This patch takes care of initialising and type-checking sysctls
related to feature negotiation. Type checking is important since some
of the sysctls now directly impact the feature-negotiation process.
The sysctls are initialised with the known default values for each
feature. For the type-checking the value constraints from RFC 4340
are used:
* Sequence Window uses the specified Wmin=32, the maximum is ulong (4 bytes),
tested and confirmed that it works up to 4294967295 - for Gbps speed;
* Ack Ratio is between 0 .. 0xffff (2-byte unsigned integer);
* CCIDs are between 0 .. 255;
* request_retries, retries1, retries2 also between 0..255 for good measure;
* tx_qlen is checked to be non-negative;
* sync_ratelimit remains as before.
Notes:
------
1. Die s@sysctl_dccp_feat@sysctl_dccp@g since the sysctls are now in feat.c.
2. As pointed out by Arnaldo, the pattern of type-checking repeats itself in
other places, sometimes with exactly the same kind of definitions (e.g.
"static int zero;"). It may be a good idea (kernel janitors?) to consolidate
type checking. For the sake of keeping the changeset small and in order not
to affect other subsystems, I have not strived to generalise here.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds full support for local/remote Sequence Window feature, from which the
* sequence-number-validity (W) and
* acknowledgment-number-validity (W') windows
derive as specified in RFC 4340, 7.5.3.
Specifically, the following is contained in this patch:
* integrated new socket fields into dccp_sk;
* updated the update_gsr/gss routines with regard to these fields;
* updated handler code: the Sequence Window feature is located at the TX side,
so the local feature is meant if the handler-rx flag is false;
* the initialisation of `rcv_wnd' in reqsk is removed, since
- rcv_wnd is not used by the code anywhere;
- sequence number checks are not done in the LISTEN state (cf. 7.5.3);
- dccp_check_req checks the Ack number validity more rigorously;
* the `struct dccp_minisock' became empty and is now removed.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This initialises feature negotiation from two tables, which are in
turn are initialised from sysctls.
As a novel feature, specifics of the implementation (e.g. that short
seqnos and ECN are not yet available) are advertised for robustness.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes the use of the sysctl and the minisock variable for the Send Ack
Vector feature, as it now is handled fully dynamically via feature negotiation
(i.e. when CCID-2 is enabled, Ack Vectors are automatically enabled as per
RFC 4341, 4.).
Using a sysctl in parallel to this implementation would open the door to
crashes, since much of the code relies on tests of the boolean minisock /
sysctl variable. Thus, this patch replaces all tests of type
if (dccp_msk(sk)->dccpms_send_ack_vector)
/* ... */
with
if (dp->dccps_hc_rx_ackvec != NULL)
/* ... */
The dccps_hc_rx_ackvec is allocated by the dccp_hdlr_ackvec() when feature
negotiation concluded that Ack Vectors are to be used on the half-connection.
Otherwise, it is NULL (due to dccp_init_sock/dccp_create_openreq_child),
so that the test is a valid one.
The activation handler for Ack Vectors is called as soon as the feature
negotiation has concluded at the
* server when the Ack marking the transition RESPOND => OPEN arrives;
* client after it has sent its ACK, marking the transition REQUEST => PARTOPEN.
Adding the sequence number of the Response packet to the Ack Vector has been
removed, since
(a) connection establishment implies that the Response has been received;
(b) the CCIDs only look at packets received in the (PART)OPEN state, i.e.
this entry will always be ignored;
(c) it can not be used for anything useful - to detect loss for instance, only
packets received after the loss can serve as pseudo-dupacks.
There was a FIXME to change the error code when dccp_ackvec_add() fails.
I removed this after finding out that:
* the check whether ackno < ISN is already made earlier,
* this Response is likely the 1st packet with an Ackno that the client gets,
* so when dccp_ackvec_add() fails, the reason is likely not a packet error.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updating the NDP count feature is handled automatically now:
* for CCID-2 it is disabled, since the code does not use NDP counts;
* for CCID-3 it is enabled, as NDP counts are used to determine loss lengths.
Allowing the user to change NDP values leads to unpredictable and failing
behaviour, since it is then possible to disable NDP counts even when they
are needed (e.g. in CCID-3).
This means that only those user settings are sensible that agree with the
values for Send NDP Count implied by the choice of CCID. But those settings
are already activated by the feature negotiation (CCID dependency tracking),
hence this form of support is redundant.
At startup the initialisation of the NDP count feature uses the default
value of 0, which is done implicitly by the zeroing-out of the socket when
it is allocated. If the choice of CCID or feature negotiation enables NDP
count, this will then be updated via the NDP activation handler.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TX/RX CCIDs of the minisock are now redundant: similar to the Ack Vector
case, their value equals initially that of the sysctl, but at the end of
feature negotiation may be something different.
The old interface removed by this patch thus has been replaced by the newer
interface to dynamically query the currently loaded CCIDs.
Also removed are the constructors for the TX CCID and the RX CCID, since the
switch "rx <-> non-rx" is done by the handler in minisocks.c (and the handler
is the only place in the code where CCIDs are loaded).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch, TX/RX CCIDs can now be changed on a per-connection
basis, which overrides the defaults set by the global sysctl variables
for TX/RX CCIDs.
To make full use of this facility, the remaining patches of this patch
set are needed, which track dependencies and activate negotiated
feature values.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch deprecates the Ack Ratio sysctl, since
* Ack Ratio is entirely ignored by CCID-3 and CCID-4,
* Ack Ratio currently doesn't work in CCID-2 (i.e. is always set to 1);
* even if it would work in CCID-2, there is no point for a user to change it:
- Ack Ratio is constrained by cwnd (RFC 4341, 6.1.2),
- if Ack Ratio > cwnd, the system resorts to spurious RTO timeouts
(since waiting for Acks which will never arrive in this window),
- cwnd is not a user-configurable value.
The only reasonable place for Ack Ratio is to print it for debugging. It is
planned to do this later on, as part of e.g. dccp_probe.
With this patch Ack Ratio is now under full control of feature negotiation:
* Ack Ratio is resolved as a dependency of the selected CCID;
* if the chosen CCID supports it (i.e. CCID == CCID-2), Ack Ratio is set to
the default of 2, following RFC 4340, 11.3 - "New connections start with Ack
Ratio 2 for both endpoints";
* what happens then is part of another patch set, since it concerns the
dynamic update of Ack Ratio while the connection is in full flight.
Thanks to Tomasz Grobelny for discussion leading up to this patch.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides feature negotiation for server minimum checksum coverage
which so far has been missing.
Since sender/receiver coverage values range only from 0...15, their
type has also been reduced in size from u16 to u4.
Feature-negotiation options are now generated for both sender and receiver
coverage, i.e. when the peer has `forgotten' to enable partial coverage
then feature negotiation will automatically enable (negotiate) the partial
coverage value for this connection.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous setsockopt interface, which passed socket options via struct
dccp_so_feat, is complicated/difficult to use. Continuing to support it leads to
ugly code since the old approach did not distinguish between NN and SP values.
This patch removes the old setsockopt interface and replaces it with two new
functions to register NN/SP values for feature negotiation.
These are essentially wrappers around the internal __feat_register functions,
with checking added to avoid
* wrong usage (type);
* changing values while the connection is in progress.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides a data structure to record which CCIDs are locally supported
and three accessor functions:
- a test function for internal use which is used to validate CCID requests
made by the user;
- a copy function so that the list can be used for feature-negotiation;
- documented getsockopt() support so that the user can query capabilities.
The data structure is a table which is filled in at compile-time with the
list of available CCIDs (which in turn depends on the Kconfig choices).
Using the copy function for cloning the list of supported CCIDs is useful for
feature negotiation, since the negotiation is now with the full list of available
CCIDs (e.g. {2, 3}) instead of the default value {2}. This means negotiation
will not fail if the peer requests to use CCID3 instead of CCID2.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides feature-negotiation initialisation for both DCCP sockets
and DCCP request_sockets, to support feature negotiation during
connection setup.
It also resolves a FIXME regarding the congestion control
initialisation.
Thanks to Wei Yongjun for help with the IPv6 side of this patch.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
A lookup table for feature-negotiation information, extracted from RFC
4340/42, is provided by this patch. All currently known features can
be found in this table, along with their feature location, their
default value, and type.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 4340, 7.7 specifies up to 6 bytes for the NDP Count option, whereas the code
is currently limited to up to 3 bytes. This seems to be a relict of an earlier
draft version and is brought up to date by the patch.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
In DCCP, timestamps can occur on packets anytime, CCID3 uses a timestamp(/echo) on the Request/Response
exchange. This patch addresses the following situation:
* timestamps are recorded on the listening socket;
* Responses are sent from dccp_request_sockets;
* suppose two connections reach the listening socket with very small time in between:
* the first timestamp value gets overwritten by the second connection request.
This is not really good, so this patch separates timestamps into
* those which are received by the server during the initial handshake (on dccp_request_sock);
* those which are received by the client or the client after connection establishment.
As before, a timestamp of 0 is regarded as indicating that no (meaningful) timestamp has been
received (in addition, a warning message is printed if hosts send 0-valued timestamps).
The timestamp-echoing now works as follows:
* when a timestamp is present on the initial Request, it is placed into dreq, due to the
call to dccp_parse_options in dccp_v{4,6}_conn_request;
* when a timestamp is present on the Ack leading from RESPOND => OPEN, it is copied over
from the request_sock into the child cocket in dccp_create_openreq_child;
* timestamps received on an (established) dccp_sock are treated as before.
Since Elapsed Time is measured in hundredths of milliseconds (13.2), the new dccp_timestamp()
function is used, as it is expected that the time between receiving the timestamp and
sending the timestamp echo will be very small against the wrap-around time. As a byproduct,
this allows smaller timestamping-time fields.
Furthermore, inserting the Timestamp Echo option has been taken out of the block starting with
'!dccp_packet_without_ack()', since Timestamp Echo can be carried on any packet (5.8 and 13.3).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The option parsing code currently only parses on full sk's. This causes a problem for
options sent during the initial handshake (in particular timestamps and feature-negotiation
options). Therefore, this patch extends the option parsing code with an additional argument
for request_socks: if it is non-NULL, options are parsed on the request socket, otherwise
the normal path (parsing on the sk) is used.
Subsequent patches, which implement feature negotiation during connection setup, make use
of this facility.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a socket option and signalling support for the case where the server
holds timewait state on closing the connection, as described in RFC 4340, 8.3.
Since holding timewait state at the server is the non-usual case, it is enabled
via a socket option. Documentation for this socket option has been added.
The setsockopt statement has been made resilient against different possible cases
of expressing boolean `true' values using a suggestion by Ian McDonald.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the necessary state transitions for the two forms of passive-close
* PASSIVE_CLOSE - which is entered when a host receives a Close;
* PASSIVE_CLOSEREQ - which is entered when a client receives a CloseReq.
Here is a detailed account of what the patch does in each state.
1) Receiving CloseReq
The pseudo-code in 8.5 says:
Step 13: Process CloseReq
If P.type == CloseReq and S.state < CLOSEREQ,
Generate Close
S.state := CLOSING
Set CLOSING timer.
This means we need to address what to do in CLOSED, LISTEN, REQUEST, RESPOND, PARTOPEN, and OPEN.
* CLOSED: silently ignore - it may be a late or duplicate CloseReq;
* LISTEN/RESPOND: will not appear, since Step 7 is performed first (we know we are the client);
* REQUEST: perform Step 13 directly (no need to enqueue packet);
* OPEN/PARTOPEN: enter PASSIVE_CLOSEREQ so that the application has a chance to process unread data.
When already in PASSIVE_CLOSEREQ, no second CloseReq is enqueued. In any other state, the CloseReq is ignored.
I think that this offers some robustness against rare and pathological cases: e.g. a simultaneous close where
the client sends a Close and the server a CloseReq. The client will then be retransmitting its Close until it
gets the Reset, so ignoring the CloseReq while in state CLOSING is sane.
2) Receiving Close
The code below from 8.5 is unconditional.
Step 14: Process Close
If P.type == Close,
Generate Reset(Closed)
Tear down connection
Drop packet and return
Thus we need to consider all states:
* CLOSED: silently ignore, since this can happen when a retransmitted or late Close arrives;
* LISTEN: dccp_rcv_state_process() will generate a Reset ("No Connection");
* REQUEST: perform Step 14 directly (no need to enqueue packet);
* RESPOND: dccp_check_req() will generate a Reset ("Packet Error") -- left it at that;
* OPEN/PARTOPEN: enter PASSIVE_CLOSE so that application has a chance to process unread data;
* CLOSEREQ: server performed active-close -- perform Step 14;
* CLOSING: simultaneous-close: use a tie-breaker to avoid message ping-pong (see comment);
* PASSIVE_CLOSEREQ: ignore - the peer has a bug (sending first a CloseReq and now a Close);
* TIMEWAIT: packet is ignored.
Note that the condition of receiving a packet in state CLOSED here is different from the condition "there
is no socket for such a connection": the socket still exists, but its state indicates it is unusable.
Last, dccp_finish_passive_close sets either DCCP_CLOSED or DCCP_CLOSING = TCP_CLOSING, so that
sk_stream_wait_close() will wait for the final Reset (which will trigger CLOSING => CLOSED).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds two auxiliary states to deal with passive closes:
* PASSIVE_CLOSE (reached from OPEN via reception of Close) and
* PASSIVE_CLOSEREQ (reached from OPEN via reception of CloseReq)
as internal intermediate states.
These states are used to allow a receiver to process unread data before
acknowledging the received connection-termination-request (the Close/CloseReq).
Without such support, it will happen that passively-closed sockets enter CLOSED
state while there is still unprocessed data in the queue; leading to unexpected
and erratic API behaviour.
PASSIVE_CLOSE has been mapped into TCPF_CLOSE_WAIT, so that the code will
seamlessly work with inet_accept() (which tests for this state).
The state names are thanks to Arnaldo, who suggested this naming scheme
following an earlier revision of this patch.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This decouples PARTOPEN from TCP-specific stream-states.
It thus addresses the FIXME.
The code has been checked with regard to dependency on PARTOPEN and FIN_WAIT1
states (to which PARTOPEN previously was mapped): there is no difference, as
PARTOPEN is always referred to directly (i.e. not via the mapping to TCP
state).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for converting the 11 currently defined Reset codes into system
error numbers, which are stored in sk_err for further interpretation.
This makes the externally visible API behaviour similar to TCP, since a client
connecting to a non-existing port will experience ECONNREFUSED.
* Code 0, Unspecified, is interpreted as non-error (0);
* Code 1, Closed (normal termination), also maps into 0;
* Code 2, Aborted, maps into "Connection reset by peer" (ECONNRESET);
* Code 3, No Connection and
Code 7, Connection Refused, map into "Connection refused" (ECONNREFUSED);
* Code 4, Packet Error, maps into "No message of desired type" (ENOMSG);
* Code 5, Option Error, maps into "Illegal byte sequence" (EILSEQ);
* Code 6, Mandatory Error, maps into "Operation not supported on transport endpoint" (EOPNOTSUPP);
* Code 8, Bad Service Code, maps into "Invalid request code" (EBADRQC);
* Code 9, Too Busy, maps into "Too many users" (EUSERS);
* Code 10, Bad Init Cookie, maps into "Invalid request descriptor" (EBADR);
* Code 11, Aggression Penalty, maps into "Quota exceeded" (EDQUOT)
which makes sense in terms of using more than the `fair share' of bandwidth.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This fixes a problem when analysing erroneous packets in dccp_v{4,6}_err:
* dccp_hdr_seq currently takes an skb
* however, the transport headers in the skb are shifted, due to the
preceding IPv4/v6 header.
Fixed for v4 and v6 by changing dccp_hdr_seq to take a struct dccp_hdr as
argument. Verified that the correct sequence number is now reported in the
error handler.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This
* removes a declaration of a non-existent function
__dccp_minisock_init;
* shifts the initialisation function dccp_minisock_init() from
options.c to minisocks.c, where it is more naturally expected to
be.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables applications to query the current value of the Maximum
Packet Size via a socket option, suggested as a SHOULD in (RFC 4340,
p. 102).
This socket option is useful to avoid the annoying bail-out via
`-EMSGSIZE'. In particular, as fragmentation is not currently
supported (and its use is partly discouraged in RFC 4340).
With this option, it is possible to size buffers accordingly, e.g.
int buflen = dccp_get_cur_mps(sockfd);
/* or */
if (msgsize > dccp_get_cur_mps(sockfd))
die("message is too large for this path");
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements a SHOULD from RFC 4340, 7.5.4:
"To protect against denial-of-service attacks, DCCP implementations SHOULD
impose a rate limit on DCCP-Syncs sent in response to sequence-invalid packets,
such as not more than eight DCCP-Syncs per second."
The rate-limit is maintained on a per-socket basis. This is a more stringent
policy than enforcing the rate-limit on a per-source-address basis and
protects against attacks with forged source addresses.
Moreover, the mechanism is deliberately kept simple. In contrast to
xrlim_allow(), bursts of Sync packets in reply to sequence-invalid packets
are not supported. This foils such attacks where the receipt of a Sync
triggers further sequence-invalid packets. (I have tested this mechanism against
xrlim_allow algorithm for Syncs, permitting bursts just increases the problems.)
In order to keep flexibility, the timeout parameter can be set via sysctl; and
the whole mechanism can even be disabled (which is however not recommended).
The algorithm in this patch has been improved with regard to wrapping issues
thanks to a suggestion by Arnaldo.
Commiter note: Rate limited the step 6 DCCP_WARN too, as it says we're
sending a sync.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
This adds fields to support the informational Data 1..3 fields of the
DCCP-Reset packets (RFC 4340, 5.6), and makes minor cosmetic changes
to documentation.
Code which fills in these fields follows in subsequent patches, it is
primarily used for reporting option-processing and feature-negotiation
errors.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
This fills in missing documentation for dccp_sock fields.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the places where we need a pointer to the transport header, it is
still legal to touch skb->h.raw directly if just adding to,
subtracting from or setting it to another layer header.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the common, open coded 'skb->h.raw = skb->data' operation, so that we can
later turn skb->h.raw into a offset, reducing the size of struct sk_buff in
64bit land while possibly keeping it as a pointer on 32bit.
This one touches just the most simple cases:
skb->h.raw = skb->data;
skb->h.raw = {skb_push|[__]skb_pull}()
The next ones will handle the slightly more "complex" cases.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
That accumulated over the last months hackaton, shame on me for not
using git-apply whitespace helping hand, will do that from now on.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This removes and cleans up unused variables and structures which have become
unnecessary following the introduction of the EWMA patch to automatically track
the CCID 3 receiver/sender packet sizes `s'.
It deprecates the PACKET_SIZE socket option by returning an error code and
printing a deprecation warning if an application tries to read or write this
socket option.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch does not change code; it performs some trivial clean/tidy-ups:
* removal of a `debug_prefix' string in favour of the
already existing dccp_role(sk)
* add documentation of structures and constants
* separated out the cases for invalid packets (step 1
of the packet validation)
* removing duplicate statements
* combining declaration & initialisation
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch replaces cryptic feature negotiation messages of type
Oct 31 15:42:20 kernel: dccp_feat_change: feat change type=32 feat=1
Oct 31 15:42:21 kernel: dccp_feat_change: feat change type=34 feat=1
Oct 31 15:42:21 kernel: dccp_feat_change: feat change type=32 feat=5
into ones of type:
Nov 2 13:54:45 kernel: dccp_feat_change: ChangeL(CCID (1), 3)
Nov 2 13:54:45 kernel: dccp_feat_change: ChangeR(CCID (1), 3)
Nov 2 13:54:45 kernel: dccp_feat_change: ChangeL(Ack Ratio (5), 2)
Also,
* completed the feature number list wrt RFC 4340 sec. 6.4
* annotating which ones have been implemented so far
* implemented rudimentary sanity checking in feat.c (FIXMEs)
* some minor fixes
Commiter note: uninlined dccp_feat_name and dccp_feat_typename, for
consistency with dccp_{state,packet}_name, that, BTW,
should be compiled only if CONFIG_IP_DCCP_DEBUG is
selected, leaving this to another cset tho. Also
shortened dccp_feat_negotiation_debug to dccp_feat_debug.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This patch does the following:
a) introduces variable-length checksums as specified in [RFC 4340, sec. 9.2]
b) provides necessary socket options and documentation as to how to use them
c) basic support and infrastructure for the Minimum Checksum Coverage feature
[RFC 4340, sec. 9.2.1]: acceptability tests, user notification and user
interface
In addition, it
(1) fixes two bugs in the DCCPv4 checksum computation:
* pseudo-header used checksum_len instead of skb->len
* incorrect checksum coverage calculation based on dccph_x
(2) removes dccp_v4_verify_checksum() since it reduplicates code of the
checksum computation; code calling this function is updated accordingly.
(3) now uses skb_checksum(), which is safer than checksum_partial() if the
sk_buff has is a non-linear buffer (has pages attached to it).
(4) fixes an outstanding TODO item:
* If P.CsCov is too large for the packet size, drop packet and return.
The code has been tested with applications, the latest version of tcpdump now
comes with support for partial DCCP checksums.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This is a code simplification:
it combines three often recurring operations into one inline function,
* allocate `len' bytes header space in skb
* fill these `len' bytes with zeroes
* cast the start of this header space as dccp_hdr
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This has been discussed on dccp@vger and removes the necessity for applications
to supply service codes in each and every case.
If an application does not want to provide a service code, that's fine, it will
be given 0. Otherwise, service codes can be set via socket options as before.
This patch has been tested using various client/server configurations
(including listening on multiple service codes).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
This adds transmit buffering to DCCP.
I have tested with CCID2/3 and with loss and rate limiting.
Signed off by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will later be included in struct dccp_request_sock so that we can
have per connection feature negotiation state while in the 3way
handshake, when we clone the DCCP_ROLE_LISTEN socket (in
dccp_create_openreq_child) we'll just copy this state from
dreq_minisock to dccps_minisock.
Also the feature negotiation and option parsing code will mostly touch
dccps_minisock, which will simplify some stuff.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per the draft. This fixes the build when netfilter dccp components
are built and dccp isn't. Thanks to Reuben Farrelly for reporting
this.
The following changesets will introduce /proc/sys/net/dccp/defaults/
to give more flexibility to DCCP developers and testers while apps
doesn't use setsockopt to specify the desired CCID, etc.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This also fixes the layout of dccp_hdr short sequence numbers, problem
was not fatal now as we only support long (48 bits) sequence numbers.
Signed-off-by: Andrea Bittau <a.bittau@cs.ucl.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. No need for ->ccid_init nor ->ccid_exit, this is what module_{init,exit}
does and anynways neither ccid2 nor ccid3 were using it.
2. Rename struct ccid to struct ccid_operations and introduce struct ccid
with a pointer to ccid_operations and rigth after it the rx or tx
private state.
3. Remove the pointer to the state of the half connections from struct
dccp_sock, now its derived thru ccid_priv() from the ccid pointer.
Now we also can implement the setsockopt for changing the CCID easily as
no ccid init routines can affect struct dccp_sock in any way that prevents
other CCIDs from working if a CCID switch operation is asked by apps.
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now CCID2 is the default, as stated in the RFC drafts, but we allow
a config where just CCID3 is built, where CCID3 becomes the default.
Signed-off-by: Ian McDonald <imcdnzl@gmail.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
