Implements irq support for HDMI audio output. Now the polling timer
is only enabled if irq support isn't available.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Rework HDMI audio polling timer, only enable it when
at least one HDMI encoder needs it. Preparation for
replacing it with irq support.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: use PIPE_CONTROL instruction on Ironlake and Sandy Bridge
drm/i915: cleanup FBC buffers at unload time
drm/i915: fix tiling limits for i915 class hw v2
drm/i915: set DIDL using the ACPI video output device _ADR method return.
drm/i915: Fix 82854 PCI ID, and treat it like other 85X
drm/i915: Attempt to fix watermark setup on 85x (v2)
Since 965, the hardware has supported the PIPE_CONTROL command, which
provides fine grained GPU cache flushing control. On recent chipsets,
this instruction is required for reliable interrupt and sequence number
reporting in the driver.
So add support for this instruction, including workarounds, on Ironlake
and Sandy Bridge hardware.
https://bugs.freedesktop.org/show_bug.cgi?id=27108
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
This keeps the memory manager from complaining when we take it down.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Eric mentioned on irc this patch was bad, so revert it.
This reverts commit fb8b5a39b6.
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Drivers may use vblank calls now (e.g. drm_vblank_off) in their unload
paths, so don't clean up the vblank related structures until after
driver unload.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* drm-ttm-unmappable:
drm/radeon/kms: enable use of unmappable VRAM V2
drm/ttm: remove io_ field from TTM V6
drm/vmwgfx: add support for new TTM fault callback V5
drm/nouveau/kms: add support for new TTM fault callback V5
drm/radeon/kms: add support for new fault callback V7
drm/ttm: ttm_fault callback to allow driver to handle bo placement V6
drm/ttm: split no_wait argument in 2 GPU or reserve wait
Conflicts:
drivers/gpu/drm/nouveau/nouveau_bo.c
This patch enable the use of unmappable VRAM thanks to
previous TTM infrastructure change.
V2 update after io_mem_reserve/io_mem_free callback balancing
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
All TTM driver have been converted to new io_mem_reserve/free
interface which allow driver to choose and return proper io
base, offset to core TTM for ioremapping if necessary. This
patch remove what is now deadcode.
V2 adapt to match with change in first patch of the patchset
V3 update after io_mem_reserve/io_mem_free callback balancing
V4 adjust to minor cleanup
V5 remove the needs ioremap flag
V6 keep the ioremapping facility in TTM
[airlied- squashed driver removals in here also]
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This add the support for the new fault callback, does change anything
from driver point of view.
Improvement: store the aperture base in a variable so that we don't
call a function to get it on each fault.
Patch hasn't been tested.
V2 don't derefence bo->mem.mm_node as it's not NULL only for
VRAM or GTT
V3 update after io_mem_reserve/io_mem_free callback balancing
V4 callback has to ioremap
V5 ioremap is done by TTM
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This add the support for the new fault callback, does change anything
from driver point of view, thought it should allow nouveau to add
support for unmappable VRAM.
Improvement: store the aperture base in a variable so that we don't
call a function to get it on each fault.
Patch hasn't been tested on any hw.
V2 don't derefence bo->mem.mm_node as it's not NULL only for
VRAM or GTT
V3 update after io_mem_reserve/io_mem_free callback balancing
V4 callback has to ioremap
V5 ioremap is done by ttm
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This add the support for the new fault callback and also the
infrastructure for supporting unmappable VRAM.
V2 validate BO with no_wait = true
V3 don't derefence bo->mem.mm_node as it's not NULL only for
VRAM or GTT
V4 update to splitted no_wait ttm change
V5 update to new balanced io_mem_reserve/free change
V6 callback is responsible for iomapping memory
V7 move back iomapping to ttm
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On fault the driver is given the opportunity to perform any operation
it sees fit in order to place the buffer into a CPU visible area of
memory. This patch doesn't break TTM users, nouveau, vmwgfx and radeon
should keep working properly. Future patch will take advantage of this
infrastructure and remove the old path from TTM once driver are
converted.
V2 return VM_FAULT_NOPAGE if callback return -EBUSY or -ERESTARTSYS
V3 balance io_mem_reserve and io_mem_free call, fault_reserve_notify
is responsible to perform any necessary task for mapping to succeed
V4 minor cleanup, atomic_t -> bool as member is protected by reserve
mecanism from concurent access
V5 the callback is now responsible for iomapping the bo and providing
a virtual address this simplify TTM and will allow to get rid of
TTM_MEMTYPE_FLAG_NEEDS_IOREMAP
V6 use the bus addr data to decide to ioremap or this isn't needed
but we don't necesarily need to ioremap in the callback but still
allow driver to use static mapping
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Luckily the change is quite a little bit less invasive than I've
feared.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Thanks to the to_intel_bo helper, this change is rather trivial.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Just embed it and adjust the pointers, No other changes (that's
for later patches).
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Just preparation, no functional change.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When drivers embed the core gem object into their own structures,
they'll have to do this. Temporarily this results in an ugly
kfree(gem_obj);
in every gem driver.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This function can be used by drivers who allocate the drm gem object
on their own. No functional change in here, just preparation.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* drm-radeon-evergreen-accel:
drm/radeon: fix cypress firmware typo.
drm/radeon/kms/evergreen: add hpd support
drm/radeon/kms/evergreen: implement irq support
drm/radeon/kms/evergreen: setup and enable the CP
drm/radeon/kms/evergreen: implement gfx init
drm/radeon/kms/evergreen: add soft reset function
drm/radeon/kms/evergreen: add gart support
drm/radeon/kms: add support for evergreen power tables
drm/radeon/kms: update atombios.h power tables for evergreen
* drm-fbdev-cleanup:
drm/fb: remove drm_fb_helper_setcolreg
drm/kms/fb: use slow work mechanism for normal hotplug also.
drm/kms/fb: add polling support for when nothing is connected.
drm/kms/fb: provide a 1024x768 fbcon if no outputs found.
drm/kms/fb: separate fbdev connector list from core drm connectors
drm/kms/fb: move to using fb helper crtc grouping instead of core crtc list
drm/fb: fix fbdev object model + cleanup properly.
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/nouveau/nouveau_drv.h
* drm-edid-fixes:
drm/edid: When checking duplicate standard modes, walked the probed list
drm/edid: Fix sync polarity for secondary GTF curve
drm/modes: Fix interlaced mode names
drm/edid: Add secondary GTF curve support
drm/edid: Strengthen the algorithm for standard mode codes
drm/edid: Fix the HDTV hack.
drm/edid: Extend range-based mode addition for EDID 1.4
drm/edid: Add test for monitor reduced blanking support.
drm/edid: Fix preferred mode parse for EDID 1.4
drm/edid: Remove some silly comments
drm/edid: Remove arbitrary EDID extension limit
drm/edid: Add modes for Established Timings III section
drm/edid: Reshuffle mode list construction to closer match the spec
drm/edid: Remove a redundant check
drm/edid: Remove some misleading comments
drm/edid: Fix secondary block fetch.
* drm-ttm-pool:
drm/ttm: using kmalloc/kfree requires including slab.h
drm/ttm: include linux/seq_file.h for seq_printf
drm/ttm: Add sysfs interface to control pool allocator.
drm/ttm: Use set_pages_array_wc instead of set_memory_wc.
arch/x86: Add array variants for setting memory to wc caching.
drm/nouveau: Add ttm page pool debugfs file.
drm/radeon/kms: Add ttm page pool debugfs file.
drm/ttm: Add debugfs output entry to pool allocator.
drm/ttm: add pool wc/uc page allocator V3
* 'anholt/drm-intel-next' of /home/airlied/kernel/drm-next: (48 commits)
agp/intel-gtt: kill previous_size assignments
agp/intel-gtt: kill intel_i830_tlbflush
agp/intel: split out gmch/gtt probe, part 1
agp/intel: kill mutli_gmch_chip
agp/intel: uncoditionally reconfigure driver on resume
agp/intel: split out the GTT support
agp/intel: introduce intel-agp.h header file
drm/i915: Don't touch PORT_HOTPLUG_EN in intel_dp_detect()
drm/i915/pch: Use minimal number of FDI lanes (v2)
drm/i915: Add the support of memory self-refresh on Ironlake
drm/i915: Move Pineview CxSR and watermark code into update_wm hook.
drm/i915: Only save/restore FBC on the platform that supports FBC
drm/i915: Fix the incorrect argument for SDVO SET_TV_format command
drm/i915: Add support of SDVO on Ibexpeak PCH
drm/i915: Don't enable pipe/plane/VCO early (wait for DPMS on).
drm/i915: do not read uninitialized ->dev_private
Revert "drm/i915: Use a dmi quirk to skip a broken SDVO TV output."
drm/i915: implement multifunction SDVO device support
drm/i915: remove unused intel_pipe_get_connector()
drm/i915: remove connector object in old output structure
...
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: add FireMV 2400 PCI ID.
drm/radeon/kms: allow R500 regs VAP_ALT_NUM_VERTICES and VAP_INDEX_OFFSET
drivers/gpu/radeon: Add MSPOS regs to safe list.
drm/radeon/kms: disable the tv encoder when tv/cv is not in use
drm/radeon/kms: adjust pll settings for tv
drm/radeon/kms: fix tv dac conflict resolver
drm/radeon/kms/evergreen: don't enable hdmi audio stuff
drm/radeon/kms/atom: fix dual-link DVI on DCE3.2/4.0
drm/radeon/kms: fix rs600 tlb flush
drm/radeon/kms: print GPU family and device id when loading
drm/radeon/kms: fix calculation of mipmapped 3D texture sizes
drm/radeon/kms: only change mode when coherent value changes.
drm/radeon/kms: more atom parser fixes (v2)
[airlied: fix V_A_N_V to not be safe and fix check to make sure only r500
- bump userspace version]
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Switching between TV and VGA caused VGA to break on some systems
since the TV encoder was left enabled when VGA was used.
fixes fdo bug 25520.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On systems with the tv dac shared between DVI and TV,
we can only use the dac for one of the connectors.
However, when using a digital monitor on the DVI port,
you can use the dac for the TV connector just fine.
Check the use_digital status when resolving the conflict.
Fixes fdo bug 27649, possibly others.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Got broken during the evergreen merge.
Fixes fdo bug 27001.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Typo in in flush leaded to no flush of the RS600 tlb which
ultimately leaded to massive system ram corruption, with
this patch everythings seems to work properly.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This will help figuring out GPU when looking at bugs log.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Current code is definitely crap: Largest pitch allowed spills into
the TILING_Y bit of the fence registers ... :(
I've rewritten the limits check under the assumption that 3rd gen hw
has a 3d pitch limit of 8kb (like 2nd gen). This is supported by an
otherwise totally misleading XXX comment.
This bug mostly resulted in tiling-corrupted pixmaps because the kernel
allowed too wide buffers to be tiled. Bug brought to the light by the
xf86-video-intel 2.11 release because that unconditionally enabled
tiling for pixmaps, relying on the kernel to check things. Tiling for
the framebuffer was not affected because the ddx does some additional
checks there ensure the buffer is within hw-limits.
v2: Instead of computing the value that would be written into the
hw fence registers and then checking the limits simply check whether
the stride is above the 8kb limit. To better document the hw, add
some WARN_ONs in i915_write_fence_reg like I've done for the i830
case (using the right limits).
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=27449
Tested-by: Alexander Lam <lambchop468@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
PORT_HOTPLUG_EN has allready been setup in i915_driver_irq_postinstall(),
when intel_dp_detect() runs.
Delete the DP[BCD]_HOTPLUG_INT_EN defines, they are not referenced anymore.
I found this while searching for a fix for
https://bugzilla.redhat.com/show_bug.cgi?id=528312
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: Eric Anholt <eric@anholt.net>
we used to set the DIDL in the output device detected order.
But some BIOSes requires it to be initialized in the ACPI device order.
e.g. the value of the first field in DIDL stands for the first
ACPI video output device in ACPI namespace.
Now we initialize the DIDL using the device id, i.e. _ADR return value,
of each ACPI video device, if it is not 0.
https://bugzilla.kernel.org/show_bug.cgi?id=15054
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This should be a small power savings. Tested on Lenovo T410 (Ironlake), LVDS
VGA and DisplayPort, up to 1920x1200R.
v2: Add Sandybridge support, fix obvious math error.
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
IS_MOBILE() catches 85x, so we'd always try to use the 9xx FIFO sizing;
since there's an explicit 85x version, this seems wrong.
v2: Handle 830m correctly too.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: Ignore LVDS EDID when it is unavailabe or invalid
drm/i915: Add no_lvds entry for the Clientron U800
drm/i915: Rename many remaining uses of "output" to encoder or connector.
drm/i915: Rename intel_output to intel_encoder.
agp/intel: intel_845_driver is an agp driver!
drm/i915: introduce to_intel_bo helper
drm/i915: Disable FBC on 915GM and 945GM.
Update the self-refresh watermark for display plane/cursor and enable
the memory self-refresh on Ironlake. The watermark is also updated for
the active display plane.
More than 1W idle power is saved on one Ironlake laptop after enabling
memory self-refresh.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Previously, after setting up the Pineview CxSR state, i9xx_update_wm would
get called and overwrite our state.
BTW: We will disable the self-refresh and never enable it any more if we
can't find the appropriate the latency on pineview plaftorm. In such case
the update_wm callback will be NULL.
The bitmask macro is also defined to access the corresponding fifo
watermark register.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Otherwise it will cause that S-video output becomes black/white when
switching to other TV format.
http://bugs.freedesktop.org/show_bug.cgi?id=23916
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Tested-by: Arnold <arnold.erbsloeh@web.de>
Tested-by: Bazin <bazin.cz@gmail.com>
Tested-by: Nigel <nigel_tuck@eircom.net>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
SDVO on Ibexpeak PCH with Ironlake is multiplexed with
HDMIB port, and only has SDVOB port.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
The existing code handling the DPMS ON event is much more careful to
ensure that these registers are enabled according to strict sequencing
requirements. Enabling these early in mode_set simply defeats that.
Signed-off-by: Carl Worth <cworth@cworth.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
->dev_private at that point is NULL and is initialied only a few lines
later.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This reverts commit 6070a4a928.
The quirk for this SDVO device on IBM specific board is just a hack
in old code which showed the broken multifunction SDVO support in
the driver. Multifunction SDVO patch provided the right fix for it.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
With new intel_encoder/intel_connector structure change, each supported
connector type on SDVO device will be created as a new 'intel_connector',
and all attached to one 'intel_encoder' for its SDVO port.
The SDVO encoder will handle SDVO protocol stuff, and each connector does
its own part of work now, like detection is only to check if current active
output is itself, etc.
Update since last submit:
- Fixed SDVO TV property creation failure by incorrect set target output call
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
As all display drivers have been converted, remove the left reference
for connector object in old structure.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Probably only matters for format-converting dongles, but might as well
get it right all the time.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
DP on Cougarpoint has new training pattern definitions, and
new transcoder DP control register is used to determine the mapping
for transcoder and DP digital output. And eDP for Sandybridge has
new voltage and pre-emphasis level definitions.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
To make CRT force detect reliable on Cougarpoint, we need to
disable DAC before force detect, and restore back when trigger
is completed.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Cougarpoint is the new PCH for Sandybridge CPU. This one resolves the
chipset change for display pipeline compared to previous Ibexpeak PCH.
Sandybridge/Cougarpoint has different FDI training parameters, so this also
makes seperate FDI training functions for IBX and CPT. Other change includes
new transcoder DPLL select function to set which DPLL for transcoder to pick
up.
And with another new transcoder C introduced in Cougarpoint, each connector
has new transcoder select bits. This one adds that change to light up VGA.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
PCH is the new name for south bridge from Ironlake/Sandybridge,
which contains most of the display outputs except eDP. This one
adds a probe function to detect current PCH type, and method to
detect Cougarpoint PCH.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Integrated TV is deprecated in new chips from Ironlake.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
OpRegion event on 965G requires legacy BLC event enabled in pipe stat. As LVDS
could be on either pipe now, we should enable BLC event on both pipe. If fail to
do so, we couldn't handle the brightness request triggered from graphics
opregion.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This was brought over from UMS, and used for a while until we decided
that drm_helper_resume_force_mode was easier and more reliable, since
it didn't require duplicating all the code deleted here. We just
forgot to delete all that junk for a while.
On X startup we were getting a flicker where there shouldn't have been one.
the X DDX calls the kernel to set the properties to the same values (yes
it could be smarter), however the kernel was doing a pointless modeset then,
making my nice smooth boot ugly.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This trys to shut up complains about invalid LVDS EDID during
mode probe, but uses fixed panel mode directly for panels with
broken EDID.
https://bugs.freedesktop.org/show_bug.cgi?id=23099https://bugs.freedesktop.org/show_bug.cgi?id=26395
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
shr/shl ops need the full dst rather than the pre-masked
version. Fixes fdo bug 27478 and kernel bug 15738.
v2: remove some unsed vars, add comments
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This one replaces original param for intel_ddc_get_modes() with
DRM connector and i2c bus adapter instead. With explicit params,
we won't require that a single driver structure must hold connector
and DDC bus reference, which ease the conversion to splitted encoder/
connector model.
It also clears up for some cases that we would steal other DDC bus
for mode probe, like VGA analog DDC probe for DVI-I. Also it fixed
a bug in old DVI-I probe handling, that failed to restore origin
analog GPIO port.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
In load detection, connector's encoder assignment must be kept
consistent for proper mode setting, and this makes connector as
explicit parameter for load detect function to not require single
data structure to hold both encoder and connector reference, ease
the transition for splitted encoder/connector model.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
For introducing splitted encoder/connector structure, this helper will return
connector's attached encoder when needed.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This adds new structure of intel_connector to present drm's
connector object, which is used to convert from origin single
output into encoder/connector model.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
What we really want is encoder info instead of connector, so change
some more list walk in pipeline setup functions from connector_list
to encoder_list.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Instead of walking through drm connector_list uses encoder_list
for calling hotplug functions which is consistent with intel display
hotplug reporting.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The TV detection logic is not reliable on the Cantiga platform.
Sometimes the TV will be misdetected as the following two cases:
- TV is misdetected on some laptops. e.g. There is no TV connector
port or no TV is attached. But the TV is shown as connected.
- TV connector type is misdetected. e.g. the component TV is
attached, but the TV is shown as S-video type.
According to the hardware requirement, the TV sense state bits of TV DAC
register should be cleared to zero on Cantiga platfrom.
https://bugzilla.kernel.org/show_bug.cgi?id=14792
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Tested-by: Santi <santi@agolina.net>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (29 commits)
drm/nouveau: bail out of auxch transaction if we repeatedly recieve defers
drm/nv50: implement gpio set/get routines
drm/nv50: parse/use some more de-magiced parts of gpio table entries
drm/nouveau: store raw gpio table entry in bios gpio structs
drm/nv40: Init some tiling-related PGRAPH state.
drm/nv50: Add NVA3 support in ctxprog/ctxvals generator.
drm/nv50: another dodgy DP hack
drm/nv50: punt hotplug irq handling out to workqueue
drm/nv50: preserve an unknown SOR_MODECTRL value for DP encoders
drm/nv50: Allow using the NVA3 new compute class.
drm/nv50: cleanup properly if PDISPLAY init fails
drm/nouveau: fixup the init failure paths some more
drm/nv50: fix instmem init on IGPs if stolen mem crosses 4GiB mark
drm/nv40: add LVDS table quirk for Dell Latitude D620
drm/nv40: rework lvds table parsing
drm/nouveau: detect vram amount once, and save the value
drm/nouveau: remove some unused members from drm_nouveau_private
drm/nouveau: Make use of TTM busy_placements.
drm/nv50: add more 0x100c80 flushy magic
drm/nv50: fix fbcon when framebuffer above 4GiB mark
...
* 'nouveau/for-airlied' of ../drm-nouveau-next: (21 commits)
drm/nouveau: bail out of auxch transaction if we repeatedly recieve defers
drm/nv50: implement gpio set/get routines
drm/nv50: parse/use some more de-magiced parts of gpio table entries
drm/nouveau: store raw gpio table entry in bios gpio structs
drm/nv40: Init some tiling-related PGRAPH state.
drm/nv50: Add NVA3 support in ctxprog/ctxvals generator.
drm/nv50: another dodgy DP hack
drm/nv50: punt hotplug irq handling out to workqueue
drm/nv50: preserve an unknown SOR_MODECTRL value for DP encoders
drm/nv50: Allow using the NVA3 new compute class.
drm/nv50: cleanup properly if PDISPLAY init fails
drm/nouveau: fixup the init failure paths some more
drm/nv50: fix instmem init on IGPs if stolen mem crosses 4GiB mark
drm/nv40: add LVDS table quirk for Dell Latitude D620
drm/nv40: rework lvds table parsing
drm/nouveau: detect vram amount once, and save the value
drm/nouveau: remove some unused members from drm_nouveau_private
drm/nouveau: Make use of TTM busy_placements.
drm/nv50: add more 0x100c80 flushy magic
drm/nv50: fix fbcon when framebuffer above 4GiB mark
...
The command processor (CP) fetches command buffers and
feeds the GPU. This patch requires the evergreen
family me and pfp ucode files.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This initializes the gfx engine so accel can
eventually be used.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes garbled 3D on an nv46 card.
Reported-by: Francesco Marella <francesco.marella@gmail.com>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Allows *some* DP cards to keep working in some corner cases that most
people shouldn't hit. I hit it all the time with development, so this
can stay for now.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This value interacts with some registers we don't currently know how to
program properly ourselves. The default of 5 that we were using matches
what the VBIOS on early DP cards do, but later ones use 6, which would
cause nouveau to program an incorrect mode on these chips.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Gart setup is more or less like r7xx. Copy
rv770d.h to evergreend.h and fix up changes.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
All indications seem to be that the version 0x30 table should be handled
the same way as 0x40 (as used on G80), at least for the parts that we
currently try use.
This commit cleans up the parsing to make it clearer about what we're
actually trying to achieve, and unifies the 0x30/0x40 parsing.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
As opposed to repeatedly reading the amount back from the GPU every
time we need to know the VRAM size.
We should now fail to load gracefully on detecting no VRAM, rather than
something potentially messy happening.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Previously we were filling it the same as "placements", but in some
cases there're valid alternatives that we were ignoring completely.
Keeping a back-up memory type helps on several low-mem situations.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fixes the !vbo_fifo path in the 3D driver on certain chipsets. Still not
really any good idea of what exactly the magic achieves, but it makes
things work.
While we're at it, in the PCIEGART path, flush on unbinding also.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
There is case where we want to be able to wait only for the
GPU while not waiting for other buffer to be unreserved. This
patch split the no_wait argument all the way down in the whole
ttm path so that upper level can decide on what to wait on or
not.
[airlied: squashed these 4 for bisectability reasons.]
drm/radeon/kms: update to TTM no_wait splitted argument
drm/nouveau: update to TTM no_wait splitted argument
drm/vmwgfx: update to TTM no_wait splitted argument
[vmwgfx patch: Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>]
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Acked-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch is against the drm-fbdevfix1 branch. It removes the
drm_fb_helper_setcolreg function. The reason is that fb_setcolreg is only
used in the case where fb_setcmap is called and no fb_ops->fb_setcmap is
used. In the drm case we always need a fb_setcmap hook to handle multiple
crtcs so we don't need a fb_setcolreg hook. Please apply.
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes
drivers/gpu/drm/ttm/ttm_page_alloc.c: In function 'ttm_page_alloc_debugfs':
drivers/gpu/drm/ttm/ttm_page_alloc.c:829: error: implicit declaration of
function 'seq_printf'
Signed-off-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
a) slow work is always used now for any fbcon hotplug, as its not
a fast task and is more suited to being ran under slow work.
b) attempt to not do any fbdev changes when X is running as we'll
just mess it up. This hooks set_par to hopefully do the changes
once X hands control to fbdev.
This also adds the nouveau/intel hotplug support.
Signed-off-by: Dave Airlie <airlied@redhat.com>
When we are running in a headless environment we have no idea what
output the user might plug in later, we only have hotplug detect
from the digital outputs. So if we detect no connected outputs at
initialisation, start a slow work operation to poll every 5 seconds
for an output.
this is only hooked up for radeon so far, on hw where we have full
hotplug detection there is no need for this.
Signed-off-by: Dave Airlie <airlied@redhat.com>
If we get no outputs setup provide a 1024x768 fbcon, with
this + radeon hotplug stuff I can plug a monitor in after startup
and get to see stuff.
Last thing is to add some sort of timer for non-hpd outputs like
VGA etc.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This breaks the connection between the core drm connector list
and the fbdev connector usage, and allows them to become disjoint
in the future. It also removes the untype void* that was in the
connector struct to support this.
All connectors are added to the fbdev now but this could be
changed in the future.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This move to using the list of crtcs in the fb helper and cleans up the
whole picking code, now we store the crtc/connectors we want directly
into the modeset and we use the modeset directly to set the mode.
Fixes from James Simmons and Ben Skeggs.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The fbdev layer in the kms code should act like a consumer of the kms services and avoid having relying on information being store in the kms core structures in order for it to work.
This patch
a) removes the info pointer/psuedo palette from the core drm_framebuffer structure and moves it to the fbdev helper layer, it also removes the core drm keeping a list of kernel kms fbdevs.
b) migrated all the fb helper functions out of the crtc helper file into the fb helper file.
c) pushed the fb probing/hotplug control into the driver
d) makes the surface sizes into a structure for ease of passing
This changes the intel/radeon/nouveau drivers to use the new helper.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some vbios dac_adj tables are all zeros. Check for that
case and use the default table if so.
Should fix fdo bug 27478.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- make sure legacy dac1 has an enc priv
- remove unused num var
- no need for extra tv_dac var in atom dac functions
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- fix formatting
- clean up tv_dac_cntl handling for tv
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is an unlikely memory leak, but we may as well fix it. It's easy
to fix and every static checker will complain if we don't.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
bad cast was overwriting the tvdac adj values
Fixes fdo bug 27478
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Sysfs interface allows user to configure pool allocator functionality and
change limits for the size of pool.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Using single call to set multiple pages to wc reduces number of expensive cache
flushes.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
ttm_page_pool file is hooked ttm_page_alloc_debugfs for pool
allocator state.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
ttm_page_pool file is hooked ttm_page_alloc_debugfs for pool
allocator state.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
ttm_page_alloc_debugfs can be registered to output the state
of pools.
Debugfs file will output number of pages freed from the pool,
number of pages in pool now and the lowes number of pages in
pool since previous shrink.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On AGP system we might allocate/free routinely uncached or wc memory,
changing page from cached (wb) to uc or wc is very expensive and involves
a lot of flushing. To improve performance this allocator use a pool
of uc,wc pages.
Pools are protected with spinlocks to allow multiple threads to allocate pages
simultanously. Expensive operations are done outside of spinlock to maximize
concurrency.
Pools are linked lists of pages that were recently freed. mm shrink callback
allows kernel to claim back pages when they are required for something else.
Fixes:
* set_pages_array_wb handles highmem pages so we don't have to remove them
from pool.
* Add count parameter to ttm_put_pages to avoid looping in free code.
* Change looping from _safe to normal in pool fill error path.
* Initialize sum variable and make the loop prettier in get_num_unused_pages.
* Moved pages_freed reseting inside the loop in ttm_page_pool_free.
* Add warning comment about spinlock context in ttm_page_pool_free.
Based on Jerome Glisse's and Dave Airlie's pool allocator.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This simplify and improve GPU reset for R1XX-R6XX hw, it's
not 100% reliable here are result:
- R1XX/R2XX works bunch of time in a row, sometimes it
seems it can work indifinitly
- R3XX/R3XX the most unreliable one, sometimes you will be
able to reset few times, sometimes not even once
- R5XX more reliable than previous hw, seems to work most
of the times but once in a while it fails for no obvious
reasons (same status than previous reset just no same
happy ending)
- R6XX/R7XX are lot more reliable with this patch, still
it seems that it can fail after a bunch (reset every
2sec for 3hour bring down the GPU & computer)
This have been tested on various hw, for some odd reasons
i wasn't able to lockup RS480/RS690 (while they use to
love locking up).
Note that on R1XX-R5XX the cursor will disapear after
lockup haven't checked why, switch to console and back
to X will restore cursor.
Next step is to record the bogus command that leaded to
the lockup.
V2 Fix r6xx resume path to avoid reinitializing blit
module, use the gpu_lockup boolean to avoid entering
inifinite waiting loop on fence while reiniting the GPU
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Patch rename gpu_reset to asic_reset in prevision of having
gpu_reset doing more stuff than just basic asic reset.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch cleanup the fence code, it drops the timeout field of
fence as the time to complete each IB is unpredictable and shouldn't
be bound.
The fence cleanup lead to GPU lockup detection improvement, this
patch introduce a callback, allowing to do asic specific test for
lockup detection. In this patch the CP is use as a first indicator
of GPU lockup. If CP doesn't make progress during 1second we assume
we are facing a GPU lockup.
To avoid overhead of testing GPU lockup frequently due to fence
taking time to be signaled we query the lockup callback every
500msec. There is plenty code comment explaining the design & choise
inside the code.
This have been tested mostly on R3XX/R5XX hw, in normal running
destkop (compiz firefox, quake3 running) the lockup callback wasn't
call once (1 hour session). Also tested with forcing GPU lockup and
lockup was reported after the 1s CP activity timeout.
V2 switch to 500ms timeout so GPU lockup get call at least 2 times
in less than 2sec.
V3 store last jiffies in fence struct so on ERESTART, EBUSY we keep
track of how long we already wait for a given fence
V4 make sure we got up to date cp read pointer so we don't have
false positive
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Height in frame size, not field size, and trailed with an 'i'. Matches
the X server behaviour.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Before CVT-R, some monitors would advertise support for an alternative
GTF formula with lower blanking intervals. Correctly identify such
monitors, and use the alternative formula when generating modes for
them.
Note that we only do this for "standard" timing descriptors (tuples of
hsize in characters / aspect ratio / vertical refresh). Range-based
mode lists still only refer to the primary GTF curve. It would be
possible to do better for the latter case, but monitors are required to
support the primary curve over the entire advertised range, so all it
would win you is a lower pixel clock and therefore possibly better image
quality on analog links.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If you have 1920x1200 in both detailed (probably RB) and standard
variants, you probably only want the RB version. But we have no way of
guessing that from standard mode parse. So, if a mode already exists
for a given w/h/r, skip adding it.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Standard timings don't let you say 1366. Both 1360 and 1368 have been
seen in the wild. So invent a CVT timing for it. CVT will round 1366 up
to 1368; we'll then manually underscan it.
Split this into two parts, since we need to do something sneaky between
them in the future.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
1.4 adds better pixel clock precision, explicit reduced blanking
awareness, and extended sync ranges. It's almost like a real spec.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The generic block walk callback looks like overkill, but we'll need it
for other detailed block walks in the future.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In 1.4, the first detailed mode is always the preferred mode. The bit
that used to mean that, now means "this mode is the physical size in
pixels".
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This makes fetching the second EDID block on HDMI monitors actually
work. DDC can't transfer more than 128 bytes at a time. Also,
rearrange the code so the pure DDC bits are separate from block parse.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The GPIO_I2C_INFO table does not always have
ATOM_MAX_SUPPORTED_DEVICE entries. Limit
the number of indices to the size of the
table.
Should fix Novell bug 589022.
v2: fix typo
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Stable <stable@kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
BugLink: http://bugs.launchpad.net/ubuntu/bugs/544671
This system claims to have a LVDS but has not.
Signed-off-by: Stephane Graber <stgraber@ubuntu.com>
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
CC: stable@kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (76 commits)
drm/radeon/kms: enable ACPI powermanagement mode on radeon gpus.
drm/radeon/kms: rs400/480 should set common registers.
drm/radeon/kms: add sanity check to wptr.
drm/radeon/kms/evergreen: get DP working
drm/radeon/kms: add hw_i2c module option
drm/radeon/kms: use new pre/post_xfer i2c bit algo hooks
drm/radeon/kms: disable MSI on IGP chips
drm/radeon/kms: display watermark updates (v2)
drm/radeon/kms/dp: disable training pattern on the sink at the end of link training
drm/radeon/kms: minor fixes for eDP with LCD* device tags (v2)
drm/radeon/kms/dp: remove extraneous training complete call
drm/radeon/kms/atom: minor fixes to transmitter setup
drm/radeon/kms: Only restrict BO to visible VRAM size when pinning to VRAM.
drm: fix build error when SYSRQ is disabled
drm/radeon/kms: fix macbookpro connector quirk
drm/radeon/r6xx/r7xx: further safe reg clean up
drm/radeon: bump the UMS driver version for r6xx/r7xx const buffer support
drm/radeon/kms: bump the version for r6xx/r7xx const buffer support
drm/radeon/r6xx/r7xx: CS parser fixes
drm/radeon/kms: fix some typos in r6xx/r7xx hpd setup
...
Fix up MSI-related conflicts in drivers/gpu/drm/radeon/radeon_irq_kms.c
Some GPUs have an APM/ACPI PM mode selection switch and some BIOSes
set this to APM. We really want this in ACPI mode for Linux.
Signed-off-by: Dave Airlie <airlied@redhat.com>
If we resume in a bad way, we'll get 0xffffffff in wptr, and then
oops with no console. This just adds a sanity check so that we can
avoid the oops and hopefully get more details out of people's systems.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Turn off hw i2c by default except for mm i2c which
is hw only until we sort out the remaining prescale
issues on older chips. hw i2c can be enabled with
hw_i2c=1.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This allows us to remove the internal bit algo bus used by
the radeon i2c algo. We now register a radeon algo adapter
if the gpio line is hw capable and the hw inplementation is
available, otherwise we register a bit algo adapter.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Doesn't seem to work reliably and the pci quirks don't
always work.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Add module option to force the display priority
0 = auto, 1 = normal, 2 = high
- Default to high on r3xx/r4xx/rv515 chips
Fixes flickering problems during heavy acceleration
due to underflow to the display controllers
- Fill in minimal support for RS600
v2 - update display priority when bandwidth is updated
so the user can change the parameter at runtime and it
will take affect on the next modeset.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some systems have LCD* rather than DFP* device tags in the bios
for eDP connectors; notably the new apple iMac. This fixes
things up so eDP connectors with either tag will work.
v2: fix typo
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Looks like a copy/paste typo from when evergreen support
was added.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- 8 lane links are not valid for DP
- remove unused num var
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This prevented radeon.test=1 from testing transfers from/to GTT beyond the
visible VRAM size.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix build error when CONFIG_MAGIC_SYSRQ is not enabled:
drivers/gpu/drm/drm_fb_helper.c:915: error: 'sysrq_drm_fb_helper_restore_op' undeclared (first use in this function)
drivers/gpu/drm/drm_fb_helper.c:929: error: 'sysrq_drm_fb_helper_restore_op' undeclared (first use in this function)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- remove a few more drm only regs
- remove sampler, alu, bool, loop constant regs.
They are set via separate packet3's already
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Drop some more safe regs taht userspace shouldn't hit
- Constant base regs need relocs. This allows us to use
constant buffers rather than the constant register file.
Also we don't want userspace to be able to set arbitrary
mc base values for the const caches.
- Track SQ_CONFIG so we know whether userspace is using
the cfile or constant buffers.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When there is allocation failure in radeon_cs_parser_relocs parser->nrelocs
is not cleaned. This causes NULL pointer defeference in radeon_cs_parser_fini
when clean up code is trying to loop over the relocation array and free the
objects.
Fix adds a check for a possible NULL pointer in clean up code.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
radeon_gart_fini might call GART unbind callback function which
might try to access GART table but if gart_disable is call first
the GART table will be unmapped so any access to it will oops.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We can get this if the user moves the mouse when we are waiting to move
some stuff around in the validate. Don't fail.
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Check that atom cmd and data tables are valid
before using them.
(v2)
- fix some whitespace errors noticed by Rafał Miłecki
- check a few more cases
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- no longer needed with the latest new pll algo fixes.
- also don't use lcd pll limits. They don't seem
to work well for all systems. If we have a case where
they are useful, we can set the flag for that case.
fixes fdo bug 27083
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
I missed rs4xx in 7f1e613daf0fdd0884316ab25a749db3c671329e
Fixes fdo bug 27219.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
RS4xx+ IGP chips use an internal gart, however,
some of them have the agp cap bits set in their pci
configs. Make sure to clear the AGP flag as AGP will
not work with them.
Should fix fdo bug 27225
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
- rs780/880 were using the wrong bandwidth functions
- convert r1xx-r4xx to use the same pm sclk/mclk structs as
r5xx+
- move bandwidth setup to a common function
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
