Timers on Versatile Express mainboard are used as system clock/event
sources. Driver assumes that they are clocked with 1MHz signal.
Old V2M firmware apparently configured it by default, but on newer
boards one can observe that "sleep 1" command takes over 30 seconds
to finish, as the timers are fed with 32kHz instead...
This patch performs required magic and also removes code clearing
timer's control registers, as exactly the same operations are
performed by the timer driver few jiffies later.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a sched_clock() implementation to Versatile Express using the new
sched_clock() infrastructure for extending 32bit counters to full
64-bit nanoseconds.
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
factorise some generic infrastructure to assist looking up struct clks
for the ARM & SH architecture.
as the code is identical at 99%
put the arch specific code for allocation as example in asm/clkdev.h
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: Rob Herring <rob.herring@smooth-stone.com>
The timer-sp h/w used on versatile platforms can also be used for other
platforms, so move it to a common location.
Signed-off-by: Rob Herring <rob.herring@smooth-stone.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
WARNING: vmlinux.o(.text+0xbf30): Section mismatch in reference from the function v2m_timer_init() to the function .init.text:sp804_clocksource_init()
The function v2m_timer_init() references
the function __init sp804_clocksource_init().
This is often because v2m_timer_init lacks a __init
annotation or the annotation of sp804_clocksource_init is wrong.
WARNING: vmlinux.o(.text+0xbf3c): Section mismatch in reference from the function v2m_timer_init() to the function .init.text:sp804_clockevents_init()
The function v2m_timer_init() references
the function __init sp804_clockevents_init().
This is often because v2m_timer_init lacks a __init
annotation or the annotation of sp804_clockevents_init is wrong.
WARNING: vmlinux.o(.text+0xc524): Section mismatch in reference from the function ct_ca9x4_init() to the function .init.text:l2x0_init()
The function ct_ca9x4_init() references
the function __init l2x0_init().
This is often because ct_ca9x4_init lacks a __init
annotation or the annotation of l2x0_init is wrong.
WARNING: vmlinux.o(.text+0xc530): Section mismatch in reference from the function ct_ca9x4_init() to the function .init.text:clkdev_add_table()
The function ct_ca9x4_init() references
the function __init clkdev_add_table().
This is often because ct_ca9x4_init lacks a __init
annotation or the annotation of clkdev_add_table is wrong.
WARNING: vmlinux.o(.text+0xc578): Section mismatch in reference from the function ct_ca9x4_init() to the (unknown reference) .init.data:(unknown)
The function ct_ca9x4_init() references
the (unknown reference) __initdata (unknown).
This is often because ct_ca9x4_init lacks a __initdata
annotation or the annotation of (unknown) is wrong.
Fix these by making ct_ca9x4_init() and v2m_timer_init() both __init.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (291 commits)
ARM: AMBA: Add pclk support to AMBA bus infrastructure
ARM: 6278/2: fix regression in RealView after the introduction of pclk
ARM: 6277/1: mach-shmobile: Allow users to select HZ, default to 128
ARM: 6276/1: mach-shmobile: remove duplicate NR_IRQS_LEGACY
ARM: 6246/1: mmci: support larger MMCIDATALENGTH register
ARM: 6245/1: mmci: enable hardware flow control on Ux500 variants
ARM: 6244/1: mmci: add variant data and default MCICLOCK support
ARM: 6243/1: mmci: pass power_mode to the translate_vdd callback
ARM: 6274/1: add global control registers definition header file for nuc900
mx2_camera: fix type of dma buffer virtual address pointer
mx2_camera: Add soc_camera support for i.MX25/i.MX27
arm/imx/gpio: add spinlock protection
ARM: Add support for the LPC32XX arch
ARM: LPC32XX: Arch config menu supoport and makefiles
ARM: LPC32XX: Phytec 3250 platform support
ARM: LPC32XX: Misc support functions
ARM: LPC32XX: Serial support code
ARM: LPC32XX: System suspend support
ARM: LPC32XX: GPIO, timer, and IRQ drivers
ARM: LPC32XX: Clock driver
...
The MMC card detection sense has become really confused with negations
at various levels, leading to some platforms not detecting inserted
cards. Fix this by converting everything to positive logic throughout,
thereby getting rid of these negations.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a dummy clk definition for the APB pclk signal on all platforms
using the AMBA bus infrastructure. This ensures that these platforms
continue to work when the core amba bus code controls the APB pclk.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
