Move the hardware PMD and PTE page table definitions from pgtable.h
into pgtable-hwdef.h, and include pgtable-hwdef.h as necessary.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch removes TLB related codes in nommu mode.
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The enable_hlt and disable_hlt should be declared in
include/asm/setup.h. This fixes sparse errors from
arch/arm/kernel/process.c
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch removes the reliance of iwmmxt on hand coded alignments.
Since thread_info is always 8K aligned, specifying that fpstate is
8-byte aligned achieves the same effect without needing to resort
to hand coded alignments.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
Chapter B2.7.3 in the latest ARM ARM (with v6 information) states that
the completion of a TLB maintenance operation is only guaranteed by
the execution of a DSB (Data Syncronization Barrier, formerly Data
Write Barrier or Drain Write Buffer).
Note that a DSB is only needed in the flush_tlb_kernel_* functions
since the completion is guaranteed by a mode change (i.e. switching
back to user mode) for the flush_tlb_user_* functions.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch adds the at91_set_multi_drive() function to enable/disable
the multi-drive (open collector) pin capability on the AT91RM9200
processor.
This is necessary to fix the UDC (USB Gadget) driver for the AT91RM9200
board as it will not allow the board reset line to be pulled low if the
pullup is not driven as an open collector output as the boards are wired
to the USB connector on both the DK/EK.
This version of the patch updates it to 2.6.16-rc4.
Orignal patch by Jeff Warren.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Alessandro Zummo
The I2C pin assignment for the Iomega NAS100d board was incorrect. This
patch fixes it. The correct assignment has now been tested using the
new RTC class and a new driver for the RTC on the NAS100d.
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
With EABI the multiplex sys_ipc and sys_socketcall syscalls are
unavailable and their support code even removed from the compiled
kernel, and the new unmuxed syscalls must be used instead.
Make those syscall numbers visible.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A change to the SMP initialisation caused the following oops:
CPU1: Booted secondary processor
CPU1: D VIPT write-back cache
CPU1: I cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
CPU1: D cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
<7>Calibrating delay loop... 83.14 BogoMIPS (lpj=415744)
<1>Unable to handle kernel NULL pointer dereference at virtual address 0000001c
...
PC is at enqueue_task+0x1c/0x64
LR is at activate_task+0xcc/0xe4
SMP initialisation now requires cpu_possible_map to be initialised in
setup_arch(). Move this from smp_prepare_cpus() to smp_init_cpus()
and call it from our setup_arch() if CONFIG_SMP is enabled.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make new MADV_REMOVE, MADV_DONTFORK, MADV_DOFORK consistent across all
arches. The idea is to make it possible to use them portably even before
distros include them in libc headers.
Move common flags to asm-generic/mman.h
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently, copy-on-write may change the physical address of a page even if the
user requested that the page is pinned in memory (either by mlock or by
get_user_pages). This happens if the process forks meanwhile, and the parent
writes to that page. As a result, the page is orphaned: in case of
get_user_pages, the application will never see any data hardware DMA's into
this page after the COW. In case of mlock'd memory, the parent is not getting
the realtime/security benefits of mlock.
In particular, this affects the Infiniband modules which do DMA from and into
user pages all the time.
This patch adds madvise options to control whether memory range is inherited
across fork. Useful e.g. for when hardware is doing DMA from/into these
pages. Could also be useful to an application wanting to speed up its forks
by cutting large areas out of consideration.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Acked-by: Hugh Dickins <hugh@veritas.com>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Ben Dooks
Define the bits for the two board control latches
that control various items on the H1940 iPAQ.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch adds the missing cache flushes to common low-level
init that are needed to access the IO region. These flushes
are normally done at the end of devicemaps_init(), but we
need to detect the OMAP core type early.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
Since:
if (unlikely(__res || __ex_flag))
produces worse code on ARM than:
if (unlikely(__res | __ex_flag))
I therefore made it more explicit:
__res |= __ex_flag;
if (unlikely(__res != 0))
so it is not seen as a typo again.
Also made everything static inline rather than macros for better readability
(both produce the same code after all).
And finally added missing \t from multi-line assembly code.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lucas Correia Villa Real
This patch adds support to GPIO on the S3C2400, which is going to
be used by the GP32 machine and the SMDK2400 development board.
Signed-off-by: Lucas Correia Villa Real <lucasvr@gobolinux.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
ip_fast_csum() accesses memory via a pointer (iph) within an
asm function. To prevent memory corruption when the function is
inlined, it needs "memory" on the clobber list.
This fixes ip checksum errors reported by a Zaurus user.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from George G. Davis
This Freescale Semiconductor, Inc. contributed patch adds mem_types[]
support for ARMv6 non-shared device memory region attributes. This
implementation provides support for only first level section mapped
non-shared devices. Second level non-shared device mappings are not
yet supported.
Signed-off-by: George G. Davis <gdavis@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lucas Correia Villa Real
This patch defines S3C2400 memory map and adds a S3C24XX macro for
common resources between S3C2400, S3C2410 and S3C2440 cpus.
Signed-off-by: Lucas Correia Villa Real <lucasvr@gobolinux.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from David Vrabel
PXA27x SSP controller has a few different registers, including SCR (serial clock rate) in SSCR0.
Signed-off-by: David Vrabel <dvrabel@arcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes OMAP clock framework to use clk_enable/disable
instead of clk_use/unuse as specified in include/linux/clk.h.
Instances of clk_use/unuse are renamed to clk_enable/disable,
and references clk_use/unuse are removed.
Signed-off-by: Tony Lindgren <tony@atomide.com>
asm/mach/arch.h introduced a __deprecated, but didn't include compiler.h,
causing:
In file included from arch/arm/mach-at91rm9200/devices.c:13:
include/asm/mach/arch.h:23: warning: no semicolon at end of struct or union
include/asm/mach/arch.h:23: error: syntax error before 'phys_ram'
include/asm/mach/arch.h:34: error: syntax error before ':' token
include/asm/mach/arch.h:35: error: syntax error before ':' token
include/asm/mach/arch.h:36: error: syntax error before ':' token
include/asm/mach/arch.h:37: error: syntax error before ':' token
include/asm/mach/arch.h:45: error: syntax error before '}' token
Add the necessary include.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
This is needed by strace to properly handle the tracing of some system
calls. It could be useful for other applications as well.
Based on an earlier patch from Daniel Jacobowitz.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Daniel Jacobowitz <dan@debian.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
This patch adds the required code to support both user space ABIs at
the same time. A second syscall table is created to include legacy ABI
syscalls that need an ABI compat wrapper.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
struct statfs64 has extra padding with EABI growing its size from 84 to
88. This struct is now __attribute__((packed,aligned(4))) with a small
assembly wrapper to force the sz argument to 84 if it is 88 to avoid
copying the extra padding over user space memory unexpecting it.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
Fix a few syscalls for EABI requirements. They were sys_pread64 and
sys_pwrite64 where the last argument is now entirely pushed on stack,
but since commit 567bd98017 they don't
require any fixup. Remains only the stat64 structure. Non EABI kernels
are unaffected.
Signed-off-by: Nicolas Pitre
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
For a while we wanted to change the way syscalls were called on ARM.
Instead of encoding the syscall number in the swi instruction which
requires reading back the instruction from memory to extract that number
and polluting the data cache, it was decided that simply storing the
syscall number into r7 would be more efficient. Since this represents
an ABI change then making that change at the same time as EABI support
is the right thing to do.
It is now expected that EABI user space binaries put the syscall number
into r7 and use "swi 0" to call the kernel. Syscall register argument
are also expected to have "EABI arrangement" i.e. 64-bit arguments
should be put in a pair of registers from an even register number.
Example with long ftruncate64(unsigned int fd, loff_t length):
legacy ABI:
- put fd into r0
- put length into r1-r2
- use "swi #(0x900000 + 194)" to call the kernel
new ARM EABI:
- put fd into r0
- put length into r2-r3 (skipping over r1)
- put 194 into r7
- use "swi 0" to call the kernel
Note that it is important to use 0 for the swi argument as backward
compatibility with legacy ABI user space relies on this.
The syscall macros in asm-arm/unistd.h were also updated to support
both ABIs and implement the right call method automatically.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
The ARM EABI says that the stack pointer has to be 64-bit aligned for
reasons already mentioned in patch #3101 when calling C functions.
We therefore must verify and adjust sp accordingly when taking an
exception from kernel mode since sp might not necessarily be 64-bit
aligned if the exception occurs in the middle of a kernel function.
If the exception occurs while in user mode then no sp fixup is needed as
long as sizeof(struct pt_regs) as well as any additional syscall data
stack space remain multiples of 8.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
Although ARM is still using 32-bit pointers, version 5 and later
versions of the ARM architecture introduced the ldrd and strd
instructions to move 64-bit data which must be 64-bit aligned in memory,
and the EABI includes new constraints on structure data alignment to
allow for the compiler to use those instructions. This means that any
slab allocation must start on a 64-bit boundary which is not equivalent
to BYTES_PER_WORD, especially on those architecture versions that
implements the ldrd/strd instructions.
Overriding the default alignment disables some slab debug features. If
those debug features are really needed then the kernel will have to be
compiled for version 4 of the ARM architecture.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch supports start_thread in nommu mode which requires the
base index register.
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
This field is redundent since it must be equal to PHYS_OFFSET anyway.
Now that no code uses it anymore, mark it deprecated and remove all
initializations from the tree.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
For the ixp2000 netdev driver, we need to map in a chunk of SRAM (to
store the transmit and receive descriptors) and the scratch get/put
area (so that we can use the scratchpad rings in the cpu for managing
the descriptors.) These are the final two mappings needed for the
netdev driver and the last missing piece for the driver in mainline
to work.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
{get,put}_thread_info() were introduced in 2.5.4 and never
had been called by anything in the tree.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add per-arch sched_cacheflush() which is a write-back cacheflush used by
the migration-cost calibration code at bootup time.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Kevin Hilman
This patch increase available DMA-consistent memory allocated by dma_coherent_alloc(). The default remains at 2M (defined in asm/memory.h) and each platform has the ability to override in asm/arch-foo/memory.h.
Signed-off-by: Kevin Hilman <kevin@hilman.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
Depending on your gcc version, the current C-only implementation would
produce suboptimal code, ranging from a bad register selection forcing
an additional mov instruction to a failure to merge the eor and the ror
in a single instruction. With a little help gcc always produces the
best code.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch adds support to the 2.6 kernel series for the Atmel
AT91RM9200 processor.
This patch is the Serial driver.
This version uses the newly re-written GPL'ed hardware headers.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Most arches copied the i386 ioctl.h. Combine them into a generic header.
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
add the ARM version of mutex.h, which is optimized in assembly for
ARMv6, and uses the xchg implementation on pre-ARMv6.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
add atomic_xchg() to all the architectures. Needed by the new mutex code.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Patch from Deepak Saxena
In working on adding 36-bit addressed supersection support to ioremap(),
I came to the conclusion that it would be far simpler to do so by just
splitting __ioremap() into a main external interface and adding an
__ioremap_pfn() function that takes a pfn + offset into the page that
__ioremap() can call. This way existing callers of __ioremap() won't have
to change their code and 36-bit systems will just call __ioremap_pfn()
and we will not have to deal with unsigned long long variables.
Note that __ioremap_pfn() should _NOT_ be called directly by drivers
but is reserved for use by arch_ioremap() implementations that map
32-bit resource regions into the real 36-bit address and then call
this new function.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from SAN People
Following changes were made to clock.c:
1) Replaced <asm/hardware/clock.h> with <linux/clk.h>
2) Removed old unused clk_enable & clk_disable.
3) Replaced clk_use/clk_unuse with clk_enable/clk_disable.
Otherwise it's the same as the previous patch.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some ARM platforms have the ability to program the interrupt controller to
detect various interrupt edges and/or levels. For some platforms, this is
critical to setup correctly, particularly those which the setting is dependent
on the device.
Currently, ARM drivers do (eg) the following:
err = request_irq(irq, ...);
set_irq_type(irq, IRQT_RISING);
However, if the interrupt has previously been programmed to be level sensitive
(for whatever reason) then this will cause an interrupt storm.
Hence, if we combine set_irq_type() with request_irq(), we can then safely set
the type prior to unmasking the interrupt. The unfortunate problem is that in
order to support this, these flags need to be visible outside of the ARM
architecture - drivers such as smc91x need these flags and they're
cross-architecture.
Finally, the SA_TRIGGER_* flag passed to request_irq() should reflect the
property that the device would like. The IRQ controller code should do its
best to select the most appropriate supported mode.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Most of the architectures have the same asm/futex.h. This consolidates them
into asm-generic, with the arches including it from their own asm/futex.h.
In the case of UML, this reverts the old broken futex.h and goes back to using
the same one as almost everyone else.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Kill L1_CACHE_SHIFT from all arches. Since L1_CACHE_SHIFT_MAX is not used
anymore with the introduction of INTERNODE_CACHE, kill L1_CACHE_SHIFT_MAX.
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
EPXA10DB seems to be uncared for:
- the "PLD" code has never been merged
- no one has reported that this platform has been broken since
at least 2.6.10
- interest seems to have dried up around March 2003.
Therefore, remove EPXA10DB support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since the ARM AMBA bus is used on MIPS as well as ARM, we need
to make the bus available for other architectures to use. Move
the AMBA include files from include/asm-arm/hardware/ to
include/linux/amba/
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andre McCurdy
Replaces generic swab32 routine with a more ARM friendly version.
Reduces kernel text size by approx 1200 bytes when compiled with
3.4.4 and approx 2400 bytes with 4.0.2
Probably some performance benefit as well.
Signed-off-by: Andre McCurdy <armccurdy@yahoo.co.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Several counters already have the need to use 64 atomic variables on 64 bit
platforms (see mm_counter_t in sched.h). We have to do ugly ifdefs to fall
back to 32 bit atomic on 32 bit platforms.
The VM statistics patch that I am working on will also make more extensive
use of atomic64.
This patch introduces a new type atomic_long_t by providing definitions in
asm-generic/atomic.h that works similar to the c "long" type. Its 32 bits
on 32 bit platforms and 64 bits on 64 bit platforms.
Also cleans up the determination of the mm_counter_t in sched.h.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Here is the patch to implement madvise(MADV_REMOVE) - which frees up a
given range of pages & its associated backing store. Current
implementation supports only shmfs/tmpfs and other filesystems return
-ENOSYS.
"Some app allocates large tmpfs files, then when some task quits and some
client disconnect, some memory can be released. However the only way to
release tmpfs-swap is to MADV_REMOVE". - Andrea Arcangeli
Databases want to use this feature to drop a section of their bufferpool
(shared memory segments) - without writing back to disk/swap space.
This feature is also useful for supporting hot-plug memory on UML.
Concerns raised by Andrew Morton:
- "We have no plan for holepunching! If we _do_ have such a plan (or
might in the future) then what would the API look like? I think
sys_holepunch(fd, start, len), so we should start out with that."
- Using madvise is very weird, because people will ask "why do I need to
mmap my file before I can stick a hole in it?"
- None of the other madvise operations call into the filesystem in this
manner. A broad question is: is this capability an MM operation or a
filesytem operation? truncate, for example, is a filesystem operation
which sometimes has MM side-effects. madvise is an mm operation and with
this patch, it gains FS side-effects, only they're really, really
significant ones."
Comments:
- Andrea suggested the fs operation too but then it's more efficient to
have it as a mm operation with fs side effects, because they don't
immediatly know fd and physical offset of the range. It's possible to
fixup in userland and to use the fs operation but it's more expensive,
the vmas are already in the kernel and we can use them.
Short term plan & Future Direction:
- We seem to need this interface only for shmfs/tmpfs files in the short
term. We have to add hooks into the filesystem for correctness and
completeness. This is what this patch does.
- In the future, plan is to support both fs and mmap apis also. This
also involves (other) filesystem specific functions to be implemented.
- Current patch doesn't support VM_NONLINEAR - which can be addressed in
the future.
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Andrea Arcangeli <andrea@suse.de>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Jared Hulbert
The following patch changes the bus arbiter controller settings
for the Intel PXA27x Application Processor Family. Up to 5%
better video performance. It parks the bus on the core while not
in use and sets the arbitration for other bus items. The patch
only applies changes to the Intel Mainstone development platform.
This patch is not compatible with preproduction Intel PXA27x
silicon.
This patch is based on the Intel Linux Preview Kit released to the
public on 25 Feb. 2005 found at
ftp://ftp.arm.linux.org.uk/pub/linux/arm/people/xscale/mainstone/02-25-2005/.
Signed-off-by: Justin A Treon <justin_treon@yahoo.com>
Signed-off-by: Jared Hulbert <jaredeh@gmail.com>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
The expansion bus on the IXP46x NPU can be configured for either 32MiB or
16MiB windows and changing the configuration causes the base address for
each chip select for each region to change. Because of this, we cannot
hardcode the physical base as we currently do. This patch checks the
expansion bus configuration registers at runtime to determine the
appropriate window size. Note that this requires that the bootloader
already configured the device sizes appropriately, but I feel that is
valid assumption to make as the bootloader must configure and access
the flash window, the output display (LCD, LEDs, etc) window, and
other expansion bus devices.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
This patch moves a large chunk of the sharpsl_pm driver to
arch/arm/common so that it can be reused on other devices such as the
SL-5500 (collie). It also abstracts some functions from the core into
the machine and platform specific parts of the driver to aid reuse.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
To allow multiple platforms to use the PXA27x OHCI driver, the platform
code needs to be moved into the board specific files in
arch/arm/mach-pxa. This patch does this for mainstone and adds
preliminary hooks to allow other boards to use the driver.
This has been compile tested for mainstone and successfully run on Spitz
(Sharp Zaurus SL-C3000) with the addition of an appropriate board
support file.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch from Lennert Buytenhek
Add symbolic names for the five ixp2400 GPIO lines on the enp2611
that are used as interrupts.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
In its interrupt handler, the (NAPI) ixp2000 netdev driver needs to use
the masked thread interrupt status register (instead of the raw one) to
prevent scheduling polling when polling is already running when a TXdone
interrupt comes in. The definitions for the masked status registers were
not in yet, so this patch adds them.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Remove the ixdp2x01 cs89x0 hack from ixp2000's io implementation.
Since the cs89x0 driver has been made properly aware of the odd way
the cs89x0 is hooked up on the ixdp2x01, we don't need this hack
anymore.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Rod Whitby
PAGE_SHIFT is undeclared in include/asm-arm/arch-ixp4xx/memory.h, identified by the following kernel compilation error:
CC [M] sound/core/memory.o
In file included from include/asm/memory.h:27,
from include/asm/io.h:28,
from sound/core/memory.c:24:
include/asm/arch/memory.h: In function `__arch_adjust_zones':
include/asm/arch/memory.h:28: error: `PAGE_SHIFT' undeclared (first use
in this function)
This patch replaces my previous attempt at fixing this problem (Patch 3214/1) and is based on the following feedback:
Russell King wrote:
> The error you see came up on SA1100. The best solution was to move
> the __arch_adjust_zones() function out of line. I suggest ixp4xx
> does the same.
I have moved the function out of line into arch/arm/mach-ixp4xx/common-pci.c as suggested.
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Rod Whitby
This patch adds support for a new arm/ixp4xx machine - the Iomega NAS 100d network attached storage product. The NAS100D is a consumer device containing a 266MHz Intel IXP420 processor, 16MB of flash, 64MB of RAM, a 160Gb internal IDE hard disk, and 802.11b/g wireless on an Atheros mini-PCI card.
Work on porting the latest 2.6.x kernel to this device is being done by
the NSLU2-Linux project (the same team who maintains the port to the
Linksys NSLU2 device). In particular, the majority of this patch was
authored by Alessandro Zummo, based on the work done for MACH_NSLU2
support by the NSLU2-Linux core team of developers.
MACH_NAS100D (as implemented by this patch) can be enabled in jumbo
ixp4xx kernels without any affect on the other machines supported by
that kernel.
This patch applies cleanly against 2.6.15-rc7 and should be trivial to
apply to later kernel versions. It does not depend upon any other
patches.
Modified files (and number of lines inserted):
arch/arm/mach-ixp4xx/Kconfig | 8
arch/arm/mach-ixp4xx/Makefile | 1
include/asm-arm/arch-ixp4xx/hardware.h | 1
include/asm-arm/arch-ixp4xx/irqs.h | 9
include/asm-arm/arch-ixp4xx/nas100d.h | 75
arch/arm/mach-ixp4xx/nas100d-pci.c | 77
arch/arm/mach-ixp4xx/nas100d-power.c | 69
arch/arm/mach-ixp4xx/nas100d-setup.c | 133
-- Rod Whitby (NSLU2-Linux project lead)
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
Other than interrupt masking purposes, this API is only used when
configuring interrupt lines and this patch moves that functionality
directly into the ixp4xx_set_irq_type() implementation as board level
PCI code should not need to worry about those details.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since we now only build arch/arm/kernel/dma.c on machine types
which set ISA_DMA_API, we don't need to define MAX_DMA_CHANNELS
to 0 to indicate this - this definition becomes superfluous.
Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The old __address element in struct scatterlist remained from older
kernels because the ARM DMA emulation code made use of it. Move
this field into struct dma_struct, and convert DMA emulation code
to setup a SG entry as required.
Also, convert DMA emulation code to use the new DMA API rather
than the PCI DMA API.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow the compiler to optimise the bus_to_virt(virt_to_bus())
transformation in the ARM ISA DMA interface.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It seems that clk_use() and clk_unuse() are additional complexity
which isn't required anymore. Remove them from the clock framework
to avoid the additional confusion which they cause, and update all
ARM machine types except for OMAP.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It seems that there's some confusion over how the clock source
framework should be used. Add some additional comments to explain
the ambiguous areas.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/kernel/entry-armv.S has contained a comment suggesting
that asm/hardware.h and asm/arch/irqs.h should be moved into the
asm/arch/entry-macro.S include. So move the includes to these
two files as required.
Add missing includes (asm/hardware.h, asm/io.h) to asm/arch/system.h
includes which use those facilities, and remove asm/io.h from
kernel/process.c.
Remove other unnecessary includes from arch/arm/kernel, arch/arm/mm
and arch/arm/mach-footbridge.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Daniel Jacobowitz
Handle new EABI relocations when loading kernel modules. This is
necessary for CONFIG_AEABI kernels, and also for some broken
(since fixed) old ABI toolchains.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
This looks like a leftover from 2.4 days...
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Hiroki Kaminaga
This patch defines a new macro: pfn_to_kaddr(pfn).
Same macro is already defined on other arch, such as i386.
Signed-off-by: Hiroki Kaminaga <kaminaga@sm.sony.co.jp>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
Mark the ioremap'd cookie/pointer in said functions as const since
we should not be actualy touching the data. This fixes a slew of
compile warnings on IXP4xx as our reads[bwl] already mark this
parameter as const.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
sema_count() defined only for ARM but not used anywhere.
Signed-off-by: Arthur Othieno <a.othieno@bluewin.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARMv6K CPUs have SEV (send event) and WFE (wait for event) instructions
which allow the CPU clock to be suspended until another CPU issues a
SEV, rather than spinning on the lock wasting power. Make use of these
instructions.
Note that WFE does not wait if an event has been sent since the last WFE
cleared the event status, so although it may look racy, the instruction
implementation ensures that these are dealt with.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lucas Correia Villa Real
This patch adds definitions to GPIO registers for the S3C2400 into
include/asm-arm/arch-s3c2410/regs-gpio.h.
Signed-off-by: Lucas Correia Villa Real <lucasvr@gobolinux.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Unfortunately, we have a symbol clash between the SA-1100 header and
some drivers. Since everywhere which needs SA1100 specifics includes
asm/hardware.h, we don't need to include it in the SA1100 io.h header.
In file included from drivers/net/wireless/wavelan_cs.p.h:459,
from drivers/net/wireless/wavelan_cs.c:60:
drivers/net/wireless/wavelan_cs.h:97:1: warning: "LCSR" redefined
In file included from include/asm/arch/hardware.h:56,
from include/asm/hardware.h:16,
from include/asm/arch/io.h:13,
from include/asm/io.h:71,
from drivers/net/wireless/wavelan_cs.p.h:433,
from drivers/net/wireless/wavelan_cs.c:60:
include/asm/arch/SA-1100.h:1907:1: warning: this is the location of the previous definition
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Adam Brooks
Fixes an issue in 2.6.15-rc2 that prevented compilation of kernels for IOP3xx boards.
Signed-off-by: Adam Brooks <adam.j.brooks@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since the defintion of NODES_SHIFT may be overridden in asm/arch/memory.h
it's important to include asm/memory.h into asm/numnodes.h to ensure
that the correct value is always defined.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Kenneth Tan
To add queue manager region size which is missing from ixp4xx-regs.h
Signed-off-by: Kenneth Tan <chong.yin.tan@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The receiver status register reports latched error conditions, which
must be cleared by writing to it. However, the data register reports
unlatched conditions which are associated with the current character.
Use the data register to interpret error status rather than the RSR.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Unfortunately, later gcc versions error out when our get_user is passed
a const pointer, since we write to a temporary variable declared as
typeof(*(p)) which propagates the const-ness.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The "align" argument in ARMs __ioremap is unused and provides a
misleading expectation that it might do something. It doesn't.
Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In the old days when arm26/arm32 was combined into the same
architecture, proc-fns.h provided the xchg implementation for
arm26 CPUs. Since we no longer combine these two, this include
is no longer required. Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
