This preserves the ability to build using older binutils (reportedly <=
2.22).
Fixes: 6becef7ea0 ("powerpc/mpc85xx: Add CPU hotplug support for E6500")
Signed-off-by: Scott Wood <oss@buserror.net>
Cc: chenhui.zhao@freescale.com
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Freescale updates from Scott:
"Highlights include 8xx optimizations, 32-bit checksum optimizations,
86xx consolidation, e5500/e6500 cpu hotplug, more fman and other dt
bits, and minor fixes/cleanup."
Starting with commit <8947e396a829> ("Documentation: dt: mtd:
replace "nor-jedec" binding with "jedec, spi-nor"") we have
"jedec,spi-nor" binding indicating support for JEDEC identification.
Use it for all flashes that are supposed to support READ ID op
according to the datasheets.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@freescale.com>
Signed-off-by: Scott Wood <oss@buserror.net>
This patch adds pcsphy node to FManV3 device tree.
Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Signed-off-by: Scott Wood <oss@buserror.net>
Describe the PHY topology for all configurations supported by each board
Based on prior work by Andy Fleming <afleming@freescale.com>
Signed-off-by: Shruti Kanetkar <Shruti@freescale.com>
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Igal Liberman <Igal.Liberman@freescale.com>
Signed-off-by: Scott Wood <oss@buserror.net>
Avoid duplication of the interrupt-parent, migrate to 4 interrupt-cells
and set the right clock-frequency for pcie (100 Mhz).
Signed-off-by: Alessio Igor Bogani <alessio.bogani@elettra.eu>
Signed-off-by: Scott Wood <oss@buserror.net>
This patch show how defconfigs appear if the kconfig fragment approach is
used.
Signed-off-by: Alessio Igor Bogani <alessio.bogani@elettra.eu>
Signed-off-by: Scott Wood <oss@buserror.net>
Inlining of _dcache_range() functions has shown that the compiler
does the same thing a bit better with one insn less
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
This simplification helps the compiler. We now have only one test
instead of two, so it reduces the number of branches.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
flush/clean/invalidate _dcache_range() functions are all very
similar and are quite short. They are mainly used in __dma_sync()
perf_event locate them in the top 3 consumming functions during
heavy ethernet activity
They are good candidate for inlining, as __dma_sync() does
almost nothing but calling them
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
clear_pages() is never used expect by clear_page, and PPC32 is the
only architecture (still) having this function. Neither PPC64 nor
any other architecture has it.
This patch removes clear_pages() and moves clear_page() function
inline (same as PPC64) as it only is a few isns
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
This patch adds inline functions to use dcbz, dcbi, dcbf, dcbst
from C functions
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
On PPC8xx, flushing instruction cache is performed by writing
in register SPRN_IC_CST. This registers suffers CPU6 ERRATA.
The patch rewrites the fonction in C so that CPU6 ERRATA will
be handled transparently
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
There is no real need to have set_context() in assembly.
Now that we have mtspr() handling CPU6 ERRATA directly, we
can rewrite set_context() in C language for easier maintenance.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
CPU6 ERRATA is now handled directly in mtspr(), so we can use the
standard set_dec() fonction in all cases.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
MPC8xx has an ERRATA on the use of mtspr() for some registers
This patch includes the ERRATA handling directly into mtspr() macro
so that mtspr() users don't need to bother about that errata
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
Add missing SPRN defines into reg_8xx.h
Some of them are defined in mmu-8xx.h, so we include mmu-8xx.h in
reg_8xx.h, for that we remove references to PAGE_SHIFT in mmu-8xx.h
to have it self sufficient, as includers of reg_8xx.h don't all
include asm/page.h
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
ioremap_base is not initialised and is nowhere used so remove it
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
Commit 7711684947 ("[POWERPC] Remove unused machine call outs")
removed the call to setup_io_mappings(), so remove the associated
progress line message
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
x_mapped_by_bats() and x_mapped_by_tlbcam() serve the same kind of
purpose, and are never defined at the same time.
So rename them x_block_mapped() and define them in the relevant
places
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
The fixmap related functions try to map kernel pages that are
already mapped through Large TLBs. pte_offset_kernel() has to
return NULL for LTLBs, otherwise the caller will try to access
level 2 table which doesn't exist
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
Now we have a 8xx specific .c file for that so put it in there
as other powerpc variants do
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
On a live running system (VoIP gateway for Air Trafic Control), over
a 10 minutes period (with 277s idle), we get 87 millions DTLB misses
and approximatly 35 secondes are spent in DTLB handler.
This represents 5.8% of the overall time and even 10.8% of the
non-idle time.
Among those 87 millions DTLB misses, 15% are on user addresses and
85% are on kernel addresses. And within the kernel addresses, 93%
are on addresses from the linear address space and only 7% are on
addresses from the virtual address space.
MPC8xx has no BATs but it has 8Mb page size. This patch implements
mapping of kernel RAM using 8Mb pages, on the same model as what is
done on the 40x.
In 4k pages mode, each PGD entry maps a 4Mb area: we map every two
entries to the same 8Mb physical page. In each second entry, we add
4Mb to the page physical address to ease life of the FixupDAR
routine. This is just ignored by HW.
In 16k pages mode, each PGD entry maps a 64Mb area: each PGD entry
will point to the first page of the area. The DTLB handler adds
the 3 bits from EPN to map the correct page.
With this patch applied, we now get only 13 millions TLB misses
during the 10 minutes period. The idle time has increased to 313s
and the overall time spent in DTLB miss handler is 6.3s, which
represents 1% of the overall time and 2.2% of non-idle time.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
We are spending between 40 and 160 cycles with a mean of 65 cycles in
the DTLB handling routine (measured with mftbl) so make it more
simple althought it adds one instruction.
With this modification, we get three registers available at all time,
which will help with following patch.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
Merge the ftrace changes to support -mprofile-kernel on ppc64le. This is
a prerequisite for live patching, the support for which will be merged
via the livepatch tree based on this topic branch.
The current comment in pmao_restore_workaround() regarding
hard_irq_disable() is wrong. It should say to hard *disable* interrupts
instead of *enable*. Fix it.
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The Physical Core events of the 24x7 PMU can be monitored across various
domains (physical core, vcpu home core, vcpu home node etc). For each of
these core events, we currently create multiple events in sysfs, one for
each domain the event can be monitored in. These events are distinguished
by their suffixes like __PHYS_CORE, __VCPU_HOME_CORE etc.
Rather than creating multiple such entries, we could let the user specify
make 'domain' index a required parameter and let the user specify a value
for it (like they currently specify the core index).
$ cat /sys/bus/event_source/devices/hv_24x7/events/HPM_CCYC
domain=?,offset=0x98,core=?,lpar=0x0
$ perf stat -C 0 -e hv_24x7/HPM_CCYC,domain=2,core=1/ true
(the 'domain=?' and 'core=?' in sysfs tell perf tool to enforce them as
required parameters).
This simplifies the interface and allows users to identify events by the
name specified in the catalog (User can determine the domain index by
referring to '/sys/bus/event_source/devices/hv_24x7/interface/domains').
Eliminating the event suffix eliminates several functions and simplifies
code.
Note that Physical Chip events can only be monitored in the chip domain
so those events have the domain set to 1 (rather than =?) and users don't
need to specify the domain index for the Chip events.
$ cat /sys/bus/event_source/devices/hv_24x7/events/PM_XLINK_CYCLES
domain=1,offset=0x230,chip=?,lpar=0x0
$ perf stat -C 0 -e hv_24x7/PM_XLINK_CYCLES,chip=1/ true
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
To help users determine domains, display the domain indices used by the
kernel in sysfs.
$ cat /sys/bus/event_source/devices/hv_24x7/interface/domains
1: Physical Chip
2: Physical Core
3: VCPU Home Core
4: VCPU Home Chip
5: VCPU Home Node
6: VCPU Remote Node
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
For 24x7 counters, perf displays the raw value of the 24x7 counter, which
is a monotonically increasing value.
perf stat -C 0 -e \
'hv_24x7/HPM_0THRD_NON_IDLE_CCYC__PHYS_CORE,core=1/' \
sleep 1
Performance counter stats for 'CPU(s) 0':
9,105,403,170 hv_24x7/HPM_0THRD_NON_IDLE_CCYC__PHYS_CORE,core=1/
0.000425751 seconds time elapsed
In the typical usage of 'perf stat' this counter value is not as useful
as the _change_ in the counter value over the duration of the application.
Have h_24x7_event_init() set the event's prev_count to the raw value of
the 24x7 counter at the time of initialization. When the application
terminates, hv_24x7_event_read() will compute the change in value and
report to the perf tool. Similarly, for the transaction interface, clear
the event count to 0 at the beginning of the transaction.
perf stat -C 0 -e \
'hv_24x7/HPM_0THRD_NON_IDLE_CCYC__PHYS_CORE,core=1/' \
sleep 1
Performance counter stats for 'CPU(s) 0':
245,758 hv_24x7/HPM_0THRD_NON_IDLE_CCYC__PHYS_CORE,core=1/
1.006366383 seconds time elapsed
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
24x7 counters can belong to different domains (core, chip, virtual CPU
etc). For events in the 'chip' domain, sysfs entry currently looks like:
$ cd /sys/bus/event_source/devices/hv_24x7/events
$ cat PM_XLINK_CYCLES__PHYS_CHIP
domain=0x1,offset=0x230,core=?,lpar=0x0
where the required parameter, 'core=?' is specified with perf as:
perf stat -C 0 -e hv_24x7/PM_XLINK_CYCLES__PHYS_CHIP,core=1/ \
/bin/true
This is inconsistent in that 'core' is a required parameter for a chip
event. Instead, have the the sysfs entry display 'chip=?' for chip
events:
$ cd /sys/bus/event_source/devices/hv_24x7/events
$ cat PM_XLINK_CYCLES__PHYS_CHIP
domain=0x1,offset=0x230,chip=?,lpar=0x0
We also need to add a 'chip' entry in the sysfs format directory:
$ ls /sys/bus/event_source/devices/hv_24x7/format
chip core domain lpar offset vcpu
^^^^
(new)
so the perf tool can automatically check usage and format the chip
parameter correctly:
$ perf stat -C 0 -v -e hv_24x7/PM_XLINK_CYCLES__PHYS_CHIP/ \
/bin/true
Required parameter 'chip' not specified
invalid or unsupported event: 'hv_24x7/PM_XLINK_CYCLES__PHYS_CHIP/'
$ perf stat -C 0 -v -e hv_24x7/PM_XLINK_CYCLES__PHYS_CHIP,chip=1/ \
/bin/true
hv_24x7/PM_XLINK_CYCLES__PHYS_CHIP,chip=1/: 0 6628908 6628908
Performance counter stats for 'CPU(s) 0':
0 hv_24x7/PM_XLINK_CYCLES__PHYS_CHIP,chip=1/
0.006606970 seconds time elapsed
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Power8 supports a large number of events in each susbystem so when a
user runs:
perf stat -e branch-instructions sleep 1
perf stat -e L1-dcache-loads sleep 1
it is not clear as to which PMU events were monitored.
Export the generic hardware and cache perf events for Power8 to sysfs,
so users can precisely determine the PMU event monitored by the generic
event.
Eg:
cat /sys/bus/event_source/devices/cpu/events/branch-instructions
event=0x10068
$ cat /sys/bus/event_source/devices/cpu/events/L1-dcache-loads
event=0x100ee
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We used the PME_ prefix earlier to avoid some macro/variable name
collisions. We have since changed the way we define/use the event
macros so we no longer need the prefix.
By dropping the prefix, we keep the the event macros consistent with
their official names.
Reported-by: Michael Ellerman <ellerman@au1.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
add the missing RAID Engine device node for p5040.
otherwise, the device can not be detected.
Signed-off-by: Xuelin Shi <xuelin.shi@nxp.com>
Signed-off-by: Scott Wood <oss@buserror.net>
csum_partial is often called for small fixed length packets
for which it is suboptimal to use the generic csum_partial()
function.
For instance, in my configuration, I got:
* One place calling it with constant len 4
* Seven places calling it with constant len 8
* Three places calling it with constant len 14
* One place calling it with constant len 20
* One place calling it with constant len 24
* One place calling it with constant len 32
This patch renames csum_partial() to __csum_partial() and
implements csum_partial() as a wrapper inline function which
* uses csum_add() for small 16bits multiple constant length
* uses ip_fast_csum() for other 32bits multiple constant
* uses __csum_partial() in all other cases
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
Modify platform driver suspend/resume to syscore
suspend/resume. This is because p1022ds needs to use
localbus when entering the PCIE resume.
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
[scottwood: dropped makefile churn]
Signed-off-by: Scott Wood <oss@buserror.net>
When CONFIG_DEBUG_PAGEALLOC is activated, the initial TLB mapping gets
flushed to track accesses to wrong areas. Therefore, kernel addresses
will also generate ITLB misses.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
The MPC885 reference manual says that SDCR shall have value 0x40, but
most exemples set SDCR to 0x1
With 0x1 in SDCR, we observe TX underruns on SCC when using it in
QMC mode.
According the NXP technical support, this is a copy/paste error from
MPC860 reference manual, 0x40 being the only value supported
by the MPC885 HW.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>
This patch disables deprecated IDE subsystem in mpc8610_hpcd_defconfig
(no IDE host drivers are selected in this config so there is no valid
reason to enable IDE subsystem itself).
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Scott Wood <oss@buserror.net>
This patch disables deprecated IDE subsystem in stx_gp3_defconfig
(no IDE host drivers are selected in this config so there is no valid
reason to enable IDE subsystem itself).
Cc: Scott Wood <oss@buserror.net>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Scott Wood <oss@buserror.net>
This patch disables deprecated IDE subsystem in ksi8560_defconfig
(no IDE host drivers are selected in this config so there is no valid
reason to enable IDE subsystem itself).
Cc: Scott Wood <oss@buserror.net>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Scott Wood <oss@buserror.net>
This patch disables deprecated IDE subsystem in mpc834x_itx_defconfig
(no IDE host drivers are selected in this config so there is no valid
reason to enable IDE subsystem itself).
Cc: Scott Wood <oss@buserror.net>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Scott Wood <oss@buserror.net>
The hcalls introduced for cxl use a possible new value:
H_STATE (invalid state).
Co-authored-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Reviewed-by: Manoj Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In eeh_pci_enable(), after making the request to set the new options, we
call eeh_ops->wait_state() to check that the request finished successfully.
At the moment, if eeh_ops->wait_state() returns 0, we return 0 without
checking that it reflects the expected outcome. This can lead to callers
further up the chain incorrectly assuming the slot has been successfully
unfrozen and continuing to attempt recovery.
On powernv, this will occur if pnv_eeh_get_pe_state() or
pnv_eeh_get_phb_state() return 0, which in turn occurs if the relevant OPAL
call returns OPAL_EEH_STOPPED_MMIO_DMA_FREEZE or
OPAL_EEH_PHB_ERROR respectively.
On pseries, this will occur if pseries_eeh_get_state() returns 0, which in
turn occurs if RTAS reports that the PE is in the MMIO Stopped and DMA
Stopped states.
Obviously, none of these cases represent a successful completion of a
request to thaw MMIO or DMA.
Fix the check so that a wait_state() return value of 0 won't be considered
successful for the EEH_OPT_THAW_MMIO or EEH_OPT_THAW_DMA cases.
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
