Currently we are always using the Emulex OUI for a VF MAC address
while generating MAC for a VF. Use OUI from current MAC instead.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PF needs to cleanup all the interface handles that it created for the VFs.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to avoid the completion processing for be_vf_eth_addr_config
to consume the link status notification before netdev_register.
Otherwise this causes the PF miss its first link status update.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While configuring QOS for VFs, the VF number should be translated
to domain number correctly.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The atl1 driver uses the legacy PCI power management, so it has to
do some PCI-specific things in its ->suspend() and ->resume()
callbacks, which isn't necessary and should better be done by the PCI
subsystem-level power management code.
Convert atl1 to the new PCI power management framework and make it
let the PCI subsystem take care of all the PCI-specific aspects of
device handling during system power transitions.
Tested-by: Thomas Fjellstrom <thomas@fjellstrom.ca>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The atl1c driver shouldn't call device_init_wakeup() in its probe
routine with the second argument equal to 1, because for PCI devices
the wakeup capability setting is initialized as appropriate by the
PCI subsystem. Remove the potentially harmful call.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tg3 driver uses device_init_wakeup() in such a way that the
device's power.can_wakeup flag may be set even though the PCI
subsystem cleared it before, in which case the device cannot wake
up the system from sleep states. Modify the driver to only change
the power.can_wakeup flag if the device is not capable of generating
wakeup signals.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current driver does not show 100MB support in ethtool.
Adding support for the same.
Signed-off-by: Atita Shirwaikar <atita.shirwaikar@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function ixgbe_init_mbx_params_pf isn't used unless CONFIG_PCI_IOV
is defined. This is causing namespace warnings. So I wrapped its
definition in CONFIG_PCI_IOV too.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We had a support function that just walked a few pointers to get
from the ixgbe_hw struct to the netdev pointer. This was causing
a namespace warning so I removed it and just reference the pointers
directly.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We didn't need the prototype and it was causing namespace complaints so
I made it static.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This consolidates hardware specifics to ixgbe_dcb.c this simplifies
code that was previously branching based on hardware type.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This removes the RESET bit previously used to force a device
reset when DCB bandwidth configurations were changed. This can
now be done dynamically without a reset so the bit is no longer
needed. The only remaining operations that force a device reset
are DCB enable/disable and FCoE application priority changes.
DCB enable/disable is a hardware requirement.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The 82599 and 82598 devices do not require hardware resets to
configure CEE pg settings. This patch changes DCB configuration
to set the CEE pg values directly from the dcbnl ops routine.
This reduces the number of resets seen on the wire and allows
LLDP to reach a steady state faster.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implements 802.1Qaz support for ixgbe driver. Additionally,
this adds IEEE_8021QAZ_TSA_{} defines to dcbnl.h this is to
avoid having to use cryptic numeric codes for the TSA type.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the routines that configure the HW for DCB require a
ixgbe_dcb_config structure. This structure was designed to support
the CEE standard and does not match the IEEE standard well.
This patch changes the HW routines in ixgbe_dcb_8259x.{ch} to use
raw pfc and bandwidth values. This requires some parsing of the DCB
configuration but makes the HW routines independent of the data
structure that contains the DCB configuration.
The primary advantage to doing this is we can do HW setup directly
from the 802.1Qaz ops without having to arbitrarily encapsulate this
data into the CEE structure.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove round robin configuration code for 82598 parts it
is not settable and is always false.
If we need/want this in the future we can add it back properly.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the FCoE priority is not changing do not set the RESET and
APP_UPCHG bits. This causes unneeded HW resets and which can
cause unneeded LLDP frames and negotiations.
The current check is not sufficient because the FCoE priority
can change twice during a negotiation which results in the
bits being set. This occurs when the switch changes the
priority or when the link is reset with switches that do not
include the APP priority until after PFC has been negotiated.
This results in set_app being called with the local APP
priority. Then the negotiation completes and set_app
is called again with the peer APP priority. The check
fails so the device is reset and the above occurs again
resulting in an endless loop of resets.
By only resetting the device if the APP priority has really
changed we short circuit the loop.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds full support for SR-IOV by enabling the PF side.
VF side has already been committed.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
...when invoked while interface is not up or when auto-negotiation is
disabled as done by other drivers.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
*e1000_gstrings_test is not the same size as e1000_gstrings_test.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As a precautionary measure, expand the fix submitted in commit
4d163b75e9 entitled "tg3: Fix 5719 A0 tx
completion bug" to apply to all 5719 revisions.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we didn't have a routing cache, we would not be able to properly
propagate certain kinds of dynamic path attributes, for example
PMTU information and redirects.
The reason is that if we didn't have a routing cache, then there would
be no way to lookup all of the active cached routes hanging off of
sockets, tunnels, IPSEC bundles, etc.
Consider the case where we created a cached route, but no inetpeer
entry existed and also we were not asked to pre-COW the route metrics
and therefore did not force the creation a new inetpeer entry.
If we later get a PMTU message, or a redirect, and store this
information in a new inetpeer entry, there is no way to teach that
cached route about the newly existing inetpeer entry.
The facilities implemented here handle this problem.
First we create a generation ID. When we create a cached route of any
kind, we remember the generation ID at the time of attachment. Any
time we force-create an inetpeer entry in response to new path
information, we bump that generation ID.
The dst_ops->check() callback is where the knowledge of this event
is propagated. If the global generation ID does not equal the one
stored in the cached route, and the cached route has not attached
to an inetpeer yet, we look it up and attach if one is found. Now
that we've updated the cached route's information, we update the
route's generation ID too.
This clears the way for implementing PMTU and redirects directly in
the inetpeer cache. There is absolutely no need to consult cached
route information in order to maintain this information.
At this point nothing bumps the inetpeer genids, that comes in the
later changes which handle PMTUs and redirects using inetpeers.
Signed-off-by: David S. Miller <davem@davemloft.net>
Validity of the cached PMTU information is indicated by it's
expiration value being non-zero, just as per dst->expires.
The scheme we will use is that we will remember the pre-ICMP value
held in the metrics or route entry, and then at expiration time
we will restore that value.
In this way PMTU expiration does not kill off the cached route as is
done currently.
Redirect information is permanent, or at least until another redirect
is received.
Signed-off-by: David S. Miller <davem@davemloft.net>
Future changes will add caching information, and some of
these new elements will be addresses.
Since the family is implicit via the ->daddr.family member,
replicating the family in ever address we store is entirely
redundant.
Signed-off-by: David S. Miller <davem@davemloft.net>
commit a512b92 adds sysfs entry for net device group, but
before this commit, tun also uses group sysfs, so after this
commit checkin, kernel warns like this:
sysfs: cannot create duplicate filename '/devices/virtual/net/vnet0/group'
Since tun has used this for years, rename sysfs under tun might
break existing userspace, so rename group sysfs entry for net device
group is a better choice.
Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, in case reload pch_can,
pch_can not to be able to catch interrupt.
The cause is bus-master is not set in pch_can.
Thus, add enabling bus-master processing.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when rmmod pch_can, kernel failure occurs.
The cause is pci_iounmap executed before pch_can_reset.
Thus pci_iounmap moves after pch_can_reset.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, 800k comms fails since prop_seg set zero.
(EG20T PCH CAN register of prop_seg must be set more than 1)
To prevent prop_seg set to zero, change tseg2_min 1 to 2.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit aa94210411 ("net: init ingress
queue") we moved the allocation and lock initialization of the queues
into alloc_netdev_mq() since register_netdevice() is way too late.
The problem is that dev->type is not setup until the setup()
callback is invoked by alloc_netdev_mq(), and the dev->type is
what determines the lockdep class to use for the locks in the
queues.
Fix this by doing the queue allocation after the setup() callback
runs.
This is safe because the setup() callback is not allowed to make any
state changes that need to be undone on error (memory allocations,
etc.). It may, however, make state changes that are undone by
free_netdev() (such as netif_napi_add(), which is done by the
ipoib driver's setup routine).
The previous code also leaked a reference to the &init_net namespace
object on RX/TX queue allocation failures.
Signed-off-by: David S. Miller <davem@davemloft.net>
rtnl_link_ops->setup(), and the "setup" callback passed to alloc_netdev*(),
cannot make state changes which need to be undone on failure. There is
no cleanup mechanism available at this point.
So we have to add the caif private instance to the global list once we
are sure that register_netdev() has succedded in ->newlink().
Otherwise, if register_netdev() fails, the caller will invoke free_netdev()
and we will have a reference to freed up memory on the chnl_net_list.
Signed-off-by: David S. Miller <davem@davemloft.net>
The Linux IPv4 AH stack aligns the AH header on a 64 bit boundary
(like in IPv6). This is not RFC compliant (see RFC4302, Section
3.3.3.2.1), it should be aligned on 32 bits.
For most of the authentication algorithms, the ICV size is 96 bits.
The AH header alignment on 32 or 64 bits gives the same results.
However for SHA-256-128 for instance, the wrong 64 bit alignment results
in adding useless padding in IPv4 AH, which is forbidden by the RFC.
To avoid breaking backward compatibility, we use a new flag
(XFRM_STATE_ALIGN4) do change original behavior.
Initial patch from Dang Hongwu <hongwu.dang@6wind.com> and
Christophe Gouault <christophe.gouault@6wind.com>.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Specification links:
- CDC NCM errata link:
http://www.usb.org/developers/devclass_docs/NCM10_012011.zip
- CDC and WMC errata link:
http://www.usb.org/developers/devclass_docs/CDC1.2_WMC1.1_012011.zip
Changes:
- driver updated to match cdc.h header with errata changes
- added support for USB_CDC_SET_NTB_INPUT_SIZE control request with
8 byte length
- fixes to comply with specification: send only control requests supported by
device, set number of datagrams for IN direction, connection speed structure
update, etc.
- packet loss fixed for tx direction; misleading flag renamed.
- adjusted hard_mtu value.
Signed-off-by: Alexey Orishko <alexey.orishko@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will synchronize the version string with that of the latest source
forge driver which shares its functionality.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe_fcoe_ddp_get function wasn't initializing one of its variables
and this was producing compiler warnings. This patch cleans that up.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change fixes VM pool allocation issues based on MAC address filtering,
as well as limits the scope of VF access to promiscuous mode.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We have found a hardware erratum on 82599 hardware that can lead to
unpredictable behavior when Header Splitting mode is enabled. So
we are no longer enabling this feature on affected hardware.
Please see the 82599 Specification Update for more information.
CC: stable@kernel.org
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
