- Hibernate core fixes and cleanups from Chen Gang, Dan Carpenter,
Fabian Frederick, Pali Rohár, and Sebastian Capella.
- Intel RAPL (Running Average Power Limit) driver updates from
Jacob Pan.
- PNP subsystem updates from Bjorn Helgaas and Fabian Frederick.
- devfreq core updates from Chanwoo Choi and Paul Bolle.
- devfreq updates for exynos4 and exynos5 from Chanwoo Choi and
Bartlomiej Zolnierkiewicz.
- turbostat tool fix from Jean Delvare.
- cpupower tool updates from Prarit Bhargava, Ramkumar Ramachandra
and Thomas Renninger.
- New ACPI ec_access.c tool for poking at the EC in a safe way
from Thomas Renninger.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=tpdF
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm into next
Pull ACPI and power management updates from Rafael Wysocki:
"ACPICA is the leader this time (63 commits), followed by cpufreq (28
commits), devfreq (15 commits), system suspend/hibernation (12
commits), ACPI video and ACPI device enumeration (10 commits each).
We have no major new features this time, but there are a few
significant changes of how things work. The most visible one will
probably be that we are now going to create platform devices rather
than PNP devices by default for ACPI device objects with _HID. That
was long overdue and will be really necessary to be able to use the
same drivers for the same hardware blocks on ACPI and DT-based systems
going forward. We're not expecting fallout from this one (as usual),
but it's something to watch nevertheless.
The second change having a chance to be visible is that ACPI video
will now default to using native backlight rather than the ACPI
backlight interface which should generally help systems with broken
Win8 BIOSes. We're hoping that all problems with the native backlight
handling that we had previously have been addressed and we are in a
good enough shape to flip the default, but this change should be easy
enough to revert if need be.
In addition to that, the system suspend core has a new mechanism to
allow runtime-suspended devices to stay suspended throughout system
suspend/resume transitions if some extra conditions are met
(generally, they are related to coordination within device hierarchy).
However, enabling this feature requires cooperation from the bus type
layer and for now it has only been implemented for the ACPI PM domain
(used by ACPI-enumerated platform devices mostly today).
Also, the acpidump utility that was previously shipped as a separate
tool will now be provided by the upstream ACPICA along with the rest
of ACPICA code, which will allow it to be more up to date and better
supported, and we have one new cpuidle driver (ARM clps711x).
The rest is improvements related to certain specific use cases,
cleanups and fixes all over the place.
Specifics:
- ACPICA update to upstream version 20140424. That includes a number
of fixes and improvements related to things like GPE handling,
table loading, headers, memory mapping and unmapping, DSDT/SSDT
overriding, and the Unload() operator. The acpidump utility from
upstream ACPICA is included too. From Bob Moore, Lv Zheng, David
Box, David Binderman, and Colin Ian King.
- Fixes and cleanups related to ACPI video and backlight interfaces
from Hans de Goede. That includes blacklist entries for some new
machines and using native backlight by default.
- ACPI device enumeration changes to create platform devices rather
than PNP devices for ACPI device objects with _HID by default. PNP
devices will still be created for the ACPI device object with
device IDs corresponding to real PNP devices, so that change should
not break things left and right, and we're expecting to see more
and more ACPI-enumerated platform devices in the future. From
Zhang Rui and Rafael J Wysocki.
- Updates for the ACPI LPSS (Low-Power Subsystem) driver allowing it
to handle system suspend/resume on Asus T100 correctly. From
Heikki Krogerus and Rafael J Wysocki.
- PM core update introducing a mechanism to allow runtime-suspended
devices to stay suspended over system suspend/resume transitions if
certain additional conditions related to coordination within device
hierarchy are met. Related PM documentation update and ACPI PM
domain support for the new feature. From Rafael J Wysocki.
- Fixes and improvements related to the "freeze" sleep state. They
affect several places including cpuidle, PM core, ACPI core, and
the ACPI battery driver. From Rafael J Wysocki and Zhang Rui.
- Miscellaneous fixes and updates of the ACPI core from Aaron Lu,
Bjørn Mork, Hanjun Guo, Lan Tianyu, and Rafael J Wysocki.
- Fixes and cleanups for the ACPI processor and ACPI PAD (Processor
Aggregator Device) drivers from Baoquan He, Manuel Schölling, Tony
Camuso, and Toshi Kani.
- System suspend/resume optimization in the ACPI battery driver from
Lan Tianyu.
- OPP (Operating Performance Points) subsystem updates from Chander
Kashyap, Mark Brown, and Nishanth Menon.
- cpufreq core fixes, updates and cleanups from Srivatsa S Bhat,
Stratos Karafotis, and Viresh Kumar.
- Updates, fixes and cleanups for the Tegra, powernow-k8, imx6q,
s5pv210, nforce2, and powernv cpufreq drivers from Brian Norris,
Jingoo Han, Paul Bolle, Philipp Zabel, Stratos Karafotis, and
Viresh Kumar.
- intel_pstate driver fixes and cleanups from Dirk Brandewie, Doug
Smythies, and Stratos Karafotis.
- Enabling the big.LITTLE cpufreq driver on arm64 from Mark Brown.
- Fix for the cpuidle menu governor from Chander Kashyap.
- New ARM clps711x cpuidle driver from Alexander Shiyan.
- Hibernate core fixes and cleanups from Chen Gang, Dan Carpenter,
Fabian Frederick, Pali Rohár, and Sebastian Capella.
- Intel RAPL (Running Average Power Limit) driver updates from Jacob
Pan.
- PNP subsystem updates from Bjorn Helgaas and Fabian Frederick.
- devfreq core updates from Chanwoo Choi and Paul Bolle.
- devfreq updates for exynos4 and exynos5 from Chanwoo Choi and
Bartlomiej Zolnierkiewicz.
- turbostat tool fix from Jean Delvare.
- cpupower tool updates from Prarit Bhargava, Ramkumar Ramachandra
and Thomas Renninger.
- New ACPI ec_access.c tool for poking at the EC in a safe way from
Thomas Renninger"
* tag 'pm+acpi-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (187 commits)
ACPICA: Namespace: Remove _PRP method support.
intel_pstate: Improve initial busy calculation
intel_pstate: add sample time scaling
intel_pstate: Correct rounding in busy calculation
intel_pstate: Remove C0 tracking
PM / hibernate: fixed typo in comment
ACPI: Fix x86 regression related to early mapping size limitation
ACPICA: Tables: Add mechanism to control early table checksum verification.
ACPI / scan: use platform bus type by default for _HID enumeration
ACPI / scan: always register ACPI LPSS scan handler
ACPI / scan: always register memory hotplug scan handler
ACPI / scan: always register container scan handler
ACPI / scan: Change the meaning of missing .attach() in scan handlers
ACPI / scan: introduce platform_id device PNP type flag
ACPI / scan: drop unsupported serial IDs from PNP ACPI scan handler ID list
ACPI / scan: drop IDs that do not comply with the ACPI PNP ID rule
ACPI / PNP: use device ID list for PNPACPI device enumeration
ACPI / scan: .match() callback for ACPI scan handlers
ACPI / battery: wakeup the system only when necessary
power_supply: allow power supply devices registered w/o wakeup source
...
* acpica: (63 commits)
ACPICA: Namespace: Remove _PRP method support.
ACPI: Fix x86 regression related to early mapping size limitation
ACPICA: Tables: Add mechanism to control early table checksum verification.
ACPICA: acpidump: Fix repetitive table dump in -n mode.
ACPI: Clean up acpi_os_map/unmap_memory() to eliminate __iomem.
ACPICA: Clean up redudant definitions already defined elsewhere
ACPICA: Linux headers: Add <asm/acenv.h> to remove mis-ordered inclusion of <asm/acpi.h>
ACPICA: Linux headers: Add <acpi/platform/aclinuxex.h>
ACPICA: Linux headers: Remove ACPI_PREEMPTION_POINT() due to no usages.
ACPICA: Update version to 20140424.
ACPICA: Comment/format update, no functional change.
ACPICA: Events: Update GPE handling and initialization code.
ACPICA: Remove extraneous error message for large number of GPEs.
ACPICA: Tables: Remove old mechanism to validate if XSDT contains NULL entries.
ACPICA: Tables: Add new mechanism to skip NULL entries in RSDT and XSDT.
ACPICA: acpidump: Add support to force using RSDT.
ACPICA: Back port of improvements on exception code.
ACPICA: Back port of _PRP update.
ACPICA: acpidump: Fix truncated RSDP signature validation.
ACPICA: Linux header: Add support for stubbed externals.
...
Pull scheduler updates from Ingo Molnar:
"The main scheduling related changes in this cycle were:
- various sched/numa updates, for better performance
- tree wide cleanup of open coded nice levels
- nohz fix related to rq->nr_running use
- cpuidle changes and continued consolidation to improve the
kernel/sched/idle.c high level idle scheduling logic. As part of
this effort I pulled cpuidle driver changes from Rafael as well.
- standardized idle polling amongst architectures
- continued work on preparing better power/energy aware scheduling
- sched/rt updates
- misc fixlets and cleanups"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (49 commits)
sched/numa: Decay ->wakee_flips instead of zeroing
sched/numa: Update migrate_improves/degrades_locality()
sched/numa: Allow task switch if load imbalance improves
sched/rt: Fix 'struct sched_dl_entity' and dl_task_time() comments, to match the current upstream code
sched: Consolidate open coded implementations of nice level frobbing into nice_to_rlimit() and rlimit_to_nice()
sched: Initialize rq->age_stamp on processor start
sched, nohz: Change rq->nr_running to always use wrappers
sched: Fix the rq->next_balance logic in rebalance_domains() and idle_balance()
sched: Use clamp() and clamp_val() to make sys_nice() more readable
sched: Do not zero sg->cpumask and sg->sgp->power in build_sched_groups()
sched/numa: Fix initialization of sched_domain_topology for NUMA
sched: Call select_idle_sibling() when not affine_sd
sched: Simplify return logic in sched_read_attr()
sched: Simplify return logic in sched_copy_attr()
sched: Fix exec_start/task_hot on migrated tasks
arm64: Remove TIF_POLLING_NRFLAG
metag: Remove TIF_POLLING_NRFLAG
sched/idle: Make cpuidle_idle_call() void
sched/idle: Reflow cpuidle_idle_call()
sched/idle: Delay clearing the polling bit
...
Here is the big char / misc driver updates for 3.16-rc1.
Lots of different driver updates for a variety of different drivers and
minor driver subsystems.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlONWI8ACgkQMUfUDdst+ykvQACdGxTChdEU7edElDAXeelVmu8v
D1UAoLDvqwUsN7t5v+WG2wkOvhf5MEA7
=tVMP
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc into next
Pull char/misc driver patches from Greg KH:
"Here is the big char / misc driver update for 3.16-rc1.
Lots of different driver updates for a variety of different drivers
and minor driver subsystems.
All have been in linux-next with no reported issues"
* tag 'char-misc-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (79 commits)
hv: use correct order when freeing monitor_pages
spmi: of: fixup generic SPMI devicetree binding example
applicom: dereferencing NULL on error path
misc: genwqe: fix uninitialized return value in genwqe_free_sync_sgl()
miscdevice.h: Simple syntax fix to make pointers consistent.
MAINTAINERS: Add miscdevice.h to file list for char/misc drivers.
mcb: Add support for shared PCI IRQs
drivers: Remove duplicate conditionally included subdirs
misc: atmel_pwm: only build for supported platforms
mei: me: move probe quirk to cfg structure
mei: add per device configuration
mei: me: read H_CSR after asserting reset
mei: me: drop harmful wait optimization
mei: me: fix hw ready reset flow
mei: fix memory leak of mei_clients array
uio: fix vma io range check in mmap
drivers: uio_dmem_genirq: Fix memory leak in uio_dmem_genirq_probe()
w1: do not unlock unheld list_mutex in __w1_remove_master_device()
w1: optional bundling of netlink kernel replies
connector: allow multiple messages to be sent in one packet
...
Pull block core updates from Jens Axboe:
"It's a big(ish) round this time, lots of development effort has gone
into blk-mq in the last 3 months. Generally we're heading to where
3.16 will be a feature complete and performant blk-mq. scsi-mq is
progressing nicely and will hopefully be in 3.17. A nvme port is in
progress, and the Micron pci-e flash driver, mtip32xx, is converted
and will be sent in with the driver pull request for 3.16.
This pull request contains:
- Lots of prep and support patches for scsi-mq have been integrated.
All from Christoph.
- API and code cleanups for blk-mq from Christoph.
- Lots of good corner case and error handling cleanup fixes for
blk-mq from Ming Lei.
- A flew of blk-mq updates from me:
* Provide strict mappings so that the driver can rely on the CPU
to queue mapping. This enables optimizations in the driver.
* Provided a bitmap tagging instead of percpu_ida, which never
really worked well for blk-mq. percpu_ida relies on the fact
that we have a lot more tags available than we really need, it
fails miserably for cases where we exhaust (or are close to
exhausting) the tag space.
* Provide sane support for shared tag maps, as utilized by scsi-mq
* Various fixes for IO timeouts.
* API cleanups, and lots of perf tweaks and optimizations.
- Remove 'buffer' from struct request. This is ancient code, from
when requests were always virtually mapped. Kill it, to reclaim
some space in struct request. From me.
- Remove 'magic' from blk_plug. Since we store these on the stack
and since we've never caught any actual bugs with this, lets just
get rid of it. From me.
- Only call part_in_flight() once for IO completion, as includes two
atomic reads. Hopefully we'll get a better implementation soon, as
the part IO stats are now one of the more expensive parts of doing
IO on blk-mq. From me.
- File migration of block code from {mm,fs}/ to block/. This
includes bio.c, bio-integrity.c, bounce.c, and ioprio.c. From me,
from a discussion on lkml.
That should describe the meat of the pull request. Also has various
little fixes and cleanups from Dave Jones, Shaohua Li, Duan Jiong,
Fengguang Wu, Fabian Frederick, Randy Dunlap, Robert Elliott, and Sam
Bradshaw"
* 'for-3.16/core' of git://git.kernel.dk/linux-block: (100 commits)
blk-mq: push IPI or local end_io decision to __blk_mq_complete_request()
blk-mq: remember to start timeout handler for direct queue
block: ensure that the timer is always added
blk-mq: blk_mq_unregister_hctx() can be static
blk-mq: make the sysfs mq/ layout reflect current mappings
blk-mq: blk_mq_tag_to_rq should handle flush request
block: remove dead code in scsi_ioctl:blk_verify_command
blk-mq: request initialization optimizations
block: add queue flag for disabling SG merging
block: remove 'magic' from struct blk_plug
blk-mq: remove alloc_hctx and free_hctx methods
blk-mq: add file comments and update copyright notices
blk-mq: remove blk_mq_alloc_request_pinned
blk-mq: do not use blk_mq_alloc_request_pinned in blk_mq_map_request
blk-mq: remove blk_mq_wait_for_tags
blk-mq: initialize request in __blk_mq_alloc_request
blk-mq: merge blk_mq_alloc_reserved_request into blk_mq_alloc_request
blk-mq: add helper to insert requests from irq context
blk-mq: remove stale comment for blk_mq_complete_request()
blk-mq: allow non-softirq completions
...
This is a static checker fix. The "dev" variable is always NULL after
the while statement so we would be dereferencing a NULL pointer here.
Fixes: 819a3eba42 ('[PATCH] applicom: fix error handling')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ACPICA doesn't include protections around address space checking, Linux
build tests always complain increased sparse warnings around ACPICA
internal acpi_os_map/unmap_memory() invocations. This patch tries to fix
this issue permanently.
There are 2 choices left for us to solve this issue:
1. Add __iomem address space awareness into ACPICA.
2. Remove sparse checker of __iomem from ACPICA source code.
This patch chooses solution 2, because:
1. Most of the acpi_os_map/unmap_memory() invocations are used for ACPICA.
table mappings, which in fact are not IO addresses.
2. The only IO addresses usage is for "system memory space" mapping code in:
drivers/acpi/acpica/exregion.c
drivers/acpi/acpica/evrgnini.c
drivers/acpi/acpica/exregion.c
The mapped address is accessed in the handler of "system memory space"
- acpi_ex_system_memory_space_handler(). This function in fact can be
changed to invoke acpi_os_read/write_memory() so that __iomem can
always be type-casted in the OSL layer.
According to the above investigation, we drew the following conclusion:
It is not a good idea to introduce __iomem address space awareness into
ACPICA mostly in order to protect non-IO addresses.
We can simply remove __iomem for acpi_os_map/unmap_memory() to remove
__iomem checker for ACPICA code. Then we need to enforce external usages
to invoke other APIs that are aware of __iomem address space.
The external usages are:
drivers/acpi/apei/einj.c
drivers/acpi/acpi_extlog.c
drivers/char/tpm/tpm_acpi.c
drivers/acpi/nvs.c
This patch thus performs cleanups in this way:
1. Add acpi_os_map/unmap_iomem() to be invoked by non-ACPICA code.
2. Remove __iomem from acpi_os_map/unmap_memory().
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
last merge window.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=ZFSi
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull /dev/random fix from Ted Ts'o:
"This fixes a BUG_ON-causing regression that was introduced during the
last merge window"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: fix BUG_ON caused by accounting simplification
There are several fixes in this patch (mostly because it's hard
splitting them up):
- Revert the name field in struct hwrng back to 'const'. Also, don't
do an extra kmalloc for the name - just wasteful.
- Deal with allocation failures properly.
- Use IDA to allocate device number instead of brute forcing one.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Commit "virtio-rng: support multiple virtio-rng devices" has broken
boot with a virtio-rng device because the 'init' callback of the
virtio-rng device was left unitialized to garbage, and got called
by the hwrng infrastructure, killing the guest on boot.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Fixes: 08e53fbdb8
Commit ee1de406ba ("random: simplify accounting logic") simplified
things too much, in that it allows the following to trigger an
overflow that results in a BUG_ON crash:
dd if=/dev/urandom of=/dev/zero bs=67108707 count=1
Thanks to Peter Zihlstra for discovering the crash, and Hannes
Frederic for analyizing the root cause.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reported-by: Peter Zijlstra <peterz@infradead.org>
Reported-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Greg Price <price@mit.edu>
Current hwrng core supports to register multiple hwrng devices,
and there is only one device really works in the same time.
QEMU alsu supports to have multiple virtio-rng backends.
This patch changes virtio-rng driver to support multiple
virtio-rng devices.
]# cat /sys/class/misc/hw_random/rng_available
virtio_rng.0 virtio_rng.1
]# cat /sys/class/misc/hw_random/rng_current
virtio_rng.0
]# echo -n virtio_rng.1 > /sys/class/misc/hw_random/rng_current
]# dd if=/dev/hwrng of=/dev/null
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This patch moves data allocated using kzalloc to managed data allocated
using devm_kzalloc and cleans now unnecessary kfrees in probe and remove
functions. The NULL assignment to np->units is removed as there is no
interaction between this field and sun4v_hvapi_unregister. Also, the
labels out_free_units and out_free are removed as they are no longer
required.
The following Coccinelle semantic patch was used for making the change:
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e, e1, e2;
@@
probefn(struct platform_device *pdev, ...) {
<+...
- e = kzalloc(e1, e2)
+ e = devm_kzalloc(&pdev->dev, e1, e2)
...
?-kfree(e);
...+>
}
@rem depends on prb@
identifier platform.removefn;
expression e;
@@
removefn(...) {
<...
- kfree(e);
...>
}
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Chromebooks (at least Acer C720 and Pixel) implement an ACPI object
for TPM, but don't implement the _DSM method to support PPI. As
a result, the TPM driver fails to load on those machines after
commit 1569a4c4ce (ACPI / TPM: detect PPI features by checking
availability of _DSM functions) which causes them to fail to
resume from system suspend, becuase they require the TPM hardware
to be put into the right state during resume and the TPM driver
is necessary for that.
Fix the problem by making tpm_add_ppi() return 0 when tpm_ppi_handle
is still NULL after walking the ACPI namespace in search for the PPI
_DSM, which allows the TPM driver to load and operate the hardware
(during system resume in particular), but avoid creating the PPI
sysfs group in that case.
This change is based on a prototype patch from Jiang Liu.
Fixes: 1569a4c4ce (ACPI / TPM: detect PPI features by checking availability of _DSM functions)
References: https://bugzilla.kernel.org/show_bug.cgi?id=74021
Reported-by: James Duley <jagduley@gmail.com>
Reported-by: Phillip Dixon <phil@dixon.gen.nz>
Tested-by: Brandon Casey <drafnel@gmail.com>
Cc: 3.14+ <stable@vger.kernel.org> # 3.14+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
On 64 bit systems the agp_info struct has a 4 byte hole between
->agp_mode and ->aper_base. We need to clear it to avoid disclosing
stack information to userspace.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This will be needed for pending changes to the scsi midlayer that now
calls lower level block APIs, as well as any blk-mq driver that wants to
contribute to the random pool.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Jens Axboe <axboe@fb.com>
Here are a number of small tty/serial driver fixes for 3.15-rc2. Also
in here are some Documentation file removals for drivers that we removed
a long time ago, no need to keep it around any longer.
All of these have been in linux-next for a bit.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlNRmhMACgkQMUfUDdst+yl1egCgi9FsrVUE57dZ2AJNuVwxeh90
cDQAoIAbaKSE1ooen/txjFI27rB92qgZ
=d+yo
-----END PGP SIGNATURE-----
Merge tag 'tty-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are a number of small tty/serial driver fixes for 3.15-rc2. Also
in here are some Documentation file removals for drivers that we
removed a long time ago, no need to keep it around any longer.
All of these have been in linux-next for a bit"
* tag 'tty-3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "serial: 8250, disable "too much work" messages"
serial: amba-pl011: fix regression, causing an Oops on rmmod
tty: Fix help text of SYNCLINK_CS
tty: fix memleak in alloc_pid
ttyprintk: Allow built as a module
ttyprintk: Fix wrong tty_unregister_driver() call in the error path
serial: 8250, disable "too much work" messages
Documentation/serial: Delete obsolete driver documentation
serial: omap: Fix missing pm_runtime_resume handling by simplifying code
serial_core: Fix pm imbalance on unbind
serial: pl011: change Rx burst size to half of trigger level
serial: timberdale: Depend on X86_32
serial: st-asc: Fix SysRq char handling
Revert "serial: clps711x: Give a chance to perform useful tasks during wait loop"
serial_core: Fix conditional start_tx on ring buffer not empty
serial: efm32: use $vendor,$device scheme for compatible string
serial: omap: free the wakeup settings in remove
Merge ipmi fixes from Corey Minyard:
"Things collected since last kernel release.
Some of these are pretty important. The first three are bug fixes.
The next two are to hopefully make everyone happy about allowing
ACPI to be on all the time and not have IPMI have an effect on the
system when not in use. The last is a little cleanup"
* emailed patches from Corey Minyard <cminyard@mvista.com>:
ipmi: boolify some things
ipmi: Turn off all activity on an idle ipmi interface
ipmi: Turn off default probing of interfaces
ipmi: Reset the KCS timeout when starting error recovery
ipmi: Fix a race restarting the timer
Char: ipmi_bt_sm, fix infinite loop
The IPMI driver would wake up periodically looking for events and
watchdog pretimeouts. If there is nothing waiting for these events,
it's really kind of pointless to be checking for them. So modify the
driver so the message handler can pass down if it needs the lower layer
to be waiting for these. Modify the system interface lower layer to
turn off all timer and thread activity if the upper layer doesn't need
anything and it is not currently handling messages. And modify the
message handler to not restart the timer if its timer is not needed.
The timers and kthread will still be enabled if:
- the SI interface is handling a message.
- a user has enabled watching for events.
- the IPMI watchdog timer is in use (since it uses pretimeouts).
- the message handler is waiting on a remote response.
- a user has registered to receive commands.
This mostly affects interfaces without interrupts. Interfaces with
interrupts already don't use CPU in the system interface when the
interface is idle.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The default probing can cause problems with some system, slow booting,
extra CPU usages, etc. Turn it off by default and give a config option
to enable it.
From: Matthew Garrett <matthew.garrett@nebula.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The OBF timer in KCS was not reset in one situation when error recovery
was started, resulting in an immediate timeout.
Reported-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With recent changes it is possible for the timer handler to detect an
idle interface and not start the timer, but the thread to start an
operation at the same time. The thread will not start the timer in that
instance, resulting in the timer not running.
Instead, move all timer operations under the lock and start the timer in
the thread if it detect non-idle and the timer is not already running.
Moving under locks allows the last timeout to be set in both the thread
and the timer. 'Timer is not running' means that the timer is not
pending and smi_timeout() is not running. So we need a flag to detect
this correctly.
Also fix a few other timeout bugs: setting the last timeout when the
interrupt has to be disabled and the timer started, and setting the last
timeout in check_start_timer_thread possibly racing with the timer
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In read_all_bytes, we do
unsigned char i;
...
bt->read_data[0] = BMC2HOST;
bt->read_count = bt->read_data[0];
...
for (i = 1; i <= bt->read_count; i++)
bt->read_data[i] = BMC2HOST;
If bt->read_data[0] == bt->read_count == 255, we loop infinitely in the
'for' loop. Make 'i' an 'int' instead of 'char' to get rid of the
overflow and finish the loop after 255 iterations every time.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-and-debugged-by: Rui Hui Dian <rhdian@novell.com>
Cc: Tomas Cech <tcech@suse.cz>
Cc: Corey Minyard <minyard@acm.org>
Cc: <openipmi-developer@lists.sourceforge.net>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enabling SYNCLINK_CS as a module builds synclink_cs, not synclinkmp.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver is well written to be used as a module, just the exit call
is missing.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ttyprintk driver calls tty_unregister_driver() wrongly in the error
path of tty_register_driver(). Also, setting ttyprintk_driver to NULL
is utterly superfluous, so let's get rid of it, too.
Reported-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver for the "Picochip picoXcell true random number generator" was
added in v2.6.39. Its Kconfig symbol has always depended on
PICOXCELL_PC3X3. But that Kconfig symbol has never been part of the
tree. This means this driver has never been buildable. Let's remove it.
It can be re-added if its dependencies are actually part of the tree.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
HW_RANDOM_ATMEL should not only default to ARCH_AT91, it should depend
on it. This driver is useless on other architectures.
Likewise, HW_RANDOM_EXYNOS should depend on ARCH_EXYNOS, as it it
useless on other architectures.
Also set the default to HW_RANDOM for the few architecture-specific
drivers which didn't have it yet, for consistency.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This makes configuration more convenient IMHO, and avoids having to
repeat the dependency on HW_RANDOM for every single driver.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Matt Mackall <mpm@selenic.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
UML_RANDOM is the only hardware random number generator option which
does not depend on HW_RANDOM. Having it in the middle of the other
options breaks the alignment in "make menuconfig". Move it at the last
position to avoid that.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Matt Mackall <mpm@selenic.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull bmc2835 crypto fix from Herbert Xu:
"This fixes a potential boot crash on bcm2835 due to the recent change
that now causes hardware RNGs to be accessed on registration"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
hwrng: bcm2835 - fix oops when rng h/w is accessed during registration
Pull vfs updates from Al Viro:
"The first vfs pile, with deep apologies for being very late in this
window.
Assorted cleanups and fixes, plus a large preparatory part of iov_iter
work. There's a lot more of that, but it'll probably go into the next
merge window - it *does* shape up nicely, removes a lot of
boilerplate, gets rid of locking inconsistencie between aio_write and
splice_write and I hope to get Kent's direct-io rewrite merged into
the same queue, but some of the stuff after this point is having
(mostly trivial) conflicts with the things already merged into
mainline and with some I want more testing.
This one passes LTP and xfstests without regressions, in addition to
usual beating. BTW, readahead02 in ltp syscalls testsuite has started
giving failures since "mm/readahead.c: fix readahead failure for
memoryless NUMA nodes and limit readahead pages" - might be a false
positive, might be a real regression..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (63 commits)
missing bits of "splice: fix racy pipe->buffers uses"
cifs: fix the race in cifs_writev()
ceph_sync_{,direct_}write: fix an oops on ceph_osdc_new_request() failure
kill generic_file_buffered_write()
ocfs2_file_aio_write(): switch to generic_perform_write()
ceph_aio_write(): switch to generic_perform_write()
xfs_file_buffered_aio_write(): switch to generic_perform_write()
export generic_perform_write(), start getting rid of generic_file_buffer_write()
generic_file_direct_write(): get rid of ppos argument
btrfs_file_aio_write(): get rid of ppos
kill the 5th argument of generic_file_buffered_write()
kill the 4th argument of __generic_file_aio_write()
lustre: don't open-code kernel_recvmsg()
ocfs2: don't open-code kernel_recvmsg()
drbd: don't open-code kernel_recvmsg()
constify blk_rq_map_user_iov() and friends
lustre: switch to kernel_sendmsg()
ocfs2: don't open-code kernel_sendmsg()
take iov_iter stuff to mm/iov_iter.c
process_vm_access: tidy up a bit
...
Commit "d9e7972 hwrng: add randomness to system from rng sources"
exposed a bug in the bcm2835-rng driver resulting in boot failure
on Raspberry Pi due to the following oops:
[ 28.261523] BUG: soft lockup - CPU#0 stuck for 23s! [swapper:1]
[ 28.271058]
[ 28.275958] CPU: 0 PID: 1 Comm: swapper Not tainted 3.14.0+ #11
[ 28.285374] task: db480000 ti: db484000 task.ti: db484000
[ 28.294279] PC is at bcm2835_rng_read+0x28/0x48
[ 28.302276] LR is at hwrng_register+0x1a8/0x238
.
.
.
The RNG h/w is not completely initialized and enabled before
hwrng_register() is called and so the bcm2835_rng_read() fails.
Fix this by making the warmup/enable writes before registering
the RNG source with the hwrng core.
Signed-off-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull x86 platform driver updates from Matthew Garrett:
"Support for the new keyboard features on the Thinkpad Carbon, a bunch
of updates for the Sony and Toshiba drivers, a new driver for upcoming
Alienware hardware and a few misc fixes. There's a couple of patches
that got Acked today but aren't invasive, so I'll send a further PR
for them next week"
* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86: (28 commits)
alienware-wmi: cover some scenarios where memory allocations would fail
Add WMI driver for controlling AlienFX features on some Alienware products
fujitsu-tablet: add support for Lifebook T901 and T902
x86, platform: Make HP_WIRELESS option text more descriptive
x86, acpi: LLVMLinux: Remove nested functions from Thinkpad ACPI
save and restore adaptive keyboard mode for suspend and,resume
support Thinkpad X1 Carbon 2nd generation's adaptive keyboard
toshiba_acpi: Fix whitespace
toshiba_acpi: Update version and copyright info
toshiba_acpi: Add accelerometer support
toshiba_acpi: Add ECO mode led support
toshiba_acpi: Add touchpad enable/disable support-
toshiba_acpi: Add keyboard backlight support
toshiba_acpi: Adapt Illumination code to use SCI
toshiba_acpi: Add System Configuration Interface
thinkpad_acpi: Fix inconsistent mute LED after resume
sonypi: Simplify dependencies
Revert "X86 platform: New BayTrail IOSF-SB MBI driver"
sony-laptop: remove useless sony-laptop versioning
sony-laptop: add smart connect control function
...
If the renamed symbol is defined lib/iomap.c implements ioport_map and
ioport_unmap and currently (nearly) all platforms define the port
accessor functions outb/inb and friend unconditionally. So
HAS_IOPORT_MAP is the better name for this.
Consequently NO_IOPORT is renamed to NO_IOPORT_MAP.
The motivation for this change is to reintroduce a symbol HAS_IOPORT
that signals if outb/int et al are available. I will address that at
least one merge window later though to keep surprises to a minimum and
catch new introductions of (HAS|NO)_IOPORT.
The changes in this commit were done using:
$ git grep -l -E '(NO|HAS)_IOPORT' | xargs perl -p -i -e 's/\b((?:CONFIG_)?(?:NO|HAS)_IOPORT)\b/$1_MAP/'
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask
us to pick up the changes to avoid conflicts. A large chunk of this
are clock drivers (bcm281xx, exynos, versatile, shmobile), aside from
that, reset controllers for STi as well as a large rework of the
Marvell Orion/EBU watchdog driver are notable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=u/FI
-----END PGP SIGNATURE-----
Merge tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Arnd Bergmann:
"These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask us
to pick up the changes to avoid conflicts.
A large chunk of this are clock drivers (bcm281xx, exynos, versatile,
shmobile), aside from that, reset controllers for STi as well as a
large rework of the Marvell Orion/EBU watchdog driver are notable"
* tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
Revert "dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac."
Revert "net: stmmac: Add SOCFPGA glue driver"
ARM: shmobile: r8a7791: Fix SCIFA3-5 clocks
ARM: STi: Add reset controller support to mach-sti Kconfig
drivers: reset: stih416: add softreset controller
drivers: reset: stih415: add softreset controller
drivers: reset: Reset controller driver for STiH416
drivers: reset: Reset controller driver for STiH415
drivers: reset: STi SoC system configuration reset controller support
dts: socfpga: Add sysmgr node so the gmac can use to reference
dts: socfpga: Add support for SD/MMC on the SOCFPGA platform
reset: Add optional resets and stubs
ARM: shmobile: r7s72100: fix bus clock calculation
Power: Reset: Generalize qnap-poweroff to work on Synology devices.
dts: socfpga: Update clock entry to support multiple parents
ARM: socfpga: Update socfpga_defconfig
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
net: stmmac: Add SOCFPGA glue driver
watchdog: orion_wdt: Use %pa to print 'phys_addr_t'
drivers: cci: Export CCI PMU revision
...
will be showing up in Intel Broadwell CPU's.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=RtMT
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull /dev/random changes from Ted Ts'o:
"A number of cleanups plus support for the RDSEED instruction, which
will be showing up in Intel Broadwell CPU's"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
random: Add arch_has_random[_seed]()
random: If we have arch_get_random_seed*(), try it before blocking
random: Use arch_get_random_seed*() at init time and once a second
x86, random: Enable the RDSEED instruction
random: use the architectural HWRNG for the SHA's IV in extract_buf()
random: clarify bits/bytes in wakeup thresholds
random: entropy_bytes is actually bits
random: simplify accounting code
random: tighten bound on random_read_wakeup_thresh
random: forget lock in lockless accounting
random: simplify accounting logic
random: fix comment on "account"
random: simplify loop in random_read
random: fix description of get_random_bytes
random: fix comment on proc_do_uuid
random: fix typos / spelling errors in comments
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 3.15:
- Added 3DES driver for OMAP4/AM43xx
- Added AVX2 acceleration for SHA
- Added hash-only AEAD algorithms in caam
- Removed tegra driver as it is not functioning and the hardware is
too slow
- Allow blkcipher walks over AEAD (needed for ARM)
- Fixed unprotected FPU/SSE access in ghash-clmulni-intel
- Fixed highmem crash in omap-sham
- Add (zero entropy) randomness when initialising hardware RNGs
- Fixed unaligned ahash comletion functions
- Added soft module depedency for crc32c for initrds that use crc32c"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (60 commits)
crypto: ghash-clmulni-intel - use C implementation for setkey()
crypto: x86/sha1 - reduce size of the AVX2 asm implementation
crypto: x86/sha1 - fix stack alignment of AVX2 variant
crypto: x86/sha1 - re-enable the AVX variant
crypto: sha - SHA1 transform x86_64 AVX2
crypto: crypto_wq - Fix late crypto work queue initialization
crypto: caam - add missing key_dma unmap
crypto: caam - add support for aead null encryption
crypto: testmgr - add aead null encryption test vectors
crypto: export NULL algorithms defines
crypto: caam - remove error propagation handling
crypto: hash - Simplify the ahash_finup implementation
crypto: hash - Pull out the functions to save/restore request
crypto: hash - Fix the pointer voodoo in unaligned ahash
crypto: caam - Fix first parameter to caam_init_rng
crypto: omap-sham - Map SG pages if they are HIGHMEM before accessing
crypto: caam - Dynamic memory allocation for caam_rng_ctx object
crypto: allow blkcipher walks over AEAD data
crypto: remove direct blkcipher_walk dependency on transform
hwrng: add randomness to system from rng sources
...
doubling of the default queue length though.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=AoMS
-----END PGP SIGNATURE-----
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio updates from Rusty Russell:
"Nothing exciting: virtio-blk users might see a bit of a boost from the
doubling of the default queue length though"
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio-blk: base queue-depth on virtqueue ringsize or module param
Revert a02bbb1ccf: MAINTAINERS: add virtio-dev ML for virtio
virtio: fail adding buffer on broken queues.
virtio-rng: don't crash if virtqueue is broken.
virtio_balloon: don't crash if virtqueue is broken.
virtio_blk: don't crash, report error if virtqueue is broken.
virtio_net: don't crash if virtqueue is broken.
virtio_balloon: don't softlockup on huge balloon changes.
virtio: Use pci_enable_msix_exact() instead of pci_enable_msix()
MAINTAINERS: virtio-dev is subscribers only
tools/virtio: add a missing )
tools/virtio: fix missing kmemleak_ignore symbol
tools/virtio: update internal copies of headers
Add predicate functions for having arch_get_random[_seed]*(). The
only current use is to avoid the loop in arch_random_refill() when
arch_get_random_seed_long() is unavailable.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
If we have arch_get_random_seed*(), try to use it for emergency refill
of the entropy pool before giving up and blocking on /dev/random. It
may or may not work in the moment, but if it does work, it will give
the user better service than blocking will.
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Use arch_get_random_seed*() in two places in the Linux random
driver (drivers/char/random.c):
1. During entropy pool initialization, use RDSEED in favor of RDRAND,
with a fallback to the latter. Entropy exhaustion is unlikely to
happen there on physical hardware as the machine is single-threaded
at that point, but could happen in a virtual machine. In that
case, the fallback to RDRAND will still provide more than adequate
entropy pool initialization.
2. Once a second, issue RDSEED and, if successful, feed it to the
entropy pool. To ensure an extra layer of security, only credit
half the entropy just in case.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
To help assuage the fears of those who think the NSA can introduce a
massive hack into the instruction decode and out of order execution
engine in the CPU without hundreds of Intel engineers knowing about
it (only one of which woud need to have the conscience and courage of
Edward Snowden to spill the beans to the public), use the HWRNG to
initialize the SHA starting value, instead of xor'ing it in
afterwards.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
These are a recurring cause of confusion, so rename them to
hopefully be clearer.
Signed-off-by: Greg Price <price@mit.edu>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The variable 'entropy_bytes' is set from an expression that actually
counts bits. Fortunately it's also only compared to values that also
count bits. Rename it accordingly.
Signed-off-by: Greg Price <price@mit.edu>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
With this we handle "reserved" in just one place. As a bonus the
code becomes less nested, and the "wakeup_write" flag variable
becomes unnecessary. The variable "flags" was already unused.
This code behaves identically to the previous version except in
two pathological cases that don't occur. If the argument "nbytes"
is already less than "min", then we didn't previously enforce
"min". If r->limit is false while "reserved" is nonzero, then we
previously applied "reserved" in checking whether we had enough
bits, even though we don't apply it to actually limit how many we
take. The callers of account() never exercise either of these cases.
Before the previous commit, it was possible for "nbytes" to be less
than "min" if userspace chose a pathological configuration, but no
longer.
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Greg Price <price@mit.edu>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
We use this value in a few places other than its literal meaning,
in particular in _xfer_secondary_pool() as a minimum number of
bits to pull from the input pool at a time into either output
pool. It doesn't make sense to pull more bits than the whole size
of an output pool.
We could and possibly should separate the quantities "how much
should the input pool have to have to wake up /dev/random readers"
and "how much should we transfer from the input to an output pool
at a time", but nobody is likely to be sad they can't set the first
quantity to more than 1024 bits, so for now just limit them both.
Signed-off-by: Greg Price <price@mit.edu>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The only mutable data accessed here is ->entropy_count, but since
10b3a32d2 ("random: fix accounting race condition") we use cmpxchg to
protect our accesses to ->entropy_count here. Drop the use of the
lock.
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Price <price@mit.edu>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This logic is exactly equivalent to the old logic, but it should
be easier to see what it's doing.
The equivalence depends on one fact from outside this function:
when 'r->limit' is false, 'reserved' is zero. (Well, two facts;
the other is that 'reserved' is never negative.)
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Greg Price <price@mit.edu>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This comment didn't quite keep up as extract_entropy() was split into
four functions. Put each bit by the function it describes.
Signed-off-by: Greg Price <price@mit.edu>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The loop condition never changes until just before a break, so we
might as well write it as a constant. Also since a996996dd7
("random: drop weird m_time/a_time manipulation") we don't do anything
after the loop finishes, so the 'break's might as well return
directly. Some other simplifications.
There should be no change in behavior introduced by this commit.
Signed-off-by: Greg Price <price@mit.edu>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
After this remark was written, commit d2e7c96af added a use of
arch_get_random_long() inside the get_random_bytes codepath.
The main point stands, but it needs to be reworded.
Signed-off-by: Greg Price <price@mit.edu>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
There's only one function here now, as uuid_strategy is long gone.
Also make the bit about "If accesses via ..." clearer.
Signed-off-by: Greg Price <price@mit.edu>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
A bad implementation of virtio might cause us to mark the virtqueue
broken: we'll dev_err() in that case, and the device is useless, but
let's not BUG().
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
When bringing a new RNG source online, it seems like it would make sense
to use some of its bytes to make the system entropy pool more random,
as done with all sorts of other devices that contain per-device or
per-boot differences.
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use devm_*() functions to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use devm_*() functions to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use devm_clk_get() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use devm_clk_get() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use devm_clk_get() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use devm_ioremap_resource() in order to make the code simpler,
and remove redundant return value check of platform_get_resource()
because the value is checked by devm_ioremap_resource().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use devm_ioremap_resource() in order to make the code simpler,
and remove redundant return value check of platform_get_resource()
because the value is checked by devm_ioremap_resource().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Merge "qcom driver changes for v3.15" from Kumar Gala:
We've split Qualcomm MSM support into legacy and multiplatform. These
drivers are only relevant on the multiplatform supported SoCs so switch the
Kconfig depends to ARCH_QCOM.
* tag 'qcom-drivers-for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
gpio: msm: switch Kconfig to ARCH_QCOM depends
hwrng: msm: switch Kconfig to ARCH_QCOM depends
power: reset: msm - switch Kconfig to ARCH_QCOM depends
drm/msm: drop ARCH_MSM Kconfig depend
tty: serial: msm: Enable building msm_serial for ARCH_QCOM
We've split Qualcomm MSM support into legacy and multiplatform. The RNG
driver is only relevant on the multiplatform supported SoCs so switch the
Kconfig depends to ARCH_QCOM.
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
CC: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
The loff_t type may be wider than phys_addr_t (e.g. on 32-bit systems).
Consequently, the file offset may be truncated in the assignment.
Currently, /dev/mem wraps around, which may cause applications to read
or write incorrect regions of memory by accident.
Let's follow POSIX file semantics here and return 0 when reading from
and -EFBIG when writing to an offset that cannot be represented by a
phys_addr_t.
Note that the conditional is optimized out by the compiler if loff_t
has the same size as phys_addr_t.
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some small char/misc driver fixes, along with some
documentation updates, for 3.14-rc3. Nothing major, just a number of
fixes for reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlL+hvIACgkQMUfUDdst+ykGRQCgpi/LgypVecwQlv73TsHLNZo/
ybIAniXJlLgf4xu3q0J+8br3iQ7sg8pC
=m+up
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fixes from Greg KH:
"Here are some small char/misc driver fixes, along with some
documentation updates, for 3.14-rc3. Nothing major, just a number of
fixes for reported issues"
* tag 'char-misc-3.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Revert "misc: eeprom: sunxi: Add new compatibles"
Revert "ARM: sunxi: dt: Convert to the new SID compatibles"
misc: mic: fix possible signed underflow (undefined behavior) in userspace API
ARM: sunxi: dt: Convert to the new SID compatibles
misc: eeprom: sunxi: Add new compatibles
misc: genwqe: Fix potential memory leak when pinning memory
Documentation:Update Documentation/zh_CN/arm64/memory.txt
Documentation:Update Documentation/zh_CN/arm64/booting.txt
Documentation:Chinese translation of Documentation/arm64/tagged-pointers.txt
raw: set range for MAX_RAW_DEVS
raw: test against runtime value of max_raw_minors
Drivers: hv: vmbus: Don't timeout during the initial connection with host
Drivers: hv: vmbus: Specify the target CPU that should receive notification
VME: Correct read/write alignment algorithm
mei: don't unset read cb ptr on reset
mei: clear write cb from waiting list on reset
