To clear the mask bit, setting data argument to be 0 with proper mask setting
for lp8788_update_bits. We don't need the var array here.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use of_match_ptr and add ifdef CONFIG_OF guard for regulator_gpio_of_match.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Don't adjust the selector in [get|set]_voltage_sel, fix it in list_voltage() instead.
For smps*(except smps10), the vsel reg-value and voltage mapping as below:
reg-value volt (uV) ( Assume RANGE is x1 )
0 0
1 500000
2 500000
3 500000
4 500000
5 500000
6 500000 (0.49V + 1 * 0.01V) * RANGE
7 510000 (0.49V + 2 * 0.01V) * RANGE
8 520000 (0.49V + 3 * 0.01V) * RANGE
9 530000 (0.49V + 4 * 0.01V) * RANGE
....
The linear mapping is start from selector 6.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Introduce a regulator_can_change_voltage() function for the subsytems or
drivers which might check if applying voltage change is possible and use
special workaround code when the driver is used with fixed regulators or
regulators with disabled ability to change the voltage.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If pdata->base_voltage_uV is missing or the settings of pdata->base_voltage_uV
and pdata->max_voltage_uV are out of range, TPS51632_VOLT_VSEL macro
returns wrong vsel.
Thus add checking [base|max]_voltage_uV pdata settings in probe.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use DIV_ROUND_UP to ensure selected voltage won't less than min_uV due to
integer truncation.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver can be converted to use linear_min_sel and
regulator_[map|list]_voltage_linear.
Below shows the equation (from Datasheet) for each LDOs.
For AUTOOUT:
VO(prog) = 0.625 + auto_out x 0.025 V; e.g.
(00000000 to 00101110: reserved)
00101111: 1.8 V (min)
01010011: 2.7 V
01101010: 3.275 V
01101011: 3.300 V
01101100: 3.325 V
01111111 : 3.800 V (max)
The linear mapping start from 0x2f selector.
Thus we convert this equation to:
VO(prog) = 1.8 + (selector - linear_min_sel) x 0.025 V
(min_uV = 1800000, uV_step = 25000, linear_min_sel = 0x2f)
For DOWNxOUT:
VO(prog) = 0.625 + downx_out x 0.025 V; e.g.
00000000 : 0.625 V (min)
00010111 : 1.200 V
00101111 : 1.800 V
01011111 : 3.000 V (max)
For xLDOOUT:
VO(prog) = 0.9 + xldo_out x 0.1 V; e.g.
00000: 0.9 V
00001: 1.0 V
11000 : 3.3 V
11011 : 3.6 V
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some Arizona devices such as the WM5102 can use DVFS on their digital core,
for these devices allow the voltage range to vary in the default setup.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Below equation means the "voltage" is the "smallest" voltage within specific
range.
ret = DIV_ROUND_UP(min - bottom) / step;
voltage = ret * step + bottom;
If we do try 1 down when (voltage > max), new voltage is then less than min
voltage. Which means the new voltage is not in the requested voltage range.
This patch also includes below cleanups:
- Use DIV_ROUND_UP
- rename variable 'ret' to 'sel' for better readability because as3711_sel_check
returns the selector.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Below cases are supposed to be valid:
min_uV == max_uV == info->max_uV
min_uV == max_uV == rdev->desc->min_uV
Don't return -EINVAL for above cases.
This patch also includes below cleanups:
- Use rdev_get_drvdata(rdev) instead of rdev->reg_data.
- Remove unnecessary WARN_ON, it looks pointless.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch fix the abnormal ramp delay setting.
The shift operation was wrong.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Checking da9052_current_limits[row][i] <= max_uA is not enough, it is possible
da9052_current_limits[row][i] may less than the requested min_uA.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Selecting the minimal value is only true for voltage regulators.
For current regulators the maximum in the given range should be
selected instead.
This issue was reported by Heiko Stuebner for gpio-regulator driver [1],
and the conclusion is to select the max current for current regulators [2].
[1] https://lkml.org/lkml/2012/8/5/162
[2] https://lkml.org/lkml/2012/8/6/183
This patch also ensures da9055_buck_set_current_limit return -EINVAL when the
supported current limit does not meet the request range.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When building the driver in debug mode, it generates
warning as
drivers/regulator/tps6586x-regulator.c: In function 'tps6586x_regulator_probe':
drivers/regulator/tps6586x-regulator.c:392:9: warning: 'id' is used uninitialized in this function [-Wuninitialized]
Fix this warning.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reported-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When tps->enable_pwm_dvfs is true, write to TPS51632_VOLTAGE_BASE_REG rather
than TPS51632_VOLTAGE_SELECT_REG.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some drivers (at least 3 drivers) have such variant of linear mapping that
the first few selectors are invalid and the reset are linear mapping.
Let's support this case in core.
This patch adds linear_min_sel in struct regulator_desc,
so we can allow specific minimal selector for starting linear mapping.
Then extends regulator_[map|list]_voltage_linear() to support this feature.
Note that for selectors less than min_linear_index, we need count them to
n_voltages so regulator_list_voltage() won't fail while checking the boundary
for selector before calling list_voltage callback.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add device tree based discovery support for max8997.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In case the gpio based volatage selection mode is not used for either of
buck 1/2/5, then only the BUCKxDVS1 register need to be programmed. So
determine whether dvs mode is used and limit the loop count appropriately.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The BUCKxDVSx register programming is now moved prior to setting up of the
gpio based dvs mode. This will ensure that all the BUCKxDVSx registers
are programmed with appropriate voltage values before the gpio based dvs
mode is selected for buck1/2/5.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver can be built as a module, add MODULE_ALIAS for it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If external control is enabled then do not provide regulator
enable/disable apis.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver supports the 4 DCDC and 8 LDO regulators on the AS3711 PMIC.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Implement list_voltage for fixed regulators, otherwise
regulator_is_supported_voltage() returns 0.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch includes below cleanups:
- Fix typo in comment
- Fix showing wrong register in dev_err
- Remove unnecessary rinfo variable
- Add TPS80032 to MODULE_DESCRIPTION
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch implements map_voltage and list_voltage callbacks to properly handle
the case voltage range that doesn't start with 0 offset.
Now we adjust the selector in map_voltage() before calling set_voltage_sel().
And return 0 in list_voltage() for invalid selectors.
With above change, we can remove da9055_regulator_set_voltage_bits function.
One tricky part is that we need adding voffset to n_voltages.
Although for the cases "selector < voffset" are invalid, we need add voffset to
n_voltage so regulator_list_voltage() won't fail while checking the boundary for
selector before calling list_voltage callback.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The MAXIM MAX8973 high-efficiency, three phase, DC-DC step-down
switching regulator delievers up to 9A of output current. Each
phase operates at a 2MHz fixed frequency with a 120 deg shift
from the adjacent phase, allowing the use of small magnetic
component.
Add regulator driver for this device.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Check pdata->gpio_rsel && pdata->gpio_rsel[id] for the case GPI pin is muxed
with regulator to select the regulator register set A/B for voltage ramping.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pefix "TPS80031" is added on all defines of tps80031 header
to avoid conflict with other header definitions.
Update the regualtor driver of tps80031 to use the same name.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is the Regulator patch for the DA9055 PMIC and has got dependency on
the DA9055 MFD core.
This patch support all of the DA9055 regulators. The output voltages are
fully programmable through I2C interface only. The platform data with regulation
constraints is passed down from the board to the regulator.
This patch is functionaly tested on SMDK6410 board. DA9055 Evaluation board
was connected to the SMDK6410 board.
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Moving regulator node parsing to regulator driver in place
of parsing it on mfd driver.
The motivation for this change are:
- MFD core driver should not depends on regulator and able
to instantiate device without regulator.
- The API for matching regulators are in regulator core and
it is good that regulator driver only calls this API.
- Regulator specific support should be in regulator driver only
to ease any enhancement/modification for regulators.
- The regulator driver is now registered as mfd sub device and
all regulator registration is done from single probe call.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
regulator_is_supported_voltage() should return true only if the voltage
of fixed/constant regulator is between min_uV and max_uV.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
A selection of voltage or current values (AKA states) should always
be specified when using a GPIO regulator. If there are no switchable
states then the fixed regulators should be used instead.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When regulator_register fails and exits through the scrub path the
regulator_put function was called whilst holding the
regulator_list_mutex, causing deadlock.
This patch adds a private version of the regulator_put function which
can be safely called whilst holding the mutex, replacing the
aforementioned call.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Need initilize of_node in regulator config when register regulator,
otherwise regulator driver think it is no-dt device.
in regulator_dev_lookup
list_for_each_entry(r, ®ulator_list, list)
if (r->dev.parent &&
node == r->dev.of_node)
return r
r->dev.of_noe will be zero if miss config in cfg.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add regulator driver for Texas Instrument TPS80031/TPS80032 device.
TPS80031/ TPS80032 Fully Integrated Power Management with Power
Path and Battery Charger. It has 5 configurable step-down
converters, 11 general purpose LDOs, VBUS generator and digital
output to control regulators.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the gpio_request_one() fails, or returns EPROBE_DEFER, the
regulator must be device_unregister()ed. When this is not done,
there are WARNING: from sysfs:
WARNING: at fs/sysfs/file.c:343 sysfs_open_file+0x238/0x268()
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch fixes a sparse warning. Since max77686_enable() is a callback,so it
should be static.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Here we provide the GPIO Regulator driver with Device Tree capability, so
that when a platform is booting with DT instead of platform data we can
still make full use of it.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The TPS65090's DCDC output can also be enable/disable through the
external digital input signal. Add support for enable/disable
either through register access via I2C or through external
control inputs. The external control inputs can be driven through
GPIOs also and hence adding support for passing the GPIO number.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
TPS65090 supports the two LDOs, LDO1 and LDO2. These are
always ON regulators. The output on these LDOs are available
once the input voltage available for these LDOs.
Add support for these LDOs regulators.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To make the names proper and more appropriate:
Rename the driver name from tps65090-regulator to tps65090-pmic.
Rename the regulators from TPS65090_ID_* to TPS65090_REGULATOR_*
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
MFD driver registers the regulator driver once per device and
hence it is require to register all regulators in single probe
call.
Following are details of changes done to achieve this:
- Move the regulator enums to mfd header and remove the
tps65090-regulator.h as it does not contain more info.
- Add max regulator and register all regulators even if there
is no regulator init data from platform.
- Convert regulator init data to pointer type in platform data.
- Add input supply name in regulator desc to provide input supply.
- Separate desc information from driver information.
- Disable external control bit to have control through register write.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix BUG_ON() error if tps65910 VRTC regulator is used with out
rdev->desc->volt_table data. Recent changes in regulator core driver
which add support for "regulator_list_voltage_table" have BUG_ON() if
regulator descriptor do not voltage table information. This patch adds
the voltage table information to fix the issue.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch implements set_suspend_disable callback for BUCKs which
support only switch ON/OFF modes during system suspend state, and
set_suspend_mode callbacks for LDOs which also suport Low power mode and
switch ON/OFF modes.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds basic support to take care of opmode(if any) which can be set by
set_suspend_[disable/mode] callbacks.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The of_device_id table is supposed to be zero-terminated.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Implementation of the regulator framework driver for the
Versatile Express voltage control. Devices without
voltage constraints (ie. "regulator-[min|max]-microvolt"
properties in the DT node) are treated as fixed (or rather
read-only) regulators.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some regulators can set any voltage within the constraints range,
not being limited to specified operating points.
This patch makes it possible to describe such regulator and makes
the regulator_is_supported_voltage() function behave correctly.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The TPS51632 is a driverless step down controller with
serial control. Advanced features such as D-Cap+
architecture with overlapping pulse support and OSR
overshoot reduction provide fast transient response,
lowest output capacitance and high efficiency.
The TPS51632 supports both I2C and DVFS interfaces
(through PWM) for dynamic control of the output voltage
and current monitor telemetry.
Add regulator driver for TPS51632.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As usual we have a few new drivers:
- TI LP8788
- TI OMAP USB TLL
- Maxim MAX8907
- SMSC ECE1099
- Dialog Semiconductor DA9055
- A simpler syscon driver that allow us to get rid of the anatop one.
Drivers are also gradually getting Device Tree and IRQ domain support.
The following drivers got DT support:
- palmas, 88pm860x, tc3589x and twl4030-audio
And those ones now use the IRQ domain APIs:
- 88pm860x, tc3589x, db8500_prcmu
Also some other interesting changes:
- Intel's ICH LPC now supports Lynx Point
- TI's twl4030-audio added a GPO child
- tps6527 enabled its backlight subdevice
- The twl6030 pwm driver moved to the new PWM subsystem
And finally a bunch of cleanup and casual fixes for mc13xxx, 88pm860x, palmas,
ab8500, wm8994, wm5110, max8907 and the tps65xxx family.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=n6lp
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD changes from Samuel Ortiz:
"MFD bits for the 3.7 merge window.
As usual we have a few new drivers:
- TI LP8788
- TI OMAP USB TLL
- Maxim MAX8907
- SMSC ECE1099
- Dialog Semiconductor DA9055
- A simpler syscon driver that allow us to get rid of the anatop one.
Drivers are also gradually getting Device Tree and IRQ domain support.
The following drivers got DT support:
- palmas, 88pm860x, tc3589x and twl4030-audio
And those ones now use the IRQ domain APIs:
- 88pm860x, tc3589x, db8500_prcmu
Also some other interesting changes:
- Intel's ICH LPC now supports Lynx Point
- TI's twl4030-audio added a GPO child
- tps6527 enabled its backlight subdevice
- The twl6030 pwm driver moved to the new PWM subsystem
And finally a bunch of cleanup and casual fixes for mc13xxx, 88pm860x,
palmas, ab8500, wm8994, wm5110, max8907 and the tps65xxx family."
Fix up various annoying conflicts: the DT and IRQ domain support came in
twice and was already in 3.6. And then it was apparently rebased.
Guys, DON'T REBASE!
* tag 'mfd-3.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (89 commits)
ARM: dts: Enable 88pm860x pmic
mfd: 88pm860x: Move gpadc init into touch
mfd: 88pm860x: Device tree support
mfd: 88pm860x: Use irqdomain
mfd: smsc: Add support for smsc gpio io/keypad driver
backlight: tps65217_bl: Add missing platform_set_drvdata in tps65217_bl_probe
mfd: DA9055 core driver
mfd: tps65910: Add alarm interrupt of TPS65910 RTC to mfd device list
mfd: wm5110: Add register patches for revision B
mfd: wm5110: Disable control interface error report for WM5110 rev B
mfd: max8907: Remove regulator-compatible from DT docs
backlight: Add TPS65217 WLED driver
mfd: Add backlight as subdevice to the tps65217
mfd: Provide the PRCMU with its own IRQ domain
mfd: Fix max8907 sparse warning
mfd: Add lp8788 mfd driver
mfd: dbx500: Provide a more accurate smp_twd clock
mfd: rc5t583: Fix warning messages
regulator: palmas: Add DT support
mfd: palmas: Change regulator defns to better suite DT
...
Pull workqueue changes from Tejun Heo:
"This is workqueue updates for v3.7-rc1. A lot of activities this
round including considerable API and behavior cleanups.
* delayed_work combines a timer and a work item. The handling of the
timer part has always been a bit clunky leading to confusing
cancelation API with weird corner-case behaviors. delayed_work is
updated to use new IRQ safe timer and cancelation now works as
expected.
* Another deficiency of delayed_work was lack of the counterpart of
mod_timer() which led to cancel+queue combinations or open-coded
timer+work usages. mod_delayed_work[_on]() are added.
These two delayed_work changes make delayed_work provide interface
and behave like timer which is executed with process context.
* A work item could be executed concurrently on multiple CPUs, which
is rather unintuitive and made flush_work() behavior confusing and
half-broken under certain circumstances. This problem doesn't
exist for non-reentrant workqueues. While non-reentrancy check
isn't free, the overhead is incurred only when a work item bounces
across different CPUs and even in simulated pathological scenario
the overhead isn't too high.
All workqueues are made non-reentrant. This removes the
distinction between flush_[delayed_]work() and
flush_[delayed_]_work_sync(). The former is now as strong as the
latter and the specified work item is guaranteed to have finished
execution of any previous queueing on return.
* In addition to the various bug fixes, Lai redid and simplified CPU
hotplug handling significantly.
* Joonsoo introduced system_highpri_wq and used it during CPU
hotplug.
There are two merge commits - one to pull in IRQ safe timer from
tip/timers/core and the other to pull in CPU hotplug fixes from
wq/for-3.6-fixes as Lai's hotplug restructuring depended on them."
Fixed a number of trivial conflicts, but the more interesting conflicts
were silent ones where the deprecated interfaces had been used by new
code in the merge window, and thus didn't cause any real data conflicts.
Tejun pointed out a few of them, I fixed a couple more.
* 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (46 commits)
workqueue: remove spurious WARN_ON_ONCE(in_irq()) from try_to_grab_pending()
workqueue: use cwq_set_max_active() helper for workqueue_set_max_active()
workqueue: introduce cwq_set_max_active() helper for thaw_workqueues()
workqueue: remove @delayed from cwq_dec_nr_in_flight()
workqueue: fix possible stall on try_to_grab_pending() of a delayed work item
workqueue: use hotcpu_notifier() for workqueue_cpu_down_callback()
workqueue: use __cpuinit instead of __devinit for cpu callbacks
workqueue: rename manager_mutex to assoc_mutex
workqueue: WORKER_REBIND is no longer necessary for idle rebinding
workqueue: WORKER_REBIND is no longer necessary for busy rebinding
workqueue: reimplement idle worker rebinding
workqueue: deprecate __cancel_delayed_work()
workqueue: reimplement cancel_delayed_work() using try_to_grab_pending()
workqueue: use mod_delayed_work() instead of __cancel + queue
workqueue: use irqsafe timer for delayed_work
workqueue: clean up delayed_work initializers and add missing one
workqueue: make deferrable delayed_work initializer names consistent
workqueue: cosmetic whitespace updates for macro definitions
workqueue: deprecate system_nrt[_freezable]_wq
workqueue: deprecate flush[_delayed]_work_sync()
...
When the bindings for the TPS6586x regulator were being proposed, I
asserted that DT node naming rules for bus child nodes should also be
applied to nodes inside the TPS6586x regulator node itself. In other
words, that each node providing regulator init data should be named
after the type of object it represented ("regulator") and hence that
some other property was required to indicate which regulator the node
described ("regulator-compatible"). In turn this led to multiple nodes
having the same name, thus requiring node names to use a unit address
to make them unique, thus requiring reg properties within the nodes and
However, subsequent discussion indicates that the rules I was asserting
only applies to standardized bus nodes, and within a device's own node,
the binding can basically do anything sane that it wants.
Hence, this change deprecates the register-compatible property, and
instead uses node names to replace this functionality. This greatly
simplifies the device tree content, making them smaller and more legible.
The code is changed such that old device trees continue to work.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add DT support to palmas regulator. This involved a little change to
the platform data structure. Regulator information can now come from
platform data or DT.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since PREG regulator is the only one regulator in 88PM8606, and other
regulators are in 88PM8607. Checking resource as identifying regulator
is not a good way. We can use NULL resource to indentify PREG regulator.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Pre-regulator of 88pm8606 is mainly for support charging based on vbus,
it needs to be enabled for charging battery, and will be disabled in
some exception condition like over-temp.
Add the pre-regulator support for 88pm860x regulator driver.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Remove array in parent's platform data. Use struct regulator_init_data
as regulator device's platform data directly. So a lot of pdata are
added into parent's platform data. And voltage out register offset
is used as IORESOURCE_REG to distinguish different regualtor devices.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Using syscon to access anatop register.
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
- A tps65217 build error fix.
- A lcp_ich regression fix caused by the MFD driver failing to initialize the
watchdog sub device due to ACPI conflicts.
- 2 MAX77693 interrupt handling bug fixes.
- An MFD core fix, adding an IRQ domain argument to the MFD device addition
API in order to prevent silent and potentially harmful remapping behaviour
changes for drivers supporting non-DT platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJQVQpwAAoJEIqAPN1PVmxKpnQP/iDPakfGT0m00nxk9VvuXfaA
SlNxhhM1ZPxlZcBrVFULZ+dCVuUaBYIfwoT4Wwl2yZsmp8uYb62Rd6LGXDnjO+FH
zKMg3b/KDHq/jicYxqFy4bVq3I850jTLN4Hti6hArn8HM6gxZJQxM810Poxt6M0T
odud6oHSevGpCoL7GU4O+gmx1wKSDRrw6TZPokJDfXaQcFPJEt0YGGtI2zAO1sV+
iBPQE/bI3bF5r/kowbh9ro5WybGNyFrwiYtaTzJWntXoPKN1lmr0F2F2NaCEo1xj
2vJPFSCK3qC9Ft7sPQEBYxrSXzyzgu7G8HGgkcBG5SaSo+W3awe9DEaHfk5E7sdr
iyc01kh4FmGlMAvHG/zcK3YvchR7GJdRI7BrR+MTQ03ZUv/ZrmTYFAHv5fAzBQ+N
6ZUoC/1bqPKpfeFPOKYpDeYJVnFBWLYr+t7McTqqg+kpxUuYnQ0HyJVjDh01ZVQT
AtCjjW7R+Ka44B+xfMOartPZMqZZEHSJ0UjacyEyzMpAAY14eUDMtTqs/jtNp+8Z
B0bZiA8ZhUmNVH7TZoT/u57FgEW34JnM8oH6jLVN+yjInpuugIvqpZn0TA90GL7V
Fh2DALMgUN5z/TXduGSsSPg1hvXFPOujaS+4o78e8PWiVQd5XUk/mc8OOS/mrRwj
+mILnzxJcp8iYrYqESbt
=nP/y
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-3.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull mfd fixes from Samuel Ortiz:
"This is the remaining MFD fixes for 3.6, with 5 pending fixes:
- A tps65217 build error fix.
- A lcp_ich regression fix caused by the MFD driver failing to
initialize the watchdog sub device due to ACPI conflicts.
- 2 MAX77693 interrupt handling bug fixes.
- An MFD core fix, adding an IRQ domain argument to the MFD device
addition API in order to prevent silent and potentially harmful
remapping behaviour changes for drivers supporting non-DT
platforms."
* tag 'mfd-for-linus-3.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: MAX77693: Fix NULL pointer error when initializing irqs
mfd: MAX77693: Fix interrupt handling bug
mfd: core: Push irqdomain mapping out into devices
mfd: lpc_ich: Fix a 3.5 kernel regression for iTCO_wdt driver
mfd: Move tps65217 regulator plat data handling to regulator
The U8500 has its own set of separate header, so the abx500
becomes completely abstract. Do the same split for the AB3100
legacy ASIC.
Signed-off-by: Marcus Cooper <marcus.xm.cooper@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since IORESOURCE_IO is changed to IORESOURCE_REG in 88pm860x driver,
update self-defined IORESOURCE_IO resource to register offset that
is IORESOURCE_REG in regulator driver. And split regulator platform
data array into scattered platform data.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This was originally written by Russell King who unfortunately found
himself unable to take the patch futher.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Tested-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The max voltage will be bounded by min_uV, uV_step and n_voltages, so
remove it to avoid confusing.
Signed-off-by: Yunfan Zhang <yfzhang@marvell.com>
Reviewed-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Doing so generates a warning as the first field is a pointer but we use
0 to initalize it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Many regulators support a bypass mode where they simply switch their
input supply to the output. This is mainly used in low power retention
states where power consumption is extremely low so higher voltage or
less clean supplies can be used.
Support this by providing ops for the drivers and a consumer API which
allows the device to be put into bypass mode if all consumers enable it
and the machine enables permission for this.
This is not supported as a mode since the existing modes are rarely used
due to fuzzy definition and mostly redundant with modern hardware which is
able to respond promptly to load changes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Graeme Gregory <gg@slimlogic.co.uk>
This driver supports Fairchild FAN53555 Digitally Programmable
TinyBuck Regulator. The FAN53555 is a step-down switching voltage
regulator that delivers a digitally programmable output from an
input voltage supply of 2.5V to 5.5V. The output voltage is
programmed through an I2C interface.
Signed-off-by: Yunfan Zhang <yfzhang@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the device doesn't have a regmap specified by the driver and we can't
find one on the device itself try its parent, providing a useful defualt
for many MFDs.
[Rewrite commit message -- broonie]
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Users (especially framework code) may end up passing in a zero deferral
time depending on runtime conditions or configuration. If they do then
just call regulator_disable() directly to save scheduling.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
If a regulator only supports a single voltage list_voltage() can be used
to report what that voltage is so add this as one of the criteria for
creating the microvolts file in sysfs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Device have SYS rail which is always ON. It is system power bus. LDO5
and LDO_RTC get powered through this rail internally. Add support for
this rail and make the LDO5/LDO_RTC supply by it. Update document
accordingly.
[swarren: Instantiate the sys regulator from board-harmony-power.c to
avoid regression.]
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The lp872x_check_dvs_validity() is used for checking DVS platform data.
If the DVS platform data is not defined, return as error code.
Now, this is unnecessary because the default DVS mode is set in this case.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The lp872x_set_dvs() is used for changing the DVS pin state.
This function works only when the DVS platform data is defined.
So don't assume that DVS data is always valid.
In case the platform data is not defined, the DVS data is set to NULL
for skipping the DVS pin control.
DVS selection and GPIO pin number are used for the LP872x DVS pin control.
For better readability, DVS selection argument is added in lp872x_set_dvs().
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The platform specific configuration(general_config) is optional.
However, the DVS settings should be configured explicitly while
loading the driver.
This patch enables configuring the default DVS mode even though
the platform data is not defined.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The lp872x driver has the DVS platform data which select the register address
of the BUCK voltage.
This patch enables updating the default DVS mode when the DVS platform data
is not defined.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch enables registering the regulator driver even though
the regulator_init_data is not defined in the platform side.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver can be built as a module, add MODULE_ALIAS for it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If a regulator is not used by a board, it's quite legitimate not to
provide platform data or a device tree node to configure it (i.e.
regulator_init_data). In that case, during MAX8907 regulator's
probe(), the idata variable will be NULL for that regulator. Prevent
dereferincing it.
If the MBATT regulator's init_data is not specified, or no name was
specified in the constraints, the regulator will be named based on
the regulator descriptor, so initialize mbatt_rail_name from there.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix regulator kernel-doc warnings:
Warning(drivers/regulator/core.c:2308): No description found for parameter 'rdev'
Warning(drivers/regulator/core.c:2308): Excess function parameter 'regulator' description in 'regulator_set_voltage_time_sel'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This encodes the voltage shifts (the number of bits to shift
the register to get to the selector) into the regulator info.
We have several new variants of the AB8500 so this varies a
lot.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix the following:
CC [M] drivers/regulator/max8907-regulator.o
drivers/regulator/max8907-regulator.c: In function 'max8907_regulator_probe':
drivers/regulator/max8907-regulator.c:297:12: error: 'max8907_matches' undeclared (first use in this function)
by removing direct references to max8907_matches[], which only exists when
CONFIG_OF is defined.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add missing platform_get_drvdata() call in max8907_regulator_remove(), this
fixes below build warning:
CC [M] drivers/regulator/max8907-regulator.o
drivers/regulator/max8907-regulator.c: In function 'max8907_regulator_remove':
drivers/regulator/max8907-regulator.c:353:23: warning: 'pmic' is used uninitialized in this function [-Wuninitialized]
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For linear voltage mapping, the n_voltages is (max - min) / step + 1
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fixes this build error:
drivers/regulator/twl-regulator.c: In function 'twlreg_probe':
drivers/regulator/twl-regulator.c:1229:3: error: implicit declaration of function 'kfree' [-Werror=implicit-function-declaration]
Also added string.h for kmemdup().
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The MAX8907 is an I2C-based power-management IC containing voltage
regulators, a reset controller, a real-time clock, and a touch-screen
controller.
The original driver was written by:
* Gyungoh Yoo <jack.yoo@maxim-ic.com>
Various fixes and enhancements by:
* Jin Park <jinyoungp@nvidia.com>
* Tom Cherry <tcherry@nvidia.com>
* Prashant Gaikwad <pgaikwad@nvidia.com>
* Dan Willemsen <dwillemsen@nvidia.com>
* Laxman Dewangan <ldewangan@nvidia.com>
During upstreaming, I (swarren):
* Converted to regmap.
* Allowed probing from device tree.
* Reworked the regulator driver to be represented as a single device that
provides multiple regulators, rather than as a device per regulator.
* Replaced many regulator ops with standard functions.
* Added ability to specify supplies for each regulator.
* Removed the WLED regulator. If/when we expose this in the driver, it
should be a backlight object not a regulator object.
* Renamed from max8907c->max8907, since the driver covers at least the
C and B revisions.
* General cleanup.
Signed-off-by: Gyungoh Yoo <jack.yoo@maxim-ic.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
I currently carry the series to make of_device_id->data const in the
arm-soc tree, which fixes a number of issues, but leaves one new
compiler warning about the twl-regulator driver:
drivers/regulator/twl-regulator.c: In function 'twlreg_probe':
drivers/regulator/twl-regulator.c:1130:8: warning: assignment discards 'const'
qualifier from pointer target type [enabled by default]
drivers/regulator/twl-regulator.c:1139:9: warning: assignment discards 'const'
qualifier from pointer target type [enabled by default]
The warning indicates that the driver takes a static table with
initialization data for each regulator, modifies the data in place
and passes a pointer to that structure to the regulator_register
function. This is probably ok because a system contains only one
instance of each regulator, but it's still bad style because any
driver should be written to support multiple instances of the same
hardware.
This patch changes the code to dynamically allocate the memory
we pass to the regulator core so the table can be constant.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is not required after commit f7df20ec
"regulator: core: Use list_voltage() to read single voltage regulators"
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is not required after commit f7df20ec
"regulator: core: Use list_voltage() to read single voltage regulators"
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is not required after commit f7df20ec
"regulator: core: Use list_voltage() to read single voltage regulators"
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is not required after commit f7df20ec
"regulator: core: Use list_voltage() to read single voltage regulators"
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is not required after commit f7df20ec
"regulator: core: Use list_voltage() to read single voltage regulators"
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
MAX77686_REGULATORS is known in compile time.
Use array to save pointer to rdev makes the code simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Initialize config.of_node for regulator before registering.
This is needed for DT based regulator support.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To set REGULATOR_MODE_IDLE mode, what we do is to clear DC1_ACTIVE and
DC1_SLEEP bits, this can be done in one wm8400_set_bits() call.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
wm831x_reg_read() returns negative error code on failure.
This prevents using the error code as the value read.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We already know the mask in lp8788_init_dvs() function, and we can update
the corresponding bit for default_dvs_mode in lp8788_init_dvs() function.
This function looks not necessary to me.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Tested-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For fixed voltage, the n_voltages should be 1 rather than 0.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use mc13xxx_reg_rmw rather than a mc13xxx_reg_read and a mc13xxx_reg_write calls.
This logic to set MC13892_SWITCHERS0_SWxHI bit is pretty simple:
if (volt > 1375000)
set MC13892_SWITCHERS0_SWxHI bit
else if (volt < 1100000)
clear MC13892_SWITCHERS0_SWxHI bit
else
leave MC13892_SWITCHERS0_SWxHI bit untouched
We already know the selector, so we don't need to calculate the selector again.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Then we can remove lock/unlock around the caller.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Then we can remove lock/unlock around the caller.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The voltage selection logic is supposed to find the samllest voltage falls
within specified range. When using equation to calculate vsel, we need to
ensure the requested min_uV meet the range of using the equation.
Otherwise we may select a voltage that is out of specified range.
For example, in the case vsel = 62 means select voltage of 2100000uV.
What we want is to ensure the requested min_uV <= 2100000 rather than checking
max_uV >= 2100000. And this also means in the case min_uV > 2100000, vsel = 62
does not meet the request.
Also calling twl6030smps_list_voltage() for all cases to ensure the selected
voltage still in bounds.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This was missing until now and the underlying
_regulator_do_set_voltage is using this value when calling list_voltage.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The number of regulator is known at compile time, use array to save pointer to
rdev makes the code simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Regulator platform data handling was mistakenly added to MFD
driver. So we will see build errors if we compile MFD drivers
without CONFIG_REGULATOR. This patch moves regulator platform
data handling from TPS65217 MFD driver to regulator driver.
This makes MFD driver independent of REGULATOR framework so
build error is fixed if CONFIG_REGULATOR is not set.
drivers/built-in.o: In function `tps65217_probe':
tps65217.c:(.devinit.text+0x13e37): undefined reference
to `of_regulator_match'
This patch also fix allocation size of tps65217 platform data.
Current implementation allocates a struct tps65217_board for each
regulator specified in the device tree. But the structure itself
provides array of regulators so one instance of it is sufficient.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Regulator platform data handling was mistakenly added to MFD
driver. So we will see build errors if we compile MFD drivers
without CONFIG_REGULATOR. This patch moves regulator platform
data handling from TPS65217 MFD driver to regulator driver.
This makes MFD driver independent of REGULATOR framework so
build error is fixed if CONFIG_REGULATOR is not set.
drivers/built-in.o: In function `tps65217_probe':
tps65217.c:(.devinit.text+0x13e37): undefined reference
to `of_regulator_match'
This patch also fix allocation size of tps65217 platform data.
Current implementation allocates a struct tps65217_board for each
regulator specified in the device tree. But the structure itself
provides array of regulators so one instance of it is sufficient.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
flush[_delayed]_work_sync() are now spurious. Mark them deprecated
and convert all users to flush[_delayed]_work().
If you're cc'd and wondering what's going on: Now all workqueues are
non-reentrant and the regular flushes guarantee that the work item is
not pending or running on any CPU on return, so there's no reason to
use the sync flushes at all and they're going away.
This patch doesn't make any functional difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Mattia Dongili <malattia@linux.it>
Cc: Kent Yoder <key@linux.vnet.ibm.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Bryan Wu <bryan.wu@canonical.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Petr Vandrovec <petr@vandrovec.name>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Avi Kivity <avi@redhat.com>
Fix regulator kernel-doc warnings:
Warning(drivers/regulator/core.c:2308): No description found for parameter 'rdev'
Warning(drivers/regulator/core.c:2308): Excess function parameter 'regulator' description in 'regulator_set_voltage_time_sel'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It seems commit 2098e95ce9 (regulator: twl:
adapt twl-regulator driver to dt) accidentally deleted VINTANA1. Also
the same commit defines VINTANA2 twice with TWL4030_ADJUSTABLE_LDO and
TWL4030_FIXED_LDO. This patch changes the fixed one to be VINTANA1.
I noticed this when auditing my N900 boot logs. I could not notice any
change in device behaviour, though, except that the boot logs are now
like before:
...
[ 0.282928] VDAC: 1800 mV normal standby
[ 0.284027] VCSI: 1800 mV normal standby
[ 0.285400] VINTANA1: 1500 mV normal standby
[ 0.286865] VINTANA2: 2750 mV normal standby
[ 0.288208] VINTDIG: 1500 mV normal standby
[ 0.289978] VSDI_CSI: 1800 mV normal standby
...
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Commit 65f735082d ("regulator: core: Add core support for GPIO controlled
enable lines") introduced enable gpio entry in regulator configuration
structure. Some drivers use '-1' as a placeholder for marking that such
gpio line is not available, because '0' is considered as a valid gpio
number. This patch fixes initialization of such drivers (like MAX8952
on UniversalC210 board), when '-1' is provided as enable gpio pin in the
regulator's platform data.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the regulator doesn't supply a way of reading back the voltage but does
provide a list_voltage() operation then use that with a selector of zero
to read the voltage. Regulators doing this means that we have the list
operation there for consumers that want to configure themselves.
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This prevents the output of just
dummy:
in the boot log. Now it says:
regulator-dummy: no parameters
which at least doesn't make it look like an accidental printk and also doesn't
only use "dummy" which could mean anything.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Originally gpio-regulator used the first item of its state list
that matched the given voltage or current range.
Commit 4dbd8f63f0 (regulator: gpio-regulator: Set the smallest voltage/current
in the specified range) changed this, to make the selection independent of
the ordering of the state list.
But selecting the minimal value is only true for voltage regulators.
For current regulators the maximum in the given range should be
selected instead.
Therefore split the previous common selection function into specific
functions for voltage and current regulators.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The conversion to voltage tables in
commit a3beb74261
"regulator: ab3100: Use regulator_list_voltage_table()"
missed to add the voltage table to the buck. Fix this and
it works like a charm.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The mask used in anatop_get_voltage_sel does not match the mask used in
anatop_set_voltage_sel.
We need to do left shift anatop_reg->vol_bit_shift bits for the correct mask.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As per datasheet, the vin pin for the regulator is named
as vin_sm0, vin_sm1, vin_sm2 for sm0, sm1 and sm2 respectively.
Correcting the names in driver and documentation to match with
datasheet.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reported-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix below error handling cases:
1. If reading PALMAS_SMPS_CTRL fails, simply returns ret rather than goto
err_unregister_regulator because we have not call regulator_register().
2. If palmas_ldo_init() fails, we need to call regulator_unregister() for the
regulator we just successfully registered in this for loop iteration.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current code uses wrong calls palmas_smps_[read|write] in palmas_ldo_init(),
should be palmas_ldo_[read|write] instead.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch fixes below issues when choosing selector:
1. Current code returns negative selector if min_uV < 900000 which is wrong.
For example, it is possible to satisfy the request with selector = 1 if
the requested min_uV is 850000.
2. Current code may select a voltage lower than requested min_uV.
For example, if the requested min_uV is 945000, current code chooses
selector = 1 which is lower than requested min_uV.
DIV_ROUND_UP to avoid this case.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is to address the following warning during compilation time: (Compile on x86_64)
CC drivers/regulator/core.o
drivers/regulator/core.c: In function '_regulator_do_set_voltage':
drivers/regulator/core.c:2183:10: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
This patch adds a temporary variable to avoid double cast.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When registering the regulator and setting supply for the regulator
then increment open_count to reflect correct number of users.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Too many thens in the if...then clause.
Reported-by: Michael Jones <michael.jones@matrix-vision.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Due to a merge conflict we are getting this:
drivers/regulator/s5m8767.c: In function ‘s5m8767_pmic_probe’:
drivers/regulator/s5m8767.c:575:2: error: implicit declaration of function
‘s5m_reg_write’ [-Werror=implicit-function-declaration]
This is fixed by fully converting this driver to the new s5m API.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We have support for a few new drivers:
- Samsung s2mps11
- Wolfson Microelectronics wm5102 and wm5110
- Marvell 88PM800 and 88PM805
- TI twl6041
We also have our regular driver improvements:
- Device tree and IRQ domain support for STE AB8500
- Regmap and devm_* API conversion for TI tps6586x
- Device tree support for Samsung max77686
- devm_* API conversion for STE AB3100
Besides that, quite a lot of fixing and cleanup for mc13xxx, tps65910,
tps65090, da9052 and twl-core.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=c28c
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD bits from Samuel Ortiz:
"We have support for a few new drivers:
- Samsung s2mps11
- Wolfson Microelectronics wm5102 and wm5110
- Marvell 88PM800 and 88PM805
- TI twl6041
We also have our regular driver improvements:
- Device tree and IRQ domain support for STE AB8500
- Regmap and devm_* API conversion for TI tps6586x
- Device tree support for Samsung max77686
- devm_* API conversion for STE AB3100
Besides that, quite a lot of fixing and cleanup for mc13xxx, tps65910,
tps65090, da9052 and twl-core."
Fix up mostly trivial conflicts, with the exception of
drivers/usb/host/ehci-omap.c in particular, which had some
re-organization of the reset sequence (commit 1a49e2ac96: "EHCI:
centralize controller initialization") that clashed with commit
2761a63945 ("mfd: USB: Fix the omap-usb EHCI ULPI PHY reset fix
issues").
In particular, commit 2761a63945 moved the usb_add_hcd() to the
*middle* of the reset sequence, which clashes fairly badly with the
reset sequence re-organization (although it could have been done inside
the new omap_ehci_init() function).
I left that part of commit 2761a63945 just undone.
* tag 'mfd-3.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (110 commits)
mfd: Ensure AB8500 platform data is passed through db8500-prcmu to MFD Core
mfd: Arizone core should select MFD_CORE
mfd: Fix arizona-irq.c build by selecting REGMAP_IRQ
mfd: Add debug trace on entering and leaving arizone runtime suspend
mfd: Correct tps65090 cell names
mfd: Remove gpio support from tps6586x core driver
ARM: tegra: defconfig: Enable tps6586x gpio
gpio: tps6586x: Add gpio support through platform driver
mfd: Cache tps6586x register through regmap
mfd: Use regmap for tps6586x register access.
mfd: Use devm managed resources for tps6586x
input: Add onkey support for 88PM80X PMIC
mfd: Add support for twl6041
mfd: Fix twl6040 revision information
mfd: Matches should be NULL when populate anatop child devices
input: ab8500-ponkey: Create AB8500 domain IRQ mapping
mfd: Add missing out of memory check for pcf50633
Documentation: Describe the AB8500 Device Tree bindings
mfd: Add tps65910 32-kHz-crystal-input init
mfd: Drop modifying mc13xxx driver's id_table in probe
...
The most important feature of this patch set is the new async infrastructure
that makes sure async_synchronize_full() synchronizes all domains and allows
us to remove all the hacks (like having scsi_complete_async_scans() in the
device base code) and means that the async infrastructure will "just work" in
future. The rest is assorted driver updates (aacraid, bnx2fc, virto-scsi,
megaraid, bfa, lpfc, qla2xxx, qla4xxx) plus a lot of infrastructure work in
sas and FC.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQDjDCAAoJEDeqqVYsXL0M/sMH/jVgBfF1mjR+DQuTscKyD21w
0BQLn5OmvDZDqo44iqQzNRObw7CxkBkUtHoozsknLijw+KggER653ZOAtUdIHfI/
/uo7iJQ3J3D/Ezm99HYSpZiF2juZwsBRtFBoKkGqOpMlzFUx5o4hUbH5OcINxnHR
VmvJU5K1kg8D77Q6zK+Atl14/Rfibc2IoufFmbYdplUAM/tV0BpBSSHJAJvqua76
NGMl4KJcPZnXe/4LXcxZia5A2efdFFEzaQ2mM9rUVEAgHDAxc0Zg9IoDhGd08FX4
G55NK+6+bKb9s7bgyva0T/iy817TRCzjteeYNFrb8nBRe7aQbAivaBHQFXIyvdQ=
=y2sh
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"The most important feature of this patch set is the new async
infrastructure that makes sure async_synchronize_full() synchronizes
all domains and allows us to remove all the hacks (like having
scsi_complete_async_scans() in the device base code) and means that
the async infrastructure will "just work" in future.
The rest is assorted driver updates (aacraid, bnx2fc, virto-scsi,
megaraid, bfa, lpfc, qla2xxx, qla4xxx) plus a lot of infrastructure
work in sas and FC.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (97 commits)
[SCSI] Revert "[SCSI] fix async probe regression"
[SCSI] cleanup usages of scsi_complete_async_scans
[SCSI] queue async scan work to an async_schedule domain
[SCSI] async: make async_synchronize_full() flush all work regardless of domain
[SCSI] async: introduce 'async_domain' type
[SCSI] bfa: Fix to set correct return error codes and misc cleanup.
[SCSI] aacraid: Series 7 Async. (performance) mode support
[SCSI] aha152x: Allow use on 64bit systems
[SCSI] virtio-scsi: Add vdrv->scan for post VIRTIO_CONFIG_S_DRIVER_OK LUN scanning
[SCSI] bfa: squelch lockdep complaint with a spin_lock_init
[SCSI] qla2xxx: remove unnecessary reads of PCI_CAP_ID_EXP
[SCSI] qla4xxx: remove unnecessary read of PCI_CAP_ID_EXP
[SCSI] ufs: fix incorrect return value about SUCCESS and FAILED
[SCSI] ufs: reverse the ufshcd_is_device_present logic
[SCSI] ufs: use module_pci_driver
[SCSI] usb-storage: update usb devices for write cache quirk in quirk list.
[SCSI] usb-storage: add support for write cache quirk
[SCSI] set to WCE if usb cache quirk is present.
[SCSI] virtio-scsi: hotplug support for virtio-scsi
[SCSI] virtio-scsi: split scatterlist per target
...
TI LP8788 PMU has 4 BUCKS and 22 LDOs.
The voltage of BUCK1 and BUCK2 can be controlled by external gpios.
And some LDOs also can be enabled by external gpios.
The regmap interface is used for regulator operations.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This function does not exist, remove the extern function declaration.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is in preparation for teaching async_synchronize_full() to sync all
pending async work, and not just on the async_running domain. This
conversion is functionally equivalent, just embedding the existing list
in a new async_domain type.
The .registered attribute is used in a later patch to distinguish
between domains that want to be flushed by async_synchronize_full()
versus those that only expect async_synchronize_{full|cookie}_domain to
be used for flushing.
[jejb: add async.h to scsi_priv.h for struct async_domain]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Set the supply_name in the regulator descriptor unconditionally
and make this parameter as required parameter in the device
node for successfully registration of the regulator.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The logic of calculating selector in palmas_map_voltage_smps() does not match
the logic to list voltage in palmas_list_voltage_smps().
We use below equation to calculate voltage when selector > 0:
voltage = (0.49V + (selector * 0.01V)) * RANGE
RANGE is either x1 or x2
So we need to take into account with the multiplier set in VSEL register when
calculating selector in palmas_map_voltage_smps()
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pass regulator id rahter than the index to lp872x_find_regulator_init_data(),
then the code can be simpler.
We can also get max_regulators by lp->num_regulators.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Tested-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to the datasheet, the voltage for twl6030ldo_ops is not linear for
all cases. Linear mapping is only for the selection code from
00000001 to 00011000.
Table 9. LDO Output Voltage Selection Code
CODE VOUT(V) COD VOUT(V) CODE VOUT(V) CODE VOUT(V)
00000000 0 00001000 1.7 00010000 2.5 00011000 3.3
00000001 1.0 00001001 1.8 00010001 2.6 00011001 Reserved
00000010 1.1 00001010 1.9 00010010 2.7 00011010 Reserved
00000011 1.2 00001011 2.0 00010011 2.8 00011011 Reserved
00000100 1.3 00001100 2.1 00010100 2.9 00011100 Reserved
00000101 1.4 00001101 2.2 00010101 3.0 00011101 Reserved
00000110 1.5 00001110 2.3 00010110 3.1 00011110 Reserved
00000111 1.6 00001111 2.4 00010111 3.2 00011111 2.75
This patch implements the list_voltage callback based on above table.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As Prefix of Samsung pmic changed from s5m to s2m,
To make common mfd driver for s2m and s5m series,
This patch rename header of Samsung mfd and modify mfd driver.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Previous naming rule of samsung pmic start with s5m prefix.
But It is changed by s2m.
To cover various samsung s2m and s5m series,
This patch modify function and variable name for common usage.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Previously, Samsung PMIC naming rule start with prefix of s5m.
But Naming rule is changed.
From now on, Prefix will be changed to s2m.
So, To support pmic series of s5m and s2m, change mfd file and directory name.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In twl6030ldo_set_voltage, current code use below formula to calculate vsel:
vsel = (min_uV/1000 - 1000)/100 + 1;
This is worng because when min_uV is 1000000 uV, vsel is 1.
It should be 0 in this case.
Fix it by change the equation to: (This equation is common for linear mapping)
vsel = DIV_ROUND_UP(min_uV - rdev->desc->min_uV, rdev->desc->uV_step);
In twl6030ldo_get_voltage, current code use below formula to calculate voltage:
mV = 1000mv + 100mv * (vsel - 1)
This is worng because when vsel is 0, mV is 900mV. Note the min_uV is 1000mV.
Fix it by change the equation to: (This equation is common for linear mapping)
return rdev->desc->min_uV + vsel * rdev->desc->uV_step;
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert to devm_gpio_request to save a few error handling code.
This patch properly handle the gpio_request failure, we should return error
when gpio_request fails rather than just show warning.
I think one of the reason we got -EBUSY is because current code does not free
gpios in s5m8767_pmic_remove(). So it got -EBUSY when reload the module.
Yest another reason is in current code if gpio_request() returns error,
the rest of the code still calls gpio_direction_output to config buck_gpios
and buck_ds gpios. This looks wrong to me.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert to devm_gpio_request to save a few error handling code.
This patch properly handle the gpio_request failure with -EBUSY, we should
return error rather than ommit the gpio_request failure with -EBUSY.
I think one of the reason we got -EBUSY is because current code does not free
gpios in max8997_pmic_remove(). So it got -EBUSY when reload the module.
Yest another reason is in current code if gpio_request() returns -EBUSY,
the rest of the code still calls gpio_direction_output to config buck125_gpios
and set gpio value in max8997_set_gpio(). This looks wrong to me.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use devm_ version of gpio APIs gpio_request_one() for
requesting gpios.
This avoid extra code for freeing gpios.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is multiple voltage input pins on device which
takes the voltage input for different voltage regulator.
Support to configure the voltage input supplied by
different regulator for each regulators.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This commit adds device tree support for tps65217 pmic. And usage
details are added to device tree documentation. Driver is tested
by using kernel module with regulator set and get APIs.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Both min_uV and max_uV are not used in the code, remove them.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Initialize config.of_node for regulator before registering.
This is needed for DT based regulator support.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
REGULATOR_STATUS_UNDEFINED is to be returned by regulator, if any other state
doesn't really apply.
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Case REGULATOR_STATUS_STANDBY -> REGULATOR_MODE_STANDBY.
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently s2mps11->iodev, s2mps11->dev and config.dev point to NULL.
This patch fixes the settings for config.dev.
Current code does not need the *dev and *iodev of struct s2mps11_info,
so remove them.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The tps65910 mfd driver has been converted to regmap APIs.
This patch adds tps65910_reg_update_bits() in include/linux/mfd/tps65910.h.
Thus we can use tps65910_reg_read/tps65910_reg_write/tps65910_reg_update_bits
directly and remove tps65910_reg_[read|modify_bits|read_locked|write_locked]
functions. With this change, we can also remove the mutex in struct tps65910_reg.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Tested-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
