Use hda_bus instead of hdac_bus in the SKL ASoC platform driver to enable
reuse of legacy HDA codec drivers.
Signed-off-by: Rakesh Ughreja <rakesh.a.ughreja@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for HDA BE DAIs in SKL platform driver.
Signed-off-by: Rakesh Ughreja <rakesh.a.ughreja@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When no I2S based codec entries are found in the BIOS, check if there are
any HDA codecs detected on the bus. Based on the number of codecs found
take appropriate action in machine driver. If there are two HDA codecs
i.e. iDisp + HDA found on the bus, register DAIs and DAI links for both.
If only one codec i.e. iDisp is found then load only iDisp machine driver.
Signed-off-by: Rakesh Ughreja <rakesh.a.ughreja@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add machine driver for Intel platforms (SKL/KBL/BXT/APL) with
HDA and iDisp codecs. This patch adds support for only iDisp (HDMI/DP)
codec. In the following patches support for HDA codecs will be added.
This should work for other Intel platforms as well e.g. GLK,CNL
however this series is not tested on all the platforms.
Signed-off-by: Rakesh Ughreja <rakesh.a.ughreja@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Expose a table containing machine driver information for HDAudio-based
platforms handled by ASoC on Intel hardware.
We only set constant values that are valid across multiple
platforms. The firmware name used by the DSP will be set dynamically
for each platform.
The table is made of a single entry for now, if we need more
complicated set-up where HDAudio is mixed with ACPI-enumerated devices
(I2C, SoundWire) then we'd expect the differentiation to be handled
through information provided by the BIOS (as done for KBL
Chromebooks).
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
HID made of either Wolfson/CirrusLogic PCI ID + 8804 identifier.
This helps enumerate the HifiBerry Digi+ HAT boards on the Up2 platform.
The scripts at https://github.com/thesofproject/acpi-scripts can be
used to add the ACPI initrd overlays.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
New calibration sequence allows rt5682 do calibration without
MCLK.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The step of DAC/ADC volume scale changes from 0.375dB to 0.75dB
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Restrict the formats possible on the TDM interface depending on the width
of the TDM slot and let dpcm merging do the rest.
Fixes: d60e4f1e4b ("ASoC: meson: add tdm interface driver")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return value of request_irq() was irgnored. Fix this and report
the failure if any
Fixes: 6dc4fa179f ("ASoC: meson: add axg fifo base driver")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add audio clock controller and ARB reset controller module
implication for the device using them
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the CPU DAI does not initialise rate_max, say if using
using KNOT or CONTINUOUS, then the rate_max field will be
initialised to 0. A value of zero in the rate_max field of
the hardware runtime will cause the sound card to support no
sample rates at all. Obviously this is not desired, just a
different mechanism is being used to apply the constraints. As
such update the setting of rate_max in dpcm_init_runtime_hw
to be consistent with the non-DPCM cases and set rate_max to
UINT_MAX if nothing is defined on the CPU DAI.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
devm_pinctrl_get will only return NULL in the case that pinctrl
is not built into the kernel and all the pinctrl functions used
by the DAPM core are appropriately stubbed for that case. There
is no need to error out of snd_soc_dapm_new_control_unlocked
if pinctrl isn't built into the kernel, so change the
IS_ERR_OR_NULL to just an IS_ERR.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The clock code now has stub functions defined in its header files so
the ifdefs around clocking code should no longer be necessary.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Also add these typos to spelling.txt so checkpatch.pl will look for them.
Link: http://lkml.kernel.org/r/88af06b9de34d870cb0afc46cfd24e0458be2575.1529471371.git.fthain@telegraphics.com.au
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This round brings couple of framework changes, a new driver and usual driver
updates:
- New managed helper for dmaengine framework registration
- Split dmaengine pause capability to pause and resume and allow drivers to
report that individually
- Update dma_request_chan_by_mask() to handle deferred probing
- Move imx-sdma to use virt-dma
- New driver for Actions Semi Owl family S900 controller
- Minor updates to intel, renesas, mv_xor, pl330 etc
-----BEGIN PGP SIGNATURE-----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=kbCC
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.19-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull DMAengine updates from Vinod Koul:
"This round brings couple of framework changes, a new driver and usual
driver updates:
- new managed helper for dmaengine framework registration
- split dmaengine pause capability to pause and resume and allow
drivers to report that individually
- update dma_request_chan_by_mask() to handle deferred probing
- move imx-sdma to use virt-dma
- new driver for Actions Semi Owl family S900 controller
- minor updates to intel, renesas, mv_xor, pl330 etc"
* tag 'dmaengine-4.19-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (46 commits)
dmaengine: Add Actions Semi Owl family S900 DMA driver
dt-bindings: dmaengine: Add binding for Actions Semi Owl SoCs
dmaengine: sh: rcar-dmac: Should not stop the DMAC by rcar_dmac_sync_tcr()
dmaengine: mic_x100_dma: use the new helper to simplify the code
dmaengine: add a new helper dmaenginem_async_device_register
dmaengine: imx-sdma: add memcpy interface
dmaengine: imx-sdma: add SDMA_BD_MAX_CNT to replace '0xffff'
dmaengine: dma_request_chan_by_mask() to handle deferred probing
dmaengine: pl330: fix irq race with terminate_all
dmaengine: Revert "dmaengine: mv_xor_v2: enable COMPILE_TEST"
dmaengine: mv_xor_v2: use {lower,upper}_32_bits to configure HW descriptor address
dmaengine: mv_xor_v2: enable COMPILE_TEST
dmaengine: mv_xor_v2: move unmap to before callback
dmaengine: mv_xor_v2: convert callback to helper function
dmaengine: mv_xor_v2: kill the tasklets upon exit
dmaengine: mv_xor_v2: explicitly freeup irq
dmaengine: sh: rcar-dmac: Add dma_pause operation
dmaengine: sh: rcar-dmac: add a new function to clear CHCR.DE with barrier
dmaengine: idma64: Support dmaengine_terminate_sync()
dmaengine: hsu: Support dmaengine_terminate_sync()
...
After our evaluation, we need to modify the default values to make sure
the volume applied immediately.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit a655de808c ("ASoC: core: Allow topology to override
machine driver FE DAI link config.") caused soc_dai_hw_params to
be come dependent on the substream private_data being set with
a pointer to the snd_soc_pcm_runtime. Currently, CODEC to CODEC
links don't set this, which causes a NULL pointer dereference:
[<4069de54>] (soc_dai_hw_params) from
[<40694b68>] (snd_soc_dai_link_event+0x1a0/0x380)
Since the ASoC core in general assumes that the substream
private_data will be set to a pointer to the snd_soc_pcm_runtime,
update the CODEC to CODEC links to respect this.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cold reboot stress test found that the hda irq could access rirb ring
buffer before its memory gets allocated which resulting in null
pointer dereference inside snd_hdac_bus_update_rirb().
Fix it by moving the skl_acquire_irq after ring buffer allocation.
While here, also change err return from -EBUSY to actual error code.
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit 143b44845d ("ASoC: wm9712: replace codec to component")
"wm9712-codec" got renamed to "wm9712-component", however, this change
never got propagated down to the actual board/platform drivers. E.g. on
Colibri T20 this lead to the following spew upon boot with sound/touch
being broken:
[ 2.214121] tegra-snd-wm9712 sound: ASoC: CODEC DAI wm9712-hifi not registered
[ 2.222137] tegra-snd-wm9712 sound: snd_soc_register_card failed (-517)
...
[ 2.344384] tegra-snd-wm9712 sound: ASoC: CODEC DAI wm9712-hifi not registered
[ 2.351885] tegra-snd-wm9712 sound: snd_soc_register_card failed (-517)
...
[ 2.668339] tegra-snd-wm9712 sound: ASoC: CODEC DAI wm9712-hifi not registered
[ 2.675811] tegra-snd-wm9712 sound: snd_soc_register_card failed (-517)
...
[ 3.208408] tegra-snd-wm9712 sound: ASoC: CODEC DAI wm9712-hifi not registered
[ 3.216312] tegra-snd-wm9712 sound: snd_soc_register_card failed (-517)
...
[ 3.235397] tegra-snd-wm9712 sound: ASoC: CODEC DAI wm9712-hifi not registered
[ 3.248938] tegra-snd-wm9712 sound: snd_soc_register_card failed (-517)
...
[ 14.970443] ALSA device list:
[ 14.996628] No soundcards found.
This commit finally fixes this again.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Add quirks to select the right input-map, jack-detect pin, etc. for:
Linx Linx7 tablet
Onda V975w tablet
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A fairly big update, including quite a bit of core activity this time
around (which is good to see) along with a fairly large set of new
drivers.
- A new snd_pcm_stop_xrun() helper which is now used in several
drivers.
- Support for providing name prefixes to generic component nodes.
- Quite a few fixes for DPCM as it gains a bit wider use and more
robust testing.
- Generalization of the DIO2125 support to a simple amplifier driver.
- Accessory detection support for the audio graph card.
- DT support for PXA AC'97 devices.
- Quirks for a number of new x86 systems.
- Support for AM Logic Meson, Everest ES7154, Intel systems with
RT5682, Qualcomm QDSP6 and WCD9335, Realtek RT5682 and TI TAS5707.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAltxVZsTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0CtwB/0U+IUWLlojWD6RDfueycvc9TiZW0t4
gBT3OD8f4oif0MuMy6oE2ag8JPNU8n5MnO14U366GDaEyZPj79W7f50Q8Nnyht/n
py6fQfyo7Ec2hFJstDI42KvDymTbAer6hnAUJarr/FdZHdGeOfYV+s7aHp5aEQAS
KACnX8qWo87VePouNBorqWXWueAJTb6zpWy7YQ1KGb/pJIAeue2Y9pLRGXQos1BS
E1AP+ge2BMnz7BeiCgw/39hN6X545nJ1fcZKuIu8Gqy9ahqEDHgmBWPAehtGnfVj
D8JPplTaBFtAsJwi18b7ApWtcytpizPPN/l3NTA4fTRJQe9kxfDmnE7b
=fvKX
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v4.19
A fairly big update, including quite a bit of core activity this time
around (which is good to see) along with a fairly large set of new
drivers.
- A new snd_pcm_stop_xrun() helper which is now used in several
drivers.
- Support for providing name prefixes to generic component nodes.
- Quite a few fixes for DPCM as it gains a bit wider use and more
robust testing.
- Generalization of the DIO2125 support to a simple amplifier driver.
- Accessory detection support for the audio graph card.
- DT support for PXA AC'97 devices.
- Quirks for a number of new x86 systems.
- Support for AM Logic Meson, Everest ES7154, Intel systems with
RT5682, Qualcomm QDSP6 and WCD9335, Realtek RT5682 and TI TAS5707.
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1056531 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
On some platforms it has been noted that a pop noise can be
witnessed when capturing audio, mainly for first time after a
headset jack has been inserted. This is due to a DC offset in the
Mic PGA and so to avoid this delays are required when powering
up the capture path.
This commit rectifies the problem by adding delays post Mic PGA and
post Mixin PGA. The post Mic PGA delay is determined based on
Mic Bias voltage, and is only applied the first time after a
headset jack is inserted.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of harcoding that a core must always be called "DSPn"
add a name member to struct wm_adsp so that the owning codec
driver can provide a custom name. This allows for re-use of
the wm_adsp driver with parts where the processing cores are
named differently.
If no name is provided the default DSPn name is used.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To allow for more flexibility in naming of DSP-type cores
move the creation of the firmware controls to the codec
drivers instead of having a hardcoded list in wm_adsp.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The offset of the DSP core needs to be taken into account for the DSP
preloader control get and put. Currently the dsp->preloaded variable
will only ever be read/updated on the first DSP, whilst this doesn't
affect the operation of the control the readback will be incorrect.
Signed-off-by: Ajit Pandey <ajit.pandey@cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The driver expects to find the device id in rt5677_of_match.data, however
it is currently assigned to rt5677_of_match.type. Fix this.
The problem was found with the help of clang:
sound/soc/codecs/rt5677.c:5010:36: warning: expression which evaluates to
zero treated as a null pointer constant of type 'const void *'
[-Wnon-literal-null-conversion]
{ .compatible = "realtek,rt5677", RT5677 },
^~~~~~
Fixes: ddc9e69b9d ("ASoC: rt5677: Hide platform data in the module sources")
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For some reason order of startup/hw_params/prepare are reversed
in dynamic compress usecase when compared to dpcm usecase. This is
a issue with platforms like QCOM where it expects the BE to be
initialized before FE.
Interestingly the compress trigger callback order is inline with dpcm.
Am not 100% sure why the compress audio case has been reversed.
This patch is making the order inline with dpcm.
If the reverse ordering is just co-incendental then this change
makes sense and will avoid inventing some new mechanism to cope
with ordering.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
ACP->SYSMEM DMA happens at every I2S->SYSMEM period
completion. Thus, there is delay of x frames till
I2S->SYSMEM reaches a period length. This delay is
communicated to user space.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Give position on ACP->SYSMEM DMA channel for
the number of bytes that have been transferred on
the basis of current descriptor under service.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In capture case we don't want ACP to SYSMEM dma
to be circular. This is because if an in place DSP
filter is applied to captured output then circular DMA
can overwrite the filter value with stale data.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add missing break statement in order to prevent the code from falling
through to the default case.
Addresses-Coverity-ID: 115050 ("Missing break in switch")
Reported-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This patch removes unused header files from common.h.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch removes unused header files from the driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch removes unused header files from the driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch converts common helper functions in to proper module
and also fixes below warning.
WARNING: sound/soc/qcom/snd-soc-sdm845: 'qcom_snd_parse_of' exported twice.
Previous export was in sound/soc/qcom/snd-soc-apq8096.ko
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1381093 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1468847 ("Missing break in switch")
Addresses-Coverity-ID: 1468849 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1222121 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 146568 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1369526 ("Missing break in switch")
Addresses-Coverity-ID: 1369529 ("Missing break in switch")
Addresses-Coverity-ID: 1451415 ("Missing break in switch")
Addresses-Coverity-ID: 115103 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1364478 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In case memory resources for *card* were allocated, release them before
return.
Addresses-Coverity-ID: 1472244 ("Resource leak")
Fixes: 6b1687bf76 ("ASoC: qcom: add sdm845 sound card support")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DRM based audio components get registered inside the component framework
bind callback. However component framework has a big mutex lock taken for
every call to component_add, component_del and bind, unbind callbacks.
This can lead to deadlock situation if we are trying to add new/remove
component within a bind/unbind callbacks. Which is what was happening
with bcm2837 rpi 3.
Revert this change till we sort out the mutex issue.
Reported-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove auto rebinding support, as component framework can deadlock
in few usecases if we are trying to add new/remove component within
a bind/unbind callbacks.
Card rebinding is ASoC core feature so all the previous component
framework stuff in q6dsp remains removed.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove auto rebinding support, as component framework can deadlock
in few usecases if we are trying to add new/remove component within
a bind/unbind callbacks.
Card rebinding is ASoC core feature so all the previous component
framework stuff in q6dsp remains removed.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add DEPENDS_ON QCOM_APR for SND_SOC_SDM845 to fix the
warning: unmet direct dependencies detected for
SND_SOC_QDSP6.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Rohit kumar <rohitkr@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 115050 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1357430 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 115045 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 115043 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 146354 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 115042 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 115041 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 115047 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1271174 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1056547 ("Missing break in switch")
Addresses-Coverity-ID: 1056548 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1271173 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Take into account the base delay set in pointer callback.
There are cases where a pointer function populates
runtime->delay, such as:
./sound/pci/hda/hda_controller.c
./sound/soc/intel/atom/sst-mfld-platform-pcm.c
This delay was getting lost and was overwritten by delays
from codec or cpu dai delay function if exposed.
Now,
Total delay = base delay + cpu_dai delay + codec_dai delay
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit e57d4ca882 (ASoC: wcd9335: add support to wcd9335
codec) due to build failures caused by missing dependencies.
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit c8cb5f775c (ASoC: vert "ASoC: wcd9335: add
CLASS-H Controller support) due to missing dependencies.
Signed-off-by: Mark Brown <broonie@kernel.org>
Pointer 'priv' is assigned and not used, removing this allows
the removal of pointer 'rtd'.
Cleans up clang warning:
warning: variable 'priv' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Variable osrate is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'osrate' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds support to parse cpu, platform and codec
device nodes and add them in dai-links. Also, update
apq8096 machine driver to use the common API.
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Rohit kumar <rohitkr@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
CLASS-H controller/Amplifier is common accorss Qualcomm WCD codec series.
This patchset adds basic CLASS-H controller apis for WCD codecs after
wcd9335 to use.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Qualcomm WCD9335 Codec is a standalone Hi-Fi audio codec IC,
It supports both I2S/I2C and SLIMbus audio interfaces.
On slimbus interface it supports two data lanes; 16 Tx ports
and 8 Rx ports. It has Seven DACs and nine dedicated interpolators,
Seven (six audio ADCs, and one VBAT ADC), Multibutton headset
control (MBHC), Active noise cancellation and Sidetone paths
and processing.
This patchset adds very basic support for playback and capture
via the 9 interpolators and ADC respectively.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch changes some functions that are not used by other objects
to static.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds multichannel PCM output support for LD11/LD20.
Currently driver tested and supported only 2ch, 6ch, and 8ch.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a potential execution path in which function
platform_get_resource() returns NULL. If this happens,
we will end up having a NULL pointer dereference.
Fix this by replacing devm_ioremap with devm_ioremap_resource,
which has the NULL check and the memory region request.
This code was detected with the help of Coccinelle.
Cc: stable@vger.kernel.org
Fixes: 2bd8d1d5cf ("ASoC: sirf: Add audio usp interface driver")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
tegra_alc5632_probe() increments reference count of device nodes
with of_parse_phandle(), but there is no code decrementing them
in the driver.
The patch adds of_node_put() to tegra_alc5632_remove() and
to error handling paths in the probe.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As original license mentioned, it is GPL-2.0 in SPDX.
Then, MODULE_LICENSE() should be "GPL v2" instead of "GPL".
See ${LINUX}/include/linux/module.h
"GPL" [GNU Public License v2 or later]
"GPL v2" [GNU Public License v2]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As original license mentioned, it is GPL-2.0 in SPDX.
Then, MODULE_LICENSE() should be "GPL v2" instead of "GPL".
See ${LINUX}/include/linux/module.h
"GPL" [GNU Public License v2 or later]
"GPL v2" [GNU Public License v2]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove duplicated entry and add missing zero in rate constraints.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix typo in macro TEGRA30_I2S_SLOT_CTRL_TOTAL_SLOTS_MASK.
Signed-off-by: Edward Cragg <edward.cragg@codethink.co.uk>
Signed-off-by: Jorge Sanjuan <jorge.sanjuan@codethink.co.uk>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The conversion from PCM format type to bits needs an explicit cast,
and it'll be uglier. Since we have a standard macro for that, let's
use it instead.
This patch fixes the sparse warning:
sound/soc/soc-generic-dmaengine-pcm.c:200:63: warning: restricted snd_pcm_format_t degrades to integer
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PCM format type is with __bitwise, so we should use the dedicated
snd_pcm_format_t instead of int.
This fixes the sparse warning like:
sound/soc/codecs/pcm186x.c:268:44: warning: incorrect type in initializer (different base types)
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the new helper function snd_mask_set_format() for avoiding the
ugly cast with __force prefix.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
As sparse warns, the PCM format type can't be dealt as integer as
found in Intel SST driver codes.
Fix them in the following two ways:
- The open code with snd_mask_set() and params->masks reference is
replaced with params_set_format()
- The rest codes with snd_mask_set(fmt, SNDRV_PCM_FORMAT_XXX) are
replaced with the new helper, snd_mask_set_format().
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
fmt in snd_soc_dai_link_event() contains the format bit position, not
the format bit itself. Hence it can be a simple integer instead of
the explicit u64.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
It seems that __user prefix was forgotten to be added to
dmaengine_copy_user callback while we refactored the user-copy PCM
core.
This patch adds the missing prefix, remove the superfluous cast, and
add the needed cast (__force is needed for downgrading from user
pointer to kernel pointer), too.
Spotted by a sparse warning like:
sound/soc/soc-generic-dmaengine-pcm.c:397:27: warning: incorrect type in initializer (incompatible argument 4 (different address spaces))
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
zx-tdm driver sets the DAI driver definitions with the format bits
wrongly set with SNDRV_PCM_FORMAT_*, instead of SNDRV_PCM_FMTBIT_*.
This patch corrects the definitions.
Spotted by a sparse warning:
sound/soc/zte/zx-tdm.c:363:35: warning: restricted snd_pcm_format_t degrades to integer
Fixes: 870e0ddc43 ("ASoC: zx-tdm: add zte's tdm controller driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Drop amlogic prefix in front of the generic DT properties and change
property "name" to "model".
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use IRQ_RETVAL instead of the open coded ternary operation.
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes
sound/soc/amd/acp-da7219-max98357a.c: In function 'cz_probe':
sound/soc/amd/acp-da7219-max98357a.c:367:3: warning: 'ret' may
be used uninitialized in this function [-Wmaybe-uninitialized]
dev_err(&pdev->dev, "Failed to register regulator: %d\n",
ret);
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DA7219 for our platform need to be configured for 1.8V.
Hence, we add a volatge regulator with supplies
of 1.8V in the machine driver.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
include DAPM Mux and output widgets into the list.
Signed-off-by: Rakesh Ughreja <rakesh.a.ughreja@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This looks like a copy/paste issue, but clearly there is an inversion
that is obvious when checking the arguments.
Detected with Sparse - now that we have fewer warnings this one was
easy to find.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify code and add relevant casts to make Sparse warnings go away
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sst_dma_new and sst_dma_free are not used in any other file and don't
have a prototype. Move to static functions and remove
EXPORT_SYMBOL_GPL statement.
Reported by sparse warnings.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make sure definitions are consistent with usage.
Detected with Sparse.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make all Sparse warnings go away by using le16/32_to_cpu.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On Qualcomm platforms, specifically with SLIMbus interfaced codecs,
the codec slim channel numbers are passed to DSP while configuring
the slim audio path. Having get_channel_map() would allow dais to
share such information across multiple dais.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch fixes the issue of the delay volume applied.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When CONFIG_SND_PCM_IEC958 is disabled, we get a link error for the
new driver:
sound/soc/meson/axg-spdifout.o: In function `axg_spdifout_hw_params':
axg-spdifout.c:(.text+0x650): undefined reference to `snd_pcm_create_iec958_consumer_hw_params'
The other users use 'select', so we should do the same here.
Fixes: 53eb4b7aaa ("ASoC: meson: add axg spdif output")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SSP DAI now handles the clocking setup itself, all it needs is the
master clock frequency. Remove the code from Zylonite and Magician
platforms.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the axg sound card to handle the specifities of the axg audio
sub system.
This card is required to:
* setup the dpcm links specific to the AXG (with a cpu sound dai)
* handle the 4 lanes masks of the tdm interfaces
* add the loopback link when a tdm pad interface has a playback
stream
* handle multi-codec links
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Amlogic's axg card driver can't use snd_soc_of_parse_tdm_slot()
directly because it needs to handle 4 mask for each direction.
Yet the parsing of each mask is the same, so export
snd_soc_of_get_slot_mask() to reuse the the existing code.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add Amlogic's axg TDM input driver which take the TDM signal of 4 input
lanes and push the decoded audio samples to TODDR fifo
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add Amlogic's axg tdm output driver which pulls data from FRDDR fifo
and produce the TDM signals for 4 output lanes.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add Amlogic's axg TDM interface driver. This driver manages the format
and clocks provided on the pads.
On this SoC, each stream direction provides 4 serial lanes. This makes
a maximum of 8 channels in i2s modes and 128 channels in DSP modes.
While each lanes operate on the same slot number (same bit clock), they
may have different TDM masks. This requires to provide a function to let
the card set the 4 masks, in lieu of the usual set_tdm_slots() callback
of the dai driver.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add Amlogic's axg TDM core driver. On this SoC, tdm is bit more
complex than usual, mainly because the different TDM input decoders can
be attached to any of TDM pad interface, including the output pads.
For the this, TDM on this SoC is modeled like this:
- TDM interface provides the DAIs the codecs will be attached to.
The main responsibility of this driver is to manage the pad format
and the TDM clock rates.
- TDM Formatters: These are the entities which are actually dealing with
the TDM signal. TDMOUT produce a TDM signal from the audio sample
provided by FRDDR using the clocks provided the TDM interface. TDMIN
feeds TODDR with audio sample using the clocks and TDM signal provided
by the TDM Interface.
- TDM Streams: This provides the link between 1 DAI stream of the TDM
interface and one (or more) TDM formatters.
This driver provides the TDM formatter and TDM stream operations.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
While the two error labels "err" and "err_clk_put" goto the same place
it is rather confusing that the earlier one is certainly used later
again.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull the generic drm_audio_component support, which will be used later
for AMD/ATI and other HD-audio HDMI codec drivers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a quirk for the "Connect Tablet 9" tablet, this tablet has a
mono-speaker. Otherwise it works fine with the defaults.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add quirk table entries for the following tablets:
ITWorks TW701
Ployer Momo7w
Trekstor win7
Yours 8"
These all use the default settings, except that they only have a single
speaker and thus need the mono-speaker quirk.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
During my initial round of bytcr_rt5651 long-name patches I did not include
a difference for mono vs stereo speaker setups in the longname because it
seems that all 5651 devices with only a single speaker do some mixing of
left + right on the PCB.
However further testing has shown that while this works great when only
playing audio on the left or right channel, the output becomes garbled
when using both channels at once. Something which does not happen when
using the Stereo DAC MIXL / MIXR switches to mix the channels together
inside the codec and then only outputting on a single channel.
So we need to have separate UCM profiles and thus separate long-names
for devices with a mono speaker vs stereo speakers. Just as we already
have for the bytcr_rt5640 case.
This commit adds a new BYT_RT5651_MONO_SPEAKER quirk and adds "stereo-spk"
or "mono-spk" to the long-name based on this and enables this mapping on
devices with a mono speaker.
Changing the long-name like this is ok for now, since I'm still working
on the UCM profiles, so they are not in upstream alsa-lib yet.
This brings the long-name naming scheme fully in sync with the bytcr_rt5640
case, which is good from a consistency pov.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
During the recent cleanup series 3 of the 6 input mappings where removed
from the bytcr_rt5651 machine driver because testing showed that none of
them were used.
However some devices do actually have their internal mic on IN2 (and
only IN2, not IN1 and IN2), this did not show during previous tests
due to a bug in the userspace UCM input device switching code.
This commit re-adds the IN2 mapping for devices with the internal mic.
on IN2 and the headser mic on IN3 and enables this mapping on devices
with their internal mic on IN2.
This commit also changes the default internal mic input to IN2, because
all my 7 test devices have their mic there.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With the default over current detect limit of 1500uA headsets on often
get detected as headphones on the VIOS LTH17 and even when detected as
headset the OVCD current triggers often while plugged in, resulting in
false-positive button press detection.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some boards have I2cSerialBusV2, GpioIo, GpioInt as ACPI resources, other
boards may have I2cSerialBusV2, GpioInt, GpioIo instead. We want the
GpioIo one for the ext-amp-enable-gpio.
So far we've been assuming that the GpioIo one always comes first, this
commit adds code to detect which one comes first and to add the right
gpio-mapping.
This fixes sound not working on the Vios LTH17 laptop.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a mixer control for the IN3 Boost volume, IN3 is used for the headset
mic on most devices, so this is necessary to control the headset mic
volume.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the compressed streams in DSP firmwares are
identified essentially by looking at a fixed location inside
the firmware. This is fragile and also limits things to a
single compressed stream.
Here a new form of firmware parameter is added, the HOST_BUFFER
which identifies a compressed stream from meta-data in the
firmware file. This is more robust and allows for the possiblity
of using multiple streams per core in the future. Currently the
implementation is still limited to a single stream and will
use the first HOST_BUFFER parameter encountered. If there aren't
any HOST_BUFFER parameters it will fall back to the legacy way
of finding the host buffer.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Newer voice control firmwares can capture multiple audio channels.
Allow up to 8 channels for future-proofing.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently when creating ALSA control names for the DSP the length of any
prefix applied to the CODEC is not taken into account. Whilst this is
mostly harmless it does result in ALSA doing the truncation of the
control names and printing a warning. It is better to have the driver do
the truncation so it can truncate from the start of parameter name
itself to give a greater chance of the result maintain a unique name.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 6396bb2215 ("treewide: kzalloc() -> kcalloc()") was
overlooked when doing some refactoring to the algorithm list
handling, which lead to twice as much buffer being allocated
as required for reading the algorithm list. A kcalloc is no
longer appropriate since the allocation size is now in bytes
not registers, as such change back to kzalloc.
Fixes: 7f7cca08ab ("ASoC: wm_adsp: Simplify handling of alg offset and length")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All controls derived from the loaded firmware should be created prior
to returning from the preloader's put function, such that they are
immediately available to user-space.
Signed-off-by: Stuart Henderson <stuarth@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the spdif output serializer of the axg SoC family
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the capture memory interface of Amlogic's axg SoCs.
TDM, SPDIF or PDM input devices place audio samples inside this FIFO.
The FIFO content is then pushed to DDR
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the playback memory interface of Amlogic's axg SoCs.
This device pulls data from DDR to an internal FIFO.
This FIFO is then used to feed TDM and SPDIF Output devices.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Amlogic's axg SoCs have two types of fifos which are the memory
interfaces of the audio subsystem. FRDDR provides the playback
interface while TODDR provides the capture interface.
The way these fifos operate is very similar. Only a few settings
are specific to each.
They implement the same pcm driver here and the specifics of each
will be dealt with the related DAI driver.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add documentation for power management of HDAC HDMI codec device for
various scenarios such as S0/S3, probe and playback use case.
Signed-off-by: Sriram Periyasamy <sriramx.periyasamy@intel.com>
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that the component framework is integrated into the ASoC core,
remove any redundant code in this driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that the component framework is integrated into the ASoC core,
remove any redundant code in this driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that the component framework is integrated into the ASoC core,
remove any redundant code in this driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that the component framework is integrated into the ASoC core,
remove any redundant code in this driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch aims at achieving dynamic behaviour of audio card when
the dependent components disappear and reappear.
With this patch the card is removed if any of the dependent component
is removed and card is added back if the dependent component comes back.
All this is done using component framework and matching based on
component name.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_pcm_lib_mmap_vmalloc() was supposed to be implemented with
somewhat special for vmalloc handling, but in the end, this turned to
just the default handler, i.e. NULL. As the situation has never
changed over decades, let's rip it off.
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is the final step for more generic support of DRM audio
component. The generic audio component code is now moved to its own
file, and the symbols are renamed from snd_hac_i915_* to
snd_hdac_acomp_*, respectively. The generic code is enabled via the
new kconfig, CONFIG_SND_HDA_COMPONENT, while CONFIG_SND_HDA_I915 is
kept as the super-class.
Along with the split, three new callbacks are added to audio_ops:
pin2port is for providing the conversion between the pin number and
the widget id, and master_bind/master_unbin are called at binding /
unbinding the master component, respectively. All these are optional,
but used in i915 implementation and also other later implementations.
A note about the new snd_hdac_acomp_init() function: there is a slight
difference between this and the old snd_hdac_i915_init(). The latter
(still) synchronizes with the master component binding, i.e. it
assures that the relevant DRM component gets bound when it returns, or
gives a negative error. Meanwhile the new function doesn't
synchronize but just leaves as is. It's the responsibility by the
caller's side to synchronize, or the caller may accept the
asynchronous binding on the fly.
v1->v2: Fix missing NULL check in master_bind/unbind
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HD-audio i915 binding code contains a single pointer, hdac_acomp,
for allowing the access to audio component from the master bind/unbind
callbacks. This was needed because the callbacks pass only the device
pointer and we can't guarantee the object type assigned to the drvdata
(which is free for each controller driver implementation).
And this implementation will be a problem if we support multiple
components for different DRM drivers, not only i915.
As a solution, allocate the audio component object via devres and
associate it with the given device, so that the component callbacks
can refer to it via devres_find().
The removal of the object is still done half-manually via
devres_destroy() to make the code consistent (although it may work
without the explicit call).
Also, the snd_hda_i915_register_notifier() had the reference to
hdac_acomp as well. In this patch, the corresponding code is removed
by passing hdac_bus object to the function, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For allowing other drivers to use the DRM audio component, rename the
i915_audio_component_* with drm_audio_component_*, and split the
generic part into drm_audio_component.h. The i915 specific stuff
remains in struct i915_audio_component, which contains
drm_audio_component as the base.
The license of drm_audio_component.h is kept to MIT as same as the the
original i915_component.h.
This is a preliminary change for further development, and no
functional changes by this patch itself, merely code-split and
renames.
v1->v2: Use SPDX for drm_audio_component.h, fix remaining i915
argument in drm_audio_component.h
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Having interrupts enabled for ACP<->SYSMEM DMA transfer, we are in
for an interrupt storm.
For both playback and capture interrupts should be enabled for
I2S<->ACP DMA.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Earlier, ch1 was used to define ACP-SYSMEM transfer and ch2 for
ACP-I2S transfer. With recent patches ch1 is used to define channel
order number 1 and ch2 as channel order number 2. Thus,
Playback:
ch1:SYSMEM->ACP
ch2:ACP->I2S
Capture:
ch1:I2S->ACP
ch1:ACP->SYSMEM
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 943fa02282 ("ASoC: hdmi-codec: Use different name for playback
streams") broke hdmi-codec's routing between it's output "TX" widget
and the S/PDIF or I2S streams by renaming the streams.
Whether an error occurs or not is dependent on whether there is another
widget called "Playback" registered by some other component - if there
is, that widget will be (incorrectly) bound to the HDMI codec's "TX"
output widget. If we end up connecting "TX" incorrectly, it can result
in components not being started, causing no audio output.
Since the I2S and S/PDIF streams now have different names, we can't
use a static route at component level to describe the relationship, so
arrange to dynamically create the route when the DAI driver is probed.
Fixes: 943fa02282 ("ASoC: hdmi-codec: Use different name for playback streams")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The data->port_data[] array has AFE_MAX_PORTS elements so the check
should be >= instead of > or we write one element beyond the end of the
array.
Fixes: e3a33673e8 ("ASoC: qdsp6: q6routing: Add q6routing driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The main thing is that the data->priv[] array has AFE_PORT_MAX elements
so the > condition should be >=. But we may as well check for negative
values as well just to be safe.
Fixes: 24c4cbcfac ("ASoC: qdsp6: q6afe: Add q6afe dai driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the component does not match the configuration table provided
by the card, let soc-core check the component node for a name prefix
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As done for format and channels, add the possibility to merge
the backend rates on the frontend rates.
This useful if the backend does not support all rates supported by the
frontend, or if several backends (cpu and codecs) with different
capabilities are connected to the same frontend.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The goal of this patch is to simplify a bit dpcm runtime stream merge
by removing several local variables.
ATM, merge functions return the BE 'filter' values which should then be
filtered against the FE stream values. This create a lot of local
variable and unnecessary init of min and max.
Instead of this, we can pass the FE stream values directly and let the
BE filtering functions perform the merge 'in-place'
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Enable reporting of button presses now that the codec driver recently has
gotten support for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Disable jack-detection and thus the codec IRQ over suspend/resume.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Enable button press detection for headsets by using the ovcd IRQ to get
notified of button presses.
This is modelled after (almost exactly copied from) the button press code
for the rt5640 which has identical ovcd hardware.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow the machine driver to disable jack-detect over a suspend/resume by
calling snd_soc_component_set_jack(NULL).
Note this renames rt5651_set_jack, where all the jack-enable work was done
to rt5651_enable_jack_detect. This function can now no longer fail as it
does not request the IRQ anymore. It can still be passed an invalid jack
source, but that should never happen, so this is now logged and treated as
no jack source.
Cc: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On removal we must free the IRQ *before* cancelling the jack-detect work,
so that the jack-detect work cannot be rescheduled by the IRQ.
Before this commit we were cancelling the jack-detect work from the
driver remove callback, while relying on devm to free the IRQ, which
happens after the remove callback.
This is the wrong order. This commit uses a devm-action to register
a devm callback which cancels the work, before requesting the IRQ
(devm tears things down in reverse order). This also allows us to
remove the now empty remove driver callback.
Cc: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The rt5651 does not have a built-in speaker amplifier, so it is often
used together with an external amplifier. On Cherry Trail boards this
external amplifier's enable pin is driven through a GPIO, which is
given as the first GPIO in the ACPI resources of the codec fwnode.
This commit adds support to the bytcr_rt5651 for this GPIO, fixing
the speaker not working on CHT devices with a rt5651 codec.
Cc: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the getting of the codec_dev, to add device-props to it, out of
byt_rt5651_add_codec_device_props() and into its caller,
snd_byt_rt5651_mc_probe().
This is a preparation patch for adding support for an external amplifier
enable GPIO, which requires further accesses to the codec_dev.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove is_valleyview helper, this is not necessary, we can simply call
x86_match_cpu() directly instead.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a quirk for the Lenovo Miix2 8 tablet, this tablet uses a digital
mic on DMIC1 and has a mono-speaker. The jack-detect uses the default
settings..
Reported-and-tested-by: russianneuromancer@ya.ru
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
'cmd_pause' DMA channel capability means that respective DMA engine
supports both pausing and resuming given DMA channel. However, in some
cases it is important to know if DMA channel can be paused without the
need to resume it. This is a typical requirement for proper residue
reading on transfer timeout in UART drivers. There are also some DMA
engines with limited hardware, which doesn't really support resuming.
Reporting pause and resume capabilities separately allows UART drivers to
properly check for the really required capabilities and operate in DMA
mode also in systems with limited DMA hardware. On the other hand drivers,
which rely on full channel suspend/resume support, should now check for
both 'pause' and 'resume' features.
Existing clients of dma_get_slave_caps() have been checked and the only
driver which rely on proper channel resuming is soc-generic-dmaengine-pcm
driver, which has been updated to check the newly added capability.
Existing 'cmd_pause' now only indicates that DMA engine support pausing
given DMA channel.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The playback DAI is connected to the DSP and the DSP might be sourcing
signals from the playback stream. Add a DAPM route between the two to make
sure that the playback DAI is powered up, when the DSP is active.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For the moment, we can't enable CONFIG_SND_PXA_SOC_SSP unless we are
building for ARM PXA or MMP:
WARNING: unmet direct dependencies detected for PXA_SSP
Depends on [n]: PLAT_PXA [=n]
Selected by [y]:
- SND_PXA_SOC_SSP [=y] && SOUND [=y] && !UML && SND [=y] && SND_SOC [=y]
This adds an explicit dependency for it.
Fixes: 0a94cf3457 ("ASoC: pxa: make SND_PXA2XX_SOC_I2S selectable")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The format specifier "%p" can leak kernel addresses.
Use "%pK" instead.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add suffix ULL to constant 256 in order to give the compiler complete
information about the proper arithmetic to use.
Notice that such constant is used in a context that expects an
expression of type u64 (64 bits, unsigned) and the following
expression is currently being evaluated using 32-bit arithmetic:
256 * fs * 2 * mclk_src_scaling[i].param
Addresses-Coverity-ID: 1432039 ("Unintentional integer overflow")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow setting a clock called 'extclk' in the device of the ssp-dai
device. If specified, this clock will be set to the mclk rate from the
DAI's .set_sysclk() callback. The DAI will also configure itself to
use that external clock.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
To comply with the style of all kernel messages, add newline
to the end of every message.
Fixes: 70fb10529f ("ASoC: rsnd: add MIX (Mixer) support")
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add suffix ULL to constant 64 in order to give the compiler complete
information about the proper arithmetic to use.
Notice that such constant is used in a context that expects an
expression of type u64 (64 bits, unsigned) and the following
expression is currently being evaluated using 32-bit arithmetic:
rate[index] * txclk_df * 64
Addresses-Coverity-ID: 1222129 ("Unintentional integer overflow")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
num_channels for slim dais are aready set int set_channel_map,
do not overwrite them in hw_params.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch add routings mixer controls for slim rx ports.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support to SLIMbus TX dais in AFE module.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Existing code already has support for SLIMbus TX and RX, only thing
that was missing from TX side was mapping between virtual to actual
DSP port ids.
This patch adds those mappings.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The XRUN trigger from the driver should be done via
snd_pcm_stop_xrun(). It simplifies the locking as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The XRUN trigger from the driver should be done via
snd_pcm_stop_xrun(). It fixes the missing stream locking as a gratis,
too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The XRUN trigger from the driver should be done via
snd_pcm_stop_xrun(). It fixes the missing stream locking as a gratis,
too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace open-codes with the standard snd_pcm_stop_xrun() helper.
It simplifies codes a lot.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add suffix ULL to constant 256 in order to give the compiler complete
information about the proper arithmetic to use.
Notice that such constant is used in a context that expects an
expression of type u64 (64 bits, unsigned) and the following
expression is currently being evaluated using 32-bit arithmetic:
256 * fs * 2 * mclk_src_scaling[i].param
Addresses-Coverity-ID: 1339616 ("Unintentional integer overflow")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
asm ports are open as part of prepare, so for use cases like
"aplay sample.wav" were sample.wav is not present. This would
call port close eventhough port was never opened. DSP would
return errors for such use cases.
Avoid doing this by checking the port state.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
afe ports are open as part of prepare, so for use cases like
"aplay sample.wav" were sample.wav is not present. This would
call port close eventhough port was never opened. DSP would
return errors for such use cases.
Avoid doing this by checking the port state.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Machine drivers statically define a number of DAI links that currently
cannot be changed or removed by topology. This means PCMs and platform
components cannot be changed by topology at runtime AND machine drivers
are tightly coupled to topology.
This patch allows topology to override the machine driver DAI link config
in order to reuse machine drivers with different topologies and platform
components. The patch supports :-
1) create new FE PCMs with a topology defined PCM ID.
2) destroy existing static FE PCMs
3) change the platform component driver.
4) assign any new HW params fixups.
5) assign a new card name prefix to differentiate this topology to userspace.
The patch requires no changes to the machine drivers, but does add some
platform component flags that the platform component driver can assign
before loading topologies.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The generated clock (gclk) driver is able to set aclk as its parent and
change its rate alone, if needed. This means that our driver no longer
needs to configure aclk and we can let gclk select and configure its
clock source.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the es7154 which is basically an es7134 with an
embedded power amplifier and lower maximum sample rate
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Drop AVDD in favor of PVDD to match the names used in the datasheet
and only claim PVDD on the es7154. The es7134 and es7144 don't have
a separate supply for the digital I/O.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that the I2S channel names are fixed, and DMA data flow order is
consistent (ch1 then ch2), we can simplify channel start order:
start the upstream channel and then the downstream channel for both
playback and capture cases.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The pointer() callback gets its value by reading the I2S BYTE_COUNT
register. This is a 64-bit runnning transaction counter. If a
transaction was aborted in the middle of a sample buffer, the counter will
stop counting on a number divisible by the buffer size. Since we actually
use it as a pointer into an aligned buffer, however, we do want to ensure
that it always starts at a number divisible by the buffer size when
starting a transaction, hence we reset it whenever starting a transaction.
To accomplish this, it wasn't necessary to zero bytescount at the
termination of each transaction, so remove this unnecessary code.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
On capture, audio data is first copied from I2S to ACP memory, and then
from ACP to SYSRAM. The I2S_TO_ACP_DMA interrupt fires on every sample
transferred from I2S to ACP memory. That is it fires ~48000 times per
second when capturing @ 48 kHz. Since we don't do anything on this
interrupt anyway, disable it to save quite a few unnecessary interrupts.
The real "work" (calling snd_pcm_period_elapsed()) is done when transfer
from ACP to SYSRAM is complete.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
On capture, audio data is first copied from I2S to ACP memory, and then
to SYSRAM. For each step the channel number increases, so the names in
the driver were wrong.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is always correct to subtract out the starting bytescount value. Even
in the case of 2^64 byte rollover (292 Million Years in the future
@ 48000 Hz) the math still works out.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 6b116dfb46 ("ASoC: AMD: make channel 1 dma as circular") made
both channels circular, so this comment and logic no longer applies. Always
stop ch2 (the channel closest to the output) before ch1. This ensures
that the downstream circular DMA channel does not continue to play/capture
repeated samples after the upstream circular DMA channel has already
stopped.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the everest es7241 which is a simple 2 channels
analog to digital converter.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We are currently using power saving mode for button detection.
However, it will impact the headset recording performance.
This patch will switch button detection to normal mode in capture
and switch to power saving mode in the end of capture.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the VDD and AVDD power supplies to the DAPM graph as some board may
need to enable a regulator to turn them on.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For each supported sample rate, the es7134 can work with several
mclk / sample rate ratio. Check if ratio we get is actually OK.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
64Khz is actually not supported by the es7134 according to the datasheet
Fixes: 9000b59d7a ("ASoC: es7134: add es7134 DAC driver")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The .set_pll() and .set_clkdiv() callbacks are considered legacy and should
not be used anymore. In order to support PXA boards on DT platforms, remove
them and let the code figure out the correct dividers and PLL base
frequencies itself.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit d767d3ce5c ("ASoC: pxa: provide PCM ops for ssp, i2s and ac97
components") created a build-time dependency to SND_PXA2XX_LIB but
missed to reflect that in Kconfig.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
use list_head for sub_dais,
since original sub_dais array is sparsely occupied
Signed-off-by: KaiChieh Chuang <kaichieh.chuang@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This platform is no longer needed on DT boards, so let's remove them to
avoid confusion. DT bindings should use the CPU DAIs (I2S/SSP/AC97)
directly.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that the functions are now available through pxa2xx-lib, hook them up
to pxa-sspi, pxa-ac97 and pxa-i2s. This allows DT platforms to use the DAIs
without a platform driver.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
To get rid of some intermediate platform layers, move pxa2xx_soc_pcm_new()
and pxa2xx_pcm_ops in pxa2xx-lib.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Clean up the namespace a bit and drop the __ prefix of all functions
exported by pxa2xx-lib. This improves the readability of the code.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that the PXA SSP bits are ported over to generic DMA, the pxa2xx-pcm
code only has a single user left. This patch folds the remaining bits into
its only user and removes the unnecessary glue layer along with its header
file.
The include dependency to linux/dma/pxa-dma.h is also gone now.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
As the pxa architecture switched towards the dmaengine slave map, the
old compatibility mechanism to acquire the dma requestor line number and
priority are not needed anymore.
This patch simplifies the dma resource acquisition, using the more
generic function dma_request_slave_channel().
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When merging codec formats, dpcm_runtime_base_format() should skip
the codecs which are not supporting the current stream direction.
At the moment, if a BE link has more than one codec, and only one
of these codecs has no capture DAI, it becomes impossible to start
a capture stream because the merged format would be 0.
Skipping invalid codec DAI solves the problem.
Fixes: b073ed4e21 ("ASoC: soc-pcm: DPCM cares BE format")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Extend dpcm_merge_chan to also check backend cpu dai channels
capabilities. Apply the same policy as soc_pcm_init_runtime_hw() for
multicodec links and only check cpu dai in this case.
Cc: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The > should be >= or we could read one element beyond the end of the
port_maps[] array.
Fixes: 7fa2d70f97 ("ASoC: qdsp6: q6afe: Add q6afe driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
As it is, dpcm_runtime_update() performs the old path and new path
update of a frontend before going on to the next frontend DAI.
Depending the order of the FEs within the rtd list, the result of
the update might be different.
For example:
* Frontend A connected to backend C, with a 48kHz playback
* Frontend B connected to backend D, with a 44.1kHz playback
* FE A appears before FE B in the rtd list of the card.
If we reparent BE C to FE B (disconnecting BE D):
* old path update of FE A will run first, and BE C will get hw_free()
and shutdown()
* new path update of FE B will run after and BE C, which is stopped,
so it will be configured at 44.1kHz, as expected
If we reparent BE D to FE A (disconnecting BE C):
* new path update of FE A will run first but since BE D is still running
at 44.1kHz, it won't be reconfigured (no call to startup() or
hw_params())
* old path update of FE B runs after, nothing happens
* In this case, we end up with a BE playing at 44.1kHz a stream which is
supposed to be played at 48Khz (too slow)
To improve this situation, this patch performs all the FE old paths update
before going on to update the new paths. With this, the result should
no longer depend on the order of the FE within the card rtd list.
Please note that there might be a small performance penalty since
dpcm_process_paths() is called twice per stream direction.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add extended ops in the hdac_bus to allow calling the ASoC HDAC library
ops to reuse the legacy HDA codec drivers with ASoC framework.
Extended ops are used by the legacy codec drivers to call into
hdac_hda library, in the subsequent patches..
Signed-off-by: Rakesh Ughreja <rakesh.a.ughreja@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove memory allocation within snd_hdac_ext_bus_device_init, to make
its behaviour identical to snd_hdac_bus_device_init. So that caller
can allocate the parent data structure containing hdac_device.
This API change helps in reusing the legacy HDA codec drivers with
ASoC platform drivers.
Signed-off-by: Rakesh Ughreja <rakesh.a.ughreja@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch removes the hdac_ext_driver structure. The legacy and
enhanced HDaudio capabilities can be handled in a backward-compatible
way without separate definitions.
Signed-off-by: Rakesh Ughreja <rakesh.a.ughreja@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch removes the hdac_ext_bus structure. The legacy and
enhanced HDaudio capabilities can be handled in a backward-compatible
way without separate definitions.
Follow-up patches in this series handle the driver definition.
Signed-off-by: Rakesh Ughreja <rakesh.a.ughreja@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
