New codec ALC255/ALC3234 support multifunction jacks.
It used for menual select the input device.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit [8fe7b65ab4: ALSA: hda - Apply GPIO setup for MacBooks
with CS4208] added a fixup entry matching with the vendor id 0x106b.
This broke the fixups for previous MBA6,1 and 6,2, since the PCI SSID
vendor id matches before evaluating the codec SSIDs.
We had a similar issue on Mac with Sigmatel codecs, and solve this
problem again similarly, by introducing a skeleton entry matching with
the all MacBooks, then remap to the right one.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=64401
Fixes: 8fe7b65ab4 ('ALSA: hda - Apply GPIO setup for MacBooks with CS4208')
Cc: <stable@vger.kernel.org> [v3.12+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Upon suspend / resume, the fixup register settings are lost because
sending HDA_FIXUP_ACT_PRE_PROBE is not part of the resume path. Instead,
write our registers in response to the HDA_FIXUP_ACT_INIT, which happens
after initial probe and upon resume.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
dmesg here has a 100+ consecutive lines of:
[ 1464.219446] hda-intel 0000:00:14.2: spurious response 0x0:0x0, last cmd=0x170500
[ 1464.219451] hda-intel 0000:00:14.2: spurious response 0x0:0x0, last cmd=0x170500
[ 1464.219454] hda-intel 0000:00:14.2: spurious response 0x0:0x0, last cmd=0x170500
...
Ratelimit the message to reduce the dmesg log noise.
Coalesce the format while at it.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the recent fake ELD patches, we can remove the check for AMD
HDMI in hdmi_present_sense() and decide the return value from
eld_valid value.
Suggested by Anssi Hannula.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just added a missing ifdef:
sound/pci/ice1712/quartet.c:210:14: warning: 'get_binary' defined but not used [-Wunused-function]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This fixes a race condition in case several monitors are being
repolled in parallel.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the jack should not be reported to userspace (e g, because it is
in some transitional state), one can set this flag.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is a small gap between the jack detection unsolicited event and
the time the ELD is updated. When user-space queries the HDMI ELD
immediately after receiving the notification, it might fail because of
this gap.
For avoiding such a problem, this patch tries to delay the HDMI jack
detect notification until ELD information is fully updated. The
workaround is imperfect, but good enough as a starting point.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This machine has a multi-function headset jack.
BugLink: https://bugs.launchpad.net/bugs/1248856
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BIOS on ASUS W5A laptop with ALC880 codec doesn't provide any pin
configurations, so we have to set up all pins manually.
Reported-and-tested-by: nb <nb@dagami.org>
Cc: <stable@vger.kernel.org> [v3.4+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It's a superset of the existing CX2075x codecs, so we can reuse the
existing parser code.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The warnings are really harmless but annoying. Since they are only
about debug prints, and it's at most 32bit DMA, let's just cast to
unsigned long.
sound/pci/lx6464es/lx6464es.c:457:22: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
sound/pci/lx6464es/lx_core.c:1195:21: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This machine has a mute LED as well as a noisy internal mic. Hence it needs
quirks for both limiting the mic boost as well as enabling the LED.
BugLink: https://bugs.launchpad.net/bugs/1248476
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some HP machines with Realtek codecs have mute LEDs connected to VREF pins.
However when these go into runtime suspend, the pin powers down and its
pin control is disabled, thus disabling the LED too.
This patch fixes that issue by making sure that the pin stays in D0 with
correct pin control.
Cc: stable@kernel.org
BugLink: https://bugs.launchpad.net/bugs/1248465
Tested-by: Franz Hsieh <franz.hsieh@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BUG_ON() is rather useless for debugging as it leads to panic().
Use WARN_ON() and handle the error cases accordingly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The playback chmap for multi-channel stream hasn't been properly added
to intel8x0 devices due to the wrong condition.
Reported-by: Raymond Yau <superquad.vortex2@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
"HDA Intel MID" is no correct name for Haswell HDMI controllers.
Give them a better name, "HDA Intel HDMI".
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Haswell HDMI audio controllers seem to get stuck when unaligned buffer
size is used. Let's enable the buffer alignment for the corresponding
entries.
Since AZX_DCAPS_INTEL_PCH contains AZX_DCAPS_BUFSIZE that disables the
buffer alignment forcibly, define AZX_DCAPS_INTEL_HASWELL and put the
necessary AZX_DCAPS bits there.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60769
Reported-by: Alexander E. Patrakov <patrakov@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Same as we already have for Conexant. Right now it's only enabled
for one machine.
Tested-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The device IDs of the AMD Cypress/Juniper/Redwood/Cedar/Cayman/Antilles/
Barts/Turks/Caicos HDMI HDA controllers weren't added explicitly
because the generic entry works, but it made the device appearing as
"Generic", and people are confused as if it's no proper HDMI
controller. Add them so that the name shows up properly as "ATI HDMI"
instead of "Generic".
According to Takashi's tests and the lack of complaints, these devices
work fine without disabling snooping.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a bitmask to hda_gen_spec indicating NIDs to exclude from the
possible volume controls. That is, when the bit is set, the NID
corresponding to the bit won't be picked as an output volume control
any longer.
Basically this is just a band-aid for working around the issue found
with CS4208 codec, where only the headphone pin has a volume AMP with
different dB steps.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60811
Cc: <stable@vger.kernel.org> [v3.12+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Check the TLV db scale result before actually dividing in vmaster
slave init code. Also mask TLV_DB_SCALE_MUTE bit so that the right
value is obtained even if this bit is set by the codec driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BIOS on Acer TravelMate 6293 doesn't set up the SPDIF output pin
correctly as default, so enable it via a fixup entry.
Reported-and-tested-by: Hagen Heiduck <heiduck.suse@fmail.postpro.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the HD Audio Device IDs for the Intel Wildcat Point-LP PCH.
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The function name not_share_unassigned_cvt() is opposite to what it does.
This patch renames it to intel_not_share_assigned_cvt(), and addes comments
to explain why some Intel display codecs need this workaround.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
NVIDIA HDMI codecs do not seem to follow the Audio Sample Packet (ASP)
channel mapping (as set by verb F32h per HDA specification 7.3.3.41)
when playing back 2-channel audio (CEA CA 0x00).
Basically this means that specifying swapped channels for stereo audio
(FR,FL) does not take effect, and e.g. this command plays back on the
wrong channel:
speaker-test -c2 -Dhdmi:CARD=NVidia,DEV=0 -m FR,FL -s1
Multichannel audio is not affected.
This issue has been confirmed to exist on codec 0x10de0015 by me and on
0x10de0040 by Juho Teperi.
Disable 2ch FL/FR channel swapping on all NVIDIA HDMI codecs that use
the standard HDA channel mapping system. Since this is a very minor
functionality loss, we err on the side of disabling it for newer codecs
as well until any future testing confirms that this issue has been
fixed.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Helped-by: Juho Teperi <juho.teperi@iki.fi>
Cc: Aaron Plattner <aplattner@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For Valleyview display codec, if an unused pin chooses an assgined converter
selected by a used pin, playback on the unused pin can also give sound to the
output device of the used pin. It's because data flows from the same convertor
to the display port of the used pin. This issue is same as Haswell.
So this patch avoids using assinged convertors for unused pins.
The related function haswell_config_cvts() is renamed for code reuse.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASUS N56VZ and N76VZ laptops have a bass speaker but its output comes
only from the right channel. This patch adds the extra chmap specific
to these models.
Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=846531
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASUS N76VZ needs the same fixup as N56VZ for supporting the boost
speaker.
Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=846529
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALC283-based Chromebook suffers from occasional white noise, and it
turned out that this comes from AA-loopback. Disable this output path
by just clearing mixer_nid, then the generic parser will skip the
creation of AA-loopback path.
Reported-and-tested-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The FUNCTION_TYPE parameter isn't associated with any NID, thus
showing the uninitialized nid in the error message is simply
nonsense.
Spotted by coverity CID 145068.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Just pass the error code returned from copy_from_user_toio() and
copy_to_user_fromio() helpers.
Spotted by coverity CID 114119.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The variable runtime is never used, and this might be even a source of
NULL-dereference. Nothing better than killing it.
Spotted by coverity CID 100862.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix a possible NULL access of indexp in fill_audio_out_name() called
from snd_hda_get_pin_label().
Spotted by coverity CID 402035.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As EAPD on NID 0x12 (speaker pin) is used as the master amp on
Thinkpads with AD1984A codec, we can hook this to vmaster for saving a
bit more power at master mute state.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AD1984A codec has a couple of pins with EAPD controls, and the generic
codec driver tries to turn each of them on/off depending on the pin
active state. However, Thinkpads seem to use EAPD of the speaker pin
as a master EAPD for controlling the mute of all outputs, including
the headphone. This results in the dead headphone output via the
headphone plugging because it mutes the speaker and turns off EAPD.
The fix is to simply add spec->gen.keep_on_eapd flag.
[This is a regression fix on 3.12 where we moved the AD codec parser
to the generic parser. 3.11 and earlier didn't show this problem
because still static quirks have been used.]
Reported-and-tested-by: Vito Caputo <vcaputo@gnugeneration.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The generic parser has a support of vmaster hook, but this is
initialized only in the init callback with the check of the presence
of the corresponding kctl. However, since kctl is NULL at the very
first init callback that is called before build_controls callback, the
vmaster hook sync is skipped there. Eventually this leads to the
uninitialized state depending on the hook implementation.
This patch adds a simple workaround, just calling the sync function
explicitly at build_controls callback.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Further work on the dmaengine helpers, including support for
configuring the parameters for DMA by reading the capabilities of the
DMA controller which removes some guesswork and magic numbers fromm
drivers.
- A refresh of the documentation.
- Conversions of many drivers to direct regmap API usage in order to
allow the ASoC level register I/O code to be removed, this will
hopefully be completed by v3.14.
- Support for using async register I/O in DAPM, reducing the time taken
to implement power transitions on systems that support it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=rVsK
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v3.13
- Further work on the dmaengine helpers, including support for
configuring the parameters for DMA by reading the capabilities of the
DMA controller which removes some guesswork and magic numbers fromm
drivers.
- A refresh of the documentation.
- Conversions of many drivers to direct regmap API usage in order to
allow the ASoC level register I/O code to be removed, this will
hopefully be completed by v3.14.
- Support for using async register I/O in DAPM, reducing the time taken
to implement power transitions on systems that support it.
hdmi_setup_audio_infoframe() does not set up pin and infoframe if there
is no connected sink. If a sink is connected while audio playback is
already in progress, the pin and infoframe will not be properly set up,
causing no audio or wrongly mapped audio.
On Intel Haswell codecs the hdmi_setup_audio_infoframe() is already
called again from hdmi_present_sense() when an ELD appears because
transcoder:port mapping may have changed.
Make the call non-Haswell-specific so that audio will be properly set up
if the playback was started before a sink was connected.
Tested on non-Haswell Intel HDMI codec by plugging sink in during
playback.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Recent AMD HDMI codecs (revision ID 3 and later, 0x100300 as reported by
procfs codec#0) have a configurable ramp-up/down functionality.
The documentation ( http://www.x.org/docs/AMD/AMD_HDA_verbs_v2.pdf )
specifies that 180 ("180/256 =~ 0.7") is recommended for PCM and 0 for
non-PCM.
Apply the recommended values according to provided S/PDIF AES0 settings
since ramp-up/down does not make sense for non-PCM.
v2: adapted to hdmi_ops infrastructure
* More note from Anssi:
actually, re-reading mails reveals that Olivier didn't find the
expected difference with this setting, except for "maybe slightly
slower startup with AES0=6" (i.e. value 0, which is unexpected).
So maybe
a) it makes too unnoticiable a difference, or
b) only affects certain hardware (card and/or sink), or
c) ramp-up/down is only triggered with the MUTE bit of
ATI_VERB_SET_MULTICHANNEL_xx which is also rev3+ specific,
but is not presently used by the driver,
or something else.
So there's a significant chance setting ramp rate is useless for us ATM,
but probably does not do actual harm either.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Tested-by: Olivier Langlois <olivier@trillion01.com> # v1
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ATI/AMD HDMI codecs do not include standard HDA HDMI HBR support (which
is required for bitstreaming DTS-HD and Dolby TrueHD), instead they have
custom verbs for checking and enabling it.
Add support for the ATI/AMD HDMI HBR verbs.
The specification is available at:
http://www.x.org/docs/AMD/AMD_HDA_verbs_v2.pdf
v2: adapted to hdmi_ops infrastructure
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Tested-by: Peter Frühberger <fritsch@xbmc.org> # v1
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ATI/AMD HDMI/DP codecs do not include standard HDA ELD (EDID-like data)
support.
In place of providing access to an ELD buffer, various vendor-specific
verbs are provided to provide the relevant information. Revision ID 3
and later (0x100300 as reported by procfs codec#X) have support for
providing more information than the previous revisions (but only if
supported by the display driver).
Generate ELD from the information provided by the vendor-specific verbs
on ATI/AMD codecs.
The specification is available at:
http://www.x.org/docs/AMD/AMD_HDA_verbs_v2.pdf
v2: moved code to hda_eld.c and cleaned it up
v3: adapted to hdmi_ops infrastructure
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Tested-by: Peter Frühberger <fritsch@xbmc.org> # v2
Tested-by: Olivier Langlois <olivier@trillion01.com> # v2
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ATI/AMD codecs do not support all the standard HDA HDMI/DP functions,
instead various vendor-specific verbs are provided.
This commit addresses these missing functions:
- standard channel mapping support
- standard infoframe configuration support
ATI/AMD provides their own verbs that allow the following:
- setting CA for infoframe
- setting down-mix information for infoframe
- channel pair remapping
- individual channel remapping (revision ID 3+, 0x100300+)
The documentation for the verbs has now been released by AMD:
http://www.x.org/docs/AMD/AMD_HDA_verbs_v2.pdf
Add support for the ATI/AMD specific verbs and use them instead of the
generic methods on ATI/AMD codecs. This allows multi-channel PCM audio
to work.
Channel remapping is restricted to pairwise mapping on codecs with
revision ID 2 (0x100200 as reported by procfs codec#X) or lower. This
means cards up to Radeon HD7670 as far as I know. This will not affect
standard multi-channel modes since these codecs support automatic
FC-LFE swapping for HDMI.
ATI/AMD codecs do not advertise all of their supported rates, formats
and channel counts, therefore that information is forced accordingly so
that all HDMI 1.x PCM parameters are marked as supported.
Support for multiple ports is also added to patch_atihdmi so that
0x1002aa01 codecs with multiple ports will work properly when switched
back to that patch.
v2: splitted ELD emulation to a separate patch, tlv fixes
v3: adapted to the new hdmi_ops infrastructure, fixed rev3+ vendor id
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Tested-by: Peter Frühberger <fritsch@xbmc.org> # v2
Tested-by: Olivier Langlois <olivier@trillion01.com> # v2+rev3fix
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Upcoming AMD multichannel support requires many customized operations
(channel mapping, ELD, HBR) but can otherwise share most of its code
with the generic patch.
Add a local struct hdmi_ops containing customizable HDMI-specific
callbacks and move the current code to those callbacks. Functionality is
unaltered.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some machine with 85ms delay might be happen pop noise when codec
enter to D3. Raise up to 100ms delay will be match for more machine.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When HP laptops with mute and mic-record LEDs go to runtime suspend,
these LEDs are turned on forcibly no matter whether GPIO pis are on or
off. This strange behavior seems triggered by resetting the HD-audio
bus link at azx_rutime_suspend(). So, just add a new hda_bus flag to
avoid the link reset at runtime suspend and set it for these HP
machines.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It's just another variant of ALC269 & co.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Emitting an OOM message isn't necessary after input_allocate_device
as there's a generic OOM and a dump_stack already done.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a machine goes to S3/S4 after power-save is enabled, the runtime
PM refcount might be incorrectly decreased because the power-down
triggered soon after resume assumes that the controller was already
powered up, and issues the pm_notify down.
This patch fixes the incorrect pm_notify call simply by checking the
current value properly.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
... which was introduced by the previous commit a4e9a38b, causing
build errors without CONFIG_PROC_FS.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds codec ID (0x80862882) and module alias for
Valleyview2 display codec.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Partially restructures _snd_emu10k1_audigy_init_efx() and
_snd_emu10k1_init_efx() functions.
Be noted that the cast is demanded to use '__user'. So, in these cases,
avoid patches based on the coccinelle 'drop_kmalloc_cast' semantic patch.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the lock is used primarily in patch_hdmi.c, it's better to move
it in the local struct instead of exporting in hda_eld. The only
functions requiring the lock in hda_eld.c are proc accessors. So in
this patch, the proc entry and its creation/deletion/accessors are
moved into patch_hdmi.c, together with the mutex lock to pin_spec
struct.
The former proc info functions are exported so that they can be called
from patch_hdmi.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some per_pin fields and ELD contents might be changed dynamically in
multiple ways where the concurrent accesses are still opened in the
current code. This patch fixes such possible races by using eld->lock
in appropriate places.
Reported-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The zero-length connection list happens so often on Haswell HDMI, and
it results in warning messages like
ALSA: hda_codec: invalid CONNECT_LIST verb 5[1]:0
at each time the codec resumes from the power-save, which is fairly
annoying.
Since this is no real error, make it shown only in the verbose debug
mode.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A fixup which should be called before codec being freed will come
to use in the next patch.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In GCC the sizeof(hdsp_version) is 8 because there is a 2 byte hole at
the end of the struct after ->firmware_rev.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The create_bind_cap_vol_ctl does not create any control indicating
that an inverted dmic is present. Therefore, create multiple
capture volumes in this scenario, so we always have some indication
that the internal mic is inverted.
This happens on the Lenovo Ideapad U310 as well as the Lenovo Yoga 13
(both are based on the CX20590 codec), but the fix is generic and
could be needed for other codecs/machines too.
Thanks to Szymon Acedański for the pointer and a draft patch.
BugLink: https://bugs.launchpad.net/bugs/1239392
BugLink: https://bugs.launchpad.net/bugs/1227491
Reported-by: Szymon Acedański <accek@mimuw.edu.pl>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Using the headset mic model will cause the headset mic to be labeled
"headset mic" instead of just "mic".
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The external mic showed up with a precense detect of "always present",
essentially disabling the internal mic. Therefore turn off presence
detection for this pin.
Note: The external mic seems not yet working, but an internal mic is
certainly better than no mic at all.
Cc: stable@vger.kernel.org
BugLink: https://bugs.launchpad.net/bugs/1227093
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the case where we have both line out and more than stereo speakers,
the speaker DACs will end up in extra_out_nid.
In fact, AFAIU, speakers are the only ones that can end up in extra_out_nid,
and if we have several of those, they should be surround outputs
rather than copy front.
BugLink: https://bugs.launchpad.net/bugs/1236965
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASUS N56VZ needs a fixup for the bass speaker pin, which was already
provided via model=asus-mode4.
Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=841645
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently hdmi_setup_audio_infoframe() reprograms the HDA channel
mapping only when the infoframe is not up-to-date or the non-PCM flag
has changed.
However, when just the channel map has been changed, the infoframe may
still be up-to-date and non-PCM flag may not have changed, so the new
channel map is not actually programmed into the HDA codec.
Notably, this failing case is also always triggered when the device is
already in a prepared state and a new channel map is configured while
changing only the channel positions (for example, plain
"speaker-test -c2 -m FR,FL").
Fix that by always programming the channel map in
hdmi_setup_audio_infoframe(). Tested on Intel HDMI.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allow channel map debugging for both automatic and manual channel maps,
and print CA always when updating infoframe.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently the available channel maps TLV only contains channel maps that
are limited to the traditional 7.1 speakers.
Since the other HDMI channel mapping functions have been fixed to
properly handle all CEA-861-E specified speakers, allow them to be
listed.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For some speakers and slots the CEA slot <-> speaker assignment depends
on the used CEA Channel Allocation value.
Therefore the from_cea_slot() and to_cea_slot() helpers currently only
work correctly for the regular 7.1 speakers.
Fix them to work with all speakers, taking the re-ordered CA index as
input and adapting use sites accordingly.
This change allows manual channel mapping to actually work for all CEA
allocated speakers. Additionally, this fixes incorrect channel map
reporting in automatic channel mapping mode when an affected speaker
position is used (e.g. 6.1 map which contains an RC speaker).
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
hdmi_manual_setup_channel_mapping() and hdmi_std_setup_channel_mapping
try to assign ALSA channels to HDMI channel slots and disable (i.e.
silence) other slots.
However, they try to disable a slot by using AC_VERB_SET_CHAN_SLOT with
parameter ((alsa_ch << 8) | 0xf), while the correct parameter is
((0xf << 8) | hdmi_slot), i.e. the slot should be unassigned, not the
ALSA channel.
Fix that by actually disabling the unused slots.
Note that this bug did not cause any (reported) issues because slots
incorrectly having audio are normally ignored by a receiver if the CEA
channel allocation used does not map that slot to any speaker.
Additionally, the converter channel count configuration limits the
number of actually active channels in any case.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently the converter channel count is set to the number of actual
input channels. The audio infoframe channel count field is set
similarly.
However, sometimes the used channel map does not map all input channels
to outputs. Notably, 3 channel modes (e.g. 2.1) require a dummy input
channel so there are 4 input channels. According to the HDA
specification, converter channel count should be programmed according to
the number of _active_ channels.
On Intel HDMI codecs (but not on NVIDIA), setting the converter channel
to a higher value than there are actually mapped channels to HDMI slots
will cause no audio to be output at all.
Note that the effects of this issue are currently partially masked by
other bugs that prevent the driver from actually unmapping channels in
certain cases. For example, if a 4 channel stream is first created and
prepared, it gets a FL,FR,RL,RR mapping (ALSA->HDMI slot mapping 0->0,
1->1, 2->4, 3->5). If one thereafter assigns a FR,FL,FC mapping to it,
the driver will remap 2->3 but fail to unmap 2->4 and 3->5, so there are
still 4 active channels and the issue will not trigger in this case.
These bugs will be fixed separately.
Fix the channel counts in the converter channel count field and in the
audio infoframe channel count field to match the actual number of active
channels.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
hdmi_std_setup_channel_mapping() selects a Channel Allocation according
to the sink reported speaker mask, preferring the ALSA standard layouts.
If the channel allocation is not one of the ALSA standard layouts, the
ALSA channels are mapped directly to HDMI channels in order. However,
the function does not take into account that there a holes in the HDMI
channel map.
Additionally, the function tries to disable a slot by using
AC_VERB_SET_CHAN_SLOT with parameter ((alsa_ch << 8) | 0xf), while the
correct parameter is ((0xf << 8) | hdmi_slot), i.e. the slot should be
unassigned, not the ALSA channel.
Fix both of the issues for non-ALSA-default layouts.
Tested on Intel HDMI with a speaker mask of FL | FR | FC | RC, which
causes CA 0x06 to be selected for 4-channel audio, which causes
incorrect output (sound destined to RC goes to FC and FC goes nowhere)
without the patch.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
hdmi_setup_fake_chmap() is supposed to set the reported channel map when
the channel map is not specified by the user.
However, the function indexes channel_allocations[] with a wrong value
and extracts the wrong nibble from hdmi_channel_mapping[], causing wrong
channel maps to be shown.
Fix those issues.
Tested on Intel HDMI to correctly generate various channel maps, for
example 3,4,14,15,7,8,5,6 (instead of incorrect 3,4,8,7,5,6,14,0) for
standard 7.1 channel audio. (Note that the side and rear channels are
reported as RL/RR and RLC/RRC, respectively, as per the CEA-861
standard, instead of the more traditional SL/SR and RL/RR.)
Note that this only fixes the layouts that only contain traditional 7.1
speakers (2.0, 2.1, 4.0, 5.1, 7.1, etc.). E.g. the rear center of 6.1
is still being shown wrongly due to an issue with from_cea_slot()
which will be fixed in a later patch.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On this machine, DAC on node 0x03 seems to give mono output.
Also, it needs additional patches for headset mic support.
It supports CTIA style headsets only.
Alsa-info available at the bug link below.
Cc: stable@kernel.org (v3.10+)
BugLink: https://bugs.launchpad.net/bugs/1236228
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acer Aspire 3830TG seems requiring GPIO bit 0 as the primary mute
control. When a machine is booted after Windows 8, the GPIO pin is
turned off and it results in the silent output.
This patch adds the manual fixup of GPIO bit 0 for this model.
Reported-by: Christopher <DIDI2002@web.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add 0x54584e03 ID for TI TLV320AIC27 AC'97 codec according to datasheet:
http://www.ti.com/lit/ds/slas253a/slas253a.pdf
The weird thing is that the chip is physically marked 320AD91.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
More thorough testing showed that these verbs were necessary to
improve quality of the internal mic. Patch originally from Realtek.
BugLink: https://bugs.launchpad.net/bugs/1231931
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALC283 pin control for Line1 default control by hidden register.
Use line1 as internal Mic will not get sound when boost value up.
Set control by verb for hidden register will solve this issue.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the default pin configuration and some init verbs for
setting COEFs, in addition to the correction of input pin AMP caps
for MacBook Air 6,1 and 6,2. With these changes, the headphone jack
detection starts working properly.
[trivial space fixes by tiwai]
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60811
Signed-off-by: Ben Whitten <benwhitten@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BIOS can mark a pin as "no physical connection" if the port is used by an
integrated display which is not audio capable. And audio driver will overlook
such pins.
On Haswell, such a disconneted pin will keep muted and connected to the 1st
converter by default. But if the 1st convertor is assigned to a connected pin
for audio streaming. The muted disconnected pin can make the connected pin
no sound output.
So this patch avoids using assigned converters for all unused pins for Haswell,
including the disconected pins.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Reviewed-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Convert 0 to false and 1 to true when assigning values to bool
variables. Inspired by commit 3db1cd5c05.
The simplified semantic patch that find this problem is as
follows (http://coccinelle.lip6.fr/):
@@
bool b;
@@
(
-b = 0
+b = false
|
-b = 1
+b = true
)
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
'break' after a return statement is redundant. Remove it.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
'codec_send_command' is used only in this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Local symbols used only in this file are made static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These ->put() functions are called from snd_ctl_elem_write() with user
supplied data. snd_asihpi_tuner_band_put() is missing a limit check and
the check in snd_asihpi_clksrc_put() can underflow.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few small fixes, nothing with any broad impact but all useful for the
affected systems. The Kirkwood compatible string change is fixing up a
string just added in the merge window so that we don't get any changes
in released kernels.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=oTEO
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.12-4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.12
A few small fixes, nothing with any broad impact but all useful for the
affected systems. The Kirkwood compatible string change is fixing up a
string just added in the merge window so that we don't get any changes
in released kernels.
MacBook 6,1 and 6,2 have a CS4208 codec instead of CS4206/CS4207 on
the former models. Most of functions work fine as is, except for the
silent speaker output. After debugging sessions, it turned out that
the machine needs to set GPIO 0 for the speaker amp.
This patch adds the basic support for CS4208 and the fixup for these
MacBooks. Basically the codec works just with the generic parser.
For re-using the existing GPIO amp code and init/free callbacks, a few
places have been changed so that CS4206/4207-specific codes (errata,
etc) won't hit with CS4208.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60811
Reported-and-tested-by: Imre Kaloz <kaloz@openwrt.org>
Reported-and-tested-by: Ian Munsie <darkstarsword@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Toshiba Satellite C870 shows interrupt problems occasionally when
certain mixer controls like "Mic Switch" is toggled. This seems
worked around by not using MSI.
Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=833585
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull trivial tree from Jiri Kosina:
"The usual trivial updates all over the tree -- mostly typo fixes and
documentation updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (52 commits)
doc: Documentation/cputopology.txt fix typo
treewide: Convert retrun typos to return
Fix comment typo for init_cma_reserved_pageblock
Documentation/trace: Correcting and extending tracepoint documentation
mm/hotplug: fix a typo in Documentation/memory-hotplug.txt
power: Documentation: Update s2ram link
doc: fix a typo in Documentation/00-INDEX
Documentation/printk-formats.txt: No casts needed for u64/s64
doc: Fix typo "is is" in Documentations
treewide: Fix printks with 0x%#
zram: doc fixes
Documentation/kmemcheck: update kmemcheck documentation
doc: documentation/hwspinlock.txt fix typo
PM / Hibernate: add section for resume options
doc: filesystems : Fix typo in Documentations/filesystems
scsi/megaraid fixed several typos in comments
ppc: init_32: Fix error typo "CONFIG_START_KERNEL"
treewide: Add __GFP_NOWARN to k.alloc calls with v.alloc fallbacks
page_isolation: Fix a comment typo in test_pages_isolated()
doc: fix a typo about irq affinity
...
When Gfx driver reconnects a port and transcoder, the pin amplifier will
be muted. To enable sound, the pin amp need to be unmuted.
This patch
- moves pin amp unmuting from stream preparing to hdmi_setup_audio_infoframe().
So if port:transcoder reconnection happens during stream playback, the ELDV
unsol event can stil trigger pin's amp unmuting when re-setting up audio
info frame.
- remove reading pin amp status before unmuting for speed-up, since pin amp
should always be unmuted.
- rename haswell_verify_pin_D0() to haswell_verify_D0(), since the convertor
power state is also fixed here.
This patch is mostly based on suggestion of David Henningsson.
Cc: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To apply Haswell specific fixings, this patch defines is_haswell() to check
whether a display audio codec is Haswell, to avoid explicitly checking Haswell
vendor ID everywhere.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASUS TX300 has a built-in speaker in the tablet part and in the dock
part, and the tablet speaker is supposed to be unused while the
machine is docked. The current HD-audio driver, however, doesn't
support the dock speaker, partly because BIOS doesn't set up the pin
for the corresponding output.
But, not only the missing pin config, also the missing unsol event
handling is another issue. Otherwise the automatic switching via
dock/undock won't work.
Through debugging sessions, we found out that the dock speaker pin is
NID 0x1b, and it generates an unsol event at docking/undocking, the
docking state can be inquired via the normal pin detection verb.
Also, it's turned out that GPIO 2 is needed as an amp. So, all
materials are ready to cook.
This patch provides the basic dock speaker support with TX300:
- The dock speaker is turned on/off via "Dock Speaker" mixer mute.
- The dock speaker is automatically muted when docked. This is
independently from the mixer mute switch, just like the headphone
auto-mute function.
The implementation is a bit tricky. Since we want to handle it as a
secondary speaker, we set it up a pin as a speaker with a jack
detection. Then, the fixup function registers the own unsol callback
for this pin because the standard automute can't handle the thing like
a "speaker jack". In the own automute hook, we apply the mute of the
tablet speaker in addition by checking the dock state.
Also, the speaker control names are slightly shuffled because the
generic parser doesn't give good names but blindly assumes a bass
speaker as a secondary speaker.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=59791
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull media updates from Mauro Carvalho Chehab:
"This series contains:
- Exynos s5p-mfc driver got support for VP8 encoder
- Some SoC drivers gained support for asynchronous registration
(needed for DT)
- The RC subsystem gained support for RC activity LED;
- New drivers added: a video decoder(adv7842), a video encoder
(adv7511), a new GSPCA driver (stk1135) and support for Renesas
R-Car (vsp1)
- the first SDR kernel driver: mirics msi3101. Due to some troubles
with the driver, and because the API is still under discussion, it
will be merged at staging for 3.12. Need to rework on it
- usual new boards additions, fixes, cleanups and driver
improvements"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (242 commits)
[media] cx88: Fix regression: CX88_AUDIO_WM8775 can't be 0
[media] exynos4-is: Fix entity unregistration on error path
[media] exynos-gsc: Register v4l2 device
[media] exynos4-is: Fix fimc-lite bayer formats
[media] em28xx: fix assignment of the eeprom data
[media] hdpvr: fix iteration over uninitialized lists in hdpvr_probe()
[media] usbtv: Throw corrupted frames away
[media] usbtv: Fix deinterlacing
[media] v4l2: added missing mutex.h include to v4l2-ctrls.h
[media] DocBook: upgrade media_api DocBook version to 4.2
[media] ml86v7667: fix compile warning: 'ret' set but not used
[media] s5p-g2d: Fix registration failure
[media] media: coda: Fix DT driver data pointer for i.MX27
[media] s5p-mfc: Fix input/output format reporting
[media] v4l: vsp1: Fix mutex double lock at streamon time
[media] v4l: vsp1: Add support for RT clock
[media] v4l: vsp1: Initialize media device bus_info field
[media] davinci: vpif_capture: fix error return code in vpif_probe()
[media] davinci: vpif_display: fix error return code in vpif_probe()
[media] MAINTAINERS: add entries for adv7511 and adv7842
...
Pull drm tree changes from Dave Airlie:
"This is the main drm pull request, I have some overlap with sound and
arm-soc, the sound patch is acked and may conflict based on -next
reports but should be a trivial fixup, which I'll leave to you!
Highlights:
- new drivers:
MSM driver from Rob Clark
- non-drm:
switcheroo and hdmi audio driver support for secondary GPU
poweroff, so drivers can use runtime PM to poweroff the GPUs. This
can save 5 or 6W on some optimus laptops.
- drm core:
combined GEM and TTM VMA manager
per-filp mmap permission tracking
initial rendernode support (via a runtime enable for now, until we get api stable),
remove old proc support,
lots of cleanups of legacy code
hdmi vendor infoframes and 4k modes
lots of gem/prime locking and races fixes
async pageflip scaffolding
drm bridge objects
- i915:
Haswell PC8+ support and eLLC support, HDMI 4K support, initial
per-process VMA pieces, watermark reworks, convert to generic hdmi
infoframes, encoder reworking, fastboot support,
- radeon:
CIK PM support, remove 3d blit code in favour of DMA engines,
Berlin GPU support, HDMI audio fixes
- nouveau:
secondary GPU power down support for optimus laptops, lots of
fixes, use MSI, VP3 engine support
- exynos:
runtime pm support for g2d, DT support, remove non-DT,
- tda998x i2c driver:
lots of fixes for sync issues
- gma500:
lots of cleanups
- rcar:
add LVDS support, fbdev emulation,
- tegra:
just minor fixes"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (684 commits)
drm/exynos: Fix build error with exynos_drm_connector.c
drm/exynos: Remove non-DT support in exynos_drm_fimd
drm/exynos: Remove non-DT support in exynos_hdmi
drm/exynos: Remove non-DT support in exynos_drm_g2d
drm/exynos: Remove non-DT support in exynos_hdmiphy
drm/exynos: Remove non-DT support in exynos_ddc
drm/exynos: Make Exynos DRM drivers depend on OF
drm/exynos: Consider fallback option to allocation fail
drm/exynos: fimd: move platform data parsing to separate function
drm/exynos: fimd: get signal polarities from device tree
drm/exynos: fimd: replace struct fb_videomode with videomode
drm/exynos: check a pixel format to a particular window layer
drm/exynos: fix fimd pixel format setting
drm/exynos: Add NULL pointer check
drm/exynos: Remove redundant error messages
drm/exynos: Add missing of.h header include
drm/exynos: Remove redundant NULL check in exynos_drm_buf
drm/exynos: add device tree support for rotator
drm/exynos: Add missing includes
drm/exynos: add runtime pm interfaces to g2d driver
...
- HDPM: Updates for AIO/RayDAT support, TCO/sync support
- RME96: Add PCM sync support
- HD-audio:
* A few HDMI/DP audio updates (CA assignment fix, stream switching
fix, Intel DP device list support)
* Device specific fixes (ASUS/CXT HP mic support, Thinkpad mic
improvements, Chromebook fixes, STAC9228 Dell fixes)
* Replace the all static quirks for AD codecs with the generic
parser
* WAKEEN support for handling irqs in the power saving mode
- USB-audio: Clean up implicit fb handling and related codes
- DAPM is now mandatory for ASoC CODEC drivers; all existing drivers
have had some level of DAPM support added. In addition, a lot of
cleanups and improvements in DAPM.
- Support for ASoC cross-platform compile test
- New drivers and support for Analog Devices ADAU1702 and ADAU1401(a),
Asahi Kasei Microdevices AK4554, Atmel AT91ASM9x5 and WM8904 based
machines, Freescale S/PDIF and SSI AC'97, Renesas R-Car SoCs, Samsung
Exynos5420 SoCs, Texas Instruments PCM1681 and PCM1792A and Wolfson
Microelectronics WM8997
- DT bindings for kirkwood and i.MX S/PDIF
- Clean up and bug fixes: ssm2602, rt5640 and sgtl5000.
- Core helpers for bitbanged AC'97 reset
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=wbLt
-----END PGP SIGNATURE-----
Merge tag 'sound-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"Changes are seen in a wide range of codes, mainly due to ASoC DAPM
requirements; HD-audio shows a high peak in diffstat, it's just a
removal of bunch of old static quirks.
Some highlights:
- HDPM: Updates for AIO/RayDAT support, TCO/sync support
- RME96: Add PCM sync support
- HD-audio:
* A few HDMI/DP audio updates (CA assignment fix, stream switching
fix, Intel DP device list support)
* Device specific fixes (ASUS/CXT HP mic support, Thinkpad mic
improvements, Chromebook fixes, STAC9228 Dell fixes)
* Replace the all static quirks for AD codecs with the generic
parser
* WAKEEN support for handling irqs in the power saving mode
- USB-audio: Clean up implicit fb handling and related codes
- DAPM is now mandatory for ASoC CODEC drivers; all existing drivers
have had some level of DAPM support added. In addition, a lot of
cleanups and improvements in DAPM.
- Support for ASoC cross-platform compile test
- New drivers and support for Analog Devices ADAU1702 and
ADAU1401(a), Asahi Kasei Microdevices AK4554, Atmel AT91ASM9x5 and
WM8904 based machines, Freescale S/PDIF and SSI AC'97, Renesas
R-Car SoCs, Samsung Exynos5420 SoCs, Texas Instruments PCM1681 and
PCM1792A and Wolfson Microelectronics WM8997
- DT bindings for kirkwood and i.MX S/PDIF
- Clean up and bug fixes: ssm2602, rt5640 and sgtl5000.
- Core helpers for bitbanged AC'97 reset"
* tag 'sound-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (375 commits)
ALSA: hda - Re-setup HDMI pin and audio infoframe on stream switches
ALSA: hda - hdmi: Fallback to ALSA allocation when selecting CA
ASoC: mxs-sgtl5000: Configure the dai_links as unidirectional
ASoC: soc-pcm: Allow to specify unidirectional dai_link
ASoC: fsl_spdif: Staticse non-exported symbols
ASoC: ssm2602: Fix cache sync
ASoC: Remove unused sysfs_registered field from snd_soc_codec struct
ASoC: Remove unused debugfs_dapm field from snd_soc_{platform,codec} struct
ASoC: Remove unused control_type field from snd_soc_codec struct
ASoC: fsl: Add one blank space after ':=' in Makefile
ASoC: fsl: Add wrapping for dev_dbg() in fsl_spdif.c
ASoC: rt5640: change widget sequence for depop
ASoC: dapm: Fix auto-disable for inverted controls
ASoC: fsl: Drop SND_SOC_FSL_UTILS from SND_SOC_IMX_SPDIF
ASoC: Samsung: Do not queue cyclic buffers multiple times
ASoC: ep93xx-i2s: Remove unnecessary dev_set_drvdata()
ASoC: designware_i2s: Remove unnecessary dev_set_drvdata()
ASoC: fsl_spdif: remove redundant dev_err call in fsl_spdif_probe()
ASoC: fsl: Add S/PDIF machine driver
ASoc: kirkwood: Use the Kirkwood audio driver in Dove boards
...
When the transcoder:port mapping on Haswell HDMI/DP audio is changed
during the stream playback, the sound gets lost. Typically this
problem is seen when the user switches the graphics mode from eDP+DP
to DP-only configuration, where CRTC 1 is used for DP in the former
while CRTC 0 is used for the latter.
The graphics controller notifies the change via the normal ELD update
procedure, so we get the intrinsic event. For enabling the sound
again, the HDMI audio driver needs to reset the pin and set up the
audio infoframe again.
This patch achieves it by:
- keep the current status of channels and info frame setup in per_pin
struct,
- check the reconnection in the intrinsic event handler,
- reset the pin and the re-invoke hdmi_setup_audio_infoframe()
accordingly.
The hdmi_setup_audio_infoframe() function has been changed, too, so
that it can be invoked without passing the substream instance.
The patch is mostly based on the work by Mengdong Lin.
Cc: Mengdong Lin <mengdong.lin@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
hdmi_channel_allocation() tries to find a HDMI channel allocation that
matches the number channels in the playback stream and contains only
speakers that the HDMI sink has reported as available via EDID. If no
such allocation is found, 0 (stereo audio) is used.
Using CA 0 causes the audio causes the sink to discard everything except
the first two channels (front left and front right).
However, the sink may be capable of receiving more channels than it has
speakers (and then perform downmix or discard the extra channels), in
which case it is preferable to use a CA that contains extra channels
than to use CA 0 which discards all the non-stereo channels.
Additionally, it seems that HBR (HD) passthrough output does not work on
Intel HDMI codecs when CA is set to 0 (possibly the codec zeroes
channels not present in CA). This happens with all receivers that report
a 5.1 speaker mask since a HBR stream is carried on 8 channels to the
codec.
Add a fallback in the CA selection so that the CA channel count at least
matches the stream channel count, even if the stream contains channels
not present in the sink speaker descriptor.
Thanks to GrimGriefer at OpenELEC forums for discovering that changing
the sink speaker mask allowed HBR output.
Reported-by: GrimGriefer
Reported-by: Ashecrow
Reported-by: Frank Zafka <kafkaesque1978@gmail.com>
Reported-by: Peter Frühberger <fritsch@xbmc.org>
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Alex writes:
This is the radeon drm-next request. Big changes include:
- support for dpm on CIK parts
- support for ASPM on CIK parts
- support for berlin GPUs
- major ring handling cleanup
- remove the old 3D blit code for bo moves in favor of CP DMA or sDMA
- lots of bug fixes
[airlied: fix up a bunch of conflicts from drm_order removal]
* 'drm-next-3.12' of git://people.freedesktop.org/~agd5f/linux: (898 commits)
drm/radeon/dpm: make sure dc performance level limits are valid (CI)
drm/radeon/dpm: make sure dc performance level limits are valid (BTC-SI) (v2)
drm/radeon: gcc fixes for extended dpm tables
drm/radeon: gcc fixes for kb/kv dpm
drm/radeon: gcc fixes for ci dpm
drm/radeon: gcc fixes for si dpm
drm/radeon: gcc fixes for ni dpm
drm/radeon: gcc fixes for trinity dpm
drm/radeon: gcc fixes for sumo dpm
drm/radeonn: gcc fixes for rv7xx/eg/btc dpm
drm/radeon: gcc fixes for rv6xx dpm
drm/radeon: gcc fixes for radeon_atombios.c
drm/radeon: enable UVD interrupts on CIK
drm/radeon: fix init ordering for r600+
drm/radeon/dpm: only need to reprogram uvd if uvd pg is enabled
drm/radeon: check the return value of uvd_v1_0_start in uvd_v1_0_init
drm/radeon: split out radeon_uvd_resume from uvd_v4_2_resume
radeon kms: fix uninitialised hotplug work usage in r100_irq_process()
drm/radeon/audio: set up the sads on DCE3.2 asics
drm/radeon: fix handling of variable sized arrays for router objects
...
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_gem_dmabuf.c
drivers/gpu/drm/i915/intel_pm.c
drivers/gpu/drm/radeon/cik.c
drivers/gpu/drm/radeon/ni.c
drivers/gpu/drm/radeon/r600.c
Add support for HDMI audio device on VGA cards that powerdown
to D3cold using non-standard ACPI/PCI infrastructure (optimus).
This does a couple of things to make it work:
a) add a set of power ops for the hdmi domain, and enables them
via vga_switcheroo when we are a switcheroo controlled card. This
just replaces the runtime resume operation so that when the card
is in D3cold the userspace pci config space access via sysfs,
the vga switcheroon runtime resume gets called first and it calls
the GPU resume callback before calling the sound card runtime
resume.
b) standard ACPI/PCI stacks won't put a device into D3cold without
an ACPI handle, but since the hdmi audio devices on gpus don't have
an ACPI handle, we need to manually force the device into D3cold
after suspend from the switcheroo path only.
c) don't try and do runtime s/r when the GPU is off.
d) call runtime suspend/resume during switcheroo suspend/resume
this is to make sure the runtime stack knows to try and resume
the hdmi audio device for pci config space access.
v2: fix incorrect runtime call suspend->resume.
v3: rework irq handler to avoid false irq when we are resuming
but haven't runtime resumed yet, don't bother trying D3cold,
it won't work, just set it manually ourselves, move runtime s/r
calls outside the main s/r hook. enable dnyamic pm properly by
dropping reference.
v4: put back irq handler check just wrap it with cap check
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
CONFIG_SND_HDA_I915 doesn't have to be user-selectable as this is almost
mandatory when i915 driver is available. Let's enable it always when
CONFIG_DRM_I915 is set, so that user won't be bothered by useless
questions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds two fields to unsolicited response, according to spec HDA040-A:
- Device Entry (bit 20:15)
- Inactive (bit 2)
and show the info in debug message.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch is only to allow codec proc file to expose devices list/select info
for Haswell codec pins.
Since Haswell Gfx driver cannot support DP1.2 MST now, so all pins' device list
is empty, meaning no pin is multi-streaming capaple.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If a display codec supports multi-stream transport on the pins, the pin's
device list length and device entries will be exposed to codec proc file.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds flags and routines to get device list & selection info on
a pin.
To support Display Port 1.2 multi-stream transport (MST) over single DP port,
a pin can support multiple devices. Please refer to HD-A spec Document Change
Notificaton HDA040-A.
A display audio codec can set flag "dp_mst" in its patch, indicating its pins
can support MST. But at runtime, a pin may not be multi-streaming capable and
report the device list is empty, depending on Gfx driver configuration.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Using 0x%# emits 0x0x. Only one is necessary.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
As reported by kbuild test robot <fengguang.wu@intel.com>:
warning: (SND_ES1968_RADIO && SND_FM801_TEA575X_BOOL) selects RADIO_TEA575X which has unmet direct dependencies (MEDIA_SUPPORT && RADIO_ADAPTERS && VIDEO_V4L2)
That happens because a radio driver is selected, without selecting the
RADIO_ADAPTERS menu.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
- DAPM is now mandatory for CODEC drivers in order to avoid the repeated
regressions in the special cases for non-DAPM CODECs and make it
easier to integrate with other components on boards. All existing
drivers have had some level of DAPM support added.
- A lot of cleanups in DAPM plus support for maintaining controls in a
specific state while a DAPM widget all contributed by Lars-Peter Clausen.
- Core helpers for bitbanged AC'97 reset from Markus Pargmann.
- New drivers and support for Analog Devices ADAU1702 and ADAU1401(a),
Asahi Kasei Microdevices AK4554, Atmel AT91ASM9x5 and WM8904 based
machines, Freescale S/PDIF and SSI AC'97, Renesas R-Car SoCs, Samsung
Exynos5420 SoCs, Texas Instruments PCM1681 and PCM1792A and Wolfson
Microelectronics WM8997.
- Support for building drivers that can support it cross-platform for
compile test.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=qzif
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v3.12
- DAPM is now mandatory for CODEC drivers in order to avoid the repeated
regressions in the special cases for non-DAPM CODECs and make it
easier to integrate with other components on boards. All existing
drivers have had some level of DAPM support added.
- A lot of cleanups in DAPM plus support for maintaining controls in a
specific state while a DAPM widget all contributed by Lars-Peter Clausen.
- Core helpers for bitbanged AC'97 reset from Markus Pargmann.
- New drivers and support for Analog Devices ADAU1702 and ADAU1401(a),
Asahi Kasei Microdevices AK4554, Atmel AT91ASM9x5 and WM8904 based
machines, Freescale S/PDIF and SSI AC'97, Renesas R-Car SoCs, Samsung
Exynos5420 SoCs, Texas Instruments PCM1681 and PCM1792A and Wolfson
Microelectronics WM8997.
- Support for building drivers that can support it cross-platform for
compile test.
Without the dynamic minor assignment, HDMI codec may have less PCM
instances than the number of pins, which eventually leads to Oops.
Reported-by: Stratos Karafotis <stratosk@semaphore.gr>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixing warning message:
sound/pci/rme96.c: In function ‘snd_rme96_resume’:
sound/pci/rme96.c:2418:19: warning: ignoring return value of ‘pci_enable_device’, declared with attribute warn_unused_result [-Wunused-result]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The headphone automute on this machine triggers annoying pop noises.
It seems that only the first DAC can be used, the secondary DAC always
results in this problem. This patch disables the secondary DAC with
a few additional workarounds.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixed ALC283 D3 to D0 and D0 to D3 Headphone pop noise.
The previous fix [c5177c86: ALSA: hda - Fix the noise after suspend on
ALC283 codec] doesn't work sufficiently for some laptops.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Without proper power management handling, the first use
of a Digi96/8 anytime after a suspend / resume cycle will
start playback with distortions.
v3: Abort if vmalloc() of suspend buffers fail, but do not
leak memory in that case.
[fixed wrong memory leak fix again -- tiwai]
Signed-off-by: Knut Petersen <Knut_Petersen@t-online.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch doesn't change functionality, it only improves readability
and fixes a copy&paste error in a comment.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use enum hdspm_ltc_format's fps_30 (corresponds to 4) instead of 30,
Other case branches return 1, 2 or 3 respectively, so 30 obviously is
wrong.
Since SNDRV_HDSPM_IOCTL_GET_LTC had never been working due to a
copy&paste error in hdspm.h, this change doesn't break userspace.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Yet another entry, just use the existing fixup for this machine, too.
Reported-by: "Nathanael D. Noblet" <nathanael@gnat.ca>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If compiled without CONFIG_SND_HDA_I915, the audio driver cannot
request power well. However, if the power well is on for other
reasons, maybe audio can still work. Therefore, do not skip the
card completely if compiled without CONFIG_SND_HDA_I915.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The higher mic boosts (on internal mic) are so noisy they're unusable
in practice.
BugLink: https://bugs.launchpad.net/bugs/1213820
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move tea575x from sound/i2c/other to drivers/media/radio
Includes Kconfig changes by Hans Verkuil.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Move include/sound/tea575x-tuner.h to include/media/tea575x.h and update files that include it.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This just cleans up the table, no functional changes.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The internal mic boost is so noisy on boosts 2 and 3 so they are
unusable in practice.
BugLink: https://bugs.launchpad.net/bugs/1213055
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Gateway LT27 needs a fixup for the inverted digital mic.
Reported-by: "Nathanael D. Noblet" <nathanael@gnat.ca>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The hardware does support synchronized start/pause/stop of pcm streams,
so there is no reason not to add that feature after more than ten years.
Some minor coding style / white space fixes in the surroundings of the
changes.
Signed-off-by: Knut Petersen <Knut_Petersen@t-online.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current generic parser code assumes that always a pin widget
controls the mute for an output blindly although it might be a
different widget in the middle. Instead of the fixed assumption,
check each parsed path and just pick up the right widget that has been
already defined as a mute control.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The auto-mute using the amp currently works only for a single amp on a
pin. Make it working also with HDA_CTL_BIND_MUTE type, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We've added a fake mute control (setting the amp volume to zero) for
CX5051 at commit [3868137e: ALSA: hda - Add a fake mute feature], but
this feature was overlooked in the generic parser implementation. Now
the driver lacks of mute controls on these codecs.
The fix is just to check both AC_AMPCAP_MUTE and AC_AMPCAP_MIN_MUTE
bits in each place checking the amp capabilities.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=59001
Cc: <stable@vger.kernel.org> [v3.9+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Correct the pins for a line-in and a headphone on LG LW25 laptop with
ALC880 codec. Other pins seem fine.
Reported-and-tested-by: Joonas Saarinen <jonskunator@gmail.com>
Cc: <stable@vger.kernel.org> [v3.9+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The snd_hda_jack_set_gating_jack() call didn't work when
auto_{mute,mic} is suppressed because (1) am_entry is
not filled with nid of the mic pin. (2) The jacks are not
created (by snd_hda_jack_detect_enable_callback) before the
snd_hda_jack_set_gating_jack call.
Now we use the first input pin nid directly, and create the jack if it
doesn't exist yet.
Signed-off-by: Chih-Chung Chang <chihchung@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A fixup for Apple Mac Mini was lost during the adaption to the generic
parser because the fallback for the generic ID 8384:7680 was dropped,
and it resulted in the silence output (and maybe other problems).
Unfortunately, just adding the missing subsystem ID wasn't enough, in
this case. The subsystem ID of this machine is 0000:0100 (what Apple
thought...?), and since snd_hda_pick_fixup() doesn't take the vendor
id zero into account, the driver ignored this entry. Now it's fixed
to regard the vendor id zero as a valid value.
Reported-and-tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: <stable@vger.kernel.org> [v3.9+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
VAIO-Z laptops need to use the specific DAC for the speaker output
by some unknown reason although the codec itself supports the flexible
connection. So we implemented a workaround by a new flag,
no_primary_hp, for assigning the speaker pin first.
This worked until 3.8 kernel, but it got broken because the driver
learned for a better multi-io pin mapping, and not it can assign two
mic pins for multi-io. Since the multi-io requires to be the primary
output, the hp and two mic pins are assigned in prior to the speaker
in the end.
Although the machine has two mic pins, one of them is used as a noise-
canceling headphone, thus it's no real retaskable mic jack. Thus, at
best, we can disable the multi-io assignment and make the parser
behavior back to the state before the multi-io.
This patch adds again a new flag, no_multi_io, to indicate that the
device has no multi-io capability, and set it in the fixup for
VAIO-Z. The no_multi_io flag itself can be used generically, added
via a helper line, too.
Reported-by: Tormen <my.nl.abos@gmail.com>
Reported-by: Adam Williamson <awilliam@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current fixup for dell-bios model with STAC9228 codec contains the
override of pin 0x0c for analog mic. But this is actually just adding
a bogus pin and confuses the parser. Better to remove it for the
auto-mic switching.
Meanwhile, for a possible regression, keep the old configuration as
model=dell-bios-amic, so that people can test it again quickly.
Tested on Dell 1420n laptop.
Reported-and-tested-by: Eric Shattow <lucent@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With runtime power save feature enabled, Headphone hotplug
event will not be detected while controller/codec in D3. HDA has
feature WAKEEN to let codec wake up system if controller is in D3 or
system in S3.(HDA Spec 4.5.9.2/3). Codec can send out INT or wake up
controller depending on whether CIE or GIE enabled.(Figure 4, Interupt
structure).
The controller must be in RESET mode after enter runtime-suspend, otherwise
it will not be waken up even if codec send out wake-up event. And STATESTS
will be cleared after controller brought out of RESET mode.
This patch only enable WAKEEN for runtime-suspend(Controller D3) mode,
not for system S3 mode. with tool "evtest", Headphone hotplug events
could be cought and reported successfully.
[fixed an unused variable warning by tiwai]
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With jackpoll_interval != 0, it's used to poll jack event periodically
in a delayed work. if it's 0, give the caller chance to probe jack status
but will not restart the delayed work.
In the next patch which enable WAKEEN feature, HDA controller was able to wake
up system when it's in D3, it's useful to detect Jack hotplug event and notify
userspace. By default the jackpoll_interval=0, this patch let jack poll once
without starting the delayed work.
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clearing jackpoll_interval before calling cancel_delayed_work_sync(),
otherwise the work will be triggered again and cause impact in
hda_jackpoll_work(). The next patch will poll jack once even with
jackpoll_interval=0.
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Register STATESTS is 16-bit length, use correct API for read/write.
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the power state of ALC283 codec goes to D3, it gives a noise via
headphone output. This is because the driver tries to clear all pins
via snd_hda_shutup_pins(). Setting the mic pin to zero triggers such
a noise.
Define a new shutup call specific to this codec and control the pins
there more precisely. Also, add the power-save enable/disable
sequences in the resume and the new shutup calls.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of calling snd_hda_shutup_pins() unconditionally, allow it be
called in spec->shutup callback. In this way, we can avoid calling
this function if it causes a problem like we see in the next patch
following this.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The usage of strict_strto*() is not preferred, because
strict_strto*() is obsolete. Thus, kstrto*() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_hda_jack_detect() function returns a boolean value for a jack
plugged in or not, but it also returns always true when the
corresponding pin is phantom (i.e. fixed). This is OK in most cases,
but it makes the generic parser misbehaving about the auto-mute or
auto-mic switching, e.g. when one of headphone pins is a fixed.
Namely, the driver decides whether to mute the speaker or not, just
depending on the headphone plug state: if one of the headphone jacks
is seen as active, then the speaker is muted. Thus this will result
always in the muted speaker output.
So, the problem is the function returns a boolean, after all, although
we need to think of "phantom" jack. Now a new function,
snd_hda_jack_detect_state() is introduced to return these tristates.
The generic parser uses this function for checking the headphone or
mic jack states.
Meanwhile, the behavior of snd_hda_jack_detect() is kept as is, for
keeping compatibility in other driver codes.
Acked-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The quirk for Dell laptops with STAC9228 overrides the pin default
config of NID 0x0f to the value with AC_DEFCFG_MISC_NO_PRESENCE bit
on. I'm not quite sure why this was done so, but can guess that this
was introduced for avoiding this to be muted by another headphone
plug. Now, after transition to the generic parser, this workaround
rather causes a problem (notably as unexpected speaker mutes) because
the pin is seen as if it's always plugged in.
Since the generic parser can handle multiple headphone plugging
gracefully, we can get rid of this override now.
Reported-and-tested-by: Eric Shattow <lucent@gmail.com>
Cc: <stable@vger.kernel.org> [v3.9+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The EAPD GPIO is dynamically turned on/off for some machines with
Sigmatel codecs, but this didn't work as expected, and it resulted in
spontaneous lost of speaker outputs per HP plugging or power-saving.
This patch fixes the bug by simply including spec->eapd_mask into
spec->gpio_mask and spec->gpio_data bits.
Reported-and-tested-by: Eric Shattow <lucent@gmail.com>
Cc: <stable@vger.kernel.org> [v3.9+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This Conexant codec has a single jack that can be used as either
headphone or mic (but not headset). The existing hp_mic functionality
does not apply here, because the mic and the HP are on separate pins.
Hence make a lighter version of what has been earlier done for Realtek
codecs.
BugLink: https://bugs.launchpad.net/bugs/1198030
Tested-by: Franz Hsieh <franz.hsieh@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Vendor ID 0x10de0060 is used by a yet-to-be-named GPU chip.
Reviewed-by: Andy Ritger <aritger@nvidia.com>
Signed-off-by: Aaron Plattner <aplattner@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull drm updates from Dave Airlie:
"Okay this is the big one, I was stalled on the fbdev pull req as I
stupidly let fbdev guys merge a patch I required to fix a warning with
some patches I had, they ended up merging the patch from the wrong
place, but the warning should be fixed. In future I'll just take the
patch myself!
Outside drm:
There are some snd changes for the HDMI audio interactions on haswell,
they've been acked for inclusion via my tree. This relies on the
wound/wait tree from Ingo which is already merged.
Major changes:
AMD finally released the dynamic power management code for all their
GPUs from r600->present day, this is great, off by default for now but
also a huge amount of code, in fact it is most of this pull request.
Since it landed there has been a lot of community testing and Alex has
sent a lot of fixes for any bugs found so far. I suspect radeon might
now be the biggest kernel driver ever :-P p.s. radeon.dpm=1 to enable
dynamic powermanagement for anyone.
New drivers:
Renesas r-car display unit.
Other highlights:
- core: GEM CMA prime support, use new w/w mutexs for TTM
reservations, cursor hotspot, doc updates
- dvo chips: chrontel 7010B support
- i915: Haswell (fbc, ips, vecs, watermarks, audio powerwell),
Valleyview (enabled by default, rc6), lots of pll reworking, 30bpp
support (this time for sure)
- nouveau: async buffer object deletion, context/register init
updates, kernel vp2 engine support, GF117 support, GK110 accel
support (with external nvidia ucode), context cleanups.
- exynos: memory leak fixes, Add S3C64XX SoC series support, device
tree updates, common clock framework support,
- qxl: cursor hotspot support, multi-monitor support, suspend/resume
support
- mgag200: hw cursor support, g200 mode limiting
- shmobile: prime support
- tegra: fixes mostly
I've been banging on this quite a lot due to the size of it, and it
seems to okay on everything I've tested it on."
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (811 commits)
drm/radeon/dpm: implement vblank_too_short callback for si
drm/radeon/dpm: implement vblank_too_short callback for cayman
drm/radeon/dpm: implement vblank_too_short callback for btc
drm/radeon/dpm: implement vblank_too_short callback for evergreen
drm/radeon/dpm: implement vblank_too_short callback for 7xx
drm/radeon/dpm: add checks against vblank time
drm/radeon/dpm: add helper to calculate vblank time
drm/radeon: remove stray line in old pm code
drm/radeon/dpm: fix display_gap programming on rv7xx
drm/nvc0/gr: fix gpc firmware regression
drm/nouveau: fix minor thinko causing bo moves to not be async on kepler
drm/radeon/dpm: implement force performance level for TN
drm/radeon/dpm: implement force performance level for ON/LN
drm/radeon/dpm: implement force performance level for SI
drm/radeon/dpm: implement force performance level for cayman
drm/radeon/dpm: implement force performance levels for 7xx/eg/btc
drm/radeon/dpm: add infrastructure to force performance levels
drm/radeon: fix surface setup on r1xx
drm/radeon: add support for 3d perf states on older asics
drm/radeon: set default clocks for SI when DPM is disabled
...
ALC5505 DSP is enabled even though we don't use the features yet at
all. This results in the unnecessarily high power consumption, more
than 100mV higher. Until we implement the DSP support, better to
bypass DSP for saving more power.
Reported-by: Mengdong Lin <mengdong.lin@intel.com>
[Patch modified by Mengdong to cal alc5505_dsp_init() with extra
acl5505_dsp_halt().]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Also use snd_ctl_enum_info() to fill the autosync text fields on AES32
and MADI cards (only users of snd_hdspm_info_autosync_ref).
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Also use snd_ctl_enum_info() to fill the autosync enumerated controls.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use snd_ctl_enum_info() to fill most of the enumerated controls. More
non-trivial occurrences will follow in separate commits.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch finally enables TCO support on RME AES(32) cards.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds a new ALSA control to read the external sample rate from
userspace on RME AES(32) cards.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch refactors the code to query the external sample rate and its
translation into the corresponding enum into a helper function to
prevent future code duplication.
A later commit will make use of this new helper function.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Also report TCO status and Sync-In via /proc/ on AES(32) cards.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch enables the user to select "TCO" and "Sync In" as a preferred
sync reference on RME AES(32) cards.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds support to read the TCO sample rate in
hdspm_external_sample_rate() on RME AES(32) cards.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As mentioned in the comment, the AES32 cards must not set the format
bit, since it is used to indicate the preferred sync setting instead.
We hence simply skip the corresponding part in the hw_params function.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds AES32 specific code to hdspm_get_tco_sample_rate to
query the TCO sample rate.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds AES32 specific code to hdspm_get_wc_sample_rate() to
query the wordclock frequency.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch only introduces prototype declarations, no real change. The
functions themselves are already present.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Helper function to return the AES sample rate class. This class needs to
be translated via HDSPM_bit2freq() to get the more common
representation.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Provide the text for the two new clock options "TCO" and "Sync In" on
AES32 cards.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HDSPM_AUTOSYNC_REF macro is only implemented for MADI and AES32
cards, so it doesn't make sense to call it on AIO boards.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch does nothing, it's sole intent is to clean up the code.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDSPM_tco_lock and HDSPM_tcoLock were too close, so the previous code
didn't honour the difference between the two.
Let's be more verbose and use HDSPM_tcoLockMadi for MADI cards,
HDSPM_tcoLockAes for AES(32) and fix the code that makes use of both.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch separates the TCO bits from snd_hdspm_proc_read_madi(), so
the new function can later be shared between MADI and AES32 cards.
It's essentially only moving code around, no new functionality.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a left-over mistake from old code, the correct register offset is
provided in kcontrol->private_value, not in the index.
Cf. RayDAT case, where it has already been corrected.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AIO cards allow to use AEB (Analogue Expansion Boards) to add four
input and/or output channels.
This patch adds the necessary code to detect and enable the additional
I/O channels.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch uses the newly introduced HDSPM_CONTROL_TRISTATE functions to
create and expose the following ALSA controls:
- Gain selection for Input, Output and Phones (HiGain, +4dBu, -10dbV)
- S/PDIF Input select (Coaxial, Optical, Internal)
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AIO cards offer at least four individual settings options with three
states each. Those settings are represented as two bits in the settings
register with the following meaning:
0*some_base_bit --> Option value 0
1*some_base_bit --> Option value 1
2*some_base_bit --> Option value 2
3*some_base_bit --> mask to select the two involved bits
This patch adds a generic ALSA control macro for such a value-to-bit
pattern mapping. It will be used in a later commit to expose four new
controls.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ENUMERATED_CTL_INFO is a macro, so the binary code is generated multiple
times. To avoid code duplication, refactor the involved functionality
into a function and make ENUMERATED_CTL_INFO a call to this function.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds the following ALSA controls:
- S/PDIF Out Optical to switch S/PDIF Out from coaxial to optical
- S/PDIF Out Professional to send the Pro bit in the output stream
- ADAT-Internal to enable ADAT/TDIF Expansion Board (AEB/TEB)
- XLR Breakout Cable if analogue I/O uses the XLR breakout cable
- WCK48 to force WordClock to the 32-48kHz range (single speed) if
the card is operating at higher frequencies
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds new ALSA controls to send single-speed WordClock and
S/PDIF-Professional on RME RayDAT cards.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
hdspm_set_system_clock_mode() is almost a one-by-one copy of
hdspm_set_toggle_setting(). To improve code quality, remove the
duplication.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HDSPM_TOGGLE_SETTING functions alter the control_register on older
cards. On newer cards (AIO/RayDAT), they have to operate on the
settings_register instead.
This patch augments the existing functions to work with AIO/RayDAT, too.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
RME RayDAT and AIO cards are new designs with different register
settings. Since we need to distinguish them from older cards multiple
times in the driver, refactor the code into a separate helper function.
No functional change intended.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The driver did not support all possible configurations. These defines
will be used by later commits to add the missing functionality.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Finally all the static quirks in patch_analog.c are reduced by this
patch. As machines with AD1986A codec are all old and often their
BIOS are buggy, we need to keep at least a few static pin conifgs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull trivial tree updates from Jiri Kosina:
"The usual stuff from trivial tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
treewide: relase -> release
Documentation/cgroups/memory.txt: fix stat file documentation
sysctl/net.txt: delete reference to obsolete 2.4.x kernel
spinlock_api_smp.h: fix preprocessor comments
treewide: Fix typo in printk
doc: device tree: clarify stuff in usage-model.txt.
open firmware: "/aliasas" -> "/aliases"
md: bcache: Fixed a typo with the word 'arithmetic'
irq/generic-chip: fix a few kernel-doc entries
frv: Convert use of typedef ctl_table to struct ctl_table
sgi: xpc: Convert use of typedef ctl_table to struct ctl_table
doc: clk: Fix incorrect wording
Documentation/arm/IXP4xx fix a typo
Documentation/networking/ieee802154 fix a typo
Documentation/DocBook/media/v4l fix a typo
Documentation/video4linux/si476x.txt fix a typo
Documentation/virtual/kvm/api.txt fix a typo
Documentation/early-userspace/README fix a typo
Documentation/video4linux/soc-camera.txt fix a typo
lguest: fix CONFIG_PAE -> CONFIG_x86_PAE in comment
...
BIOS on Samsung R55, M55 and M50 provide the proper pin-configs,
so we can remove the corresponding static quirk entries gracefully.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For removing static quirks for AD1988 variants, a new fixup defining
the 6stack pinconfig has been added for the buggy BIOS. Other than
that, we can cut off straightforwardly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the necessary device-specific fixups for Thinkpad and HP devices
have been already ported, we can remove all static quirks for AD1884,
AD1984, AD1884A and AD1984A codecs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now the generic parser can work stably enough, we can get rid of the
static quirks. Let's start from AD1882.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The AD1884 HP laptop/mobile quirks control GPIO1 bit as the primary
mute as well. Add the similar control to ad1884 fixup for auto
parser, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ad1884_fixup_hp_eapd() tries to set the NID for controlling the
speaker EAPD from the pin configuration. But the current code can't
work expectedly since it sets spec->eapd_nid before calling the
generic parser where the autocfg pins are set up.
This patch changes the function to set spec->eapd_nid after the
generic parser call while it sets vmaster hook unconditionally. The
spec->eapd_nid check is moved in the hook function itself instead.
Cc: <stable@vger.kernel.org> [v3.9+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The char arrays with size 44 are for the name string of
snd_ctl_elem_id. Define the constant and replace the raw numbers with
it for clarifying better.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
add_control_with_pfx() in hda_generic.c assumes a shorter name string
for the control element, and this resulted in the truncation of the
long but valid string like "Headphone Surround Switch" in the middle.
This patch aligns the max size to the actual limit of snd_ctl_elem_id,
44.
Cc: <stable@vger.kernel.org> [v3.9+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add two more machines that need quirks for headset mics to work.
Tested-by: Shawn Wang <shawn.wang@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1195636
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This quirk is needed for the headset mic to work on this Dell
machine.
BugLink: https://bugs.launchpad.net/bugs/1195597
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the power-saving control for ALC5505 DSP on some
Realtek codecs.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Tested-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Last 3.11 feature pull. I have a few odds bits and pieces and fixes in my
queue, I'll sort them out later on to see what's for 3.11-fixes and what's
for 3.12. But nothing to hold this here up imo.
Highlights:
- more hangcheck work from Mika and Chris to prepare for arb robustness
- trickle feed fixes from Ville
- first parts of the shared pch pll rework, with some basic hw state
readout and cross-checking (this shuts up the confused pch pll refcount
WARN that Linus just recently forwarded)
- Haswell audio power well support from Wang Xingchao (alsa bits acked by
Takashi)
- some cleanups and asserts sprinkling around the plane/gamma enabling
sequence from Ville
- more gtt refactoring from Ben
- clear up the adjusted->mode vs. pixel clock vs. port clock confusion
- 30bpp support, this time for real hopefully
* tag 'drm-intel-next-2013-06-18' of git://people.freedesktop.org/~danvet/drm-intel: (97 commits)
drm/i915: remove a superflous semi-colon
drm/i915: Kill useless "Enable panel fitter" comments
drm/i915: Remove extra "ring" from error message
drm/i915: simplify the reduced clock handling for pch plls
drm/i915: stop killing pfit on i9xx
drm/i915: explicitly set up PIPECONF (and gamma table) on haswell
drm/i915: set up PIPECONF explicitly for i9xx/vlv platforms
drm/i915: set up PIPECONF explicitly on ilk-ivb
drm/i915: find guilty batch buffer on ring resets
drm/i915: store ring hangcheck action
drm/i915: add batch bo to i915_add_request()
drm/i915: change i915_add_request to macro
drm/i915: add i915_gem_context_get_hang_stats()
drm/i915: add struct i915_ctx_hang_stats
drm/i915: Try harder to disable trickle feed on VLV
drm/i915: fix up pch pll enabling for pixel multipliers
drm/i915: hw state readout and cross-checking for shared dplls
drm/i915: WARN on lack of shared dpll
drm/i915: split up intel_modeset_check_state
drm/i915: extract readout_hw_state from setup_hw_state
...
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_fb.c
drivers/gpu/drm/i915/intel_sdvo.c
Use standard PM state macros PCI_Dx instead of numeric 0/1/2..
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As some of ALC269 quirks use the inverted dmic feature, we need to
call alc_inv_dmic_sync() in the resume callback like in alc_resume(),
too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The stac_resume() is exactly what the default resume code does, so
we don't have to define and use it doubly. Let's cut it off.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Hdmi driver may not receive intrinsic event from gfx side when
it's in runtime suspend mode. There's no ELD info when exit from
runtime suspend. This patch avoid missing ELD info.
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch is a cleanup to the previous patch "reset hda link during system/
runtime suspend".
In this patch
- azx_enter_link_reset() and azx_exit_link_reset() are defined for entering and
exiting the link reset respectively. azx_link_reset() is no longer used and
replaced by azx_enter_link_reset().
- azx_reset() reuses the above two new functions for a link reset cycle
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pin's connection list may change dynamically with hot-plug event
on Intel Haswell chip. Users would see connections be "0" in codec#.
when play audio on this pin, software driver choose converter from cache
connections. So add "In-driver connection" info to avoid confuse when
raw connections are different with cache connection.
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We've got bug report wrt many machines with VT1708 (e.g. IBM POS
machines) showing the broken auto-mute behavior. It turned out that
the problem is that the pin control values of the speaker and line-out
pins are completely ignored. As a workaround, let's use the newly
introduced feature of the generic parser, to control the mute via amp
on pins.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new flag, auto_mute_via_amp, to determine the behavior of the
headphone / line-out auto-mute. When this flag is set, the generic
driver mutes the speaker and line outputs via the amp mute of each
pin, instead of changing the pin control values.
This is introduced for devices that don't work expectedly with the pin
control values; for example, some devices are known to keep enabling
the speaker outputs no matter which pin control values are set on the
speaker pins.
The driver doesn't check actually whether the pins have the output amp
caps, but assumes that the proper mixer (mute) controls are created on
all these pins. If not the case, you can't use this flag for your
device.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If all the codecs report ClkStopOK (OK to stop bus clock) after being put to
D3, this patch will reset the HDA link before the controller is put to D3.
So the link will be in reset during system or runtime suspend, the bus clock
stops and the codecs are in D3(ClkStop) state.
This may help to reduce power consumption by dozens of mW on some peripheral
hda codecs.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Like the X220, this quirk was added to support docking station,
so enable the fixup instead.
According to Jan, the generic parser works equal or better
than the current parser. This was tested under a 3.9 kernel.
Reported-by: Jan Alexander Steffens <jan.steffens@gmail.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some VIA codecs like VT1708S have Mic boost amps in the mic pins but
they aren't exposed in the capability bits. In the past driver code,
we override the pin caps and create mic boost controls forcibly.
While transition to the generic parser, we lost the mic boost controls
although the pin caps are still overridden, because the generic parser
code checks the widget caps, too.
So this patch adds a new helper function to allow the override of the
given widget capability bits, and makes VIA codecs driver to add the
missing input-amp capability bit.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=59861
Cc: <stable@vger.kernel.org> [v3.9+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For Intel Haswell HDMI codecs, the pins choose converter 0 by default.
This would cause conflict when playing audio on unused pins,the pin with
physical device connected would get audio data too.
i.e. Pin 0/1/2 default choose converter 0, pin 1 has HDMI monitor connected.
when play audio on Pin 0 or pin 2, pin 1 could get audio data too.
This patch configure unused pins to choose different converter.
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a selection to a converter MUX is changed in hdmi_pcm_open(), it
should be cached so that the given connection can be restored properly
at PM resume. We need just to replace the corresponding
snd_hda_codec_write() call with snd_hda_codec_write_cache().
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Haswell converters maybe in wrong power state before usage.
i.e. only converter 0 is in D0, converter 1/2 are in D3.
When pin choose converter 1/2, there's no audio output, this
cause dependency when playing differnt stream on pins.
AUD_PWRST ConvertorA_Widget_Power_State_Current D0
AUD_PWRST ConvertorA_Widget_Power_State_Requsted D0
AUD_PWRST ConvertorB_Widget_Power_State_Current D3
AUD_PWRST ConvertorB_Widget_Power_State_Requested D3
AUD_PWRST ConvC_Widget_PwrSt_Curr D3
AUD_PWRST ConvC_Widget_PwrSt_Req D3
This patch check converter's power state and set D0 if it's in D3 mode.
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The refactoring by commit 9040d102 introduced the new function
snd_hda_check_power_state(). This function is supposed to return true
if the state already reached to the target state, but it actually
returns false for that. An utterly stupid typo while copy & paste.
Fortunately this didn't influence on much behavior because powering up
AFG usually powers up the child widgets, too. But the finer power
control must have been broken by this bug.
Cc: <stable@vger.kernel.org> [v3.9+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These headset jacks keep coming in on more and more platforms, and
it's possible I don't catch them all. Make it easier to test and
verify by making models.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* for-linus: (635 commits)
ALSA: usb-audio: Fix invalid volume resolution for Logitech HD Webcam c310
ALSA: hda - Fix pin configurations for MacBook Air 4,2
ALSA: usb-audio: work around Android accessory firmware bug
ALSA: hda - Headset mic support for three more machines
Linux 3.10-rc6
smp.h: Use local_irq_{save,restore}() in !SMP version of on_each_cpu().
powerpc: Fix missing/delayed calls to irq_work
powerpc: Fix emulation of illegal instructions on PowerNV platform
powerpc: Fix stack overflow crash in resume_kernel when ftracing
snd_pcm_link(): fix a leak...
use can_lookup() instead of direct checks of ->i_op->lookup
move exit_task_namespaces() outside of exit_notify()
fput: task_work_add() can fail if the caller has passed exit_task_work()
xfs: don't shutdown log recovery on validation errors
xfs: ensure btree root split sets blkno correctly
xfs: fix implicit padding in directory and attr CRC formats
xfs: don't emit v5 superblock warnings on write
mei: me: clear interrupts on the resume path
mei: nfc: fix nfc device freeing
mei: init: Flush scheduled work before resetting the device
...
MacBook Air 4,2 requires the whole default pin configuration table to
be overridden by the driver, as usual, as Apple's machines don't set
up properly after boot. Otherwise mic won't work, and other ill
effect may happen.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=59381
Reported-and-tested-by: Peter John Hartman <peterjohnhartman@gmail.com>
Cc: <stable@vger.kernel.org> [v3.9+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
They need these quirks to have headset mic support.
BugLink: https://bugs.launchpad.net/bugs/1189363
Tested-by: Shawn Wang <shawn.wang@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For Intel Haswell chip, HDA controller and codec have
power well dependency from GPU side. This patch added support
to request/release power well in audio driver. Power save
feature should be enabled to get runtime power saving.
There's deadlock when request_module(i915) in azx_probe.
It looks like:
device_lock(audio pci device) -> azx_probe -> module_request
(or symbol_request) -> modprobe (userspace) -> i915 init ->
drm_pci_init -> pci_register_driver -> bus_add_driver -> driver_attach ->
which in turn tries all locks on pci bus, and when it tries the one on the
audio device, it will deadlock.
This patch introduce a work to store remaining probe stuff, and let
request_module run in safe work context.
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Reviewed-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is a preliminary work for the upcoming Haswell HDMI audio fixes.
azx_first_init() function can be safely called after the f/w loader,
since the f/w loader doesn't require the sound hardware initialization
beforehand. Moving it into azx_probe_continue() cleans up the code
flow a bit.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The device can support runtime PM no matter whether it support
signal wakeup or not. For some chips like Haswell which doesnot
support PME by default, this patch let haswell Display HD-A controller
enter runtime suspend, and bring more power saving whith power-well
feature enabled.
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When a codec is powered off, some systems don't respond properly after
D3 FG transition, while the driver still expects the response and
tries to fall back to different modes (polling and single-cmd). When
the fallback happens, the driver stays in that mode, and falling back
to the single-cmd mode means it'll loose the unsol event handling,
too.
The unresponsiveness at D3 isn't too serious, thus this fallback is
mostly superfluous. We can gracefully ignore the error there so that
the driver keeps the normal operation mode.
This patch adds a new bit flag for codec read/write, set in the power
transition stage, which is notified to the controller driver via a new
bus->no_response_fallback flag.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_hda_codec_read(), snd_hda_codec_write() & co take the argument
"direct" that indicates whether the given NID is a direct reference or
an indirect reference. However, the indirect reference is practically
unimplemented and never exists. And moreover, we don't need the
indication of indirect reference at this high level, as NID can be
represented in 16bit values at this point.
Meanwhile, there are some cases where it'd be nice to give some
operational options to these functions. So, we can reuse this
argument as a new bit flag! Pretty frugal, eh?
All callers so far pass zero to this argument, thus there is no
behavior change by this replacement.
The real usage of this new bit option will be added in the following
patches.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
