i.MX7ULP's ARM core clock design is totally different compared
with i.MX7D/8M SoCs which supported by imx-cpufreq-dt. It needs
get_intermediate and target_intermedate to configure clk MUX ready,
before let OPP configure ARM core clk.
|---FIRC
|------RUN---...---SCS(MUX2) --------|
ARM --(MUX1) |---SPLL_PFD0(CLK_SET_RATE_GATE)
|------HSRUN--...--HSRUN_SCS(MUX3)---|
|---SRIC
FIRC is step clk, SPLL_PFD0 is the normal clk driving ARM core.
MUX2 and MUX3 share same inputs. So if MUX2/MUX3 both sources from
SPLL_PFD0, both MUXes will lose input when configure SPLL_PFD0.
So the target_intermediate will configure MUX2/MUX3 to FIRC, to avoid
ARM core lose clk when configure SPLL_PFD0.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The cpufreq-dt driver allows cpufreq driver enabled without valid
regulator assigned, however, all i.MX platforms using cpufreq-dt
driver now require valid regulator, add "cpu-supply" property check
to avoid i.MX platforms' cpufreq enabled without valid regulator
and lead to system unstable.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Add i.MX8MP cpufreq DT support for speed grading and market
segment check.
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
[ Viresh: Minor formatting fixes ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
i.MX8MN has different speed grade definition compared to
i.MX8MQ/i.MX8MM, when fuses are NOT written, the default
speed_grade should be set to minimum available OPP defined
in DT which is 1.2GHz, the corresponding speed_grade value
should be 0xb.
Fixes: 5b8010ba70 ("cpufreq: imx-cpufreq-dt: Add i.MX8MN support")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
i.MX8MN is a new SoC of i.MX8M series, it also uses speed
grading and market segment fuses for OPP definitions, add
support for this SoC.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This is not currently needed, instead a platform device is always created
from SOC-specific code.
We can use of_machine_is_compatible for per-SOC behavior instead.
Suggested-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Early samples without fuses written report "0 0" which means consumer
segment and minimum speed grading. According to datasheet the minimum speed
grade is not supported for consumer parts so all OPPs are disabled
which results in stack dumps later on.
Fix by clamping minimum consumer speed grade to 1 on imx8mm and imx8mq.
Fixes: 4d28ba1d62 ("cpufreq: Add imx-cpufreq-dt driver")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
[ Viresh: s/minumum/minimum/ in patch and log ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Right now in upstream imx8m cpufreq support just lists a common subset
of OPPs because the higher ones should only be attempted after checking
speed grading in fuses.
Add a small driver which checks speed grading from nvmem cells before
registering cpufreq-dt.
This driver allows unlocking all frequencies for imx8mm and imx8mq and
could be applied to other chips like imx7d
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
