Pstore only supports one backend at a time. The preferred
pstore backend is set by passing the pstore.backend=<name>
argument to the kernel at boot time. Currently, while trying
to register with pstore, nvram throws an error message even
when "pstore.backend != nvram", which is unnecessary. This
patch removes the error message in case "pstore.backend != nvram".
Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
userspace programs using cxl currently have to use two strategies for
dealing with MMIO errors simultaneously. They have to check every read
for a return of all Fs in case the adapter has gone away and the kernel
has not yet noticed, and they have to deal with SIGBUS in case the
kernel has already noticed, invalidated the mapping and marked the
context as failed.
In order to simplify things, this patch adds an alternative approach
where the kernel will return a page filled with Fs instead of delivering
a SIGBUS. This allows userspace to only need to deal with one of these
two error paths, and is intended for use in libraries that use cxl
transparently and may not be able to safely install a signal handler.
This approach will only work if certain constraints are met. Namely, if
the application is both reading and writing to an address in the problem
state area it cannot assume that a non-FF read is OK, as it may just be
reading out a value it has previously written. Further - since only one
page is used per context a write to a given offset would be visible when
reading the same offset from a different page in the mapping (this only
applies within a single context, not between contexts).
An application could deal with this by e.g. making sure it also reads
from a read-only offset after any reads to a read/write offset.
Due to these constraints, this functionality must be explicitly
requested by userspace when starting the context by passing in the
CXL_START_WORK_ERR_FF flag.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The patch was generated using fixed coccinelle semantic patch
scripts/coccinelle/api/memdup.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2014320
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The patch was generated using fixed coccinelle semantic patch
scripts/coccinelle/api/memdup.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2014320
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
pcibios_set_pcie_reset_state() could be called to complete
reset request when passing through PCI device, flag
EEH_PE_ISOLATED is set before saving the PCI config sapce.
On some Broadcom adapters, EEH_PE_CFG_BLOCKED is automatically
set when the flag EEH_PE_ISOLATED is marked. It caused bogus
data saved from the PCI config space, which will be restored
to the PCI adapter after the reset. Eventually, the hardware
can't work with corrupted data in PCI config space.
The patch fixes the issue with eeh_pe_state_mark_no_cfg(), which
doesn't set EEH_PE_CFG_BLOCKED when seeing EEH_PE_ISOLATED on the
PE, in order to avoid the bogus data saved and restored to the PCI
config space.
Reported-by: Rajanikanth H. Adaveeshaiah <rajanikanth.ha@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This adds include/uapi/asm/eeh.h to kbuild so that the header
file will be exported automatically with below command. The
header file was added by commit ed3e81ff20 ("powerpc/eeh: Move PE
state constants around")
make INSTALL_HDR_PATH=/tmp/headers \
SRCARCH=powerpc headers_install
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
A working rtc kernel driver is needed so that hwclock can synchronize
system clock to rtc during shutdown/boot. We already have a powernv
platform rtc driver located at drivers/rtc/rtc-opal.c. However it depends
on CONFIG_RTC_CLASS which is disabled by default. Hence the driver isn't
enabled and not compiled for the powernv kernel.
We fix this by enabling rtc class support in pseries defconfig which
enables this driver and compiles it into the pseries kernel. In case
CONFIG_PPC_POWERNV is not enabled we fallback to 'Generic RTC support'
driver which emulates the legacy 'PC RTC driver'.
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In some situations, a NUMA guest that supports
ibm,dynamic-memory-reconfiguration node will end up having flat NUMA
distances between nodes. This is because of two problems in the
current code.
1) Different representations of associativity lists.
There is an assumption about the associativity list in
initialize_distance_lookup_table(). Associativity list has two forms:
a) [cpu,memory]@x/ibm,associativity has following
format:
<N> <N integers>
b) ibm,dynamic-reconfiguration-memory/ibm,associativity-lookup-arrays
<M> <N> <M associativity lists each having N integers>
M = the number of associativity lists
N = the number of entries per associativity list
Fix initialize_distance_lookup_table() so that it does not assume
"case a". And update the caller to skip the length field before
sending the associativity list.
2) Distance table not getting updated from drconf path.
Node distance table will not get initialized in certain cases as
ibm,dynamic-reconfiguration-memory path does not initialize the
lookup table.
Call initialize_distance_lookup_table() from drconf path with
appropriate associativity list.
Reported-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Acked-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Simplify the dma_get_required_mask call chain by moving it from pnv_phb to
pci_controller_ops, similar to commit 763d2d8df1 ("powerpc/powernv:
Move dma_set_mask from pnv_phb to pci_controller_ops").
Previous call chain:
0) call dma_get_required_mask() (kernel/dma.c)
1) call ppc_md.dma_get_required_mask, if it exists. On powernv, that
points to pnv_dma_get_required_mask() (platforms/powernv/setup.c)
2) device is PCI, therefore call pnv_pci_dma_get_required_mask()
(platforms/powernv/pci.c)
3) call phb->dma_get_required_mask if it exists
4) it only exists in the ioda case, where it points to
pnv_pci_ioda_dma_get_required_mask() (platforms/powernv/pci-ioda.c)
New call chain:
0) call dma_get_required_mask() (kernel/dma.c)
1) device is PCI, therefore call pci_controller_ops.dma_get_required_mask
if it exists
2) in the ioda case, that points to pnv_pci_ioda_dma_get_required_mask()
(platforms/powernv/pci-ioda.c)
In the p5ioc2 case, the call chain remains the same -
dma_get_required_mask() does not find either a ppc_md call or
pci_controller_ops call, so it calls __dma_get_required_mask().
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The relation between CONFIG_PPC_HAS_HASH_64K and CONFIG_PPC_64K_PAGES is
painfully complicated.
But if we rearrange it enough we can see that PPC_HAS_HASH_64K
essentially depends on PPC_STD_MMU_64 && PPC_64K_PAGES.
We can then notice that PPC_HAS_HASH_64K is used in files that are only
built for PPC_STD_MMU_64, meaning it's equivalent to PPC_64K_PAGES.
So replace all uses and drop it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
For config options with only a single value, guarding the single value
with 'if' is the same as adding a 'depends' statement. And it's more
standard to just use 'depends'.
And if the option has both an 'if' guard and a 'depends' we can collapse
them into a single 'depends' by combining them with &&.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Now that support for 64k pages with a 4K kernel is removed, this code is
unreachable.
CONFIG_PPC_HAS_HASH_64K can only be true when CONFIG_PPC_64K_PAGES is
also true.
But when CONFIG_PPC_64K_PAGES is true we include pte-hash64.h which
includes pte-hash64-64k.h, which defines both pte_pagesize_index() and
crucially __real_pte, which means this definition can never be used.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Back in the olden days we added support for using 64K pages to map the
SPU (Synergistic Processing Unit) local store on Cell, when the main
kernel was using 4K pages.
This was useful at the time because distros were using 4K pages, but
using 64K pages on the SPUs could reduce TLB pressure there.
However these days the number of Cell users is approaching zero, and
supporting this option adds unpleasant complexity to the memory
management code.
So drop the option, CONFIG_SPU_FS_64K_LS, and all related code.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
The powerpc kernel can be built to have either a 4K PAGE_SIZE or a 64K
PAGE_SIZE.
However when built with a 4K PAGE_SIZE there is an additional config
option which can be enabled, PPC_HAS_HASH_64K, which means the kernel
also knows how to hash a 64K page even though the base PAGE_SIZE is 4K.
This is used in one obscure configuration, to support 64K pages for SPU
local store on the Cell processor when the rest of the kernel is using
4K pages.
In this configuration, pte_pagesize_index() is defined to just pass
through its arguments to get_slice_psize(). However pte_pagesize_index()
is called for both user and kernel addresses, whereas get_slice_psize()
only knows how to handle user addresses.
This has been broken forever, however until recently it happened to
work. That was because in get_slice_psize() the large kernel address
would cause the right shift of the slice mask to return zero.
However in commit 7aa0727f33 ("powerpc/mm: Increase the slice range to
64TB"), the get_slice_psize() code was changed so that instead of a
right shift we do an array lookup based on the address. When passed a
kernel address this means we index way off the end of the slice array
and return random junk.
That is only fatal if we happen to hit something non-zero, but when we
do return a non-zero value we confuse the MMU code and eventually cause
a check stop.
This fix is ugly, but simple. When we're called for a kernel address we
return 4K, which is always correct in this configuration, otherwise we
use the slice mask.
Fixes: 7aa0727f33 ("powerpc/mm: Increase the slice range to 64TB")
Reported-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
We forgot to install the tempfile, so when the selftests are installed
and then run the subpage_prot_file test fails.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch plugs the leak of irq_bitmap, allocated as part of
initialization of cxl_context struct; during the call to
afu_allocate_irqs. The bitmap is now release during the call to function
afu_release_irqs.
Reported-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
CONFIG_CXL_EEH is for CXL's EEH related code.
Other drivers can depend on or #ifdef on this symbol to configure
PERST behaviour, allowing CXL to participate in the EEH process.
Reviewed-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
EEH (Enhanced Error Handling) allows a driver to recover from the
temporary failure of an attached PCI card. Enable basic CXL support
for EEH.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Provide a kernel API and a sysfs entry which allow a user to specify
that when a card is PERSTed, it's image will stay the same, allowing
it to participate in EEH.
cxl_reset is used to reflash the card. In that case, we cannot safely
assert that the image will not change. Therefore, disallow cxl_reset
if the flag is set.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If the driver doesn't participate in EEH, the AFUs will be removed
by cxl_remove, which will be invoked by EEH.
If the driver does particpate in EEH, the vPHB needs to stick around
so that the it can particpate.
In both cases, we shouldn't remove the AFU/vPHB.
Reviewed-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
As with an adapter, some aspects of initialisation are done only once
in the lifetime of an AFU: for example, allocating memory, or setting
up sysfs/debugfs files.
However, we may want to be able to do some parts of the initialisation
multiple times: for example, in error recovery we want to be able to
tear down and then re-map IO memory and IRQs.
Therefore, refactor AFU init/teardown as follows.
- Create two new functions: 'cxl_configure_afu', and its pair
'cxl_deconfigure_afu'. As with the adapter functions,
these (de)configure resources that do not need to last the entire
lifetime of the AFU.
- Allocating and releasing memory remain the task of 'cxl_alloc_afu'
and 'cxl_release_afu'.
- Once-only functions that do not involve allocating/releasing memory
stay in the overarching 'cxl_init_afu'/'cxl_remove_afu' pair.
However, the task of picking an AFU mode and activating it has been
broken out.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Some aspects of initialisation are done only once in the lifetime of
an adapter: for example, allocating memory for the adapter,
allocating the adapter number, or setting up sysfs/debugfs files.
However, we may want to be able to do some parts of the
initialisation multiple times: for example, in error recovery we
want to be able to tear down and then re-map IO memory and IRQs.
Therefore, refactor CXL init/teardown as follows.
- Keep the overarching functions 'cxl_init_adapter' and its pair,
'cxl_remove_adapter'.
- Move all 'once only' allocation/freeing steps to the existing
'cxl_alloc_adapter' function, and its pair 'cxl_release_adapter'
(This involves moving allocation of the adapter number out of
cxl_init_adapter.)
- Create two new functions: 'cxl_configure_adapter', and its pair
'cxl_deconfigure_adapter'. These two functions 'wire up' the
hardware --- they (de)configure resources that do not need to
last the entire lifetime of the adapter
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- MMIO pointer unmapping is guarded by a null pointer check.
However, iounmap doesn't null the pointer, just invalidate it.
Therefore, explicitly null the pointer after unmapping.
- afu_desc_mmio also needs to be unmapped.
- PCI regions are allocated in cxl_map_adapter_regs.
Therefore they should be released in unmap, not elsewhere.
Acked-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Check if an IRQ is mapped before releasing it.
This will simplify future EEH code by allowing unconditional unmapping
of IRQs.
Acked-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Previously the SPA was allocated and freed upon entering and leaving
AFU-directed mode. This causes some issues for error recovery - contexts
hold a pointer inside the SPA, and they may persist after the AFU has
been detached.
We would ideally like to allocate the SPA when the AFU is allocated, and
release it until the AFU is released. However, we don't know how big the
SPA needs to be until we read the AFU descriptor.
Therefore, restructure the code:
- Allocate the SPA only once, on the first attach.
- Release the SPA only when the entire AFU is being released (not
detached). Guard the release with a NULL check, so we don't free
if it was never allocated (e.g. dedicated mode)
Acked-by: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If the PCI channel has gone down, don't attempt to poke the hardware.
We need to guard every time cxl_whatever_(read|write) is called. This
is because a call to those functions will dereference an offset into an
mmio register, and the mmio mappings get invalidated in the EEH
teardown.
Check in the read/write functions in the header.
We give them the same semantics as usual PCI operations:
- a write to a channel that is down is ignored.
- a read from a channel that is down returns all fs.
Also, we try to access the MMIO space of a vPHB device as part of the
PCI disable path. Because that's a read that bypasses most of our usual
checks, we handle it explicitly.
As far as user visible warnings go:
- Check link state in file ops, return -EIO if down.
- Be reasonably quiet if there's an error in a teardown path,
or when we already know the hardware is going down.
- Throw a big WARN if someone tries to start a CXL operation
while the card is down. This gives a useful stacktrace for
debugging whatever is doing that.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We're about to make these more complex, so make them functions
first.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In the complete hotplug case, EEH PEs are supposed to be released
and set to NULL. Normally, this is done by eeh_remove_device(),
which is called from pcibios_release_device().
However, if something is holding a kref to the device, it will not
be released, and the PE will remain. eeh_add_device_late() has
a check for this which will explictly destroy the PE in this case.
This check in eeh_add_device_late() occurs after a call to
eeh_ops->probe(). On PowerNV, probe is a pointer to pnv_eeh_probe(),
which will exit without probing if there is an existing PE.
This means that on PowerNV, devices with outstanding krefs will not
be rediscovered by EEH correctly after a complete hotplug. This is
affecting CXL (CAPI) devices in the field.
Put the probe after the kref check so that the PE is destroyed
and affected devices are correctly rediscovered by EEH.
Fixes: d91dafc02f ("powerpc/eeh: Delay probing EEH device during hotplug")
Cc: stable@vger.kernel.org
Cc: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Section 3.7 of Version 1.2 of the Power8 Processor User's Manual
prescribes that updates to HID0 be preceded by a SYNC instruction and
followed by an ISYNC instruction (Page 91).
Create an inline function name update_power8_hid0() which follows this
recipe and invoke it from the static split core path.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Tested-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Replace hard coded values with existing DRCONF flags while procesing
detected LMBs from the device tree. Does not change any functionality.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The value of 'valid' is always zero when 'esid' is zero, and if 'esid'
is non-zero then the value of 'valid' is irrelevant because we are using
logical or in the if expression.
In fact 'valid' can be dropped completely from dump_segments() by
simply doing the check with SLB_ESID_V directly in the if.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
[mpe: Rewrite change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The code to fetch the SLB size from the device tree wants to first look
for "slb-size" and then if that's not found "ibm,slb-size".
We can simplify the code by looking for the properties and then if we
find one of them we set mmu_slb_size.
We also change the function name from check_cpu_slb_size() to
init_mmu_slb_size() as the function doesn't check anything, it only
initialises mmu_slb_size.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
[mpe: Rewrite change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds some documentation to patch_slb_encoding() explaining
how it works.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
[mpe: Update change log and mention the signedness of the immediate]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The SLB code uses 'slot' and 'entry' interchangeably, change it to always
use 'entry'.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
[mpe: Rewrite change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch just removes one redundant entry for one extern variable
'slb_compare_rr_to_size' from the scope. This patch does not change
any functionality.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
An IO address, tagged with __iomem, is passed to debugfs_create_file
as private data. This requires that it be cast to void *. The cast
drops the __iomem annotation and so creates a sparse warning:
drivers/misc/cxl/debugfs.c:51:57: warning: cast removes address space of expression
The address space marker is added back in the file operations
(fops_io_u64).
Silence the warning with __force.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
A few declarations were identified by sparse as needing to be static:
drivers/misc/cxl/irq.c:408:6: warning: symbol 'afu_irq_name_free' was not declared. Should it be static?
drivers/misc/cxl/irq.c:467:6: warning: symbol 'afu_register_hwirqs' was not declared. Should it be static?
drivers/misc/cxl/file.c:254:6: warning: symbol 'afu_compat_ioctl' was not declared. Should it be static?
drivers/misc/cxl/file.c:399:30: warning: symbol 'afu_master_fops' was not declared. Should it be static?
Make them static.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It's a good idea, and it brings us in line with the rest of arch/powerpc.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add a new powerpc-specific trace clock using the timebase register,
similar to x86-tsc. This gives us
- a fast, monotonic, hardware clock source for trace entries, and
- a clock that can be used to correlate events across cpus as well as across
hypervisor and guests.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In case of error, the functions platform_get_resource() and kmalloc()
returns NULL not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
wf_find_control(), wf_find_sensor(), and wf_is_overtemp() are exported
but unused. Remove these three functions.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
wf_critical_overtemp() is exported. But nothing uses that export.
That's unsurprising because there's no header that defines it. Stop
exporting that function and make it static.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
wf_unregister_client() increments the client count when a client
unregisters. That is obviously incorrect. Decrement that client count
instead.
Fixes: 75722d3992 ("[PATCH] ppc64: Thermal control for SMU based machines")
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use %pR to simplify the debug code. This also make the debug info more
readable.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
[mpe: Unsplit multi-line printk strings]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently when attaching a context in dedicated mode, we ignore the
result of add_process_element(), which could potentially fail.
If add_process_element() returns an error, pass it back to the caller.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Invoke new opal_cec_reboot2() call with reboot type
OPAL_REBOOT_PLATFORM_ERROR (for unrecoverable HMI interrupts) to inform
BMC/OCC about this error, so that BMC can collect relevant data for error
analysis and decide what component to de-configure before rebooting.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On non-recoverable MCE errors in kernel space, Linux kernel panics
and system reboots. On BMC based system opal-prd runs as a daemon
in the host. Hence, kernel crash may prevent opal-prd to detect and
analyze this MCE error. This may land us in a situation where the faulty
memory never gets de-configured and Linux would keep hitting same MCE error
again and again. If this happens in early stage of kernel initialization,
then Linux will keep crashing and rebooting in a loop.
This patch fixes this issue by invoking new opal_cec_reboot2() call with
reboot type OPAL_REBOOT_PLATFORM_ERROR to inform BMC/OCC about this
error, so that BMC can collect relevant data for error analysis and
decide what component to de-configure before rebooting.
This patch is dependent on OPAL patchset posted on skiboot mailing list
at https://lists.ozlabs.org/pipermail/skiboot/2015-July/001771.html that
introduces opal_cec_reboot2() opal call.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In the event of unrecovered HMI the existing code panics as soon as
it receives the first unrecovered HMI event. This makes host to report
partial information about HMIs before panic. There may be more errors
which would have caused the HMI and hence more HMI event would have been
generated waiting to be pulled by host. This patch implements a logic to
pull and display all the HMI event before going down panic path.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The V2 version of HMI event now carries additional information for
Malfunction Alert. It now contains error information about CORE and NX
checkstop. This patch checks and displays the check stop reason before
panic.
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Acked-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
