For Haswell and Broadwell, if the display power well has been disabled,
the display audio controller divider values EM4 M VALUE and EM5 N VALUE
will have been lost. The CDCLK frequency is required for reprogramming them
to generate 24MHz HD-A link BCLK. So provide a private interface for the
audio driver to query CDCLK.
This is a stopgap solution until a more generic interface between audio
and display drivers has been implemented.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit "drm/vmwgfx: correct fb_fix_screeninfo.line_length", while fixing a
vmwgfx fbdev bug, also writes the pitch to a supposedly read-only register:
SVGA_REG_BYTES_PER_LINE, while it should be (and also in fact is) written to
SVGA_REG_PITCHLOCK.
This patch is Cc'd stable because of the unknown effects writing to this
register might have, particularly on older device versions.
v2: Updated log message.
Cc: stable@vger.kernel.org
Cc: Christopher Friedt <chrisfriedt@gmail.com>
Tested-by: Christopher Friedt <chrisfriedt@gmail.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
The GEN FBC unit provides the ability to set a low pass on frames it
attempts to compress. If a frame is less than a certain amount
compressibility (2:1, 4:1) it will not bother. This allows the driver to
reduce the size it requests out of stolen memory.
Unluckily, a few months ago, Ville actually began using this feature for
framebuffers that are 16bpp (not sure why not 8bpp). In those cases, we
are already using this mechanism for a different purpose, and so we can
only achieve one further level of compression (2:1 -> 4:1)
FBC GEN1, ie. pre-G45 is ignored.
The cleverness of the patch is Art's. The bugs are mine.
v2: Update message and including missing threshold case 3 (Spotted by Arthur).
Cc: Art Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Right now, there is no threshold (0 means fail, 1 means 1:1 compression
limit). This is to split the function/non-functional change of the next
patch.
The next patch will start to attempt to reduce the amount of CFB space
we need for dire situations. It will be contained within this function.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We are already using the size to determine whether or not to free the
object, so there is no functional change there. Almost everything else
has changed to static allocations of the drm_mm_node too.
Aside from bringing this inline with much of our other code, this makes
error paths slightly simpler, which benefits the look of an upcoming
patch.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
misc fixes, output fixes for 4k monitor, dpm lockup fixes
* 'drm-fixes-3.16' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: page table BOs are kernel allocations
drm/radeon/cik: fix typo in EOP packet
drm/radeon: Track the status of a page flip more explicitly
drm/radeon/dpm: fix vddci setup typo on cayman
drm/radeon/dpm: fix typo in vddci setup for eg/btc
drm/radeon: use RADEON_MAX_CRTCS, RADEON_MAX_AFMT_BLOCKS (v2)
drm/radeon: Use only one line for whole DPCD debug output
drm/radeon: add a module parameter to control deep color support
drm/radeon: enable bapm by default on desktop TN/RL boards
drm/radeon: enable bapm by default on KV/KB
drm/radeon: only apply bapm changes for AC power on ARUBA
drm/radeon: adjust default dispclk on DCE6 (v2)
Userspace shouldn't be able to access them.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Volatile bit was in the wrong location. This bit is
not used at the moment.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
use mm.h definition
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Higher RC6 residency is observed using timeout mode
instead of EI mode. This applies to Broadwell only.
The difference is particularly noticeable with video
playback.
Signed-off-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This prevents a panic: radeon_crtc_handle_page_flip() could run before
radeon_flip_work_func(), triggering the BUG_ON() in drm_vblank_put().
Tested-by: Dieter Nützel <Dieter@nuetzel-hh.de>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some monitors seem to have problems with deep color enabled, even
though they claim to support it. I'm not sure if the monitor
need a quirk or if the driver is doing something the monitor doesn't
like. At this point lets just disable deep color by default like
we did for hdmi audio and work through the bugs so we can eventually
enable it by default.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=80531
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
bapm enabled the GPU and CPU to share TDP headroom. It was
disabled by default since some laptops hung when it was enabled
in conjunction with dpm. It seems to be stable on desktop
boards and fixes hangs on boot with dpm enabled on certain
boards, so enable it by default on desktop boards.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=72921
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
bapm allows the GPU and CPU to share TDP. This allows
for additional performance out of the GPU and CPU when
the headroom is available.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Set the default to 600Mhz if it's not set in the bios,
and bump the default to 600Mhz if it's lower than that.
This fixes display issues with certain 4k DP monitors when
using 5.4 Ghz DP clocks.
v2: fix typo.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It is possible that, by the time we run i915_drm_freeze(),
delayed_resume_work was already queued but did not run yet. If it
still didn't run after intel_runtime_pm_disable_interrupts(), by the
time it runs it will try to change the interrupt registers with the
interrupts already disabled, which will trigger a WARN. We can
reliably reproduce this with the pm_rpm system-suspend test case.
In order to avoid the problem, we have to flush the work before
disabling the interrupts. We could also cancel the work instead of
flushing it, but that would require us to put a runtime PM reference -
and any other resource we may need in the future - in case the work
was already queued, so I believe flushing the work is more
future-proof, although less efficient. But I can also change this part
if someone requests.
Another thing I tried was to move the intel_suspend_gt_powersave()
call to before intel_runtime_pm_disable_interrupts(), but since that
function needs to be called after the interrupts are already disabled,
due to dev_priv->rps.work, this strategy didn't work.
Testcase: igt/pm_rpm/system-suspend
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80517
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Drop WA to fix Voltage not getting dropped to Vmin when Gfx is power
gated for latest VLV revision.
Workaround fixed in Latest VLV revision. Forcing Gfx clk up not needed,
and Requesting the min freq should bring bring the voltage Vnn.
v2: Drop WA for Latest VLV revision (Ville)
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[Jani: modified code comment, reformatted the commit message a bit.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Apparently we can't trust this field on other platforms and need to find
some other way.
This fixes a regression introduced in
commit 27da3bdfcf
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Fri Apr 4 16:12:07 2014 -0700
drm/i915: use VBT to determine whether to enumerate the VGA port
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
BDW signals the flip done interrupt immediately after the DSPSURF write
when the plane is disabled. This is true even if we've already armed
DSPCNTR to enable the plane at the next vblank. This causes major
problems for our page flip code which relies on the flip done interrupts
happening at vblank time.
So what happens is that we enable the plane, and immediately allow
userspace to submit a page flip. If the plane is still in the process
of being enabled when the page flip is issued, the flip done gets
signalled immediately. Our DSPSURFLIVE check catches this to prevent
premature flip completion, but it also means that we don't get a flip
done interrupt when the plane actually gets enabled, and so the page
flip is never completed.
Work around this by re-introducing blocking vblank waits on BDW
whenever we enable the primary plane.
I removed some of the vblank waits here:
commit 6304cd91e7
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri Apr 25 13:30:12 2014 +0300
drm/i915: Drop the excessive vblank waits from modeset codepaths
To avoid these blocking vblank waits we should start using the vblank
interrupt instead of the flip done interrupt to complete page flips.
But that's material for another patch.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79354
Tested-by: Guo Jinxian <jinxianx.guo@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Fixes for 3.16-rc2; regressions, races, and warns; Broadwell PCI IDs.
* tag 'drm-intel-fixes-2014-06-26' of git://anongit.freedesktop.org/drm-intel:
drm/i915: vlv_prepare_pll is only needed in case of non DSI interfaces
drm/i915: Hold the table lock whilst walking the file's idr and counting the objects in debugfs
drm/i915: BDW: Adding Reserved PCI IDs.
drm/i915: Only mark the ctx as initialised after a SET_CONTEXT operation
drm/i915: default to having backlight if VBT not available
drm/i915: cache hw power well enabled state
The TDA998x can't handle modes with clocks above 150MHz, or resolutions
larger than 8192x2048.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
One of Jean-Francois patches changed the EDID polling to once every
10ms for 10 interations, whereas the original code did 1ms for 100
interations. This appears to cause boot-time detection to take
noticably longer. Revert this change.
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently tda998x_encoder_destroy() calls cec_write() and reg_clear(),
as part of the release procedure. Such calls need to access the I2C bus
and therefore, we need to call them before drm_i2c_encoder_destroy()
which unregisters the I2C device.
This commit moves the latter so it's done afterwards.
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Signed-off-by: Ezequiel García <ezequiel@vanguardiasur.com.ar>
Cc: <stable@vger.kernel.org> #v3.9+
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
crtc->primary->fb may be NULL upon entry to intel_pipe_set_base() if the
primary plane has previously been disabled via the universal plane
interface. We need to check for NULL before trying to reference
old_fb's obj.
This fixes a regression introduced in
commit a071fa0064
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Jun 18 23:28:09 2014 +0200
drm/i915: Introduce accurate frontbuffer tracking
Testcase: igt/kms_universal_plane
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
For MIPI, DSI PLL is configured separately in vlv_configure_dsi_pll
during the DSI enable sequence
Causing WARN dump otherwise in dpio_reads
v2: Add IS_CHERRYVIEW check as suggested by Ville
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This pull-request fixes hdmi power-off order issue, mixer issues
related to power on/off, and includes trivial fixups.
* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: enable vsync interrupt while waiting for vblank
drm/exynos: soft reset mixer before reconfigure after power-on
drm/exynos: allow multiple layer updates per vsync for mixer
drm/exynos: stop mixer before gating clocks during poweroff
drm/exynos: set power state variable after enabling clocks and power
drm/exynos: disable unused windows on apply
drm/exynos: Fix de-registration ordering
drm/exynos: change zero to NULL for sparse
drm/exynos: dpi: Fix NULL pointer dereference with legacy bindings
drm/exynos: hdmi: fix power order issue
A handful of fixes from various folks.
* 'msm-fixes-3.16' of git://people.freedesktop.org/~robclark/linux:
drm/msm: fix IOMMU cleanup for -EPROBE_DEFER
drm/msm: use PAGE_ALIGNED instead of IS_ALIGNED(PAGE_SIZE)
drm/msm/hdmi: set hdp clock rate before prepare_enable
drm/msm: storage class should be before const qualifier
drm/msm: Replace type of paddr to uint32_t.
If user uses wrong ioctl command with _IOC_NONE and argument size
greater than 0, it can cause NULL pointer access from memset of line
463. If _IOC_NONE, don't memset to 0 for kdata.
Signed-off-by: Zhaowei Yuan <zhaowei.yuan@samsung.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
mixer_wait_for_vblank function expects that the upcoming
vsync interrupt handler routine will clear the
wait_vsync_event atomic variable.
For this to happen, interrupts should be enabled and
disabled properly.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Mixer soft reset is a recommended step before reconfiguring
the mixer after power on. Mixer looses the previous state of
DMAs if soft reset. This is the recommendation from the
hardware team.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Allowing only one layer update per vsync can cause issues
while there are update available for both layers. There is
a good amount of possibility to loose updates if we allow
single update per vsync.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Fallout from
commit 46470fc932
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date: Wed May 21 19:01:06 2014 +0300
drm/i915: Add null state batch to active list
undid the earlier fix of only marking the ctx as initialised after it is
saved by the hardware during a SET_CONTEXT operation:
commit ad1d219974
Author: Ben Widawsky <benjamin.widawsky@intel.com>
Date: Sat Dec 28 13:31:49 2013 -0800
drm/i915: set ctx->initialized only after RCS
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[Jani: add reference to the earlier fix in the commit messsage.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Mixer should be power gated only after it is gracefully stopped.
The recommended sequence is to Stop the mixer and wait till
it enters to IDLE state before gating the clocks and power to
the mixer.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Power state variable holds the state of the mixer device.
Power on and power off functions are toggling these variable
at wrong place.
State variable should be changed to true only after Runtime
PM and clocks are enabled. Else it may result to a situation
where mixer registers are accessed with device power enabled.
Similar logic for poweroff sequence.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The patch disables non-enabled HW windows on applying
configuration, it will allow to clear windows enabled
by bootloader.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
'exynos_drm_pdev' was not getting unregistered if platform_driver_register()
failed. Fix the ordering to allow this. This also fixes the below warning by
moving the #endif macro. While at it also fix the ordering in the exit function
so that de-registration happens in opposite order of registration.
drivers/gpu/drm/exynos/exynos_drm_drv.c:768:1: warning: label
'err_unregister_pd' defined but not used [-Wunused-label]
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
We recently changed this function to return a pointer instead of an int
so we need to change this zero to a NULL or Sparse complains:
drivers/gpu/drm/exynos/exynos_drm_drv.h:346:47:
warning: Using plain integer as NULL pointer
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
If there is no panel node in DT and instead display timings are provided
directly in FIMD node, there is no panel object created and ctx->panel
becomes NULL. However during Exynos DRM initialization
drm_helper_hpd_irq_event() is called, which in turns calls
exynos_dpi_detect(), which dereferences ctx->panel without a check,
causing a NULL pointer derefrence.
This patch fixes the issue by adding necessary NULL pointer check.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch resolves page fault issue of Mixer when disabled.
The SFRs of VP and Mixer are updated by Vertical Sync of Timing
generator which is a part of HDMI so the sequence to disable TV
Subsystem should be as following:
VP -> Mixer -> HDMI
For this, this patch disables Mixer and VP (if used) prior to
disabling HDMI.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Apparently there are Apple laptops with magic smoke for a VBIOS, which
we fail to find and use. Default to having and setting up backlight in
this case.
This fixes a regression introduced by
commit c675949ec5
Author: Jani Nikula <jani.nikula@intel.com>
Date: Wed Apr 9 11:31:37 2014 +0300
drm/i915: do not setup backlight if not available according to VBT
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=77831
Reported-and-tested-by: Matteo Cypriani <mcy@lm7.fr>
Cc: stable@vger.kernel.org # 3.15+
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Jesse noticed that the punit communication needed to query the VLV power
well status can cause substantial delays. Since we can query the state
frequently, for example during I2C transfers, maintain a cached version
of the HW state to get rid of this delay.
This fixes at least one reported regression where boot time increased by
~4 seconds due to frequent power well state queries on VLV during eDP
EDID read.
This regression has been introduced in
commit bb4932c4f1
Author: Imre Deak <imre.deak@intel.com>
Date: Mon Apr 14 20:24:33 2014 +0300
drm/i915: vlv: check port power domain instead of only D0 for eDP VDD on
Reported-by: Jesse Barnes <jesse.barnes@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If probe fails after IOMMU is attached, we need to detach in order to
clean up properly. Before this change, IOMMU faults would occur if the
probe failed (-EPROBE_DEFER).
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
use mm.h definition
Cc: David Airlie <airlied@linux.ie>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The clock driver usually complains when a clock is being prepared
before setting its rate. It is the case here for "core_clk" which
needs to be set at 19.2 MHz before we attempt a prepare_enable().
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Rob Clark <robdclark@gmail.com>
This patch helps to avoid the following build issue:
drivers/gpu/drm/msm/msm_fbdev.c:108:2: error: passing argument 3 of 'msm_gem_get_iova_locked' from incompatible pointer type [-Werror]
msm_gem_get_iova_locked(fbdev->bo, 0, &paddr);
^
In file included from drivers/gpu/drm/msm/msm_fbdev.c:18:0:
drivers/gpu/drm/msm/msm_drv.h:153:5: note: expected 'uint32_t *' but argument is of type 'dma_addr_t *'
int msm_gem_get_iova_locked(struct drm_gem_object *obj, int id,
^
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The significant part here is a few security fixes for ALSA core
control API by Lars. Besides that, there are a few fixes for ASoC
sigmadsp (again by Lars) for building properly, and small fixes for
ASoC rsnd, MMP, PXA and FSL, in addition to a fix for bogus WARNING in
i915/HD-audio binding.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=dWKL
-----END PGP SIGNATURE-----
Merge tag 'sound-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"The significant part here is a few security fixes for ALSA core
control API by Lars. Besides that, there are a few fixes for ASoC
sigmadsp (again by Lars) for building properly, and small fixes for
ASoC rsnd, MMP, PXA and FSL, in addition to a fix for bogus WARNING in
i915/HD-audio binding"
* tag 'sound-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: control: Make sure that id->index does not overflow
ALSA: control: Handle numid overflow
ALSA: control: Don't access controls outside of protected regions
ALSA: control: Fix replacing user controls
ALSA: control: Protect user controls against concurrent access
drm/i915, HD-audio: Don't continue probing when nomodeset is given
ASoC: fsl: Fix build problem
ASoC: rsnd: fixup index of src/dst mod when capture
ASoC: fsl_spdif: Fix integer overflow when calculating divisors
ASoC: fsl_spdif: Fix incorrect usage of regmap_read()
ASoC: dapm: Make sure register value is in sync with DAPM kcontrol state
ASoC: sigmadsp: Split regmap and I2C support into separate modules
ASoC: MMP audio needs sram support
ASoC: pxa: add I2C dependencies as needed
This commit add check for return value of init_ring_common() in the
init_render_ring(). Now, when failure is detected the error code is
propagated to the caller instead of being ignored.
Signed-off-by: Konrad Zapalowicz <bergo.torino@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So these are the guts of the new beast. This tracks when a frontbuffer
gets invalidated (due to frontbuffer rendering) and hence should be
constantly scaned out, and when it's flushed again and can be
compressed/one-shot-upload.
Rules for flushing are simple: The frontbuffer needs one more full
upload starting from the next vblank. Which means that the flushing
can _only_ be called once the frontbuffer update has been latched.
But this poses a problem for pageflips: We can't just delay the
flushing until the pageflip is latched, since that would pose the risk
that we override frontbuffer rendering that has been scheduled
in-between the pageflip ioctl and the actual latching.
To handle this track asynchronous invalidations (and also pageflip)
state per-ring and delay any in-between flushing until the rendering
has completed. And also cancel any delayed flushing if we get a new
invalidation request (whether delayed or not).
Also call intel_mark_fb_busy in both cases in all cases to make sure
that we keep the screen at the highest refresh rate both on flips,
synchronous plane updates and for frontbuffer rendering.
v2: Lots of improvements
Suggestions from Chris:
- Move invalidate/flush in flush_*_domain and set_to_*_domain.
- Drop the flush in busy_ioctl since it's redundant. Was a leftover
from an earlier concept to track flips/delayed flushes.
- Don't forget about the initial modeset enable/final disable.
Suggested by Chris.
Track flips accurately, too. Since flips complete independently of
rendering we need to track pending flips in a separate mask. Again if
an invalidate happens we need to cancel the evenutal flush to avoid
races.
v3:
Provide correct header declarations for flip functions. Currently not
needed outside of intel_display.c, but part of the proper interface.
v4: Add proper domain management to fbcon so that the fbcon buffer is
also tracked correctly.
v5: Fixup locking around the fbcon set_to_gtt_domain call.
v6: More comments from Chris:
- Split out fbcon changes.
- Drop superflous checks for potential scanout before calling intel_fb
functions - we can micro-optimize this later.
- s/intel_fb_/intel_fb_obj_/ to make it clear that this deals in gem
object. We already have precedence for fb_obj in the pin_and_fence
functions.
v7: Clarify the semantics of the flip flush handling by renaming
things a bit:
- Don't go through a gem object but take the relevant frontbuffer bits
directly. These functions center on the plane, the actual object is
irrelevant - even a flip to the same object as already active should
cause a flush.
- Add a new intel_frontbuffer_flip for synchronous plane updates. It
currently just calls intel_frontbuffer_flush since the implemenation
differs.
This way we achieve a clear split between one-shot update events on
one side and frontbuffer rendering with potentially a very long delay
between the invalidate and flush.
Chris and I also had some discussions about mark_busy and whether it
is appropriate to call from flush. But mark busy is a state which
should be derived from the 3 events (invalidate, flush, flip) we now
have by the users, like psr does by tracking relevant information in
psr.busy_frontbuffer_bits. DRRS (the only real use of mark_busy for
frontbuffer) needs to have similar logic. With that the overall
mark_busy in the core could be removed.
v8: Only when retiring gpu buffers only flush frontbuffer bits we
actually invalidated in a batch. Just for safety since before any
additional usage/invalidate we should always retire current rendering.
Suggested by Chris Wilson.
v9: Actually use intel_frontbuffer_flip in all appropriate places.
Spotted by Chris.
v10: Address more comments from Chris:
- Don't call _flip in set_base when the crtc is inactive, avoids redunancy
in the modeset case with the initial enabling of all planes.
- Add comments explaining that the initial/final plane enable/disable
still has work left to do before it's fully generic.
v11: Only invalidate for gtt/cpu access when writing. Spotted by Chris.
v12: s/_flush/_flip/ in intel_overlay.c per Chris' comment.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The downclocking checks a few more things, so not that simple to
convert. Also, this should get unified with the drrs handling and also
use the locking of that. Otoh the drrs locking is about as hapzardous
as no locking, at least on first sight.
For easier conversion ditch the upclocking on unload - we'll turn off
everything anyway.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We should be taking the right power well refs these days, so this
shouldn't be necessary. It also gets in the way of re-using these
routines for S0iX states, as those need all the power saving features
enabled.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't need to uninstall the full handler, simply disabling interrupts
ought to be enough.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
X could end up putting the fbcon fb into other domains, e.g.
for smooth take-overs. Also we want this for accurate frontbuffer
tracking: The set_config is an implicit flush and will re-enable
psr and similar features, so we need to bring the bo back into
the gtt domain.
v2: Add FIXME comment about fbcon locking fun in atomic context,
requested by Chris.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Can be useful to figure out imbalances and bugs in the frontbuffer
tracking.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So from just a quick look we seem to have enough information to
accurately figure out whether a given gem bo is used as a frontbuffer
and where exactly: We have obj->pin_count as a first check with no
false negatives and only negligible false positives. And then we can
just walk the modeset objects and figure out where exactly a buffer is
used as scanout.
Except that we can't due to locking order: If we already hold
dev->struct_mutex we can't acquire any modeset locks, so could
potential chase freed pointers and other evil stuff.
So we need something else. For that introduce a new set of bits
obj->frontbuffer_bits to track where a buffer object is used. That we
can then chase without grabbing any modeset locks.
Of course the consumers of this (DRRS, PSR, FBC, ...) still need to be
able to do their magic both when called from modeset and from gem
code. But that can be easily achieved by adding locks for these
specific subsystems which always nest within either kms or gem
locking.
This patch just adds the relevant update code to all places.
Note that if we ever support multi-planar scanout targets then we need
one frontbuffer tracking bit per attachment point that we expose to
userspace.
v2:
- Fix more oopsen. Oops.
- WARN if we leak obj->frontbuffer_bits when freeing a gem buffer. Fix
the bugs this brought to light.
- s/update_frontbuffer_bits/update_fb_bits/. More consistent with the
fb tracking functions (fb for gem object, frontbuffer for raw bits).
And the function name was way too long.
v3: Size obj->frontbuffer_bits correctly so that all pipes fit in.
v4: Don't update fb bits in set_base on failure. Noticed by Chris.
v5: s/i915_gem_update_fb_bits/i915_gem_track_fb/ Also remove a few
local enum pipe variables which are now no longer needed to make the
function arguments no drop over the 80 char limit.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It doesn't make sense to never again schedule the work, since by the
time we might want to re-enable psr the world might have changed and
we can do it again.
The only exception is when we shut down the pipe, but that's an
entirely different thing and needs to be handled in psr_disable.
Note that later patch will again split psr_exit into psr_invalidate
and psr_flush. But the split is different and this simplification
helps with the transition.
v2: Improve the commit message a bit.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have _enable/_disable interfaces now for the modeset sequence and
intel_edp_psr_exit for workarounds.
The callsites in intel_display.c are all redundant with the modeset
sequence enable/disable calls in intel_ddi.c. The one in
intel_sprite.c is real and needs to be switched to psr_exit.
If this breaks anything then we need to augment the enable/disable
functions accordingly.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's not needed and further more will get in the way of a sane
locking scheme - psr_exit _can't_ take modeset locks due to lock
inversion, and at least once dp mst hits the connector list
is no longer static.
But since we track all state in dev_priv->psr there is no need
at all.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
First round of fixes for 3.16-rc, mostly cc: stable, and the vt/vgacon
fixes from Daniel [1] to avoid hangs and unclaimed register errors on
module load/reload.
* tag 'drm-intel-fixes-2014-06-17' of git://anongit.freedesktop.org/drm-intel:
drm/i915/bdw: remove erroneous chv specific workarounds from bdw code
drm/i915: fix possible refcount leak when resetting forcewake
drm/i915: Reorder semaphore deadlock check
drm/i95: Initialize active ring->pid to -1
drm/i915: set backlight duty cycle after backlight enable for gen4
drm/i915: Avoid div-by-zero when pixel_multiplier is zero
drm/i915: Disable FBC by default also on Haswell and later
drm/i915: Kick out vga console
drm/i915: Fixup global gtt cleanup
vt: Don't ignore unbind errors in vt_unbind
vt: Fix up unregistration of vt drivers
vt: Fix replacement console check when unbinding
The acquire ctx will typically be declared on the stack, which means we
could have garbage values for any uninitialized field. In this case, it
was triggering WARN_ON()s because 'contended' had garbage value.
Go ahead and use memset() to be more future-proof.
v2: now with extra brown paper bag
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes a regression in 3.16-rc1 compared to 3.15.
The unbalanced calls would presumably result in the page flip interrupts
never getting disabled once they are enabled.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 75f36d8619.
drm_vblank_get() is necessary to ensure the DRM vblank counter value is
up to date in drm_send_vblank_event().
Seems to fix weston hangs waiting for page flips to complete.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Make sure we have an HDMI monitor before validating modes with
clocks >165 Mhz on single link connections.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to use the adjusted clock on dce8 as well.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=80029
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The original comment that introduced it said:
commit 0009e46cd5
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Fri Dec 6 14:11:02 2013 -0800
drm/i915: Track which ring a context ran on
Previously we dropped the association of a context to a ring. It is
however very important to know which ring a context ran on (we could
have reused the other member, but I was nitpicky).
This is very important when we switch address spaces, which unlike
context objects, do change per ring.
As an example, if we have:
RCS BCS
ctx A
ctx A
ctx B
ctx B
Without tracking the last ring B ran on, we wouldn't know to switch the
address space on BCS in the last row.
But this is not really true, because we are already checking to != from (with
"from" being = ring->last_context) and that should be enough to make sure we
switch to the right address space.
We would have a problem if we switched the context object for every ring (since
then we would fail to do it in some situations) but we only switch it for the
render ring, so we don't care.
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Jesse's SOix work required some patches from acpi-next, so pull it in
through a topic barnch.
Conflicts:
drivers/gpu/drm/i915/i915_drv.c
drivers/gpu/drm/i915/intel_pm.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
couple more DP regression fixes.
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/disp: fix oops in destructor with headless cards
drm/gf117/i2c: no aux channels on this chipset
If init doesn't run then disp->outp might not be initialized, resulting
in an oops.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Otherwise, we might receive a new interrupt before we have time to
ack the first one, eventually missing it.
Without an atomic XCHG operation with mmio space, this patch merely
reduces the window in which we can miss an interrupt (especially when
you consider how heavyweight the I915_READ/I915_WRITE operations are).
Notice that, before clearing a port-sourced interrupt in the IIR, the
corresponding interrupt source status in the PORT_HOTPLUG_STAT must be
cleared.
Spotted by Bob Beckett <robert.beckett@intel.com>.
v2:
- Add warning to commit message and comments to the code as per Chris
Wilson's request.
- Imre Deak pointed out that the pipe underrun flag might not be signaled
in IIR, so do not make valleyview_pipestat_irq_handler depend on it.
v3: Improve the source code comment.
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise, we might receive a new interrupt before we have time to
ack the first one, eventually missing it.
The right order should be:
1 - Disable Master Interrupt Control.
2 - Find the category of interrupt that is pending.
3 - Find the source(s) of the interrupt and clear the Interrupt Identity bits (IIR)
4 - Process the interrupt(s) that had bits set in the IIRs.
5 - Re-enable Master Interrupt Control.
Without an atomic XCHG operation with mmio space, the above merely reduces the window
in which we can miss an interrupt (especially when you consider how heavyweight the
I915_READ/I915_WRITE operations are).
Spotted by Bob Beckett <robert.beckett@intel.com>.
v2: Add warning to commit message and comments to the code as per Chris Wilson's request.
v3: Improve the source code comment.
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise, we might receive a new interrupt before we have time to
ack the first one, eventually missing it.
Without an atomic XCHG operation with mmio space, this patch merely
reduces the window in which we can miss an interrupt (especially when
you consider how heavyweight the I915_READ/I915_WRITE operations are).
Notice that, before clearing a port-sourced interrupt in the IIR, the
corresponding interrupt source status in the PORT_HOTPLUG_STAT must be
cleared.
Spotted by Bob Beckett <robert.beckett@intel.com>.
v2:
- Reorder the IIR clearing to reduce the window even further.
- Add warning to commit message and comments to the code as per Chris
Wilson's request.
- Imre Deak pointed out that the pipe underrun flag might not be signaled
in IIR, so do not make valleyview_pipestat_irq_handler depend on it.
v3: Improve the source code comment.
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise, we might receive a new interrupt before we have time to ack the first
one, eventually missing it.
According to BSPec, the right order should be:
1 - Disable Master Interrupt Control.
2 - Find the source(s) of the interrupt.
3 - Clear the Interrupt Identity bits (IIR).
4 - Process the interrupt(s) that had bits set in the IIRs.
5 - Re-enable Master Interrupt Control.
Without an atomic XCHG operation with mmio space, the above merely reduces the window
in which we can miss an interrupt (especially when you consider how heavyweight the
I915_READ/I915_WRITE operations are).
We maintain the "disable SDE interrupts when handling" hack since apparently it works.
Spotted by Bob Beckett <robert.beckett@intel.com>.
v2: Add warning to commit message and comments to the code as per Chris Wilson's request.
v3: Improve the source comments.
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A WARN_ON is perfectly fine.
The BUG in here seems to be the cause behind hard-hangs when I cat the
i915_gem_pageflip debugfs file (which calls this from an irq
spinlock). But only while running a full igt run after a while. I
still need to root cause the underlying issue.
I'll also start reject patches which add new BUG_ON but don't come
with a really good justification for it. The general rule really
should be to just WARN and hope the driver survives for long enough.
v2: Make the WARN a bit more useful per Chris' suggestion.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We could walk of a bad list otherwise when someone concurrently
unbinds stuff for fun.
I've suspected this as the root-cause behind seemingly inconsistent
state, but alas it's not.
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Beignet needs these in order to program the L3 cache config for
OpenCL workloads, particularly when using SLM.
Signed-off-by: Brad Volkin <bradley.d.volkin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Take the minimum of the object size and the vma size and prefault
only that much. Avoids a SIGBUS when mmapping only a portion of the
object.
Prefaulting was introduced here:
commit b90b91d870
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Jun 10 12:14:40 2014 +0100
drm/i915: Prefault the entire object on first page fault
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Testcase: igt/gem_mmap/short-mmap
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch enables the framework for using MMIO based flip calls,
in contrast with the CS based flip calls which are being used currently.
MMIO based flip calls can be enabled on architectures where
Render and Blitter engines reside in different power wells. The
decision to use MMIO flips can be made based on workloads to give
100% residency for Media power well.
v2: The MMIO flips now use the interrupt driven mechanism for issuing the
flips when target seqno is reached. (Incorporating Ville's idea)
v3: Rebasing on latest code. Code restructuring after incorporating
Damien's comments
v4: Addressing Ville's review comments
-general cleanup
-updating only base addr instead of calling update_primary_plane
-extending patch for gen5+ platforms
v5: Addressed Ville's review comments
-Making mmio flip vs cs flip selection based on module parameter
-Adding check for DRIVER_MODESET feature in notify_ring before calling
notify mmio flip.
-Other changes mostly in function arguments
v6: -Having a seperate function to check condition for using mmio flips (Ville)
-propogating error code from i915_gem_check_olr (Ville)
v7: -Adding __must_check with i915_gem_check_olr (Chris)
-Renaming mmio_flip_data to mmio_flip (Chris)
-Rebasing on latest nightly
v8: -Rebasing on latest code
-squash 3rd patch in series(mmio setbase vs page flip race) with this patch
-Added new tiling mode update in intel_do_mmio_flip (Chris)
v9: -check for obj->last_write_seqno being 0 instead of obj->ring being NULL in
intel_postpone_flip, as this is a more restrictive condition (Chris)
v10: -Applied Chris's suggestions for squashing patches 2,3 into this patch.
These patches make the selection of CS vs MMIO flip at the page flip time, and
make the module parameter for using mmio flips as tristate, the states being
'force CS flips', 'force mmio flips', 'driver discretion'.
Changed the logic for driver discretion (Chris)
v11: Minor code cleanup(better readability, fixing whitespace errors, using
lockdep to check mutex locked status in postpone_flip, removal of __must_check
in function definition) (Chris)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Sourab Gupta <sourab.gupta@intel.com>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk> # snb, ivb
[danvet: Fix up parameter alignement checkpatch spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Staring from HSW, the resolution limit of FBC has increased to
4096*4096
Issue: VIZ-2813
Change-Id: I842f64e3cf2c0d18d29ef1bcfef3b9bb1f1764ac
Signed-off-by: Daisy Sun <daisy.sun@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This adds support for a write-enable bit in the entry of GTT.
This is handled via a read-only flag in the GEM buffer object which
is then used to see how to set the bit when writing the GTT entries.
Currently by default the Batch buffer & Ring buffers are marked as read only.
v2: Moved the pte override code for read-only bit to 'byt_pte_encode'. (Chris)
Fixed the issue of leaving 'gt_old_ro' as unused. (Chris)
v3: Removed the 'gt_old_ro' field, now setting RO bit only for Ring Buffers(Daniel).
v4: Added a new 'flags' parameter to all the pte(gen6) encode & insert_entries functions,
in lieu of overloading the cache_level enum (Daniel).
v5: Removed the superfluous VLV check & changed the definition location of PTE_READ_ONLY flag (Imre)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
two fixes for the deep color support in radeon.
* 'drm-next-3.16' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: Bypass hw lut's for > 8 bpc framebuffer scanout.
drm/radeon: use pixel formats instead of depth/bpp
This is bigger because it regenerates the internal firmwares after a fix.
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/doc: update the thermal documentation
drm/nouveau/pwr: fix typo in fifo wrap handling
drm/nv50/disp: fix a potential oops in supervisor handling
drm/nouveau/disp/dp: don't touch link config after success
drm/nouveau/kms: reference vblank for crtc during pageflip.
drm/gk104/fb/ram: fixups from an earlier search+replace
drm/nv50/gr: remove an unneeded write while initialising PGRAPH
drm/nv50/gr: fix overlap while zeroing zcull regions
drm/gf100-/gr: report class data to host on fwmthd failure
drm/gk104/ibus: increase various random timeouts
drm/gk104/clk: only touch divider for mode we'll be using
Need to drm_vblank_get/put() the crtc involved in a
pending pageflip, or we might not get vblank irqs and
updates of vblank counts and timestamps for pageflip
events and flip completion.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org
The blob does not seem to write at that place for my NVAC, though it
does for my NV96, agreeing with what is done in the if/else structure
below. I guess someone forgot to remove the line when the if/else was
put in place.
Signed-off-by: Pierre Moreau <pierre.morrow@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The specified stride was not correct, resulting in erases overlapping
and part of the zcull regions being not erased at all.
Signed-off-by: Pierre Moreau <pierre.morrow@free.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
