Ioana Ciornei says:
====================
dpaa2-eth: add QBMAN statistics
This patch set adds ethtool statistics for pending frames/bytes
in Rx/Tx conf FQs and number of buffers in pool.
The first patch adds support for the query APIs in the DPIO driver
while the latter actually exposes the statistics through ethtool.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add statistics for pending frames in Rx/Tx conf FQs and
number of buffers in pool. Available through ethtool -S.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add FQ (Frame Queue) and BP (Buffer Pool) query APIs that
users of QBMan can invoke to see the status of the queues
and pools that they are using.
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2018-12-19
Here's the main bluetooth-next pull request for 4.21:
- Multiple fixes & improvements for Broadcom-based controllers
- New USB ID for an Intel controller
- Support for new Broadcom controller variants
- Use DEFINE_SHOW_ATTRIBUTE to simplify debugfs code
- Eliminate confusing "last event is not cmd complete" warning message
- Added vendor suspend/resume support for H:5 (3-Wire UART) controllers
- Various other smaller improvements & fixes
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* virt_wifi - wireless control simulation on top of
another network interface
* hwsim configurability to test capabilities similar
to real hardware
* various mesh improvements
* various radiotap vendor data fixes in mac80211
* finally the nl_set_extack_cookie_u64() we talked
about previously, used for
* peer measurement APIs, right now only with FTM
(flight time measurement) for location
* made nl80211 radio/interface announcements more complete
* various new HE (802.11ax) things:
updates, TWT support, ...
-----BEGIN PGP SIGNATURE-----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=EpyK
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2018-12-19' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This time we have too many changes to list, highlights:
* virt_wifi - wireless control simulation on top of
another network interface
* hwsim configurability to test capabilities similar
to real hardware
* various mesh improvements
* various radiotap vendor data fixes in mac80211
* finally the nl_set_extack_cookie_u64() we talked
about previously, used for
* peer measurement APIs, right now only with FTM
(flight time measurement) for location
* made nl80211 radio/interface announcements more complete
* various new HE (802.11ax) things:
updates, TWT support, ...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In case a command which completes in Command Status was sent using the
hci_cmd_send-family of APIs there would be a misleading error in the
hci_get_cmd_complete function, since the code would be trying to fetch
the Command Complete parameters when there are none.
Avoid the misleading error and silently bail out from the function in
case the received event is a command status.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Broadcom controller on aries S5PV210 boards sends out a couple of
unknown packets after the firmware is loaded. This will cause
logging of errors such as:
Bluetooth: hci0: Frame reassembly failed (-84)
This is probably also the case with other boards, as there are related
Android userspace patches for custom ROMs such as
https://review.lineageos.org/#/c/LineageOS/android_system_bt/+/142721/
Since this appears to be intended behaviour, treated them as diagnostic
packets.
Note that this is another variant of commit 01d5e44ace
("Bluetooth: hci_bcm: Handle empty packet after firmware loading")
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The radiotap vendor data might be placed after some other
radiotap elements, and thus when accessing it, need to access
the correct offset in the skb data. Fix the code accordingly.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix two bugs in ieee80211_get_vht_max_nss():
* the spec says we should round down
(reported by Nissim)
* there's a double condition, the first one is wrong,
supp_width == 0 / ext_nss_bw == 2 is valid in 80+80
(found by smatch)
Fixes: b0aa75f0b1 ("ieee80211: add new VHT capability fields/parsing")
Reported-by: Nissim Bendanan <nissimx.bendanan@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Due to the alignment handling, it actually matters where in the code
we add the 4 bytes for the presence bitmap to the length; the first
field is the timestamp with 8 byte alignment so we need to add the
space for the extra vendor namespace presence bitmap *before* we do
any alignment for the fields.
Move the presence bitmap length accounting to the right place to fix
the alignment for the data properly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After phy_start() phylib takes care of all needed actions, including
aneg settings and checking link state. There's no need to set state
PHY_CHANGELINK in drivers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Microsemi has been bought by Microchip and Microchip is supporting those
switches.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NAME_DISTRIBUTOR messages are transmitted through unicast link on TIPC
2.0, by contrast, the messages are delivered through broadcast link on
TIPC 1.7. But at present, NAME_DISTRIBUTOR messages received by
broadcast link cannot be handled in tipc_rcv() until an unicast message
arrives, which may lead to a significant delay to update name table.
To avoid this delay, we will also deal with broadcast NAME_DISTRIBUTOR
message on broadcast receive path.
Signed-off-by: Zhenbo Gao <zhenbo.gao@windriver.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
3c1bcc8614 ("net: ethernet: Convert phydev advertize and supported
from u32 to link mode") left some unused code in phy_probe(), remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz says:
This series is essentially a cleanup to align with the rest of the NIC
switchdev drivers and make us
more robust and clear/n: currently the PF netdev serves as the mlx5
e-switch uplink netdev
representor when going into switchdev mode and back as plain NIC
netdev when going out.
This causes some irregularities and misc troubles.
Move to use dedicated uplink rep, as we have for the VF vports.
The uplink rep netdev does has sysfs link and supports the sriov vf
mac ndo, these two are in
use by libvirt and other orchestrators, It also has richer ethtool
support to allow controlling the
port link & mtu along with supporting dcb and plugging into the mlx5
lag logic.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJcF/MBAAoJEEg/ir3gV/o+apkIAKVeB/ha8qiY+9ntA9B8HVxO
cYb+fv4+DuYjTg/nN5QdYSAisN4SwFDA5ukz/ckr6XwV65EgTjAtlon/fHg/rDyz
YT3dJRP9yjNXKxRvxa0K4PmTasmXGXzaJzsXYemHsfCDdnkNknZsqA+yoNe+2c40
HoNsdy/Pvr18PjzYtpX0BiuSjH623daBmdFH0o+rwuwsApkAUlBJfosTg/7xyU7v
TAjy8S1HCloJ7OAjOlzXVmYr65sAlQoFr860vLDQ7Og7JemxjSXQ+AdNb6mSAvZ5
LBEvCA3G5tb4OkFX+1i/alxOcuG8/FoO+O3ZQWve1DNxoS76po851bgHXIdZCPg=
=pqTq
-----END PGP SIGNATURE-----
Merge tag 'mlx5-uplink-rep-2018-12-15' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed:
====================
mlx5-uplink-rep-2018-12-15
Or Gerlitz says:
This series is essentially a cleanup to align with the rest of the NIC
switchdev drivers and make us
more robust and clear/n: currently the PF netdev serves as the mlx5
e-switch uplink netdev
representor when going into switchdev mode and back as plain NIC
netdev when going out.
This causes some irregularities and misc troubles.
Move to use dedicated uplink rep, as we have for the VF vports.
The uplink rep netdev does has sysfs link and supports the sriov vf
mac ndo, these two are in
use by libvirt and other orchestrators, It also has richer ethtool
support to allow controlling the
port link & mtu along with supporting dcb and plugging into the mlx5
lag logic.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
function br_multicast_toggle now always return 0,
so the variable 'err' is unneeded.
Also cleanup dead branch in br_changelink.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c:1070:5: warning:
variable 'op' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c:1342:5: warning:
variable 'cmd_op' set but not used [-Wunused-but-set-variable]
'op' never used since introduction in commit 7cb03b2347 ("qlcnic:
Support VF-PF communication channel commands.")
'cmd_op' not used since commit 6226204bcf ("qlcnic: Fix operation
type and command type.")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On many devices the RTL8723BS device gets reset during suspend/resume,
causing it to lose its firmware and all state.
Testing has shown it drops back to communicating at 115200 bps and sends
sync-request packages, indicating it has been fully reset.
This commit fixes this by queueing a reprobe on resume.
This mirrors how USB RTL BT devices, which have the same problem, are
handled in the btusb driver, there we set the USB_QUIRK_RESET_RESUME for
all RTL devices, which also causes a reprobe on resume. The only difference
is that here we need to do the reprobe ourselves.
Since we are doing a full reprobe on resume now, we can also turn off the
device on suspend to save power while suspended.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add support for vendor specific suspend / resume callbacks.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Trivial fix to clean up an indentation issue, remove spaces
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Trivial fix to clean up an indentation issue
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
HCI_QUIRK_RESET_ON_CLOSE quirk is required for BT v1.0 based devices,
to send a reset command to the chip during hci device close. Serdev
architecture is used for the latest BT chips, which doesn't require to
send the reset command during close. If still chips required reset
command during close, it would be better enabling it in the vendor
probes or in proto setup.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The barriers are redundant because atomic_test_and_clear_bit() already
provides the required full ordering for the cases in question (that is,
when the bit is cleared).
Signed-off-by: Andrea Parri <andrea.parri@amarulasolutions.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The BCM43430A0 has the default MAC address 43:43:A0:12:1F:AC if none
is given. This address was found when enabling Bluetooth on a bunch of
boards with the AMPAK AP6210 module, all sharing the same address. It
also contains the sequence 4343A0, which is suspicious as that is also
the name the chip identifies itself as.
Add this to the list of default MAC addresses and leave it to the user
to configure a valid one.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The BCM4330 chip is a 802.11 a/b/g/n + Bluetooth 4.0 + HS controller.
This patch adds a compatible string match to the serdev driver for the
Bluetooth part of the chip.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The BCM20702A1 chip is a single-chip Bluetooth 4.0 controller and
transceiver. It is found in the AMPAK AP6210 WiFi+BT package.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The datasheets for BCM20702 and BCM43438 both have power up time
sequence graphs, however they are slightly different. Both chips
also have an internal power-on-reset, which holds the chip in reset
for a short time after the regulators are enabled.
For the BCM20702, the time period from when the regulators are enabled,
until the chip settles and comes out of sleep state, is 6564 ~ 8171 us.
For the BCM43438, the graph only shows the time period from when the
regulators are enabled until the chip responds by driving the host's
CTS line low, assuming the host has already driven its RTS line low.
This is shown to be 6.5 sleep cycles, with the sleep clock at 32.768
kHz. This is around 2 ms.
Wait a full 10 ms after the regulators are enabled to account for signal
rising times.
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Broadcom Bluetooth chips have two power inputs, VBAT and VDDIO.
The former provides overall power for the chip, while the latter powers
the I/O pins and buffers.
Model these two as regulator supplies, and let the driver manage them
in the same way as it does the clock supply.
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Broadcom Bluetooth controllers support a secondary LPO clock at
32.768 kHz. This external clock provides low power timing, and also
a way to detect the frequency of the main reference clock. On many
designs without NVRAM and a non-default reference clock, this must
be used or the controller will not function correctly.
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Originally the device tree binding only specified one clock reference,
with the name "extclk". The driver simply retrieves the clock without
bothering to specify a name.
Since we added a second clock to the binding, we need to fetch the
clocks by name now. First we try the new name "txco", then fall back
to the old name "extclk", and finally try retrieving a clock without
using any name, to cover any instances where a bad device tree or
firmware worked by accident.
In the last case, we should take care that we don't get the same
clock twice when we add support for the "lpo" clock.
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The driver currently checks the clk pointer for an error condition, as
returned by clk_get, before every invocation of the clk consumer API.
This is redundant if the goal is simply to ignore the errors, thereby
making the clk optional. The clk consumer API already checks if the
pointer is NULL or not.
Simplify the code a bit by assigning NULL to the clk pointer if the
error condition is one we want to ignore, which is every error except
deferred probing.
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
On some systems that actually have the bluetooth controller wired up
with an extra clock signal, it's possible the bluetooth controller
probes before the clock provider. clk_get would return a defer probe
error, which was not handled by this driver.
Handle this properly, so that these systems can work reliably.
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The BCM4330 is a 802.11 a/b/g/n WiFi + Bluetooth 4.0 chip from Broadcom.
It is found in the Ampak AP6330 WiFi+BT module. The partiular one I have
identifies as BCM4330B1 for Bluetooth and BCM4330/4 for WiFi.
It is unclear if the AP6330 module uses this revision of the BCM4330, or
if there are multiple revisions. The module does not have revision
markings. This patch elects to use just BCM4330 for the compatible
string.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The BCM20702A1 is a Bluetooth 4.0 chip from Broadcom. It is found in the
Ampak AP6210 WiFi+BT module, identified from the read verbose config info
command response. However the Bluetooth firmware provided by vendors uses
the name BCM20710. This patch elects to use the chip ID returned by the
chip for the compatible string.
Reviewed-by: Rob Herring <robh@kernel.org>
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Broadcom Bluetooth chips have two power inputs, VBAT and VDDIO.
The former provides overall power for the chip, while the latter powers
the I/O pins and buffers.
This patch adds properties for the two so we can describe the power
supply relationships.
Reviewed-by: Rob Herring <robh@kernel.org>
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Broadcom Bluetooth controllers can take up to two external clocks:
an external frequency reference, substituting the main crystal, and a
LPO clock at 32.768 kHz substituting the internal LPO clock.
In particular, the external LPO clock must be used when the controller
does not have NVRAM connected, and the main reference frequency is not
the default 20 MHz. This is described in detail in the datasheet.
The original "extclk" clock name is ambiguous as to which of these it
refers to, and some designs might even require both.
This patch deprecates the existing name, and adds "txco" and "lpo".
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This is one of only two files that initialize a semaphore to a negative
value. We don't really need the two semaphores here at all, but can do
the same thing in more conventional and more effient way, by using a
single waitqueue and an atomic thread counter.
This gets us a little bit closer to eliminating classic semaphores from
the kernel. It also fixes a corner case where we fail to continue after
one of the threads fails to start up.
An alternative would be to use a split kthread_create()+wake_up_process()
and completely eliminate the separate synchronization.
Acked-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far phy_error() silently stops the PHY state machine. If the network
driver doesn't inform about a MDIO error then the user may wonder why
his network is down. Let's print the stack trace to facilitate search
for the root cause of the error.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers phy_is_started() and __phy_is_started() to avoid open-coded
checks whether PHY has been started. To make the check easier move
PHY_HALTED before PHY_UP in enum phy_state. Further improvements:
phy_start_aneg():
Return -EBUSY and print warning if function is called from a non-started
state (DOWN, READY, HALTED). Better check because function is exported
and drivers may use it incorrectly.
phy_interrupt():
Return IRQ_NONE also if state is DOWN or READY. We should never receive
an interrupt in one of these states, but better play safe.
phy_stop():
Just return and print a warning if PHY is in a non-started state.
This warning should help to identify drivers with unbalanced calls to
phy_start() / phy_stop().
phy_state_machine():
Schedule state machine run only if PHY is in a started state.
E.g. if state is READY we don't need the state machine, it will be
started by phy_start().
v2:
- don't use __func__ within phy_warn_state
v3:
- use WARN() instead of printing error message to facilitate debugging
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a workaround to restart the phylib state machine in case of a
MDIO access timeout. Seems it was introduced to deal with the
consequences of a too small MDIO timeout. See also commit message of
c3b084c24c ("net: fec: Adjust ENET MDIO timeouts") which increased
the timeout value later. Due to the later timeout value fix it seems
to be safe to remove the workaround.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two statements that are indented too much by one space each,
fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Peng Li says:
====================
net: hns3: code optimizations & bugfixes for HNS3 driver
This patchset includes bugfixes and code optimizations for the HNS3
ethernet controller driver
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When caculating the SSU buffer, it first allocate tx and
rx private buffer, then the remaining buffer is for rx
shared buffer. The remaining buffer size should be at
least bigger than or equal to the shared_std, which is the
minimum shared buffer size required by the driver, but
currently if the remaining buffer size is equal to the
shared_std, it returns failure, which causes SSU buffer
allocation failure problem.
This patch fixes this problem by rounding up shared_std before
checking the the remaining buffer size bigger than or equal to
the shared_std.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware expects the buffer size set to SSU is aligned to
256 bytes, this patch aligns the buffer size to 256 byte using
roundup or rounddown function.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support of getting tx and dv buffer size through
firmware, because different version of hardware requires different
size of tx and dv buffer.
This patch also add dv_buf_size to tc' private buffer size even if
pfc is not enable for the tc.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
