The check that the event is actually for this device should be moved
from the "port" handler to the net device handler.
Otherwise the port handler will deny bonding configuration for other
net devices in the same system (like enetc in the LS1028A) that don't
have the lag_upper_info->tx_type restriction that ocelot has.
Fixes: dc96ee3730 ("net: mscc: ocelot: add bonding support")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy_init_hw() function may reset the PHY to a configuration
that does not match manual network settings stored in the phydev
structure. If the phy state machine is polled rather than event
driven this can create a timing hazard where the phy state machine
might alter the settings stored in the phydev structure from the
value read from the BMCR.
This commit follows invocations of phy_init_hw() by the bcmgenet
driver with invocations of the genphy_config_aneg() function to
ensure that the BMCR is written to match the settings held in the
phydev structure. This prevents the risk of manual settings being
accidentally altered.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 1f51548627.
This commit improved the chances of the umac resetting cleanly by
ensuring that the PHY was restored to its normal operation prior
to resetting the umac. However, there were still cases when the
PHY might not be driving a Tx clock to the umac during this window
(e.g. when the PHY detects no link).
The previous commit now ensures that the unimac receives clocks
from the MAC during its reset window so this commit is no longer
needed. This commit also has an unintended negative impact on the
MDIO performance of the UniMAC MDIO interface because it is used
before the MDIO interrupts are reenabled, so it should be removed.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noted in commit 28c2d1a7a0 ("net: bcmgenet: enable loopback
during UniMAC sw_reset") the UniMAC must be clocked while sw_reset
is asserted for its state machines to reset cleanly.
The transmit and receive clocks used by the UniMAC are derived from
the signals used on its PHY interface. The bcmgenet MAC can be
configured to work with different PHY interfaces including MII,
GMII, RGMII, and Reverse MII on internal and external interfaces.
Unfortunately for the UniMAC, when configured for MII the Tx clock
is always driven from the PHY which places it outside of the direct
control of the MAC.
The earlier commit enabled a local loopback mode within the UniMAC
so that the receive clock would be derived from the transmit clock
which addressed the observed issue with an external GPHY disabling
it's Rx clock. However, when a Tx clock is not available this
loopback is insufficient.
This commit implements a workaround that leverages the fact that
the MAC can reliably generate all of its necessary clocking by
enterring the external GPHY RGMII interface mode with the UniMAC in
local loopback during the sw_reset interval. Unfortunately, this
has the undesirable side efect of the RGMII GTXCLK signal being
driven during the same window.
In most configurations this is a benign side effect as the signal
is either not routed to a pin or is already expected to drive the
pin. The one exception is when an external MII PHY is expected to
drive the same pin with its TX_CLK output creating output driver
contention.
This commit exploits the IEEE 802.3 clause 22 standard defined
isolate mode to force an external MII PHY to present a high
impedance on its TX_CLK output during the window to prevent any
contention at the pin.
The MII interface is used internally with the 40nm internal EPHY
which agressively disables its clocks for power savings leading to
incomplete resets of the UniMAC and many instabilities observed
over the years. The workaround of this commit is expected to put
an end to those problems.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the exit/unregistration process of the RmNet driver, the function
rmnet_unregister_real_device() is called to handle freeing the driver's
internal state and removing the RX handler on the underlying physical
device. However, the order of operations this function performs is wrong
and can lead to a use after free of the rmnet_port structure.
Before calling netdev_rx_handler_unregister(), this port structure is
freed with kfree(). If packets are received on any RmNet devices before
synchronize_net() completes, they will attempt to use this already-freed
port structure when processing the packet. As such, before cleaning up any
other internal state, the RX handler must be unregistered in order to
guarantee that no further packets will arrive on the device.
Fixes: ceed73a2cf ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reason for the pre-allocation of one CQE is to enable resizing of
the CQ.
Fix comment accordingly.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.com>
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the DSA core doing the call to dsa_port_disable() we do not need to
do that within the driver itself. This could cause an use after free
since past dsa_unregister_switch() we should not be accessing any
dsa_switch internal structures.
Fixes: 0394a63acf ("net: dsa: enable and disable all ports")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects the SPDX License Identifier style in
header files related to Hisilicon network devices. For C header files
Documentation/process/license-rules.rst mandates C-like comments
(opposed to C source files where C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since de77ecd4ef ("bonding: improve link-status update in
mii-monitoring"), the bonding driver has utilized two separate variables
to indicate the next link state a particular slave should transition to.
Each is used to communicate to a different portion of the link state
change commit logic; one to the bond_miimon_commit function itself, and
another to the state transition logic.
Unfortunately, the two variables can become unsynchronized,
resulting in incorrect link state transitions within bonding. This can
cause slaves to become stuck in an incorrect link state until a
subsequent carrier state transition.
The issue occurs when a special case in bond_slave_netdev_event
sets slave->link directly to BOND_LINK_FAIL. On the next pass through
bond_miimon_inspect after the slave goes carrier up, the BOND_LINK_FAIL
case will set the proposed next state (link_new_state) to BOND_LINK_UP,
but the new_link to BOND_LINK_DOWN. The setting of the final link state
from new_link comes after that from link_new_state, and so the slave
will end up incorrectly in _DOWN state.
Resolve this by combining the two variables into one.
Reported-by: Aleksei Zakharov <zakharov.a.g@yandex.ru>
Reported-by: Sha Zhang <zhangsha.zhang@huawei.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Fixes: de77ecd4ef ("bonding: improve link-status update in mii-monitoring")
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In mcp251x_restart_work_handler() the variable to stop the interrupt
handler (priv->force_quit) is reset after the chip is restarted and thus
a interrupt might occur.
This patch fixes the potential race condition by resetting force_quit
before enabling interrupts.
Signed-off-by: Timo Schlüßler <schluessler@krause.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
While the ti_hecc has interrupts to report when the error counters increase
to a certain level and which change state it doesn't handle the case that
the error counters go down again, so the reported state can actually be
wrong. Since there is no interrupt for that, do update state based on the
error counters, when the state is not error active and goes down again.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The HECC_CANES register handles the flags specially, it only updates
the flags after a one is written to them. Since the interrupt for
frame errors is not enabled an old error can hence been seen when a
state interrupt arrives. For example if the device is not connected
to the CAN-bus the error warning interrupt will have HECC_CANES
indicating there is no ack. The error passive interrupt thereafter
will have HECC_CANES flagging that there is a warning level. And if
thereafter there is a message successfully send HECC_CANES points to
an error passive event, while in reality it became error warning
again. In summary, the state is not always reported correctly.
So handle the state changes and frame errors separately. The state
changes are now based on the interrupt flags and handled directly
when they occur. The reporting of the frame errors is still done as
before, as a side effect of another interrupt.
note: the hecc_clear_bit will do a read, modify, write. So it will
not only clear the bit, but also reset all other bits being set as
a side affect, hence it is replaced with only clearing the flags.
note: The HECC_CANMC_CCR is no longer cleared in the state change
interrupt, it is completely unrelated.
And use net_ratelimit to make checkpatch happy.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When the rx FIFO overflows the ti_hecc would silently drop them since
the overwrite protection is enabled for all mailboxes. So disable it for
the lowest priority mailbox and return a proper error value when receive
message lost is set. Drop the message itself in that case, since it
might be partially updated.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Acked-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Release the mailbox after reading it, so it can be reused a bit earlier.
Since "can: rx-offload: continue on error" all pending message bits are
cleared directly, so remove clearing them in ti_hecc.
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The HECC_CANMIM is set in the xmit path and cleared in the interrupt.
Since this is done with a read, modify, write action the register might
end up with some more MIM enabled then intended, since it is not
protected. That doesn't matter at all, since the tx interrupt disables
the mailbox with HECC_CANME (while holding a spinlock). So lets just
always keep MIM set.
While at it, since the mailbox direction never changes, don't set it
every time a message is send, ti_hecc_reset() already sets them to tx.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When the interface goes down, the CPK should no longer take an active
part in the CAN-bus communication, like sending acks and error frames.
So enable configuration mode in ti_hecc_stop, so the CPK is no longer
active.
When a transceiver switch is present the acks and errors don't make it
to the bus, but disabling the CPK then does prevent oddities, like
ti_hecc_reset() failing, since the CPK can become bus-off and starts
counting the 11 bit recessive bits, which seems to block the reset. It
can also cause invalid interrupts and disrupt the CAN-bus, since
transmission can be stopped in the middle of a message, by disabling the
tranceiver while the CPK is sending.
Since the CPK is disabled after normal power on, it is typically only
seen when the interface is restarted.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The call to can_rx_offload_queue_sorted() may fail and return an error
(in the current implementation due to resource shortage). The passed skb
is consumed.
This patch adds incrementing of the appropriate error counters to let
the device statistics reflect that there's a problem.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The call to can_rx_offload_queue_sorted() may fail and return an error
(in the current implementation due to resource shortage). The passed skb
is consumed.
This patch adds incrementing of the appropriate error counters to let
the device statistics reflect that there's a problem.
Reported-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In case of a resource shortage, i.e. the rx_offload queue will overflow
or a skb fails to be allocated (due to OOM),
can_rx_offload_offload_one() will call mailbox_read() to discard the
mailbox and return an ERR_PTR.
If the hardware FIFO is empty can_rx_offload_offload_one() will return
NULL.
In case a CAN frame was read from the hardware,
can_rx_offload_offload_one() returns the skb containing it.
Without this patch can_rx_offload_irq_offload_fifo() bails out if no skb
returned, regardless of the reason.
Similar to can_rx_offload_irq_offload_timestamp() in case of a resource
shortage the whole FIFO should be discarded, to avoid an IRQ storm and
give the system some time to recover. However if the FIFO is empty the
loop can be left.
With this patch the loop is left in case of empty FIFO, but not on
errors.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In case of a resource shortage, i.e. the rx_offload queue will overflow
or a skb fails to be allocated (due to OOM),
can_rx_offload_offload_one() will call mailbox_read() to discard the
mailbox and return an ERR_PTR.
However can_rx_offload_irq_offload_timestamp() bails out in the error
case. In case of a resource shortage all mailboxes should be discarded,
to avoid an IRQ storm and give the system some time to recover.
Since can_rx_offload_irq_offload_timestamp() is typically called from a
while loop, all message will eventually be discarded. So let's continue
on error instead to discard them directly.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Before this patch can_rx_offload_offload_one() returns a pointer to a
skb containing the read CAN frame or a NULL pointer.
However the meaning of the NULL pointer is ambiguous, it can either mean
the requested mailbox is empty or there was an error.
This patch fixes this situation by returning:
- pointer to skb on success
- NULL pointer if mailbox is empty
- ERR_PTR() in case of an error
All users of can_rx_offload_offload_one() have been adopted, no
functional change intended.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If the rx-offload skb_queue is full or the skb allocation fails (due to OOM),
the mailbox contents is discarded.
This patch adds the incrementing of the rx_fifo_errors statistics counter.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The skb_queue is a linked list, holding the skb to be processed in the
next NAPI call.
Without this patch, the queue length in can_rx_offload_offload_one() is
limited to skb_queue_len_max + 1. As the skb_queue is a linked list, no
array or other resources are accessed out-of-bound, however this
behaviour is counterintuitive.
This patch limits the rx-offload skb_queue length to skb_queue_len_max.
Fixes: d254586c34 ("can: rx-offload: Add support for HW fifo based irq offloading")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If the rx-offload skb_queue is full can_rx_offload_queue_tail() will not
queue the skb and return with an error.
This patch frees the skb in case of a full queue, which brings
can_rx_offload_queue_tail() in line with the
can_rx_offload_queue_sorted() function, which has been adjusted in the
previous patch.
The return value is adjusted to -ENOBUFS to better reflect the actual
problem.
The device stats handling is left to the caller.
Fixes: d254586c34 ("can: rx-offload: Add support for HW fifo based irq offloading")
Reported-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If the rx-offload skb_queue is full can_rx_offload_queue_sorted() will
not queue the skb and return with an error.
None of the callers of this function, issue a kfree_skb() to free the
not queued skb. This results in a memory leak.
This patch fixes the problem by freeing the skb in case of a full queue.
The return value is adjusted to -ENOBUFS to better reflect the actual
problem.
The device stats handling is left to the callers, as this function might
be used in both the rx and tx path.
Fixes: 55059f2b7f ("can: rx-offload: introduce can_rx_offload_get_echo_skb() and can_rx_offload_queue_sorted() functions")
Cc: linux-stable <stable@vger.kernel.org>
Cc: Martin Hundebøll <martin@geanix.com>
Reported-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
AXI CANIP doesn't support tx fifo empty interrupt feature(TXFEMP),
update the flags filed in the driver for AXI CAN case accordingly.
Fixes: 3281b380ec ("can: xilinx_can: Fix flags field initialization for axi can and canps")
Reported-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
While the state is updated when the error counters increase and
decrease, there is no event when the bus recovers and the error counters
decrease again. So add that event as well.
Change the state going downward to be ERROR_PASSIVE -> ERROR_WARNING ->
ERROR_ACTIVE instead of directly to ERROR_ACTIVE again.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Acked-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Tested-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When the CAN interface is closed it the hardwre is put in power down
mode, but does not reset the error counters / state. Reset the D_CAN on
open, so the reported state and the actual state match.
According to [1], the C_CAN module doesn't have the software reset.
[1] http://www.bosch-semiconductors.com/media/ip_modules/pdf_2/c_can_fd8/users_manual_c_can_fd8_r210_1.pdf
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When the status register is read without the status IRQ pending, the
chip may not raise the interrupt line for an upcoming status interrupt
and the driver may miss a status interrupt.
It is critical that the BUSOFF status interrupt is forwarded to the
higher layers, since no more interrupts will follow without
intervention.
Thanks to Wolfgang and Joe for bringing up the first idea.
Signed-off-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Joe Burmeister <joe.burmeister@devtank.co.uk>
Fixes: fa39b54ccf ("can: c_can: Get rid of pointless interrupts")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
While the state changes are reported when the error counters increase
and decrease, there is no event when the bus recovers and the error
counters decrease again. So add those as well.
Change the state going downward to be ERROR_PASSIVE -> ERROR_WARNING ->
ERROR_ACTIVE instead of directly to ERROR_ACTIVE again.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fix a small slab info leak due to a failure to clear the command buffer
at allocation.
The first 16 bytes of the command buffer are always sent to the device
in pcan_usb_send_cmd() even though only the first two may have been
initialised in case no argument payload is provided (e.g. when waiting
for a response).
Fixes: bb4785551f ("can: usb: PEAK-System Technik USB adapters driver core")
Cc: stable <stable@vger.kernel.org> # 3.4
Reported-by: syzbot+863724e7128e14b26732@syzkaller.appspotmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When decoding a buffer received from PCAN-USB, the first timestamp read in
a packet is a 16-bit coded time base, and the next ones are an 8-bit
offset to this base, regardless of the type of packet read.
This patch corrects a potential loss of synchronization by using a
timestamp index read from the buffer, rather than an index of received
data packets, to determine on the sizeof the timestamp to be read from the
packet being decoded.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Fixes: 46be265d33 ("can: usb: PEAK-System Technik PCAN-USB specific part")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The ECC (memory error detection and correction) mechanism can be
activated or not, controlled by the ECCDIS bit in CAN_MECR. When
disabled, updates on indications and reporting registers are stopped.
So if want to disable ECC completely, had better assert ECCDIS bit, not
just mask the related interrupts.
Fixes: cdce844865 ("can: flexcan: add vf610 support for FlexCAN")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The driver was accessing its driver data after having freed it.
Fixes: 0024d8ad16 ("can: usb_8dev: Add support for USB2CAN interface from 8 devices")
Cc: stable <stable@vger.kernel.org> # 3.9
Cc: Bernd Krumboeck <b.krumboeck@gmail.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The driver was accessing its driver data after having freed it.
Fixes: 51f3baad7d ("can: mcba_usb: Add support for Microchip CAN BUS Analyzer")
Cc: stable <stable@vger.kernel.org> # 4.12
Cc: Remigiusz Kołłątaj <remigiusz.kollataj@mobica.com>
Reported-by: syzbot+e29b17e5042bbc56fae9@syzkaller.appspotmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In gs_can_open() if usb_submit_urb() fails the allocated urb should be
released.
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
of_node_put() needs to be called when the device node which is got
from of_get_child_by_name() finished using.
Fixes: 2290aefa2e ("can: dev: Add support for limiting configured bitrate")
Cc: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Wen Yang <wenyang@linux.alibaba.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This driver forgets to disable and unprepare clks when remove.
Add calls to clk_disable_unprepare to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported in [0] at least one RTL8168dp version has problems
establishing a link. This chip version has an integrated RTL8211b PHY,
however the chip seems to report a wrong PHY ID, resulting in a wrong
PHY driver (for Generic Realtek PHY) being loaded.
Work around this issue by adding a hook to r8168dp_2_mdio_read()
for returning the correct PHY ID.
[0] https://bbs.archlinux.org/viewtopic.php?id=246508
Fixes: 242cd9b586 ("r8169: use phy_resume/phy_suspend")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since it became possible for the DSA core to use a CPU port different
than 8, our bcm_sf2_imp_setup() function was broken because it assumes
that registers are applicable to port 8. In particular, the port's MAC
is going to stay disabled, so make sure we clear the RX_DIS and TX_DIS
bits if we are not configured for port 8.
Fixes: 9f91484f6f ("net: dsa: make "label" property optional for dsa2")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phylink_dbg() macro does not follow dynamic debug or defined(DEBUG)
and as a result, it spams the kernel log since a PR_DEBUG level is
currently used. Fix it to be defined appropriately whether
CONFIG_DYNAMIC_DEBUG or defined(DEBUG) are set.
Fixes: 17091180b1 ("net: phylink: Add phylink_{printk, err, warn, info, dbg} macros")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Synces the DMA buffer properly in order for CPU and device to see
the most up-to-data data.
Signed-off-by: Yangchun Fu <yangchun@google.com>
Reviewed-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2019-11-01
This series contains updates to e1000, igb, igc, ixgbe, i40e and driver
documentation.
Lyude Paul fixes an issue where a fatal read error occurs when the
device is unplugged from the machine. So change the read error into a
warn while the device is still present.
Manfred Rudigier found that the i350 device was not apart of the "Media
Auto Sense" feature, yet the device supports it. So add the missing
i350 device to the check and fix an issue where the media auto sense
would flip/flop when no cable was connected to the port causing spurious
kernel log messages.
I fixed an issue where the fix to resolve receive buffer starvation was
applied in more than one place in the driver, one being the incorrect
location in the i40e driver.
Wenwen Wang fixes a potential memory leak in e1000 where allocated
memory is not properly cleaned up in one of the error paths.
Jonathan Neuschäfer cleans up the driver documentation to be consistent
and remove the footnote reference, since the footnote no longer exists in
the documentation.
Igor Pylypiv cleans up a duplicate clearing of a bit, no need to clear
it twice.
v2: Fixed alignment issue in patch 3 of the series based on community
feedback.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
__IXGBE_RX_BUILD_SKB_ENABLED bit is already cleared.
Signed-off-by: Igor Pylypiv <igor.pylypiv@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In e1000_set_ringparam(), 'tx_old' and 'rx_old' are not deallocated if
e1000_up() fails, leading to memory leaks. Refactor the code to fix this
issue.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Magnus's fix to resolve a potential receive buffer starvation for AF_XDP
got applied to both the i40e_xsk_umem_enable/disable() functions, when it
should have only been applied to the "enable". So clean up the undesired
code in the disable function.
CC: Magnus Karlsson <magnus.karlsson@intel.com>
Fixes: 1f459bdc20 ("i40e: fix potential RX buffer starvation for AF_XDP")
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
At least on the i350 there is an annoying behavior that is maybe also
present on 82580 devices, but was probably not noticed yet as MAS is not
widely used.
If no cable is connected on both fiber/copper ports the media auto sense
code will constantly swap between them as part of the watchdog task and
produce many unnecessary kernel log messages.
The swap code responsible for this behavior (switching to fiber) should
not be executed if the current media type is copper and there is no signal
detected on the fiber port. In this case we can safely wait until the
AUTOSENSE_EN bit is cleared.
Signed-off-by: Manfred Rudigier <manfred.rudigier@omicronenergy.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Third set of fixes for 5.4. Most of them are for iwlwifi but important
fixes also for rtlwifi and mt76, the overflow fix for rtlwifi being
most important.
iwlwifi
* fix merge damage on earlier patch
* various fixes to device id handling
* fix scan config command handling which caused firmware asserts
rtlwifi
* fix overflow on P2P IE handling
* don't deliver too small frames to mac80211
mt76
* disable PCIE_ASPM
* fix buffer DMA unmap on certain cases
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdvEesAAoJEG4XJFUm622bbQQH+we6ATCGLxEFtRhlPALEeXqk
up/eJTL+fQoZ2Z0IxarZT05rhBK9VNAiDXE2fuPB0lUuL1//7FrrG337vWFmM41b
FJE2ESf0Q8fKeceRDbe+4QgzgCSg2uSB9IgCo2jwXjTVjlFLufT8oUBGlUQU160b
L3H/GuBYNlE1dmLyBXZCqR74DRvKTf3Uh8FfHxO41Mv64LjhotXJ+tIWboUJr5N5
uU9eAyW7MV7sL+XQyN5IYIZ595gyRjIwD5U5kuX/8vEcGusqfMUKv/IBH8LFlQYl
akY9n4ozpxSxUmcors4RBjb//XihjgtDldEGxG6EqkD+0DokM+nQiYteFzgBnrE=
=sbTa
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2019-11-01' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 5.4
Third set of fixes for 5.4. Most of them are for iwlwifi but important
fixes also for rtlwifi and mt76, the overflow fix for rtlwifi being
most important.
iwlwifi
* fix merge damage on earlier patch
* various fixes to device id handling
* fix scan config command handling which caused firmware asserts
rtlwifi
* fix overflow on P2P IE handling
* don't deliver too small frames to mac80211
mt76
* disable PCIE_ASPM
* fix buffer DMA unmap on certain cases
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The remove misses to disable and unprepare priv->macclk like what is done
when probe fails.
Add the missed call in remove.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables the hardware feature "Media Auto Sense" also on the
i350. It works in the same way as on the 82850 devices. Hardware designs
using dual PHYs (fiber/copper) can enable this feature by setting the MAS
enable bits in the NVM_COMPAT register (0x03) in the EEPROM.
Signed-off-by: Manfred Rudigier <manfred.rudigier@omicronenergy.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
