Since cfg80211 will now call the explicit stop_ap
operation when an AP interface goes down, move all
teardown code there and remove it from interface
handling. The only thing that needs to stay is the
code to dev_close() all dependent VLANs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For a local variable there's no need to use the atomic
set_bit() operation, use __set_bit() instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove a duplicate check in ieee80211_rx_mgmt_beacon,
there is no need to make again the same check for the
IEEE80211_HW_PS_NULLFUNC_STACK twice; the two ifs can
be consolidated.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
[reword commit message & break long lines and also
clean up variable]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These were missed due to the tracing work having
started on a kernel that didn't have P2P Device
yet, implement them now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Expose a function for the AES-CMAC subkey calculation
to drivers. This is the first step of the AES-CMAC
cipher key setup and may be required for CMAC hardware
offloading.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Before, a mesh STA would execute some code on behalf of AP or IBSS
beacons. Since the mesh stack currently does not consider anything but
other mesh STAs interesting, limit processing to just these and save a
little overhead.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
WDS is (currently) not allowed when channel
contexts are *supported*, not when they're
*not* supported. Fix the inverted test.
Reported-by: Ronald <ronald645@gmail.com>
Tested-by: Ronald <ronald645@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch prepares mac80211 for a later implementation of mesh or
ad-hoc powersave clients.
The structures related to powersave (buffer, TIM map, counters) are
moved from the AP-specific interface structure to a generic structure
that can be embedded into any interface type.
The functions related to powersave are prepared to allow easy
extension with different interface types. For example with:
+ } else if (sta->sdata->vif.type == NL80211_IFTYPE_MESH_POINT) {
+ ps = &sdata->u.mesh.ps;
Some references to the AP's beacon structure are removed where they
were obviously not used.
The patch compiles without warning and has been briefly tested as AP
interface with one client in PS mode.
Signed-off-by: Marco Porsch <marco.porsch@etit.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the user wants to scan using a vif configured as AP,
cfg80211 must give him a chance to do it, even if this
will disrupt the stations performance due to off-channel
scanning. To do so, this patch adds a 'force' flag to the
SCAN_TRIGGER command which tells cfg80211 to perform the
scanning operation even if the vif is an AP and the
beaconing has already started.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Also add tracing to the API functions that drivers
(and mac80211) can call in cfg80211.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add tracing to make debugging cfg80211/mac80211
(or full-mac driver) interaction easier.
Signed-off-by: Beni Lev <beni.lev@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Hila Gonen <hila.gonen@intel.com>
Tested-by: Hila Gonen <hila.gonen@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[add a cast to int to sizeof() to avoid warning]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will allow adding central tracing like in mac80211.
Signed-off-by: Hila Gonen <hila.gonen@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, a user is allowed to choose a HT operating channel
with WEP when creating an IBSS network. WEP is not allowed
in HT configuration - this patch ensures that such requests
are denied.
Signed-off-by: Sujith Manoharan <c_manoha@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The internal function mac80211_format_buffer() has a
printf-style argument list, so add the attribute to
have gcc verify that list.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a number of unused variables that gcc
pointed out (when building with W=1) as well as
some conditions that can never be true due to
the datatypes used: unsigned values can't be
less than zero. Remove this code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no vendor-specific mesh sync implemented
and there don't need to be dummy handlers that
only print messages, so remove that code. While
at it, also constify the mesh sync ops.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
WLAN_EID_WPA and WLAN_EID_GENERIC mapped to the same value
as WLAN_EID_VENDOR_SPECIFIC. The last one being more in line
with the standard specification. Removing WLAN_EID_WPA and
WLAN_EID_GENERIC as there are no longer drivers using these.
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The include file linux/ieee80211.h contains three definitions for
the same thing in enum ieee80211_eid due to historic changes:
/* Information Element IDs */
enum ieee80211_eid {
:
WLAN_EID_WPA = 221,
WLAN_EID_GENERIC = 221,
WLAN_EID_VENDOR_SPECIFIC = 221,
:
};
The standard refers to this as "vendor specific" element so the
other two definitions are better not used. This patch changes the
wireless drivers to use one definition, ie. WLAN_EID_VENDOR_SPECIFIC.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The include file linux/ieee80211.h contains three definitions for
the same thing in enum ieee80211_eid due to historic changes:
/* Information Element IDs */
enum ieee80211_eid {
:
WLAN_EID_WPA = 221,
WLAN_EID_GENERIC = 221,
WLAN_EID_VENDOR_SPECIFIC = 221,
:
};
The standard refers to this as "vendor specific" element so the
other two definitions are better not used. This patch changes the
wireless drivers to use one definition, ie. WLAN_EID_VENDOR_SPECIFIC.
Cc: Jouni Malinen <j@w1.fi>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com> [ath6kl]
Acked-by: Bing Zhao <bzhao@marvell.com> [mwifiex]
Acked-by: Stanislav Yakovlev <stas.yakovlev@gmail.com> [ipw2x00]
Signed-off-by: Arend van Spriel <arend@broadcom.com>
[change libipw as well]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Initialization of beacon transmission in IBSS mode depends
on whether a new BSS is being created or joined. When joining
an existing IBSS network, beaconing has to start only after
a TSF-sync has happened - this is explained in 11.1.4.
Introduce a new parameter in the BSS information structure to
indicate creator/joiner mode.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use NL80211_SCAN_FLAG_LOW_PRIORITY flag in mac80211's scan state
machine to prematurely terminate scan operations if outbound
traffic collides. This is useful for marking background scans so
they don't affect throughput.
Signed-off-by: Sam Leffler <sleffler@chromium.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
[set feature flag only if software scan is used]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add an NL80211_SCAN_FLAG_FLUSH flag that causes old bss cache
entries to be flushed on scan completion. This is useful for
collecting guaranteed fresh scan/survey result (e.g. on resume).
For normal scan, flushing only happens on successful completion
of a scan; i.e. it does not happen if the scan is aborted.
For scheduled scan, previous scan results are flushed everytime
when we get new scan results.
This feature is enabled by default. Drivers can disable it by
unsetting the NL80211_FEATURE_SCAN_FLUSH flag.
Signed-off-by: Sam Leffler <sleffler@chromium.org>
Tested-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
[invert polarity of feature flag to account for old kernels]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The next patch will introduce a flag that is set
by default in cfg80211 so drivers and mac80211
need to use |= to set features they have so that
they don't clear the already-set feature.
We could set the flag in wiphy_register() instead
of wiphy_new() to avoid this patch, but then the
drivers couldn't *unset* flags they don't want to
use even though the implementation is generic.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add NL80211_SCAN_FLAG_LOW_PRIORITY flag support. It tells drivers
that this is a low priority scan request, so that they can take
necessary action.
Drivers need to advertise low priority scan capability during
registration.
Signed-off-by: Sam Leffler <sleffler@chromium.org>
Tested-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
bss_release() and __cfg80211_unlink_bss() function definitions
are moved at the begining of the file. They are used in next
patch in this series.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a flags word to direct and scheduled scan requests; it will
be used for control of optional behaviours such as flushing the
bss cache prior to doing a scan.
Signed-off-by: Sam Leffler <sleffler@chromium.org>
Tested-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Save the AP's VHT capabilities (in managed
mode) and make them available to the driver
in the station information.
Unlike HT capabilities, they aren't restricted
to the common capabilities, so drivers must be
aware of their own capabilities.
Signed-off-by: Mahesh Palivela <maheshp@posedge.com>
[fix endian conversion bug ...]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rename struct ieee80211_vht_capabilities to ieee80211_vht_cap
and renamed its member vht_capabilities_info to vht_cap_info.
Signed-off-by: Mahesh Palivela <maheshp@posedge.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
estab_plinks is not a statistics member. Hence move estab_plinks from
struct mesh_stat to struct ieee80211_if_mesh
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_sta_expire will be called by both IBSS and mesh
interfaces to account for inactive stations, so it would be more
appropriate to use sta_dbg instead of ibss_dbg.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
SAE uses two rounds of Authentication frames and both rounds require
considerable calculation to be done. This commit extends the existing
station mode authentication request to allow more control for user
space programs to build the SAE fields and to run the authentication
step ones. Only the second round with authentication transaction
sequence 2 will result in moving to authenticated state.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
SAE extends Authentication frames with fields that are not information
elements. NL80211_ATTR_IE is not suitable for these, so introduce a new
attribute that can be used to specify the fields needed for SAE in
station mode.
Signed-off-by: Jouni Malinen <j@w1.fi>
[change to verify that SAE is only used with authenticate command]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is useful when debugging authentication process issues.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Non-zero status code may be needed for Authentication frames, e.g.,
when using SAE.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers may need to iterate the active channel
contexts, export an iterator function to allow
that. To make it possible, use RCU-safe list
functions.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On each channel that the device is operating on, it
may need to listen using one or more chains depending
on the SMPS settings of the interfaces using it. The
previous channel context changes completely removed
this ability (before, it was available as the SMPS
mode).
Add per-context tracking of the required static and
dynamic RX chains and notify the driver on changes.
To achieve this, track the chains and SMPS mode used
on each virtual interface and update the channel
context whenever this changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of operating on a single channel only,
use the new channel context infrastructure in
all mac80211 code.
This enables drivers that want to use the new
channel context infrastructure to use multiple
channels, while nothing should change for all
the other drivers that don't support it.
Right now this disables both TX power settings
and spatial multiplexing powersave. Both need
to be re-enabled on a channel context basis.
Additionally, when channel contexts are used
drop the connection when channel switch is
received rather than trying to handle it. This
will have to be improved later.
[With fixes from Eliad and Emmanuel incorporated]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Depending on the driver, channel contexts may be used or
not. If they are used, the driver must have support for
hardware scan and remain-on-channel; otherwise the driver
must not advertise support for multiple channels.
Also prohibit WDS type interfaces when channel contexts
are to be used as there's no clear definition of which
channel they use.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reuse channels with compatible channel types. Some
channel types are compatible and can be used
concurrently.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Channel context pointer will be accessible on
both assign and unassign events.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce channel context driver methods. The channel
on a context channel is immutable, but the channel type
and other properties can change.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Channel context are the foundation for multi-channel
operation. They are are immutable and are re-created
(or re-used if other interfaces are bound to a certain
channel and a compatible channel type) on channel
switching.
This is an initial implementation and more features
will come in separate patches.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
[some changes including RCU protection]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull MIPS update from Ralf Baechle:
"Cleanups and fixes for breakage that occured earlier during this merge
phase. Also a few patches that didn't make the first pull request.
Of those is the Alchemy work that merges code for many of the SOCs and
evaluation boards thus among other code shrinkage, reduces the number
of MIPS defconfigs by 5."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (22 commits)
MIPS: SNI: Switch RM400 serial to SCCNXP driver
MIPS: Remove unused empty_bad_pmd_table[] declaration.
MIPS: MT: Remove kspd.
MIPS: Malta: Fix section mismatch.
MIPS: asm-offset.c: Delete unused irq_cpustat_t struct offsets.
MIPS: Alchemy: Merge PB1100/1500 support into DB1000 code.
MIPS: Alchemy: merge PB1550 support into DB1550 code
MIPS: Alchemy: Single kernel for DB1200/1300/1550
MIPS: Optimize TLB refill for RI/XI configurations.
MIPS: proc: Cleanup printing of ASEs.
MIPS: Hardwire detection of DSP ASE Rev 2 for systems, as required.
MIPS: Add detection of DSP ASE Revision 2.
MIPS: Optimize pgd_init and pmd_init
MIPS: perf: Add perf functionality for BMIPS5000
MIPS: perf: Split the Kconfig option CONFIG_MIPS_MT_SMP
MIPS: perf: Remove unnecessary #ifdef
MIPS: perf: Add cpu feature bit for PCI (performance counter interrupt)
MIPS: perf: Change the "mips_perf_event" table unsupported indicator.
MIPS: Align swapper_pg_dir to 64K for better TLB Refill code.
vmlinux.lds.h: Allow architectures to add sections to the front of .bss
...
Pull module signing support from Rusty Russell:
"module signing is the highlight, but it's an all-over David Howells frenzy..."
Hmm "Magrathea: Glacier signing key". Somebody has been reading too much HHGTTG.
* 'modules-next' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (37 commits)
X.509: Fix indefinite length element skip error handling
X.509: Convert some printk calls to pr_devel
asymmetric keys: fix printk format warning
MODSIGN: Fix 32-bit overflow in X.509 certificate validity date checking
MODSIGN: Make mrproper should remove generated files.
MODSIGN: Use utf8 strings in signer's name in autogenerated X.509 certs
MODSIGN: Use the same digest for the autogen key sig as for the module sig
MODSIGN: Sign modules during the build process
MODSIGN: Provide a script for generating a key ID from an X.509 cert
MODSIGN: Implement module signature checking
MODSIGN: Provide module signing public keys to the kernel
MODSIGN: Automatically generate module signing keys if missing
MODSIGN: Provide Kconfig options
MODSIGN: Provide gitignore and make clean rules for extra files
MODSIGN: Add FIPS policy
module: signature checking hook
X.509: Add a crypto key parser for binary (DER) X.509 certificates
MPILIB: Provide a function to read raw data into an MPI
X.509: Add an ASN.1 decoder
X.509: Add simple ASN.1 grammar compiler
...
