tty_unlock is used on all other exits from the function.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MDIO_REG_ADDR_MASK is already applied in function
atl1c_write_phy_reg and atl1c_read_phy_reg
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
l2cb 1.1 hardware has a bug for magic wakeup,
the workaround is to add pattern enable.
WoL related registers are refined as well.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bit PCIE_PHYMISC_FORCE_RCV_DET is only for l1c&l2c to fix WoL issue,
other chips set bit5 of REG_MASTER_CTRL --- this way could save more
power than the former, and the bit should be kept all time.
l2cb 1.x has special setting for L0S/L1
l2cb 1.x & l1d 1.x should clear Vendor Message on some platforms,
otherwise it will cause the root complex hang.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
some platforms(BIOS or OS) may change ASPM configuration in
PCI Express Link Control Register directly and dynamically
regardless the device driver installation.
Checking if ASPM support during the driver init phase by reading
PCI Express Link Contrl Register doesn't make sense.
This refine/update assume L0S/L1 is defalut enabled as hw->ctrl_flags
inited. atl1c_set_aspm will set real configuration based on chip
capability to hardware register.
atl1c_disable_l0s_l1 and register definition of REG_PM_CTRL are
refined as well.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bit MASTER_CTRL_CLK_SEL_DIS could be set before enter suspend
clear it after resume to enable pclk(PCIE clock) switch to
low frequency(25M) in some circumstances to save power.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refine/update register REG_MASTER_CTRL definition according with
hardware spec.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clear PCIE error status (error log is write-1-clear).
REG_PCIE_UC_SEVERITY is removed as it's a standard pcie register,
and using kernle API to access it.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dmar_dly_cnt and dmaw_dly_cnt aren't used by hardware/driver any more.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
atl1c_configure_tx used a wrong value of MAX_TX_OFFLOAD_THRESH(9KB)
for TSO threshold.
the right value should be 7KB
Fast Ethernet controller doesn't support Jumbo frame.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
l1c_wait_until_idle is called for serval modules (TXQ/RXQ/TXMAC/RXMAC).
specific moudle have specific idle/busy status in reg REG_IDLE_STATUS.
the previous code return wrongly if all modules are in idle status,
regardless the 'stop' action is applied on individual module.
Refine the reg REG_IDLE_STATUS definition as well.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
threshold setting to control ASPM for diff chips are different.
currently, all gigabit-capability chips have limited-ASPM under
100M throughput.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Tested-by: Liu David <dwliu@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some platforms, for example where we are doing the bring-up,
the csr clock is not passed from the framework and the Ethernet
device driver is failing when it can work w/o any issues and
using the default values. So this patch just warnings the case
of the csr clock cannot be acquired but w/o failing the probe
step. I have just tested it on ST STiH415 SoC (ARM).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently the dma parameters that can be passed from the platform
have been moved from the plat_stmmacenet_data to the stmmac_dma_cfg.
In case of this new structure is not well allocated the driver can
fails. This is an example how this field is managed in ST platforms
static struct stmmac_dma_cfg gmac_dma_setting = {
.pbl = 32,
};
static struct plat_stmmacenet_data stih415_ethernet_platform_data[] = {
{
.dma_cfg = &gmac_dma_setting,
.has_gmac = 1,
[snip]
This patch so verifies that the dma_cfg passed from the platform.
In case of it is NULL there is no reason that the driver has to fail
and some default values can be passed. These are ok for all the
Synopsys chips and could impact on performances, only.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
cc: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the mdio_register/_unregister in probe/remove
functions and this also is required when hibernation on disk
is done.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st,com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st,com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Freeze and restore can call the custom init/exit functions.
Also the patch adds a custom data field that can be used
for storing platform data useful on restore the embedded
setup (e.g. GPIO, SYSCFG).
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull nfsd bugfixes from J. Bruce Fields:
"One bugfix, and one minor header fix from Jeff Layton while we're
here"
* 'for-3.4' of git://linux-nfs.org/~bfields/linux:
nfsd: include cld.h in the headers_install target
nfsd: don't fail unchecked creates of non-special files
Remove declaration of iwl_alloc_traffic_mem from iwl-agn.h,
from methods that was exposed to support MVM.
MVM doesn't have to use this declaration.
CC: netdev@vger.kernel.org
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also fix issue of accessing invalid msgr pointer issue. The local
msgr pointer in fucntion mpic_msgr_get will be accessed before
getting a valid address which will cause kernel crash.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In file included from arch/powerpc/sysdev/mpic_msgr.c:20:0:
~/arch/powerpc/include/asm/mpic_msgr.h: In function 'mpic_msgr_set_destination':
~/arch/powerpc/include/asm/mpic_msgr.h:117:2:
error: implicit declaration of function 'get_hard_smp_processor_id'
make[1]: *** [arch/powerpc/sysdev/mpic_msgr.o] Error 1
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Commit ae3a197e (Disintegrate asm/system.h for PowerPC) broke build of
assembly files when CONFIG_BOOKE_WDT is enabled as follows:
AS arch/powerpc/lib/string.o
/home/baruch/git/stable/arch/powerpc/include/asm/reg_booke.h: Assembler messages:
/home/baruch/git/stable/arch/powerpc/include/asm/reg_booke.h:19: Error: Unrecognized opcode: `extern'
/home/baruch/git/stable/arch/powerpc/include/asm/reg_booke.h:20: Error: Unrecognized opcode: `extern'
Since setup_32.c is the only user of the booke_wdt configuration variables, move
the declarations there.
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Enhances command validation done by TIPC's configuration service so
that it works properly even if the node's network address is changed in
mid-operation. The default node address of <0.0.0> is now recognized as an
alias for "this node" even after a new network address has been assigned.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Revises handling of a rejected message to ensure that a locally
originated message is returned properly even if the node's network
address is changed in mid-operation. The routine now treats the
default node address of <0.0.0> as an alias for "this node" when
determining where to send a returned message.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Revises handling of send routines for payload messages to ensure that
they are processed properly even if the node's network address is
changed in mid-operation. The routines now treat the default node
address of <0.0.0> as an alias for "this node" when determining where
to send an outgoing message.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
There are two send routines that might conceivably be asked by an
application to send a message off-node when the node is still using
the default network address. These now have an added check that
detects this and rejects the message gracefully.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The routine that changes the node's network address now takes TIPC's
network lock in write mode while the main address variable and associated
data structures are being changed; this is needed to ensure that the
link subsystem won't attempt to send a message off-node until the sending
port's message header template has been updated with the node's new
network address.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Revises routines that deal with connections between two ports on
the same node to ensure the connection is not impacted if the node's
network address is changed in mid-operation. The routines now treat
the default node address of <0.0.0> as an alias for "this node" in
the following situations:
1) Incoming messages destined to a connected port now handle the alias
properly when validating that the message was sent by the expected
peer port, ensuring that the message will be accepted regardless of
whether it specifies the node's old network address or it's current one.
2) The code which completes connection establishment now handles the
alias properly when determining if the peer port is on the same node
as the connected port.
An added benefit of addressing issue 1) is that some peer port
validation code has been relocated to TIPC's socket subsystem, which
means that validation is no longer done twice when a message is
sent to a non-socket port (such as TIPC's configuration service or
network topology service).
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Prior to commit 23dd4cce38
"tipc: Combine port structure with tipc_port structure"
there was a need for the two sets of helper functions. But
now they are just duplicates. Remove the globally visible
ones, and mark the remaining ones as inline.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Re-orders port creation logic so that the initialization of a new
port's message header template occurs while the port list lock is
held. This ensures that a change to the node's network address that
occurs at the same time as the port is being created does not result
in the template identifying the sender using the former network
address. The new approach guarantees that the new port's template is
using the current network address or that it will be updated when
the address changes.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Removes an unnecessary check in the logic that updates the message
header template for existing ports when a node's network address is
first assigned. There is no longer any need to check to see if the
node's network address has actually changed since the calling routine
has already verified that this is so.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Revises routines that add and remove an entry from a node's name table
so that the publication scope lists are updated properly even if the
node's network address is changed in mid-operation. The routines now
recognize the default node address of <0.0.0> as an alias for "this node"
even after a new network address has been assigned.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Introduces routines that test whether a given network address is
equal to a node's own network address or if it lies within the node's
own network cluster, and which work properly regardless of whether
the node is using the default network address <0.0.0> or a non-zero
network address that is assigned later on. In essence, these routines
ensure that address <0.0.0> is treated as an alias for "this node",
regardless of which network address the node is actually using.
Old users of the pre-existing more strict match in_own_cluster()
have been accordingly redirected to what is now called
in_own_cluster_exact() --- which does not extend matching to <0,0,0>.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
No longer increments counter of number of publications by a node
if an attempt to add a new publication fails. This prevents TIPC from
incorrectly blocking future publications because the configured maximum
number of publications has been reached.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Ensures that node-scope name publications that exist prior to the
configuration of a node's network address are properly re-initialized
with that address when it is assigned. TIPC's node-scope publications
are now tracked using a publications list like the lists used for
cluster-scope and zone-scope publications so they can be easily updated
when required.
The inclusion of node scope name publications in a conventional publication
list means that they must now also be withdrawn, just like cluster and zone
scope publications are currently withdrawn. So some conditional tests on
scope ==/!= TIPC_NODE_SCOPE are inserted/removed accordingly.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Utilizes distinct lists to track zone-scope and cluster-scope names
published by a node. For now, TIPC continues to process the entries
in both lists in the same way; however, an upcoming patch will utilize
the existence of the lists to prevent the sending of cluster-scope names
to nodes that are not part of the local cluster.
To achieve this, an array of publication lists is introduced, so
that they can be iterated over and accessed via publ->scope as
an index where convenient.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Commit 46d026ac ("powerpc/85xx: consolidate of_platform_bus_probe calls")
replaced platform-specific of_device_id tables with a single function
that probes the most of the busses in 85xx device trees. If a specific
platform needed additional busses probed, then it could call
of_platform_bus_probe() again. Typically, the additional platform-specific
busses are children of existing busses that have already been probed.
of_platform_bus_probe() does not handle those child busses automatically.
Unfortunately, this doesn't actually work. The second (platform-specific)
call to of_platform_bus_probe() never finds any of the busses it's asked
to find.
To remedy this, the platform-specific of_device_id tables are eliminated,
and their entries are merged into mpc85xx_common_ids[], so that all busses
are probed at once.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
While reviewing the sysctl code in ax25 I spotted races in ax25_exit
where it is possible to receive notifications and packets after already
freeing up some of the data structures needed to process those
notifications and updates.
Call unregister_netdevice_notifier early so that the rest of the cleanup
code does not need to deal with network devices. This takes advantage
of my recent enhancement to unregister_netdevice_notifier to send
unregister notifications of all network devices that are current
registered.
Move the unregistration for packet types, socket types and protocol
types before we cleanup any of the ax25 data structures to remove the
possibilities of other races.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes and adds the irq handler for the
IC+ 101A/G where we need to read the reg17 to clean
the irq.
Also remove the flag for the 1001LF where no interrupt
can be used for this device.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MC77xx devices can operate in two modes: "Direct IP" or "QMI",
switchable using a password protected AT command. Both product ID
and USB interface configuration will change when switched.
The "sierra_net" driver supports the "Direct IP" mode. This driver
supports the "QMI" mode.
There are also multiple possible USB interface configurations in each
mode, some providing more than one wwan interface. Like many other
devices made for Windows, different interface types are identified
using a static interface number. We define a Sierra specific
interface whitelist to support this.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize slave device link state as down if ARP monitor is
active and net_carrier_ok() returns zero. Also shift initial
value of its last_arp_tx so that it doesn't immediately cause
fake detection of "up" state.
When ARP monitoring is used, initializing the slave device with
up link state can cause ARP monitor to detect link failure
before the device is really up (with igb driver, this can take
more than two seconds).
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sp_pri_to_cos[] array size depends on the config but lets say it is
BX_E3B0_MAX_NUM_COS_PORT0 and max_num_of_cos is also
DCBX_E3B0_MAX_NUM_COS_PORT0. In the original code
"pri == max_num_of_cos" was accepted but it is one past the end of the
array.
Also we used "pri" before capping it. It's a harmless read past the end
of the array, but it would affect which error message gets printed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put use & mask on same location to avoid two holes on 64bit arches
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than loading firmware specific for the xtal frequency, just use
the standard firmware and set the xtal frequency after firmware upload.
The modified firmware will never be released, so we're better off
merging this now rather than waiting for v3.5.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
linux/drivers/xen/manage.c: In function 'do_suspend':
linux/drivers/xen/manage.c:160:5: warning: 'si.cancelled' may be used uninitialized in this function
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Pull drm fixes from Dave Airlie:
"It's like a grab bag of one liners:
- core: fix page flip error path, reorder object teardown.
- usb: fix the drm_usb module license.
- i915: VT switch on SNB with non-native modes fix, and a regression
fix from 3.3.
- radeon: missing unreserve on SI, AGP/VRAM setup fix (fixes radeon on
IA64, but its a generic bug), an rn50 regression from 3.3, turn off
MSIs on rv515 (it loses rearms every so often)."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
nouveau: Set special lane map for the right chipset
drm/radeon: fix load detect on rn50 with hardcoded EDIDs.
drm: Releasing FBs before releasing GEM objects during drm_release
drm/nouveau/pm: don't read/write beyond end of stack buffer
drivers: gpu: drm: gma500: mdfld_dsi_output.h: Remove not unneeded include of version.h
radeon: fix r600/agp when vram is after AGP (v3)
drm: fix page_flip error handling
drm/radeon/kms: fix the regression of DVI connector check
drm/usb: fix module license on drm/usb layer.
drm/i915: Do not set "Enable Panel Fitter" on SNB pageflips
drm/i915: Hold mode_config lock whilst changing mode for lastclose()
drm/radeon/si: add missing radeon_bo_unreserve in si_rlc_init() v2
drm/radeon: disable MSI on RV515
drm/i915: don't clobber the special upscaling lvds timings
Fix the following compilation failure:
linux-2.6/drivers/media/video/mt9m032.c: In function '__mt9m032_get_pad_crop':
linux-2.6/drivers/media/video/mt9m032.c:337: error: implicit declaration of function 'v4l2_subdev_get_try_crop'
linux-2.6/drivers/media/video/mt9m032.c:337: warning: return makes pointer from integer without a cast
linux-2.6/drivers/media/video/mt9m032.c: In function '__mt9m032_get_pad_format':
linux-2.6/drivers/media/video/mt9m032.c:359: error: implicit declaration of function 'v4l2_subdev_get_try_format'
linux-2.6/drivers/media/video/mt9m032.c:359: warning: return makes pointer from integer without a cast
linux-2.6/drivers/media/video/mt9m032.c: In function 'mt9m032_probe':
linux-2.6/drivers/media/video/mt9m032.c:767: error: 'struct v4l2_subdev' has no member named 'entity'
linux-2.6/drivers/media/video/mt9m032.c:826: error: 'struct v4l2_subdev' has no member named 'entity'
linux-2.6/drivers/media/video/mt9m032.c: In function 'mt9m032_remove':
linux-2.6/drivers/media/video/mt9m032.c:842: error: 'struct v4l2_subdev' has no member named 'entity'
make[4]: *** [drivers/media/video/mt9m032.o] Error 1
by adding a dependency on VIDEO_V4L2_SUBDEV_API.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This reverts commit 9f85550347.
Peter Zijlstra says:
| Argh, how did that ever make it upstream, please drop.
|
| Russell, please make that go away upstream.
|
| Like I said, this is both completely the wrong way to solve, and you're
| so not paying attention, see:
|
| 5fbd036b55
| 2baab4e904
| e3831edd59
|
| What's even worse:
|
| git describe --contains 9f85550347 --match "v*"
| v3.4-rc3~1^2~3
|
| that nonsense got merged long after those other commits.
Linus Walleij says:
| My bad, was because the initial patch was submitted march 9th before
| these fixes were merged:
| http://marc.info/?l=linux-arm-kernel&m=133159655513844&w=2
|
| It was pending for a while in Russell's patch tracker and I
| rebased it to -rc2 without paying enough attention to recent
| related scheduler fixes ... lesson learned.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When defragmentation is finalized, we clone a packet and kfree_skb() it.
Call consume_skb() to not confuse dropwatch, since its not a drop.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
