Pull networking fixes from David Miller:
1) Two read past end of buffer fixes in AF_KEY, from Eric Biggers.
2) Memory leak in key_notify_policy(), from Steffen Klassert.
3) Fix overflow with bpf arrays, from Daniel Borkmann.
4) Fix RDMA regression with mlx5 due to mlx5 no longer using
pci_irq_get_affinity(), from Saeed Mahameed.
5) Missing RCU read locking in nl80211_send_iface() when it calls
ieee80211_bss_get_ie(), from Dominik Brodowski.
6) cfg80211 should check dev_set_name()'s return value, from Johannes
Berg.
7) Missing module license tag in 9p protocol, from Stephen Hemminger.
8) Fix crash due to too small MTU in udp ipv6 sendmsg, from Mike
Maloney.
9) Fix endless loop in netlink extack code, from David Ahern.
10) TLS socket layer sets inverted error codes, resulting in an endless
loop. From Robert Hering.
11) Revert openvswitch erspan tunnel support, it's mis-designed and we
need to kill it before it goes into a real release. From William Tu.
12) Fix lan78xx failures in full speed USB mode, from Yuiko Oshino.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (54 commits)
net, sched: fix panic when updating miniq {b,q}stats
qed: Fix potential use-after-free in qed_spq_post()
nfp: use the correct index for link speed table
lan78xx: Fix failure in USB Full Speed
sctp: do not allow the v4 socket to bind a v4mapped v6 address
sctp: return error if the asoc has been peeled off in sctp_wait_for_sndbuf
sctp: reinit stream if stream outcnt has been change by sinit in sendmsg
ibmvnic: Fix pending MAC address changes
netlink: extack: avoid parenthesized string constant warning
ipv4: Make neigh lookup keys for loopback/point-to-point devices be INADDR_ANY
net: Allow neigh contructor functions ability to modify the primary_key
sh_eth: fix dumping ARSTR
Revert "openvswitch: Add erspan tunnel support."
net/tls: Fix inverted error codes to avoid endless loop
ipv6: ip6_make_skb() needs to clear cork.base.dst
sctp: avoid compiler warning on implicit fallthru
net: ipv4: Make "ip route get" match iif lo rules again.
netlink: extack needs to be reset each time through loop
tipc: fix a memory leak in tipc_nl_node_get_link()
ipv6: fix udpv6 sendmsg crash caused by too small MTU
...
Yet a few small last-minute fixes that should sneak into 4.15:
- Removal of a spurious WARN_ON() triggered by syzkaller
- Fix for ioctl races in ALSA sequencer
- Two trivial HD-audio fixup entries
-----BEGIN PGP SIGNATURE-----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=JkyD
-----END PGP SIGNATURE-----
Merge tag 'sound-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A few small last-minute fixes that should sneak into 4.15:
- remove a spurious WARN_ON() triggered by syzkaller
- fix for ioctl races in ALSA sequencer
- two trivial HD-audio fixup entries"
* tag 'sound-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: seq: Make ioctls race-free
ALSA: pcm: Remove yet superfluous WARN_ON()
ALSA: hda - Apply the existing quirk to iMac 14,1
ALSA: hda - Apply headphone noise quirk for another Dell XPS 13 variant
- Bring back context level recursive protection in ring buffer.
The simpler counter protection failed, due to a path when
tracing with trace_clock_global() as it could not be reentrant
and depended on the ring buffer recursive protection to keep that
from happening.
- Prevent branch profiling when FORTIFY_SOURCE is enabled. It causes
50 - 60 MB in warning messages. Branch profiling should never be
run on production systems, so there's no reason that it needs to
be enabled with FORTIFY_SOURCE.
-----BEGIN PGP SIGNATURE-----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=qWqD
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.15-rc4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
- Bring back context level recursive protection in ring buffer.
The simpler counter protection failed, due to a path when tracing
with trace_clock_global() as it could not be reentrant and depended
on the ring buffer recursive protection to keep that from happening.
- Prevent branch profiling when FORTIFY_SOURCE is enabled.
It causes 50 - 60 MB in warning messages. Branch profiling should
never be run on production systems, so there's no reason that it
needs to be enabled with FORTIFY_SOURCE.
* tag 'trace-v4.15-rc4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Prevent PROFILE_ALL_BRANCHES when FORTIFY_SOURCE=y
ring-buffer: Bring back context level recursive checks
While working on fixing another bug, I ran into the following panic
on arm64 by simply attaching clsact qdisc, adding a filter and running
traffic on ingress to it:
[...]
[ 178.188591] Unable to handle kernel read from unreadable memory at virtual address 810fb501f000
[ 178.197314] Mem abort info:
[ 178.200121] ESR = 0x96000004
[ 178.203168] Exception class = DABT (current EL), IL = 32 bits
[ 178.209095] SET = 0, FnV = 0
[ 178.212157] EA = 0, S1PTW = 0
[ 178.215288] Data abort info:
[ 178.218175] ISV = 0, ISS = 0x00000004
[ 178.222019] CM = 0, WnR = 0
[ 178.224997] user pgtable: 4k pages, 48-bit VAs, pgd = 0000000023cb3f33
[ 178.231531] [0000810fb501f000] *pgd=0000000000000000
[ 178.236508] Internal error: Oops: 96000004 [#1] SMP
[...]
[ 178.311855] CPU: 73 PID: 2497 Comm: ping Tainted: G W 4.15.0-rc7+ #5
[ 178.319413] Hardware name: FOXCONN R2-1221R-A4/C2U4N_MB, BIOS G31FB18A 03/31/2017
[ 178.326887] pstate: 60400005 (nZCv daif +PAN -UAO)
[ 178.331685] pc : __netif_receive_skb_core+0x49c/0xac8
[ 178.336728] lr : __netif_receive_skb+0x28/0x78
[ 178.341161] sp : ffff00002344b750
[ 178.344465] x29: ffff00002344b750 x28: ffff810fbdfd0580
[ 178.349769] x27: 0000000000000000 x26: ffff000009378000
[...]
[ 178.418715] x1 : 0000000000000054 x0 : 0000000000000000
[ 178.424020] Process ping (pid: 2497, stack limit = 0x000000009f0a3ff4)
[ 178.430537] Call trace:
[ 178.432976] __netif_receive_skb_core+0x49c/0xac8
[ 178.437670] __netif_receive_skb+0x28/0x78
[ 178.441757] process_backlog+0x9c/0x160
[ 178.445584] net_rx_action+0x2f8/0x3f0
[...]
Reason is that sch_ingress and sch_clsact are doing mini_qdisc_pair_init()
which sets up miniq pointers to cpu_{b,q}stats from the underlying qdisc.
Problem is that this cannot work since they are actually set up right after
the qdisc ->init() callback in qdisc_create(), so first packet going into
sch_handle_ingress() tries to call mini_qdisc_bstats_cpu_update() and we
therefore panic.
In order to fix this, allocation of {b,q}stats needs to happen before we
call into ->init(). In net-next, there's already such option through commit
d59f5ffa59 ("net: sched: a dflt qdisc may be used with per cpu stats").
However, the bug needs to be fixed in net still for 4.15. Thus, include
these bits to reduce any merge churn and reuse the static_flags field to
set TCQ_F_CPUSTATS, and remove the allocation from qdisc_create() since
there is no other user left. Prashant Bhole ran into the same issue but
for net-next, thus adding him below as well as co-author. Same issue was
also reported by Sandipan Das when using bcc.
Fixes: 46209401f8 ("net: core: introduce mini_Qdisc and eliminate usage of tp->q for clsact fastpath")
Reference: https://lists.iovisor.org/pipermail/iovisor-dev/2018-January/001190.html
Reported-by: Sandipan Das <sandipan@linux.vnet.ibm.com>
Co-authored-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Co-authored-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to check if p_ent->comp_mode is QED_SPQ_MODE_EBLOCK before
calling qed_spq_add_entry(). The test is fine is the mode is EBLOCK,
but if it isn't then qed_spq_add_entry() might kfree(p_ent).
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sts variable is holding link speed as well as state. We should
be using ls to index into ls_to_ethtool.
Fixes: 265aeb511b ("nfp: add support for .get_link_ksettings()")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix initialize the uninitialized tx_qlen to an appropriate value when USB
Full Speed is used.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using dynamic stack_depth tracking in arm64 JIT is currently broken in
combination with tail calls. In prologue, we cache ctx->stack_size and
adjust SP reg for setting up function call stack, and tearing it down
again in epilogue. Problem is that when doing a tail call, the cached
ctx->stack_size might not be the same.
One way to fix the problem with minimal overhead is to re-adjust SP in
emit_bpf_tail_call() and properly adjust it to the current program's
ctx->stack_size. Tested on Cavium ThunderX ARMv8.
Fixes: f1c9eed7f4 ("bpf, arm64: take advantage of stack_depth tracking")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The check in sctp_sockaddr_af is not robust enough to forbid binding a
v4mapped v6 addr on a v4 socket.
The worse thing is that v4 socket's bind_verify would not convert this
v4mapped v6 addr to a v4 addr. syzbot even reported a crash as the v4
socket bound a v6 addr.
This patch is to fix it by doing the common sa.sa_family check first,
then AF_INET check for v4mapped v6 addrs.
Fixes: 7dab83de50 ("sctp: Support ipv6only AF_INET6 sockets.")
Reported-by: syzbot+7b7b518b1228d2743963@syzkaller.appspotmail.com
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit cea0cc80a6 ("sctp: use the right sk after waking up from
wait_buf sleep"), it may change to lock another sk if the asoc has been
peeled off in sctp_wait_for_sndbuf.
However, the asoc's new sk could be already closed elsewhere, as it's in
the sendmsg context of the old sk that can't avoid the new sk's closing.
If the sk's last one refcnt is held by this asoc, later on after putting
this asoc, the new sk will be freed, while under it's own lock.
This patch is to revert that commit, but fix the old issue by returning
error under the old sk's lock.
Fixes: cea0cc80a6 ("sctp: use the right sk after waking up from wait_buf sleep")
Reported-by: syzbot+ac6ea7baa4432811eb50@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After introducing sctp_stream structure, sctp uses stream->outcnt as the
out stream nums instead of c.sinit_num_ostreams.
However when users use sinit in cmsg, it only updates c.sinit_num_ostreams
in sctp_sendmsg. At that moment, stream->outcnt is still using previous
value. If it's value is not updated, the sinit_num_ostreams of sinit could
not really work.
This patch is to fix it by updating stream->outcnt and reiniting stream
if stream outcnt has been change by sinit in sendmsg.
Fixes: a83863174a ("sctp: prepare asoc stream for stream reconf")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For legacy chips without CLM blob files, kernel with user helper function
returns -EAGAIN when we request_firmware(), and then driver got failed
when bringing up legacy chips. We expect the CLM blob file for legacy chip
is not existence in firmware path, but the -ENOENT error is transferred to
-EAGAIN in firmware_class.c with user helper.
Because of that, we continue with CLM data currently present in firmware
if getting error from doing request_firmware().
Cc: stable@vger.kernel.org # v4.15.y
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since commit d41e6858ba ("MIPS: Kconfig: Set default MIPS system type
as generic") changed the default MIPS platform to the "generic"
platform, which uses PCI_DRIVERS_GENERIC instead of PCI_DRIVERS_LEGACY,
various files in drivers/ssb/ have failed to build.
This is particularly due to the existence of struct pci_controller being
dependent on PCI_DRIVERS_LEGACY since commit c5611df968 ("MIPS: PCI:
Introduce CONFIG_PCI_DRIVERS_LEGACY"), so add that dependency to Kconfig
to prevent these files being built for the "generic" platform including
all{yes,mod}config builds.
Fixes: c5611df968 ("MIPS: PCI: Introduce CONFIG_PCI_DRIVERS_LEGACY")
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: Michael Buesch <m@bues.ch>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-wireless@vger.kernel.org
Cc: linux-mips@linux-mips.org
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Mips builds with BCMA host mode enabled fail in mainline and -next
with:
In file included from include/linux/bcma/bcma.h:10:0,
from drivers/bcma/bcma_private.h:9,
from drivers/bcma/main.c:8:
include/linux/bcma/bcma_driver_pci.h:218:24: error:
field 'pci_controller' has incomplete type
Bisect points to commit d41e6858ba ("MIPS: Kconfig: Set default MIPS
system type as generic") as the culprit. Analysis shows that the commmit
changes PCI configuration and enables PCI_DRIVERS_GENERIC. This in turn
disables PCI_DRIVERS_LEGACY. 'struct pci_controller' is, however, only
defined if PCI_DRIVERS_LEGACY is enabled.
Ultimately that means that BCMA_DRIVER_PCI_HOSTMODE depends on
PCI_DRIVERS_LEGACY. Add the missing dependency.
Fixes: d41e6858ba ("MIPS: Kconfig: Set default MIPS system type as ...")
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: James Hogan <jhogan@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
KVM doesn't follow the SMCCC when it comes to unimplemented calls,
and inject an UNDEF instead of returning an error. Since firmware
calls are now used for security mitigation, they are becoming more
common, and the undef is counter productive.
Instead, let's follow the SMCCC which states that -1 must be returned
to the caller when getting an unknown function number.
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Due to architecture limitations, the IBM VNIC client driver is unable
to perform MAC address changes unless the device has "logged in" to
its backing device. Currently, pending MAC changes are handled before
login, resulting in an error and failure to change the MAC address.
Moving that chunk to the end of the ibmvnic_login function, when we are
sure that it was successful, fixes that.
The MAC address can be changed when the device is up or down, so
only check if the device is in a "PROBED" state before setting the
MAC address.
Fixes: c26eba03e4 ("ibmvnic: Update reset infrastructure to support tunable parameters")
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Reviewed-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some rare conditions when running one PEAK USB-FD interface over
a non high-speed USB controller, one useless USB fragment might be sent.
This patch fixes the way a USB command is fragmented when its length is
greater than 64 bytes and when the underlying USB controller is not a
high-speed one.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Before commit:
e33a9bba85 ("sched/core: move IO scheduling accounting from io_schedule_timeout() into scheduler")
delayacct_blkio_end() was called after context-switching into the task which
completed I/O.
This resulted in double counting: the task would account a delay both waiting
for I/O and for time spent in the runqueue.
With e33a9bba85, delayacct_blkio_end() is called by try_to_wake_up().
In ttwu, we have not yet context-switched. This is more correct, in that
the delay accounting ends when the I/O is complete.
But delayacct_blkio_end() relies on 'get_current()', and we have not yet
context-switched into the task whose I/O completed. This results in the
wrong task having its delay accounting statistics updated.
Instead of doing that, pass the task_struct being woken to delayacct_blkio_end(),
so that it can update the statistics of the correct task.
Signed-off-by: Josh Snyder <joshs@netflix.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Cc: <stable@vger.kernel.org>
Cc: Brendan Gregg <bgregg@netflix.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-block@vger.kernel.org
Fixes: e33a9bba85 ("sched/core: move IO scheduling accounting from io_schedule_timeout() into scheduler")
Link: http://lkml.kernel.org/r/1513613712-571-1-git-send-email-joshs@netflix.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently the BSP microcode update code examines the initrd very early
in the boot process. If SME is active, the initrd is treated as being
encrypted but it has not been encrypted (in place) yet. Update the
early boot code that encrypts the kernel to also encrypt the initrd so
that early BSP microcode updates work.
Tested-by: Gabriel Craciunescu <nix.or.die@gmail.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180110192634.6026.10452.stgit@tlendack-t1.amdoffice.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In preparation for encrypting more than just the kernel, the encryption
support in sme_encrypt_kernel() needs to support 4KB page aligned
encryption instead of just 2MB large page aligned encryption.
Update the routines that populate the PGD to support non-2MB aligned
addresses. This is done by creating PTE page tables for the start
and end portion of the address range that fall outside of the 2MB
alignment. This results in, at most, two extra pages to hold the
PTE entries for each mapping of a range.
Tested-by: Gabriel Craciunescu <nix.or.die@gmail.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180110192626.6026.75387.stgit@tlendack-t1.amdoffice.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In preparation for encrypting more than just the kernel during early
boot processing, centralize the use of the PMD flag settings based
on the type of mapping desired. When 4KB aligned encryption is added,
this will allow either PTE flags or large page PMD flags to be used
without requiring the caller to adjust.
Tested-by: Gabriel Craciunescu <nix.or.die@gmail.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180110192615.6026.14767.stgit@tlendack-t1.amdoffice.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In preparation for follow-on patches, combine the PGD mapping parameters
into a struct to reduce the number of function arguments and allow for
direct updating of the next pagetable mapping area pointer.
Tested-by: Gabriel Craciunescu <nix.or.die@gmail.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180110192605.6026.96206.stgit@tlendack-t1.amdoffice.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Clean up the use of PUSH and POP and when registers are saved in the
__enc_copy() assembly function in order to improve the readability of the code.
Move parameter register saving into general purpose registers earlier
in the code and move all the pushes to the beginning of the function
with corresponding pops at the end.
We do this to prepare fixes.
Tested-by: Gabriel Craciunescu <nix.or.die@gmail.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180110192556.6026.74187.stgit@tlendack-t1.amdoffice.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If a nonexistent file is supplied to objtool, it complains with a
non-helpful error:
open: No such file or directory
Improve it to:
objtool: Can't open 'foo': No such file or directory
Reported-by: Markus <M4rkusXXL@web.de>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/406a3d00a21225eee2819844048e17f68523ccf6.1516025651.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Objtool segfaults when the gold linker is used with
CONFIG_MODVERSIONS=y and CONFIG_UNWINDER_ORC=y.
With CONFIG_MODVERSIONS=y, the .o file gets passed to the linker before
being passed to objtool. The gold linker seems to strip unused ELF
symbols by default, which confuses objtool and causes the seg fault when
it's trying to generate ORC metadata.
Objtool should really be running immediately after GCC anyway, without a
linker call in between. Change the makefile ordering so that objtool is
called before the linker.
Reported-and-tested-by: Markus <M4rkusXXL@web.de>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: ee9f8fce99 ("x86/unwind: Add the ORC unwinder")
Link: http://lkml.kernel.org/r/355f04da33581f4a3bf82e5b512973624a1e23a2.1516025651.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The rdma_ah_find_type() accesses the port array based on an index
controlled by userspace. The existing bounds check is after the first use
of the index, so userspace can generate an out of bounds access, as shown
by the KASN report below.
==================================================================
BUG: KASAN: slab-out-of-bounds in to_rdma_ah_attr+0xa8/0x3b0
Read of size 4 at addr ffff880019ae2268 by task ibv_rc_pingpong/409
CPU: 0 PID: 409 Comm: ibv_rc_pingpong Not tainted 4.15.0-rc2-00031-gb60a3faf5b83-dirty #3
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.7.5-0-ge51488c-20140602_164612-nilsson.home.kraxel.org 04/01/2014
Call Trace:
dump_stack+0xe9/0x18f
print_address_description+0xa2/0x350
kasan_report+0x3a5/0x400
to_rdma_ah_attr+0xa8/0x3b0
mlx5_ib_query_qp+0xd35/0x1330
ib_query_qp+0x8a/0xb0
ib_uverbs_query_qp+0x237/0x7f0
ib_uverbs_write+0x617/0xd80
__vfs_write+0xf7/0x500
vfs_write+0x149/0x310
SyS_write+0xca/0x190
entry_SYSCALL_64_fastpath+0x18/0x85
RIP: 0033:0x7fe9c7a275a0
RSP: 002b:00007ffee5498738 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 00007fe9c7ce4b00 RCX: 00007fe9c7a275a0
RDX: 0000000000000018 RSI: 00007ffee5498800 RDI: 0000000000000003
RBP: 000055d0c8d3f010 R08: 00007ffee5498800 R09: 0000000000000018
R10: 00000000000000ba R11: 0000000000000246 R12: 0000000000008000
R13: 0000000000004fb0 R14: 000055d0c8d3f050 R15: 00007ffee5498560
Allocated by task 1:
__kmalloc+0x3f9/0x430
alloc_mad_private+0x25/0x50
ib_mad_post_receive_mads+0x204/0xa60
ib_mad_init_device+0xa59/0x1020
ib_register_device+0x83a/0xbc0
mlx5_ib_add+0x50e/0x5c0
mlx5_add_device+0x142/0x410
mlx5_register_interface+0x18f/0x210
mlx5_ib_init+0x56/0x63
do_one_initcall+0x15b/0x270
kernel_init_freeable+0x2d8/0x3d0
kernel_init+0x14/0x190
ret_from_fork+0x24/0x30
Freed by task 0:
(stack is not available)
The buggy address belongs to the object at ffff880019ae2000
which belongs to the cache kmalloc-512 of size 512
The buggy address is located 104 bytes to the right of
512-byte region [ffff880019ae2000, ffff880019ae2200)
The buggy address belongs to the page:
page:000000005d674e18 count:1 mapcount:0 mapping: (null) index:0x0 compound_mapcount: 0
flags: 0x4000000000008100(slab|head)
raw: 4000000000008100 0000000000000000 0000000000000000 00000001000c000c
raw: dead000000000100 dead000000000200 ffff88001a402000 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff880019ae2100: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff880019ae2180: 00 00 00 00 00 00 00 00 00 00 00 00 00 fc fc fc
>ffff880019ae2200: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^
ffff880019ae2280: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff880019ae2300: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
==================================================================
Disabling lock debugging due to kernel taint
Cc: <stable@vger.kernel.org>
Fixes: 44c58487d5 ("IB/core: Define 'ib' and 'roce' rdma_ah_attr types")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
NL_SET_ERR_MSG() and NL_SET_ERR_MSG_ATTR() lead to the following warning
in newer versions of gcc:
warning: array initialized from parenthesized string constant
Just remove the parentheses, they're not needed in this context since
anyway since there can be no operator precendence issues or similar.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jim Westfall says:
====================
ipv4: Make neigh lookup keys for loopback/point-to-point devices be INADDR_ANY
This used to be the previous behavior in older kernels but became broken in
a263b30936 (ipv4: Make neigh lookups directly in output packet path)
and then later removed because it was broken in 0bb4087cbe (ipv4: Fix neigh
lookup keying over loopback/point-to-point devices)
Not having this results in there being an arp entry for every remote ip
address that the device talks to. Given a fairly active device it can
cause the arp table to become huge and/or having to add/purge large number
of entires to keep within table size thresholds.
$ ip -4 neigh show nud noarp | grep tun | wc -l
55850
$ lnstat -k arp_cache:entries,arp_cache:allocs,arp_cache:destroys -c 10
arp_cach|arp_cach|arp_cach|
entries| allocs|destroys|
81493|620166816|620126069|
101867| 10186| 0|
113854| 5993| 0|
118773| 2459| 0|
27937| 18579| 63998|
39256| 5659| 0|
56231| 8487| 0|
65602| 4685| 0|
79697| 7047| 0|
90733| 5517| 0|
v2:
- fixes coding style issues
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Map all lookup neigh keys to INADDR_ANY for loopback/point-to-point devices
to avoid making an entry for every remote ip the device needs to talk to.
This used the be the old behavior but became broken in a263b30936
(ipv4: Make neigh lookups directly in output packet path) and later removed
in 0bb4087cbe (ipv4: Fix neigh lookup keying over loopback/point-to-point
devices) because it was broken.
Signed-off-by: Jim Westfall <jwestfall@surrealistic.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use n->primary_key instead of pkey to account for the possibility that a neigh
constructor function may have modified the primary_key value.
Signed-off-by: Jim Westfall <jwestfall@surrealistic.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
ARSTR is always located at the start of the TSU register region, thus
using add_reg() instead of add_tsu_reg() in __sh_eth_get_regs() to dump it
causes EDMR or EDSR (depending on the register layout) to be dumped instead
of ARSTR. Use the correct condition/macro there...
Fixes: 6b4b4fead3 ("sh_eth: Implement ethtool register dump operations")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit ceaa001a17.
The OVS_TUNNEL_KEY_ATTR_ERSPAN_OPTS attr should be designed
as a nested attribute to support all ERSPAN v1 and v2's fields.
The current attr is a be32 supporting only one field. Thus, this
patch reverts it and later patch will redo it using nested attr.
Signed-off-by: William Tu <u9012063@gmail.com>
Cc: Jiri Benc <jbenc@redhat.com>
Cc: Pravin Shelar <pshelar@ovn.org>
Acked-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
sendfile() calls can hang endless with using Kernel TLS if a socket error occurs.
Socket error codes must be inverted by Kernel TLS before returning because
they are stored with positive sign. If returned non-inverted they are
interpreted as number of bytes sent, causing endless looping of the
splice mechanic behind sendfile().
Signed-off-by: Robert Hering <r.hering@avm.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In my last patch, I missed fact that cork.base.dst was not initialized
in ip6_make_skb() :
If ip6_setup_cork() returns an error, we might attempt a dst_release()
on some random pointer.
Fixes: 862c03ee1d ("ipv6: fix possible mem leaks in ipv6_make_skb()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I regularly get 50 MB - 60 MB files during kernel randconfig builds.
These large files mostly contain (many repeats of; e.g., 124,594):
In file included from ../include/linux/string.h:6:0,
from ../include/linux/uuid.h:20,
from ../include/linux/mod_devicetable.h:13,
from ../scripts/mod/devicetable-offsets.c:3:
../include/linux/compiler.h:64:4: warning: '______f' is static but declared in inline function 'strcpy' which is not static [enabled by default]
______f = { \
^
../include/linux/compiler.h:56:23: note: in expansion of macro '__trace_if'
^
../include/linux/string.h:425:2: note: in expansion of macro 'if'
if (p_size == (size_t)-1 && q_size == (size_t)-1)
^
This only happens when CONFIG_FORTIFY_SOURCE=y and
CONFIG_PROFILE_ALL_BRANCHES=y, so prevent PROFILE_ALL_BRANCHES if
FORTIFY_SOURCE=y.
Link: http://lkml.kernel.org/r/9199446b-a141-c0c3-9678-a3f9107f2750@infradead.org
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
These fall-through are expected.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3765d35ed8 ("net: ipv4: Convert inet_rtm_getroute to rcu
versions of route lookup") broke "ip route get" in the presence
of rules that specify iif lo.
Host-originated traffic always has iif lo, because
ip_route_output_key_hash and ip6_route_output_flags set the flow
iif to LOOPBACK_IFINDEX. Thus, putting "iif lo" in an ip rule is a
convenient way to select only originated traffic and not forwarded
traffic.
inet_rtm_getroute used to match these rules correctly because
even though it sets the flow iif to 0, it called
ip_route_output_key which overwrites iif with LOOPBACK_IFINDEX.
But now that it calls ip_route_output_key_hash_rcu, the ifindex
will remain 0 and not match the iif lo in the rule. As a result,
"ip route get" will return ENETUNREACH.
Fixes: 3765d35ed8 ("net: ipv4: Convert inet_rtm_getroute to rcu versions of route lookup")
Tested: https://android.googlesource.com/kernel/tests/+/master/net/test/multinetwork_test.py passes again
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot triggered the WARN_ON in netlink_ack testing the bad_attr value.
The problem is that netlink_rcv_skb loops over the skb repeatedly invoking
the callback and without resetting the extack leaving potentially stale
data. Initializing each time through avoids the WARN_ON.
Fixes: 2d4bc93368 ("netlink: extended ACK reporting")
Reported-by: syzbot+315fa6766d0f7c359327@syzkaller.appspotmail.com
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When tipc_node_find_by_name() fails, the nlmsg is not
freed.
While on it, switch to a goto label to properly
free it.
Fixes: be9c086715c ("tipc: narrow down exposure of struct tipc_node")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver lacks a MODULE_LICENSE tag, leading to a Kbuild warning:
WARNING: modpost: missing MODULE_LICENSE() in drivers/net/ethernet/cirrus/cs89x0.o
This adds license, author, and description according to the
comment block at the start of the file.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
ppp_dev_uninit(), which is the .ndo_uninit() handler of PPP devices,
needs to lock pn->all_ppp_mutex. Therefore we mustn't call
register_netdevice() with pn->all_ppp_mutex already locked, or we'd
deadlock in case register_netdevice() fails and calls .ndo_uninit().
Fortunately, we can unlock pn->all_ppp_mutex before calling
register_netdevice(). This lock protects pn->units_idr, which isn't
used in the device registration process.
However, keeping pn->all_ppp_mutex locked during device registration
did ensure that no device in transient state would be published in
pn->units_idr. In practice, unlocking it before calling
register_netdevice() doesn't change this property: ppp_unit_register()
is called with 'ppp_mutex' locked and all searches done in
pn->units_idr hold this lock too.
Fixes: 8cb775bc0a ("ppp: fix device unregistration upon netns deletion")
Reported-and-tested-by: syzbot+367889b9c9e279219175@syzkaller.appspotmail.com
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This explains why is the net usage of __ptr_ring_peek
actually ok without locks.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 9P of Xen module is missing required license and module information.
See https://bugzilla.kernel.org/show_bug.cgi?id=198109
Reported-by: Alan Bartlett <ajb@elrepo.org>
Fixes: 868eb12273 ("xen/9pfs: introduce Xen 9pfs transport driver")
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1a149d7d3f ("ring-buffer: Rewrite trace_recursive_(un)lock() to be
simpler") replaced the context level recursion checks with a simple counter.
This would prevent the ring buffer code from recursively calling itself more
than the max number of contexts that exist (Normal, softirq, irq, nmi). But
this change caused a lockup in a specific case, which was during suspend and
resume using a global clock. Adding a stack dump to see where this occurred,
the issue was in the trace global clock itself:
trace_buffer_lock_reserve+0x1c/0x50
__trace_graph_entry+0x2d/0x90
trace_graph_entry+0xe8/0x200
prepare_ftrace_return+0x69/0xc0
ftrace_graph_caller+0x78/0xa8
queued_spin_lock_slowpath+0x5/0x1d0
trace_clock_global+0xb0/0xc0
ring_buffer_lock_reserve+0xf9/0x390
The function graph tracer traced queued_spin_lock_slowpath that was called
by trace_clock_global. This pointed out that the trace_clock_global() is not
reentrant, as it takes a spin lock. It depended on the ring buffer recursive
lock from letting that happen.
By removing the context detection and adding just a max number of allowable
recursions, it allowed the trace_clock_global() to be entered again and try
to retake the spinlock it already held, causing a deadlock.
Fixes: 1a149d7d3f ("ring-buffer: Rewrite trace_recursive_(un)lock() to be simpler")
Reported-by: David Weinehall <david.weinehall@gmail.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
i830_disable_pipe() gets called from the power well code, and thus
we're already holding the power domain mutex. That means we can't
call plane->get_hw_state() as it will also try to grab the
same mutex and will thus deadlock.
Replace the assert_plane() calls (which calls ->get_hw_state()) with
just raw register reads in i830_disable_pipe(). As a bonus we can
now get a warning if plane C is enabled even though we don't even
expose it as a drm plane.
v2: Do a separate WARN_ON() for each plane (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Fixes: d87ce76402 ("drm/i915: Add .get_hw_state() method for planes")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171129125411.29055-1-ville.syrjala@linux.intel.com
(cherry picked from commit 5816d9cbc0)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Unify the plane disabling during state readout by pulling the code into
a new helper intel_plane_disable_noatomic(). We'll also read out the
state of all planes, so that we know which planes really need to be
diabled.
Additonally we change the plane<->pipe mapping sanitation to work by
simply disabling the offending planes instead of entire pipes. And
we do it before we otherwise sanitize the crtcs, which means we don't
have to worry about misassigned planes during crtc sanitation anymore.
v2: Reoder patches to not depend on enum old_plane_id
v3: s/for_each_pipe/for_each_intel_crtc/
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alex Villacís Lasso <alexvillacislasso@hotmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103223
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Thierry Reding <thierry.reding@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171117191917.11506-3-ville.syrjala@linux.intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
(cherry picked from commit b1e01595a6)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Add a .get_hw_state() method for planes, returning true or false
depending on whether the plane is enabled. Use it to rewrite the
plane enabled/disabled asserts in platform agnostic fashion.
We do lose the pre-gen4 plane<->pipe mapping checks, but since we're
supposed sanitize that anyway it doesn't really matter.
v2: Reoder patches to not depend on enum old_plane_id
Just call assert_plane_disabled() from assert_planes_disabled()
v3: Deal with disabled power wells in .get_hw_state()
v4: Rebase due skl primary plane code removal
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alex Villacís Lasso <alexvillacislasso@hotmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> #v2
Tested-by: Thierry Reding <thierry.reding@gmail.com> #v2
Link: https://patchwork.freedesktop.org/patch/msgid/20171117191917.11506-2-ville.syrjala@linux.intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
(cherry picked from commit 51f5a09639)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Commit 5143c953a7 ("mmc: sdhci-esdhc-imx: Allow all supported
prescaler values") made it possible to set SYSCTL.SDCLKFS to 0 in SDR
mode, thus bypassing the SD clock frequency prescaler, in order to be
able to get higher SD clock frequencies in some contexts. However, that
commit missed the fact that this value is illegal on the eSDHCv3
instance of the i.MX53. This seems to be the only exception on i.MX,
this value being legal even for the eSDHCv2 instances of the i.MX53.
Fix this issue by changing the minimum prescaler value if the i.MX53
eSDHCv3 is detected. According to the i.MX53 reference manual, if
DLLCTRL[10] can be set, then the controller is eSDHCv3, else it is
eSDHCv2.
This commit fixes the following issue, which was preventing the i.MX53
Loco (IMX53QSB) board from booting Linux 4.15.0-rc5:
[ 1.882668] mmcblk1: error -84 transferring data, sector 2048, nr 8, cmd response 0x900, card status 0xc00
[ 2.002255] mmcblk1: error -84 transferring data, sector 2050, nr 6, cmd response 0x900, card status 0xc00
[ 12.645056] mmc1: Timeout waiting for hardware interrupt.
[ 12.650473] mmc1: sdhci: ============ SDHCI REGISTER DUMP ===========
[ 12.656921] mmc1: sdhci: Sys addr: 0x00000000 | Version: 0x00001201
[ 12.663366] mmc1: sdhci: Blk size: 0x00000004 | Blk cnt: 0x00000000
[ 12.669813] mmc1: sdhci: Argument: 0x00000000 | Trn mode: 0x00000013
[ 12.676258] mmc1: sdhci: Present: 0x01f8028f | Host ctl: 0x00000013
[ 12.682703] mmc1: sdhci: Power: 0x00000002 | Blk gap: 0x00000000
[ 12.689148] mmc1: sdhci: Wake-up: 0x00000000 | Clock: 0x0000003f
[ 12.695594] mmc1: sdhci: Timeout: 0x0000008e | Int stat: 0x00000000
[ 12.702039] mmc1: sdhci: Int enab: 0x107f004b | Sig enab: 0x107f004b
[ 12.708485] mmc1: sdhci: AC12 err: 0x00000000 | Slot int: 0x00001201
[ 12.714930] mmc1: sdhci: Caps: 0x07eb0000 | Caps_1: 0x08100810
[ 12.721375] mmc1: sdhci: Cmd: 0x0000163a | Max curr: 0x00000000
[ 12.727821] mmc1: sdhci: Resp[0]: 0x00000920 | Resp[1]: 0x00000000
[ 12.734265] mmc1: sdhci: Resp[2]: 0x00000000 | Resp[3]: 0x00000000
[ 12.740709] mmc1: sdhci: Host ctl2: 0x00000000
[ 12.745157] mmc1: sdhci: ADMA Err: 0x00000001 | ADMA Ptr: 0xc8049200
[ 12.751601] mmc1: sdhci: ============================================
[ 12.758110] print_req_error: I/O error, dev mmcblk1, sector 2050
[ 12.764135] Buffer I/O error on dev mmcblk1p1, logical block 0, lost sync page write
[ 12.775163] EXT4-fs (mmcblk1p1): mounted filesystem without journal. Opts: (null)
[ 12.782746] VFS: Mounted root (ext4 filesystem) on device 179:9.
[ 12.789151] mmcblk1: response CRC error sending SET_BLOCK_COUNT command, card status 0x900
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Reported-by: Wladimir J. van der Laan <laanwj@gmail.com>
Tested-by: Wladimir J. van der Laan <laanwj@gmail.com>
Fixes: 5143c953a7 ("mmc: sdhci-esdhc-imx: Allow all supported prescaler values")
Cc: <stable@vger.kernel.org> # v4.13+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
