pvrusb2: The origin of the capability bounds rectangle may differ from
(left=0,top=0) so the calculation should use absolute coordinates,
here below, or use relative coordinates like
cropl_val-cap->bounds.left and cropt_val-cap->bounds.top.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
pvrusb2: Recognize and handle mode change before dealing with changes
related to the video standard. Even though the video standard should
only matter when in analog mode, doing this way is technically cleaner
in case there's other stuff that might depend on both.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This tuner PLL has missing initialisation settings resulting in
haphazard tuning. The PLL LPF was set to just 22000 symbol rate.
Basically, the module is a Sharp BS2F7HZ0194 (STV0299+IX2410)
I have had problems implementing the PLL in a new driver and
did not want to break the IX2410 out of the PLL.
This applies to DW2102, DM1105, CX88 and OPERA1 drivers.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since the drivers/ieee1394/ backend was removed from firedtv, its I/O no
longer needs to be abstracted as exchangeable backend methods.
Also, ieee1394 variants of module and device probe and removal are no
longer there. Move module probe and removal into firedtv-fw.c where
device probe and removal are implemented.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Speed up tuning, as firmware is not necessary to load every attempt to tune
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Decrease firmware loading time. Before it is ~4000 i2c calls,
now it is ~256 i2c calls to load ds3000 firmware.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
TeVii s480 works fine with that on DVB-S2 channels
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make some initializations in init, not in tune function
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds audio DMA capture and ALSA mixer elements for the line
input jack of the Hauppauge Nova-S-plus DVB-S PCI card. The Nova-S-plus
has a WM8775 ADC that is currently not detected. This patch enables
this chip and exports volume, balance mute and ALC elements for ALSA
mixer controls.
[mchehab@redhat.com: Changed the patch to only talk with wm8775 if board
info says so. Also, added platform_data support, to avoid changing the
behaviour for other boards, and fixed CodingStyle]
[awalls@md.metrocast.net: Changed patch to make the WM8775_GID defintion
bridge driver private and let the bridge driver set the value of
v4l2_subdev.grp_id.]
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Add one more radio input, usefull for tm6010
Add control output amplitude.
Add set_config function for configure tuner when TV card hasn't dvb part.
Signed-off-by: Beholder Intl. Ltd. Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add linux/sched.h because of missing declaration of TASK_NORMAL.
This patch fixes the following error:
drivers/media/video/omap24xxcam.c: In function
'omap24xxcam_vbq_complete':
drivers/media/video/omap24xxcam.c:415: error: 'TASK_NORMAL' undeclared
(first use in this function)
drivers/media/video/omap24xxcam.c:415: error: (Each undeclared
identifier is reported only once
drivers/media/video/omap24xxcam.c:415: error: for each function it
appears in.)
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes the warning "Using plain integer as NULL pointer",
generated by sparse, by replacing
if (var == 0)
with
if (!var)
after an allocation
and all other offending 0s with NULL.
KernelVersion: linus' tree-1f0324c
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The cxhdl->priv field was not set initially, only after capturing started.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It takes too long time to scan due to low symbol rate PID's
like PAT, PMT, CAT, NIT.
For that matter we enabled permanently all PID's
less 0x20 in hardware PID filter for NetUP Dual DVB-T/C CI RF card
to combine rates.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is needed for multifrontend support.
NetUP Dual DVB-T/C CI RF card has frontends connected to port B & C
Each frontend has two switchable cores - DVB-T & DVB-C
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is two external I2C buses in cx23885 chip.
Currently, analog tuners supported for second I2C bus only
In NetUP Dual DVB-T/C CI RF card tuners connected to first bus
So, in order to support analog tuners sitting on first bus
we need modifications.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The card based on cx23885 PCI-e brige. Altera FPGA for CI,
multistandard demods stv0367 from STM for QAM & OFDM, Xcieve xc5000 tuners
and additional cx25840 for second analog input.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The STV0367 is a multi-standard demodulator which is
capable of processing DVB-T as well as DVB-C signals.
It is fully compliant with DVB-T and DVB-C
recommendations for broadcast services.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
An Altera FPGA CI module for NetUP Dual DVB-T/C RF CI card.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes the warning "Using plain integer as NULL pointer",
generated by sparse, by replacing the offending 0s with NULL.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Reviewed-by: Devin Heitmueller <dheitmueller@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This soc_camera driver is for Omnivision's OV9740 sensor. This initial
submission provides support for YUV422 output at 1280x720 (720p), which is
the sensor's native resolution. 640x480 (VGA) is also supported, with
cropping and scaling performed by the sensor's ISP.
This driver is heavily based off of the existing OV9640 driver.
Signed-off-by: Andrew Chew <achew@nvidia.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that soc-camera supports videobuf API v1 and v2, camera-host drivers
can be converted to videobuf2 individually. This patch converts the
mx3_camera driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Extend soc-camera core to also support the videobuf2 API.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
videobuf2-memops and videobuf2-core can be compiled as modules, in which
case 3 more symbols from videobuf2-memops.c have to be exported.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the camera was set to output formats like RGB565 YUYV or SBGGR10,
the resulting image was scrambled due to erroneous interpretations of
horizontal parameter's units.
This patch in fourcc_to_ipu_pix, eliminate also the pixel formats mappings
that, first are not used within mainline code and second, standing at
the datasheets, they will not work properly:
The IPU internal bus support only the following data formatting
(44.1.1.3 Data Flows and Formats):
1 YUV 4:4:4 or RGB-8 bits per color component
2 YUV 4:4:4 or RGB-10 bits per color component
3 Generic data (from sensor to the system memory only)
And format conversions are done:
- from memory: unpacking from other formats to IPU supported ones
- to memory: packing in the inverse order.
So, assigning a packing/unpacking strategy to the IPU for those formats
will produce a packing to memory and not the inverse.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The 'pix->width' field may be updated in mx3_camera_set_fmt() to
fulfill the IPU stride line alignment requirements. If this update
takes place, the 'fmt.pix.sizeimage' field in the struct v4l2_format
stucture returned by VIDIOC_S_FMT is wrong. We need to update the
'pix->sizeimage' field in the mx3_camera_set_fmt() function to fix
this issue.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Even though clk_put() is a no-op on most architectures it is not for
some ARM implementations. To not fail on those, release the clock timer
before freeing the surrounding structure.
This bug was spotted by the semantic patch tool coccinelle using the
script found at scripts/coccinelle/free/kfree.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a function to calculate the number of samples on the media-bus,
required to retrieve one pixel of a certain format.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some camera systems have strong requirement for capturing
an exact number of frames after starting the stream and do
not tolerate losing captured frames. By starting the stream
after the videobuf has queued the buffers, we ensure that
no frame will be lost.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reported by, and based on a patch from, Martin Dauskardt.
The AUDIO_AC3_BITRATE control is still missing from this list, but such
optional controls are a bit hard to handle. This will be fixed automatically
when we switch to the control framework.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reported-by: Martin Dauskardt <martin.dauskardt@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/ieee1394/ has been removed in Linux 2.6.37. The corresponding
backend code in firedtv is no longer built in now and can be deleted.
Firedtv continues to work with drivers/firewire/.
Also, fix a Kconfig menu comment: Removal of CONFIG_IEEE1394 made the
"Supported FireWire (IEEE 1394) Adapters" comment disappear; bring it back
with corrected dependency.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some ioctl's were defined wrong on 2.6.2 and 2.6.6, using the wrong
type of R/W arguments. They were fixed, but the old ioctl names are
still there, maintained to avoid breaking binary compatibility:
There's no sense on preserving those forever, as it is very doubtful
that someone would try to use a such old binary with a modern kernel.
Removing them will allow us to remove some magic done at the V4L ioctl
handler.
Note that any application compiled with a videodev2.h from 2.6.7 or later
will be using the correct ioctls.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Having a framerate divisor of 3 is not really necesarry and leads to
various troubles (frames going missing, compression issues) when allowed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a complete rewrite of the old v4l1 vicam subdriver, featuring
multiple resolutions, gain + exposure control and still has less code.
Oh and it is a v4l2 driver rather then v4l1 ofcourse :)
Many thanks to Devin Heitmueller <dheitmueller@kernellabs.com> for
donating his 3com homeconnect to me, which made this rewrite possible.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In good lighting conditions (lots of details visible) the current buffers
are sometimes too small.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This fixes the led not working on this camera
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested with a camera with usb-id: 0c45:62bb
Also enable dmi based flopped laptop detection for the 0c45:627b ov7660 model.
Some of the MSI laptops with upside down camera have this one instead of the
0c45:624f.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested with a camera with usb-id: 0c45:62bb
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
During image capture, the filling rate of the isoc packets is computed.
It is then used by a work queue to update the current JPEG quality.
Tested-by: Franck Bourdonnec <fbourdonnec@chez.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A marker 'ff ff 00 c4 c4 96' indicates an end of frame.
It is 62 bytes long and may be splitted on 2 packets.
It contains a flag 'USB full' which indicates that the frame is truncated.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2-ctl and qv4l2 enumerate controls using V4L2_CTRL_FLAG_NEXT_CTRL,
falling back to the old method if the flag isn't supported.
The v4l2_subdev_queryctrl function will currently handle that flag, but
for the controls of the subdev only. This isn't right, it should refuse
this flag, otherwise v4l2-ctl will only see the controls of the first
subdev.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Subdev controls return codes are evil, as they return -EINVAL to mean
both unsupported and invalid arguments. Due to that, we need to use a
trick to identify what controls are supported by a subdev.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On some cases, driver returns 1. This should be OK, but qv4l2 is too
strict about return values.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Having the device detection happening at reset is bad, as every time,
it will produce a message like:
tvp5150 2-005c: tvp5150am1 detected.
This only polutes the log and for an accidental kernel hacker, it looks
like a real problem. So, move those printk's to happen during device
probe.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It makes no sense that tuner_lookup would touch at the standby
state. Remove it.
Thanks-to: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Group a few functions together and add/fix comments for each
block of the driver.
This is just a cleanup patch meant to improve driver readability.
No functional changes in this patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver is complex, and used by everyone. Better to have it
properly documented.
No functional changes are done in this patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
tuner-core has no business to do with digital TV. So, don't use
T_DIGITAL_TV on it, as it has no code to distinguish between
them, and nobody fills T_DIGITAL_TV right.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
tda9887 used to use the T_STANDBY type internally, while tea5761
used it to put the device to sleep. Fix the code for it to work
properly with the tuner core changes and remove this flag from
tuner.h.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the now obsolete set_freq. Also merge set_addr and set_type_addr.
In the past, it used to have two different setup calls, one to set just
the tuner type to any tuner found, and another to set the type only if
the address matches. Those two internal calls were grouped together,
but the functions weren't merged, making the code uglier.
No functional changes are done in this patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A static var is evil, especially if a device has two boards with
xc5000. Instead, just like the other drivers, use stack to store
its config during setup.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Power down tuners at suspend. At resume, if the tuner is in standby,
calls set_mode, that will turn it on and set the latest frequencies.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the past, T_STANDBY were used on devices with a separate radio tuner to
mark a tuner that were disabled. With the time, it got newer meanings.
Also, due to a bug at the logic, the driver might incorrectly return
T_STANDBY to userspace.
So, instead of keeping the abuse, just use a boolean for storing
such information.
We can't remove T_STANDBY yet, as this is used on two other drivers. A
latter patch will address its usage outside tuner-core.
Thanks-to: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Properly document those functions and do some cleanups around that.
There's just one behavior change on this patchset: it will now restore
TV frequency when changing from radio to TV mode.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a big patch with no functional changes. It just
rearranges everything inside the driver, and prepares to
break TV and Radio into two separate fops groups.
Currently, it has an heuristics logic to determine if the
call came from radio or video. However, the caller driver
knows for sure, so tuner-core shouldn't try to guess it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After registering the cdev, it would be possible do have an open on it.
In a matter of fact, some versions of udev do this. So, move registration
to the end and protect it with a mutex.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds support for Pixelviex Xcapture USB grabber device.
This device has one composite and one s-video entry
only, plus a button.
For now, the button is not supported.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some devices don't need to use it. So allow to just disable this logic.
Having it enabled on some devices cause power management to complain,
generating error -71.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of per-model tests all over the code, use some parameters
at the board entries to describe the model variants for:
- devices with 417 MPEG encoder;
- devices that use external AV;
- devices where vbi VANC endpoint doesn't work;
- devices with xc5000 that require different IF
initialization (and probably will cover also
xc3028).
- devices with xceive tuner that require a reset
during init.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The check for xc5000 assumes that the tuner will always
be using the same bus and will have the same address.
As those are configurable via dev->board, it should use,
instead, the values defined there.
Also, a similar type of test will be needed by other
tuners (for example, for TUNER_XC2028)
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Just a cleanup patch. Removes one indent level by moving
the return -ENODEV to happen before the device register
logic, if the interface is not the audio/video (int 1).
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
My Hauppauge WinTV HVR-1400 needs sometimes more then only one retry to load the firmware successfully.
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
KERNEL_VERSION: 2.6.37
common.c in function ssize_t si470x_fops_read.
1. First mutex_lock on &radio->lock in line 441
2. Second in line 462
I think that mutex in line 462 is not needed.
433static ssize_t si470x_fops_read(struct file *file, char __user *buf,
434 size_t count, loff_t *ppos)
435{
....
441 mutex_lock(&radio->lock);
442 if ((radio->registers[SYSCONFIG1] & SYSCONFIG1_RDS) == 0)
443 si470x_rds_on(radio);
444
445 /* block if no new data available */
446 while (radio->wr_index == radio->rd_index) {
447 if (file->f_flags & O_NONBLOCK) {
448 retval = -EWOULDBLOCK;
449 goto done;
450 }
451 if (wait_event_interruptible(radio->read_queue,
452 radio->wr_index != radio->rd_index) < 0) {
453 retval = -EINTR;
454 goto done;
455 }
456 }
457
458 /* calculate block count from byte count */
459 count /= 3;
460
461 /* copy RDS block out of internal buffer and to user buffer */
462 mutex_lock(&radio->lock);
Found by Linux Device Drivers Verification Project
Remove second mutex.
Signed-off-by: Alexander Strakh <strakh@ispras.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Unable to test this due to lack of hardware.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/vivi.c:1059: warning: this decimal constant is unsigned only in ISO C90
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Also fixed a memory leak in the probe function if an error occurred.
The gain control range was also fixed (a proper range from -64 to 64).
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When a device is not detected, the driver prints a warning message.
That's ok, except for the fact that, even on newer devices that have
eeprom but aren't yet supported, it prints a message saying that the
device doesn't have eeprom.
Fix it by having a separate message for devices with eeprom, but not
yet known by the driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make vivi use videobuf2 in place of videobuf.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver is abusing the kernel<=>userspace API, due to the lack of a
proper solution for it. A discussion were done at:
http://www.mail-archive.com/linux-media@vger.kernel.org/msg22196.html
But there's not a solution for it yet. So, move the driver to staging, while
we don't have a final solution.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
22kHz workaround must also be performed for the 2nd frontend.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Refactored code for channel initialisation and release:
- Do not create device nodes which are not required.
- Better error handling.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do not clear registers ACLC/BCLC in DVB-S2 mode for Cut <= 20.
Otherwise, the demod could lose the lock periodically.
Verified with cineS2 and Duoflex.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixed typos in register macros.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add dvb net device.
Note that the physical address must be setup manually.
Signed-off-by: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Implement shutdown workaround for some chipsets.
Signed-off-by: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Driver for the Common Interface Controller CXD2099AR.
Supports the CI of the cineS2 DVB-S2.
For now, data is passed through '/dev/dvb/adapterX/sec0':
- Encrypted data must be written to 'sec0'.
- Decrypted data can be read from 'sec0'.
- Setup the CAM using device 'ca0'.
Signed-off-by: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If tuner initialisation failed, the frontend node was not removed.
When the frontend was opened, a kernel oops occurred...
This is the first step to improve error handling during initialisation.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Support up to 4 tuners for cineS2 v5, duoflex & mystique v2.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Card driver may supply its own lock routine now.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The STV0900 features two demodulator paths in one chip. Thus it is not
possible to use the generic power off function of the chip when sending
one of them to standby. The other path will stop working in that case.
The sleep function now switches off functionality specific to the demod
path. The global stuff is only switched off, when both paths are in
sleep mode. The wakeup function always turns on the global functionality
and then works specific to the path.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ERROR: switch and case should be at the same indent
switch (ch->u.ofdm.transmission_mode) {
[...]
+ case TRANSMISSION_MODE_4K:
WARNING: please, no spaces at the start of a line
+ case TRANSMISSION_MODE_4K:$
ERROR: switch and case should be at the same indent
switch (ch->u.ofdm.transmission_mode) {
[...]
+ case TRANSMISSION_MODE_4K:
WARNING: please, no spaces at the start of a line
+ case TRANSMISSION_MODE_4K:$
ERROR: switch and case should be at the same indent
switch (ch->u.ofdm.transmission_mode) {
[...]
+ case TRANSMISSION_MODE_4K:
WARNING: please, no spaces at the start of a line
+ case TRANSMISSION_MODE_4K:$
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for the SoC DiB7090 DVB-T demodulator and its
melt-in UHF/VHF RF tuner.
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patchs add initial support for the DiB9000-device. This
demodulator is firmware-driven.
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds several performance improvements and prepares the
usage of firmware-based devices.
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds the possibitity to use different I2C-ports to talk to
slave-devices than the standard ones.
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a set a functions which allow the handling of multiple
demodulator in a diversity reception chain.
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This commit adds a function to the DiB0700 USB driver which allows
drivers to change the I2C clock speed.
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add I2C/V4L2 subdev driver for Siliconfile NOON010PC30 CIF camera.
The driver implements basic functionality, i.e. CIF/QCIF/QQCIF
resolution and color format selection, automatic/manual color
balance control. Other functions like cropping, rotation/flip,
exposure etc. can be easily implemented if needed.
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When is called fimc_stop_capture, it seems that wait_event_timeout
used improperly. It should be wake up by irq handler.
Reviewed-by Jonghun Han <jonghun.han@samsung.com>
Signed-off-by: Sungchun Kang <sungchun.kang@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes the value of FIFO_CTRL in MSCTRL.
Main-scaler has the value to specify a basis FIFO control of input DMA.
The description of FIFO_CTRL has been changed as below.
0 = FIFO Empty (Next burst transaction is possible when FIFO is empty)
1 = FIFO Full (Next burst transaction is possible except Full FIFO)
Value '1' is recommended to enhance the FIMC operation performance.
Reviewed-by: Jonghun Han <jonghun.han@samsung.com>
Signed-off-by: Hyunwoong Kim <khw0178.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds callback functions, stop_streaming and job_abort,
to abort or finish any DMA in progress. stop_streaming is called
by videobuf2 framework and job_abort is called by m2m framework.
ST_M2M_PEND state is added to discard the next job.
Reviewed-by: Jonghun Han <jonghun.han@samsung.com>
Signed-off-by: Hyunwoong Kim <khw0178.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Horizontal and vertical scaling range are according to the following equations.
If (SRC_Width >= 64 x DST_Width) { Exit(-1); /* Out of Horizontal scale range}
If (SRC_Height >= 64 x DST_Height) { Exit(-1); /* Out of Vertical scale range}
fimc_check_scaler_ratio() is used to check if horizontal and vertical
scale range are valid or not. To use fimc_check_scaler_ratio,
source and destination format should be set by VIDIOC_S_FMT.
And in case of scaling up, it doesn't have to check the scale range.
Reviewed-by: Jonghun Han <jonghun.han@samsung.com>
Signed-off-by: Hyunwoong Kim <khw0178.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The main scaler has four SFRs for main scaler ratio depending on FIMC version.
FIMC 4.x has only two SFRs and FIMC 5.x has four SFRs for main scaler.
Those are MainHorRatio, MainHorRatio_ext, MainVerRatio and MainverRatio_ext.
The FIMC 5.x has 15 bit resolution for scaling ratio as below.
{MainHorRatio,MainHorRatio_ext} = {[14:6],[5:0]}.
{MainVerRatio,MainVerRatio_ext} = {[14:6],[5:0]}.
MainHorRatio = CISCCTRL[24:16], MainHorRatio_ext = CIEXTEN[15:10]
MainVerRatio = CISCCTRL[8:0], MainVerRatio_ext = CIEXTEN[5:0]
This patch supports FIMC 4.x and FIMC 5.x using platform_device_id::driver_data.
Reviewed-by: Jonghun Han <jonghun.han@samsung.com>
Signed-off-by: Hyunwoong Kim <khw0178.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some color formats are mismatched in s5p-fimc driver.
CIOCTRL[1:0], order422_out, should be set 2b'00 not 2b'11
to use V4L2_PIX_FMT_YUYV. Because in V4L2 standard V4L2_PIX_FMT_YUYV means
"start + 0: Y'00 Cb00 Y'01 Cr00 Y'02 Cb01 Y'03 Cr01". According to datasheet
2b'00 is right value for V4L2_PIX_FMT_YUYV.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Manage the camera sensor clock in the host driver rather than
leaving this task for sensor drivers. The clock frequency
must be passed in the sensor's and host driver's platform data.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Map all (0, 90, 180, 270) deg counterclockwise rotation and
horizontal and vertical flip controls to (0, 90) deg rotation,
horizontal and vertical flip transformations available
in the device.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Increase the input DMA "successive burst count" to default
value 4 to improve DMA performance. Minor cleanup.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Prevent VIDIOC_STREAMON failing when s_stream callback is
not implemented by a sensor subdev driver.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove bus_width from s5p_fimc_isp_info data structure.
Determine camera data bus width based on mediabus pixel format.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change s3c_fimc.h header file name to s5p_fimc.h, replace s3c_fimc_*
names with s5p_fimc_*. s3c_fimc need to be reserved for S3C series
and s5p-fimc driver will not cover CAMIF devices in S3C SoC series.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Conversion to multiplanar color formats and minor cleanup.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Porting to videobuf 2 and minor cleanup.
Separate videobuf_queue_ops are are created for m2m
and capture video nodes.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch ports mem2mem test device to videobuf2 framework.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Port memory-to-memory framework to videobuf2 framework.
Add support for multi-planar Video for Linux 2 API extensions to the
memory-to-memory driver framework.
Based on the original patch written by Pawel Osciak.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/videobuf2-core.c: In function ‘__vb2_perform_fileio’:
drivers/media/video/videobuf2-core.c:1638: warning: format ‘%ld’ expects type ‘long int’, but argument 4 has type ‘size_t’
drivers/media/video/videobuf2-core.c:1697: warning: format ‘%ld’ expects type ‘long int’, but argument 2 has type ‘size_t’
drivers/media/video/videobuf2-core.c:1703: warning: format ‘%ld’ expects type ‘long int’, but argument 2 has type ‘size_t’
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a generic file io (read and write) emulator for videobuf2. It uses
MMAP memory type buffers and generic vb2 calls: req_bufs, qbuf and
dqbuf. Video date is being copied from mmap buffers to userspace with
standard copy_to_user() function. To add support for file io the driver
needs to provide an additional callback - read_setup or write_setup. It
should provide the default number of buffers used by emulator and flags.
With these flags one can detemine the style of read() or write()
emulation. By default 'streaming' style is used. With
VB2_FILEIO_READ_ONCE flag one can select 'one shot' mode for read()
emulator. With VB2_FILEIO_WRITE_IMMEDIATE flag one can select immediate
conversion of write calls to qbuf for write() emulator, so the vb2 will
not wait until each buffer is filled completely before queueing it to
the driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an implementation of DMA scatter/gather allocator and handling
routines for videobuf2.
For mmap operation mode it is implemented on top of
alloc_page + sg_set_page/_free_page.
For userptr operation mode it is implemented on top of
get_user_pages + sg_set_page/put_page.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an implementation of DMA coherent memory allocator and handling
routines for videobuf2, implemented on top of dma_alloc_coherent() call.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an implementation of contiguous virtual memory allocator and handling
routines for videobuf2, implemented on top of vmalloc()/vfree() calls.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Videobuf2 is a Video for Linux 2 API-compatible driver framework for
multimedia devices. It acts as an intermediate layer between userspace
applications and device drivers. It also provides low-level, modular
memory management functions for drivers.
Videobuf2 eases driver development, reduces drivers' code size and aids in
proper and consistent implementation of V4L2 API in drivers.
Videobuf2 memory management backend is fully modular. This allows custom
memory management routines for devices and platforms with non-standard
memory management requirements to be plugged in, without changing the
high-level buffer management functions and API.
The framework provides:
- implementations of streaming I/O V4L2 ioctls and file operations
- high-level video buffer, video queue and state management functions
- video buffer memory allocation and management
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add multi-planar ioctl handling to the 32bit compatibility layer.
[mchehab@redhat.com: Merged with a fixup patch from Pawel]
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Multi-planar API is as a backwards-compatible extension of the V4L2 API,
which allows video buffers to consist of one or more planes. Planes are
separate memory buffers; each has its own mapping, backed by usually
separate physical memory buffers.
Many different uses for the multi-planar API are possible, examples
include:
- embedded devices requiring video components to be placed in physically
separate buffers, e.g. for Samsung S3C/S5P SoC series' video codec,
Y and interleaved Cb/Cr components reside in buffers in different
memory banks;
- applications may receive (or choose to store) video data of one video
buffer in separate memory buffers; such data would have to be temporarily
copied together into one buffer before passing it to a V4L2 device;
- applications or drivers may want to pass metadata related to a buffer and
it may not be possible to place it in the same buffer, together with video
data.
[mchehab@redhat.com: CodingStyle fixes]
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb/dvb-usb/technisat-usb2.c: In function ‘technisat_usb2_disconnect’:
drivers/media/dvb/dvb-usb/technisat-usb2.c:770: warning: ‘cancel_rearming_delayed_work’ is deprecated (declared at include/linux/workqueue.h:421)
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch is adding support for Technisat's new USB2.0 DVB-S/S2 receiver
device. The development was sponsored by Technisat.
The Green led is toggle depending on the frontend-state. The Red LED is turned
on all the time.
The MAC address reading from the EEPROM along with the
LRC-method to check whether its valid.
Support for the IR-receiver of the Technisat USB2 box. The keys of
small, black remote-control are built-in, repeated key behaviour are
simulated.
The i2c-mutex of the dvb-usb-structure is used as a general mutex for
USB requests, as there are 3 threads racing for atomic requests
consisting of multiple usb-requests.
A module option is there which disables the toggling of LEDs by the
driver on certain triggers. Useful when being used in a "dark"
environment.
[mchehab@redhat.com: Fix merge conflicts with RC renaming patches]
Signed-off-by: Martin Wilks <m.wilks@technisat.com>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some backends want to receive the full transport stream including
uncorrected packets. To have that feature this patchs add a field to
the config-structure called TEI (transport stream error indicator).
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Martin Wilks <m.wilks@technisat.com>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch STV090X adds and exports a function to control the GPIOs of
the stv090x-devices.
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Martin Wilks <m.wilks@technisat.com>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (64 commits)
Input: tsc2005 - remove 'disable' sysfs attribute
Input: tsc2005 - add open/close
Input: tsc2005 - handle read errors from SPI layer
Input: tsc2005 - do not rearm timer in hardirq handler
Input: tsc2005 - don't use work for 'pen up' handling
Input: tsc2005 - do not use 0 in place of NULL
Input: tsc2005 - use true/false for boolean variables
Input: tsc2005 - hide selftest attribute if we can't reset
Input: tsc2005 - rework driver initialization code
Input: tsc2005 - set up bus type in input device
Input: tsc2005 - set up parent device
Input: tsc2005 - clear driver data after unbinding
Input: tsc2005 - add module description
Input: tsc2005 - remove driver banner message
Input: tsc2005 - remove incorrect module alias
Input: tsc2005 - convert to using dev_pm_ops
Input: tsc2005 - use spi_get/set_drvdata()
Input: introduce tsc2005 driver
Input: xen-kbdfront - move to drivers/input/misc
Input: xen-kbdfront - add grant reference for shared page
...
In commit 567aba0b79, the probe address
for tda8290_probe and tda8295_probe was hard-coded to 0x4b, which is the
default i2c address for those devices, but its possible for the device
to be at an alternate address, 0x42, which is the case for the HVR-1950.
If we probe the wrong address, probe fails and we have a non-working
device. We have the actual address passed into the function by way of
i2c_props, we just need to use it. Also fix up some copy/paste comment
issues and streamline debug spew a touch. Verified to restore my
HVR-1950 to full working order.
Special thanks to Ken Bass for reporting the issue in the first place,
and to both he and Gary Buhrmaster for aiding in debugging and analysis
of the problem.
Reported-by: Ken Bass <kbass@kenbass.com>
Tested-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There's a Realtek combo card reader and IR receiver device with multiple
usb interfaces on it. The mceusb driver is incorrectly grabbing all of
them. This change should make it bind to only interface 2 (patch based
on lsusb output on the linux-media list from Lucian Muresan).
Tested regression-free with the six mceusb devices I have myself.
Reported-by: Patrick Boettcher <pboettcher@kernellabs.com>
Reported-by: Lucian Muresan <lucianm@users.sourceforge.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The CIR Wake FIFO is 67 bytes long, but the stock remote appears to only
populate 65 of them. Limit comparison to 65 bytes, and wake from suspend
works a whole lot better (it wasn't working at all for most folks).
Fix based on comparison with the old lirc_wb677 driver from Nuvoton,
debugging and testing done by Dave Treacy by way of the lirc mailing
list.
Reported-by: Dave Treacy <davetreacy@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The newest variants of the HVR-1600 have an s5h1411/tda18271 for the digital
frontend. Add support for these boards.
Thanks to Hauppauge Computer Works for providing sample hardware.
[awalls@md.metrocast.net: Changed an additional log message to clarify for
the end user that the driver is defaulting to an original HVR-1600 for
unknown model numbers.]
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After upgrading the kernel from stock Ubuntu 7.10 to
10.04, with no hardware changes, I started getting the dreaded DMA
TIMEOUT errors, followed by inability to encode until the machine was
rebooted.
I came across a post from Andy in March
(http://www.gossamer-threads.com/lists/ivtv/users/40943#40943) where he
speculates that perhaps the corrective actions being taken after a DMA
ERROR are not sufficient to recover the situation. After some testing
I suspect that this is indeed the case, and that in fact the corrective
action may be what hangs the card's DMA engine, rather than the
original error.
Specifically these DMA ERROR IRQs seem to present with two different
values in the IVTV_REG_DMASTATUS register: 0x11 and 0x13. The current
corrective action is to clear that status register back to 0x01 or
0x03, and then issue the next DMA request. In the case of a 0x13 this
seems to result in a minor glitch in the encoded stream due to the
failed transfer that was not retried, but otherwise things continue OK.
In the case of a 0x11 the card's DMA write engine is never heard from
again, and a DMA TIMEOUT follows shortly after. 0x11 is the killer.
I suspect that the two cases need to be handled differently. The
difference is in bit 1 (0x02), which is set when the error is about to
be successfully recovered, and clear when things are about to go bad.
Bit 1 of DMASTATUS is described differently in different places either
as a positive "write finished", or an inverted "write busy". If we
take the first definition, then when an error arises with state 0x11,
it means that the write did not complete. It makes sense to start a
new transfer, as in the current code. But if we take the second
definition, then 0x11 means "an error but the write engine is still
busy". Trying to feed it a new transfer in this situation might not be
a good idea.
As an experiment, I added code to ignore the DMA ERROR IRQ if DMASTATUS
is 0x11. I.e., don't start a new transfer, don't clear our flags, etc.
The hope was that the card would complete the transfer and issue a ENC
DMA COMPLETE, either successfully or with an error condition there.
However the card still hung.
The only remaining corrective action being taken with a 0x11 status was
then the write back to the status register to clear the error, i.e.
DMASTATUS = DMASTATUS & ~3. This would have the effect of clearing the
error bit 4, while leaving the lower bits indicating DMA write busy.
Strangely enough, removing this write to the status register solved the
problem! If the DMA ERROR IRQ with DMASTATUS=0x11 is completely
ignored, with no corrective action at all, then the card will complete
the transfer and issue a new IRQ. If the status register is written to
when it has the value 0x11, then the DMA engine hangs. Perhaps it's
illegal to write to
DMASTATUS while the read or write busy bit is set? At any rate, it
appears that the current corrective action is indeed making things
worse rather than better.
I put together a patch that modifies ivtv_irq_dma_err to do the
following:
- Don't write back to IVTV_REG_DMASTATUS.
- If write-busy is asserted, leave the card alone. Just extend the
timeout slightly.
- If write-busy is de-asserted, retry the current transfer.
This has completely fixed my DMA TIMEOUT woes. DMA ERR events still
occur, but now they seem to be correctly handled. 0x11 events no
longer hang the card, and 0x13 events no longer result in a glitch in
the stream, as the failed transfer is retried. I'm happy.
I've inlined the patch below in case it is of interest. As described
above, I have a theory about why it works (based on a different
interpretation of bit 1 of DMASTATUS), but I can't guarantee that my
theory is correct. There may be another explanation, or it may be a
fluke. Maybe ignoring that IRQ entirely would be equally effective?
Maybe the status register read/writeback sequence is race condition if
the card changes it in the mean time? Also as I am using a PVR-150
only, I have not been able to test it on other cards, which may be
especially relevant for 350s that support concurrent decoding.
Hopefully the patch does not break the DMA READ path.
Mike
[awalls@md.metrocast.net: Modified patch to add a verbose comment, make minor
brace reformats, and clear the error flags in the IVTV_REG_DMASTATUS iff both
read and write DMA were not in progress. Mike's conjecture about a race
condition with the writeback is correct; it can confuse the DMA engine.]
[Comment and analysis from the ML post by Michael <mike@rsy.com>]
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix the probing of cx2583x chips, because two controls were clustered
that are not created for these chips.
This regression was introduced in 2.6.36.
Signed-off-by: Sven Barth <pascaldragon@googlemail.com>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The previous revert-commit, that affected cx23885-i2c.c, left some
unused labels that the compiler griped about. Clean them up.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This reverts commit 44835f197b.
With the CX23885 hardware I2C master, checking for I2C slave ACK/NAK
is not valid when the I2C_EXTEND or I2C_NOSTOP bits are set.
Revert the commit that checks for I2C slave ACK/NAK on all transactions,
so that XC5000 tuners work with the CX23885 again.
Thanks go to Mark Zimmerman for reporting and bisecting this problem.
Bisected-by: Mark Zimmerman <markzimm@frii.com>
Reported-by: Mark Zimmerman <markzimm@frii.com>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds the pid filtering for the dib7000M demod. It also
corrects the pid filtering for the dib7700 based board. It should
prevent an oops, when using dib7700p based board.
References: https://bugzilla.novell.com/show_bug.cgi?id=644807
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <patrick.boettcher@dibcom.fr>
Tested-by: Pavel SKARKA <paul.sp@seznam.cz>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the current matching rules the lookup for rc protocol named rc-5-sz matches with "rc-5" before finding "rc-5-sz". Thus one is able to never enable/disable the rc-5-sz protocol via sysfs.
Fix the lookup to require an exact match which allows the manipulation of sz protocol.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Final step to eliminate of_platform_bus_type. They're all just
platform drivers now.
v2: fix type in pasemi_nand.c (thanks to Stephen Rothwell)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'media_fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] fix saa7111 non-detection
[media] rc/streamzap: fix reporting response times
[media] mceusb: really fix remaining keybounce issues
[media] rc: use time unit conversion macros correctly
[media] rc/ir-lirc-codec: add back debug spew
[media] ir-kbd-i2c: improve remote behavior with z8 behind usb
[media] lirc_zilog: z8 on usb doesn't like back-to-back i2c_master_send
[media] hdpvr: fix up i2c device registration
[media] rc/mce: add mappings for missing keys
[media] gspca - zc3xx: Discard the partial frames
[media] gspca - zc3xx: Fix bad images with the sensor hv7131r
[media] gspca - zc3xx: Bad delay when given by a table
au0828: fix VBI handling when in V4L2 streaming mode
It turns up V4L2 streaming mode (a.k.a mmap) was broken for VBI streaming.
This was causing libzvbi to fall back to V4L1 capture mode, and is a blatent
violation of the V4L2 specification.
Make the implementation work properly in this mode.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Changeset 4651918a4a changed the way events
are stored. However, it forgot to fix ir_raw_event_store_edge() to work
with the new way. Due to that, the decoders will likely do bad things.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change for firmware re-loading and updated firmware versions.
Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
video_device is already being freed in video_device.release callback on
release.
Signed-off-by: Pawel Osciak <pawel@osciak.com>
Reported-by: Roland Kletzing <devzero@web.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Driver Version v1.75 Kernel oops appears in 2.6.37-rc8 in
lme_firmware_switch because of a memcpy to a const char.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All users of old style get/setkeycode methids have been converted so
it is time to retire them.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
One saa7111 device is reporting a different ID:
saa7115 0-0024: chip found @ 0x48 (ID 0f7111d0e111111) does not match a known saa711x chip.
As this is for sure a saa7111, change the detection code to also
cover this device.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The streamzap driver has relatively low sampling resolution, and any
delays in reporting events seem to cause some minor problems for the
likes of irw when using the lirc bridge driver, resulting in a single
keypress registering as multiple independent ones, rather than as a
single press with repeats. If we call ir_raw_event_handle() more
frequently and reset the rawir kfifo at end-of-signal, the behavior
improves quite a bit.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make sure rawir struct is zeroed out before populating it for each
ir_raw_event_store_with_filter() call, and when we see a trailing 0x80
packet (end-of-data), issue an ir_raw_event_reset() call.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to my own stupidity, some of the wrong time unit conversion macros
were being used inside some of the IR drivers I've been working on. Fix
that, and convert over some additional places to also use the macros.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some occasionally useful debug spew disappeared as part of a feature
update a while back, and I'm finding myself in need of it again to help
diagnose some issues.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the same "are you ready?" i2c_master_send() poll command to
get_key_haup_xvr found in lirc_zilog, which is apparently seen in
the Windows driver for the PVR-150 w/a z8. This stabilizes what is
received from both the HD-PVR and HVR-1950, even with their polling
intervals at the default of 100, thus the removal of the custom
260ms polling_interval in pvrusb2-i2c-core.c.
Acked-by: Andy Walls <awalls@md.metrocast.net>
Acked-by: Mike Isely <isely@isely.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We have to actually call i2c_new_device() once for each of the rx and tx
addresses. Also improve error-handling and device remove i2c cleanup.
Reviewed-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Per http://mediacenterguides.com/book/export/html/31 and investigation
by Erin, we were missing these last three mappings to complete the mce
key table. Lets remedy that.
Reported-by: Erin Simonds <fisslefink@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In some cases, some frames may not end with the JPEG end of frame.
Being not complete, they are now discarded.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The problem was introduced by the commit 2af0b4c60c.
Some registers were no more initialized.
Tested-by: <Giovanni Scafora giovanni@archlinux.org>
Tested-by: <Sergey Manucharian sm@ingeniware.com>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do not respond with -EINVAL to EVIOCGKEYCODE for not-yet-mapped
scancodes, but rather return KEY_RESERVED.
This fixes breakage with Ubuntu's input-kbd utility that stopped
returning full keymaps for remote controls.
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Mark Lord <kernel@teksavvy.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'media_fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (101 commits)
[media] staging/lirc: fix mem leaks and ptr err usage
[media] hdpvr: reduce latency of i2c read/write w/recycled buffer
[media] hdpvr: enable IR part
[media] rc/mceusb: timeout should be in ns, not us
[media] v4l2-device: fix 'use-after-freed' oops
[media] v4l2-dev: don't memset video_device.dev
[media] zoran: use video_device_alloc instead of kmalloc
[media] w9966: zero device state after a detach
[media] v4l: Fix a use-before-set in the control framework
[media] v4l: Include linux/videodev2.h in media/v4l2-ctrls.h
[media] DocBook/v4l: update V4L2 revision and update copyright years
[media] DocBook/v4l: fix validation error in dev-rds.xml
[media] v4l2-ctrls: queryctrl shouldn't attempt to replace V4L2_CID_PRIVATE_BASE IDs
[media] v4l2-ctrls: fix missing 'read-only' check
[media] pvrusb2: Provide more information about IR units to lirc_zilog and ir-kbd-i2c
[media] ir-kbd-i2c: Add back defaults setting for Zilog Z8's at addr 0x71
[media] lirc_zilog: Update TODO.lirc_zilog
[media] lirc_zilog: Add Andy Walls to copyright notice and authors list
[media] lirc_zilog: Remove useless struct i2c_driver.command function
[media] lirc_zilog: Remove unneeded tests for existence of the IR Tx function
...
The meaning of CONFIG_EMBEDDED has long since been obsoleted; the option
is used to configure any non-standard kernel with a much larger scope than
only small devices.
This patch renames the option to CONFIG_EXPERT in init/Kconfig and fixes
references to the option throughout the kernel. A new CONFIG_EMBEDDED
option is added that automatically selects CONFIG_EXPERT when enabled and
can be used in the future to isolate options that should only be
considered for embedded systems (RISC architectures, SLOB, etc).
Calling the option "EXPERT" more accurately represents its intention: only
expert users who understand the impact of the configuration changes they
are making should enable it.
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: David Woodhouse <david.woodhouse@intel.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Greg KH <gregkh@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Robin Holt <holt@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current hdpvr code kmalloc's a new buffer for every i2c read and
write. Rather than do that, lets allocate a buffer in the driver's
device struct and just use that every time.
The size I've chosen for the buffer is the maximum size I could
ascertain might be used by either ir-kbd-i2c or lirc_zilog, plus a bit
of padding (lirc_zilog may use up to 100 bytes on tx, rounded that up
to 128).
Note that this might also remedy user reports of very sluggish behavior
of IR receive with hdpvr hardware.
v2: make sure (len <= (dev->i2c_buf)) [Jean Delvare]
Reported-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A number of things going on here, but the end result is that the IR part
on the hdpvr gets enabled, and can be used with ir-kbd-i2c and/or
lirc_zilog.
First up, there are some conditional build fixes that come into play
whether i2c is built-in or modular. Second, we're swapping out
i2c_new_probed_device() for i2c_new_device(), as in my testing, probing
always fails, but we *know* that all hdpvr devices have a z8 chip at
0x70 and 0x71. Third, we're poking at an i2c address directly without a
client, and writing some magic bits to actually turn on this IR part
(this could use some improvement in the future). Fourth, some of the
i2c_adapter storage has been reworked, as the existing implementation
used to lead to an oops following i2c changes c. 2.6.31.
Earlier editions of this patch have been floating around the 'net for a
while, including being patched into Fedora kernels, and they *do* work.
This specific version isn't yet tested, beyond loading ir-kbd-i2c and
confirming that it does bind to the RX address of the hdpvr.
[mchehab@redhat.com: I2C_CLASS_TV_ANALOG is not defined. Fix compilation bug]
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes an egregious bug in mceusb driver, where the receiver was being
put into idle mode far sooner than it should have, thanks to storing a
timeout value that in us where it should be ns. Basically, the receiver
kept going into idle mode before a trailing space had been fully
received, which was causing problems for some protocols, most notably
manifesting as lirc userspace never receiving a trailing space for any
rc5 signals.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix a bug in v4l2_device_unregister where the sd pointer can be dereferenced
after it was freed.
Normally the i2c adapter is removed before this function is called. Removing
the adapter will also unregister all subdevs on that adapter, so generally
v4l2_device_unregister has nothing to do. However, in the case of a platform
i2c bus that bus is generally not freed.
In that case, after freeing the i2c subdevice the code will fall into the
second block when it tests if the subdev is a SPI device. But by that time
the subdev is already freed and the kernel oopses.
The fix is trivial: continue with the loop after freeing the i2c or spi
subdevice.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reported-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Zeroing video_device.dev causes a memory leak if video_set_drvdata
was called before video_register_device was called. video_set_drvdata
calls dev_set_drvdata which allocates video_device.dev.p.
memsetting this will prevent freeing of that memory.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After a detach zero the whole device state to ensure a clean slate
on the next attach.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2_queryctrl sets the step value based on the control type. That would
be fine if it used the control type stored in the V4L2 kernel control
object, not the one stored in the userspace ioctl structure that has
just been memset to 0. Fix this.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When queryctrl is called with a V4L2_CID_PRIVATE_BASE control ID, then
currently it is replaced by the real internal ID. This is not according to
the spec so keep the V4L2_CID_PRIVATE_BASE ID in this case.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
VIDIOC_S_CTRL did not check against read-only controls. Even worse, for
controls of type CTRL_CLASS it would cause a kernel oops since those controls
do not have a s_ctrl op.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When registering an IR Rx device with the I2C subsystem, provide more detailed
information about the IR device and default remote configuration for the IR
driver modules.
Also explicitly register any IR Tx device with the I2C subsystem.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This reverts a portion of commit
44243fc2ef
A commit for which I errantly recommended that defaults for I2C address
0x71 not be set by ir-kbd-i2c.c
The pvrusb2 and bttv drivers currently rely on ir-kbd-i2c setting
defaults for that address. Until I can get those bridge drivers fixed
to properly send IR_i2c_init_data for boards with Zilog Z8 chips,
just add back the default settings for I2C address 0x71.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After a recent update of xf86-input-evdev and xorg-server, I noticed
that X11 applications did not receive keypresses from the FireDTV
infrared remote control anymore. Instead, the Xorg log featured lots of
"FireDTV remote control: dropping event due to full queue!"
exclamations. The Linux console did not have an issue with the
FireDTV's RC though.
The fix is to insert EV_SYN events after the key-down/-up events.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit e3c9221519 ("[media] radio-aimslab.c: Fix
gcc 4.5+ bug") removed the include, but introduced new callers of msleep():
| drivers/media/radio/radio-aimslab.c: In function ‘rt_decvol’:
| drivers/media/radio/radio-aimslab.c:76: error: implicit declaration of function ‘msleep’
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix sparse warning for non-ANSI function declaration:
drivers/media/rc/ir-raw.c:247:30: warning: non-ANSI function declaration of function 'ir_raw_get_allowed_protocols'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds s_power support to adv7175 driver. Power-down is done
by power-down all four DACs.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
info->num comes from the user. It's type int. If the user passes
in a negative value that would cause memory corruption.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
My initial thinking was that we should default to mouse mode, so people
could use the mouse function to click on something on a login screen,
but a lot of systems where a remote is useful automatically log in a
user and launch a media center application, some of which hide the
mouse, which can be confusing to users if they punch buttons on the
remote and don't see any feedback. Plus, first and foremost, its a
remote, so lets default to being a remote, and only toggle into mouse
mode when the user explicitly asks for it. As a nice side-effect, this
actually simplifies some of the code a fair bit...
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ene_ir driver was using a private define of MS_TO_NS, which is meant
to be microseconds to nanoseconds. The mceusb driver copied it,
intending to use is a milliseconds to microseconds. Lets move the
defines to a common location, expand and standardize them a touch, so
that we now have:
MS_TO_NS - milliseconds to nanoseconds
MS_TO_US - milliseconds to microseconds
US_TO_NS - microseconds to nanoseconds
Reported-by: David Härdeman <david@hardeman.nu>
CC: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Otherwise, we have a null receive buffer, and the logic all falls down,
goes boom, all ffdc devs wind up as imon IR w/VFD. Oops.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
dev->rdev is accessed in ene_setup_hw_settings, so it needs to be wired
up before then.
[Jarod Wilson]: Also fix a possible improper resource freeing bug while
we're looking at possible probe issues here.
Signed-off-by: Kyle McMartin <kmcmartin@redhat.com>
CC: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There's a nasty bug that slipped in when the rc device interface was
altered, only affecting the older 0xffdc imon devices. We were trying
to access ictx->rdev->allowed_protos before ictx->rdev had been set.
There's also an issue with call ordering that meant the correct
keymap wasn't getting loaded for MCE IR type 0xffdc devices.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use unlocked_ioctl in v4l2_file_operations. The locking is
already in place.
Signed-off-by: Matti J. Aaltonen <matti.j.aaltonen@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With cmwq, there's no reason to use separate out_work_queue. Drop it
and use system_wq instead. The in_work_queue needs to be ordered so
can't use one of the system wqs; however, as it isn't used to reclaim
memory, allocate the workqueue with alloc_ordered_workqueue() without
WQ_MEM_RECLAIM.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Andy Walls <awalls@md.metrocast.net>
Acked-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hi,
While reading
drivers/media/video/tlg2300/pd-video.c::alloc_bulk_urbs_generic() I
noticed that
- We don't free the memory allocated to 'urb' if the call to
usb_alloc_coherent() fails.
- If the 'num' argument to the function is ever <= 0 we'll return an
uninitialized variable 'i' to the caller.
The following patch addresses both of the above by a) calling
usb_free_urb() when usb_alloc_coherent() fails and by explicitly
initializing 'i' to zero.
I also moved the variables 'mem' and 'urb' inside the for loop. This does
not actually make any difference, it just seemed more correct to me to let
variables exist only in the innermost scope they are used.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We may leak the storage allocated to 'state' in
drivers/media/dvb/frontends/ix2505v.c::ix2505v_attach() on error, as
it is too early to be able to call ix2505v_release().
This patch makes sure we free the allocated memory in the failure case.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The infrared was set by sensor write instead of bridge GPIO.
It is now settable by the standard control ILLUMINATOR_1.
A module parameter permits to set the right GPIO bit according
to the StarCam model.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
__devinit* must not be used in USB drivers.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Renamed has_new to is_new.
Drivers can use the is_new field to determine if a new value was specified
for a control. The v4l2_ctrl_handler_setup() must always set this to 1 since
the setup has to force a full update of all controls.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some subdevs need to call into the board code after they are registered
and have a valid struct v4l2_device pointer. The s_config op was abused
for this, but now that it is removed we need a cleaner way of solving this.
So this patch adds a struct with internal ops that the v4l2 core can call.
Currently only two ops exist: register and unregister. Subdevs can implement
these to call the board code and pass it the v4l2_device pointer, which the
board code can then use to get access to the struct that embeds the
v4l2_device.
It is expected that in the future open and close ops will also be added.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The core.s_config op was meant for legacy drivers that needed to work with old
pre-2.6.26 kernels. This is no longer relevant. Unfortunately, this op was
incorrectly called from several drivers.
Replace those occurences with proper i2c_board_info structs and call
v4l2_i2c_new_subdev_board.
After these changes v4l2_i2c_new_subdev_cfg() was no longer used, so remove
that function as well.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are some weird bugs at tda8290/tda18271 initialization, as it
insits do do analog initialization during DVB frontend attach:
DVB: registering new adapter (saa7133[0])
DVB: registering adapter 0 frontend 0 (Fujitsu mb86A20s)...
mb86a20s: mb86a20s_initfe
tda18271_write_regs: [2-0060|M] ERROR: idx = 0x5, len = 1, i2c_transfer returned: -5
tda18271_init: [2-0060|M] error -5 on line 830
tda18271_tune: [2-0060|M] error -5 on line 908
tda18271_write_regs
tda18271_write_regs: [2-0060|M] ERROR: idx = 0x5, len = 1, i2c_transfer returned: -5
tda18271c2_rf_tracking_filters_correction: [2-0060|M] error -5 on line 265
tda18271_write_regs
tda18271_write_regs: [2-0060|M] ERROR: idx = 0x25, len = 1, i2c_transfer returned: -5
tda18271_channel_configuration: [2-0060|M] error -5 on line 119
tda18271_set_analog_params: [2-0060|M] error -5 on line 1045
tda18271_set_analog_params: [2-0060|M] error -5 on line 1045
tda829x 2-004b: tda8295 not locked, no signal?
tda829x 2-004b: tda8295_i2c_bridge: disable i2c gate
tda829x 2-004b: tda8295 not locked, no signal?
tda829x 2-004b: tda8295_i2c_bridge: disable i2c gate
mb86a20s_i2c_writereg: writereg error (rc == -5, reg == 0x29, data == 0x33)
mb86a20s: Init failed. Will try again later
The problem is that mb86a20s is only visible if the analog part is disabled.
However, due to a trick at mb86a20s, it will later initialize properly:
mb86a20s: mb86a20s_initfe: Initialization succeded.
This is hacky and ugly. However, I coldn't find any easy way to fix it.
A proper fix would be to have a resource locking schema, used by both
V4L and DVB parts that would block access to analog registers while
digital registers are in use, but this will probably put tda829x into
a dead lock.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
