This shouldn't change anything since the core calls the events folder
"events" anyways.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The ad7991/ad7995/ad7999 does not have a configuration register like the
other devices that can be written and read. The configuration is written as
part of the conversion sequence.
Fixes: 0f7ddcc1bf ("iio:adc:ad799x: Write default config on probe and reset alert status on probe")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Allows explicity enabling of events
Previously, events were always reported as enabled, but actually only
implicitly enabled when updating the buffer scan mode
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
only report an event as enabled if it actually is enabled
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
rename since function is used by all chips with ALERT pin, not just ad7997/8
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
writing ALERT_EN and BUSY_ALERT to the chip config register clears
pending alerts, BUSY_ALERT is cleared when reading back the register
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
an IRQ is necessary to handle the ALERT condition; without
IRQ, the IIO event interface serves no purpose
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
last two bits of ADC and limit values are zero and should not be reported
(ad7993, ad7997); compare with read_raw()
event values are 10 (ad7993, ad7997) or 12 bit max., check the range on write
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Stable@vger.kernel.org
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
My static checker is upset that we check IS_ERR(t->reg) when we know it
is not an ERR_PTR.
Checking for IS_ERR() twice is often a sign of confusion and buggy code.
In this case, if the call to "ret = regulator_enable(st->vref);" fails,
then we call "regulator_disable(st->vref);" and that's a mistake because
"st->vref" is not enabled.
I fixed these problems and Hartmut Knaack pointed out a couple unneeded
IS_ERR() checks in ad799x_remove() so I have removed those as well.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Correct spelling typo in comment within staging/iio
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver is now at a reasonable quality level. Move it out of staging.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
